Product Specification
G64128X20 series
Crystal Clear Technology sdn. bhd.
16Jalan TP5—Taman Perindustrian Sime UEP
47600 Subang Jaya—Selangor DE
Malaysia. T: +603 80247099 F: +603 80247098
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
1
1.0 Table of Contents
Page
1. Table of Contents 1
2. Record of revision 2
3. General specification 3
4. Absolute maximum ratings 4
5. Electrical characteristics 4
6. Environmental requirement 4
7. LCD specification 5 ~ 7
8. Interface 8
9. Functional Description 9 ~ 12
10. Instructions 13~ 14
11. Power supply 14
12. Quality assurance 15 ~ 20
13. Precautions in use LCM 21 ~ 22
14. Outline drawing 23 ~ 24
15. LCD Segment and Common Layout 25
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
2
2.0 Record of revision
Rev Date Item Page Comment Originator Checked By
1.0
2.0
12/09/08
11/11/08
12
15
Initial Release
Update of Quality Assurance
specifications.
Syam
Syam
Azhar
Azhar
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
3
3.0 General specification
Display format: Graphics 128 (w) x 64 (h) dots
Dot size: 0.34 (w) x 0.34 (h) mm
Dot pitch: 0.37 (w) x 0.37 (h) mm
View area: 51.0 (w) x 28.0 (h) mm
Active area: 47.33 (w) x 23.65 (h) mm
General dimensions: 57.20 (w) x 45.20 (h) x 6.0 (t) mm
Controller/Driver: NT7534 or equivalent
Interface: Parallel/Serial
Driving method: 1/64 duty, 1/9 bias
Y : Yellow Green (STN)
G : Grey (STN)
B : Black & White (FSTN)
N : Negative (FSTN) Blue ( Single Retardation )
U : Negative (FSTN) Black/White ( Double Retardation )
S : Negative (STN)
Z : Negative (FSTN) Black/White ( Double Retardation ) TRI-AXIS
8
SERIES NUMBER FOR THIS STANDARD SPECIFICATION
00 - STANDARD SPECIFICATION MODEL
T0 - WITH TOUCH PANEL
REFER TO FACTORY FOR OTHER VERSIONS. TERMS AND CONDITIONS APPLY
SEMI - CUSTOMISE (MINOR CHANGES FROM STANDARD MODEL)
SERIES NUMBER FOR THIS STANDARD SPECIFICATION
N : Normal Temperature ( 0°C to +50°C ), where storage temperature is (-20°C to +70°C)
W : Wide Temperature ( -20°C to +70°C ), where storage temperature is (-30°C to +80°C)
B : Bottom view ( 6 O'clock )
T : Top view ( 12 O'clock )
OPERATING TEMPERATURE
VIEWING ANGLE
LCD MODE
MODULE VERSION
S : Side Led Backlight (Yellow Green)
B : Side Led Backlight (Blue)
W : Side Led Backlight (White)
N : No Backlight
MODEL NUMBER
BACKLIGHT MODE
STD. GRAPHIC : No. of rows followed by no. of column
G412620 0 0
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
4
4.0 Absolute maximum rating (at Vss = 0V, ambient temperature = 25°C)
NO ITEM SIMBOL MIN MAX UNIT
1. Operating Voltage Range VDD -0.3 4.0 V
2. Operating Temperature Top Refer page 3 °C
3. Storage Temperature Tst Refer page 3 °C
5.0 Electrical characteristics
NO ITEM SYMBOL CONDITION MIN TYP MAX UNIT
1. Operating Voltage VDD - - 3.3 - V
2. Power Supply
voltage VLCD 25°C 8.0±5% V
3. Current Supply IDD VDD = 3.3V
4x Boosting - 120 400 uA
5.1 Backlight Options
FORWARD VOLTAGE
(V)
FORWARD CURRENT
(mA)
NO COLOR
Min Typ. Max Min Typ. Max
MIN
BRIGHTNESS
(cd/m2) *
1. Yellow Green - 4.2 - - 30 45 45
2. White - 6.5 - - 45 60 85
3. Blue - 6.5 - - 45 60 70
*Note : 1. Brightness measured at backlight surface.
