Q45BW22 Series Sensors 90 to 250V ac photoelectric sensors with protected solid-state relay output Q45BW22 Series Features * Advanced one-piece photoelectric sensors with outstanding optical performance and extremely rugged design * 90 to 250V ac * Protected solid-state relay output; 300 mA max. load at up to 250V ac * Multiple sensing modes include: opposed, diffuse, retroreflective and convergent, plus glass and plastic fiber optic models * Switchable light/dark operate * Versatile plug-in modules available for output timing logic and/or signal strength display * Highly visible Power, Signal (AIDTM System*), and Output indicator LEDs * Choice of prewired 2 m (6.5') or 9 m (30') unterminated cable, plus Mini-style or Micro-style quick-disconnect fittings * Versatile mounting options * Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and IEC IP67 rating R *U.S. Patent no. 4356393 Because of their extremely high excess gain, these opposed-mode sensors are an excellent option for sensing in contaminated or dirty areas, and are also the best choice for long-range sensing. Infrared, 880 nm Q45BW22 Series Opposed-Mode Emitter (E) and Receiver (R) Models Models Range Cable Supply Output Voltage Type Excess Gain Beam Pattern Effective Beam: 13 mm Q452E Emitter 2-wire 2m (6.5') Q45BW22R Receiver 3-wire 2m (6.5') 60 m (200') 90 to 250V ac Q452EQ Emitter 3-Pin Mini-style QD Q452EQ1 Emitter 4-Pin Micro-style QD Q45BW22RQ Receiver 3-Pin Mini-style QD Q45BW22RQ1 Receiver 4-Pin Micro-style QD NOTES: 1000 SPST Solidstate Relay E X C E S S G A I N Q45E/R Q45E/R Opposed Mode 100 1.5 m 60 in Opposed Mode 1.0 m 40 in 0.5 m 20 in 0 0 10 0.5 m 20 in 1.0 m 40 in 60 in 1.5 m 0 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft 100 m 330 ft 12 m 40 ft 24 m 80 ft 36 m 120 ft 48 m 160 ft 60 m 200 ft DISTANCE DISTANCE i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g., Q452E W/30) ii) A model with a QD connector requires a mating cable; see page 10. IMPORTANT: SEE SAFETY USE WARNING ON BACK PAGE Printed in USA Aug 2013 04/01 P/N 37209 rev. D E Q45BW22 Series The visible red sensing beam of these sensors makes them very easy to align. Model Q45BW22LP polarizes the emitted light and filters out unwanted reflections, making sensing possible in applications otherwise considered unsuited to retroreflective sensing. Performance is specified using the model BRT-3 3" reflector (see the Accessories section of your current Banner Photoelectric Sensors catalog for further information). P Visible red, 680 nm Non-Polarized Polarized Q45BW22 Series Retroreflective-Mode Models Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Non-Polarized 1000 Q45LV Q45BW22LV Q45BW22LVQ 3-wire 2 m (6.5') 0.08 to 9 m (3" to 30') Q45BW22LVQ1 3-Pin Mini-style QD 90 to 250V ac SPST Solid-state Relay 4-Pin Micro-style QD E X C E S S Retroreflective Mode 100 Q45LV 75 mm 2.0 in 25 mm 1.0 in 0 G A I N 3.0 in Retroreflective Mode 50 mm With BRT-3 Reflector 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft 0 With BRT-3 Reflector 10 25 mm 1.0 in 50 mm 2.0 in 75 mm 10 m 33 ft 3.0 in 0 3m 10 ft DISTANCE 6m 20 ft 9m 30 ft 12 m 40 ft 15 m 50 ft DISTANCE Polarized 1000 Q45LP 3-wire 2 m (6.5') Q45BW22LP Q45BW22LPQ Q45BW22LPQ1 0.15 to 6 m (6" to 20') 3-Pin Mini-style QD 4-Pin Micro-style QD 90 to 250V ac SPST Solid-state Relay E X C E S S Retroreflective Mode 100 Q45LP 75 mm