CT6S-1P4 - AUTONICS - Datasheet.Live

J-8

CT Series

DAQMaster(integrated device management program)

Upgraded functions

DIN W48×H48mm, W72×H36mm, W72×H72mm counter/timer

● DAQMaster is a integrated device management program for convenient

management of parameters and multiple device data monitoring.

● Visit our website (www.autonics.com) to download user manual and

integrated device management program.

Item

Digit

Size

Output

Power supply

Communication 출출 출출출 출

Ordering information

CT 2P6 M 4 T-

No mark None

T RS 485

4 100-240VAC 50/60㎐

2 24VAC 50/60㎐ / 24-48VDC

4 9999(4digit)

6 999999(6digit)

CT Counter/Timer

2P Dual preset

1P Single preset

I Indicator

S DIN W48×H48mm

Y DIN W72×H36mm

M DIN W72×H72mm

※A shaded ( ) part is upgraded or added function.

< DAQMaster screen >

※4digit type does not exist

in the indicator type.

Upgrade

● Available to set 6 digits(0.00001 to 999999) prescale value

(4digit : 0.001 to 9999)

● Built-in Modbus communication function(Communication model)

● Available to set the One-Shot output time in 10ms.

(0.01sec. to 99.99sec.)

● Increase contact capacity to 5A(CTS, CTM Series)

● Available to set Count Start Point.(Initial value)

● Improved to select memory protection function in the indicator

● Added BATCH counter function(CTM Series)

● Added Counter Up-1 / Up-2 / Down-1 / Down-2 input modes

● Added Counter TOTAL / HOLD operation modes in the indicator

● Added Timer TOTAL / HOLD / On Time Display operation

modes in the indicator

● Added Timer INT2 / NFD / NFD.1 / INTG output modes

● Added Timer range 999.999s / 9999m59 / 99999.9h

Please read “Caution for your safety” in operation

manual before using.

Item Minimum requirements

System IBM PC compatible computer with Intel Pentium

Ⅲ or above

Operating system

Microsoft Windows 98/NT/XP/Vista/7

Memory 256MB or more

Hard disk More than 1GB of free hard disk space

VGA 1024×768 or higher resolution display

Others RS-232 serial port(9-pin), USB port

J-9

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Communication specification

Specications

Series CTS CTY CTM

Digit 4 6 6 6

Model

Dual Preset CT4S-2P CT6S-2P CT6Y-2P CT6M-2P

Single Preset CT4S-1P CT6S-1P CT6Y-1P CT6M-1P

Single Preset

CT6S-1 CT6Y-1 CT6M-1

Digit

Size

Single Preset 11mm 10mm 10mm 13mm

Single Preset 8mm 7mm 7mm 9mm

Power

Supply

Single Preset 100-240VAC 50/60Hz

Single Preset 24VAC 50/60Hz / 24-48VDC

Allowable voltage range

90 to 110% of rated voltage(AC Power type)

Power

consumption

Single Preset Max. 12VA

Single Preset AC: Max. 10VA / DC: Max. 8W

INA/INB Max. counting speed Selectable 1cps / 30cps / 1kcps / 5kcps / 10kcps

Min. input

signal width

Counter Reset signal : Selectable 1ms, 20ms

Timer INA, INB RESET : Selectable 1ms, 20ms

INA, INH, RESET, INHIBIT, BATCH

RESET : Selectable 1ms, 20ms

Input Selectable voltage input or No-voltage input

[Voltage input] Input impedance is 5.4kΩ, 'H' level : 5-30VDC, 'L' level : 0-2VDC

[No-voltage input] Short-circuit impedance : Max. 1kΩ, Residual voltage : Max. 2VDC

One-shot output Count, timer : Selectable 0.01s to 99.99s

Control

output

With-

out

com.

Contact

output Dual preset : SPST(1a) 2EA

Single preset : SPDT(1c) 1EA Dual preset : SPST(1a) 1EA, SPDT(1c) 1EA

Single preset : SPDT(1c) 1EA

Solid state

output Dual preset : 1NPN open collector

Single preset : 1NPN open collector

Dual preset:3NPN open collector

Single preset:2NPN open collector

With-

out

com.

Contact

output Dual preset : SPST(1a)2EA

Single preset : SPDT(1c)1EA

Dual preset: SPST(1a), SPDT(1c)

Single preset: SPDT(1c)

Solid state

output

Dual preset: -

Single preset:1NPN open collector

Dual preset:2NPN open collector

Single preset:2NPN open collector

With-

out

com.

Contact

output 250VAC 5A resistive load 250VAC 3A resistive load 250VAC 5A resistive load

Solid state

output 30VDC Max. 100mA Max.

External sensor power 12VDC ±10%, 100mA Max.

Memory retention 10years(When using non-volatile semiconductor memory type)

Timer

Repeat error

Power ON Start : Max. ±0.01% ±0.05 sec

Signal Start : Max. ±0.01% ±0.03 sec

SET error

Voltage error

Temperature error

Insulation resistance Min. 100MΩ(500VDC Megger)

Dielectric strength 2,000VAC 50/60Hz for 1minute

Noise strength (AC Power) ±2kV the square wave noise(pulse width:1㎲) by the noise simulator

Vibration Mechanical 0.75mm amplitude at frequency of 10 to 55(for 1 min.)Hz in each of X, Y, Z directions for 1 hour

Malfunction 0.5mm amplitude at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 10 minutes

Shock Mechanical 300m/s²(approx. 30G) in each of X, Y, Z directions for 3 times

Malfunction 100m/s²(approx. 10G) in each of X, Y, Z directions for 3 times

Relay

Life cycle

Mechanical Min. 10,000,000 operations

Electrical Min. 100,000 operations

Protection IP65(Front panel only)

Environment

Ambient

temperature -10 to 55℃, storage : -25 to 65℃

Ambient

humidity 35 to 85%RH, storage : 35 to 85%RH

Approval

Unit weight Approx. 159g Approx. 149g Approx. 253g

※Environment resistance is rated at no freezing or condensation.

Protocol Modbus RTU(16bit CRC)

Connection method

RS485

Application standard

Compliance with EIA RS485

Number of connections

31, it is available to set address 1 to 127

Communication method

Half Duplex

Synchronous method

Asynchronous

Communication distance

within max. 800meter

Communication speed

2,400/4,800/9,600/19,200/38,400bps(Factory default : 9,600bps)

Response waiting time

5 to 99ms(Factory default : 20ms)

Start bit 1bit(Fixed)

Data bit 8bits(Fixed)

Parity bit None, Even, Odd(Factory default : None)

Stop bit 1, 2bit(Factory default : 2bit)

J-10

CT Series

Connections

CT S-2P

CT S-1P

CT6S-I

CT6Y-2P

CT6Y-1P

Be careful that connections are different

between communication model and

non-communication model when wiring.

RS485

OUT

RS485

A(+)

B(-)

12VDC 100mA

INB / INH

INA

INB / INH

12VDC 100mA

INA

INB / INH

12VDC 100mA

INA

INB / INH

12VDC 100mA

INA

INB / INH

12VDC 100mA

INB / INH

INA

12VDC 100mA

INB / INH

INA

12VDC 100mA

INB / INH

INA

12VDC 100mA

INB / INH

INA

12VDC 100mA

INB / INH

INA

250VAC 5A

RESISTIVE

250VAC 5A

RESISTIVE

250VAC 5A

RESISTIVE

250VAC 5A

RESISTIVE LOAD

250VAC 3A

RESISTIVE LOAD

250VAC 3A

RESISTIVE LOAD

250VAC 3A

RESISTIVE LOAD

250VAC 3A

RESISTIVE

250VAC 3A

RESISTIVE

250VAC 3A

RESISTIVE LOAD

SOLID

STATE OUT

30VDC

100mA

SOLID

STATE OUT

30VDC

100mA

SOLID

STATE OUT

30VDC

100mA

250VAC 5A

RESISTIVE LOAD

NCNC

NOCOM

COM

COMCOM

OUT

OUT2 OUT1 OUT2

OUT OUT

COMNC

NONO

250VAC 5A

RESISTIVE

OUT2

30VDC

100mA

OUT

30VDC

100mA

OUT

OUT2

OUT1

RESET

0VDC

RESET

0VDC

RESET

0VDC

0VDC RESET

0VDC RESET0VDC RESET

0VDC RESET

RESET

0VDC

RESET

0VDC

RESET

0VDC

※1※1

※1

※1※1

※1

CT S-2P T

CT S-1P T

CT6S-I T

CT6Y-2P T

CT6Y-1P T

J-11

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

CT6Y-I

CT6M-2P

CT6M-1P

CT6M-I

CT6Y-I T

CT6M-2P T

CT6M-1P T

CT6M-I T

12VDC 100mA

INB

INA

12VDC 100mA

INB

INA

12VDC 100mA

INB

INA

12VDC 100mA

INB

INA

INB / INH

12VDC 100mA

INA

INB / INH

12VDC 100mA

OUT2

OUT1

OUT2

OUT

0VDC RESET 0VDC RESET

※1

※2

※2※2

※1

RS485

250VAC 5A

RESISTIVE

LOAD

250VAC 5A

RESISTIVE

LOAD

250VAC 5A

RESISTIVE

LOAD

30VDC

100mA

30VDC

100mA

INHIBIT

RESET

INHIBIT

RESET

INHIBIT

RESET

INHIBIT

RESET

BATCH

0VDC

0VDC 0VDC

BATCH RESET

SOLID STATE OUT

NCCOM

COM

B(-)

A(+)

※1: Source

- AC Power: 100-240VAC 50/60Hz

- AC/DC Power: 24-48VDC, 24VAC 50/60Hz

※2: INHIBIT Signal

- Counter operation: If INHIBIT signal is applied,

count input will be prohibited.

