Q45BW22 Series Sensors
90 to 250V ac photoelectric sensors with protected solid-state relay output
Printed in USA 04/01 P/N 37209 rev. D
NOTES: i) 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q452E W/30)
ii) A model with a QD connector requires a mating cable; see page 10.
Q45BW22 Series Features
•Advanced one-piece photoelectric sensors with outstanding optical
performance and extremely rugged design
•90 to 250V ac
•Protected solid-state relay output; 300 mA max. load at up to 250V ac
•Multiple sensing modes include: opposed, diffuse, retroreflective and
convergent, plus glass and plastic fiber optic models
•Switchable light/dark operate
•Versatile plug-in modules available for output timing logic and/or signal
strength display
•Highly visible Power, Signal (AID™ System*), and Output indicator LEDs
•Choice of prewired 2 m (6.5') or 9 m (30') unterminated cable, plus Mini-style
or Micro-style quick-disconnect fittings
•Versatile mounting options
•Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and IEC IP67
rating
IMPORTANT: SEE SAFETY USE WARNING ON BACK PAGE
Q45BW22 Series Opposed-Mode Emitter (E) and Receiver (R) Models
Q452E Emitter
Q45BW22R Receiver
Models Range Cable Supply
Voltage
Output
Type Excess Gain
60 m
(200')
2-wire 2m (6.5')
3-wire 2m (6.5')
90 to
250V ac
SPST
Solid-
state
Relay
Because of their extremely high excess gain, these opposed-mode sensors are an
excellent option for sensing in contaminated or dirty areas, and are also the best
choice for long-range sensing. Infrared, 880 nm
Q452EQ Emitter
Q452EQ1 Emitter
Q45BW22RQ Receiver
Q45BW22RQ1 Receiver
3-Pin Mini-style QD
4-Pin Micro-style QD
3-Pin Mini-style QD
4-Pin Micro-style QD
Beam Pattern
1
10
100
1.0 m
3.3 ft
10 m
33 ft
100 m
330 ft
0.1 m
0.33 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
1000
Q45E/R
Opposed Mode
48 m
160 ft
60 m
200 ft
36 m
120 ft
24 m
80 ft
12 m
40 ft
0
0
0.5 m
1.0 m
1.5 m
0.5 m
1.0 m
1.5 m
0
20 in
40 in
60 in
20 in
40 in
60 in
DISTANCE
Q45E/R
Opposed Mode
Effective Beam: 13 mm
*U.S. Patent no. 4356393
R
E
Aug 2013
Q45BW22 Series
page 2
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
NOTES:
i) 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45BW22LV W/30)
ii) A model with a QD connector requires a mating cable; see page 10.
Models Range Cable
Supply
Voltage
Output
Type Excess Gain Beam Pattern
Non-Polarized
1
10
100
1000
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
.01 m
.033 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45LV
Retroreflective Mode
With BRT-3 Reflector
12 m
40 ft
15 m
50 ft
9 m
30 ft
6 m
20 ft
3 m
10 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Q45LV
Retroreflective Mode
With BRT-3 Reflector
Polarized
1
10
100
1000
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
.01 m
.033 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45LP
Retroreflective Mode
With BRT-3 Reflector
6 m
20 ft
7.5 m
25 ft
4.5 m
15 ft
3 m
10 ft
1.5 m
5 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Q45LP
Retroreflective
Mode
With BRT-3 Reflector
Q45BW22LP
Q45BW22LPQ
Q45BW22LPQ1
0.15 to 6 m
(6" to 20')
Q45BW22LV
Q45BW22LVQ
Q45BW22LVQ1
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
0.08 to 9 m
(3" to 30')
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
Q45BW22 Series Retroreflective-Mode Models
The visible red sensing beam of these sensors makes them very easy to align.
