sitop
Siemens AG
Automation and Drives
Systems Engineering
Sales Power Supplies, System Cables
www.siemens.com Order No.: E86060-K2410-A101-A5-7600
Power supplies
SITOP power
LOGO!Power
Catalog KT 10.1 2004SITOP Power supplies
Catalog KT 10.1 2004
The information provided in this catalog contains descriptions or
characteristics of performance which in case of actual use do not
always apply as described or which may change as a result of
further development of the products. An obligation to provide
the respective characteristics shall only exist if expressly agreed
in terms of contract. Availability and technical specifications
are subject to change without notice.
1) Available in German only.
System Cabling
SIMATIC TOP connect
Order No.:
E86060-K2410-A201-A3-7600
KT 10.2
Stromversorgungen
SITOP power, LOGO!Power,
SIDAC-S 1)
Order No.:
E86060-K2802-A101-A1
PD 20
Low Voltage
Order No.:
E86060-K1002-A101-A4-7600
LV 10
SIMATIC
Products for
Totally Integrated Automation
and Micro Automation
Order No.:
E86060-K4670-A111-A9-7600
ST 70
Industrial Communication
Order No.:
E86060-K6710-A101-B4-7600
IK PI
SINUMERIK & SIMODRIVE
Automation Systems for
Machine Tools
Order No.:
E86060-K4460-A101-B1-7600
NC 60
PC-based Automation
Order No.:
E86060-K4670-B111-B2-7600
Training for Information
and Industrial Solutions 1)
Order No.:
Paper: E86060-K6850-A101-B3
CD: E86060-D6850-A100-B7-7400
ITC
The offline Mall of
Automation and Drives
Order No.:
CD: E86060-D4001-A110-C3-7600
CA 01
A&D Mall
Internet:
www.siemens.com/automation/mall
Related catalogs
Trademarks
All product designations may be trademarks or product
names of Siemens AG or supplier companies whose use
by third parties for their own purposes could violate the
rights of the owners.
s
Supersedes:
Catalog KT 10.1 · 2002
The products contained in this catalog
also appear in CD-ROM catalog CA 01
Order No.:
E86060-D4001-A110-C3-7600
Please contact your local Siemens
representative.
© Siemens AG 2004
SITOP
Power supplies
SITOP power
LOGO!Power
Catalog KT 10.1 · 2004
The products and sys-
tems described in this
catalog are manufac-
tured/distributed under
application of a certified
quality management
system in accordance
with DIN EN ISO 9001
(Certified Registration
No. 1108). The certifi-
cate is recognized by all
IQNet countries.
Introduction Overview of product families,
Selection guide 1
SITOP power,
Standard 24 V
Single-phase,
Output currents up to 2 A 2
Single-phase,
Output currents 2.5 to 4 A 3
Single-phase and two-phase,
Output current 5 A 4
Single-phase and two-phase,
Output current 10 A 5
Single-phase and two-phase,
Output currents 20 and 40 A 6
Three-phase,
Output currents 5 to 40 A 7
Additional components 8
Uninterruptible power supplies 9
SITOP power Alternative voltages 10
SITOP power AS interface power supplies 11
SITOP power Customized 12
LOGO!Power 13
Technical information
and configuration 14
Dimension drawings 15
Appendix Contact persons
Indexes 16
Welcome to
Automation and Drives
1/2 Siemens KT10.1 · 2004
We would like to welcome you to Automation and
Drives and our comprehensive range of products,
systems, solutions and services for production and
process automation and building technology
worldwide.
With Totally Integrated Automation and Totally
Integrated Power, we deliver solution platforms based
on standards that offer you a considerable savings
potential.
Discover the world of our technology now. If you need
more detailed information, please contact one of your
regional Siemens partners.
They will be glad to assist you.
1/3
Siemens KT10.1 · 2004
Siemens KT10.1 · 2004
1/4
With the launch of Totally Integrated Automation, we were
the first ones on the market to consistently implement the
trend from equipment to an integrated automation solution,
and have continuously improved the system ever since.
Whether your industry is process- and production-oriented or
a hybrid, Totally Integrated Automation is a unique "common
solution" platform that covers all the sectors.
Totally Integrated Automation is an integrated platform for the
entire production line - from receiving to technical processing
Totally Integrated Automation
innovations for more productivity
I
ndustrial
E
thernet
PROCESS FIELD
GAMMA instabus
Building
Technology
ERP
Enterprise
Resource
Planning
MES
Manufacturing
Execution
Systems
Ethernet
Ethernet
Material
Management
Equipment
Management
Production
Order
Management
Production
Operations
Recording
SIMATIC NET
Industrial
Communication
Industrial Wireless
Communication/
MOBIC
ECOFAST IP65
Decentral
Automation System
Micro-Automation
and
Actuator-Sensor
Interface Level
AS-Interface
PROFIBUS
Industrial
Ethernet Safety Integrated
Control SINAUT Telecontrol
System
SIMATIC
Software
SIMATIC
Machine Vision
PC-based Automation
1/5
Siemens KT10.1 · 2004
and production areas to shipping. Thanks to the system-oriented
engineering environment, integrated, open communications
as well as intelligent diagnostics options, your plant now
benefits in every phase of the life cycle.
In fact, to this day we are the only company worldwide that
can offer a control system based on an integrated platform
for both the production and process industry.
Plant
Information
Management
Detailed
Production
Scheduling
SIMATIC IT Framework
Production Modeler
Product Specification
Management System
Laboratory Information
Management System
Field Instru-
mentation/
Analytics
SIMATIC PCS 7
Process Control
System
SIMATIC
Controller/
Automation
System
SIMATIC HMI
Human Machine
Interface
Drive Systems/
SINAMICS
PROFIBUS PA
SENTRON
Circuit
Breakers
Sensor
Technology
IQ-Sense
SIMATIC
Distributed
I/O
SIMOTION
Motion Control
System
SINUMERIK
Numeric
Control
SIMOCODE-DP
Motor
Protection
and Control SINAMICS
SIMODRIVE
HART
SIWAREX
Weighing
Technology
modular
modula
r
1/6 Siemens KT10.1 · 2004
The add-on modules
The functionality of the basic units can be expanded using
add-on modules. The power supply is optimally integrated into
the overall system using the signalling module. Immediate
response to various operating statuses is possible and potential
damage can be avoided. The buffer module provides effective
protection against brief power failures which could lead to a
plant standstill, loss of data or even machine damage if the
24 V side is not buffered. A redundancy module can also be
used to provide redundant power supply. Thus the 24 V supply
is guaranteed even in the worst case when a faulty power
supply unit would affect the unit connected in parallel.
The SITOP select diagnosis module
The diagnosis module is the optimum expansion for all 24 V
power supplies in order to divide and monitor the load current
among several branch circuits. An overload or short-circuit in
a feeder is reliably detected and selectively switched-off. Total
failures of plants can be prevented because the 24 V supply
for the other loads is maintained. Detailed signalling permits
fast fault locating, and thus the minimizing of downtimes.
SITOP modular
The innovative SITOP modular power supplies feature a com-
pletely new concept. The highlight is the modular design
comprising a basic unit which can be supplemented by add-
on modules with further functions. The modularity has no
competition with respect to flexibility, simple handling and
price/performance ratio.
The basic units
Compact and rugged basic units for 1-, 2- or 3-phase connection
and with output currents from 5 A to 40 A are the basis of the
stabilized 24 V supply. The 5 A and 10 A power supply units
are unique, and can be connected to almost any network
throughout the world thanks to their ultra-wide input range.
Each basic unit can be fitted on a DIN rail and already has a
comprehensive scope of functions.
5 A and 10 A devices with ultra-wide input range for 1- and
2-phase operation
20 A and 40 A devices for 1- or 3-phase operation
Adjustable output voltage up to 28.8 V for compensation of
voltage drops
3 LEDs for detailed signalling of the operating status
Power boost up to three times the rated current
Selectable short-circuit response: constant current or latching
shutdown
Selectable output characteristic for parallel operation
Overview of product families
SITOP power
Introduction
DC UPS
The facet
s
1/7
Siemens KT10.1 · 2004
Tried and tested
SITOP DC UPS
The DC UPS modules provide optimum protection against
longer power failures. DC UPS modules and battery modules
expand SITOP power supply units with 24 V output voltage into
uninterruptible power supplies with a rated output current up
to 40 A. The transition from power supply mode to buffered
mode is absolutely interruption-free. The DC UPS modules are
provided as standard with all required protection and monitoring
functions, thus providing high availability. The integral battery
management function guarantees a long service life for the
maintenance-free battery modules. Status messages concerning
the operational readiness, battery status and battery lines are
signaled by LEDs and floating contacts. The compact 6 A and
15 A DC UPS modules can also communicate via an interface,
thus permitting simple integration into PC-based systems.
Overview of product families
SITOP power
Introduction
The facets
The SITOP power supply units also cover individual power
supply requirements - whether standard industrial applications,
extreme ambient conditions, or unusual output voltages. The
SITOP variants include some true all-rounders:
SITOP power 0.5: the mini devices with a width of only
22.5 mm are the narrowest in the SITOP family and are therefore
particularly suitable for supplying low-voltage switchgear.
SITOP power flexi: unlimited variety thanks to a variable output.
The innovative circuit concept permits flexible setting of the
output voltage between 3 V and 52 V. Special voltages can
therefore also be covered by a standard device.
SITOP power dual: the electronics supply for the switchgear
cabinet. The DIN rail device is industry-compatible and has
two 15 V outputs. For example, for electronic loads to be
supplied with ±15 V.
SITOP power 24 V/2.5 A, 4 A and 10 A: the devices with
universal input can be connected to 1-phase AC voltage
networks as well as to DC voltage networks.
SITOP power 24 V/20 A: the 2-phase primary switched-mode
regulator with 20 A rated output current is predestined for
industrial networks with high AC voltages. The special wide-
range input allows connection to 3-phase networks with rated
voltages between 500 V and 600 V.
SITOP power AS-Interface: 2 primary switched-mode regula-
tors are available especially for powering the actuator/sensor
interface: a 2.4 A version with 24 V DC input and IP65 degree
of protection, and a 7 A version with wide-range input for AC
and DC voltages.
Tried and tested
The SITOP range of power supply units has proven its reliability
for many years already. The units offer graded performances
with output currents from 2 A to 20 A and from 10 A to 40 A for
single-phase and three-phase incoming supplies respectively.
Thanks to the simple handling and numerous certifications, the
24 V power supply units are also suitable for export-oriented
use in all standard automation engineering applications. And
should it be the case that the power supply conditions are
unreliable in a global application, the proven SITOP power
supplies can of course also be combined with the DC UPS
modules.
SIMATIC design
LOGO!Powe
r
1/8 Siemens KT10.1 · 2004
LOGO!Power
The mini power supply units are available in two performance
classes for output voltages of 5 V, 12 V and 15 V, and in three
performance classes for 24 V. Their flat, cascaded profile even
permits installation in small distribution boards. The primary
switched-mode regulators have been completely innovated
and now require even less space for mounting, but with in-
creased functionality. For example, the new function "Constant
current in event of overload" even permits the connection of
difficult loads. Wide-range input, wide temperature range and
many certifications mean that the LOGO! power supply is a
universal device for use in numerous applications.
SITOP in SIMATIC design
The SITOP power supply units were developed with a design
based on the SIMATIC automation systems. However, their
special features mean that they can also be optimally used in
many other applications.
S7-200 design: 24 V/3.5 A. The flat power supply unit with the
design of the micro PLC is also particularly suitable for appli-
cations with a small overall height and a small switchgear
cabinet depth.
S7-300 design: 24 V/2 A, 5 A and 10 A. Designed as series-
connected power supply units for the S7-300 CPUs, they can
be simply snapped onto the S7 rail and connected to the CPU
by means of a connecting comb. The 2 A and 5 A devices are
also available as outdoor versions which are unaffected even
by temperatures from -25 °C to +70 °C or increased shock and
vibration load.
ET 200B design: 24 V/5 A and 10 A. The devices with a flat
design are particularly suitable when only limited mounting
depths are available. They find sufficient space even in covered
machine racks or pivoted frames.
ET 200X design: 24 V/10 A. The 10 A power supply unit with
IP65 degree of protection is suitable for the most rugged
industrial applications. Permitting any mounting position, the
power supply unit for distributed I/Os can handle ambient
temperatures from -25 °C to +55 °C.