- Timer operation: If INHIBIT signal is applied, time

progressing will stop.(HOLD)

12VDC 100mA

INB

INA

OUT

※2

※1

250VAC 5A

RESISTIVE

LOAD

30VDC

100mA

INHIBIT

RESET

OUTPUT

COMMON BATCH

0VDC

BATCH RESET

SOLID STATE OUT

COM

NO NO

12VDC 100mA

INB

INA

OUT2

OUT1

OUT1 OUT2

※1

※2

250VAC 5A

RESISTIVE

LOAD

250VAC 5A

RESISTIVE

LOAD

30VDC

100mA

INHIBIT

RESET

OUTPUT

COMMON BATCH

0VDC

BATCH RESET

SOLID STATE OUT

NCCOM COM

NO NO

J-12

CT Series

CTS Series

CTS Series CTY Series CTM Series

CTY Series

CTM Series

72 77

6 2

72 10

Min. 91

Min. 55

Min. 62

9010

Min. 40

30 45

Min. 91

68+0.7

68 +0.7

45.5 +0.5

31.5

+0.6

Dimensions

Parts description

● Panel cut-out

● Bracket

1. Count indicator(Red LED)

- Run mode

: Count mode-Indicates count value.

Timer mode-Indicates time progressing.

- Function setting mode

: Indicates function setting mode.

2. Preset value indicator (Yellow-Green LED)

- Run mode: Indicates preset value.

- Function setting mode: Indicates setting value1.

3. Key Lock : Lights when setting key lock.

4. The operation of counter indicator

5. The operation of timer indicator

TMR LED flashes when the timer is operating.

TMR LED lights when the operating time stops.

6. Check preset value and display change of it

PS1 LED lights when checking or changing the setting value1

PS2 LED lights when checking or changing the setting value2.

7. Output(OUT1, OUT2) indicator

OUT1 lights when output1 is on.

OUT2 lights when output2 is on.

8. Reset key

By pressing RST key in Run mode, the count value is initialized and

output is returned.

By pressing

RST

key in BATCH counter mode,BATCH count valu

resets.

9. Mode key

By pressing

key for 3sec (parameter setting)/ 5sec (communication)

in RUN mode, it moves to function setting mode.

- By pressing

key in function setting mode, select function setting

mode. By pressing MD key over 3 sec., it moves to Run mode.

- By pressing

key over 1 sec. in function setting checking mode,

moves to Run mode.

10. Set key

≪ :

To enter into setting value(PS1, PS2) change status and shift digit

of setting value(PS1, PS2).

≫

To decrease setting value in setting value change mode, change

setting value in function setting mode, move down checked

value in function setting check mode.

≫

To increase setting value in setting value change mode, change

setting value in function setting mode, move up checked value in

function setting check mode. By pressing MD key over 1 sec.

in Run mode, enters into function setting check mode.

11. BATCH key

By pressing BA key in run mode to enter into BATCH counter

indication mode.

12. BATCH output indicator(red LED)

13. BATCH setting value checking and changing indicator

(yellow-green LED)

Lights when checking and changing BATCH setting value.

(unit:mm)

Model Changed Notice

CT6Y-1P

PS2→PS

OUT2→OUT

There are no

PS1, OUT1

LEDs.

CT6S-1P

CT4S-1P

CT6M-1P

CT6Y-I

PS2→PS

There are no

PS1, OUT1

OUT2 LEDs.

CT6S-I

CT6M-I

※The indicator type does not exist

in CT4S model.

J-13

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

3. Select input logic by using input logic switch(SW1)

inside Counter/Timer.

1. The power must be cut off.

2. Detach the case from the body.

(CTS, CTY Series)

Input connections

Input logic Selection[No-voltage input(NPN)/Voltage input(PNP)]

No-voltage input(NPN)

Voltage input(PNP)

● Solid-state input(Standard sensor : NPN output type sensor) ● Contact input

● Solid-state input(Standard sensor : PNP output type sensor) ● Contact input

※1: INA, INB/INH, RESET, INHIBIT, BATCH RESET input part

※2: Counting speed: 1 or 30cps setting(Counter)

※1: INA, INB/INH, RESET, INHIBIT, BATCH RESET input part

※2: Counting speed: 1 or 30cps setting(Counter)

* Case detachment

Squeeze toward ① and pull toward ② as shown

in picture.

Please check if the power is cut off.

①

②

①

5.4Ω

5.4㏀

5.4Ω

5.4㏀5.4Ω

5.4Ω

+12V

+12V +12V

+12V

0V 0V

0V 0V 0V

Inner circuit

of input part

Inner circuit

of input part

Inner circuit

of input part

Inner circuit

of input part

Inner circuit

of input part

Inner circuit

of input part

Sensor

(NPN output)

(PNP output)

(NPN open collector output)

(PNP open collector output)

Sensor

Brown

Black

※1

※2

Blue

Counter/Timer

CT Series

Counter/Timer

CT Series

Counter/Timer

CT Series

Counter/Timer

CT Series

Counter/Timer

CT Series

Counter/Timer

CT Series

● Select No-voltage

input(NPN)

● Select voltage

input(PNP)

PNPPNP

NPN

(Factory default)

NPN

4. Push a case in the opposite direction of 2-②.

5. Then apply the power to Counter/Timer.

J-14

CT Series

Output connections

Factory default

Error display

Contact output Solid-state output

※Use proper load not to exceed the capacity. ※

Use proper load and power for load not to excess ON/OFF

capacity(30VDC Max. 100mA max.) of solid state output.

※Be sure not to apply reverse polarity of power.

※1: When use inductive load(Relay etc), surge absorber

(Diode, varistor etc) must be connected between both

sides of the load.

※1

Counter/Timer

CT Series

Counter/Timer

CT Series

Load

(+)

(

)

Power

for load

(DC)

(Power of load)

Error display Errors Output status How to return

Failed in data loading

for exsiting setting

values

OFF Power on again

Parameter Factory default

Input mode (ㅑIN)UP/Down-C (UD-C)

Output mode (OUtM) F (F)

CPS (CPS)30cps (30)

Indication mode (indicator type)(DSpM) TOTAL (TOTAL)

OUT2 output time (OUt2)Hold (HOLD)

OUT1 output time (OUt1)100ms (0)10)

Decimal point (DP)------

Min. reset time (RST)20ms (20)

Input logic (SIG)NPN (NPN)

Prescale decimal point (ScDP)6digit type : -.-----, 4digit type : -.---

Prescale value (SCL)6digit type : 1.00000，4digit type : 1.000

Start Point setting (STRT)000000

Counting memory (DATA)Clear (SLR)

Lock key (LOCK)Lock off (lOFF)

Preset value 1 (PS1) 1000 (1000)

Preset value 2 (PS2) 5000 (5000)

Time range (HOUR/MIN/SEC)6Digit type: 0.001s-999.999s, 4Digit type: 0.001s-9.999s

Up/Down mode (U-D)UP (UP)

Indication mode(Indicator type)(DSpM) TOTAL (TOTAL)

Memory protection(Indicator type)

(DATA)CLEAR (SLR)

Output mode (OUtM)OND (OND)

OUT2 output time (OUT2)Hold (HOLD)

OUT1 output time (OUT1)100ms (0)10)

Input logic (SIG)NPN (NPN)

Input signal time (ImT)20ms (20)

Lock key (LOCK)Lock off (lOFF)

Preset value 1 (PS1) 1000 (1000)

Preset value 2 (PS2) 5000 (5000)

Communication address (ADDR)01 (001)

Communication speed (BPS)9600bps (96)

Communication parity (PRTY)NONE (NONE)

Communication stop bit (STP)2 (2)

Response waiting time (RSWT)20ms (20)

Communication writing (COmY)Enable (ENA)

CounterTimer

Communication

PS1○

PS2○

EEP

FAIL

J-15

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Change of BATCH

setting value.

