RClamp0504S RailClamp Low Capacitance TVS Array PROTECTION PRODUCTS - RailClamp Description Features Transient protection for high-speed data lines to RailClamps are surge rated diode arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (Cable Discharge Events), and EFT (electrical fast transients). The unique design incorporates surge rated, low capacitance steering diodes and a TVS diode in a single package. During transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. The internal TVS diode prevents over-voltage on the power line, protecting any downstream components. The low capacitance array configuration allows the user to protect four high-speed data or transmission lines. The low inductance construction minimizes voltage overshoot during high current surges. This device is optimized for ESD protection of portable electronics. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (15kV air, 8kV contact discharge). IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal TVS Diode Small package saves board space Protects up to four I/O lines & power line Low capacitance (<3pF) for high-speed interfaces No insertion loss to 2.0GHz Low leakage current and clamping voltage Low operating voltage: 5.0V Solid-state silicon-avalanche technology Mechanical Characteristics JEDEC SOT-23 6L package Nominal Dimensions: 2.9x2.8mm RoHS/WEEE Compliant Molding compound flammability rating: UL 94V-0 Marking: Marking Code Packaging: Tape and Reel Applications Circuit Diagram USB 2.0 USB OTG Monitors and Flat Panel Displays Digital Visual Interface (DVI) Gigabit Ethernet IEEE 1394 Firewire Ports Schematic & PIN Configuration 5 1 3 4 6 2 SOT-23 6L (Top View) Revision 01/17/2008 1 www.semtech.com RClamp0504S PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20s) Pp k 150 Watts Peak Pulse Current (tp = 8/20s) IP P 6 A ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) VESD 15 8 kV TJ -55 to +125 C TSTG -55 to +150 C Op erating Temp erature Storage Temp erature Electrical Characteristics (T=25oC) Parameter Symbol Conditions Minimum Typical Maximum Units Reverse Stand-Off Voltage VRWM Pi n 5 to 2 5 V Reverse Breakdown Voltage V BR It = 1mA Pi n 5 to 2 Reverse Leakage Current IR VRWM = 5V, T=25C Pi n 5 to 2 3 A Clamp ing Voltage VC IPP = 1A, tp = 8/20s A n y p i n to p i n 2 15 V Clamp ing Voltage VC IPP = 6A, tp = 8/20s A n y p i n to p i n 2 25 V Junction Cap acitance Cj VR = 0V, f = 1MHz Any I/O p in to p in 2 3 pF VR = 0V, f = 1MHz Between I/O p ins 1.5 pF 6 V Note 1: I/O pins are pin 1, 3, 4, and 6 2008 Semtech Corp. 2 www.semtech.com RClamp0504S PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 10 110 % of Rated Power or IPP Peak Pulse Power - P PP (kW) 100 1 0.1 90 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 0 1000 25 50 75 100 125 150 Ambient Temperature - TA (oC) Pulse Duration - tp (s) Pulse Waveform Clamping Voltage vs. Peak Pulse Current 110 Waveform Parameters: tr = 8s td = 20s 90 Percent of I PP 80 70 30 25 Clamping Voltage - VC (V) 100 e-t 60 50 40 td = IPP/2 30 20 10 Line to Line 20 15 Line to Ground 10 Waveform Parameters: tr = 8s td = 20s 5 0 0 5 10 15 20 25 0 30 0 Time (s) Forward Voltage vs. Peak Pulse Current 1 2 3 4 5 Peak Pulse Current - IPP (A) 6 7 Normalized Junction Capacitance vs. Reverse Voltage 8 1.4 1.2 6 CJ(VR) / CJ(VR=0) Forward Voltage - V F (V) 7 5 4 3 Waveform Parameters: tr = 8s td = 20s 2 1 1 0.8 0.6 0.4 0.2 f = 1 MHz 0 0 0 1 2 3 4 5 6 0 Peak Pulse Current - IPP (A) 2008 Semtech Corp. 3 1 2 3 Reverse Voltage - VR (V) 4 5 www.semtech.com RClamp0504S PROTECTION PRODUCTS Insertion Loss S21 (I/O to Pin 2) CH1 S21 LOG Insertion Loss S21 (I/O to I/O) 6 dB / REF 0 dB CH1 S21 LOG 6 dB / REF 0 dB 1: -0.1801 dB 900 MHz 1: -0.1063 dB 900 MHz 2: -0.6816 dB 1.8 GHz 2: -0.2660 dB 1.8 GHz 3: -3.0407 dB 2.448 GHz 0 dB 4 1 2 3 -6 dB 3: -0.5657 dB 2.5 GHz 0 dB 4: -3.3538 dB 2.5 GHz 1 -12 dB -18 dB -18 dB -24 dB -24 dB -30 dB -30 dB 1 MHz 10 MHz 100 MHz -36 dB 3 1 GHz GHz STOP 3000. 000000 MHz START . 030 MHz LOG START . 030 MHz 2008 Semtech Corp. 1 MHz 10 MHz START . 030 MHz Analog Crosstalk CH1 S21 2 -6 dB -12 dB -36 dB 3 100 MHz 3 1 GHz GHz STOP 3000. 000000 MHz ESD Clamping (+8kV Contact per IEC 61000-4-2) 20 dB /REF 0 dB STOP 3000. 