Model Q45BW22LP polarizes the emitted light and filters out unwanted reflections,
making sensing possible in applications otherwise considered unsuited to
retroreflective sensing. Performance is specified using the model BRT-3 3"
reflector (see the Accessories section of your current Banner Photoelectric Sensors
catalog for further information). Visible red, 680 nm
Non-Polarized Polarized
P
Q45BW22 Series
page 3
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45BW22 Series Diffuse-Mode Models
500 mm
20.0 in
400 mm
16.0 in
300 mm
12.0 in
200mm
8.0 in
100 mm
4.0 in
0
0
5 mm
10 mm
15 mm
5 mm
10 mm
15 mm
0
0.2 in
0.4 in
0.6 in
0.2 in
0.4 in
0.6 in
DISTANCE
Q45D
Diffuse Mode
Models Range Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Short Range
Q45BW22DL
Q45BW22DLQ
Q45BW22DLQ1
1. 8 m
(6')
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1.0 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45D
Diffuse Mode
2.4 m
8 ft
3.0 m
10 ft
1.8 m
6 ft
1.2 m
4 ft
0.6 m
2 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Q45DL
Diffuse Mode
Long Range
Q45BW22DX
Q45BW22DXQ
Q45BW22DXQ1
3 m
(10')
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
1
10
100
1000
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
.01 m
.033 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45DL
Diffuse Mode
Q45BW22D
Q45BW22DQ
Q45BW22DQ1
45 cm
(18")
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
Performance based on 90% reflectance white test card
SPST
Solid-state
Relay
90 to
250V ac
3.0 m
10 ft
2.4 m
8 ft
1.8 m
6 ft
1.2 m
4 ft
0.6 m
2 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Diffuse Mode
Q45DX
High Power
1
10
100
0.1 m
0.33 ft
1.0 m
3.3 ft
10 m
33 ft
0.01 m
0.033 ft
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45DX
Diffuse Mode
SPST
Solid-state
Relay
Infrared, 880 nm
These diffuse-mode models detect objects by sensing the reflection of their own emitted light.
Ideal for use when the reflectivity and profile of the object to be sensed are sufficient to return a
large percentage of emitted light back to the sensor. Model Q45BW22DX is the first choice for
diffuse-mode applications when there are no background objects to falsely return light.
Q45BW22 Series
page 4
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
NOTES:
i) 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45BW22CV W/30)
ii) A model with a QD connector requires a mating cable; see page 10.
Visible red, 680 nm
These sensors are ideal for reflective sensing of very small parts or profiles, and can accurately
sense the position of parts approaching from the side. Will ignore all but highly reflective objects
that are outside the sensing range.
Q45BW22 Series Convergent-Mode Models
190 mm
7.5 in
150 mm
6.0 in
113 mm
4.5 in
75 mm
3.0 in
38 mm
1.5 in
0
0
1.2 mm
2.5 mm
3.8 mm
1.2 mm
2.5 mm
3.8 mm
0
0.05 in
0.10 in
0.15 in
0.05 in
0.10 in
0.15 in
DISTANCE
Q45CV
Convergent Mode
Models Focus Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Q45BW22CV
Q45BW22CVQ
Q45BW22CVQ1
38 mm
(1.5")
Spot Size
at Focus:
1.3 mm
(0.05")
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
1
10
100
10 mm
.4 in
100 mm
4 in
1000 mm
40 in
1 mm
.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45CV
Convergent Mode
190 mm
7.5 in
150 mm
6.0 in
113 mm
4.5 in
75 mm
3.0 in
38 mm
1.5 in
0
0
1.2 mm
2.5 mm
3.8 mm
1.2 mm
2.5 mm
3.8 mm
0
0.05 in
0.10 in
0.15 in
0.05 in
0.10 in
0.15 in
DISTANCE
Q45CV4
Convergent Mode