Change of

preset

Function setting

check mode

Operations and functions

Change of preset(Counter/Timer)

Function setting check mode

Change of BATCH setting value

Switching display function in preset indicator

Reset

● Even if changing the preset value, input operation and output control will continue. In addition, the preset value could

be set to 0 and 0 preset value turns ON. According to output mode, preset value could not be set to 0. (When setting to 0,

preset value "0" will flash 3 times.)

● Setting value of function setting mode can be confirmed using the and keys.

● Setting value 1(PS1) and setting value 2(PS2) are displayed each time pressing key in dual preset model.

(In timer, it is available for output mode.)

In BATCH counter indication mode, 'BATCH counter value' is displayed in count indicator and 'BATCH counter

setting value' is displayed in preset indicator.

If pressing key in Run mode, it will enter into BATCH counter indication mode.

● In Run mode or function setting mode, if key or applying the signal to the RESET terminal on the back side,

present value will be initialized and output will maintain off status. When selecting voltage input(PNP), short no. 10

and no. 12 terminals, or when selecting no-voltage input(NPN), short no. 11 and no. 12 terminals to reset.

※1. If no key is touched for 60 sec., the counter will

return to RUN mode without being restored.

※BATCH counter is

available for

CT6M-1P/2P only.

In Run mode, it enters into the

preset value setting mode

using key. 'PS1' LED lights

and first digit of preset value

flashes.

It enters into

settingvalue change

mode using key.

(BA.S lights, first digit

of setting value flashes.)

BATCH value is set to '200'

using , and keys,

then press key to complete

BATCH setting value and

move to BATCH counter

indication mode.

The preset value is set to ' '

using , and keys, then

press key to enter into the

PS2 setting mode.

The preset value is set to '200'

using , and keys, then

press key to complete PS2

setting and return to Run mode.

※ Press key to save set value after changing the setting value. Then, it moves to next parameter or returns

to RUN mode. However, if no key is touched for 60 sec., it will return to RUN mode without being saved.

BATCH RESET

RESET

BATCH counter

indication mode

3sec.: Enters into parameter 1 group

5sec.: Enters into parameter 2 group

Function

setting mode

3sec.

3sec. 5sec.

※1

1. 2.

2. 3.

1sec.

RUN

mode

BATCH Counter(For CT6M-1P /CT6M-2P model only)

J-16

CT Series

BATCH counter operation

BATCH counting operation

BATCH output

BATCH reset input

Application of BATCH counter function

● BATCH counting value is increasing until BATCH reset signal applied. BATCH counting value will be circulated when it is

over 999999.

1) BATCH counting operation in Counter : Counts the number of reaching setting value of CT6M-1P or reaching dual

setting value of CT6M-2P

2) BATCH counting operation in Timer: Counts the number of reaching setting time.

(In case of "FLK" output mode, count the number of reaching T.off setting time

and T.on setting time.)

● If input signal is applied while changing BATCH setting value, counting operation and output control will be performed.

●

If BATCH count value equals to BATCH setting value, BATCH output will be ON and maintain ON status

until BATCH reset

signal is applied.

●

When the power is cut off then resupplied in status of BATCH output is ON, BATCH output maintains ON

status until

BATCH reset signal is applied.

● If pressing reset button or applying the signal to BATCH reset terminal on the back side panel, BATCH counting value will

be reset. When selecting voltage input(PNP), short no. 10 and no. 14 terminals, or when selecting no-voltage input(NPN),

short no. 11 and no. 14 terminals to reset.

● When BATCH reset is applied, BATCH counting value maintains at 0 and BATCH output maintains in the OFF status.

OFF

Preset output

Batch Reset

999999

Batch setting value

Power

BA.O LED

Batch

output

● Counter

In case, put 5 products in a box then pack the boxes when

they reaches to 200.

- Counter preset setting value="5", BATCH setting

value="200"

- When the count value of counter reaches to the preset

value "5", the control output(OUT) will be on, and at

this time the count value of the BATCH counter will be

increased by "1". The control box which is received the

control output (OUT) repeatedly controls conveyor to

move the full box and to place the next empty box for

standby. When the BATCH count value reaches to "200",

BATCH output will be ON. Then the control box stops

conveyor and provides a control signal for packing.

● Timer

Fills milk into the bottle for 3sec.(setting time) When 500

bottles are filled, BATCH counting finish lamp is turned on.

(Setting time : 3sec., BATCH setting value : 500)

BATCH output

Operation valve

(Open valve

for 3sec.)

Control

output

Control the

operation valve

Bottle sensing

sensor

CT6M-

1P4

Control

box

Count input BATCH output

Control

output

(OUT)

CT6M-1P4

Preset value = 5

Control box

Current BATCH count value = 3

Third

box

Second

box

First

box

Control signal

for conveyor

Control signal

for packing

BATCH output

lamp

BATCH counting

nish lamp

Productivity :

500bottels

Lamp on when

it is completed.

J-17

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

3sec. 3sec. 5sec. 3sec.

Memorize

counting value

(DATA)

Communication

OUT2 output time

(OUT2)

OUT1 output time

(OUT1)

Decimal point

(DP)

Start Point value

(STRT)

Run mode

Parameter group2

(GRp2)

Min. reset time

(RST)

Prescale value

(RST)

Input logic

(SIG)

Prescale decimal

point

(ScDP)

Memorize counting value

(DATA)

Lock key

(LOCK)

Output mode

(OUtM)

OUT2 output time

(OUT2)

OUT1 output time

(OUT1)

Input logic

(SIG)

Input signal time

(InT)

Lock key

(LOCK)

Parameter group1

(GRp1)

Input mode

(IN)

Output mode

(ㅑㅑㅑOUtM)

Indication mode

(DSpM)

Max. counting speed

(CPS)

Counter/Timer

(C-T)

Counter

(COUN)Timer

(T1ME)

※1

※3※3

※3

※2

※3

※1

※3

※2

※3

Up/Down mode

(U-D)

Time range

(HOUR/MIN/SEC)

Indication mode

(DSpM)

Com. address

(ADDR)

Com. speed

(BPS)

Com. parity

(PRTY)

Com. stop bit

(STP)

Response

waiting time

(RSwT)

Com. writing

(COmW)

Function setting mode

Flow chart for function setting mode

※If changing setting value of parameter group1, display value and output will be initialize.

※Press key over 3sec./5sec. in RUN mode to enter into parameter 1 group/ parameter 2 group.

Press key over 3 sec. in function setting mode to return RUN mode.

※Input operation and output control can be set in function setting mode.

※If changing set value of ※3 marked parameters in function setting mode, OUT1 and OUT2 output will be turned OFF and

then the current value is reset.

※Parameter 2 group is not available to non-communication models.

※1: Indicator

※2: Output type

※3: If changing the setting

value of function, OUT1,

OUT2 will turn OFF and

return to Run mode, then

present value resets.

※Counter

- Single preset model has no "OUT1 output setting time" setting function

mode and OUtT is displayed in "OUT2 output time" setting function mode.

- In case of DN, DN-1, DN-2 input mode, there is no "Start Point value" setting

function mode.

- In case of

output mode, there is no "OUT2 output time" setting function

mode.(Fixed to HOLD)

- In case of S, T or D output mode, there is no "OUT2 output time" setting

function mode.

※Timer

- In case of

FLk1

FLk2

INtG

output mode and

OND

OND1

OND2

output

mode of single preset model,

OUtT

is displayed in "OUT2 output time" function

setting mode and there is no "OUT1 output time" function setting mode.

- The output modes except for

OND

ONd1

ONd2

and INt2

output mode there is no

"OUT1 output time" function setting mode.

J-18

CT Series

Parameter setting(Counter)

※1. Explanation of decimal point and prescale decimal point setting

- Decimal point setting : Set decimal point of the display value on front indicator.

- Prescale decimal point setting : Set prescale decimal point of counting regardless of decimal point of display value

on front indicator.

( key: To select setting mode, or key: To change setting value)

Setting mode How to set

Counter/Timer

ㅑㅑC-T COUN TIME

Input mode

UD-C UP UP-1 UP-2 DN DN-1 DN-2 UD-A UD-B

Output mode

OUtM

Indication mode

DSpM

Max. counting speed

CPS 30 1K SY 10K 1

OUT2 output time

OUT2

OUT1 output time

OUT1

※1

Decimal point

Min. reset time

RST 1 20

Input logic

SIG

※1

Prescale

decimal point

ScDP

● 6digit type

● 4digit type

Prescale value

SCL

Start Point Value

STRT

Memory protection

DATA CLR REC

Lock key

LOCK

LOFF LOc1

LOc3 LOc2

※Set OUT1 one-shot setting time

※Time range: 0.01 to 99.99 sec., Hold

※HOLD is displayed by pressing key 4 times.