Retroreflective Mode 50 mm 25 mm G A I N With BRT-3 Reflector 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft DISTANCE 10 m 33 ft 0 With BRT-3 Reflector 25 mm 1.0 in 50 mm 2.0 in 75 mm 3.0 in 0 1.5 m 5 ft 3m 10 ft 4.5 m 15 ft 6m 20 ft 7.5 m 25 ft DISTANCE NOTES: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g., Q45BW22LV W/30) ii) A model with a QD connector requires a mating cable; see page 10. page 2 2.0 in 1.0 in 0 10 3.0 in Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 Q45BW22 Series Infrared, 880 nm These diffuse-mode models detect objects by sensing the reflection of their own emitted light. Ideal for use when the reflectivity and profile of the object to be sensed are sufficient to return a large percentage of emitted light back to the sensor. Model Q45BW22DX is the first choice for diffuse-mode applications when there are no background objects to falsely return light. Q45BW22 Series Diffuse-Mode Models Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card Short Range 1000 3-wire 2 m (6.5') Q45BW22D Q45BW22DQ 45 cm (18") 3-Pin Mini-style QD Q45D E X C E S S 90 to 250V ac SPST Solid-state Relay 0.6 in Q45D 10 mm 100 0.4 in Diffuse Mode 5 mm 0.2 in 0 10 G A I N 0 5 mm 0.2 in 10 mm 0.4 in 15 mm 4-Pin Micro-style QD Q45BW22DQ1 15 mm Diffuse Mode 1 1.0 mm 0.04 in 0.6 in 0 10 mm 0.4 in 100 mm 4.0 in 100 mm 200mm 300 mm 400 mm 500 mm 4.0 in 8.0 in 12.0 in 16.0 in 20.0 in 1000 mm 40 in DISTANCE DISTANCE Long Range 1000 Q45DL 3-wire 2 m (6.5') Q45BW22DL Q45BW22DLQ E X C E S S 1. 8 m (6') 3-Pin Mini-style QD 90 to 250V ac SPST Solid-state Relay G A I N Diffuse Mode 100 3.0 in 50 mm 2.0 in 25 mm 1.0 in 0 0 10 1 .01 m .033 ft 4-Pin Micro-style QD Q45BW22DLQ1 Q45DL Diffuse Mode 75 mm 25 mm 1.0 in 50 mm 2.0 in 75 mm 3.0 in 0 .10 m .33 ft 1.0 m 3.3 ft 10 m 33 ft 0.6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10 ft DISTANCE DISTANCE High Power 1000 3-wire 2 m (6.5') Q45BW22DX Q45BW22DXQ Q45BW22DXQ1 3m (10') 3-Pin Mini-style QD 4-Pin Micro-style QD 90 to 250V ac SPST Solid-state Relay E X C E S S G A I N Q45DX Diffuse Mode 3.0 in Diffuse Mode 50 mm 2.0 in 25 mm 1.0 in 0 10 0 25 mm 1.0 in 50 mm 2.0 in 75 mm 1 0.01 m 0.033 ft 3.0 in 0 0.1 m 0.33 ft 1.0 m 3.3 ft DISTANCE Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 Q45DX 75 mm 100 10 m 33 ft 0.6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10 ft DISTANCE page 3 Q45BW22 Series These sensors are ideal for reflective sensing of very small parts or profiles, and can accurately sense the position of parts approaching from the side. Will ignore all but highly reflective objects that are outside the sensing range. Visible red, 680 nm Q45BW22 Series Convergent-Mode Models Models Focus Cable Supply Voltage Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card 1000 Q45BW22CV Q45BW22CVQ Q45BW22CVQ1 38 mm (1.5") Spot Size at Focus: 1.3 mm (0.05") 3-wire 2 m (6.5') 3-Pin Mini-style QD 90 to 250V ac SPST Solid-state Relay 4-Pin Micro-style QD E X C E S S G A I N Q45CV Convergent Mode Q45CV 3.8 mm 2.5 mm 0.10 in 1.2 mm 0.05 in 0 10 1 1 mm .04 in 0.15 in Convergent Mode 100 0 1.2 mm 0.05 in 2.5 mm 0.10 in 3.8 mm 0.15 in 0 10 mm .4 in 100 mm 4 in 1000 mm 40 in 38 mm 1.5 in 75 mm 113 mm 150 mm 190 mm 3.0 in 4.5 in 6.0 in 7.5 in DISTANCE DISTANCE 1000 Q45BW22CV4 100 mm (4") Spot Size at Focus: Q45BW22CV4Q1 1.5 mm (0.06") Q45BW22CV4Q 3-wire 2 m (6.5') 3-Pin