Q45BW22CV4
Q45BW22CV4Q
Q45BW22CV4Q1
100 mm
(4")
Spot Size
at Focus:
1.5 mm
(0.06")
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
1
10
100
10 mm
.4 in
100 mm
4 in
1000 mm
40 in
1 mm
.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45CV4
Convergent Mode
Performance based on 90% reflectance white test card
1
10
100
10 mm
0.4 in
100 mm
4 in
1000 mm
40 in
1.0 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45FV
Opposed Mode
IT23S Fibers
IT13S Fibers
300 mm
12 in
250 mm
10 in
200 mm
8 in
150 mm
6 in
100 mm
4 in
0
0
10 mm
20 mm
30 mm
10 mm
20 mm
30 mm
0
0.4 in
0.8 in
1.2 in
0.4 in
0.8 in
1.2 in
DISTANCE
Q45FV
Opposed Mode
IT23S Fibers
IT13S Fibers
2.0 m
75 in
1.6 m
60 in
1.2 m
45 in
0.8 m
30 in
0.4 m
15 in
0
0
50 mm
100 mm
150 mm
50 mm
100 mm
150 mm
0
2.0 in
4.0 in
6.0 in
2.0 in
4.0 in
6.0 in
DISTANCE
Q45F
Opposed Mode
IT23S Fibers
IT13S Fibers
BP Q45F opp.eps
page 5
Q45BW22 Series
These models are an excellent choice for glass fiber optic applications where
faster sensor response is not important. Their high excess gain means that
opposed individual fibers can operate reliably in many very hostile environments.
Also, special miniature bifurcated fiber optic assemblies with bundle sizes as
small as .5 mm (.020") dia. may be used successfully for diffuse-mode sensing
when using sensor model Q45BW22F(Q). For more information on compatible
glass fiber optics, refer to your current Banner Photoelectric Sensors catalog.
Q45BW22 Series Glass Fiber-Optic Models
Models Range Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Infrared, 880 nm
1
10
100
0.1 m
0.33 ft
1.0 m
3.3 ft
10 m
33 ft
0.01 m
0.03 ft
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45F
Opposed Mode
IT23S Fibers
IT13S Fibers
Diffuse mode performance based on 90% reflectance white test card
Q45BW22F
Q45BW22FQ
Q45BW22FQ1
Range
varies by
sensing
mode and
fiber
optics
used
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
Infrared, 880 nm and Visible Red, 650 nm
Q45BW22FV
Q45BW22FVQ
Q45BW22FVQ1
Range
varies by
sensing
mode and
fiber
optics
used
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
Visible Red, 650 nm
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45F
Diffuse Mode
BT23S Fiber
BT13S Fiber
125 mm
5 in
100 mm
4 in
75 mm
3 in
50 mm
2 in
25 mm
1 in
0
0
1.3 mm
2.5 mm
3.8 mm
1.3 mm
2.5 mm
3.8 mm
0
0.05 in
0.10 in
0.15 in
0.05 in
0.10 in
0.15 in
DISTANCE
Q45F
Diffuse Mode
BT23S Fiber
BT13S Fiber
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45FV
Diffuse Mode
BT23S Fiber
BT13S
Fiber
25 mm
1.0 in
20 mm
0.8 in
15 mm
0.6 in
10 mm
0.4 in
5 mm
0.2 in
0
0
1.0 mm
2.0 mm
3.0 mm
1.0 mm
2.0 mm
3.0 mm
0
0.04 in
0.08 in
0.12 in
0.04 in
0.08 in
0.12 in
DISTANCE
Q45FV
Diffuse Mode
BT23S Fiber
BT13S Fiber
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45BW22 Series
page 6
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
NOTES:
i) 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45BW22FP W/30)
ii) A model with a QD connector requires a mating cable; see page 10.
Visible red, 660 nm
Lower in cost than glass fiber optics, plastic fiber optics are ideal for use in
situations where environmental conditions allow (for example, low levels of
acids, alkalis, and solvents). Most are easily cut to length in the field, and are
available in a variety of sensing end styles. For more information on compatible
plastic fiber optics, refer to your current Banner Photoelectric Sensors catalog.