※Set OUT2 one-shot output time.

※Setting range: 0.01 to 99.99 sec.

※It does not appear if F, N output mode is selected.

※In case of the indicator, indicate mode selection (DSpM)is displayed.

※It is added that the function which can set the preset value when selecting

HOLD.(Refer to J-22 page 'Counter operation of the indicator'.)

※CONE: COUNTER

TIME: TIMER

※If output mode is set to D when max. counting

speed is set to 5Kcps, 10Kcps, max. counting

speed is automatically set to 30cps. (Factory

default setting)

※Counting speed is that of one by one(1:1) duty ratio of INA or INB input signal,

and it is applied in INA and INB at thesame time.

※In case of setting D in output mode, you can choose 1cps, 30cps, 1Kcps.

: To shift the ashing digit.

: To change the prescale value.

: To shift the ashing digit.

: To change the Start Point value.

※Setting range of prescale value

6digit type: 0.00001 to 99999.9

4digit type: 0.001 to 999.9

※Refer to the J-20 page ' Prescale function'.

※

Setting range of Start Point value (Connected with decimal point setting)

6digit type: 0.00000 to 999999

4digit type: 0.000 to 9999

※Refer to the J-20 page ' Start Point function'.

※CLR: Initializes count value when power is off.

※REC : Memorizes count value at the moment of power off.

※LOFF:Cancellation of the lock mode.

LOc1: Locks key.

LOc2: Locks , , keys.

LOc3: Locks , , , keys.

※Setting the decimal point is applied same to counting

value and setting value.

※Set the min. external RESET signal width.

※Check input logic value(PNP, NPN).

NPN: No-Voltage input

PNP: Voltage input

※Prescale decimal point position is not set below the decimal

point setting digits (DP).

unit: ms

: To shift ashing digit position of OUT2

output time value.

: To change OUT2 output time value.

: To shift ashing digit position of OUT1

output time value.

: To change OUT1 output time value.

● UP, UP-1, UP-2 or DN, DN-1, DN-2 input mode

F N C R K P Q A

● UD-A, UD-B, UD-C input mode

F N C R K P Q A S T D

● In case of the indicator

HOLD TOTAL

● 6digit type

------ -----.- ----.-- ---.--- --.---- -.-----

● 4digit type

---- ---.- --.-- -.---

※In case that output mode is F, N there is no "OUT2 output time" setting mode. (Fixed to HOLD)

J-19

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

counting

No counting

n-1

n-2

n-3

n-4

n-5

n-6 n-7

Ⓐ

INA

INB

Count

value

Count

value

Count

value

Count

value

Count

value

Count

value

Count

value

Ⓐ

Ⓐ Ⓐ Ⓐ

Ⓐ

012

32123

Input operation mode(Counter)

Input mode Count chart Operation

(UP)

※If INA is counting input, INB is

inhibition input.

If INB is counting input, INA is

inhibition input.

UP-1

(Up-1)

※Counts when INA input signal is up.

()

※INA: Counting input

※INB: Inhibition input

UP-2

(Up-2)

※Counts when INA input signal is

down. ( )

※INA: Counting input

※INB: Inhibition input

(Down)

※If INA is counting input, INB is

inhibition input.

If INB is counting input, INA is

inhibition input.

DN-1

(Down-1)

※Count when INA input signal is up.

()

※INA: Counting input

※INB: Inhibition input

DN-2

(Down-2)

※Counts when INA input signal is

down. ( )

※INA: Counting input

※INB: Inhibition input

UD-A

(Up/Down-A)

※INA: Counting input

INB: Counting command input

※When INB is L, counting Up.

When INB is H, counting Down.

INA

INB

J-20

CT Series

Input mode Count chart Operation

ㅑㅑUD-B

(Up/Down-B)

※INA: Up counting input

INB: Down counting input

※When both INA and INB are applied

to L->H, it will remain previous

counting value.

UD-C

(Up/Down-C)

※When use A,B phase of encoder

with connecting to INA, INB, please

set counter input mode(

) as

phase different input(

UD-C

B B B B

INA

INB

Count

value

Count

value

3323

Input operation mode(Counter)

Prescale function(Counter)

Start point function(Counter)

※ⓐ signal width should be over min. signal width and ⓑ signal width should be over a half min. signal width.

If not, ±1 will occur.

This function is to set and indicate calculated unit for actual length, liquid measure, position etc. It is called "Prescale value"

for measured length, measured liquid, measured position, etc per 1 pulse.

For example, P is the number of pulses per 1 revolution of a rotary encoder and L is the desired length to be measured.

Prescale value is [the desired length (L)]/[the number of pulses (P) per 1 revolution of the rotary encoder.].

It is the length per 1 pulse of a rotary encoder.

This function is that start point value works as initial value when on counting mode.

● In case of

DN-1

DN-2

in timer input mode, it is not available.

● When reset is applied, the present value is initialized to start point.

● After count up in

After count up in

To control conveyor position in 0.1mm, set the decimal point to tenth place(-----.-) in decimal point setting mode(DP) and

set the prescale decimal point to thousandth place(---.---) in prescale decimal point setting mode(ScDP)Then set prescale

value "0.069" in prescale setting mode (

SCL

Ex) Control length by the counter and the rotary encoder

※The meaning of "H" and "L" ※Min. signal width by counting speed

High

Low

※Ton, Toff : Min. signal width

INA

(INB) ON

Ton

Toff

ONOFF OFF

Rotary encoder

Cutter

Counter

Motor

Motor controlling

system

Roller

[In case of 22mm diameter(D) of roller connected

with the encoder of 1,000 pulse]

● Prescale value = π × Diameter of the roller(D)

The number of pulses per

1 revolution of the encoder

= 3.1416 × 22

1000

= 0.069mm/pulse

Voltage input (NPN)

No-Voltage input (PNP)

H 5-30VDC Short circuit

L 0-2VDC Open

Counting

speed

Min. signal

width

1cps 500㎳

30cps 16.7㎳

1kcps 0.5㎳

5kcps 0.1㎳

10kcps 0.05㎳

J-21

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

RESET

999999

PRESET

OUT1

OUT2

(OUT)

Output operation mode(Counter)

※The single preset type output(OUT) is operated as OUT2 of dual preset type.

※OUT1 output could be set to 0 in all modes and 0 value output turns ON.

※OUT2 output could not set to 0 in C(C). R(R), P(P) or Q(Q) output mode.

Output

mode

Input mode Operation

Up, Up-1, 2 Down, Down-1, 2 Up/Down A, B, C

(F)

※After count-up, counting display

value increases or decreases until

reset signal is applied and retained

output is maintained.

(N)

※After count- up, counting display

value and retained output are main-

tained until reset signal is applied.

(C)

※

When count-up, counting display value

will be reset and count simultaneously.

※OUT1 retained output will be off after

OUT2 one- shot time.

※

The one-shot output time of OUT1

one-shot output time is operated

gardless of OUT2 output.

(R)

※After OUT2 one-shot time,

counting

display value will be reset

and count

simultaneously.

※OUT1 retained output will be off after

OUT2 one-shot time.

※

OUT1 one-shot output time is operated

regardless of OUT2 output.

(K)

※After count-up, counting display

value increases or decreases until

RESET input is applied.

※OUT1 retained output is off after

OUT2 one-shot time.

※OUT1 one-shot output time is

operated

regardless of OUT2 output

(P)

※

After count-up, counting display value

maintained while OUT2 output is on.

Counting value is internally reset and

counts simultaneously.

※When OUT2 output is off, displays

counting value while OUT2 is ON,

and it increases or decreases.

※OUT1 retained output is off after

OUT2 one-shot time.

※OUT1 one-shot output time is

oper-

ated regardless of OUT2 output.

(Q)

※After count-up, counting display

value increases or decreases during

OUT2 one-shot time.

※OUT1 retained output is off after

OUT2 one-shot time.

※

OUT1 one-shot output time is operated

regardless of OUT2

output.

(A)

※

After count-up, counting display value

and OUT1 retained output are main-

tained until RESET input is applied.

※OUT1 one-shot output time is oper-

ated regardless of OUT2 output.

One-shot output(0.01 to 99.99 sec.) One-shot output Retained output

Retained output

J-22

CT Series

Indicate

mode

(DSpM)

Count chart

Operation

In case of input mode is Up

(Up, Up-1, Up-2)

In case of input mode is Down

(Down, Down-1, Down-2)

TOTAL

(TOTAL)

Count value increases or decreases

until RESET input is applied.