Overview of product families
SITOP power
Introduction
Siemens KT10.1 · 2004 1/9
SITOP power
Selection guide
1
In order to assist you in finding the right stabilized power supply
for each application as quickly as possible, we have assembled
the following table as an overview listing all power supplies con-
tained in this catalog sorted according to input voltage, output
voltage and output current.
■
Selection guide
Continued on page 1/10.
Input voltage Alternating voltage Direct voltage
Output
voltage
Output
current
Order No. 120 to 230 V
AC
500 to 600 V
two-phase
AC
400 to 500 V
three-phase
AC
24 V DC 24 to 220 V
DC
120 to 230 V
DC
5 V DC 3 A 6EP1 311-1SH02 page 13/2
6.3 A 6EP1 311-1SH12 page 13/2
12 V DC 1.9 A 6EP1 321-1SH02 page 13/4
4.5 A 6EP1 322-1SH02 page 13/4
15 V DC 1.9 A 6EP1 351-1SH02 page 13/6
4 A 6EP1 352-1SH02 page 13/6
2x3.5 A 6EP1 353-0AA00 page 10/2
24 V DC 0.375 A 6EP1 731-2BA00 page 2/2
0.5 A 6EP1 331-2BA10 page 2/2
1.3 A 6EP1 331-1SH02 page 13/8
2 A 6EP1 331-2BA00
6EP1 331-1SL11
page 2/2
page 2/3
6ES7 307-1BA00-0AA0 page 2/3
6ES7 305-1BA80-0AA0 page 2/3
6EP1 732-0AA00 page 2/3
2.5 A 6EP1 332-1SH12 page 3/2 page 3/2
6EP1 332-1SH42 page 13/8
3.5 A 6EP1 332-1SH31 page 3/2
4 A 6EP1 332-1SH22 page 3/2 page 3/2
6EP1 332-1SH51 page 13/8
5 A 6EP1 333-2BA00 page 4/2
6EP1 333-2AA00 page 4/2
6ES7 307-1EA80-0AA0 page 4/3
6ES7 307-1EA00-0AA0 page 4/3
6EP1 333-1AL12 page 4/3
6EP1 333-1SL11 page 4/3
6EP1 333-3BA00 page 4/2 page 7/2
10 A 6EP1 334-2BA00 page 5/2
6EP1 334-2AA00 page 5/2
6EP1 334-2CA00 page 5/3
6ES7 307-1KA01-0AA0 page 5/3
6EP1 334-1SL12 page 5/3
6EP1 334-1AL12 page 5/3
6EP1 334-1SH01 page 5/3
6EP1 434-2BA00 page 7/6
6EP1 334-3BA00 page 5/2 page 7/2
20 A 6EP1 336-3BA00 page 6/2
6EP1 336-2BA00 page 6/3
6EP1 536-2AA00 page 6/3
6EP1 436-2BA00 page 7/6
6EP1 436-3BA00 page 7/3
30 A 6EP1 437-2BA00 page 7/7
40 A 6EP1 337-3BA00 page 6/2
6EP1 437-3BA00 page 7/3
6EP1 437-2BA10 page 7/7
Siemens KT10.1 · 2004
1/10
SITOP power
Selection guide
1
■
Selection guide (continued)
Input voltage Alternating voltage Direct voltage
Output
voltage
Output
current
Order No.
120 to 230 V
AC
500 to 600 V
two-phase
AC
400 to 500 V
three-phase
AC
24 V DC 24 to 220 V
DC
120 to 230 V
DC
24 V DC UPS 6 A 6EP1 931-2DC21 page 9/7
6EP1 931-2DC31 page 9/7
6EP1 931-2DC41 page 9/7
15 A 6EP1 931-2EC21 page 9/9
6EP1 931-2EC31 page 9/9
6EP1 931-2EC41 page 9/9
40 A 6EP1 931-2FC01 page 9/13
1.2 Ah 6EP1 935-6MC01 page 9/14
2.5 Ah 6EP1 935-6MD31 page 9/15
3.2 Ah 6EP1 935-6MD11 page 9/16
7 Ah 6EP1 935-6ME21 page 9/17
12 Ah 6EP1 935-6MF01 page 9/18
48 V DC 20 A 6EP1 457-3BA00 page 10/2
3-52 V DC 10 A/120 W 6EP1 353-2BA00 page 10/2
30 V DC 2.4 A 6EP1 632-1AL01 page 11/2
AS-Interface 7 A 6EP1 354-1AL01 page 11/2
SITOP power 24 V, Additional components
Signalling module 6EP1 961-3BA10 page 8/2
Buffer module 40 A 6EP1 961-3BA00 page 8/2
Redundancy
module 20 A 6EP1 961-3BA20 page 8/2
Diagnosis module 4x10 A 6EP1 961-2BA00 page 8/4
Siemens KT10.1 · 2004
2
Output currents up to 2 A
2/2 The smallest
2/2 The proven type
2/3 The DC/DC converter
2/3 The S7-300 type
2/3 The outdoor variant
SITOP power · Standard 24 V
Single-phase
Siemens KT10.1 · 2004
2/2
SITOP power · Standard 24 V
Output currents up to 2 A
Single-phase
2
■
Overview The smallest The proven type
■
Application
■
Technical specifications
Continued on page 2/4.
The optimum power supply units for automation solutions in the
lower performance range; with wide-range input for AC or DC
voltages; thanks to their compact and narrow design, they are
particularly suitable for solutions where limited space is avail-
able and in conjunction with low-voltage switchgear.
The tried and tested power
supply unit with selectable
input voltage range for sup-
plying all standard applica-
tions in automation engineer-
ing.
Power supply, type 0.5 A 0.375 A 2 A
Order No. 6EP1 331-2BA10 6EP1 731-2BA00 6EP1 331-2BA00
Input Single-phase AC DC voltage Single-phase AC
Rated voltage Vin rated 120 to 230 V AC
wide-range input 48 to 220 V DC
wide-range input 120/230 V AC
Settable using wire jumper
Voltage range 93 to 264 V AC 30 to 264 V DC
(30 to 187 V AC) 93 to 132 V/187 to 264 V AC
Overvoltage strength 2.3 x Vin rated, 1.3 ms - 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 10 ms at Vin = 230 V > 10 ms at Vin = 220 V > 10 ms at Vin = 93/187 V
Rated line frequency; range 50/60 Hz, 47 to 63 Hz -50/60 Hz; 47 to 63 Hz
Rated current Iin rated 0.22 to 0.13 A 0.03 to 0.06 A 0.9/0.6 A
Inrush current limitation (+25 °C) < 23 A, typ. 1 ms < 35 A, typ. 3 ms < 14 A, typ. 3 ms
I2t 0.3 A2s 1.2 A2s< 0.3 A
2s
Integrated line-side fuse T 2 A/250 V (not accessible) F 4 A/250 V (not accessible) T 1.6 A/250 V (not accessible)
Recommended circuit-breaker
(IEC 898) in mains supply line From 3 A, Characteristic C From 6 A, Characteristic C,
DC-suitable From 3 A, Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC 24 V DC
Total tolerance ± 3 % ± 3 % ± 3 %
• Stat. mains compensation Approx. ± 0.2 % Approx. ± 0.1 % Approx. 0.1 %
• Stat. load compensation Approx. ± 0.7 % Approx. ± 0.1 % Approx. 0.8 %
Residual ripple
(clock frequency:
approx. 50 kHz)
< 150 mVpp (typ. 50 mVpp)< 150 mVpp (typ. 50 mVpp)< 150 mVpp
Spikes (bandwidth: 20 MHz) < 240 mVpp (typ. 150 mVpp)< 240 mVpp (typ. 50 mVpp)< 240 mVpp
Setting range --22.8 to 26.4 V
Status display Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K.
Power ON/OFF behavior No overshoot of Vout
(soft start) No overshoot of Vout
(soft start) No overshoot of Vout
(soft start)
Starting delay/voltage rise < 1.5 s/typ. 20 ms < 2.5 s/typ. 90 ms < 3 s/typ. 80 ms
Rated current Iout rated 0.5 A 0.375 A 2 A
Current range
• Up to +45 °C 0 to 0.5 A 0 to 0.375 A 0 to 2 A
• Up to +60 °C 0 to 0.5 A (up to +70 °C) 0 to 0.375 A 0 to 2 A
Dyn. V/I with
• Starting on short circuit Approx. 0.6 A constant current
• Short-circuit in operation Approx. 0.6 A constant current typ. 2.7 A for 200 ms typ. 7 A for 300 ms
Parallel connection for increased
output Not permissible Not permissible Yes, 2
Siemens KT10.1 · 2004 2/3
SITOP power · Standard 24 V
Single-phase
Output currents up to 2 A 2
The DC/DC converter The S7-300 type The outdoor variant
Continued on page 2/5.
1) SIPLUS module 6AG1 307-1BA80-2AA0 for enhanced temperature range
-25 to +60 °C and use under medium load (e.g. chlorine/sulfur atmosphere).
Conformity with EN 50155 available soon (electrical equipment on track
vehicles).
The DC/DC converter for
supply from battery and DC
networks, with a wide input
voltage range from 38 V to
121 V DC.
The proven power supply in the SIMATIC S7-300 design; alter-
natively with PS-CPU connecting comb and for snap-mounting
on S7 busbar (Order No. 6ES7307-1BA00-0AA0) or without
PS-CPU connecting comb for snap-mounting on DIN rail
EN 500022-35x15 via mounting adapter
(Order No. 6EP1 331-1SL11).
The power supply unit for
extreme environmental con-
ditions with SIMATIC S7-300
design, can be snapped
onto S7 rail; with PS-CPU
connecting comb.
2 A 2 A 2 A 2 A
6EP1 732-0AA00 6ES7307-1BA00-0AA0 6EP1 331-1SL11 6ES7 305-1BA80-0AA0 1)
DC voltage Single-phase AC Single-phase AC DC voltage
48 to 110 V DC
wide-range input 120/230 V AC
Settable via selector switch on
device
120/230 V AC
Settable via selector switch on
device
24 to 110 V DC
wide-range input
38 to 121 V DC 85 to 132 V/170 to 264 V AC 85 to 132 V/170 to 264 V AC 16.8 to 138 V DC
2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms 154 V; 0.1 s
> 5 ms at Vin = 48 V > 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V > 10 ms at Vin rated
-50/60 Hz, 47 to 63 Hz 50/60 Hz, 47 to 63 Hz -
1.2 to 0.5 A 0.9/0.6 A 0.9/0.6 A 2.7 to 0.6 A (4 to 0.9 A)
< 33 A < 20 A, < 3 ms < 20 A, < 3 ms < 20 A, < 10 ms
< 1.0 A2s < 1.0 A2s < 5 A2s
T 2.5 A (not accessible) T 1.6 A/250 V (not accessible) T 1.6 A/250 V (not accessible) T 6.3 A/250 V (not accessible)
10 to 25 A, Characteristic B, or
6 to 25 A, Characteristic C,
DC-suitable
3 A, Characteristic C 3 A, Characteristic C From 10 A, Characteristic C,
DC-suitable
Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
24 V DC 24 V DC 24 V DC 24 V DC
±1% ±3% ±3% ±3%
Approx. 0.1 % Approx. 0.1 % Approx. 0.1 % Approx. 0.2 %
Approx. 0.4 % Approx. 0.2 % Approx. 0.2 % Approx. 0.4 %
< 100 mVpp < 150 mVpp (typ. < 20 mVpp)< 150 mVpp (typ. < 20 mVpp)< 150 mVpp (typ. < 30 mVpp)
< 300 mVpp < 240 mVpp (typ. < 150 mVpp)< 240 mVpp (typ. < 150 mVpp)< 240 mVpp (typ. < 150 mVpp)
----
Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K.
