Technical Document LCD Specification LCD Group LQ043T3DW03LCD LCD Module Product Specification February 2011 Normally Black module with very high contrast and brightness ratings, very wide symmetric viewing angles, and a 50,000-hr rated backlight, very high contrast of 800:1, brightness of 360 nits. RECORDS OF REVISION LQ043T3DW03 REVI SED No PAGE SPEC No. DATE LD-22604A 2010/6/21 A LD-22604B 2010/8/27 B SUMMARY - P7 7-1 Pixel Clock Timing chart "VIL" : from "0.1VCC" to 0.2VCC "VIH" : from "0.9VCC" to 0.8VCC. LD-22604C 2011/2/8 C P17 Fig.1 Outline Dimension Add Dimension, Tolerance and Detail of FPC Terminal. NOTE - Contents No. page NOTICE 1 1 Application 2 2 Overview 2 3 Mechanical Specifications 4 Input Terminals 5 Absolute Maximum Ratings 4 6 Electrical Characteristics 5 7 Timing characteristics of input signals 8 Input Signals, Basic Display Colors and Gray Scale of Each Color 10 9 Optical Characteristics 11 10 Handling Precautions 13 11 Packing form 14 12 Reliability test items 14 13 Others 15 14 Storage conditions 16 Fig.1 Outline Dimensions 17 Fig.3 Packing 18 2 3 7 LD-22604C- 1 <NOTICE> This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs, such as: Personal computers Office automation Test and measurement equipment Industrial control Audio visual and multimedia equipment Telecommunication equipment Consumer electronics The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: Transportation control and safety equipment(i.e. aircraft, trains, automobiles, etc.) Traffic signals Alarm equipment Gas leakage sensor breakers Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: Military and space applications Nuclear power control equipment Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. LD-22604C- 2 1Application This spec sheet applies to the color TFT-LCD module LQ043T3DW03. 2Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver IC, control circuit(FPC), and a White-LED Backlight unit. Graphics and texts can be displayed on a 480xRGBx272dots panel with 16,777,216 colors by supplying 24bit data signal (8bitxRGB), four timing signals ,DC supply voltages for TFT-LCD panel driving and supply voltage for backlight. LED drive circuit for backlight is not built in this module. 3Mechanical Specifications Parameter technical literatures Unit Display size 114.3inchDiagonal cm Active area 95.04H)x53.86V) mm Pixel format 480H)x272V) (1pixelRGB dot) Pixel pitch 0.198H)x0.198V) Pixel configuration R,G,B horizontal stripe Display mode Unit outline dimensions *1 Unit outline dimensions *2 Mass Normally black Surface treatment 105.5W)x67.2H)x7.7(D) 105.5W)x67.2H)x6.1(D) 85 Max. Anti-glare and hard-coating 3H *1 excluding FPC. Outline dimensions are shown in Fig.1. *2 excluding FPC and Spacer. pixel mm mm g LD-22604C- 3 4Input Terminals 4-1TFT-LCD panel driving CN1 Corresponding connectors 04 6288 040 000 846+ (KYOCERA ELCO Co., Ltd.) 04 6275 040 000 829+ (KYOCERA ELCO Co., Ltd.) NOTE Please do not use it besides corresponding connector. Pin Symbol Function Polarity Remark Ground GND 1 Ground GND 2 Not Connected NC 3 power supply (Digital) VCC 4 RED data signal (LSB) R0 5 RED data signal R1 6 RED data signal R2 7 RED data signal R3 8 RED data signal R4 9 R5 RED data signal 10 R6 RED data signal 11 RED data signal (MSB) R7 12 GREEN data signal (LSB) G0 13 GREEN data signal G1 14 GREEN data signal G2 15 GREEN data signal G3 16 GREEN data signal G4 17 G5 GREEN data signal 18 GREEN data signal G6 19 GREEN data signal (MSB) G7 20 B0 BLUE data signal (LSB) 21 B1 BLUE data signal 22 B2 BLUE data signal 23 B3 BLUE data signal 24 B4 BLUE data signal 25 B5 BLUE data signal 26 B6 BLUE data signal 27 B7 BLUE data signal (MSB) 28 GND Ground 29 PCLK Clock signal for sampling each data signal 30 *1 DISP Sleep mode control 31 Hsync Horizontal synchronous signal Negative 32 Vsync Vertical synchronous signal Negative 33 *2 DE Signal to settle the horizontal display position Positive 34 VDD power supply (Analog) 35 NC Not Connected 36 GND Ground 37 C1 Power supply for LED (Cathode 1) 38 C2 Power supply for LED (Cathode 2) 39 A Power supply for LED (Anode) 40 *1 Please refer to 7-3. *2 The horizontal display start timing is settled in accordance with a rising timing of DE signal. In case DE is fixed "Low", the horizontal start timing is determined as described in 7-2. Do not keep DE "High" during operation. LD-22604C- 4 5Absolute Maximum Ratings Parameter Symbol Condition Pin Ratings Unit Remark Digital Supply voltage Vcc Ta=25 VCC -0.3 4.0 V *1 Analog Supply voltage VDD Ta=25 VDD -0.3 5.0 V *1 Input voltage VI Ta=25 *2 -0.3+VCC+0.3 V VDD-VCC relation - Ta=25 - VDD-VCC0 V Storage temperature TSTG - -25 70 *1 Operating temperature TOPA - -10 70 *1,3,4 *1 Humidity95%RH Max.