When reaching max. count value or

min. count value, it will be reset and

count simultaneously.

HOLD

(HOLD)

Count value increases or decreases

until RESET input is applied, count

value indicator ashes when reaching

preset value(Up count) or 0(Down

count).

RESET RESET

PRESET

RESET

999999 999999

999999

PRESET

-99999

※The single preset type output(OUT) is operated as OUT2 of dual preset type.

※The dual preset model OUT1 output is operated as one-shot or retained output.(except S, T, D mode)

※OUT1 output could be set to 0 in all modes and 0 value output turns ON.

※OUT2 output could not set to 0 in C(C), R(R), P(P) or Q(Q) output mode.

※In case of UP/DOWN (UD-A, UD-B, UD-C) input mode, in-

dication mode (DSpM) of the conguration is not displayed.

Output mode Up/Down - A, B, C Operation

(S)

※

OUT1 and OUT2 keeps ON status in

following condition:

Counting display value ≧ PRESET1

Counting display value ≧ PRESET2

(T)

※OUT1 output is off:

Counting display value ≧ PRESET1

※OUT2 keeps ON status in following

condition:

Counting display value ≧ PRESET2

(D)

※When counting display value is equal

to setting value(PRESET1, PRESET2)

only, OUT1 or OUT2 output keeps ON

status.

※When setting 1kcps for counting

speed, solid state contact output

should be used.

RESET

999999

-99999

999999

-99999

PRESET2

PRESET1

OUT1

OUT2

(OUT)

OUT2

(OUT)

OUT2

(OUT)

Output operation mode(Counter)

Counter operation of the indicator(CT6S-I, CT6Y-I, CT6M-I)

Retained output Coincidence

output

● In case of the input mode is Command input (UD-A), Individual input(UD-B), Phase difference input(UD-C).

J-23

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Parameter setting(Timer) ( key: To select setting mode or key: To change setting value)

Setting mode How to set

Counter/Timer

C-T COUN TIME

Timer range

HOUR/MIN/SEC

UP/DOWN mode

U-D UP DN

Indication mode

DSpM

TOTAL HOLD ONtD

Memory protection

DATA CLR REC

Output mode

OUtM

OND ONd1 ONd2 FLK FLk1 FLk2 INT

INTG NFd1 NFD OFD INt2 INt1

OUT2 output time

OUT2

key: To shift ashing digit position of OUT2 output time value.

key: To change OUT2 output time value.

※

Set OUT2 one-shot output time.

※

Setting range: 0.01 to 99.99sec.

※

HOLD is displayed by pressing key 4 times.

OUT1 output time

OUT1

key: To shift ashing digit position of OUT1 output time value.

key: To change OUT1 output time value.

※Set OUT1 one-shot output time.

※Setting range: 0.01 to 99.99sec., Hold

※HOLD is displayed by pressing key 4 times.

Input logic

S1G

Input signal time

InT 1 20

Lock key

LOCK

LOFF LOc1

LOc3 LOc2

※Used for the indicator only.

※ It is added that the feature which set the setting time when

selecting

HOLD or ONtD (Refer to J-28 page ' Timer

operation for the indicator').

※COUN: COUNTER

TIME: TIMER

0.001s to

999.999s

0.1h to

99999.9h

0.001s to

9.999s

0.01s to

99.99s

1h to

9999h

0.1s to

999.9s

1m to

99h59m

1s to

9999s

1m to

9999s

1s to

99m59s

0.1m to

999.9m

0.01s to

9999.99s

1m to

9999h59m

0.1s to

99999.9s

1s to

99h59m59s

1s to

999999s

1m to

999999m

0.01s to

99m59.99s

0.1m to

99999.9m

0.1s to

999m59.9s

1s to

9999m59s

6digit type

4digit type

SEC

99(999

SEC

999(99

M S

995(99

SEC

9999(9

SEC

999999

HOUR

9999(9

H M

999959

H M 5

995959

MIN

999999

MIN

9999(9

M 5

999959

M S

9995(9

SEC

9959

SEC

(999

MIN

99(9

MIN

9999

H M

9959

HOUR

9999

SEC

9(99

SEC

99(9

SEC

9999

※Used for the indicator only.

※ㅑCLR : Initializes time value when power is off.

REC : Memorizes time value at the moment of power off.

※UP: Time proceeds from 0 to the setting value.

※DN: Time proceeds from the setting value to 0.

※NPN: No-Voltage input

※PNP: Voltage input

※CTS/CTY: Set min. external INA, INH, RESET signal width.

※CTM: Set min. external INA, RESET, INHIBIT,

BATCH RESET signal width.

※LOFF: Cancellation of the lock mode

LOc1: Locks key.

LOc2: Locks , , keys.

LOc3 : Locks , , , keys.

※Check input logic value(PNP, NPN).

[unit: ms]

J-24

CT Series

Output operation mode(Timer)

One-shot output

One-shot output Retained output

Retained output

Output mode Input mode Operation

OND

(OND)

Signal On Delay(Power Reset)

1) Time starts when INA signal turns on.

2) When INA signal turns off, time resets.

3) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

4) Control output operates as retained

or one-shot output.

ONd1

(OND.1)

Signal On Delay 1(Power Reset)

1) Time starts when INA signal turns on,

if INA signal is applied repeatedly,

only initial signal is recognized.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) Control output operates as retained

or one-shot output.

4) Only rst INA input signal is valid in

case INA input signal is repeatedly

applied.

ONd2

(OND.2)

Power On Delay(Power Hold) 1) Time starts when power turns on.

(There is no INA function.)

2) Time resets when reset turns on.

Time starts when reset turns off.

3) Control output operates as retained

or one-shot output.

4) It memorizes display value at the

moment of power off.

FLK

(FLK)

Flicker(Power Reset) 1)

Time starts when INA signal turns on.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) Control output operates as retained

output, output turns off for the T.off

time and turns off for the T.off time

and turns on for the T.on time repeat-

edly.

Ta+Tb = T.off setting time

4) The T.on time and T.off time must be

set individually.

5) In case of using the contact output, min.

setting time must be set over 100ms.

RESET

Setting time2

Setting time1

POWER

INA(START)

INH(INHIBIT)

Setting time1

Display

Down

Display

Down

Display

Down

Display

Down

OUT1

OUT2

RESET

Setting time2

Setting time1

POWER

INA(START)

INH(INHIBIT)

Setting time1

OUT1

OUT2

RESET

Setting time2

Setting time1

POWER

INA(START)

INH(INHIBIT)

Setting time1

OUT1

OUT2

RESET

POWER

INA(START)

INH(INHIBIT)

setting time

T.on

T.off

t a t-a

T.off T.offT.offT.on

T.on T.onT.on

Ta Tb

T.off

OUT2(OUT)

T1: Setting time1

T2: Setting time2

INA

OUT1

OUT2

(OUT)

T1: Setting time1

T2: Setting time2

INA

OUT1

OUT2

(OUT)

T.off T.offT.on

POWER

INA

OUT2

(OUT)

T1: Setting time1

T2: Setting time2

OUT1

POWER

HOLD

OUT2

(OUT)

※Power Reset: There is no memory protection.(Initializes the display value when power is off)

Power Hold: There is memory protection.(Memorizes the display value at the moment of power off, indicates the memorized

display value when power is resupplied.)

J-25

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Output mode Input mode Operation

FLk1

(FLK.1)

Flicker 1(Power Reset)

1) Time starts when INA signal turns on.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) Control output operates as retained

output.

4) In case of using the contact output, min.

setting time must be set over 00ms.

1) Time starts when INA signal turns on.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) Control output operates as one-shot

output.

In case of using the contact output,

min. setting time must be set over

100ms.

FLk2

(FLK.2)

Flicker 2(Power Hold)

1) Time starts when INA signal turns ON and

the display value at the moment when

power is off is memorized.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) Control output operates as retained output.

4) Control output will be reversed when it

reaches to setting time.(At the initial

start, OUT2 control output is OFF).

5) In case of using the contact output, min.

setting time must be set over 100ms.

1) Time starts when INA signal turns ON and

the display value at the moment when

power is off is memorized.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) Control output operates as one-shot

output.

4) In case of using the contact output, min.

setting time must be set over 100ms.

Output operation mode(Timer)

RESET

Setting time

POWER

Hold output

One-Shot output

INA(START)

INH(INHIBIT)

Display

Down

Display

Down

Display

Down

Display

Down

OUT2(OUT)

t t t ta t-a

t t t

※Power Reset: There is no memory protection.(Initializes the display value when power is off)

Power Hold: There is memory protection.(Memorizes the display value at the moment of power off, indicates the memorized

display value when power is resupplied.)