Overshoots of Vout when
switching on max. 25 V No overshoot of Vout
(soft start) No overshoot of Vout
(soft start) No overshoot of Vout
(soft start)
< 3 s/typ. 30 ms < 3 s/typ. 60 ms < 3 s/typ. 60 ms < 3 s (typ. 7 ms)/typ. 5 ms
2 A 2 A 2 A 2 A (3 A at Vin > 24 V)
0 to 2 A 0 to 2 A 0 to 2 A 0 to 2 A (3 A)
0 to 2 A (up to +70 °C) 0 to 2 A 0 to 2 A 0 to 2 A (3 A)
typ. 10 A for 90 ms typ. 10 A for 90 ms typ. 9 A for 270 ms
typ. 10 A for 90 ms typ. 10 A for 90 ms typ. 9 A for 270 ms
Yes, 2 Not permissible Not permissible Yes, 2
Siemens KT10.1 · 2004
2/4
SITOP power · Standard 24 V
Output currents up to 2 A
Single-phase
2
Power supply, type 0.5 A 0.375 A 2 A
Order No. 6EP1 331-2BA10 6EP1 731-2BA00 6EP1 331-2BA00
Efficiency
Efficiency at Vout rated, Iout rated Approx. 74 % Approx. 66 % Approx. 82 %
Power loss at Vout rated, Iout rated Approx. 4.2 W Approx. 4.6 W Approx. 11 W
Control
Dyn. mains compensation
(Vin rated ±15%) Approx. ± 0.3 % Vout Approx. ± 0.3 % Vout Approx. ± 0.3 % Vout
Dyn. load compensation
(Iout: 50/100/50 %) ±0.7% V
out ±0.4% V
out ±2% V
out
Settling time
• Load step from 50 to 100 % typ. 1.5 ms typ. 2 ms typ. 0.5 ms
• Load step from 100 to 50 % typ. 1.5 ms typ. 2 ms typ. 0.5 ms
Protection and monitoring
Output overvoltage protection Yes, acc. to EN 60950 Yes, acc. to EN 60950 Yes, acc. to EN 60950
Current limitation 0.55 to 0.65 A 0.41 to 0.49 A typ. 2.2 to 2.6 A
Short-circuit protection Stabilized current characteristic
down to 0 V Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart
RMS sustained short-circuit current < 0.65 A < 0.9 A < 4 A
Overload/short-circuit indicator ---
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I Class I
Discharge current < 3.5 mA < 3.5 mA < 3.5 mA (typ. 0.17 mA)
TÜV test Yes Yes Yes; CB scheme
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-95), File E143289;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
Yes, cULus listed (UL 508, CSA
22.2 No. 14-95), File E143289;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
FM approval - - -
Appr. for use in marine vessels - - -
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable Not applicable Not applicable
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range -20 to +70 °C with natural
convection -20 to +70 °C with natural con-
vection, derating above 60 °C 0 to +60 °C with natural
convection
Transportation and storage
temperature range -40 to +70 °C -40 to +70 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L, N, PE
(DC input: L+1, M1, PE) One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
• Output L+ 1 screw-type terminal for
0.5 to 2.5 mm21 screw-type terminal for
0.5 to 2.5 mm21 screw-type terminal for
0.5 to 2.5 mm2
• Output M 2 screw-type terminals for
0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 22.5 x 80 x 91 22.5 x 80 x 91 50 x 125 x 125
Weight approx. 0.11 kg 0.14 kg 0.38 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories ---
Siemens KT10.1 · 2004 2/5
SITOP power · Standard 24 V
Single-phase
Output currents up to 2 A 2
2 A 2 A 2 A 2 A
6EP1 732-0AA00 6ES7307-1BA00-0AA0 6EP1 331-1SL11 6ES7 305-1BA80-0AA0
Approx. 84 % Approx. 83 % Approx. 83 % Approx. 75 %
Approx. 9 W Approx. 10 W Approx. 10 W Approx. 16 W (24 W)
±0.3% V
out ±0.3% V
out ±0.3% V
out ±0.3% V
out
±0.8% V
out ±0.8% V
out ±0.8% V
out ±2.5% V
out
< 5 ms (typ. 2.5 ms) < 5 ms (typ. 2.5 ms) < 5 ms (typ. 2.5 ms) < 5 ms (typ. 2.5 ms)
< 5 ms (typ. 2.5 ms) < 5 ms (typ. 2.5 ms) < 5 ms (typ. 2.5 ms) < 5 ms (typ. 2.5 ms)
Yes, suppressor diode at output Additional control loop, shut-
down at approx. 30 V, automatic
restart
Additional control loop, shut-
down at approx. 30 V, automatic
restart
Additional control loop, shut-
down at approx. 30 V, automatic
restart
typ. 2.1 to 3 A 2.2 to 2.6 A 2.2 to 2.6 A 3.3 to 3.9 A
Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart
< 2 A < 4 A < 4 A < 2 A
----
Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178,
clearance and creepage dis-
tances > 5 mm
Class I Class I Class I Class I
< 3.5 mA (typ. 0.7 mA) < 3.5 mA (typ. 0.7 mA) < 3.5 mA (typ. 0.7 mA) < 3.5 mA (typ. 0.7 mA)
-Yes Yes Yes
Yes Yes Yes Yes
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E179336 Yes, UL listed (UL 508),
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508),
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508),
File E143289, CSA (CSA 22.2
No. 14-95)
- Yes, Class I Div. 2 Group A, B, C,
D T4 Yes, Class I Div. 2 Group A, B, C,
D T4 -
- in the S7-300 system in the S7-300 system Yes, GL, LRS
IP20 IP20 IP20 IP20
EN 55022 Class B EN 55022 Class B EN 55022 Class B EN 55011 Class A
Not applicable Not applicable Not applicable Not applicable
EN 61000-6-2 EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
0 to +70 °C with natural
convection 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection -25 to +70 °C with natural con-
vection
-40 to +70 °C -40 to +85 °C -40 to +85 °C -40 to +85 °C
Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K5 acc. to
EN 60721, brief condensation
permissible
One screw-type terminal each
for 2 x 0.5 to 2.5/1.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
1 screw-type terminal for
2 x 0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm2
1 screw-type terminal for
2 x 0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm2
80 x 135 x 120 50 x 125 x 120 50 x 125 x 135 80 x 125 x 120
0.5 kg 0.42 kg 0.42 kg 0.75 kg
Snap-mounting on DIN rail EN
50022-35x15 Snap-mounting on S7 rail Snap-mounting on DIN rail
EN 50022-35x15 Snap-mounting on S7 rail
- Mounting adapter for DIN rail
and PS-CPU connecting comb Mounting adapter for DIN rail
and PS-CPU connecting comb Mounting adapter for DIN rail
and PS-CPU connecting comb
Siemens KT10.1 · 2004
2/6
SITOP power · Standard 24 V
Notes
Single-phase
2
Siemens KT10.1 · 2004
3
Output currents 2.5 to 4 A
3/2 The universal types
3/2 The S7-200 type
SITOP power · Standard 24 V
Single-phase
Siemens KT10.1 · 2004
3/2
SITOP power · Standard 24 V
Output currents 2.5 to 4 A
Single-phase
3
■
Overview The universal types The S7-200 type
■
Application
■
Technical specifications
Continued on page 3/3.
The universal power supply units for all supply networks, with a
wide-range input from 93 V to 264 V AC and 110 V to 350 V DC
for supply from all typical networks.
Power supply unit whose de-
sign and functionality are opti-
mally matched to the SIMATIC
S7-200 micro PLC; flat design,
particularly suitable for low
control cabinet depths.
Power supply, type 2.5 A 4 A 3.5 A
Order No. 6EP1 332-1SH12 6EP1 332-1SH22 6EP1 332-1SH31
Input Single-phase AC or DC Single-phase AC or DC Single-phase AC
Rated voltage Vin rated 120 to 230 V AC
wide-range input 120 to 230 V AC
wide-range input 120/230 V AC
Settable using wire jumper
Voltage range 93 to 264 V AC or 110 to
350 V DC 93 to 264 V AC or 110 to
350 V DC 93 to 132 V/187 to 264 V AC
Overvoltage strength 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 20 ms at Vin = 120 V, > 80 ms
(typ. 100 ms) at Vin = 187 V > 20 ms at Vin = 120 V, > 80 ms
(typ. 100 ms) at Vin = 187 V > 20 ms at Vin = 187 V
Rated line frequency; range 0/50/60 Hz, 47 to 63 Hz 0/50/60 Hz, 47 to 63 Hz 50/60 Hz, 47 to 63 Hz
Rated current Iin rated 1.3 to 0.7 A 1.8 to 1.1 A 1.65/0.95 A
Inrush current limitation (+25 °C) < 33 A, < 3 ms (Vin = 230 V) < 33 A, < 3 ms (Vin = 230 V) < 33 A, < 3 ms (Vin = 230 V)
I2t < 3.5 A2s< 3.5 A
2s< 1.0 A
2s
Integrated line-side fuse T 3.15 A (not accessible) T 3.15 A (not accessible) T 2.5 A/250 V (not accessible)
Recommended circuit-breaker
(IEC 898) in mains supply line Two-pole circuit-breaker from
10 A, Characteristic C or from
6 A, Characteristic D
Two-pole circuit-breaker from
10 A, Characteristic C or from
6 A, Characteristic D
Two-pole circuit-breaker from
10 A, Characteristic C or from
6 A, Characteristic D
Output Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC 24 V DC
Total tolerance ± 1 % ± 1 % ± 5 % (typ. ± 2 %)
• Stat. mains compensation Approx. ± 0.1 % Approx. ± 0.1 % Approx. ± 0.1 %
• Stat. load compensation Approx. ± 0.2 % Approx. ± 0.2 % Approx. ± 0.2 %
Residual ripple (clock frequency:
approx. 50 kHz) < 50 mVpp (typ. 40 mVpp)< 50 mVpp (typ. 40 mVpp)< 150 mVpp (typ. 30 mVpp)
Spikes (bandwidth: 20 MHz) < 100 mVpp (typ. 40 mVpp)< 100 mVpp (typ. 40 mVpp)< 240 mVpp (typ. 110 mVpp)
Setting range ---
Status display Green LED for 24 V O.K. Green LED for 24 V O.K. -
Power ON/OFF behavior No overshoot of Vout
(soft start) No overshoot of Vout
(soft start) No overshoot of Vout
(soft start)
Starting delay/voltage rise < 0.6 s/typ. 20 ms < 0.6 s/typ. 20 ms < 1 s/typ. 80 ms
Rated current Iout rated 2.5 A 4 A 3.5 A
Current range
• Up to +45 °C 0 to 2.5 A 0 to 4 A 0 to 3.5 A
• Up to +60 °C 0 to 2.5 A 0 to 2.5 A 0 to 3.5 A
Dyn. V/I with
• Starting on short circuit Approx. 2.8 A constant current Approx. 4.4 A constant current typ. 5 A for 100 ms
• Short-circuit in operation Approx. 2.8 A constant current Approx. 4.4 A constant current typ. 5 A for 100 ms
Parallel connection for increased
output Yes, up to 10 Yes, up to 10 Yes, up to 5
Siemens KT10.1 · 2004 3/3
SITOP power · Standard 24 V
Single-phase
Output currents 2.5 to 4 A
3
Power supply, type 2.5 A 4 A 3.5 A
Order No. 6EP1 332-1SH12 6EP1 332-1SH22 6EP1 332-1SH31
Efficiency
Efficiency at Vout rated, Iout rated Approx. 85 % Approx. 85 % Approx. 84 %
Power loss at Vout rated, Iout rated Approx. 11 W Approx. 17 W Approx. 16 W
Control
Dyn. mains compensation, typ.