Q45BW22 Series Plastic Fiber-Optic Models
Models Range Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Q45BW22FP
Q45BW22FPQ
Q45BW22FPQ1
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45FP
Opposed Mode
PIT46U Fibers
PIT26U Fibers
125 mm
5.0 in
100 mm
4.0 in
75 mm
3.0 in
50 mm
2.0 in
25 mm
1.0 in
0
0
15 mm
30 mm
45 mm
15 mm
30 mm
45 mm
0
0.6 in
1.2 in
1.8 in
0.6 in
1.2 in
1.8 in
DISTANCE
Q45FP
Opposed Mode PIT46U Fibers
PIT26U Fibers
Diffuse mode performance based on 90% reflectance white test card
Range
varies by
sensing
mode
and fiber
optics
used
3-wire 2 m (6.5')
3-Pin Mini-style QD
4-Pin Micro-style QD
90 to
250V ac
SPST
Solid-state
Relay
1
10
100
1 mm
0.04 in
10 mm
0.4 in
100 mm
4 in
0.1 mm
0.004 in
1000
E
X
C
E
S
S
G
A
I
N
Q45FP
Diffuse Mode
PBT46U Fiber
PBT26U Fiber 50 mm
2.0 in
40 mm
1.6 in
30 mm
1.2 in
20 mm
0.8 in
10 mm
0.4 in
0
0
6 mm
12 mm
18 mm
6 mm
12 mm
18 mm
0
0.25 in
0.50 in
0.75 in
0.25 in
0.50 in
0.75 in
DISTANCE
Q45FP
Diffuse Mode
PBT46U Fiber
Q45BW22 Series
page 7
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45BW22 Series Specifications
Supply Voltage and Current 90 to 250V ac (50 - 60 Hz). Average current 20 mA. Peak current 500 mA at 120C ac, 750 mA at 250V ac
Supply Protection Circuitry Protected against transient voltages.
Output Configuration Short circuit/overload protected FET solid-state relay
Output Rating Continuous current: 300 mA max. to 50° C (derate to 200 mA at 70°C, 5 mA/°C)
Inrush current: 3A max. for 100 milliseconds, 5A max. for 1 millisecond
Off-state leakage current: <100 microamps
Saturation voltage: <3V at 200 mA
Output Protection Circuitry Manually-resettable output latch-out trips in the event of an output overload or short circuit condition. The
green Power LED flashes to indicate the latch-out. To reset the output, remove power to the sensor and load
for 5 seconds, then restore power.
Output Response Time Opposed mode: 2 milliseconds ON, 1 millisecond OFF
All other sensing modes: 2 milliseconds ON/OFF
(NOTE: 100 millisecond delay on power-up. Output is non-conducting during this time.)
Repeatability Opposed mode: 0.25 milliseconds
All other sensing modes: 0.5 milliseconds
Response time and repeatability specifications are independent of signal strength.
Adjustments Beneath sensor’s transparent cover: Light/Dark Operate select switch; and multi-turn Sensitivity control
(allows precise sensitivity setting – turn clockwise to increase gain). Optional logic and logic/display
modules have adjustable timing functions (see page 10).
Indicators Indicator LEDs are clearly visible beneath a raised transparent Lexan®dome on top of the sensor.
Power (green) LED lights whenever 90 to 250V ac power is applied, and flashes to indicate output overload
or output short circuit
Signal (red) AID™ System LED lights whenever the sensor sees its modulated light source, and pulses at a
rate proportional to the strength of the received light signal
Load (yellow) LED lights whenever the output relay is energized
Optional 7-element LED signal strength display module
Construction Molded reinforced thermoplastic polyester housing, o-ring-sealed transparent Lexan®cover, molded acrylic
lenses, and stainless steel hardware. Q45s are designed to withstand 1200 psi washdown. The base of
cabled models has a 1/2" NPS integral internal conduit thread.