Retained output

Retained outputOne-shot output One-shot output

T:Setting time

POWER

Hold

T-c c T

INA

OUT2

(OUT)

T:Setting time

POWER

Hold

T-c c T

INA

OUT2

(OUT)

T:Setting time

POWER

T T T

INA

OUT2

(OUT)

T:Setting time

POWER

T T T

INA

OUT2

(OUT)

J-26

CT Series

Output mode Input mode

Operation

ㅑㅑINT

(INT)

Interval (Power Reset)

1) Control output turns ON and time starts

when INA signal turns ON.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) When it reaches setting time, indication

value and control output are reset

automatically.

4) Control output is ON when time is

progressing.

INt1

(INT.1)

Interval 1(Power Reset)

1) Control output turns ON and time starts

when INA signal turns ON.

2) When INA signal is on:

Power ON Time Start is operated

Power OFF Time Start is operated

3) When it reaches setting time, indication

value and control output are reset

automatically.

4) Control output is ON when time is

progressing.

5) INA input is ignored while time is

progressing.

INt2

(INT.2)

Interval 2(Power Reset)

1) Time starts when INA input is ON and

resets when INA input is OFF.

2) INA input is ON, OUT1 output is ON during

T1 or t1.

3) When it reaches setting time1, display

value resets and OUT2 output is ON

during T2 or t2 output time.

※

Output turns OFF when reaching the

setting time even if one-shot time

is longer than setting time.

Output operation mode(Timer)

RESET

Setting time

Setting time1

Setting time2

Setting time

POWER

INA(START)

INH(INHIBIT)

Display

Down

Display

Down

Display

Down

OUT2(OUT)

OUT2

OUT1

※Power Reset: There is no memory protection.(Initializes the display value when power is off)

Power Hold: There is memory protection.(Memorizes the display value at the moment of power off, indicates the memorized

display value when power is resupplied.)

Retained output

Retained outputOne-shot output One-shot output

T:Setting time

POWER

T T

INA

OUT2

(OUT)

T:Setting time

POWER

INA

OUT2

(OUT)

INA

OUT1

OUT2

T1: Setting time1

T2: Setting time2

t1: One-shot1

t2: One-shot2

(Single preset model has no INT.2 mode)

J-27

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Output mode Input mode Operation

OFD

(OFD)

Signal Off Delay1(Power Reset)

1) If INA is ON, control output remains

ON. (except when power is off and

reset is on)

2) When INA signal is OFF, time pro-

cesses.

3) When it reaches setting time, indi-

cation value and control output are

reset automatically.

NFD

(NFD)

On-Off Delay (Power Reset) 1) When INA input is ON, output is

ON and time is progressing, then

output is OFF after On_Delay time.

2) When INA input is OFF, output is

ON and time is progressing, then

output is OFF after Off_Delay time.

3) If INA input is OFF within On_Delay

time, step 2 starts again.

4) If INA input is ON within Off_Delay

time, step 1 starts again.

NFd1

(NFD.1)

On-Off Delay1 (Power Hold) 1) When INA input turns ON, time

progresses and output turns ON

after On_Delay time.

2) When INA input turns OFF, time

progresses and output turns OFF

after Off_Delay time.

3) If INA input turns OFF within On_

Delay time, output will turn ON and

step2 operate.

4) If INA input turns ON within Off_

Delay time, output will turn OFF

and step1 operate.

INTG

(INTG)

Integration Time(Power Reset)

1) Time is progressing while INA input

is ON.

2) Time progress stops while INA input is

OFF.

3) When it reaches the setting time,

output is ON.

※

Power Reset: There is no memory protection.(Initializes the display value and the output status when re-supplying the power.)

Power Hold: There is memory protection.(It memorizes the status of power off. When re-supplying the power, it returns

the memorized display value and the output status.)

RESET

Setting time

On_Delay

Off_Delay

Setting time

POWER

INA(START)

INH(INHIBIT)

Display

Down

Display

Down

Display

Down

Display

Down

Display

Down

OUT2(OUT)

Output operation mode(Timer)

POWER

INA

OUT2

(OUT) T: Setting time

INA

OUT2

(OUT) T1: On_Delay

T2: Off_Delay

T1 T2

INA

OUT2

(OUT) T1: On_Delay

T2: Off_Delay

T1 T2

Retained output

Retained outputOne-shot output One-shot output

J-28

CT Series

TOTAL

(TOTAL)

1) Time starts when INA input is ON.

2) Setting value is initialized when Reset input

is ON.

3) Time progress stops when INHIBIT input is

ON.

4) Resets when power is OFF.

1) Time starts when INA input is ON.

2) Setting value is initialized when Reset input

is ON.

3) Time progress stops while INHIBIT input

is ON.

4) Display value at the moment of power OFF

is memorized.

HOLD

(HOLD)

1) Time progresses when INA input is ON.

2) Time progress stops while INA input is OFF.

3) When time reaches setting time, display

value will stop and ash.

4) When reset input is applied, display value

is initialized.

5) Resets when power is OFF.

1) Time progresses when INA input is ON.

2) Time progress stops while INA input is OFF.

3) When time reaches setting time, display

value will stop and ash.

4) When reset input is applied, display value

is initialized.

5) Display value the moment when power is

OFF is memorized.

ONtD

(On Time

Display)

※ON time indicate mode of INA input

1) Time reset start operates when INA input

turns ON.

2) Time progress stops while INA input is OFF.

3) When time progress stops and power is

off, the display value is initialized.

4) If progress time is greater than setting

time when INA input turns off, display

value ashes and operation stops until

reset signal is applied.

※ON time indicate mode of INA input

1) Time reset start operates when INA input

turns ON.

2) Time progress stops while INA input is OFF.

3) When time progress stops and power is

off, the display value is memorized.

4) If progress time is greater than setting

time when INA input turns off, display

value ashes and operation stops until

reset signal is applied.

When memory protection setting is OFF

When memory protection setting is ON

RESET

Max.

time range

Max.

time range

POWER

INA(START)

INH(INHIBIT)

Display

Down

RESET

Setting time

POWER

INA(START)

INH(INHIBIT)

Display

Down

RESET

Max.

time range

Max.

time range

POWER

INA(START)

INH(INHIBIT)

Display

Down

Timer operation of the indicator(CT6S-I, CT6Y-I, CT6M-I)

J-29

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Timer '0' time setting

Available output operation mode to set '0' time setting

OND, ONd1, ONd2, NFD, NFd1

Operation according to output mode(at 0 time setting)

Setting value1(PS1) is higher than Setting value2(PS2)

1) OND(Signal ON Delay) mode [OND]

2) OND.1(Signal ON Delay 1) mode [ONd1]

3) OND.2(Power ON Delay2) mode [ONd2]

4) NFD(ON-OFF Delay) mode [NFD]

5) NFD.1(ON-OFF Delay1) mode [NFd1]

● Setting time1 is set to 0

● OFF_Delay setting time is set to 0

● Setting time2 is set to 0

● ON_Delay setting time is set to 0

OND(OND), OND.1(ONd1)or OND.2(ONd2)output mode

● UP mode: When the timer setting value1 is greater than the setting value 2, OUT1 output does not turn ON.

● DOWN mode: When the timer setting value1 is greater than the setting value 2, OUT1 output does not turn ON.

If the setting value 1 is same as the setting value2 and START signal is applied, OUT1 output turns ON

immediately.

Setting time2

OUT1

OUT2

INA(START)

UP mode DOWN mode

RESET

Setting time2

OUT1

OUT2

INA(START)

UP mode DOWN mode

RESET

Setting time1

OUT1

OUT2

INA(START)

RESET

Setting time1

OUT1

OUT2

POWER

UP mode

RESET

On_Delay

OUT2

(OUT)

INA(START)

Display

Down

RESET

Off_Delay

OUT2

(OUT)

INA(START)

Display

Down

RESET

On_Delay

OUT2

(OUT)

INA(START)

Display

Down

RESET

Off_Delay

OUT2

(OUT)

INA(START)

Display

Down

RESET

OUT1

OUT2

POWER

UP mode DOWN mode

Setting time 1

OUT1

OUT2

INA(START)

Setting time 2

J-30

CT Series

Communication mode

Parameter setting

Application of system organization

Communication control ordering

( key: To select setting mode, or key: To change setting value)

Address code

CT Series

Upper system

※A → Min. 1sec. after applying power

B → 38400bps: Approx. 1ms.

19200bps: Approx. 2ms.

9600bps: Approx. 4ms.

4800bps: Approx. 8ms.

2400bps: Approx. 16ms.