2. On LCD surface, brightness is only about 10% to 15% of backlight brightness.
3. Lifetime of backlight: For YG = 50K hrs. For White, Blue = 20K hrs
6.0 Environmental requirements
NO ITEM CONDITION
1. Operating
Temperature
Refer page 3
2. Storage Temperature Refer page 3
3. Operating Humidity 5% to 95%RH
4. Cycle Test 0 C @ 30 min to 50 C @ 30min for 1 cycle
run for 10 cycles
5. Lifetime 50000 HOURS (excluding backlight)
Note: The background on LCD has the possibility to be changed in different temperature range.
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
5
7.0 LCD specification
7.1 Electro-optical characteristics (at ambient temperature = 25°C)
LCD TYPE
UNIT
NO ITEM SYMBOL CONDITION STN
YG
STN
GREY
STN
-VE
BLUE
FSTN
+VE
B/W
FSTN
–VE
BLUE
FSTN -
VE
TRUE
B/W
FSTN
-VE
TRI
AXIS
REF.
1
Operating
Voltage
(Volt)
VLCD θ = 0
Cr = max 8.0 ± 5% 7.1.1
θ x 1 +25 +20 +35 +25 +35 +35 +40
θ x 2 -25 -20 -35 -25 -35 -40 -40
θ y 1 -30 -25 -35 -30 -35 -35 -50
2
Viewing
Angle
(Deg)
θ y 2
CR 2
VLCD =
14.7V +30 +25 +35 +30 +35 +35 +30
7.1.2
3 Contrast
Ratio CR
θ = 00
VLCD
=14.7V
3.0 2.3 6.0 3.0 6.0 20 20 7.1.3
Rise
Time
(Tr)
θ = 00 200
4
Response
Time
(msec) Decay
Time
(Td)
θ = 00 250
7.1.4
Note:
1. Viewing angle data is based on bottom view product by default. Should it be a
top view product, values are then swap.
2. Contrast ratio is based on typical data when using white colour as backlight.
3. Equipment Used Eldim; Ez Contrast 120R , Spot Size = 2mm
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
6
NO CHARACTERISTICS DEFINITIONS
7.1.1
Definition of Operating
Voltage (VLCD)
VLCD
1/F
VLCD : Operating Voltage
F : Frame Frequency
7.1.2
Definition of Viewing
Angle
TOP
θ REAR
LEFT RIGHT
FRONT
BOTTOM
REAR (θy2)
LEFT(θx2) RIGHT(θx1)
FRONT (θy1)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
7
7.1.3
Definition of Contrast
Ratio
NON-SELECT WAVE
BRIGHTNESS (%)
SELECT WAVE
b
a
OPERATION VOLTAGE
Contrast Ratio = Brightness of non-selected state (b)
Brightness of selected state (a)
Conditions
(a) Operating Voltage: VLCD
(b) Temperature: 25°C
(c) Viewing Angle, θ = 0o
7.1.4
Response Time
Luminance
(%)
90
10
Tr: Measured between 10% and 90% of LCD segment
maximum response with VON.
Td: With voltage switches to zero and the instant LCD
segment reaches 10% of its maximum response.