000000 MHz Note: Data is taken with a 10x attenuator 4 www.semtech.com RClamp0504S PROTECTION PRODUCTS Applications Information Protection of Four Data Lines and Power Supply Line Device Connection Options for Protection of Four High-Speed Data Lines This device is designed to protect data lines by clamping them to a fixed reference. When the voltage on the protected line exceeds the reference voltage the steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Data lines are connected at pins 1, 3, 4 and 6. Pin 2 should be connected directly to a ground plane. The path length is kept as short as possible to minimize parasitic inductance. The positive reference is connected at pin 5. The options for connecting the positive reference are as follows: Protection of Four Data Lines Using Internal TVS Diode as Reference 1. To protect data lines and the power line, connect pin 5 directly to the positive supply rail (VCC). In this configuration the data lines are referenced to the supply voltage. The internal TVS diode prevents over-voltage on the supply rail. 2. In applications where the supply rail does not exit the system, the internal TVS may be used as the reference. In this case, pin 5 is not connected. The steering diodes will begin to conduct when the voltage on the protected line exceeds the working voltage of the TVS (plus one diode drop). 3. In applications where complete supply isolation is desired, the internal TVS is again used as the reference and VCC is connected to one of the I/O inputs. An example of this configuration is the protection of a SIM port. The Clock, Reset, I/O, and VCC lines are connected at pins 1, 3, 4, and 6. Pin 2 is connected to ground and pin 5 is not connected. Matte Tin Lead Finish Matte tin has become the industry standard lead-free replacement for SnPb lead finishes. A matte tin finish is composed of 100% tin solder with large grains. Since the solder volume on the leads is small compared to the solder paste volume that is placed on the land pattern of the PCB, the reflow profile will be determined by the requirements of the solder paste. Therefore, these devices are compatible with both lead-free and SnPb assembly techniques. In addition, unlike other lead-free compositions, matte tin does not have any added alloys that can cause degradation of the solder joint. 2008 Semtech Corp. 5 www.semtech.com RClamp0504S PROTECTION PRODUCTS Applications Information - Spice Model 0.7 nH RClamp0504S Spice Model R Clamp0504S Spice Parameters 2008 Semtech Corp. Parameter Unit D1 (LCR D) D2 (LCR D) D3 (T VS) IS Amp 1.29E-18 1.53E-16 1.78E-10 BV Volt 100 100 7.75 VJ Volt 0.83 0.81 0.59 RS Ohm 0.787 0.951 0.771 IB V Amp 1E-3 1E-3 1E-3 CJO Farad 1.0E-12 0.8E-12 111E-12 TT sec 2.541E-19 2.541E-19 2.541E-9 M -- 0.215 0.100 0.313 N -- 1.1 1.1 1.1 EG eV 1.11 1.11 1.11 6 www.semtech.com RClamp0504S PROTECTION PRODUCTS Outline Drawing - SOT-23 6L DIM A e1 2X E/2 A A1 A2 b c D E1 E e e1 L L1 N 01 aaa bbb ccc D N EI 1 E 2 ccc C 2X N/2 TIPS e B D aaa C A2 SEATING PLANE DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .057 .035 .000 .006 .035 .045 .051 .010 .020 .009 .003 .110 .114 .122 .060 .063 .069 .110 BSC .037 BSC .075 BSC .012 .018 .024 (.024) 6 0 10 .004 .008 .008 A H A1 C 1.45 0.90 0.00 0.15 .90 1.15 1.30 0.25 0.50 0.08 0.22 2.80 2.90 3.10 1.50 1.60 1.75 2.80 BSC 0.95 BSC 1.90 BSC 0.30 0.45 0.60 (0.60) 6 0 10 0.10 0.20 0.20 bxN bbb c GAGE PLANE C A-B D 0.25 L 01 (L1) SEE DETAIL DETAIL A A SIDE VIEW NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. Land Pattern - SOT-23 6L X DIM (C) G Z Y P C G P X Y Z DIMENSIONS MILLIMETERS INCHES (.098) .055 .037 .024 .043 .141 (2.50) 1.40 0.95 0.60 1.10 3.60 NOTES: 1. 2008 Semtech Corp. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 7 www.semtech.com RClamp0504S PROTECTION PRODUCTS Marking Ordering Information S54 Part Number Qty per Reel Reel Size RClamp 0504S.TCT 3,000 7 Inch Note: This is a lead-free RoHS/WEEE compliant device RailClamp and RClamp are marks of Semtech Corporation Tape and Reel Specification User Direction of feed A0 3.23 +/-0.05 mm B0 K0 3.17 +/-0.05 mm Tape Width B, (Max) D 8 mm 4.2 mm (.165) 1.5 + 0.1 mm - 0.0 mm 1.37 +/-0.05 mm D1 E 1.0 mm 0.05 1.750.10 mm F 3.50.05 mm K (MAX) P P0 P2 2.4 mm 4.00.1 mm 4.00.1 mm 2.00.05 mm T(MAX) 0.4 mm W 8.0 mm + 0.3 mm - 0.1 mm Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 2008 Semtech Corp. 8 www.semtech.com