DS1830/A DS183
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any
device may be simultaneously available through various sales channels. For information about device errata, click here: http://dbserv.maxim-
ic.com/errata.cfm.
1 of 7 060303
FEATURES
§ 5V (DS1830) or 3.3V (DS1830A) power-on
reset
§ Excellent for systems that need power-on
resets in a consistent sequence
§ Asserts resets during power transients
§ Pushbutton reset input for system override
§ Selectable reset timing
§ Reduces need for discrete components
§ Precision temperature-compensated voltage
reference
§ 8-pin DIP, 8-pin SO, or space saving 8-pin
µSOP
§ Operating temperature of -40°C to +85°C
§ Open-drain, active-low inputs
PIN ASSIGNMENT
PIN DESCRIPTION
1 PBRST - Pushbutton Reset Input
2 TD - Time Delay Select Input
3 TOL - VCC Tolerance Select Input
4 GND - Ground
8 VCC - Power Supply
7 RST1 - Reset 1 Output
6 RST2 - Reset 2 Output
5 RST3 - Reset 3 Output
DESCRIPTION
The DS1830 Reset Sequencer monitors the power supply for an in-tolerance condition and the pushbutton
reset input for a manual reset. First a precision temperature-compensated reference and comparator circuit
monitors the status of the power supply and when an out-of-tolerance condition is detected, an internal
power fail signal is generated that forces the reset lines to go to an active state. If the power supply
returns to an in-tolerance condition, RST1 will release followed by RST2 and finally RST3 . Sequencing of
resets allows for systems to power-up in an orderly manner providing superior reliability.
www.maxim-ic.com
DS1830/A
Reset Sequence Pushbutton
D1830/A
2 of 7
OPERATION — POWER MONITOR
The DS1830 provides the functions of detecting out-of-tolerance conditions on a power supply and
warning a processor based system of impending power failure. When VCC is detected as out-of-tolerance
all reset outputs will be forced active. When VCC returns to a valid state, RST1 will remain active for
period of time based on the condition of the TD input. Reset outputs RST2 and RST3 follow RST1 , each
one at the proper delays for the condition of the TD input. All resets will remain in the inactive state
(high) until the next VCC out-of-tolerance condition or pushbutton reset. On power-up all resets are kept
active for an appropriate period determined by the status of the TD input after the power supply inputs
have reached the selected tolerance. This allows the power supply and system power to stabilize before
the reset sequences are released.
BLOCK DIAGRAM Figure 1
OPERATION — TOLERANCE SELECT
The DS1830/A provides a TOL input for individual customization of the DS1830x to specific application
requirements (see Table 1). For the tolerance selection, see Table 1 below. The TOL input is only
sampled while VCC is below the lowest potential trip value and can not be changed after the VCC voltage
exceeds the lowest potential trip value.
TOL — TOLERANCE SELECT Table 1
TOL 5V (DS1830) 3.3V (DS1830A)
VCC 5% 5%
GND 10% 10%
OPEN
(N.C.) 15% 20%
D1830/A
3 of 7
OPERATION — PUSHBUTTON RESET
The DS1830 provides a pushbutton switch for manual reset control. When any of the DS1830/A resets
are not active (low) a reset cycle can be initiated by a pushbutton reset. The pushbutton reset is generated
by pulling the PBRST pin low for at least 1ms. When the push- button is held low all resets are forced
active. The reset will remain active until the pushbutton input is released and then will start a sequenced
time-out based on the condition of the TD input. The Pushbutton input is pulled high through an internal
40kW pull-up resistor and debounced via internal circuitry. See Figure 2 for an application example and
Figure 3 for the timing diagram.
PUSHBUTTON RESET Figure 2
TIMING DIAGRAM — PUSHBUTTON RESET Figure 3
OPERATION — TIME DELAY SELECT
The DS1830 provides an input to select three time delay characteristics for the reset outputs. The TD
input has 3 states high (VCC), low (ground) and no connect (N.C.). Table 2 details the minimum timing
based on the state of the TD input. If the TD input is connected to ground; RST1 will have a minimum
time delay of 10 ms after VCC is in tolerance. If the TD input is floated; RST1 will have a minimum time
delay of 20 ms after VCC is in tolerance. If the TD input is connected to VCC, RST1 will have a minimum
time delay of 50 ms after VCC is in tolerance. An oscillator and clock chain generate the reset timing with
each time delay based on the same device oscillator. The time delay for RST2 will be 5 times as long as
RST1 and RST3 will be 10 times the duration of RST1 .
