Curtis Industries
A Division of Powers Holdings, Inc.
www.curtisind.com Specifications subject to change.
Dimensions are shown for
reference purposes only.
16
SINGLE PHASE FILTERS
F1400 RFI Filters
Nominal
Current
Rating
Part
Number Termination
Line/Load
MINIMUM INSERTION LOSS - dB (50 ohm Circuit)
MODE Frequency - MHz
.15 .50 1.0 5.0 10 30
3A F1400AA03
F1400BB03
F1400CA03
QC/QC
Wire/Wire
IEC/QC
Common
Differential 58
40 65
60 65
65 65
65 60
65 44
60
6A F1400AA06
F1400BB06
F1400CA06
QC/QC
Wire/Wire
IEC/QC
Common
Differential 58
36 65
55 65
60 65
60 60
55 54
50
10A F1400AA10
F1400BB10 QC/QC
Wire/Wire
Common
Differential 56
40 65
50 65
60 65
65 60
65 54
60
Features:
• High Peak Current Design — High Insertion Loss for
Switching Power Supply Emissions
• Low-Leakage Current
• Compact Case Sizes in 6 and 10Amp Models
• Available with Integral IEC Connector in 3 and 6Amp
Models
F1400 Simplified Schematic
Specifications:
Rated Voltage: 250VAC Maximum - 50/60 Hz
Rated Current: 115VAC 250VAC
3A 1.5A
6A 4A
10A 6A
Current Overload: 6X for 8 seconds
Hi-Pot Test (1 min):
Line to Ground 1500VAC
Line to Line 1768VDC
Insulation Resistance: 9 x 109 Ω at 100VDC
Ambient Temperature: 40°C Max. at rated current
Humidity Range: 0% to 95% R.H.
Termination:
A: QC – Quick Connect
B: Wire
C: IEC Receptacle
Maximum Leakage Current:
Each Line to Ground F1400
115VAC, 60Hz: 0.25mA
250VAC, 50Hz: 0.40mA
Agency Approvals:
LINE
LOAD
L
G
N
L
N
NOTE: Other combinations of terminals may be specified on special order.
High Performance
Curtis Industries
A Division of Powers Holdings, Inc. 1-800-657-0853
Dimensions are in inches and millimeters
unless otherwise specified.
Values in parentheses are metric equivalents.
17
SINGLE PHASE FILTERS
F1400AA (3, 6 and 10Amp) Dimensions
F1400BB (3, 6 and 10Amp) Dimensions
F1400CA (3 and 6Amp) Dimensions
Amps A B C D E F
3A 3.310
(84,1)
2.000
(50,8)
1.500
(38,2)
2.940
(74,7)
2.500
(63,5)
.550
(14,0)
6A 3.310
(84,1)
2.000
(50,8)
1.500
(38,2)
2.940
(74,7)
2.500
(63,5)
.550
(14,0)
10A 4.70
(119,4)
2.250
(57,1)
1.750
(44,4)
4.250
(107,9)
3.750
(95,3)
.550
(14,0)
Amps A B C D E
3A 2.880
(73,1)
2.120
(53,8)
1.500
(38,1)
.550
(14,0)
.565
(14,3)
6A 2.880
(73,1)
2.120
(53,8)
1.500
(38,1)
.550
(14,0)
.565
(14,3)
Amps A B C D E
3A 3.310
(84,1)
2.000
(50,8)
1.500
(38,1)
2.940
(74,7)
2.500
(63,5)
6A 3.310
(84,1)
2.000
(50,8)
1.500
(38,1)
2.940
(74,7)
2.500
(63,5)
10A 4.70
(119,4)
2.250
(57,1)
1.750
(44,4)
4.250
(107,9)
3.750
(95,3)
L
I
N
E
L
O
A
D
L
I
N
E
L
O
A
D
L
I
N
E
L
O
A
D
C
.250 QC
(6,4)
.188 Dia.
(4,77)
2 Holes
B
A
D
E FF
A
B
D
E4.00
(101,6)
Min.
C
C
A
E
D
B
.250 QC
(6,4)
6-32 Tap
2-Places
.250±.062
(6,35) Typ.
No. 18
Gauge Wire
High Performance
Refer to Page 40
for Standard
Mounting Cutouts
(1) 5mm x 20mm Fuse (not included)
Curtis Industries
A Division of Powers Holdings, Inc.
www.curtisind.com Specifications subject to change.
Dimensions are shown for
reference purposes only.
40
SINGLE PHASE FILTERS
Standard Mounting Cutouts
F1200CA, F1300CA, F1400CA,
F1500CA, F1600CA, F1700CA F1500FA, F1600FA,
1.145
(29,08)
1.417
(36,0)
1.275
(32,39)
✱.09 R
(2,29)
.638
(16,21)
.140 Dia.
(3,55)
2 Holes
1.20
(30.5)
.90
(22,9)
1.575
(40,0)
.187
(4,75)
.450
(11,43)
.234
(5,94)
.140 Dia.
(3,55)
2 Holes
F1300CP, F1600CP
.062 Hole Dia.
(1,57)
5 Holes
1.500
(38,1)
.600
(15,2)
.700
(17,8)
1.400
(35,6)
N
L
F5500/5600/5700 SERIES
.140 Dia.
(3,55)
2 Holes
.234 R.
(5,94)
(Typ.)
1.575
(40,01)
1.20
(30,48)
.90
(22,8)
✱ for mounting
from back side
SERIES
PE = Power Entry
PM = Medical
Power Entry
LOAD
TERMINATION
A = Quick Connects
B = Wire Leads
D = Screw Terminals
(20 & 30 amp only)
P = Printed Circuit Pins
S = Solder T ab
LINE TERMINATION
A = Quick Connects
B = Wire Leads
C = IEC Connector
D = Screw Terminals
(20 & 30 amp only)
F = Fused IEC
P = Printed Circuit Pins
W = Dual Fused IEC
J = Switched IEC
How to Order
The Curtis part numbering system is made up of four
elements. Each element denotes a specific requirement
(mechanical or electrical) which, when properly
sequenced, fully identifies the required catalog filter. As
shown, the first five alpha/numeric characters denote
the series type; the sixth character (alpha) denotes the
type of line termination; the seventh character (alpha)
denotes the type of load termination; the last two
characters (numeric) denote the current rating.
Compose your part number as follows: Select the series
required, add two alpha character for the line and load
termination, followed by two numeric characters for
the required current rating. For example, F1100AB06
completely identifies an F1100 series filter with quick
connects on line side and wire leads on load side, with
a 6-amp rating.
F1100 X X X
CURRENT
RATING
01 = 1 Amp
03 = 3 Amps
06 = 6 Amps
10 = 10 Amps
15 = 15 Amps
20 = 20 Amps
30 = 30 Amps