Td
Tr
Time
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
8
8.0 Interface
8.1 Display Driver NT7534 OR EQUIVALENT
8.3 Pin No Symbol Description
1 /CS Chip select input pins
2 /RES Reset input pin
3 RS Register select input pin
4 R/W(/WR) Read/Write execution control pin
5 E(/RD) Read/Write execution control pin
6 D0 8 bit bi-directional data bus
7 D1 8 bit bi-directional data bus
8 D2 8 bit bi-directional data bus
9 D3 8 bit bi-directional data bus
10 D4 8 bit bi-directional data bus
11 D5 8 bit bi-directional data bus
12 D6 8 bit bi-directional data bus
13 D7 8 bit bi-directional data bus
14 VDD Power Supply
15 VSS Ground
16 VOUT Voltage converter I/O pin
17 C4+ Positive connection for capacitor 4
18 C3+ Positive connection for capacitor 3
19 C1- Negative connection for capacitor 1
20 C1+ Positive connection for capacitor 1
21 C2+ Positive connection for capacitor 2
22 C2- Negative connection for capacitor 2
23 V1 Driving supply voltage
24 V2 Driving supply voltage
25 V3 Driving supply voltage
26 V4 Driving supply voltage
27 V0 Driving supply voltage
28 P/S Parallel/Serial data input select pin
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
9
9.0 Functional Descriptions
9.1 Read/Write timing characteristics
Read/Write characteristics (6800 series MPU)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
10
Read/Write characteristics (8080 series MPU)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
11
Read/Write characteristics (Serial Interface 4 Wire)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
12
9.2 Application Circuits
9.2.1 6800 (8080) MPU Interface
/
CS
/RES
RS
R/W(/WR)
E(/RD)
DB0 to DB7
VDD
VSS
MPU LCD Module
9.2.2 Serial Interface
/
CS
/RES
RS
SID
SCLK
VDD
VSS
MPU LCD Module
/CS
/RES
RS
R/W(/WR)
E(/RD)
DB0 to DB7
/CS
/RES
RS
DB7(SID)
DB6(SCLK)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
13
10. Instruction Set
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
14
11. Power Supply
(C1 = 1.0 ~ 4.7 uF)
Refer to 5.1
for Backlight supply
For backlight version only
LED A
LED K
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
15
12.0 12.0 Quality Assurance
12.1 ZONE DEFINITION
12.2 REJECTION CRITERIA
12.2.1 DIMENSIONAL DEFECTS
Defect
Category
Defect
Description Criterion Drawing Specification
Glass Size Dimensions of
LCD, do not
conform to the
drawing
Reject Refer to LCD Physical
Dimension Drawing
Perimeter
Seal
Extension
Perimeter seal
epoxy enters the
effective viewing
area
Reject
End Seal
Size
Size of end seal
does not meet
drawing
specification
Reject Refer to LCD Physical
Dimension Drawing
12.2.2 VISUAL DEFECTS
Defect Category Defect
Description Criterion Drawing Specification
Fracture A type of
glass
breakage
containing
running
cracks.
Inspectors
should
attempt to
remove it
with
fingernail. If
removed,
evaluate as
chip
Reject – if the size
is > 30% of the
contact ledge width.
EFFECTIVE VIEWING AREA
ZONE A
ZONE B
(Outside Viewing Area)
ZONE C
(Sealing Area)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
16
Defect Category Defect
Description Criterion Drawing Specification
Chip Chip in
cross over
area
1) Reject - if the
chip causes
crossover dot to be
exposed
2) Chip on outside
edge of the glass
plate but is greater
than 50% of glass
thickness at
crossover dot is
reject able.
Chip Chip in
contact pad
area
Accept if:-
a) X 2.0mm
b) Y 0.5mm
c) Z disregard
Chip in non-
contact pad
area
Accept if:-
a) X 6.0mm
b) Y 1.0mm
c) Z disregard
Chip in
perimeter
seal area
Accept if:-
a) Y 1/3 of
perimeter seal width
(W)
b) X 3.0mm
c) Z disregard
d) X and Y not
touch crossover dot
Corner Chip Corner chip
within seal
area
Accept if:-
a) X 1/3 of
perimeter seal
width (W)
b) Y 1/3 of
perimeter seal
width (W)
c) Z disregard
Chip
Epoxy of
crossover dot
exposed
Z
X
Y
W
Z
Y
X
X
Y
Z
Y
X
Y
Z
X
Y
X
Z
W
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
17
Defect Category Defect
Description Criterion Drawing Specification
Corner chip
not effecting
contact pad /
ITO
Accept if:-
a) XY 4mm2
AND
b) Y D and X
2.0mm
c) Z disregard
Corner chip
effecting
contact pad /
ITO
A) Accept if:-
a) XY 4mm2
AND
b) Y D and X
2.0mm
B) Accept if:-
a) X1 2.0mm
b) Y1 0.5mm
Z disregard
Glass flare A thin layer
of glass
flare at
contact area
Accept if:-
a) Flare thickness
¼ W when W
3mm
b) Flare thickness
1mm when W >
3mm
W: Contact ledge
width
Glass burr A rough
edge(s) left
along the
scribing
edge (i.e.
