Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series SMDJ Series Description Uni-directional Bi-directional The SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25C unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10x1000s Waveform (Fig.2)(Note 1), (Note 2) PPPM 3000 W Power Dissipation on Infinite Heat Sink at TA=50C PM(AV) 6.5 W IFSM 300 A VF 3.5 V TJ , TSTG -65 to 150 C Typical Thermal Resistance Junction to Lead RuJL 15 C/W Typical Thermal Resistance Junction to Ambient RuJA 75 C/W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25C per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Bi-directional Cathode Anode Uni-directional (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 * For surface mounted applications in order to optimize board space * Low profile package * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) * EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Built-in strain relief * Typical maximum temperature coefficient VBR = 0.1% x VBR@25C x T * Glass passivated chip junction * 3000W peak pulse power capability at 10x1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 2A above 12V * High temperature soldering guaranteed: 260C/40 seconds at terminals * Plastic package has underwriters laboratory flammability 94V-O * Matte tin lead-free plated * Halogen free and RoHS compliant Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. SMDJ Series RoHS Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Electrical Characteristics (TA = 25C unless otherwise noted) Part Number (Uni) Part Number (Bi) SMDJ5.0A SMDJ6.0A SMDJ6.5A SMDJ7.0A SMDJ7.5A SMDJ8.0A SMDJ8.5A SMDJ9.0A SMDJ10A SMDJ11A SMDJ12A SMDJ13A SMDJ14A SMDJ15A SMDJ16A SMDJ17A SMDJ18A SMDJ20A SMDJ22A SMDJ24A SMDJ26A SMDJ28A SMDJ30A SMDJ33A SMDJ36A SMDJ40A SMDJ43A SMDJ45A SMDJ48A SMDJ51A SMDJ54A SMDJ58A SMDJ60A SMDJ64A SMDJ70A SMDJ75A SMDJ78A SMDJ85A SMDJ90A SMDJ100A SMDJ110A SMDJ120A SMDJ130A SMDJ150A SMDJ160A SMDJ170A SMDJ180A SMDJ220A SMDJ5.0CA SMDJ6.0CA SMDJ6.5CA SMDJ7.0CA SMDJ7.5CA SMDJ8.0CA SMDJ8.5CA SMDJ9.0CA SMDJ10CA SMDJ11CA SMDJ12CA SMDJ13CA SMDJ14CA SMDJ15CA SMDJ16CA SMDJ17CA SMDJ18CA SMDJ20CA SMDJ22CA SMDJ24CA SMDJ26CA SMDJ28CA SMDJ30CA SMDJ33CA SMDJ36CA SMDJ40CA SMDJ43CA SMDJ45CA SMDJ48CA SMDJ51CA SMDJ54CA SMDJ58CA SMDJ60CA SMDJ64CA SMDJ70CA SMDJ75CA SMDJ78CA SMDJ85CA SMDJ90CA SMDJ100CA SMDJ110CA SMDJ120CA SMDJ130CA SMDJ150CA SMDJ160CA SMDJ170CA SMDJ180CA SMDJ220CA UNI BI Reverse Stand off Voltage VR (Volts) RDE RDG RDK PDM PDP PDR PDT PDV PDX PDZ PEE PEG PEK PEM PEP PER PET PEV PEX PEZ PFE PFG PFK PFM PFP PFR PFT PFV PFX PFZ RGE PGG PGK PGM PGP PGR PGT PGV PGX PGZ PHE PHG PHK PHM PHP PHR PHT PKE DDE DDG DDK DDM DDP DDR DDT DDV DDX DDZ DEE DEG DEK DEM DEP DER DET DEV DEX DEZ DFE DFG DFK DFM DFP DFR DFT DFV DFX DFZ DGE DGG DGK DGM DGP DGR DGT DGV DGX DGZ DHE DHG DHK DHM DHP DHR DHT DKE 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 220.0 Marking Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 198.00 242.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 230.40 281.60 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Maximum Maximum Agency Clamping Peak Reverse Approval Voltage VC Pulse Leakage IR @ Ipp Current Ipp @ VR (V) (A) (A) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 292.0 356.0 326.1 291.3 267.9 250.0 232.6 220.6 208.3 194.8 176.5 164.8 150.8 139.5 129.3 123.0 115.4 108.7 102.7 92.6 84.5 77.1 71.3 66.1 62.0 56.3 51.6 46.5 43.2 41.3 38.8 36.4 34.4 32.1 31.0 29.1 26.5 24.8 23.8 21.9 20.5 18.5 16.9 15.5 14.4 12.3 11.6 10.9 10.3 8.4 800 800 500 200 100 50 20 10 5 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For parts without A , the VBR is 10%, and VC is 5% higher than A parts. For bidirectional type having VR of 10 volts and less, the IR limit is double. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series SMDJ Series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT IT IR Vc VBR VR V IR IT VR VBR Vc V Ipp Ipp PPPM Peak Pulse Power Dissipation -- Max power dissipation VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation VBR Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT) VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) IR Reverse Leakage Current -- Current measured at VR VF Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (TA=25C unless otherwise noted) Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 1000 PPPM-Peak Pulse Power (KW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 100 10 1 0.31x0.31" (8.0x8.0mm) 0.1 Copper Pad Area 0.001 0.01 0.1 1 td-Pulse Width (ms) 10 Time continues on next page. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Ratings and Characteristic Curves (TA=25C unless otherwise noted) (Continued) Figure 3 - Peak Pulse Power or Current Derating Curve vs. Initial Junction Temperature Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 Peak Pluse Power (Single Pluse) 80 60 50 40 Average Power 20 0 0 25 50 75 100 125 150 tr=10sec Half Value IPPM IPPM ( ) 2 50 0 Tj - initial temperature (C) Cj (pF) Uni-directional V= OV Uni-directional @ VR 100 Bi-directional @ VR 10 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) PM(AV), Steady Sate Power Dissipation (W) Bi-directional V= OV 1 1.0 td 1.0 0 2.0 3.0 4.0 Figure 6 - Steady State Power Derating Curve 100000 1000 10/1000sec. Waveform as defined by R.E.A t-Time (ms) Figure 5 - Typical Junction Capacitance 10000 Peak Value IPPM 100 175 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 150 175 TA - Ambient Temperature(C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional only IFSM - Peak Forward Surge Current (A) 350 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Ramp-up TL Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260 Time within 5C of actual peak Temperature (tp) 20 - 40 seconds +0/-5 tp TP Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) C Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C Physical Specifications Critical Zone TL to TP Environmental Specifications Weight 0.007 ounce, 0.21 grams Temperature Cycle JESD22-A104 Case JEDEC DO214AB. Molded plastic body over glass passivated junction Pressure Cooker JESD 22-A102 Polarity Color band denotes positive end (cathode) except Bidirectional. High Temp. Storage JESD22-A103 HTRB JESD22-A108 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D Thermal Shock JESD22-A106 Dimensions DO-214AB (SMC J-Bend) Dimensions Cathode Band C A B H D F E G Dimensions in inches and (millimeters) J K L I Solder Pads (all dimensions in mm) (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 A Inches Millimeters Min Max Min Max 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - 2.400 J 0.094 - K - 0.165 L 0.094 - 4.200 2.400 - SMDJ Series Surface Mount - 3000W > SMDJ series Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Part Numbering System Part Marking System SMDJ XXX C A F Cathode Band 5% VBR VOLTAGE TOLERANCE BI-DIRECTIONAL XXX VR VOLTAGE YMXXX SERIES Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options Part number Component Package SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm/13" tape EIA STD RS-481 SMDJxxxXX-T7 DO-214AB 500 Tape & Reel - 16mm/7" tape EIA STD RS-481 Packaging Option Quantity Packaging Specification Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7" 7.0 (187) 13" 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13