Environmental Rating NEMA 6P, IEC IP67
Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables, or 3-pin Mini-style (“Q” suffix models) or 4-pin Micro-style
(“Q1” suffix models) quick-disconnect (QD) fittings are available. QD cables are ordered separately.
See page 10.
Operating Conditions Temperature: -40° to +70° C (-40° to +158°F)
Maximum relative humidity: 90% at 50°C (non-condensing)
Application Notes Optional output timing modules are available. See page 10 for more information.
Lexan®is a registered trademark of General Electric Co.
Certifications
R
Q45BW22 Series
page 8
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Convergent Sensing Mode
(model suffix CV & CV4)
Glass Fiber Optic
(model suffix F and FV)
61.7 mm
(2.43")
50.8 mm
(2.00")
Lens
Centerline
60.5 mm
(2.38")
59.8 mm
(2.35")
Plastic Fiber Optic
(model suffix FP)
Q45BW22 Series Dimensions
54.1 mm*
(2.13")
44.5 mm
(1.75")
69.0 mm
(2.72")
87.6 mm
(3.45")
Internal Thread
(1/2–14NPSM)
External Thread
M30 X 1.5
30.0 mm
(1.18")
ø 6.1 (0.24")
2m (6.5') Cable
7.1 mm
(0.28")
4.5 mm (#10) Screw
Clearance (2)
50.8 mm
(2.00")
6.4 mm (0.25")
Lens Centerline
Mounting Nut is Supplied
*57.9 mm (2.28") for LP models
Opposed, Retro, and Diffuse Sensing Modes
(model suffix E, R, D, DL, DX, LP & LV)
Cabled
External Thread
M30 X 1.5
Mini-style QD Connector
14 mm (0.6")
Mini-style Quick-disconnect
15 mm (0.6") Micro-style
QD Connector
Micro-style Quick-disconnect
Q45BW22 Series
page 9
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45BW22 Series Indicators and Controls
Status indicator LEDs for Power, Signal and Output are clearly visible
beneath a raised dome in the sensor’s transparent o-ring-sealed Lexan®
cover. The Power indicator lights whenever power is applied to the sensor.
The Signal LED lights whenever the sensor sees its modulated light
source, and pulses at a rate proportional to the strength of the received
light signal; this is the AID™ Alignment Indicating Device*. The Output
indicator lights whenever the sensor’s output relay is energized. This
indicator is especially useful when a timing logic module is used and
Signal and Output conditions are not concurrent.
Also located beneath the sensor’s o-ring-sealed cover are controls for
light/dark operate selection and Sensitivity adjustment.
* US patent no. 4356393
Figure 1. Indicators and controls on the Q45BW22
Series Sensors
Q45BW22 Sensors with Attached Cable Q45BW22 Sensors with Quick-Disconnect
3-Pin Mini-Style (model suffix Q)
Q45BW22 Sensors with Quick-Disconnect
4-Pin Micro-Style (model suffix Q1)
Q452E Emitter with Attached Cable
bn
bk
bu 90-250V ac
Load
bn
bk
bu 90-250V ac
Load
rd/bk
rd
rd/wh
gn
90-250V ac
Load
bn
bu
90 - 250V ac
Q452E Emitter with Quick-Disconnect
3-Pin Mini-Style (model suffix Q)
Q452E Emitter with Quick-Disconnect
4-Pin Micro-Style (model suffix Q1)
bn
bk
bu 90 - 250V ac
rd/bk
rd
rd/wh
gn
90-250V ac
Q45BW22 Series Hookups
Quick Disconnect (QD) Option
AC Q45BW22 Series sensors are sold with either a 2 m (6.5') or a 9 m (30') PVC-covered unterminated cable, or with a 3-pin
Mini-style or 4-pin Micro-style QD cable fitting.