(Vin rated ±15 %) ±0.3% V
out ±0.3% V
out ±0.3% V
out
Dyn. load compensation
(Iout: 50/100/50 %) typ. ± 0.5 % Vout typ. ± 0.5 % Vout < ± 10 % Vout (typ. ± 3 % Vout)
Settling time
• Load step from 50 to 100 % < 2 ms (typ. 1 ms) < 2 ms (typ. 1 ms) < 5 ms
• Load step from 100 to 50 % < 2 ms (typ. 1 ms) < 2 ms (typ. 1 ms) < 5 ms
Protection and monitoring
Output overvoltage protection
Current limitation 2.8 A 4.4 A 3.8 A
Short-circuit protection Stabilized current characteristic
down to 0 V Stabilized current characteristic
down to 0 V Stabilized current characteristic
to typ. 14 V, electronic shut-
down below that, automatic
restart
RMS sustained short-circuit current < 3 A < 5 A < 4 A
Overload/short-circuit indicator ---
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I Class I
Discharge current < 3.5 mA < 3.5 mA < 3.5 mA
TÜV test Yes Yes Yes
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289
FM approval - - -
Appr. for use in marine vessels - - -
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable - EN 61000-3-2
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +50 °C with natural
convection 0 to +60 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L, N, PE One screw-type terminal each
for 2 x 0.5 to 1.5 mm2 finely
stranded, 2 x 0.5 to 2.5 mm2
single-core
One screw-type terminal each
for 2 x 0.5 to 1.5 mm2 finely
stranded, 2 x 0.5 to 2.5 mm2
single-core
One screw-type terminal each
for 0.5 to 1 mm2 finely stranded,
0.5 to 1.5 mm2 single-core
• Output L+ 1 screw-type terminal for
2 x 0.5 to 2.5 mm21 screw-type terminal for
2 x 0.5 to 2.5 mm21 screw-type terminal for
0.5 to 1 mm2
• Output M 1 screw-type terminal for
2 x 0.5 to 2.5 mm21 screw-type terminal for
2 x 0.5 to 2.5 mm22 screw-type terminals for
0.5 to 1 mm2
Dimensions
(W x H x D) in mm 80 x 135 x 120 80 x 135 x 120 160 x 80 x 62
Weight approx. 0.5 kg 0.5 kg 0.5 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15, wall mounting Snap-mounting on DIN rail
EN 50022-35x15, wall mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5,
wall mounting
Accessories - - Mounting bracket
Siemens KT10.1 · 2004
3/4
SITOP power · Standard 24 V
Notes
Single-phase
3
Siemens KT10.1 · 2004
4
Output current 5 A
4/2 SITOP modular
4/2 The proven types
4/3 The S7-300 type
4/3 The outdoor variant
4/3 The flat design
SITOP power · Standard 24 V
Single-phase and
two-phase
Siemens KT10.1 · 2004
4/2
SITOP power · Standard 24 V
Output current 5 A
Single-phase and two-phase
4
■
Overview SITOP modular The proven types
■
Application
■
Technical specifications
Continued on page 4/4.
The modular power supply
unit with single-phase and
two-phase wide-range inputs
for global use in many differ-
ent fields of application; ex-
pansion of functions possible
using add-on modules.
The tried and tested power supply unit with selectable input volt-
age range for supplying all standard applications in automation
engineering; 6EP1333-2AA00 without limitation of input current
harmonics.
Power supply, type 5 A 5 A 5 A
Order No. 6EP1 333-3BA00 6EP1 333-2BA00 6EP1 333-2AA00
Input Single and two-phase AC Single-phase AC Single-phase AC
Rated voltage Vin rated 120/230 to 500 V AC
Settable via selector switch on
device
120/230 V AC
Settable using wire jumper 120/230 V AC
Settable using wire jumper
Voltage range 85 to 132 V/176 to 550 V AC 93 to 132 V/187 to 264 V AC 93 to 132 V/187 to 264 V AC
Overvoltage strength 1300 Vpeak, 1.3 ms 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 25 ms at Vin = 120/230 V > 10 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 2.2 /1.2 to 0.61 A 2.2/0.9 A 2.2/1.3 A
Inrush current limitation (+25 °C) < 35 A < 32 A, typ. 3 ms < 32 A, typ. 3 ms
I2t < 1.7 A2s< 0.8 A
2s < 0.8 A2s
Integrated line-side fuse T 3, 15 A (not accessible) T 3.15 A/250 V (not accessible) T 3.15 A/250 V (not accessible)
Recommended circuit-breaker
(IEC 898) in mains supply line From 6 A (10 A) Characteristic C
(B); with two-phase operation:
circuit-breaker with two-pole
connection or motor circuit-
breaker 3RV1021-1EA10
From 6 A, Characteristic C From 6 A, Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC 24 V DC
Total tolerance ± 3 % ± 3 % ± 3 %
• Stat. mains compensation Approx. 0.1 % Approx. 0.1 % Approx. 0.1 %
• Stat. load compensation Approx. 0.1 % Approx. 0.2 % Approx. 0.2 %
Residual ripple (clock frequency:
approx. 50 kHz) < 50 mVpp (typ. 10 mVpp)< 150 mVpp < 150 mVpp
Spikes (bandwidth: 20 MHz) < 200 mVpp (typ. 20 mVpp)< 240 mVpp < 240 mVpp
Setting range 24 to 28.8 V (max. 120 W) 22.8 to 26.4 V 22.8 to 26.4 V
Status display Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K.
Power ON/OFF behavior Overshoot of Vout approx. 3 % No overshoot of Vout (soft start) No overshoot of Vout (soft start)
Starting delay/voltage rise < 1 s/< 50 ms < 3 s/typ. 80 ms < 3 s/typ. 80 ms
Rated current Iout rated 5 A 5 A 5 A
Current range
• Up to +45 °C 0 to 5 A 0 to 5 A 0 to 5 A
• Up to +60 °C 0 to 5 A 0 to 5 A 0 to 5 A
Dyn. V/I with
• Starting on short circuit Approx. 5.5 A constant current
• Short-circuit in operation typ. 15 A for 25 ms typ. 20 A for 350 ms typ. 20 A for 350 ms
Parallel connection for increased
output Yes, 2 (selectable current char-
acteristic) Yes, 2 Yes, 2
Siemens KT10.1 · 2004 4/3
SITOP power · Standard 24 V
Single-phase and two-phase
Output current 5 A
4
The S7-300 type The outdoor variant The flat design
Continued on page 4/5.
1) SIPLUS module 6AG1 307-1EA80-2AA0 for enhanced temperature range
-25 to +60 °C and use under medium load (e.g. chlorine/sulfur atmo-
sphere). Conformity with EN 50155 available soon (electrical equipment on
track vehicles).
The proven power supply in the SIMATIC S7-300 design; alter-
natively with PS-CPU connecting comb for snap-mounting on S7
busbar (Order No. 6ES7307-1EA00-0AA0) or without PS-CPU
connecting comb for snap-mounting on DIN rail EN 500022-
35x15 via mounting adapter (Order No. 6EP1 333-1SL11).
The power supply unit for ex-
treme environmental condi-
tions with SIMATIC S7-300 de-
sign, can be snapped onto S7
rail; with PS-CPU connecting
comb.
The flat design which is of
great advantage where only
low mounting depths are
available, e.g. for use with
distributed I/O, in machine
benches or alcoves; design
matched to SIMATIC ET 200B.
5 A 5 A 5 A 5 A
6ES7 307-1EA00-0AA0 6EP1 333-1SL11 6ES7 307-1EA80-0AA0 1) 6EP1 333-1AL12
Single-phase AC Single-phase AC Single-phase AC Single-phase AC
120/230 V AC
Settable via selector switch on
device
120/230 V AC
Settable via selector switch on
device
120/230 V AC
Settable via selector switch on
device
120/230 V AC
Settable via selector switch on
device
85 to 132 V/170 to 264 V AC 85 to 132 V/170 to 264 V AC 93 to 132 V/187 to 264 V AC 85 to 132 V/170 to 264 V AC
2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
> 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V
50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 50/60 Hz, 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
2.1/1.3 A 2.1/1.3 A 2.1/1.2 A 2.2/1.2 A
< 45 A, < 3 ms < 45 A, < 3 ms < 45 A, < 3 ms < 32 A, < 3 ms
< 1.2 A2s < 1.2 A2s < 1.8 A2s (typ. 1.2 A2s) < 0.8 A2s
F 4 A/250 V (not accessible) F 4 A/250 V (not accessible) T 3.15 A/250 V (not accessible) T 3.15 A/250 V (not accessible)
From 6 A, Characteristic C From 6 A, Characteristic C From 10 A, Characteristic C or
from 6 A, Characteristic D From 6 A, Characteristic C
Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
24 V DC 24 V DC 24 V DC 24 V DC
±3% ±3% ±3 % ±1%
Approx. 0.1 % Approx. 0.1 % Approx. ± 0.2 % Approx. 0.1 %
Approx. 0.2 % Approx. 0.2 % Approx. ± 0.4 % Approx. 0.5 %
< 150 mVpp (typ. 40 mVpp)< 150 mVpp (typ. 40 mVpp)< 150 mVpp (typ. 40 mVpp)< 150 mVpp (typ. 40 mVpp)
< 240 mVpp (typ. 90 mVpp)< 240 mVpp (typ. 90 mVpp)< 240 mVpp (typ. 90 mVpp)< 240 mVpp (typ. 100 mVpp)
---22 to 29 V
Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K.
No overshoot of Vout (soft start) No overshoot of Vout (soft start) No overshoot of Vout (soft start) No overshoot of Vout (soft start)
< 2 s/typ. 60 ms < 2 s/typ. 60 ms < 3 s/typ. 100 ms < 2 s/typ. 40 ms
5 A 5 A 5 A 5 A
0 to 5 A 0 to 5 A 0 to 5 A 0 to 5 A
0 to 5 A 0 to 5 A 0 to 5 A 0 to 5 A
typ. 20 A for 75 ms typ. 20 A for 75 ms typ. 20 A for 180 ms typ. 20 A for 500 ms
typ. 20 A for 75 ms typ. 20 A for 75 ms typ. 20 A for 80 ms typ. 20 A for 500 ms
Not permissible Not permissible Not permissible Yes, 2
Siemens KT10.1 · 2004
4/4
SITOP power · Standard 24 V
Output current 5 A
Single-phase and two-phase
4
Power supply, type 5 A 5 A 5 A
Order No. 6EP1 333-3BA00 6EP1 333-2BA00 6EP1 333-2AA00
Efficiency
Efficiency at Vout rated, Iout rated Approx. 87 % Approx. 87 % Approx. 87 %
Power loss at Vout rated, Iout rated Approx. 18 W Approx. 18 W Approx. 18 W
Control
Dyn. mains compensation
(Vin rated ±15 %) Approx. 0.1% Approx. ± 0.3 % Vout Approx. ± 0.3 % Vout
Dyn. load compensation
(Iout: 50/100/50 %) Approx. +3 % Vout ±2.5% V
out ±2.5% V
out
Settling time
• Load step from 50 to 100 % < 5 ms (typ. 2 ms) typ. 0.2 ms typ. 0.2 ms
• Load step from 100 to 50 % < 5 ms (typ. 2 ms) typ. 0.2 ms typ. 0.2 ms
Protection and monitoring
Output overvoltage protection < 35 V Yes, acc. to EN 60950 Yes, acc. to EN 60950
Current limitation typ. 5.5 A typ. 5.5 to 6.5 A typ. 5.5 to 6.5 A
Short-circuit protection Choice of stabilized current
characteristic approx. 5.5 A or
latching shutdown
Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart
RMS sustained short-circuit current Approx. 5.5 A < 17 A < 17 A
Overload/short-circuit indicator Yellow LED for "overload", red
LED for "latching shutdown" - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I Class I
Discharge current < 3.5 mA (typ. 0.25 mA) < 3.5 mA (typ. 0.4 mA) < 3.5 mA (typ. 0.4 mA)
TÜV test Yes Yes; CB scheme Yes; CB scheme
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259 Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
FM approval - - -
Appr. for use in marine vessels - - -
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B EN 55022 Class B
Line harmonics limitation EN 61000-3-2 EN 61000-3-2 -
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L, N, PE One screw-type terminal each
for 0.2 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
• Output L+ 2 screw-type terminals for
0.2 to 2.5 mm21 screw-type terminal for
0.5 to 2.5 mm21 screw-type terminal for
0.5 to 2.5 mm2
• Output M 2 screw-type terminals for
0.2 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 70 x 125 x 125 75 x 125 x 125 75 x 125 x 125
Weight approx. 1.2 kg 0.75 kg 0.57 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories Buffer module (6EP1961-3BA00)
Signalling module (6EP1961-
3BA10)
Redundancy module (6EP1961-
3BA20)
--
Siemens KT10.1 · 2004 4/5
SITOP power · Standard 24 V
Single-phase and two-phase
Output current 5 A
4
5 A 5 A 5 A 5 A
6ES7 307-1EA00-0AA0 6EP1 333-1SL11 6ES7 307-1EA80-0AA0 6EP1 333-1AL12
Approx. 87 % Approx. 87 % Approx. 84 % Approx. 88 %
Approx. 18 W Approx. 18 W Approx. 23 W Approx. 17 W
±0.3% V
out ±0.3% V
out ±0.3% V
out ±0.3% V
out
±2.5% V
out ±2.5% V
out ±3% V
out ±0.5% V
out
typ. 0.1 ms typ. 0.1 ms < 5 ms (typ. 0.2 ms) < 5 ms (typ. 0.1 ms)
typ. 0.1 ms typ. 0.1 ms < 5 ms (typ. 0.2 ms) < 5 ms (typ. 0.1 ms)
Additional control loop, shut-
down at approx. 30 V, automatic
restart
Additional control loop, shut-
down at approx. 30 V, automatic
restart
Additional control loop, shut-
down at approx. 30 V, automatic
restart
Additional control loop, shut-
down at approx. 33 V, automatic
restart
5.5 to 6.5 A 5.5 to 6.5 A 5.5 to 6.5 A 5.5 to 6.5 A
Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart
< 9 A < 9 A < 5 A < 5 A
----
Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178,
clearance and creepage dis-
tances > 8 mm
Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Class I Class I Class I Class I
< 3.5 mA (typ. 0.3 mA) < 3.5 mA (typ. 0.3 mA) < 3.5 mA (typ. 0.3 mA) < 3.5 mA (typ. 0.26 mA)
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259
Yes, Class I Div. 2 Group A, B, C,
D, T 4 Yes, Class I Div. 2 Group A, B, C,
D, T 4 --
in the S7-300 system in the S7-300 system Yes, GL, LRS -
IP20 IP20 IP20 IP20
EN 55022 Class B EN 55022 Class B EN 55011 Class A EN 55022 Class B
EN 61000-3-2 EN 61000-3-2 - -
EN 61000-6-2 EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
0 to +60 °C with natural
convection 0 to +60 °C with natural
convection -40 to +70 °C with natural
convection 0 to +60 °C with natural
convection
-40 to +85 °C -40 to +85 °C -40 to +85 °C -25 to +85 °C
Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K5 acc. to
EN 60721, brief condensation
permissible
Climatic class 3K3 acc. to
EN 60721, no condensation
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
3 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm2
3 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm2
80 x 125 x 120 80 x 125 x 135 80 x 125 x 120 160 x 130 x 60
0.74 kg 0.74 kg 0.57 kg 0.6 kg
Snap-mounting on S7 rail Snap-mounting on DIN rail
EN 50022-35x15 Snap-mounting on S7 rail Snap-mounting on DIN rail
EN 50022-35x15/7.5
Mounting adapter for DIN rail
and connecting comb Mounting adapter for DIN rail
and connecting comb Mounting adapter for DIN rail
and connecting comb Mounting bracket
Siemens KT10.1 · 2004
4/6
SITOP power · Standard 24 V
Notes
Single-phase and two-phase
4
Siemens KT10.1 · 2004
5
Output current 10 A
5/2 SITOP modular
5/2 The proven types
5/3 The IP65 version
5/3 The S7-300 type
5/3 The flat design
5/3 The universal type
SITOP power · Standard 24 V
Single-phase and
two-phase
Siemens KT10.1 · 2004
5/2
SITOP power · Standard 24 V
Output current 10 A
Single-phase and two-phase
5
■
Overview SITOP modular The proven types
■
Application
■
Technical specifications
Continued on page 5/4.