Mini-style QD 4-Pin Micro-style QD 90 to 250V ac SPST Solid-state Relay E X C E S S Q45CV4 Convergent Mode Q45CV4 3.8 mm 100 0.10 in 1.2 mm 0.05 in 0 G A I N 10 0 1.2 mm 0.05 in 2.5 mm 0.10 in 3.8 mm 1 1 mm .04 in 0.15 in Convergent Mode 2.5 mm 10 mm .4 in 100 mm 4 in DISTANCE 1000 mm 40 in 0.15 in 0 38 mm 1.5 in 75 mm 113 mm 150 mm 190 mm 3.0 in 4.5 in 6.0 in 7.5 in DISTANCE NOTES: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g., Q45BW22CV W/30) ii) A model with a QD connector requires a mating cable; see page 10. page 4 Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 Q45BW22 Series Infrared, 880 nm and Visible Red, 650 nm These models are an excellent choice for glass fiber optic applications where faster sensor response is not important. Their high excess gain means that opposed individual fibers can operate reliably in many very hostile environments. Also, special miniature bifurcated fiber optic assemblies with bundle sizes as small as .5 mm (.020") dia. may be used successfully for diffuse-mode sensing when using sensor model Q45BW22F(Q). For more information on compatible glass fiber optics, refer to your current Banner Photoelectric Sensors catalog. Q45BW22 Series Glass Fiber-Optic Models Models Range Cable Supply Voltage Output Type Excess Gain Diffuse mode performance based on 90% reflectance white test card Infrared, 880 nm 1000 E X C E S S G A I N Q45BW22F Q45BW22FQ Q45BW22FQ1 Range varies by sensing mode and fiber optics used Q45F 90 to 250V ac SPST Solid-state Relay 4-Pin Micro-style QD Q45F 150 mm 6.0 in Opposed Mode Opposed Mode 100 mm 100 4.0 in IT23S Fibers 50 mm 0 IT23S Fibers 10 IT13S Fibers 2.0 in 0 IT13S Fibers 50 mm 2.0 in 100 mm 4.0 in 150 mm 6.0 in 0 1 0.01 m 0.03 ft 3-wire 2 m (6.5') 3-Pin Mini-style QD Beam Pattern 0.1 m 0.33 ft 1.0 m 3.3 ft 0.4 m 15 in 0.8 m 30 in 10 m 33 ft 1.2 m 45 in 1.6 m 60 in 2.0 m 75 in DISTANCE DISTANCE 1000 E X C E S S G A I N Q45F Diffuse Mode Q45F BP Q45F opp.eps 0.15 in Diffuse Mode 0.10 in 3.8 mm 2.5 mm 100 BT13S Fiber 1.3 mm 0.05 in BT23S Fiber 0 BT23S Fiber 10 BT13S Fiber 1 1 mm 0.04 in 0.05 in 2.5 mm 0.10 in 3.8 mm 0.15 in 0 10 mm 0.4 in 100 mm 4.0 in 0 1.3 mm 25 mm 1 in 1000 mm 40 in 50 mm 2 in 75 mm 100 mm 125 mm 3 in 4 in 5 in DISTANCE DISTANCE Visible Red, 650 nm 1000 E X C E S S Q45FV Q45FV 30 mm Opposed Mode 100 Range varies by sensing Q45BW22FVQ mode and fiber Q45BW22FVQ1 optics used Q45BW22FV 10 mm 0.4 in 0 IT23S Fibers 3-Pin Mini-style QD 4-Pin Micro-style QD 10 0 90 to 250V ac SPST Solid-state Relay 0.8 in 30 mm 1.2 in 0 10 mm 0.4 in 100 mm 4 in 100 mm 150 mm 200 mm 250 mm 300 mm 4 in 6 in 8 in 10 in 12 in 1000 mm 40 in DISTANCE DISTANCE 1000 E X C E S S G A I N Q45FV Diffuse Mode Q45FV 3.0 mm 0.08 in 1.0 mm 0.04 in BT13S Fiber 0 0 1.0 mm 10 BT13S Fiber 0.04 in BT23S Fiber 2.0 mm 0.12 in 0 10 mm 0.4 in 100 mm 4.0 in DISTANCE 0.08 in 3.0 mm BT23S Fiber 1000 mm 40 in 0.12 in Diffuse Mode 2.0 mm 100 1 1 mm 0.04 in Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 0.4 in IT13S Fibers 20 mm IT13S Fibers 1 1.0 mm 0.04 in 3-wire 2 m (6.5') 0.8 in IT23S Fibers 10 mm G A I N 1.2 in Opposed Mode 20 mm 5 mm 0.2 in 10 mm 0.4 in 15 mm 0.6 in 20 mm 0.8 in 25 mm 1.0 in DISTANCE page 5 Q45BW22 Series Lower in cost than glass fiber optics, plastic fiber optics are ideal for use in situations where environmental conditions allow (for example, low levels