AC 3-pin Mini-style QD sensors are identified by the letter “Q” in their model number suffix and 4-pin Micro-style are identified
by “Q1”. Mating cables for QD Q45BW22 sensors are specified on page 10.
Q45BW22 Series
page 10
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Accessories
Retroreflective Targets
Banner offers a wide selection of high-qualitity retroreflective targets. See the Accessories
section of your current Banner Photoelectric Sensors catalog for complete information.
NOTE: Polarized sensors require corner cube type retroreflective targets only. Non-polarized
sensors may use any retroreflective target.
45LM58
45LM58D
45LMD
Programmable output timing logic
Programmable output timing logic plus signal strength display
Signal strength display only (no timing function)
Q45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a seven-element
display which gives a more precise indication of excess gain than does the AID™ system LED that is standard on Q45 sensors. The modules
listed below may be used with all Q45VR2 sensors. See the data sheet packed with the module for more information.
Model Logic and/or Display Function
Output Timing Logic and Signal Strength Display Modules
Quick-Disconnect Cables
4-Pin
Micro-style
Female
Pin-out
Straight
MQAC-406
MQAC-415
MQAC-430
2 m (6.5')
5 m (15')
9 m (30')
Cable: PVC jacket, polyurethane connector body; nylon coupling nut (Mini), chrome-plated brass coupling nut (Micro)
Conductors: 18 AWG (Mini), 22 or 20 AWG (Micro) high-flex stranded, PVC insulation, gold plated contacts
Temperature: -40° to +80°C (-40° to +176°F)
ø1/2-20UNF-2B
ø15 mm
(0.6")
44 mm max.
(1.7")
Green Wire
Red/Black
Wire
Red/White
Wire
Red Wire
3-Pin
Mini-style
Female
Pin-out
Straight
MBCC-306
MBCC-312
MBCC-330
2 m (6.5')
4 m (12')
9 m (30')
7/8-16UN-2B
ø28 mm max.
(1.1")
61 mm max.
(2.4")
Style
Brown Wire
Blue Wire
Black Wire
Model Length Dimensions Pin-Out (Female View)
Q45BW22 Series
page 11
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Mounting Brackets
Model Description Dimensions
56.0 mm
(2.20")
63.0 mm
(2.48")
13.5 mm (0.53")
45.0 mm
(1.77")
2.5 mm
(0.10")
31.5 mm
(1.24")
Nut Plate
13 mm
(0.5")
M5 x 0.8 x 80 mm
Screw (2)
SMB30C • 30 mm split clamp, black PBT bracket
• Stainless steel mounting hardware included
50.8 mm
(2.00")
58.7 mm
(2.31")
66.5 mm
(2.62")
30.0 mm
(1.18")
29.0 mm
(1.14")
12.7 mm
(0.50")
SMB30SC • 30 mm swivel, black PBT bracket
• Stainless steel mounting hardware included
57.2 mm
(2.25")
57.2 mm
(2.25")
34.9 mm
(1.38")
ø 6.4 mm
(0.25" dia.)
ø 30.15 mm
(1.187" dia.)
25.4 mm
(1.00")
35.1 mm
(1.38")
25.4 mm
(1.00") ø 5.1 mm
(0.20" dia.)
25.4 mm
(1.00")
6.4 mm
(0.25")
25.4 mm
(1.00")
57.0 mm
(2.25")
69.9 mm
(2.75")
7.1 mm
.28 x 90° (2 Slots)
R 25.4 mm
(1.00")
SMB30MM
• 30 mm, 11-gauge, stainless steel bracket
with curved mounting slots for versatility
and orientation
• Clearance for M6 (1/4") hardware
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
Q45BW22 Series
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any
other warranty either expressed or implied.
WARNING . . . Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety
applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current
Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
!
p/n 37209 Rev. E
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment.
Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is
found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper
application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING,
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER
ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER
ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES,
LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT
LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.
