PXO TQDILAC Typical Applications Base Stations Test Equipment Synthesizers Features AT-Cut Crystal Dual-inline ACMOS-oscillator Hermetically Sealed Package Surface Mount Option Frequency range 8 MHz - 80 MHz Standard frequencies 10MHz; 16.384;19.44; 77.76 MHz Frequency stabilities Parameter vs. operating temperature range Parameter Initial tolerance Code III Frequency stability Operating temp range 34 32 10 12 14 16 18 37 29 15 ppm 10 ppm 50 ppm 20 ppm 10 ppm 7.5 ppm 5.0 ppm 10 ppm 5.0 ppm -40 ... +90C -30 ... +80C -20 ... +70C Code II Frequency stability Condition 01 02 03 05 07 100 ppm 50 ppm 20 ppm 10 ppm 5 ppm @ 25C 0 ... +50C RF output Parameter Signal Load Rise and Fall time Duty cycle Value Condition ACMOS 25pF 10% < 5ns 40/60 % @ 25pF & 10 to 90% @Vs/2 Value Condition Supply voltage Parameter Supply voltage (Vs) Current consumption 5.0 V 5 % < 60 mA Additional parameters Parameter Phase Noise Weight Operable temperature range Storage temperature range Processing & Packing Corning Frequency Control * Worldwide Data Book 2001 Value < - 80 dBc/Hz < - 110 dBc/Hz < - 135 dBc/Hz < -145 dBc/Hz < - 150 dBc/Hz <6g -40 ... +90C -60 ... +105C Condition 10 100 1 10 100 Hz Hz kHz kHz kHz Note 1 handling&processing note v1.1.2001-08-29 Corning Frequency Control Inc. * 100 Watts Street * Mt. Holly Springs, PA 17065 * Tel 1-717-486-3411 * Fax 1-717-486-5920 * www.corningfrequency.com Tele Quarz GmbH & Co. KG * Landstrasse * D-74924 Neckarbischofsheim, Germany * Tel +49-7268-801-0 * Fax +49-07268-801-281 * www.telequarz.de 1/2 PXO TQDILAC Enclosure Type Option I Case Blank A G125 G175 Condition Drawing 22,7max. 20,7max. G 125 15,240,3 8 14 8 1 7 H = 9,4; G175 Standard 15,1max. 10,9max. 13,1max. 14 4,58 0,5 7 7,62 0,3 12,20,5 1 G 175 18,5max. H = 7,5max.; G125 Standard 0,2 H Pin 1 corner 5,85min. 0,8max. H S Auflage flache o0,45 S 0,1 15,24 0,1 13,2 0,1 1,8 0,1 Pin Connections Pin Pin Pin Pin 1 7 8 14 all units in mm Tri-State Control or N.C. GND RF output Supply Voltage (Vs) Code I E Blank Ordering Code Code I Model Enable TQDILAC TQDILAC E Example: Order: Note 1 Code II Adjustment tolerance 05. Code III Frequency Stability 14. Pin 1 TriState Output Pin8 High Open Low Output clock High resistance output N.C. Option I Case Frequency A 30M00000 Typical values @ 10 MHz Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25C) Subject to technical modification; Not all options and codes are available at all Frequencies Corning Frequency Control * Worldwide Data Book 2001 v1.1.2001-08-29 Corning Frequency Control Inc. * 100 Watts Street * Mt. Holly Springs, PA 17065 * Tel 1-717-486-3411 * Fax 1-717-486-5920 * www.corningfrequency.com Tele Quarz GmbH & Co. KG * Landstrasse * D-74924 Neckarbischofsheim, Germany * Tel +49-7268-801-0 * Fax +49-07268-801-281 * www.telequarz.de 2/2