( Ta40 ) Note static electricity. Maximum wet-bulb temperature at 39 or less. (Ta>40) No condensation. *2 R0R7, G0G7, B0B7, Hsync , Vsync , DE , DISP , PCLK *3 There is a possibility of causing deterioration in the irregularity and others of the screen and the display fineness though the liquid crystal module doesn't arrive at destruction when using it at 6070. *4 In the operating temperature item, the low temperature side is the ambient temperature regulations. The high temperature side is the panel surface temperature regulations. LD-22604C- 5 6Electrical Characteristics Ta+25 6-1TFT-LCD panel driving Parameter Digital Power Supply Analog Power Supply Condition Min. Typ. Max. Unit Remark 3.3 0.9 3.5 1.5 V V=3.3V 3.0 - mA *1 *2 3.0 3.3 3.5 V *1 - 13 18 mA *2 VRFVCC 100 mVp-p Vcc=3.3V VRFVDD 100 mVp-p VDD=3.3V VIL 0 0.2VCC V *3 VIH 0.8VCC VCC V IOL -1.0 -1.0 1.0 1.0 A Symbol VCC Supply voltage Current dissipation ICC VDD Supply voltage Current dissipation IDD Permissive input ripple voltage Logic input voltage Logic input reak current VDD=3.3V IOH A VI =0V*3 VI =+3.3V *3 *1 On-off conditions for supply voltage 0.1 VCC VCC t1 t2 200ms t4 t7 0ms t5 5ms 0.5VCC t6 t5 1us t6 5ms 100ms t7 0.9 VCC 0.9 VCC VDD 2ms t3 10ms t4 0.5VCC 0 0.1 VCC 0.1 VCC t8 t8 25ms 1ms t9 10ms t11 1ms t10 10ms signal t9 t1 25ms 2ms t2 10ms 0.1 VCC t3 signal DISP 0 0.9 VCC 0.9VCC t10 200ms t11 Vcc-dip conditions VCC Vmin Vth Vth = 1.5V Vmin = 3.0V td Vth VCC Vmin td 10ms VDD-dip conditions VCC VDD Vmin Vth Vth = 2.5V Vmin = 3.0V td *2 Typical Current Situation All White Pattern Vth Vcc-dip conditions should also follow the On-off conditions for supply voltage Vcc=+3.3VVDD=+3.3Vfck = 8.54MHzTa=25 *3 R0R7, G0G7, B0B7, Hsync , Vsync , DE , DISP , PCLK LD-22604C- 6 6-2Backlight Driving The backlight system is edge-lighting type with white-LED. The characteristics of LED are shown in the following table. Ta+25 Parameter Symbol Min. Typ. Max. Unit Remark LED Voltage VL - 24.5 27.2 V *1 LED Current Range IL - 45 60 mA *2 Number of Circuit channe - - 1.0 - LED Power Consumption PL - 1.2 - W Life time LL - - h 50000 (Module) *1 The LED backlight is composed of 1 channel which 8 LED is connected in series. *2 Calculated value for reference (I L x VL x 1 channel) *3 Lighting condition: The state of the LCD module installation: Landscape position and standing position Atmosphere temperature: 50 Lighting current: 45mA (Constant current driveContinuous turning on) Definition of Life time: Luminance becomes 50% of an initial value. (under condition ) Reference *3 LD-22604C- 7 7Timing characteristics of input signals 7-1 Pixel Clock Timing VSYNC tvsys t vsyh 0.2VCC 0.2VCC t hsys HSYNC 0.2VCC 0.8VCC PCLK 0.8VCC 0.2VCC 0.2VCC t CKL tr t ds 0.8VCC 0.2VCC DATA 0.2VCC tPCLK t hv R0R7 G0G7 B0B7 t hsyh 0.8VCC 0.2VCC 0.8VCC 0.8VCC 0.2VCC tCKH t dh 0.8VCC 0.2VCC DATA DATA tr / tf Parameter Symbol Min. Typ. Max. Unit PCLK Frequency fPCLK 8.0 - 9.0 MHz PCLK Period tPCLK 115 - - nSec Pixel Clock Period tPIXCLK - 1.0 - tPCLK Pixel Clock Frequency fPIXCLK - - 9.0 MHz Vertical Sync Setup Time tvsys 5 - - nSec Vertical Sync Hold Time tvsyh 5 - - nSec Horizontal Sync Setup Time thsys 5 - - nSec Horizontal Sync Hold Time thsyh 5 - - nSec Phase difference of Sync Signal Falling Edge thv 0 - 480 tPCLK PCLK Low Period tCKL 18 - - nSec PCLK High Period tCKH 18 - - nSec Data Setup Time tds 10.0 - - nSec Data Hold Time tdh 15 - - nSec Rise / Fall Time tr / tf 5 - 25 nSec Remark LD-22604C- 8 7-224-bit RGB Interface Timing Diagram & Transaction