C → Min. 20ms

A CB

Address code

Command

Data

CRC16

1. The communication method is Modbus RTU(PI-MBUS-300-REV.J).

2. After 1sec. of power supply into the high order system, it starts to communicate.

3. Initial communication will be started by the high order system. When a command comes out from the high order system,

CT Series will respond.

※It is recommended to use communication converter, RS485 to Serial converter(SCM-38I, sold separately), USB to

RS485 converter(SCM-US48I, sold separately). Please use a proper twist pair for RS485 communication.

Computer

GND

V(12-24VDC)

RS232C Cable

RxD - RxD

TxD - TxD

GND - GND

Terminating

resistance

RS232C

B(-)

A(+)

A(+) B(-) A(+) B(-) A(+) B(-)

B(1)

A(+)

CT Series

#01

CT Series

#02

CT Series

#30

CT Series

#31

OFF

A(+)

RS485

Setting mode How to set

Com. address

(ADDR)

: To shift ashing digits of Com. address.

: To change the ashing digits.

Com. speed

(BPS)24 48 96 192 384

Com. parity

(PRTY)

NONE EVEN ODD

Com. stop bit

(STP)1 2

esponse

waiting time

(RSwT)

Com. write

(COmW)

ENA DISA

※Setting range according to com. speed.

2400bps 16ms to 99ms

4800bps 8ms to 99ms

9600bps 5ms to 99ms

19200bps 5ms to 99ms

38400bps 5ms to 99ms

※Setting range of com. address: 1 to 127

※If the same address is applied during multicom.,

it will not work correctly.

※ENA : Permits com. write(Enable)

DISA : Prohibits com. write(Disable)

※2400/4800/9600/19200/38400bps

※NONE: None EVEN : Even number ODD: Odd number

: To shift ashing digits position of com.

response waiting time.

: To change the ashing digits position

value.

J-31

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Communication command and block

1) Read Coil Status(Func 01 H),

Read Input Status(Func 02 H

2) Read Holding Registers(Func 03 H),

Read Input Registers(Func 04 H)

3) Force Single Coil(Func 05 H)

4) Preset Single Register(Func 06 H)

The format of query and response

Read Coil Status(Func 01 H)

Master reads OUT2 00002(0001H) to 00003(0002H),

OUT1 output status(ON : 1, OFF : 0) from the

Slave(Address 01).

On slave side OUT2 00003(0002H) : OFF,

OUT1 00002(0001H) : ON

Read Input Register (Func 04 H)Master reads preset value

21004(03EBH) to 21005(03ECH) of counter/timer, Slave

(Address 15).

In case that the present value is 123456(0001 E240 H) in

slave side, 31004(03EBH): E240 H, 31005(03ECH): 0001H

● Query(Master)

● Response(Slave)

CRC 16

Slave

Address

Function

Starting

Address No. of Points Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Starting

Address No. of Points Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Coil Address Force Data

Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Address Preset Data

Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Coil Address Force Data

Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Address Preset Data

Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Byte

Count Data Data Data

Error Check

(CRC 16)

Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address

Function

Byte

Count

Data Data Data Error Check

(CRC 16)

High Low High Low High Low Low High

1Byte 1Byte 1Byte

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

5) Preset Multiple Registers(Func 10 H)

6) Application

● Query(Master)

● Response(Slave)

Slave

Address Function

Starting

Address

No. of

Byte

Count

Data Data

Error

Check

(CRC 16)

High Low High Low High Low High Low Low High

1Byte 1Byte

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address Function

Starting Address No. of Register Error Check

(CRC 16)

High Low High Low Low High

1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte

Slave

Address Function

Byte

Count

Data Data Error Check

(CRC 16)

High Low High Low Low High

0F H 04 H 04 H E2 H 40 H 00 H 01 H E2 H 28 H

Slave

Address Function Starting Address No. of Points Error Check

(CRC 16)

High Low High Low Low High

0F H 04 H 03 H EB H 00 H 02 H 00 H 95 H

Slave

Address Function Starting Address No. of Points Error Check

(CRC 16)

High Low High Low Low High

01 H 01 H 00 H 01 H 00 H 02 H EC H 0B H

Slave

Address Function Byte Count

Data

(00003 to

00001)

Error Check

(CRC 16)

Low High

01 H 01 H 01 H 02 H D0 H 49 H

CRC 16

J-32

CT Series

Modbus Mapping Table

1) Reset/Output

2) Terminal input status

3) Product Information

4) Monitoring data

5) Preset value setting group

● Date format of 31001(03E8) address bit

No(Address) Func Explanation

Setting range

Notice

00001(0000)

01/05

Reset

0:OFF 1:ON

00002(0001)

OUT2 output

0:OFF 1:ON

00003(0002)

OUT1 output

0:OFF 1:ON

00004(0003)

01 BATCH output

0:OFF 1:ON

For BATCH

output model

00005(0004)

01/05 BATCH resets

0:OFF 1:ON

For BATCH

output model

No(Address) Func

Explanation Setting range Notice

31001

(03E8) 04

BA.O LED

display status

0:OFF 1:ON Bit 5

OUT2 LED

display status

0:OFF 1:ON Bit 6

OUT1 LED

display status

0:OFF 1:ON Bit 7

BA.S LED

display status

0:OFF 1:ON Bit 10

LOCK LED

display status

0:OFF 1:ON Bit 11

PS2 LED

display status

0:OFF 1:ON Bit 12

PS1 LED

display status

0:OFF 1:ON Bit 13

TMR LED

display status

0:OFF 1:ON Bit 14

CNT LED

display status

0:OFF 1:ON Bit 15

31002(03E9)

Present value

of BATCH

counter

0 to 999999

For BATCH

output

model

31003(03EA)

31004(03EB)

Present value

counter/timer

Counter

6digit type: -99999 to

999999

4digit type: -999 to 9999

Timer: Within time setting

range

Use counter

and timer

in common

31005(03EC)

31006(03ED)

Display unit

Counter: decimal point

of display value

Timer: Time range

Counter:

40058 Data

Timer:

40102 Data

31007(03EE)

PS(2)

setting value

Counter

6digit type: -99999 to

999999

4digit type: -999 to 9999

Timer: Within time setting

range

Use counter

and timer

in common

31008(03EF)

31009(03F0)

PS1

setting value

Counter

6digit type: -99999 to

999999

4digit type: -999 to 9999

Timer: Within time setting

range

Use counter

and timer

in common

31010(03F1)

31011(03F2)

Setting value

of BATCH

counter

0 to 999999

Use counter

and timer

in common

31012(03F3)

31013(03F4)

Checking the

input logic 0: NPN, 1 : PNP

No(Address)

Func Explanation

Setting range

Notice

10001(0000) 02 INA input status 0:OFF 1:ON

Terminal input

status

10002(0001) 02 INB input status 0:OFF 1:ON

Terminal input

status

10003(0002) 02 INHIBIT input status 0:OFF 1:ON

Terminal input

status

10004(0003) 02 RESET input status 0:OFF 1:ON

Terminal input

status

10005(0004) 02

BATCH RESET

input status

0:OFF 1:ON

Terminal input

status

No(Address)

Func Explanation Setting range Notice

40001(0000)

PS2 setting value

PS setting value

Counter

6digit type: 0 to

999999

4digit type: 0 to 9999

Timer: Within time

setting range

Use counter

and timer

in common

40002(0001)

40003(0002)

PS1 setting

value

Use counter

and timer

in common

40004(0002)

40005(0004)

BATCH coun-

ter

setting value

0 to 999999

Use counter

and timer

in common

40006(0005)

Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit4 Bit 3 Bit 2 Bit 1 Bit 0

CNT TMR PS1 PS2

LOCK

BA.S

- -

OUT1 OUT2

BA.O

-----

0 or 1 0 or 1 0 or 1 0 or 1 0 or 1 0 or 1 0 0 0 or 1 0 or 1 0 or 1 0 0 0 0 0

No(Address)

Func

Explanation Notice

30001~30100

04 Reserved

30101(0064)

04 Product number H Model ID

30102(0065)

04 Product number L

30103(0066)

04 Hardware version

30104(0067)

04 Software version

30105(0068)

04 Model no. 1 "CT"

30106(0069)

04 Model no. 2 "6M"

30107(006A)

04 Model no. 3 "-2"

30108(006B)

04 Model no. 4 "PT"

30109(006C)

04 Reserved

30110(006D)

04 Reserved

30111(006E) 04 Reserved

30112(006F) 04 Reserved

30113(0070) 04 Reserved

30114(0071) 04 Reserved

30115(0072) 04 Reserved

30116(0073) 04 Reserved

30117(0074) 04 Reserved

30118(0075) 04 Coil Status

Start Address 0000

30119(0076) 04 Coil Status

Quantity

30120(0077)

04 Input Status

Start Address 0000

30121(0078)

04 Input Status Quantity

30122(0079)

04 Holding Register

Start Address 0000

30123(007A)

04 Holding Register

Quantity

30124(007B)

04 Input Register

Start Address 0064

30125(007C)

04 Input Register Quantity

※

2 Words data format: Upper data has high number address.

Ex)31004 : Present Value(Low Word),

31005 : Present Value(High Word)

J-33

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

6) Function setting mode (Counter group)

7) Function setting mode (Timer group)

No(Address) Func Explanation Setting range Notice

40051(0032) 03/06/16 Counter/Timer

(C-T)

COUN

TIME

Use counter and timer in common

40052(0033) 03/06/16 Input mode(IN)

UP-1

2: UP-2

DN-1

DN-2

UD-A

UD-B

UD-C

40053(0034) 03/06/16 Indication mode(DISM)0:

TOTAL

HOLD

For the indicator

40054(0035) 03/06/16 Output mode(OUTM)

10:

40055(0036) 03/06/16 Maximum counting

speed(CPS)

10K

40056(0037) 03/06/16 OUT2(OUT) output time

0001

9999

unit: ×10㎳

40057(0038) 03/06/16 OUT1 Output time

0001

9999

unit: ×10㎳

40058(0039) 03/06/16 Decimal point(DP)0:

------

----.--

--.----

-----.-

---.---

-.-----

4digit type 0: ----

1: ---.- 2: --.-- 3: -.---

40059(003A) 03/06/16 Min. reset time

(RST)

unit: ms

40060(003B) 03/06/16 Prescale decimal

point position(SClD)

-----.-

---.---

-.-----

----.--

--.----

4digit type

1: ---.- 2: --.-- 3: -.---

40061(003C) 03/06/16 Prescale value(SCL)6digit type:

)00001

999999

4digit type:

)001

9999

Connected with prescale

decimal point position

40062(003D)

40063(003E) 03/06/16 Start value(STRT)6digit type:

000000

999999

4digit type:

0000

9999

Connected with decimal

point position of display value

40064(003F)

40065(0040) 03/06/16

Memory protection

(DATA)0: CLR 1: REC Use counter and timer

in common

40066(0041) 03/06/16 Lock key(LOCK)0: lOFF 1: LOc1 2: LOc2 3: LOc3

No(Address) Func Explanation Setting range Notice

40101(0064) 03/06/16 Counter/Timer

(C-T)

COUN

TIME

Use counter and timer

in common

40102(0065) 03/06/16 Time range

(

HOUR

MIN

SEC

)

4digit type

0: 0.001s to 9.999s

1: 0.01s to 99.99s

2: 0.1s to 999.9s

3: 1s to 9999s

4: 1s to 99m59s

5: 0.1m to 999.9m

6: 1m to 9999m

7: 1m to 99h59m

8: 1h to 9999h

6digit type

0: 0.001s to 999.999s

1: 0.01s to 9999.99s

2: 0.1s to 99999.9s

3: 1s to 999999s

4: 0.01s to 99m59.99s

5: 0.1s to 999m59.9s

6: 1s to 9999m59s

7: 1m to 99999.9m

8: 1m to 999999m

9: 1s to 99h59m59s

10: 1m to 9999h59m

11: 0.1h to 99999.9h

40103(0066) 03/06/16 UP/Down mode

(

U-D

)0:

40104(0067) 03/06/16 Output mode

(

OUTM

)

OND

ONd1

ONd2

FLK

FLk1

FLk2

INt1

INt2

OFD

10:

NFD

11:

NFd1

12:

INtG

40105(0068) 03/06/16

OUT2(OUT) Output time

(

OUT2

)

0000

9999

(0: Hold) unit: ×10ms

40106(0069) 03/06/16 OUT1 Output time

(

OUT1

)

0000

9999

(0 : Hold) unit: ×10,ms

40107(006A) 03/06/16 Input signal time(

INT

)0:

unit: ms

40108(006B) 03/06/16

Memory protection

(

DATA

)0:

CLR

REC

Use counter and timer in common

40109(006C) 03/06/16 Lock key(

LOCK

)0:

lOFF

LOc1

LOc2

LOc3

Use counter and timer in common

40110(006D) 03/06/16 ndication mode(

DSpM

)0:

TOTAL

HOLD

ONtD

For the indicator

J-34

CT Series

8) Function setting mode (Communication group)

Exception processing

Read of the parameter area

00002(OUT2), 00003(OUT1), 00004(BA, 0), 10001 to 10005(Terminal input), 30101 to 30125(Product information),

31001 to 31013(Monitoring data)

Read and write of the parameter area

00001(Reset starts), 00005(BATCH Reset starts), 40001 to 40006(Setting value saving group),

40051 to 40066(Counter setting group), 40101 to 40110(Timer setting group),

40151 to 40156(Communication setting group)

Read of communication

Read parameter value using communication.(Function : 01H, 02H, 03H, 04H)

It is able to read communication regardless of permitting/prohibiting communication writing.

Communication write

Change parameter value using communication.(Function: 05H, 06H, 10H)

● When change the parameter setting value of ' Function setting mode Counter group' or ' Function setting mode

Timer group' using communication, reset indication will ash in 3 sec. and display value will be reset.(Counting display

value and progress time before changing parameter setting value are not saved.)

● When change the parameter setting value of ' Preset value setting group' or ' Function setting mode Communica-

tion group' using communication, counting display value or progress time will not be reset.

● In prohibit writing communication setting ( = 1: ), a write command does not process.

● If set value beyond the setting range, this setting value is substituted for the value within the setting range and then

memorized.

When communication error occurs, the highest bit of received function is set

to 1, then sends response command and transmits exception code.

● Illeegal Function(Exception Code: 01H): Not supporting command

● Illegal Data Address(Exception Code: 02H): Mismatch between the number of asked data and the number of transmit-

table data.

● Illegal Data Value(Exception Code: 03H): Mismatch between asked the number of data and transmittable the number of

data in device

● Slave Device Failure(Exception Code: 04H): Command is processed incorrectly.

Example)

Master reads output status (ON:1, OFF:0) of non existing coil 01001 (03E8 H) from Slave (Address17).

No(Address) Func Explanation Setting range Notice

40151(0096) 03/06/16 Com. address (

ADDR

) 1 to 127

40152(0097) 03/06/16 Com. speed (

BPS

) 0:

192

384

unit: ×100bps

40153(0098) 03/06/16 Com. parity (

PRTY

) 0:

NONE

EVEN

ODD

40154(0099) 03/06/16 Stop bit (

STP

) 0:

40155(009A) 03/06/16

Response waiting time (

RSwT

)

05 to 99 unit: ms

40156(009B) 03/06/16 Com. writing (

COmW

) 0:

ENA

DISA

Slave Address Function+80H Exception Code Error Check(CRC16)

Low High

1Byte 1Byte 1Byte 1Byte 1Byte

Slave Address Function Starting Address No. of Points Error Check(CRC16)

High Low High Low Low High

11H 01H 03H E8H 00H 01H ##H ##H

Slave Address Function + 80H Exception Code Error Check(CRC16)

Low High

11H 81H 02H ##H ##H

Read and write of parameter value using communication

● Response(Slave)

● Query(Master)

J-35

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Programmable Counter/Timer

Input signal line

● Use as short a cable from the sensor to this unit as possible.

● Use shielded cable for long input line.

● Wire as separating input line from the power line.

When selecting input logic

Be sure that supply power is off when selecting input logic,

then select logic input according to input logic changing

method.

Contact count input (When it is used as Counter)

If apply contact input at high speed mode(1k, 5k, 10k), it

may cause miscount by chattering.

Therefore set low speed mode(1cps or 30cps) at contact input.

When test dielectric voltage and insula-

tion

resistance of the control panel with this

unit

installed.

● Please isolate this unit from the circuit of control panel.

● Please make all terminals of this unit short-circuited.

Do not use below places.

● Place where there are severe vibration or impact.

● Place where strong alkalis or acids are used.

● Place where there are direct ray of the sun.

● Place where strong magnetic eld or electric noise are

generated.

Installation environment

● It shall be used indoor.

● Altitude Max. 2000m

● Pollution Degree 2

● Installation Category II

Proper usage

Power ON

OFF 100㎳500㎳

The unstable time

against the input signal.

The power ON/OFF

Power voltage rises for 100ms after power on and falls for

500ms after power off. Therefore be sure to apply input

signal after 100ms and power turns on again after 500ms

when power turns off.

● Be sure to use insulated and resistive voltage /current

Class2 supply power device to input 24VAC/24-48VDC

power supply model.