56747 - LOCTITE - Datasheet.Live

Technical Data Sheet

LOCTITE® 567™

April-2015

PRODUCT DESCRIPTION

LOCTITE® 567™ provides the following product

characteristics:

Technology Acrylic

Chemical Type Methacrylate ester

Appearance (uncured) Smooth, creamy, off-white pasteLMS

Components One component -

requires no mixing

Viscosity High

Cure Anaerobic

Secondary Cure Activator

Application Thread sealing

Strength Low

LOCTITE® 567™ is designed for the locking and sealing of

metal tapered threads and fittings. The product cures when

confined in the absence of air between close fitting metal

surfaces and prevents loosening and leakage from shock and

vibration. The high lubricating properties of this compound

prevent galling on stainless steel, aluminum and all other metal

pipe threads and fittings. LOCTITE® 567™ is recommended for

industrial applications in the chemical processing, petroleum

refining, pulp/paper, waste treatment, textile, utilities/power

generation, marine, automotive, industrial equipment, gas

compression and distribution industries. It is also

recommended for industrial plant fluid power systems.

UL Classification

Classified by Underwriters Laboratories Inc.® MH8007 -

Fire hazard is small. No flash point in liquid state. Ignition

temperature 455°C. For use in devices handling gasoline,

petroleum oils, natural gas (pressure not over 300

PSIG), butane and propane not exceeding 2 in. pipe size.

Note: This is a regional approval. Please contact your local

Technical Service Center for more information and clarification.

ULC Classification

Classified by Underwriters Laboratories of Canada Inc.

MH27131 - An anaerobic material which contains a lubricant

and sets to form a tight seal and maintain a controlled locking

strength. For use in joining threaded pipe connections or other

closely fitting metal parts in devices handling natural gas and

methane, gasoline and petroleum oils, and propane and

butane at pressures not exceeding 13,790 kPa. Ignition

temperature greater than 460 °C. Classed less than 10 below

paraffin oil with respect to fire hazard. Note: This is a regional

approval. Please contact your local Technical Service Center

for more information and clarification.

Approved by the Australian Gas Association Certificate

number 3207 Class III rated working pressure 2000 KPa,

working temperature -10 to 205°C. Note: This is a regional

approval. Please contact your local Technical Service Center

for more information and clarification.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Specific Gravity @ 25 °C 1.1

Flash Point - See SDS

Viscosity, Brookfield - RVF, 25 °C, mPa·s (cP):

Spindle 7,, speed 2 rpm, 280,000 to 800,000LMS

TYPICAL CURING PERFORMANCE

Cure Speed vs. Substrate

The rate of cure will depend on the substrate used. The graph

below shows the breakaway strength developed with time on

3/8 NPT steel pipe tees and plugs compared to different

materials and tested according to ASTM D6396.

% of Full Strength on Steel

Cure Time

100

1min 5min10min 30min 1h 3h 6h 24h 72h

Steel

Brass

Zinc dichromate

Cure Speed vs. Temperature

The rate of cure will depend on the temperature. The graph

below shows the breakaway strength developed with time at

different temperatures on 3/8 NPT steel pipe tees and plugs

and tested according to ASTM D6396.

TDS LOCTITE® 567™, April-2015

% of Full Strength on Steel

Cure Time

100

1min 5min10min 30min 1h 3h 6h 24h 72h

40 °C

22 °C

Cure Speed vs. Activator

Where cure speed is unacceptably long, or large gaps are

present, applying activator to the surface will improve cure

speed. The graph below shows the breakaway strength

developed with time on 3/8 NPT steel pipe tees and plugs

using Activator 7471™ and 7649™ and tested according to

ASTM D6396.

% of Full Strength on Steel

Cure Time

100

1min 5min10min 30min 1h 3h 6h 24h 72h

Activator 7649™

Activator 7471™

No activator

TYPICAL PROPERTIES OF CURED MATERIAL

Physical Properties:

Coefficient of Thermal Expansion,

ISO 11359-2, K-1

80×10-6

Coefficient of Thermal Conductivity, ISO 8302,

W/(m·K)

0.1

Specific Heat, kJ/(kg·K) 0.3

TYPICAL PERFORMANCE OF CURED MATERIAL

Adhesive Properties

After 24 hours @ 22 °C

Breakaway Torque, ISO 10964:

3/8 x 24 steel nuts (grade

2) and bolts (grade 2)

N·m ≥1.7LMS

(lb.in.) (≥15)

After 4 hours @ 22 °C

Breakaway Torque, ISO 10964:

3/8 x 24 steel nuts (grade

2) and bolts (grade 2)

N·m ≥0.3LMS

(lb.in.) (≥2.6)

TYPICAL ENVIRONMENTAL RESISTANCE

Cured for 72 hours @ 22 °C

Breakloose Torque, ISO 10964, Pre-torqued to 1.1 N·m:

M10 steel fasteners (degreased)

Heat Aging

Aged at temperature indicated and tested @ 22 °C

% Initial Strength @ 22 °C

Exposure Time, hours

250

200

150

100

0 1000 2000 3000 4000 5000

120 °C

150 °C

200 °C

Chemical/Solvent Resistance

Aged under conditions indicated and tested @ 22 °C.

% of initial strength

Environment °C 100 h 500 h 1000 h

Motor oil (MIL-L-46152) 40 100 100 100

Gasoline 22 90 80 80

Brake fluid 22 90 90 80

Ethanol 22 85 85 85

Acetone 22 75 70 60

1,1,1 Trichloroethane 22 90 90 85

Water/glycol 50/50 87 100 75 75

E85 Ethanol fuel 22 N/A 85 130

B100 Bio-Diesel 22 N/A 105 90

DEF (AdBlue®)22 N/A 130 120

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected as

a sealant for chlorine or other strong oxidizing materials.

For safe handling information on this product, consult the

Safety Data Sheet (SDS).

Where aqueous washing systems are used to clean the

surfaces before bonding, it is important to check for

compatibility of the washing solution with the adhesive. In

some cases these aqueous washes can affect the cure and

performance of the adhesive.

This product is not normally recommended for use on plastics

(particularly thermoplastic materials where stress cracking of

the plastic could result). Users are recommended to confirm

compatibility of the product with such substrates.

Directions for use:

For Assembly

1. For best results, clean all surfaces (external and internal)

with a LOCTITE® cleaning solvent and allow to dry.

2. If the material is an inactive metal or the cure speed is

too slow, spray with Activator 7471™ or

7649™ and allow to dry.

3. Apply a 360° bead of product to the leading threads of

Henkel Americas

+860.571.5100

Henkel Europe

+49.89.320800.1800

Henkel Asia Pacific

+86.21.2891.8859

For the most direct access to local sales and technical support visit: www.henkel.com/industrial

TDS LOCTITE® 567™, April-2015

the male fitting, leaving the first thread free. Force the

material into the threads to thoroughly fill the voids. For

bigger threads and voids, adjust product amount

accordingly and apply a 360° bead of product on the

female threads also.

4. Using compliant practices, assemble and wrench tighten

fittings in accordance with manufacturers

recommendations.

5. Properly tightened fittings will seal instantly to moderate

pressures. For maximum pressure resistance and

solvent resistance allow the product to cure a minimum of

24 hours.

For Disassembly

1. Remove with standard hand tools.

2. Where hand tools do not work because of excessive

engagement length or large diameters (over 1"), apply

localized heat to approximately 250 °C. Disassemble

while hot.

For Cleanup

1. Cured product can be removed with a combination of

soaking in a Loctite solvent and mechanical abrasion

such as a wire brush.

Loctite Material SpecificationLMS

LMS dated September-1, 1995. Test reports for each batch

are available for the indicated properties. LMS test reports

include selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

Storage

Store product in the unopened container in a dry location.

Storage information may be indicated on the product container

labeling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

Corporation cannot assume responsibility for product which

has been contaminated or stored under conditions other than

those previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representative.

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

µm / 25.4 = mil

N x 0.225 = lb

N/mm x 5.71 = lb/in

N/mm² x 145 = psi

MPa x 145 = psi

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Note:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The product

can have a variety of different applications as well as differing application and

working conditions in your environment that are beyond our control. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and

Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is

applicable:

The data contained herein are furnished for information only and are believed to

be reliable. We cannot assume responsibility for the results obtained by others

over whose methods we have no control. It is the user's responsibility to

determine suitability for the user's purpose of any production methods mentioned

herein and to adopt such precautions as may be advisable for the protection of

property and of persons against any hazards that may be involved in the handling

and use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties of

merchantability or fitness for a particular purpose, arising from sale or use

of Henkel Corporation’s products. Henkel Corporation specifically

disclaims any liability for consequential or incidental damages of any kind,

including lost profits. The discussion herein of various processes or

compositions is not to be interpreted as representation that they are free from

domination of patents owned by others or as a license under any Henkel

Corporation patents that may cover such processes or compositions. We

recommend that each prospective user test his proposed application before

repetitive use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

Trademark usage

Except as otherwise noted, all trademarks in this document are trademarks of

Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark

registered in the U.S. Patent and Trademark Office.

Reference 1.5

Henkel Americas

+860.571.5100

Henkel Europe

+49.89.320800.1800

Henkel Asia Pacific

+86.21.2891.8859

For the most direct access to local sales and technical support visit: www.henkel.com/industrial