of acids, alkalis, and solvents). Most are easily cut to length in the field, and are available in a variety of sensing end styles. For more information on compatible plastic fiber optics, refer to your current Banner Photoelectric Sensors catalog. Visible red, 660 nm Q45BW22 Series Plastic Fiber-Optic Models Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 E X C E S S Q45FP 100 Q45BW22FP Q45BW22FPQ Q45BW22FPQ1 Range varies by sensing mode and fiber optics used 3-wire 2 m (6.5') 3-Pin Mini-style QD 90 to 250V ac 4-Pin Micro-style QD 1.2 in PIT46U Fibers 0.6 in 0 0 PIT26U Fibers 10 15 mm 0.6 in 30 mm 1.2 in 1.8 in 45 mm PIT26U Fibers 0 1 1 mm 0.04 in SPST Solid-state Relay 1.8 in Opposed Mode 30 mm 15 mm PIT46U Fibers G A I N Q45FP 45 mm Opposed Mode 10 mm 0.4 in 100 mm 4.0 in 25 mm 1.0 in 50 mm 2.0 in 1000 mm 40 in 75 mm 100 mm 125 mm 3.0 in 4.0 in 5.0 in DISTANCE DISTANCE 1000 E X C E S S G A I N Q45FP Q45FP 18 mm Diffuse Mode PBT46U Fiber 0.75 in Diffuse Mode 12 mm 100 0.50 in PBT46U Fiber 6 mm 0.25 in 0 10 0 6 mm 0.25 in 12 mm 0.50 in 18 mm PBT26U Fiber 1 0.1 mm 0.004 in 1 mm 0.04 in 0.75 in 0 10 mm 0.4 in 100 mm 4 in 10 mm 0.4 in 20 mm 0.8 in 30 mm 1.2 in 40 mm 1.6 in 50 mm 2.0 in DISTANCE NOTES: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g., Q45BW22FP W/30) ii) A model with a QD connector requires a mating cable; see page 10. page 6 Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 Q45BW22 Series Q45BW22 Series Specifications Supply Voltage and Current 90 to 250V ac (50 - 60 Hz). Average current 20 mA. Peak current 500 mA at 120C ac, 750 mA at 250V ac Supply Protection Circuitry Protected against transient voltages. Output Configuration Short circuit/overload protected FET solid-state relay Output Rating Continuous current: 300 mA max. to 50 C (derate to 200 mA at 70C, 5 mA/C) Inrush current: 3A max. for 100 milliseconds, 5A max. for 1 millisecond Off-state leakage current: <100 microamps Saturation voltage: <3V at 200 mA Output Protection Circuitry Manually-resettable output latch-out trips in the event of an output overload or short circuit condition. The green Power LED flashes to indicate the latch-out. To reset the output, remove power to the sensor and load for 5 seconds, then restore power. Output Response Time Opposed mode: 2 milliseconds ON, 1 millisecond OFF All other sensing modes: 2 milliseconds ON/OFF (NOTE: 100 millisecond delay on power-up. Output is non-conducting during this time.) Repeatability Opposed mode: 0.25 milliseconds All other sensing modes: 0.5 milliseconds Response time and repeatability specifications are independent of signal strength. Adjustments Beneath sensor's transparent cover: Light/Dark Operate select switch; and multi-turn Sensitivity control (allows precise sensitivity setting - turn clockwise to increase gain). Optional logic and logic/display modules have adjustable timing functions (see page 10). Indicators Indicator LEDs are clearly visible beneath a raised transparent Lexan(R) dome on top of the sensor. Power (green) LED lights whenever 90 to 250V ac power is applied, and flashes to indicate output overload or output short circuit Signal (red) AIDTM System LED lights whenever the sensor sees its modulated light source, and pulses at a rate proportional to the strength of the received light signal Load (yellow) LED lights whenever the output relay is energized