along the
edges of
display)
Reject – if the burr
cause undersize or
oversize of the LCD
Refer to LCD Physical Dimension Drawing
Rainbow Colored ring
in sharp
blotches
observed
Reject – if 3 or more
colored rings in
sharp blotches of
color are observed.
(Limit samples
should be used
when applicable)
Y
X
D
Z
D
X
X1
Y Y1
A
B
Z
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
18
Defect Category Defect
Description Criterion Drawing Specification
Discoloration Reject - if the
discolorations enter
the active viewing
area of LCD. Color
of the LCD shall
follow product
specification as
specified in the
manufacturing
specification
Air Void LC does not
fulfill the
display
Reject
Fill end
contamination
Discoloratio
n at end seal
area
Reject if
discoloration
exceeded the baffle
(for display with
baffle) or viewing
area (for display
without baffle)
12.2.3 POLARIZER DEFECT
Defect
Category Defect Description Criterion Drawing Specification
Polarizer
defect
Polarizer coverage 1- Polarizer should cover effective viewing
area of display.
2- It is acceptable if perimeter seal bolder at
all sides could be seen.
3- It is acceptable if polarizer attaching
position meeting the tolerance mentioned
in the drawing.
4- It is reject able if polarizer edge jagged
and not even
Refer to LCD Physical
Dimension Drawing
Polarizer Peeling /
delamination
1- Reject if any edge or corner of the
polarizer is lifted up or not adheres to the
glass
Polarizer Scratches 1- Any scratch should be acceptable if it is
not visible from viewing distance at head of
position
2-Polarizer scratch in viewing area is reject
able if it is visible from the specified
viewing distance
3-Defect, which is visible under surface
glare, should be disregard
Polarizer damage 1-Stain mark or depression in front polarizer
surface should be acceptable if it is not
visible from viewing distance at head on
position.
2-Defect, which is visible under surface
glare, should be disregard
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
19
Defect
Category Defect Description Criterion Drawing Specification
Zone / Acceptable No.
Dimension A
D 0.15mm NC B C
0.15 < D 0.30mm 3 NC NC
0.30 < D 0.50mm 2 5 NC
0.50 < D 1.0mm 0 3 NC
NC: No count 1 NC
D: Mean Diameter of Defect
Accept - if air bubble at the seal area does
not propagate into effective viewing area
Polarizer bubble /
Foreign material
12.2.4 FUNCTIONAL DEFECT
Defect
Category Defect Description Criterion Drawing Specification
Missing
common
Part of the pattern
does not light up
Reject
Missing
segment
One or few segment
does not light up
Reject
Common-
common short
Common and
common connected
Reject
Segment-
segment short
Segment and
segment connected
Reject
Common –
segment short
Common and
segment connected
Reject
Wrong
viewing angle
Wrong viewing
angle
Reject if display viewing angle not conform
to customer requirement
Metal residue Extra spot lights up
at the border of the
segment.