TD CONTROL MINIMUM RESET TIMING Table 2
TD TRST1 TRST2 TRST3
TD = GND 10ms 50ms 100ms
TD = N.C. 20ms 100ms 200ms
TD = VCC 50ms 250ms 500ms
D1830/A
4 of 7
APPLICATION DIAGRAM — CASCADE DELAY CONFIGURATIONS Figure 4
Note 1: The RST3 output tied to the pushbutton reset would be pulled to VCC through the 40kW resistor in
the pushbutton input. If a stronger pull-up is required an additional pull-up resistor could be added.
Note 2: When using the cascade configuration, it is important that the TOL pins of the master and the
slave are configured so that the master’s VCCTP is greater than the slave’s VCCTP. This will ensure that
when the master’s higher VCCTP is crossed, the resets will ripple through to the slave.
TIMING DIAGRAM — POWER-DOWN Figure 5
MASTER
SLAVE
SEE NOTE 2
SEE NOTE 2
SEE NOTE 1
D1830/A
5 of 7
TIMING DIAGRAM — POWER-UP Figure 6
ABSOLUTE MAXIMUM RATINGS*
Voltage on any Pin Relative to
Ground
-0.5V to +6.0V
Operating Temperature -40°C to +85°C
Storage Temperature -55°C to +125°C
Soldering Temperature See IPC/JEDEC J-STD-020A
* This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS (-40°C to +85°C)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Supply Voltage VCC 1.0 5.5 V 1
PBRST Input High
Level VIH 2.0 VCC + 0.3 V
PBRST Input Low
Level VIL -0.3 +0.5 V
D1830/A
6 of 7
DC ELECTRICAL CHARACTERISTICS (-40°C to +85°C; VCC = 1.0V to 5.5V)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
VCC Trip Point (TOL=
VCC) DS1830 VCCTP 4.50 4.62 4.74 V
VCC Trip Point
(TOL=GND) DS1830 VCCTP 4.25 4.37 4.49 V
VCC Trip Point
(TOL=Open) DS1830 VCCTP 4.00 4.13 4.24 V
VCC Trip Point (TOL=
VCC) DS1830A VCCTP 2.98 3.06 3.15 V
VCC Trip Point
(TOL=GND) DS1830A VCCTP 2.80 2.88 2.97 V
VCC Trip Point
(TOL=Open) DS1830A VCCTP 2.47 2.55 2.64 V
Input Leakage IIL -1.0 +1.0 µA2
Output Current @ 0.4V IOL 20 mA 3
DS1830 18 35
Operating Current
(Standby) ICC DS1830A 10 25 µA4
AC ELECTRICAL CHARACTERISTICS (-40°C to +85°C; VCC = 1.0V to 5.5V)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
PBRST = VIL tPB tPDLY ms
RESET Active Time
(RST1 /TD =GND) tRST1 10 15 20 ms
RESET Active Time
(RST1 /TD =Float) tRST1 20 30 40 ms
RESET Active Time
(RST1 /TD = VCC)tRST1 50 75 100 ms
RESET Active Time
(RST2 )tRST2
5x
tRST1ms
RESET Active Time
(RST3 )tRST3
10x
tRST1ms
VCC Detect to RST tRPD 58µs5
VCC Slew Rate tF20 µs6
VCC Detect to RST tRPU
See RESET Active
Times ms 7
VCC Slew Rate tR0ns
PBRST Stable Low to
RST tPDLY 1.0 1.5 2.0 ms
CAPACITANCE (TA = +25°C)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Capacitance CIN 5pF
Output Capacitance COUT 7pF
D1830/A
7 of 7
NOTES:
1. All voltages are referenced to ground.
2. PBRST is internally pulled up to VCC with an internal impedance of 40kW typical.
3. Measured with PBRST = VCC and RST1 , RST2 , and RST3 open.
4. Measured with outputs open and all inputs at VCC or Ground (except TD and TOL can be floating).
5. Noise Immunity - Pulses < 2ms at VCC TP minimum will not cause a reset.
6. The tF value is for reference in defining values for tRPD and should not be considered a requirement for
proper operation or use of the device.
7. See tRST1, tRST2, and tRST3 for specific tRPU AC timing parameters.
ORDERING INFORMATION
PART # PIN PACKAGE TEMP TYPE
DS1830 8-DIP 300-MIL -40°C to +85°C5V Reset Sequencer
DS1830S 8-SO 150-MIL -40°C to +85°C5V Reset Sequencer
DS1830U 8-µSOP 118-MIL -40°C to +85°C5V Reset Sequencer
DS1830A 8-DIP 300-MIL -40°C to +85°C3.3V Reset Sequencer
DS1830AS 8-SO 150-MIL -40°C to +85°C3.3V Reset Sequencer
DS1830AU 8-µSOP 118-MIL -40°C to +85°C3.3V Reset Sequencer