AMSC N/A FSC 5930
MS35058K
6 January 2006
SUPERSEDING
MS35058J
15 November 1980
DETAIL SPECIFICATION SHEET
SWITCH, TOGGLE ONE POLE, SEALED TOGGLE
This specification is approved for use by all
Departments and Agencies of the Dep artment of Defense.
The complete requirements for acquiring the switch described herein shall consist of this specification and
the latest issue of MIL-DTL-83731.
FIGURE 1 Dimensions and config urations
INCH-POUND
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z
Check the source to verify that this is the current version before use.
MS35058K
2
NOTES
1. All dimensions are in inches.
2. For hardware and terminal screw detail specifications see supplement of MIL-DTL-83731.
3. Unless otherwise specifies, tolerance is ± .02 on two place decimals and ± .005 on three place
decimals. FIGURE 1 Dimensions and config urations Continued
REQUIREMENTS:
All switches on this standard are designed so that the movement of the switch mechanism is opposite
to that of the toggle lever.
Maximum weight is 0.10 pounds.
Endurance: Electrical 10,000 Cycl es.
Endurance: Mechanical 20,000 Cycles.
Referenced documents shall be of the issue in effect on the date of invitation for bid.
For design feature purpose s, this stan dard takes precedence over procurement document referenced
herein. Table I MS part numbers
Former Ms Part No.
MS Part No. Screw-Lug Terminal Solder-Lug Terminal
1/
Former
AN Part No. Former Jan Type
Designation
MS35058-5 - AN3021-1 ST40 E
MS35058-21 - MS35058-16 - ST42 E
- - AN3021-2 ST40 A
MS35058-22 - MS35058-9 - ST42 A
MS35058-4 - AN3021-3 ST40D
MS35058-23 - MS35058-15 - ST42D
MS35058-1 - AN3021-10 -
MS35058-24 - MS35058-12 - -
MS35058-3 - AN3021-12 - MS35058-25
- MS35058-14 - -
MS35058-6 - - ST40F MS35058-26
- MS35058-17 - ST42F
MS35058-7 - AN3021-7 ST40G MS35058-27
- MS35058-18 - ST42G
MS35058-2 - AN3021-11 - MS35058-28
- MS35058-13 - -
- - AN3021-9 ST40B MS35058-29
- MS35058-10 - ST42B
- - AN3021-8 ST40C MS35058-30
- MS35058-11 - ST42C
MS35058-8 - AN3021-6 ST40H
MS35058-31 - MS35058-19 -- ST42H
1/ These MS part numbers are supersed ed by part number MS35058-21 thru MS35058-31, as applicable.
By removing the screws and lockwashers from the applicable part, a switch with solder lug terminal is
formed.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z
Check the source to verify that this is the current version before use.
TABLE II: Detail Requirements
Current Capacity (amperes per pole)
Circuit with toggle lever in Direct Current Alternating Current 400 Hertz Alternating current 60 Hertz
Lamp-
Load
Circuit
Resistive Circuit Inductive Lamp
Load
Circuit
Resistive
Circuit Inductive
Circuit
Resistive
Circuit
Inducti
ve
Circuit
Lamp Load
Circuit
MS Part No. Keying
Side Center Opposite
Keying
side
28 V 28
V 125
V 250
V 28
V 125
V 250
V 115 V 115 V 115 V 115
V 220
V 115
V Lamp Load
Volts
MS35058-21 On Off On
MS35058-22 Off None On 7 25 ---- ----- 15 ----- ----- 3 10 10 10 ----- 10 ----
MS35058-23 On None On
MS35058-24 None Off On
MS35058-25 None Mom-
Off On
MS35058-26 Mom-
On None On
MS35058-27 Mom-
On Off Mom-On
MS35058-28 Mom-
on Off None 5 20 ----- ----- 10 ----- ----- 2 10 7 10 ----- 7 -------
MS35058-29 Mom-
Off None On
MS35058-30 Mom-
on None Off
MS35058-31 Mom-
on Off On
MS35058K
3
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z
Check the source to verify that this is the current version before use.
MS35058K
4
Referenced documents
MIL-DTL-83731
Marginal notations are not used in this revision to identify changes with respect to the previous issue due
to the extent of the changes.
Custodians: Preparing activity:
Army – CR DLA – CC
Navy – AS
Air Force – 11 Project (5930-2005-020)
DLA – CC
Review activities:
Army – AV, MI
Navy – EC
Air Force – 99
NOTE: The activities listed above were interested in this documen t as of the date of this document.
Since organizations and respo nsibilities can change, you sho uld verify the currency of the information
above using the ASSIST Online database at http://assist.daps.dla.mil/.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:10Z
Check the source to verify that this is the current version before use.