Accept if 0.20mm (mean diameter)
Slow response Response of the
display on one side
slower than the
other side
Reject if it is visible at 30cm distance
Reverse twist/
tilt
Segment are darker
or clearer than other
area of the same
segment
Reject
Misalignment Segment fatter or
smaller or extra
segment
Reject if > 10% of designed segment width
and visible at 30cm distance
Acceptable No. Zone /
Dimension A B C
D < 0.10mm NC NC NC
0.10<D < 0.20mm 3 3 NC
NC: No count
Pin Hole Pin hole / void at
light up segment
D: Mean Diameter of Defect
A
B
D = (A + B)/2
A
B
D = (A + B)/2
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
20
Defect
Category Defect Description Criterion Drawing Specification
Segment
Smearing
Light up segment
smear
Reject
Dim segment Display shows poor
contrast at pre set
voltage
Reject
12.2.5 BLACK SPOT, WHITE SPOT AND FOEREIGN MATERIAL
Defect
Category Defect Description Criterion Drawing Specification
Zone / Acceptable No.
Dimension A B C
D < 0.10mm NC NC NC
0.10<D < 0.20mm 3 3 NC
0.20 < D < 0.30mm 1 2 NC
D > 0.30 mm 0 0 NC
NC: No count
Black Spot,
White Spot
and Foreign
Material
Black Spot, White
Spot and Foreign
Material
D: Mean Diameter of Defect
12.2.6 LINE SHAPE AND SCRATCHES
Defect
Category Defect Description Criterion Drawing Specification
Zone /Dimension Acceptable No.
X Y A B C
- <0.01mm
NC NC NC
< 2 mm
< 0.02mm
1 1 NC
<1 mm
< 0.0 2mm
1 2 NC
Line shape and
scratches
Line shape and
scratches
Note: Total defects shall not exceed five
A
B
D = (A + B)/2
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
21
13. Precaution for using LCM
1. Liquid Crystal Display (LCD)
LCD is made up of glass, organic sealant, organic fluid and
polymer based polarizers. The following precautions should
be taken when handling.
b) Keep the temperature within the range of use and
storage. Excessive temperature and humidity
could cause polarization degredation, polarizer
peel off or bubble.
c) Do not contact the exposed polarizer with
anything harder than HB pencil lead. To clean
dust off the display surface, wipe gently with
cotton, chamois or other soft material soaked in
petroleum benzin.
d) Wipe off saliva or water drops immediately.
Contact with water over a long period of time
may cause polarizer deformation or colour
fading, while an active LCD with water
condensation on its surface will cause corrosion
of ITO electrodes.
e) Glass can be easily chipped or cracked from
rough handling, especially at corners and edges.
f) Do not drive LCD with DC voltage.
2. Liquid Crystal Display Modules.
2.1 Mechanical Considerations
LCM are assembled and adjusted with a high
degree of precision. Avoid excessive shocks and
do not make any alterations or modification. The
following should be noted.
a) Do not tamper in any way with the tabs
on the metal frame.
b) Do not modify the PCB by drilling
extra holes, changing its outline,
moving its component or modifying its
pattern.
c) Do not touch the elastomer connector,
especially insert a backlight panel (for
example, EL)
d) When mounting a LCM make sure that
the PCB is not under any stress such as
bending or twisting. Elastomer contacts
are very delicate and missing pixels
could result from slight dislocation of
any of the elements.
a) Avoid pressing on the metal bezel,
otherwise the elastomer connector
could be deformed and lose contact,
resulting in missing pixels.
2.2 Static Electricity
LCM contains CMOS LSI’s and the same
precaution for such devices should apply, namely
a) The operator should be grounded whenever
he/she comes into contact with the module.
Never touch any of the conductive parts
such as the LSI pads, the copper leads on the
PCB and the interface terminals with any
parts of the human body.
b) The modules should be kept in antistatic
bags or other containers to static for storage.
c) Only properly grounded soldering irons
should be used.
d) If an electric screwdriver is used, it should
be well grounded and shielded from
commutator spark.
e) The normal static prevention measures
should be observed for work clothes and
working benches, the latter conductive
(rubber) mat is recommended.
f) Since dry air is inductive to statics, a relative
humidity of 50-60% is recommended.