The modular power supply
unit with single-phase and
two-phase wide-range inputs
for global use in many differ-
ent fields of application; ex-
pansion of functions possible
using add-on modules.
The tried and tested power supply unit with selectable input volt-
age range for supplying all standard applications in automation
engineering; 6EP1334-2AA00 without limitation of input current
harmonics.
Power supply, type 10 A 10 A 10 A
Order No. 6EP1 334-3BA00 6EP1 334-2BA00 6EP1 334-2AA00
Input Single and two-phase AC Single-phase AC Single-phase AC
Rated voltage Vin rated 120/230 to 500 V AC
Settable via selector switch on
device
120/230 V AC
Settable using wire jumper 120/230 V AC
Settable using wire jumper
Voltage range 85 to 132/176 to 550 V AC 85 to 132/187 to 264 V AC 85 to 132/187 to 264 V AC
Overvoltage strength 1300 Vpeak, 1.3 ms 2.3 x Vin rated, 1.3ms 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 25 ms at Vin = 120/230 V > 10 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 4.4 /2.4 to 1.1 A 5.5/2.1 A 5.5/3.2 A
Inrush current limitation (+25 °C) < 35 A < 65 A, typ. 3 ms < 65 A, typ. 3 ms
I2t < 4.0 A2s< 3.3 A
2s< 3.3 A
2s
Integrated line-side fuse T 6.3 A (not accessible) T 6.3 A/250 V (not accessible) T 6.3 A/250 V (not accessible)
Recommended circuit-breaker
(IEC 898) in mains supply line From 6 A (10 A) Characteristic C
(B); with two-phase operation:
circuit-breaker with two-pole
connection or motor circuit-
breaker 3RV1021-1EA10
From 10 A, Characteristic C From 10 A, Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC 24 V DC
Total tolerance ± 3 % ± 3 % ± 3 %
• Stat. mains compensation Approx. 0.1 % Approx. 0.2 % Approx. 0.2 %
• Stat. load compensation Approx. 0.1 % Approx. 1 % Approx. 1 %
Residual ripple (clock frequency:
approx. 50 kHz) < 50 mVpp (typ. 10 mVpp)< 150 mVpp < 150 mVpp
Spikes (bandwidth: 20 MHz) < 200 mVpp (typ. 20 mVpp)< 240 mVpp < 240 mVpp
Setting range 24 to 28.8 V (max. 240 W) 22.8 to 28.8 V 22.8 to 28.8 V
Status display Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K.
Power ON/OFF behavior Overshoot of Vout approx. 3% No overshoot of Vout
(soft start) No overshoot of Vout
(soft start)
Starting delay/voltage rise < 1 s/< 50 ms < 3 s/typ. 80 ms < 3 s/typ. 80 ms
Rated current Iout rated 10 A 10 A 10 A
Current range
• Up to +45 °C 0 to 10 A 0 to 12 A 0 to 12 A
• Up to +60 °C 0 to 10 A 0 to 10 A 0 to 10 A
Dyn. V/I with
• Starting on short circuit Approx. 12 A constant current
• Short-circuit in operation typ. 30 A for 25 ms typ. 38 A for 200 ms typ. 38 A for 200 ms
Parallel connection for increased
output Yes, 2 (selectable current
characteristic) Yes, 2 Yes, 2
Siemens KT10.1 · 2004 5/3
SITOP power · Standard 24 V
Single-phase and two-phase
Output current 10 A
5
The IP65 version The S7-300 type The flat design The universal type
Continued on page 5/5.
Power supply unit with IP65
degree of protection, design
and functionality optimally
matched to ET 200X distrib-
uted I/O devices. When using
without ET 200X, the connec-
tor seal accessory is required.
The proven power supply in
the SIMATIC S7-300 design;
alternatively with PS-CPU
connecting comb for snap-
mounting on S7 busbar or
without connecting comb for
snap-mounting on DIN rail
EN 500022-35x15 via mount-
ing adapter.
The flat design which is of
great advantage where only
low mounting depths are
available, e.g. for use with dis-
tributed I/O, in machine
benches or alcoves; design
matched to SIMATIC ET 200B.
The universal power supply
unit for all supply networks,
with a wide-range input from
93 V to 264 V AC and 110 V to
350 V DC for supply from all
typical networks.
10 A 10 A 10 A 10 A
6EP1 334-2CA00 6ES7 307-1KA01-0AA0 /
6EP1334-1SL12
6EP1 334-1AL12 6EP1 334-1SH01
Single-phase AC Single-phase AC Single-phase AC Single-phase AC
120/230 V AC
Settable using wire jumper 120/230 V AC
Settable via selector switch on
device
120/230 V AC
Settable via selector switch on
device
120 to 230 V AC
wide-range input
93 to 132/187 to 264 V AC 85 to 132/170 to 264 V AC 85 to 132/170 to 264 V AC 93 to 264 V AC or 110 to
350 V DC
2.3 x Vin rated, 1.3ms 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
> 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V > 20 ms at Vin = 93/187 V
50/60 Hz, 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 0/50/60 Hz; 47 to 63 Hz
4.3/2.6 A 4.1/1.8 A 4/2.5 A 2.5 to 1.3 A
< 65 A, typ. 3 ms < 55 A, < 3 ms < 65 A, < 3 ms < 20 A, < 3 ms
< 2.5 A2s < 3.3 A2s < 3.3 A2s < 1.5 A2s
T 6.3 A/250 V (not accessible) T 6.3 A/250 V (not accessible) T 6.3 A/250 V (not accessible) T 6.3 A (not accessible)
From 16 A, Characteristic C From 10 A, Characteristic C From 10 A, Characteristic C From 16 A, Characteristic C
Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
24 V DC 24 V DC 24 V DC 24 V DC
±3% ±3% ±1% ±1%
Approx. 0.2 % Approx. 0.1 % Approx. 0.1 % < ± 0.1 %
Approx. 1 % Approx. 0.5 % Approx. 0.5 % < ± 0.2 %
< 150 mVpp < 150 mVpp (typ. 40 mVpp)< 150 mVpp (typ. 50 mVpp)< 100 mVpp
< 240 mVpp < 240 mVpp (typ. 100 mVpp)< 240 mVpp (typ. 200 mVpp)< 100 mVpp
22.8 to 25.2 V -22 to 29 V -
Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K. Green LED for 24 V O.K.
No overshoot of Vout
(soft start) No overshoot of Vout
(soft start) No overshoot of Vout
(soft start) No overshoot of Vout
(soft start)
< 3 s/typ. 80 ms < 1.5 s/typ. 80 ms < 2 s/typ. 40 ms < 3 s/typ. 100 ms
10 A 10 A 10 A 10 A
0 to 10 A (up to +40 °C) 0 to 10 A 0 to 10 A 0 to 10 A
0 to 8 A (up to +55 °C) 0 to 10 A 0 to 10 A 0 to 10 A
typ. 35 A for 80 ms typ. 35 A for 700 ms Approx. 11 A constant current
typ. 38 A for 200 ms typ. 35 A for 150 ms typ. 35 A for 700 ms Approx. 11 A constant current
Yes, 2 Not permissible Yes, 2 Yes, 2
Siemens KT10.1 · 2004
5/4
SITOP power · Standard 24 V
Output current 10 A
Single-phase and two-phase
5
Power supply, type 10 A 10 A 10 A
Order No. 6EP1 334-3BA00 6EP1 334-2BA00 6EP1 334-2AA00
Efficiency
Efficiency at Vout rated, Iout rated Approx. 87 % Approx. 89 % Approx. 89 %
Power loss at Vout rated, Iout rated Approx. 36 W Approx. 30 W Approx. 30 W
Control
Dyn. mains compensation
(Vin rated ±15%) Approx. 0.1 % Approx. ± 0.3 % Vout Approx. ± 0.3 % Vout
Dyn. load compensation
(Iout: 50/100/50 %) Approx. +3 % Vout ±5% V
out ±5% V
out
Settling time
• Load step from 50 to 100 % < 5 ms (typ. 2 ms) typ. 0.2 ms typ. 0.2 ms
• Load step from 100 to 50 % < 5 ms (typ. 2 ms) typ. 0.2 ms typ. 0.2 ms
Protection and monitoring
Output overvoltage protection < 35 V Yes, acc. to EN 60950 Yes, acc. to EN 60950
Current limitation typ. 12 A typ. 13 to 15 A typ. 13 to 15 A
Short-circuit protection Choice of stabilized current
characteristic approx. 12 A or
latching shutdown
Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart
RMS sustained short-circuit current Approx. 12 A < 21 A < 21 A
Overload/short-circuit indicator Yellow LED for "overload", red
LED for "latching shutdown" - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I Class I
Discharge current < 3.5 mA (typ. 0.32 mA) < 3.5 mA (typ. 0.4 mA) < 3.5 mA (typ. 0.4 mA)
TÜV test Yes Yes; CB scheme Yes; CB scheme
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508,
CSA 22.2 No. 14-M91)
File E197259
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
FM approval - - -
Appr. for use in marine vessels - - -
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B EN 55022 Class B
Line harmonics limitation EN 61000-3-2 EN 61000-3-2 -
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L, N, PE One screw-type terminal each
for 0.2 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
• Output L+ 2 screw-type terminals for
0.2 to 2.5 mm21 screw-type terminal for
0.5 to 2.5 mm21 screw-type terminal for
0.5 to 2.5 mm2
• Output M 2 screw-type terminals for
0.2 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm22 screw-type terminals for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 90 x 125 x 125 100 x 125 x 135 100 x 125 x 135
Weight approx. 1.4 kg 1.08 kg 0.78 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories Buffer module (6EP1961-3BA00)
Signalling module (6EP1961-
3BA10)
Redundancy module (6EP1961-
3BA20)
--
Siemens KT10.1 · 2004 5/5
SITOP power · Standard 24 V
Single-phase and two-phase
Output current 10 A
5
1) Order No. 6ES7307-1KA01-0AA0.