Example VSYNC DE R0-R7 G0B0-B7 PCLK DE R0-R7 G0B0-B7 HV SYNC Mode Characteristics Symbol min typ max Units Serial Clock Frequency 1/t PCLK 8.0 8.54 9.0 MHz One Line Period tH 500 512 - tPCLK Active Data Period Horizontal Back Porch Horizontal Front Porch One Field Period tdata 480 480 480 tPCLK Fix tHBP 16 16 16 tPCLK Fix tvsys 4 16 - tPCLK tV 278 278 278 tH tAL 272 272 272 tH tVBP 4 4 4 tH tVFP 2 2 2 tH Horizontal Vertical Active Line Period Vertical Back Porch Vertical Front Porch Remark Fix In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur. LD-22604C- 9 7-3Input Data Signals and Display Position on the screen R G 1, 1 D(1,1) D(2,1) D(3,1) B D(1,2) D(2,2) R D(1,3) G B ,1) R G B 1, 2 D(1, D( 480 272 ) D( 480 , 272 ) LD-22604C- 10 8Input Signals, Basic Display Colors and Gray Scale of Each Color Data signal Gray Scale of Blue Gray Scale of Green Gray Scale of Red Basic Color Colors & Gray scale Gray Scale R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Brighter GS253 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS254 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red GS255 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Brighter GS253 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 GS254 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Green GS255 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Brighter GS253 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 GS254 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 Blue GS255 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 :Low level voltage 1 :High level voltage :Don't care Each basic color can be displayed in256 gray scales from 8 bit data signals. According to the combination of total 24 bit data signals, the 16,777,216-color display can be achieved on the screen. LD-22604C- 11 9Optical Characteristics Ta=+25, Vcc=3.3V Parameter Viewing angle range Symbol Horizontal 3,9 Vertical 6,12 Contrast ratio CR Condition CR>10 optimized angle Min. Typ. Max. Unit 70 80 - Deg. 70 80 - Deg. 400 800 - Remark *1,2,4 *2,4 Risw r - 30 - ms *3,4 Decay d - 30 - ms *3,4 0.270 0.320 0.370 0.308 0.358 0.408 280 400 - Response Time Wx Chromaticity of White Wy Luminance of white YL1 =0 *4 cd/m2 *4 The measurement shall be executed 30 minutes after lighting at rating.(conditionIL45mA) The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig.2 below. Photodetector Response timeBM-5A Contrast/Luminance/ChromaticitySR-3 Photodetector(EZ-CONTRAST 400mm Field=1 Panel center(=0 Panel center(=0) TFT-LCD module TFT-LCD module fig.2-1 Measuring method of Viewing angle range. fig.2-2 Measuring method of contrast, luminance, response time, and Chromaticity. Fig.2 Optical characteristics measurement method *1Definitions of viewing angle range: 9 LD-22604C- 12 Normal line 12 3 6 6 O'clock *2Definition of contrast ratio: The contrast ratio is defined as the following. Contrast CR Luminance with all pixels white Luminance with all pixels black *3Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". Photodetector Output (Relative Value) White White Black 100% 90% 10% 0% d r Time *4This shall be measured at center of the screen. LD-22604C- 13 10 Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the FPC. b) Please insert FPC in the connector carefully so that the tension should not hang. Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. d) Since the front polarizer is easily damaged, pay attention not to scratch it. Blow away dust on the polarizer with antistatic 2 blow. It is undesirable to wipe off because a polarizer is sensitive. c) It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer. When unavoidable, wipe off carefully with a cloth for wiping lenses. e) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. f) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. g) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. h) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling.Observe all other precautionary requirements in handling components. i) Since there is a circuit FPC in the module back, stress is not added at the time of a design assembly. Please make it