2.3 Soldering
a) Solder only to the I/O terminals.
b) Use only soldering irons with proper
grounding and no leakage.
c) Soldering temperature: 280 °C
d) Soldering time: 3 to 4 sec
e) Use eutectic solder with resin flux fill.
f) If flux is used, the LCD surface should be
covered to avoid flux spatters. Flux residue
should be removed afterwards.
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
22
2.4 Operation
a) The contras can be adjusted by varying the
LCD driving voltage V0
b) Driving voltage should be kept within
specified range, excess voltage shortens
display life.
c) Response time increases with decrease in
temperature.
d) Display may turn black or dark blue at
temperature above its operational range, this
is (however not pressing on the viewing
area) may cause the segments to appear
“fractured”.
e) Mechanical disturbance during operation (
such as pressing on the viewing area) may
cause the segments to appear “fractured”.
2.5 Storage
If any fluid leaks out of the damage glass cell,
wash off any human part that comes into contact
with soap and water. Never swallow the fluid.
The toxicity is extremely low but caution should
be exercised at all the time.
2.6 Limited Warranty
Unless otherwise agreed between Crystal Clear
Technology and customer, Crystal Clear
Technology will replace or repair any of its LCD
and LCM which is found to be defective
electrically and visually when inspected in
accordance with Crystal Clear Technology
acceptance standards, for a period of one year
from date of shipment. Confirmation of such date
shall be based on freight documents. The
warranty liability of Crystal Clear Technology is
limited to repair and/or replacement on the terms
set forth above. Crystal Clear Technology will
not responsible for any subsequent or
consequential events.
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
23
42.10
1.6
1.0
4.1
0.6
6.0±0.3
1.64.0
DETAIL C
2 - 2.5 6.0±0.3
55.2
2 - 3.0
44.2
31.7
5.5
11.75
2 - 2.5
A
SOLDER PAD
K
47.33 - A/A
51.0 - V/A
55.1±0.2
23.65 - A/A
28.0V/A
43.2±0.2
45.2
48.2
CONTACT SIDE
STIFFENER
0.30±0.05
E
1
H
F
G
A
C
D
B
1
E
MECHANICAL
SPECIFICATION
G64128x20xxx00
DRAWING NUMBER
2354678
APPROVED
Crystal-C lear Technology
NTS
9
12-09-2008
10
16, JLN TP5, TMN PERINDUSTRIAN SIME UEP,
47500 SUBANG JAYA, SELANGOR DARUL EHSAN.
CHECKED
AZHAR
DRAWN
UNIT : MM 11
11
H
1
SHEET REV.
F
G
23 54678910
A
C
D
B
11
1.6
2.0
1.0
4.0 1.6
DETAIL C
SCALE 2:1
1.03.0 3.0
7.1
8.0±1.0
1.6
4.0
DETAIL B
SCALE 2:1
1.0
0.3±0.5 - DST
1.6
3.0
1.0
DETAIL B
3.0
44.2
3.0
44.2
10.0 12.1
0.340
0.370
0.340
0.370
0.35±0.05
0.5±0.1
P0.5 X (28-1) = 13.5±0.1
14.5±0.1
0.5±0.1
3.0±0.5
5.0±1.0
15 VSS
23 V1
27
28
26
24
25
V0
PS
V4
V2
V3
19
22
21
20
16
17
18
C1-
C1+
C2-
C2+
VOUT
C4+
C3+
11
13
12
14
7
8
10
9
D5
D7
D6
VDD
D1
D2
D4
D3
/R/W(/WR)
SYMBOL
4
3
6
5
PIN OUT
2
1
PIN NO
/RS
D0
RD)
/RES
/CS
NOTE :
1. GENERALTOLERANCE TO BE ±0.3
15.7±1.0
14.5
28 01
14.5
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64128x20xxx00 REV 2.0
24
LCD Segment and Common Layout
Crystal Clear Technology
16 Jalan TP5—Taman Perindustrian Sime UEP
47600 Subang Jaya—Selangor DE
Malaysia