DC/DC Converters TEN 15 Series, 15 Watt Features Wide 2:1 input range High efficiency up to 88% Extended operating temperature range -40C to +85C no e or n f d e d en mm o c e r t sign e d w in Indefinite short circuit protection I/O isolation 1500 VDC Input filter to meet EN 55022, Class A and FCC, level A without external components Industry standard footprint Shielded metal case with insulated baseplate 3-year product warranty The TEN 15 series is a family of high performance 15W DC/DC converters in a compact 2" x 1" low profile package with industry standard footprint. A high efficiency allows a wide operating temperature range of -40C to +85C. A built-in EMI filter is built in to meet EN 55022, class A without any external components. Further standard features include over voltage protection and short-circuit protection. Typical applications for these converters are battery operated equipment, instrumentation, distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required. Models Order code TEN 15-1210 TEN 15-1211 TEN 15-1212 TEN 15-1213 TEN 15-1221 TEN 15-1222 TEN 15-1223 TEN 15-2410 TEN 15-2411 TEN 15-2412 TEN 15-2413 TEN 15-2421 TEN 15-2422 TEN 15-2423 TEN 15-4810 TEN 15-4811 TEN 15-4812 TEN 15-4813 TEN 15-4821 TEN 15-4822 TEN 15-4823 http://www.tracopower.com Input voltage range 9 - 18 VDC (12 VDC nominal) 18 - 36 VDC (24 VDC nominal) 36 - 75 VDC (48 VDC nomial) Output voltage 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC Output current max. 4'000 mA 3`000 mA 1'250 mA 1`000 mA 1500 mA 625 mA 500 mA 4'000 mA 3`000 mA 1`250 mA 1`000 mA 1'500 mA 625 mA 500 mA 4`000 mA 3`000 mA 1`250 mA 1`000 mA 1`500 mA 625 mA 500 mA Efficiency typ. 79 % 82 % 86 % 86 % 83 % 86 % 84 % 80 % 84 % 85 % 85 % 84 % 86 % 86 % 81 % 83 % 87 % 86 % 85 % 88 % 87 % Page 1 of 4 DC/DC Converters TEN 15 Series 15 Watt Input Specifications Input current at no load 12 Vin models: 30 mA typ. 24 Vin models: 20 mA typ. 48 Vin models: 15 mA typ. Input current at full load 12 Vin; 3.3 VDC 12 Vin; other 24 Vin; 3.3 VDC 24 Vin; other 48 Vin; 3.3 VDC 48 Vin; other Surge voltage (100 msec. max.) models: models: models: models: models: models: 1470 mA typ. 1550 mA typ. 730 mA typ. 780 mA typ. 360 mA typ. 380 mA typ. 12 Vin models: 36 V max. 24 Vin models: 50 V max. 48 Vin models: 100 V max. Conducted noise (input) EN 55022 level A, FCC part 15, level A Output Specifications Voltage set accuracy 1 % Regulation - Input variation Vin min. to Vin max. - Load variation 2 % - 100 % single output models: dual output models: 0.5 % max. 0.5 % max. 1 % max. (balanced load) 5 % max. (load cross variation 25 % / 100 %) Minimum load 2 % of rated max. output current. (Operation at lower load is safe but major deviations to specifyed data may occur) Ripple and noise (20 MHz Bandwidth) single output models: 50 mVpk-pk max. dual output models: 75 mVpk-pk max. Temperature coefficient 0.02 %/K Start up time (nominal Vin and constant resistive load) 20 ms typ. Transient response (25 % load step change) 250 s typ. Short circuit protection continiuous (automatic recovery) Over load protection 150 % of Iout max typ. foldback Over voltage protection 3.3 5.0 12 15 VDC VDC VDC VDC models: models: models: models: 3.9 V 6.2 V 15 V 18 V Capacitive load 3.3 5 12 15 5 12 15 VDC VDC VDC VDC VDC VDC VDC models: models: models: models: models: models: models: 10`200 F max. 7`050 F max. 1`035 F max. 750 F max. 1`020 F max. 495 F max. 165 F max. All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4 DC/DC Converters TEN 15 Series 15 Watt General Specifications Temperature ranges - Operating - 40C to +85C - Casing temperature +100C max. - Storage -55C to +105C Derating 3.3 / 5.0 VDC models: 2.5 %/K above 60C other models: 3.3 %/K above 70C Thermal impedance - Natural convection 12C/W - Natural convection with heatsink10C/W Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25C, ground benign) >2.3 Mio h Isolation Test Voltage (Input/Output, 60s) 1`600 VDC Insulation System Functional Isolation Capacitance (Input/Output) 300 pF max. Isolation Resistance (Input/Output) >1 G Ohm Switching frequency EMC immunity - - - - - single output models: 500 kHz typ. (pulse width modulation) dual output models: 300 kHz typ. (pulse width modulation) Electrostatic discharge ESD RF field susceptibility Electrical fast transient / burst immunity input Surge immunity Immunity to conducted RF disturbances EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 8 kV / 6 kV, criteria B 10 V/m, criteria A 2 kV, criteria B 1 kV, criteria B 10 Vrms, criteria A Vibration acc. MIL-STD-810F Thermal shock acc. MIL-STD-810F Safety standards UL 60950-1, EN 60950-1, IEC 60950-1 Safety approvals - UL/cUL www.ul.com -> certifications -> File e188913 Environmental compliance - Reach www.tracopower.com/info/reach-declaration.pdf - RoHS RoHS directive 2011/65/EU Physical Specifications Casing material copper, nickel plated Baseplate material non conductive FR4 Potting material epoxy (UL 94V-0 rated) Weight 27 g (09.5oz) Soldering temperature max. +265C / 10 sec. Supporting documents : www.tracopower.com/overview/ten15 All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated. http://www.tracopower.com Page 3 of 4 DC/DC Converters TEN 15 Series 15 Watt Outline Dimensions (2.0) 5 Dual 1 +Vin (Vcc) +Vin (Vcc) (1.0) 4 Single 2 -Vin (GND) -Vin (GND) 3 +Vout +Vout 4 No pin Common 5 -Vout -Vout 6.0 10.2 (0.24) (0.4) 1 2 2.5 (0.4) 10.2 (0.2) 5.08 3 Bottom View Pin 25.4 Pin-Out (0.4) (0.8) (0.4) 20.32 (0.6) (0.1) 15.2 10.16 10.16 50.8 Insulated baseplate Dimensions in [mm], () = Inch Pin diameter: 1.0 0.05 (0.02 0.002) Pin pitch tolerances: 0.25 (0.01) Casing tolerances: 0.5 (0.02) Heat-Sink (Option) Order code: TEN-HS1 (cont.: heat-sink, thermal pad, 2 clamps) Material: Aluminum Finish: Anodic treatment (black) Weight: 17g (0.60oz) without converter Thermal impedance after assembling: 10 K/W 56.0 (2.2) max. Note: The product label on converter has to be removed before mounting the heat-sink. Heat-sink Thermal pad Clamp Converter For volume orders converters will be supplied with heat-sinks already mounted. Please contact factory for quotation. Separate heat-sinks are only available for prototypes and small quantity orders. 14.5 (0.57) 16.8 (0.66) max. Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com www.tracopower.com Rev. July 11, 2018 Page 4 of 4