like. If stress is added, there is a possibility that circuit parts may be damaged. j) LCD-FPC has electronic devices on its own. Please make sure electric insulation between that portion (the devices and soldering ) and the user's set. k) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which degrades display quality. l) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such environment. The panel characteristic might be deteriorated and the display fineness decrease when strong light is irradiated to the liquid crystal panel. m) When handling LCD modules and assembling them into cabinets, that long-terms storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, causes corrosion and discoloration of the modules. Therefore, please avoid these use. Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and oxime series), tray forming agent (azo compound) etc, in the cabinet or the packing materials may induce abnormal display with polarizer film deterioration regardress of contact or noncontact to polarizer film. Be sure to confirm the component of them. n) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake. o) Notice:Never dismantle the module , because it will cause failure. Moreover, please do not peel off the tapes other than the creped paper tape (yellow tape) of a protection film pasted to the product. p) Be careful when using it for long time with fixed pattern display as it may cause afterimage. (Please use a screen saver etc., in order to avoid an afterimage.) q) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue,etc Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan. r) The LED used for this product is very sensitive to the temperature. Luminance decreases rapidly when it issued for a long time under the environment of the high temperature. Please consult our company when it is used under the environment like the above mentioned. s) Please make the LED lighting power supply an independent fixed current drive composition in each channel. When each channel of LED is driven parallel, the display fineness and longevity might be deteriorated. for a long time under the environment of the high temperature. Please consult our company when it is used under the environment like the above mentioned. ) Don't give any stress to the joint part of FPC and LCD panel , please avoid the bend to panel side. LD-22604C- 14 11Packing form a) Piling number of cartons MAX8 b) Package quantity in one carton 80pcs c) Carton size(TYP) 580mm(W) x 365mm(D)x235mm(H) d) Total mass of one carton filled with full modules(80pcs) 9kg e) Packing form fig fig3 12Reliability test items 6 Test item High temperature storage test Low temperature strage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Vibration test 7 Shock test No. 1 2 3 4 5 Conditions Ambient temperature 70 240H Remark Note1 Ambient temperature -25 240H Note1 Ambient temperature 40Humidity 95 RH 240H No condensation. Note1 Panel surface 70 240H Note1 Ambient temperature -10 240H Note1 Sin wave Frequency 1057HzVibration width (one side) 0.076mm 57500HzGravity9.8m/s2 Sweep time11minutes Test period 3HXYZ direction 1H Max. gravity490m/s2 Pulse width11ms DirectionX,Y,Z Test period 1time1direction Note1 Note1 Note1 Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. (normal operation stateTemperature:1535, Humidity:4575, Atmospheric pressure:86106kpa) LD-22604C- 15 13Others 13-Lot No Label: Module serial label The label that displays Model No. LQ043T3DW03Lot No. is stuck on the back of the module. Lot No display methodFigure and alphabet LQ043T3DW03 Model No. Serial No. Space Production year (Last digit of dominical year) Assembly site code Discernment code Production month (1-9X, Y, Z) B Packing box Label: The label that displays Model number LQ043T3DW03 Lot number Quantity of module is stuck on the packing box. Moreover, the display of bar code also applies to this. (4S) LQ043T3DW03 Barcode Lot No. 1T 2010. 10. 