2) Order No. 6EP1334-1SL12.
10 A 10 A 10 A 10 A
6EP1 334-2CA00 6ES7 307-1KA01-0AA0 /
6EP1334-1SL12
6EP1 334-1AL12 6EP1 334-1SH01
Approx. 87 % Approx. 87 % Approx. 89 % Approx. 85 %
Approx. 36 W Approx. 34 W Approx. 30 W Approx. 42 W
±0.3%V
out ±0.3% V
out ±0.3% V
out ±0.3% V
out
±5% V
out ±2.5% V
out ±0.6% V
out ±1.5% V
out
typ. 0.2 ms < 5 ms < 5 ms (typ. 0.1 ms) < 20 ms (typ. 10 ms)
typ. 0.2 ms < 5 ms < 5 ms (typ. 0.2 ms) < 20 ms (typ. 10 ms)
Yes, acc. to EN 60950 Additional control loop, shut-
down at approx. 30 V, automatic
restart
Additional control loop, shut-
down at approx. 33 V, automatic
restart
Yes, acc. to EN 60950
typ. 9 to 11 A 11 to 12 A 11 to 13 A 11 to 13 A
Choice of automatic restart or
latching shutdown Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart Stabilized current characteristic
down to 0 V
< 21 A < 10 A < 10 A < 14 A
Red LED for overtemperature
switch-off ---
Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950
Class I Class I Class I Class I
< 3.5 mA (typ. 0.9 mA) < 3.5 mA (typ. 0.5 mA) < 3.5 mA (typ. 0.27 mA) < 3.5 mA
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289
- Yes, Class I Div. 2, A, B, C, D, T4 - -
- in the S7-300 system - -
IP65 IP20 IP20 IP20
EN 55011 Class A EN 55022 Class B EN 55022 Class B EN 55022 Class B
- EN 61000-3-2 - EN 61000-3-2
EN 61000-6-2 EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
-25 to +55 °C (power derating
above +40 °C) 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
-40 to +70 °C -40 to +85 °C -25 to +85 °C -25 to +85 °C
Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Screw-type terminals
0.5 to 2.5 mm2 (PG11 screwed
gland)
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
Screw terminals, or connection
via expansion interface on the
backplane bus of the ET 200X
4 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm2
Screw terminals, or connection
via expansion interface on the
backplane bus of the ET 200X
4 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm23 screw-type terminals for
0.5 to 2.5 mm2
140 x 270 x 126 120 x 125 x 120 1)
120 x 125 x 135 2) 160 x 130 x 60 200 x 125 x 135
1.7 kg 1.1 kg 0.72 kg 1.8 kg
Wall mounting, any mounting
position Snap-mounting on S7 rail 1)
Snap-mounting on DIN rail
EN 50022-35x15 2)
Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15 or on S7 rail
IP65 connector seal Mounting adapter for DIN rail
and PS-CPU connecting comb Mounting bracket -
Siemens KT10.1 · 2004
5/6
SITOP power · Standard 24 V
Notes
Single-phase and two-phase
5
Siemens KT10.1 · 2004
6
Output currents 20 A and 40 A
6/2 SITOP modular
6/3 The proven type
6/3 The two-phase version
SITOP power · Standard 24 V
Single-phase and
two-phase
Siemens KT10.1 · 2004
6/2
SITOP power · Standard 24 V
Output currents 20 A and 40 A
Single-phase and two-phase
6
■
Overview SITOP modular SITOP modular
■
Application
■
Technical specifications
Continued on page 6/4.
1) Derating in 120 V operation necessary.
The modular power supply units with single-phase and two-
phase inputs for global use in many different fields of applica-
tion; expansion of functions possible using add-on modules.
Power supply, type 20 A 40 A
Order No. 6EP1 336-3BA00 6EP1 337-3BA00
Input Single/two-phase AC Single/two-phase AC
Rated voltage Vin rated 120/230 V AC
Settable using wire jumper on
device
120/230 V AC
Settable using wire jumper on
device
Voltage range 85 to 132/176 to 264 V 85 to 132/176 to 264 V
Overvoltage strength 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 20 ms at Vin = 230 V > 20 ms at Vin = 230 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 7.7/3.5 A 15/8 A
Inrush current limitation (+25 °C) < 60 A < 125 A
I2t < 9.9 A2s < 26 A2s
Integrated line-side fuse Yes Yes
Recommended circuit-breaker
(IEC 898) in mains supply line 10 A Char. C (2-pole coupled
with 2-phase operation) or motor
circuit-breaker 3RV1421-...
20 A Char. C (2-pole coupled
with 2-phase operation) or motor
circuit-breaker 3RV1421-...
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Total tolerance ± 3 % ± 3 %
• Stat. mains compensation Approx. 0.1 % Approx. 0.1 %
• Stat. load compensation Approx. 0.1 % Approx. 0.1 %
Residual ripple (clock frequency:
approx. 50 kHz) < 100 mVpp (typ. 30 mVpp)< 100 mVpp (typ. 60 mVpp)
Spikes (bandwidth: 20 MHz) < 200 mVpp (typ. 60 mVpp)< 200 mVpp (typ. 120 mVpp)
Setting range 24 to 28.8 V (max. 480 W) 24 to 28.8 V (max. 960 W)
Status display Green LED for 24 V O.K. Green LED for 24 V O.K.
Power ON/OFF behavior Overshoot of Vout approx. 3 % Overshoot of Vout approx. 3 %
Starting delay/voltage rise < 0.1 s/< 50 ms < 0.1 s/< 50 ms
Rated current Iout rated 20 A 40 A
Current range
• Up to +45 °C 0 to 20 A 0 to 40 A 1)
• Up to +60 °C 0 to 20 A 0 to 40 A 1)
Dyn. V/I with
• Starting on short circuit Approx. 23 A constant current Approx. 46 A constant current
• Short-circuit in operation typ. 60 A for 25 ms typ. 120 A for 25 ms
Parallel connection for increased
output Yes, 2 (selectable current
characteristic) Yes, 2 (selectable current
characteristic)
Siemens KT10.1 · 2004 6/3
SITOP power · Standard 24 V
Single-phase and two-phase
Output currents 20 A and 40 A
6
The proven type The two-phase version
Continued on page 6/5.
1) Only permissible with ambient temperature from 0 to 45 °C.
2) Only permissible with ambient temperature from 0 to 50 °C.
The tried and tested power
supply unit with selectable in-
put voltage range for supply-
ing all standard applications
in automation engineering.
The power supply unit with
2-phase wide-range input for
widely changing power sup-
ply networks (> 550 V) as well
as industrial networks in
Canada and the USA.
20 A 20 A
6EP1 336-2BA00 6EP1 536-2AA00
Single-phase AC Two-phase AC
120/230 V AC
Settable using wire jumper 500 to 600 V 2 AC
wide-range input
93 to 132/187 to 264 V AC 420 to 682 V 2 AC
2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
> 10 ms at Vin = 93/187 V 6/30 ms at Vin = 420/600 V
50/60 Hz, 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
8.0/3.3 A 1.82 A (at 420 V)
< 81 A typ. 25 A
< 8 A2s < 1.0 A2s
T 10 A (not accessible) none
Circuit-breaker from 16 A
Characteristic C Required: 2-pole coupled cir-
cuit-breaker Char. C max. 10 A
or motor circuit-breaker
3RV1021-1DA10, setting 3 A
Stabilized, floating direct voltage Stabilized, floating direct voltage
24 V DC 24 V DC
±3% ±3%
< 150 mVpp < 150 mVpp
< 240 mVpp < 240 mVpp
22.8 to 26.4 V 1) 22.8 to 28.8 V 2)
Green LED for 24 V O.K. Green LED for 24 V O.K.
No overshoot of Vout
(soft start) Small overshoot of Vout (< 2 V for
max. 500 ms)
< 3 s/typ. 80 ms -
20 A 20 A
0 to 20 A 0 to 20 A
0 to 20 A (55 °C) 0 to 20 A
Approx. 20 A constant current Approx. 25 A constant current
Approx. 20 A constant current Approx. 28 A constant current
Yes, 2 1) Yes, 2 2)
Siemens KT10.1 · 2004
6/4
SITOP power · Standard 24 V
Output currents 20 A and 40 A
Single-phase and two-phase
6
Power supply, type 20 A 40 A
Order No. 6EP1 336-3BA00 6EP1 337-3BA00
Efficiency
Efficiency at Vout rated, Iout rated Approx. 89 % Approx. 88 %
Power loss at Vout rated, Iout rated Approx. 59 W Approx. 131 W
Control
Dyn. mains compensation
(Vin rated ±15%) < 1 % Vout < 1 % Vout
Dyn. load compensation
(Iout: 50/100/50 %) Approx. ± 2 % Vout Approx. ± 2 % Vout
Settling time
• Load step from 50 to 100 % < 5 ms (typ. 2 ms) < 5 ms (typ. 2 ms)
• Load step from 100 to 50 % < 5 ms (typ. 2 ms) < 5 ms (typ. 2 ms)
Protection and monitoring
Output overvoltage protection < 35 V < 35 V
Current limitation typ. 23 A typ. 46 A
Short-circuit protection Choice of stabilized current
characteristic approx. 23 A or
latching shutdown
Choice of stabilized current
characteristic approx. 46 A or
latching shutdown
RMS sustained short-circuit current Approx. 23 A Approx. 46 A
Overload/short-circuit indicator Yellow LED for "overload", red
LED for "latching shutdown" Yellow LED for "overload", red
LED for "latching shutdown"
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Protective class Class I Class I
Discharge current < 3.5 mA (typ. 0.4 mA) < 3.5 mA (typ. 0.4 mA)
TÜV test Yes Yes
CE marking Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259
FM approval - -
Appr. for use in marine vessels - -
Degree of protection (EN 60529) IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation EN 61000-3-2 -
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L, N, PE One screw-type terminal each
for 0.2 to 4 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.2 to 4 mm2 single-
core/finely stranded
• Output L+ 2 screw-type terminals for
0.5 to 4 mm22 screw-type terminals for
0.5 to 10 mm2
• Output M 2 screw-type terminals for
0.5 to 4 mm22 screw-type terminals for
0.5 to 10 mm2
Dimensions (W x H x D) in mm 160 x 125 x 125 240 x 125 x 125
Weight approx. 2.2 kg 2.9 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories Buffer module (6EP1961-3BA00)
Signalling module (6EP1961-
3BA10)
Redundancy module (6EP1961-
3BA20)
Buffer module (6EP1961-3BA00)
Signalling module (6EP1961-
3BA10)
Redundancy module (6EP1961-
3BA20)
Siemens KT10.1 · 2004 6/5
SITOP power · Standard 24 V
Single-phase and two-phase
Output currents 20 A and 40 A
6
20 A 20 A
6EP1 336-2BA00 6EP1 536-2AA00
Approx. 87 % Approx. 89 %
Approx. 72 W Approx. 60 W
Approx. ± 0.3 % Vout < 1 % Vout
±1 % V
out -4 %, +2 % Vout
Vout not outside tolerance < 3 ms
Vout not outside tolerance < 3 ms
Yes, acc. to EN 60950 Yes, acc. to EN 60950
typ. 22 A typ. 21 to 26 A
Stabilized current characteristic
down to 0 V Stabilized current characteristic
approx. 28 A
< 22 A Approx. 28 A
- -
Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Class I Class I
< 3.5 mA < 0.78 mA (550 V/60 Hz)
Yes Yes
Yes Yes
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E143289, CSA (CSA 22.2
No. 14-95)
--
--
IP20 IP20
EN 55022 Class B EN 55011 Class A
EN 61000-3-2 -
EN 61000-6-2 EN 61000-6-2
0 to +55 °C with natural
convection 0 to +60 °C with natural
convection
-25 to +85 °C -25 to +85 °C
Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
1 screw-type terminal for
0.33 to 10 mm21 screw-type terminal for
0.33 to 10 mm2
2 screw-type terminals for
0.33 to 10 mm22 screw-type terminals for
0.33 to 10 mm2
280 x 125 x 92 280 x 180 x 92
2.4 kg 3.3 kg
Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Mounting bracket 90°
(6EP1971-2BA00) Mounting bracket 90°
(6EP1971-2BA00)
Siemens KT10.1 · 2004
6/6
SITOP power · Standard 24 V
Notes
Single-phase and two-phase
6
Siemens KT10.1 · 2004
7
Output currents 5 A to 40 A
7/2 SITOP modular
7/2 75 A and 10 A
7/3 720 A and 40 A
7/6 The proven types
7/6 710 A and 20 A
7/7 730 A and 40 A
SITOP power · Standard 24 V
Three-phase
Siemens KT10.1 · 2004
7/2
SITOP power · Standard 24 V
Output currents 5 A to 40 A
Three-phase
7
■
Overview SITOP modular SITOP modular
■
Application
■
Technical specifications
Continued on page 7/4.
