INCH-POUND MS35058K 6 January 2006 SUPERSEDING MS35058J 15 November 1980 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE ONE POLE, SEALED TOGGLE This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the switch described herein shall consist of this specification and the latest issue of MIL-DTL-83731. FIGURE 1 Dimensions and configurations AMSC N/A FSC 5930 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z Check the source to verify that this is the current version before use. MS35058K NOTES 1. All dimensions are in inches. 2. For hardware and terminal screw detail specifications see supplement of MIL-DTL-83731. 3. Unless otherwise specifies, tolerance is .02 on two place decimals and .005 on three place decimals. FIGURE 1 Dimensions and configurations Continued REQUIREMENTS: All switches on this standard are designed so that the movement of the switch mechanism is opposite to that of the toggle lever. Maximum weight is 0.10 pounds. Endurance: Electrical 10,000 Cycles. Endurance: Mechanical 20,000 Cycles. Referenced documents shall be of the issue in effect on the date of invitation for bid. For design feature purposes, this standard takes precedence over procurement document referenced herein. Table I MS part numbers Former Ms Part No. MS Part No. Screw-Lug Terminal MS35058-21 MS35058-22 MS35058-23 MS35058-24 MS35058-25 MS35058-26 MS35058-27 MS35058-28 MS35058-29 MS35058-30 MS35058-31 MS35058-5 MS35058-4 MS35058-1 MS35058-3 MS35058-6 MS35058-7 MS35058-2 MS35058-8 - Solder-Lug Terminal 1/ MS35058-16 MS35058-9 MS35058-15 MS35058-12 MS35058-14 MS35058-17 MS35058-18 MS35058-13 MS35058-10 MS35058-11 MS35058-19 Former AN Part No. Former Jan Type Designation AN3021-1 AN3021-2 AN3021-3 AN3021-10 AN3021-12 AN3021-7 AN3021-11 AN3021-9 AN3021-8 AN3021-6 -- ST40 E ST42 E ST40 A ST42 A ST40D ST42D ST40F ST42F ST40G ST42G ST40B ST42B ST40C ST42C ST40H ST42H 1/ These MS part numbers are superseded by part number MS35058-21 thru MS35058-31, as applicable. By removing the screws and lockwashers from the applicable part, a switch with solder lug terminal is formed. 2 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z Check the source to verify that this is the current version before use. TABLE II: Detail Requirements Circuit with toggle lever in MS Part No. Keying Side Center Opposite Keying side On Off On MS35058-22 Off None On MS35058-23 On None On MS35058-24 None Off On MS35058-25 None MomOff On MS35058-26 MomOn None On MS35058-27 MomOn Off Mom-On MS35058-28 Momon Off None MS35058-29 MomOff None On MS35058-30 Momon None Off MS35058-31 Momon Off On LampLoad Circuit Resistive Circuit Inductive Lamp Load Circuit Resistive Circuit Inductive Circuit Alternating current 60 Hertz Resistive Circuit Inducti ve Circuit Lamp Load Circuit 28 V 28 V 125 V 250 V 28 V 125 V 250 V 115 V 115 V 115 V 115 V 220 V 115 V Lamp Load Volts 7 25 ---- ----- 15 ----- ----- 3 10 10 10 ----- 10 ---- 5 20 ----- ----- 10 ----- ----- 2 10 7 10 ----- 7 ------- MS35058K 3 MS35058-21 Current Capacity (amperes per pole) Alternating Current 400 Hertz Direct Current Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z Check the source to verify that this is the current version before use. MS35058K Referenced documents MIL-DTL-83731 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Army - CR Navy - AS Air Force - 11 DLA - CC Preparing activity: DLA - CC Project (5930-2005-020) Review activities: Army - AV, MI Navy - EC Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil/. 4 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z Check the source to verify that this is the current version before use.