Optional 7-element LED signal strength display module Construction Molded reinforced thermoplastic polyester housing, o-ring-sealed transparent Lexan(R) cover, molded acrylic lenses, and stainless steel hardware. Q45s are designed to withstand 1200 psi washdown. The base of cabled models has a 1/2" NPS integral internal conduit thread. Environmental Rating NEMA 6P, IEC IP67 Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables, or 3-pin Mini-style ("Q" suffix models) or 4-pin Micro-style ("Q1" suffix models) quick-disconnect (QD) fittings are available. QD cables are ordered separately. See page 10. Operating Conditions Temperature: -40 to +70 C (-40 to +158F) Maximum relative humidity: 90% at 50C (non-condensing) Application Notes Optional output timing modules are available. See page 10 for more information. Certifications R Lexan(R) is a registered trademark of General Electric Co. Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 page 7 Q45BW22 Series Q45BW22 Series Dimensions Opposed, Retro, and Diffuse Sensing Modes (model suffix E, R, D, DL, DX, LP & LV) Mini-style Quick-disconnect Cabled 54.1 mm* (2.13") Micro-style Quick-disconnect *57.9 mm (2.28") for LP models 44.5 mm (1.75") Lens Centerline 50.8 mm (2.00") 69.0 mm (2.72") 6.4 mm (0.25") 87.6 mm (3.45") 4.5 mm (#10) Screw Clearance (2) 7.1 mm (0.28") 30.0 mm (1.18") Internal Thread (1/2-14NPSM) External Thread M30 X 1.5 o 6.1 (0.24") 2m (6.5') Cable External Thread M30 X 1.5 14 mm (0.6") Mounting Nut is Supplied Convergent Sensing Mode (model suffix CV & CV4) Glass Fiber Optic (model suffix F and FV) 60.5 mm (2.38") 61.7 mm (2.43") Mini-style QD Connector 15 mm (0.6") Micro-style QD Connector Plastic Fiber Optic (model suffix FP) 59.8 mm (2.35") Lens Centerline 50.8 mm (2.00") page 8 Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 Q45BW22 Series Q45BW22 Series Indicators and Controls Status indicator LEDs for Power, Signal and Output are clearly visible beneath a raised dome in the sensor's transparent o-ring-sealed Lexan(R) cover. The Power indicator lights whenever power is applied to the sensor. The Signal LED lights whenever the sensor sees its modulated light source, and pulses at a rate proportional to the strength of the received light signal; this is the AIDTM Alignment Indicating Device*. The Output indicator lights whenever the sensor's output relay is energized. This indicator is especially useful when a timing logic module is used and Signal and Output conditions are not concurrent. Also located beneath the sensor's o-ring-sealed cover are controls for light/dark operate selection and Sensitivity adjustment. Figure 1. Indicators and controls on the Q45BW22 Series Sensors * US patent no. 4356393 Q45BW22 Series Hookups Q45BW22 Sensors with Attached Cable Q45BW22 Sensors with Quick-Disconnect 3-Pin Mini-Style (model suffix Q) bn bu bk rd/bk bn 90-250V ac 90-250V ac bu bk Load Q45BW22 Sensors with Quick-Disconnect 4-Pin Micro-Style (model suffix Q1) rd Load 90-250V ac rd/wh Load gn Q452E Emitter with Attached Cable Q452E Emitter with Quick-Disconnect 3-Pin Mini-Style (model suffix Q) rd/bk bn bn 90 - 250V ac bu bu bk Q452E Emitter with Quick-Disconnect 4-Pin Micro-Style (model suffix Q1) 90 - 250V ac rd/wh 90-250V ac rd gn Quick Disconnect (QD) Option AC Q45BW22 Series sensors are sold with either a 2 m (6.5') or a 9 m (30') PVC-covered unterminated cable, or with a 3-pin Mini-style or 4-pin Micro-style QD cable fitting. AC 3-pin Mini-style QD sensors are identified by the letter "Q" in their model number suffix and 4-pin Micro-style are identified by "Q1". Mating cables for QD Q45BW22 sensors are specified on page 10. Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 page 9 Q45BW22 Series Accessories Quick-Disconnect Cables Cable: PVC jacket, polyurethane connector body; nylon coupling nut (Mini), chrome-plated brass coupling nut (Micro) Conductors: 18 AWG (Mini), 22 or 20 AWG (Micro) high-flex stranded, PVC insulation, gold plated contacts Temperature: -40 to +80C (-40 to +176F) Style Model Length 3-Pin Mini-style Female Pin-out Straight MBCC-306 MBCC-312 MBCC-330 2 m (6.5') 4 m (12') 9 m (30') 4-Pin Micro-style Female Pin-out Straight MQAC-406 MQAC-415 MQAC-430 2 m (6.5') 5 m (15') 9 m (30') Dimensions 61 mm max. (2.4") Pin-Out (Female View) 7/8-16UN-2B Black Wire o28 mm max. (1.1") Blue Wire o15 mm (0.6") Brown Wire Green Wire Red Wire 44 mm max. (1.7") Red/White Wire o1/2-20UNF-2B Red/Black Wire Retroreflective Targets Banner offers a wide selection of high-qualitity retroreflective targets. See the Accessories section of your current Banner Photoelectric Sensors catalog for complete information. NOTE: Polarized sensors require corner cube type retroreflective targets only. Non-polarized sensors may use any retroreflective target. Output Timing Logic and Signal Strength Display Modules Q45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a seven-element display which gives a more precise indication of excess gain than does the AIDTM system LED that is standard on Q45 sensors. The modules listed below may be used with all Q45VR2 sensors. See the data sheet packed with the module for more information. Model 45LM58 45LM58D 45LMD page 10 Logic and/or Display Function Programmable output timing logic Programmable output timing logic plus signal strength display Signal strength display only (no timing function) Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 Q45BW22 Series Mounting Brackets Model Description Dimensions 56.0 mm (2.20") SMB30C * 30 mm split clamp, black PBT bracket 13 mm (0.5") 63.0 mm (2.48") * Stainless steel mounting hardware included 31.5 mm (1.24") 13.5 mm (0.53") Nut Plate 2.5 mm (0.10") 45.0 mm (1.77") M5 x 0.8 x 80 mm Screw (2) 25.4 mm (1.00") 6.4 mm (0.25") o 30.15 mm (1.187" dia.) 57.0 mm (2.25") SMB30MM * 30 mm, 11-gauge, stainless steel bracket with curved mounting slots for versatility and orientation * Clearance for M6 (1/4") hardware 25.4 mm (1.00") 7.1 mm .28 x 90 (2 Slots) 34.9 mm (1.38") 25.4 mm (1.00") o 5.1 mm (0.20" dia.) o 6.4 mm (0.25" dia.) 57.2 mm (2.25") 25.4 mm (1.00") R 25.4 mm (1.00") 35.1 mm 57.2 mm (1.38") (2.25") 69.9 mm (2.75") 50.8 mm (2.00") SMB30SC 12.7 mm (0.50") * 30 mm swivel, black PBT bracket * Stainless steel mounting hardware included 58.7 mm (2.31") 30.0 mm (1.18") 66.5 mm (2.62") Banner Engineering Corp. * Minneapolis, MN U.S.A. www.bannerengineering.com * Tel: 763.544.3164 29.0 mm (1.14") page 11 Q45BW22 Series Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. ! WARNING . . . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. p/n 37209 Rev. E Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 * Phone: 763.544.3164 * www.bannerengineering.com * Email: sensors@bannerengineering.com