The modular power supply units with wide-range input for two-
phase connection to three-phase power supply networks; for
global use in many different fields of application; expansion of
functions possible using add-on modules.
Power supply, type 5 A 10 A
Order No. 6EP1 333-3BA00 6EP1 334-3BA00
Input Two-phase AC Two-phase AC
Rated voltage Vin rated 120/230 to 500 V AC
Settable via selector switch on
device
120/230 to 500 V AC
Settable via selector switch on
device
Voltage range 85 to 132/176 to 550 V AC 85 to 132/176 to 550 V AC
Overvoltage strength 1300 Vpeak, 1.3 ms 1300 Vpeak, 1.3 ms
Mains buffering at Iout rated > 25 ms at Vin = 120/230 V > 25 ms at Vin = 120/230 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 2.2/1.2 to 0.61 A 4.4/2.4 to 1.1 A
Inrush current limitation (+25 °C) < 35 A < 35 A
I2t < 1.7 A2s< 4.0 A
2s
Integrated line-side fuse T 3, 15 A T 6.3 A
Required fuse protection in mains
supply line Circuit-breaker 6 A (10 A) Char-
acteristic C (B), 2-pole coupled,
or motor circuit-breaker
3RV1021-...
Circuit-breaker 6 A (10 A) Char-
acteristic C (B), 2-pole coupled,
or motor circuit-breaker
3RV1021-...
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Total tolerance ± 3 % ± 3 %
• Stat. mains compensation Approx. 0.1 % Approx. 0.1 %
• Stat. load compensation Approx. 0.1 % Approx. 0.1 %
Residual ripple (clock frequency:
approx. 50 kHz) < 50 mVpp (typ. 10 mVpp)< 50 mVpp (typ. 10 mVpp)
Spikes (bandwidth: 20 MHz) < 200 mVpp (typ. 20 mVpp)< 200 mVpp (typ. 20 mVpp)
Setting range 24 to 28.8 V (max. 120 W) 24 to 28.8 V (max. 240 W)
Status display Green LED for 24 V O.K. Green LED for 24 V O.K.
Power ON/OFF behavior Overshoot of Vout approx. 3 % Overshoot of Vout approx. 3 %
Starting delay/voltage rise < 1 s/< 50 ms < 1 s/< 50 ms
Rated current Iout rated 5 A 10 A
Current range
• Up to +45 °C 0 to 5 A 0 to 10 A
• Up to +60 °C 0 to 5 A 0 to 10 A
Dyn. V/I with
• Starting on short circuit Approx. 5.5 A constant current Approx. 12 A constant current
• Short-circuit in operation typ. 15 A for 25 ms typ. 30 A for 25 ms
Parallel connection for increased
output Yes, 2 (selectable current
characteristic) Yes, 2 (selectable current
characteristic)
Siemens KT10.1 · 2004 7/3
SITOP power · Standard 24 V
Three-phase
Output currents 5 A to 40 A
7
SITOP modular SITOP modular
Continued on page 7/5.
The modular power supply units with three-phase wide-range
input for global use in many different fields of application;
expansion of functions possible using add-on modules.
20 A 40 A
6EP1 436-3BA00 6EP1 437-3BA00
Three-phase AC Three-phase AC
400 to 500 V 3 AC
wide-range input 400 to 500 V 3 AC
wide-range input
320 to 550 V
(startup from Vin > 340) 320 to 550 V
(startup from Vin > 340)
2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
> 6 ms at Vin = 400 V > 6 ms at Vin = 400 V
50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
1.1 A (Vin = 400 V) 2.2 A (Vin = 400 V)
< 35 A < 70 A
< 0.7 A2s < 2.8 A2s
None None
3-pole coupled circuit-breaker
6 to 16 A Char. C or motor
circuit-breaker 3RV1021-1DA10,
setting 3 A
3-pole coupled circuit-breaker
10 to 16 A Char. C or motor
circuit-breaker 3RV1021-1DA10,
setting 3 A
Stabilized, floating direct voltage Stabilized, floating direct voltage
24 V DC 24 V DC
± 3 % ± 3 %
Approx. ± 0.1 % Approx. ± 0.1 %
Approx. ± 0.2 % Approx. ± 0.2 %
< 100 mVpp < 100 mVpp
< 200 mVpp < 200 mVpp
24 to 28.8 V (max. 480 W) 24 to 28.8 V (max. 960 W)
Green LED for 24 V O.K. Green LED for 24 V O.K.
No overshoot of Vout (soft start) No overshoot of Vout (soft start)
< 2.5 s/< 500 ms < 2.5 s/< 500 ms
20 A 40 A
0 to 20 A 0 to 40 A
0 to 20 A 0 to 40 A
Approx. 23 A constant current Approx. 46 A constant current
typ. 60 A for 25 ms typ. 120 A for 25 ms
Yes, 2 (selectable current
characteristic) Yes, 2 (selectable current
characteristic)
Siemens KT10.1 · 2004
7/4
SITOP power · Standard 24 V
Output currents 5 A to 40 A
Three-phase
7
Power supply, type 5 A 10 A
Order No. 6EP1 333-3BA00 6EP1 334-3BA00
Efficiency
Efficiency at Vout rated, Iout rated Approx. 87 % Approx. 87 %
Power loss at Vout rated, Iout rated Approx. 18 W Approx. 36 W
Control
Dyn. mains compensation
(Vin rated ±15%) Approx. 0.1 % Approx. 0.1 %
Dyn. load compensation
(Iout: 50/100/50 %) Approx. +3 % Vout Approx. +3% Vout
Settling time
• Load step from 50 to 100 % < 5 ms (typ. 2 ms) < 5 ms (typ. 2 ms)
• Load step from 100 to 50 % < 5 ms (typ. 2 ms) < 5 ms (typ. 2 ms)
Protection and monitoring
Output overvoltage protection < 35 V < 35 V
Current limitation typ. 5.5 A typ. 12 A
Short-circuit protection Choice of stabilized current
characteristic approx. 5.5 A or
latching shutdown
Choice of stabilized current
characteristic approx. 12 A or
latching shutdown
RMS sustained short-circuit current Approx. 5.5 A Approx. 12 A
Overload/short-circuit indicator Yellow LED for "overload", red
LED for "latching shutdown" Yellow LED for "overload", red
LED for "latching shutdown"
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Protective class Class I Class I
Discharge current < 3.5 mA (typ. 0.25 mA) < 3.5 mA (typ. 0.32 mA)
TÜV test Yes Yes
CE marking Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E197259
FM approval - -
Appr. for use in marine vessels - -
Degree of protection (EN 60529) IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation EN 61000-3-2 EN 61000-3-2
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L1, L2, L3, PE One screw-type terminal each
for 0.2 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.2 to 2.5 mm2 single-
core/finely stranded
• Output L+ 2 screw-type terminals for
0.2 to 2.5 mm22 screw-type terminals for
0.2 to 2.5 mm2
• Output M 2 screw-type terminals for
0.2 to 2.5 mm22 screw-type terminals for
0.2 to 2.5 mm2
Dimensions (W x H x D) in mm 70 x 125 x 125 90 x 125 x 125
Weight approx. 1.2 kg 1.4 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories Buffer module (6EP1961-3BA00)
Signalling module
(6EP1961-3BA10)
Redundancy module
(6EP1961-3BA20)
Buffer module (6EP1961-3BA00)
Signalling module
(6EP1961-3BA10)
Redundancy module
(6EP1961-3BA20)
Siemens KT10.1 · 2004 7/5
SITOP power · Standard 24 V
Three-phase
Output currents 5 A to 40 A
7
20 A 40 A
6EP1 436-3BA00 6EP1 437-3BA00
Approx. 90 % Approx. 90 %
Approx. 53 W Approx. 106 W
< 1 % Vout < 1 % Vout
Approx. ± 2 % Vout Approx. ± 2 % Vout
< 10 ms (typ. 4 ms) < 10 ms (typ. 4 ms)
< 10 ms (typ. 4 ms) < 10 ms (typ. 4 ms)
< 35 V < 35 V
typ. 23 A typ. 46 A
Choice of stabilized current
characteristic approx. 23 A or
latching shutdown
Choice of stabilized current
characteristic approx. 46 A or
latching shutdown
Approx. 23 A Approx. 46 A
Yellow LED for "overload", red
LED for "latching shutdown" Yellow LED for "overload", red
LED for "latching shutdown"
Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Class I Class I
< 3.5 mA < 3.5 mA
Yes Yes
Yes Yes
Yes, UL listed (UL 508)
File E197259, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E197259, CSA (CSA 22.2
No. 14-95)
--
--
IP20 IP20
EN 55022 Class B EN 55022 Class B
EN 61000-3-2 EN 61000-3-2
EN 61000-6-2 EN 61000-6-2
0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
-25 to +85 °C -25 to +85 °C
Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
One screw-type terminal each
for 0.2 to 4 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.2 to 4 mm2 single-
core/finely stranded
2 screw-type terminals for
0.33 to 4 mm22 screw-type terminals for
0.33 to 10 mm2
2 screw-type terminals for
0.33 to 4 mm22 screw-type terminals for
0.33 to 10 mm2
160 x 125 x 125 240 x 125 x 125
2 kg 3.2 kg
Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Buffer module (6EP1961-3BA00)
Signalling module
(6EP1961-3BA10)
Redundancy module
(6EP1961-3BA20)
Buffer module (6EP1961-3BA00)
Signalling module
(6EP1961-3BA10)
Redundancy module
(6EP1961-3BA20)
Siemens KT10.1 · 2004
7/6
SITOP power · Standard 24 V
Output currents 10 A to 40 A
Three-phase
7
■
Overview The proven types
■
Application
■
Technical specifications
Continued on page 7/8.
1) Only permissible with ambient temperature from 0 °C to 45 °C.
The tried and tested power supply units with three-phase wide-
range input for supplying all standard applications in automation
engineering.
Power supply, type 10 A 20 A
Order No. 6EP1 434-2BA00 6EP1 436-2BA00
Input Three-phase AC Three-phase AC
Rated voltage Vin rated 400 to 500 V 3 AC
wide-range input 400 to 500 V 3 AC
wide-range input
Voltage range 360 to 550 V 3 AC (340 to 360 V
for max. 2 s or at max.
0.9 x Iout rated)
360 to 550 V 3 AC (340 to 360 V
for max. 2 s or at max.
0.9 x Iout rated)
Overvoltage strength 2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 6 ms at Vin = 360 V > 3 ms at Vin = 360 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 0.65 A (at 400 V) 1.2 A (at 400 V)
Inrush current limitation (+25 °C) < 25 A < 25 A
I2t < 1.0 A2s< 1.0 A
2s
Integrated line-side fuse none none
Required fuse protection in mains
supply line 3-pole coupled circuit-breaker
Char. C up to 25 A (recommen-
dation: 6 A) or motor circuit-
breaker 3RV1021-1DA10,
setting 3 A
3-pole coupled circuit-breaker
Char. C up to 25 A (recommen-
dation: 6 A) or motor circuit-
breaker 3RV1021-1DA10,
setting 3 A
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Total tolerance ± 3 % ± 3 %
• Stat. mains compensation
• Stat. load compensation
Residual ripple (clock frequency:
approx. 50 kHz) < 150 mVpp (typ. 60 mVpp) < 150 mVpp (typ. 60 mVpp)
Spikes (bandwidth: 20 MHz) < 240 mVpp (typ. 120 mVpp)< 240 mVpp (typ. 120 mVpp)
Setting range 22.8 to 26.4 V 1) 22.8 to 26.4 V 1)
Status display Green LED for 24 V O.K. Green LED for 24 V O.K.