01 Barcode Quantity Q Model number LQ043T3DW03 Lot number (DATA) Quantity of module 80 pcs Barcode Our management product number might be filled Example LQ043T3DW03A etc. A right picture is written to the packing box of module for the RoHS restriction. R.C.RoHs Compliancemeans these parts have corresponded with the RoHs directive. This module corresponds from the first sample to RoHS Directive. 13-3 The ozone-depleting substances is not used. 13-4 If any problem occurs in relation to the description of this spec sheet, it shall be resolved through discussion with spirit of cooperation. R.C. LD-22604C- 16 14Storage conditions Environmental condition range of storage temperature and humidity Temperature 0 to 40 degrees Celsius Relative humidity 95% and below Note Please refer below as a mean value of the environmental conditions. Summer time temperature 20 to 35 degrees Celsius humidity , 85% and below Winter time temperature 5 to 15 degrees Celsius humidity , 85% and below Please maintain within 240 hours of accumulated length of storage time, with conditions of 40 degrees Celsius and room humidity of 95%. Direct sunshine Please keep it in the state of wrapping or the darkroom so that direct sunshine should not strike directly into the product. Atmosphere Please do not keep it in the place with the danger of the generation of the causticity gas and the volatile solvent. Asking for be dewy prevention Please do not put directly on the floor, and keep the wrapping box on the palette or the stand to avoid the be dewy. Moreover, please arrange it in a constant direction correctly to improve ventilation under the palette. Please separate from the wall in the storage warehouse and keep it. Please note that ventilation is improved and consider the installation such as ventilators in the warehouse. Please manage so that there is no rapid temperature change more than natural environment. Keeping period Please make it to keeping within one year under the above-mentioned keeping condition. LD-22604C- 16 14Storage conditions Environmental condition range of storage temperature and humidity Temperature 0 to 40 degrees Celsius Relative humidity 95% and below Note Please refer below as a mean value of the environmental conditions. Summer time temperature 20 to 35 degrees Celsius humidity , 85% and below Winter time temperature 5 to 15 degrees Celsius humidity , 85% and below Please maintain within 240 hours of accumulated length of storage time, with conditions of 40 degrees Celsius and room humidity of 95%. Direct sunshine Please keep it in the state of wrapping or the darkroom so that direct sunshine should not strike directly into the product. Atmosphere Please do not keep it in the place with the danger of the generation of the causticity gas and the volatile solvent. Asking for be dewy prevention Please do not put directly on the floor, and keep the wrapping box on the palette or the stand to avoid the be dewy. Moreover, please arrange it in a constant direction correctly to improve ventilation under the palette. Please separate from the wall in the storage warehouse and keep it. Please note that ventilation is improved and consider the installation such as ventilators in the warehouse. Please manage so that there is no rapid temperature change more than natural environment. Keeping period Please make it to keeping within one year under the above-mentioned keeping condition. LC-22604C-17 Fig.1 LQ043T3DW03 OUTLINE DIMENSIONS LD-22604C- 18 Fig3 Packing form figure Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-8700 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328 CHINA Sharp Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: 49 (0)180 507 35 07 Fax: (49) 40-2376-2232 www.sharpsme.com JAPAN Sharp Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com SINGAPORE Sharp Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855 HONG KONG Sharp-Roxy (Hong Kong) Ltd. Level 26, Tower 1, Kowloon Commerce Centre, No. 51, Kwai Cheong Road, Kwai Chung, New Territories, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 602-603, 6/F., International Chamber of Commerce Tower, 168 Fuhua Rd. 3, CBD, Futian District, Shenzhen 518048, Guangdong, P.R. China Phone: (86) 755-88313505 Fax: (86) 755-88313515 KOREA Sharp Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage.