Microwave Ceramics and Modules Filter
2 – Pole Filter for Mobile Broadcasting B69812N2647A327
Preliminary Data Sheet
ISSUE DATE 02.03.04 ISSUE P5 PUBLISHER SAW MWC PD PAGE 1/5
Features
Small Dimensions (3mm x 2.8mm x 2mm)
Low Losses in Passband (typ. 1.5dB)
High attenuations at GSM, PDC, PHS, UMTS, and WLAN Bands
Excellent reflow solderability, no migration effect due to copper/tin metallization
Index
Page 2 Dimension Limits
Recommended Footprint
Page 3 Characteristics
Maximum ratings
Typical passband characteristic
Page 4 Processing information
Soldering requirements
Page 5 Delivery mode
Microwave Ceramics and Modules Filter
2 – Pole Filter for Mobile Broadcasting B69812N2647A327
Preliminary Data Sheet
ISSUE DATE 02.03.04 ISSUE P5 PUBLISHER SAW MWC PD PAGE 2/5
Dimension Limits
Recommended Footprint
Solder Pads:
I/O Pads must be
connected to lines with
50 impedance.
In the application a
termination of 50
must be realized.
Ground, covered with
solder resist, connected
to lower ground plane
by vias with maximum
diameter of 0.3mm and
max. distance of 1mm
I/O
G
G
G
I/O
Microwave Ceramics and Modules Filter
2 – Pole Filter for Mobile Broadcasting B69812N2647A327
Preliminary Data Sheet
ISSUE DATE 02.03.04 ISSUE P5 PUBLISHER SAW MWC PD PAGE 3/5
Characteristics (over whole temperature range) min. typ. max.
Center frequency fc- 2.6425 - GHz
Insertion loss αIL 1.5 2.0 dB
Passband (2629- 2656) B27 MHz
Amplitude ripple (peak - peak) ∆α 0.1 0.3 dB
Standing Wave Ratio / Return Loss [dB] 1.5 / -14 2.0 / -9.5
Impedance Z50
Attenuation α
at DC to 440 MHz
at 440 to 1525 MHz
at 1525 to 1680 MHz
at 1680 to 1980 MHz
at 1980 to 2170 MHz
at 2170 to 2500 MHz
at 3450 MHz
57
32
40
35
32
22
30
>70
45
45
40
35
25
35
dB
dB
dB
dB
dB
dB
dB
Maximum ratings
IEC climatic category (IEC 68-1) - 40 /+ 90/56
Operating temperature Top - 40 / + 85 °C
Typical passband characteristics
-60
-50
-40
-30
-20
-10
0
2400 2500 2600 2700 2800 2900 3000
frequency [MHz]
attenuation [dB]
S11
S21
Microwave Ceramics and Modules Filter
2 – Pole Filter for Mobile Broadcasting B69812N2647A327
Preliminary Data Sheet
ISSUE DATE 02.03.04 ISSUE P5 PUBLISHER SAW MWC PD PAGE 4/5
Processing information
Wettability acc.to IEC 68-2-58: 75% (after aging)
Soldering Requirements
Profile for eutectic
SnPb solder paste
Profile for leadfree
solder paste
Soldering type reflow reflow
Maximum solderin
g
tem
p
erature 235
(
max. 2 sec.
)
260
(
max. 2 sec.
)
°C
(measuring point on top surface of the component) 225 (max. 10 sec.) 250 (max. 10 sec.) °C
Recommended soldering conditions (infrared):
20-40 sec.
40-80 sec.
within 10 sec.
Time [sec.]
Temp. [°C]
215°C±10°C
30 sec.
2-3 min.
within 10 sec.
Time [sec.]
Temp. [°C]
245°C±5°C
2.5 °C/s > - 5 °C/s
Microwave Ceramics and Modules Filter
2 – Pole Filter for Mobile Broadcasting B69812N2647A327
Preliminary Data Sheet
ISSUE DATE 02.03.04 ISSUE P5 PUBLISHER SAW MWC PD PAGE 5/5
Delivery mode
Blister tape acc. to IEC 286-3, grey
Pieces/tape: 4000
EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry
r
eco
mm
e
n
ded
by
t
h
e
ZVEI
(Ge
rm
a
n El
ect
ri
ca
l
a
n
d
El
ect
r
o
ni
c
M
a
n
u
f
actu
r
e
r
s
' A
ssoc
i
at
i
o
n
),
u
nl
ess
ot
h
e
rwi
se
ag
r
eed
.
W1 = 13 mm
W2 = 17 mm
W3 = 23 mm
N = 62 mm