Specification of Automotive MLCC (Reference sheet) Supplier : Samsung electro-mechanics Samsung P/N : Product : Multi-layer Ceramic Capacitor CAP, 330, 25V, 10%, X7R, 0603 Description : AEC-Q 200 Specified CL10B334KA8VPNC A. Samsung Part Number Series CL 10 B 334 K A 8 V P N C Samsung Multi-layer Ceramic Capacitor 0603 (inch code) Size Dielectric X7R Capacitance 330 10 % Capacitance L: 25 V Thickness 0.8 0.1 W: mm 0.8 0.1 mm Termination Ni Soft termination Plating Sn 100% Inner electrode tolerance Rated Voltage 1.6 0.1 mm Product Automotive Grade code Packaging Standard (Pb Free) Cardboard Type, 7" reel B. Reliability Test and Judgement condition Performance Test condition High Temperature Appearance : No abnormal exterior appearance Unpowered, 1000hrs@T=150 Exposure Capacitance Change : Within 10% Measurement at 242hrs after test conclusion Tan : 0.075 max IR : More than 10,000 or 500x Whichever is Smaller Temperature Cycling Appearance : No abnormal exterior appearance 1000Cycles Capacitance Change : Within 10% Measurement at 242hrs after test conclusion Tan : 0.075 max 1 cycle condition : IR : More than 10,000 or 500x Whichever is Smaller Destructive Physical No Defects or abnormalities -55+0/-3(153min) -> Room Temp(1min.) -> 125+3/-0(153min) -> Room Temp(1min.) Per EIA 469 Analysis Moisture Resistance Appearance : No abnormal exterior appearance 10Cycles, t=24hrs/cycle Capacitance Change : Within 12.5% Heat (25~65) and humidity (80~98%), Unpowered Tan : 0.075max measurement at 242hrs after test conclusion IR : More than 10,000 or 500x Whichever is Smaller Humidity Bias Appearance : No abnormal exterior appearance 1000hrs 85/85%RH, Rated Voltate and 1.3~1.5V, Capacitance Change : Within 12.5% Add 100kohm resistor Tan : 0.075 max Measurement at 242hrs after test conclusion IR : More than 500 or 25x The charge/discharge current is less than 50mA. Whichever is Smaller High Temperature Appearance : No abnormal exterior appearance 1000hrs @ TA=125, 200% Rated Voltage, Operating Life Capacitance Change : Within 12.5% Measurement at 242hrs after test conclusion Tan : 0.075 max The charge/discharge current is less than 50mA. IR : More than 1000 or 50x Whichever is Smaller Performance External Visual No abnormal exterior appearance Physical DimensionsWithin the specified dimensions Mechanical Shock Test condition Microscope (10) Using The calipers Appearance : No abnormal exterior appearance Three shocks in each direction should be applied along Capacitance Change : Within 10% 3 mutually perpendicular axes of the test specimen (18 shocks) Tan , IR : initial spec. Vibration Peakvalue Duration Wave Velocity 1,500G 0.5ms Half sine 4.7m/sec. Appearance : No abnormal exterior appearance 5g's for 20min., 12cycles each of 3 orientations, Capacitance Change : Within 10% Use 8"x5" PCB 0.031" Thick 7 secure points on one long side Tan , IR : initial spec. and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10~2000. Resistance to Appearance : No abnormal exterior appearance Solder pot : 2605, 101sec. Solder Heat Capacitance Change : Within 10% Tan , IR : initial spec. Thermal Shock Appearance : No abnormal exterior appearance -55/+125. Capacitance Change : Within 10% Note: Number of cycles required-300, Tan , IR : initial spec. Maximum transfer time-20 sec, Dwell time-15min. Air-Air Appearance : No abnormal exterior appearance AEC-Q200-002 ESD Capacitance Change : Within 10% Tan , IR : initial spec. Solderability 95% of the terminations is to be soldered evenly and continuously a) Preheat at 155 for 4 hours, Immerse in solder for 5s at 2455 b) Steam aging for 8 hours, Immerse in solder for 5s at 2455 c) Steam aging for 8 hours, Immerse in solder for 120s at 2605 solder : a solution ethanol and rosin Electrical Capacitance : Within specified tolerance The Capacitance /D.F. should be measured at 25, Characterization Tan (DF) : 0.05max. 110%, 1.00.2Vrms IR(25) : More than 10,000 or 500x I.R. should be measured with a DC voltage not exceeding IR(125) : More than1,000 or 10x Rated Voltage @25, @125 for 60~120 sec. Whichever is Smaller Dielectric Strength Board Flex Dielectric Strength : 250% of the rated voltage for 1~5 seconds Appearance : No abnormal exterior appearance Bending to the limit (2) for 5 seconds Capacitance Change : Within 10% Terminal Appearance : No abnormal exterior appearance 10N, for 601 sec. Strength(SMD) Capacitance Change : Within 10% Beam Load Destruction value should not be exceed Beam speed Chip Length < 2.5 0.50.05/sec a) Chip Thickness > 0.5 : 20N b) Chip Thickness 0.5 : 8N Temperature X7R characteristic (From -55 to 125, Capacitance change should be within 15%) C. Recommended Soldering method : Reflow ( Reflow Peak Temperature : 260+0/-5, 10sec. Max ) Product specifications included in the specifications are effective as of March 1, 2013. Please be advised that they are standard product specifications for reference only. We may change, modify or discontinue the product specifications without notice at any time. So, you need to approve the product specifications before placing an order. Should you have any question regarding the product specifications specifications, please contact our sales personnel or application engineers.