Power ON/OFF behavior No overshoot of Vout (soft start) No overshoot of Vout (soft start)
Starting delay/voltage rise < 3 s/typ. 40 ms < 3 s/typ. 40 ms
Rated current Iout rated 10 A 20 A
Current range
• Up to +45 °C 0 to 10 A 0 to 20 A
• Up to +55 °C 0 to 10 A 0 to 20 A
Dyn. V/I with
• Starting on short circuit Constant current approx. 18 A Constant current approx. 30 A
• Short-circuit in operation Constant current approx. 18 A Constant current approx. 30 A
Parallel connection for increased
output Yes, 2 1) Yes, 2 1)
Siemens KT10.1 · 2004 7/7
SITOP power · Standard 24 V
Three-phase
Output currents 10 A to 40 A
7
The proven types
Continued on page 7/9.
The tried and tested power supply units with three-phase wide-
range input for supplying all standard applications in automation
engineering.
30 A 40 A
6EP1 437-2BA00 6EP1 437-2BA10
Three-phase AC Three-phase AC
400 to 500 V 3 AC
wide-range input 400 to 500 V 3 AC
wide-range input
360 to 550 V 3 AC (340 to 360 V
for max. 2 s or at max.
0.9 x Iout rated)
360 to 550 V 3 AC (340 to 360 V
for max. 2 s or at max.
0.9 x Iout rated)
2.3 x Vin rated, 1.3 ms 2.3 x Vin rated, 1.3 ms
> 4.5 ms at Vin = 360 V > 3 ms at Vin = 360 V
50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
1.4 A (at 400 V) 1.9 A (at 400 V)
< 25 A < 25 A
< 1.0 A2s < 1.0 A2s
none none
3-pole coupled circuit-breaker
Char. C up to 25 A (recommen-
dation: 6 A) or motor circuit-
breaker 3RV1021-1DA10,
setting 3 A
3-pole coupled circuit-breaker
Char. C up to 25 A (recommen-
dation: 6 A) or motor circuit-
breaker 3RV1021-1DA10,
setting 3 A
Stabilized, floating direct voltage Stabilized, floating direct voltage
24 V DC 24 V DC
± 3 % ± 3 %
< 150 mVpp (typ. 50 mVpp)< 150 mVpp (typ. 50 mVpp)
< 240 mVpp (typ. 200 mVpp)< 240 mVpp (typ. 200 mVpp)
22.8 to 26.4 V 1) 22.8 to 26.4 V 1)
Green LED for 24 V O.K. Green LED for 24 V O.K.
Small overshoot of Vout (< 2 V for
max. 500 ms) Small overshoot of Vout (< 2 V for
max. 500 ms)
< 3 ms/typ. 40 ms < 3 ms/typ. 40 ms
30 A 40 A
0 to 30 A 0 to 40 A
0 to 30 A 0 to 40 A
Approx. 60 A for 600 ms Approx. 70 A for 600 ms
Approx. 60 A for 600 ms Approx. 70 A for 600 ms
Yes, 2 1) Yes, 2 1)
Siemens KT10.1 · 2004
7/8
SITOP power · Standard 24 V
Output currents 10 A to 40 A
Three-phase
7
Power supply, type 10 A 20 A
Order No. 6EP1 434-2BA00 6EP1 436-2BA00
Efficiency
Efficiency at Vout rated, Iout rated Approx. 89 % Approx. 89 %
Power loss at Vout rated, Iout rated Approx. 30 W Approx. 59 W
Control
Dyn. mains compensation
(Vin rated ± 15 %) < 1 % Vout < 1 % Vout
Dyn. load compensation
(Iout: 50/100/50 %) ± 2 % Vout ± 2 % Vout
Settling time
• Load step from 50 to 100 % < 2 ms < 2 ms
• Load step from 100 to 50 % < 2 ms < 2 ms
Protection and monitoring
Output overvoltage protection Yes, acc. to EN 60950 Yes, acc. to EN 60950
Current limitation typ. 10.5 to 13 A typ. 21 to 26 A
Short-circuit protection Stabilized current characteristic
down to 0 V Stabilized current characteristic
down to 0 V
RMS sustained short-circuit current < 20 A < 30 A
Overload/short-circuit indicator - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I
Discharge current < 0.35 mA (550 V/60 Hz) < 0.35 mA (550 V/60 Hz)
TÜV test Yes; CB scheme Yes; CB scheme
CE marking Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289
FM approval - -
Appr. for use in marine vessels - -
Degree of protection (EN 60529) IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation EN 61000-3-2 EN 61000-3-2
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +55 °C with natural
convection 0 to +55 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L1, L2, L3, PE One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
• Output L+ 1 screw-type terminal for
0.33 to 10 mm21 screw-type terminal for
0.33 to 10 mm2
• Output M 2 screw-type terminals for
0.33 to 10 mm22 screw-type terminals for
0.33 to 10 mm2
Dimensions (W x H x D) in mm 280 x 125 x 92 280 x 125 x 92
Weight approx. 2 kg 2 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories Mounting bracket 90°
(6EP1971-2BA00) Mounting bracket 90°
(6EP1971-2BA00)
Siemens KT10.1 · 2004 7/9
SITOP power · Standard 24 V
Three-phase
Output currents 10 A to 40 A
7
30 A 40 A
6EP1 437-2BA00 6EP1 437-2BA10
Approx. 90 % Approx. 90 %
Approx. 80 W Approx. 107 W
< 1 % Vout < 1 % Vout
-4 %, +2 % Vout -4 %, +2 % Vout
< 3 ms < 3 ms
< 3 ms < 3 ms
Yes, acc. to EN 60950 Yes, acc. to EN 60950
typ. 31.5 to 39 A typ. 42 to 52 A
Electronic shutdown, automatic
restart Electronic shutdown, automatic
restart
< 48 A < 62 A
- -
Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Class I Class I
< 0.78 mA (550 V/60 Hz) < 0.78 mA (550 V/60 Hz)
Yes; CB scheme Yes; CB scheme
Yes Yes
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289
--
--
IP20 IP20
EN 55022 Class B EN 55022 Class B
EN 61000-3-2 EN 61000-3-2
EN 61000-6-2 EN 61000-6-2
0 to +55 °C with natural
convection 0 to +55 °C with natural
convection
-25 to +85 °C -25 to +85 °C
Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
1 screw-type terminal for
0.33 to 10 mm21 screw-type terminal for
0.33 to 10 mm2
2 screw-type terminals for
0.33 to 10 mm22 screw-type terminals for
0.33 to 10 mm2
280 x 180 x 92 280 x 180 x 92
3.6 kg 3.6 kg
Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Mounting bracket 90°
(6EP1971-2BA00) Mounting bracket 90°
(6EP1971-2BA00)
Siemens KT10.1 · 2004
7/10
SITOP power · Standard 24 V
Notes
Three-phase
7
Siemens KT10.1 · 2004
8
8/2 SITOP modular signalling module
8/2 SITOP modular buffer module
8/2 SITOP modular redundancy
module
8/4 SITOP select diagnosis module
8/6 Mounting bracket 90°
8/7 Mounting adapter for S7 rail and
PS-CPU connecting comb
8/7 IP65 connector seals
8/7 Circular input connectors and
AS-Interface coupling module PG
SITOP power · Standard 24 V
Additional components
Siemens KT10.1 · 2004
8/2
SITOP power · Standard 24 V
Additional components
8
■
Overview SITOP modular SITOP modular SITOP modular
signalling module buffer module redundancy module
■
Application
■
Technical specifications
Using the signalling module in
combination with a stabilized
SITOP modular power supply
unit, signals can be provided
on the operating status of the
power supply unit, and remote
switching ON/OFF of the unit
is possible; automatic con-
tacting with the power supply
unit.
With brief interruptions in the
power supply, the buffer mod-
ule in combination with a sta-
bilized SITOP modular power
supply unit can buffer the load
current without an interrup-
tion. The buffer module is
wired in parallel with the out-
put of the power supply unit.
The redundancy module
serves to decouple two stabi-
lized SITOP modular power
supplies in parallel mode. If
one power supply fails, the
24 V is safely retained.
Order No. 6EP1 961-3BA10 6EP1 961-3BA00 6EP1 961-3BA20
Input/output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated input voltage Vin rated -24 V DC 24 V DC
Input voltage range -24 to 28.8 V DC 24 to 28.8 V DC
Control input Non-isolated input for remote
ON/OFF switching of the power
supply unit
--
Rated output voltage Vout rated -V
in – approx. 1 V Vin – approx. 0.5 V
Rated current Iout rated - 40 A 20 A (maximum total current
40 A)
Mains buffering -100 ms at 40 A up to 800 ms at
5 A load current -
Buffer time, max. -3 s -
Parallel connection for increased
output -Yes, 2 -
Protection and monitoring
Static current limitation - typ. 40 A -
Short-circuit protection - Electronic -
Displays/messages
Status display -Green LED for supply voltage
> 20.5 V Green LED for "Power supply 1
and Power supply 2 OK"
Signals Floating relay contacts
(changeover contacts, rating
6 A/240 V AC) for "Output volt-
age OK" and "Power supply
availability OK"
-Floating relay contact
(changeover contact, rating
6 A/240 V AC) for "Power supply
1 and Power supply 2 OK",
switching threshold adjustable
from 20 to 25 V
Siemens KT10.1 · 2004 8/3
SITOP power · Standard 24 V
Additional components
8
■
Technical specifications (continued)
Order No. 6EP1 961-3BA10 6EP1 961-3BA00 6EP1 961-3BA20
Safety
Galvanic isolation Yes, SELV acc. to EN 60950
(relay contacts) Yes, SELV acc. to EN 60950 Yes, SELV acc. to EN 60950
(relay contact)
Protective class Class I Class I Class I
TÜV test Yes Yes Yes
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, UL listed (UL 508)
File E197259, CSA (CSA 22.2
No. 14-95)
Yes, UL listed (UL 508)
File E197259, CSA (CSA 22.2
No. 14-95)
Yes, cULus listed (UL 508,
CSA 22.2 No. 14-M91)
FM approval - - -
Appr. for use in marine vessels - - -
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B EN 55022 Class B
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection 0 to +60 °C with natural
convection
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections Screw-type terminals for
0.14 to 2.5 mm2
single-core/finely stranded
One screw-type terminal each
for + and - for 0.5 to 10 mm2
single-core/finely stranded
Input, output and ground: one
screw-type terminal each for
0.33 to 10 mm2, single-
core/finely stranded;
relay contact: one screw-type
terminal each for 0.5 to 2.5 mm2,
single-core/finely stranded
Dimensions (W x H x D) in mm 26 x 125 x 116 70 x 125 x 125 70 x 125 x 125
Weight approx. 0.15 kg 1.2 kg 1.0 kg
Mounting Can be directly snapped onto
the side of the basic unit Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Siemens KT10.1 · 2004
8/4
SITOP power · Standard 24 V
Additional components
8
■
Overview SITOP select
■
Application
■
Technical specifications
The diagnosis module is used together with 24 V power supply units to divide the load current be-
tween several branch circuits and to monitor the individual currents. Faults in the individual circuits
resulting from an overload or short-circuit are detected and switched off selectively, and other load
current paths therefore remain unaffected by the fault. This results in rapid fault diagnostics, and
downtimes are minimized.
Type Module 4 x 10 A
Order No. 6EP1 961-2BA00
Input DC voltage
Rated voltage Vin rated 24 V DC
Voltage range 22 to 30 V
Overvoltage strength 35 V; 100 ms
Output DC voltage
Rated voltage Vout rated Vout - 0.5 V
Total tolerance/
residual ripple Corresponding to the input voltage
Number of output channels 4
Rated current
Iout rated up to +60 °C 10 A per channel
Setting range 2 to 10 A per channel
Parallel connection of several
channels Not permissible
Efficiency
Efficiency at Vout rated, Iout rated Approx. 97 %
Power loss at Vout rated, Iout rated Approx. 30 W
Switch-off characteristic per
channel
Overcurrent Iout = 1.0 to 1.3 x set value, switch-off after approx. 5 s
Current limitation Iout = 1.35 x set value, switch-off after approx. 50 to 100 ms
Immediate switch-off Iout > set value and Vin < 20 V
Reset Using keys on module
Protection and monitoring
Line protection Electronic; additionally possible via accessible FK2 blade-type fuse (equipped when delivered with 15 A
fuse) per channel
Status displays Two-color LED per channel, green for output switched through, red for output switched off
Signaling contact Common signal contact (NO contact)
Safety
Protective class Class III
Degree of protection (EN 60529) IP20
TÜV test Yes
CE marking Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA 22.2 No. 14-M91), File E197259;
cURus recognized (UL 60950, CSA 22.2 No. 60950), File E151273
EMC
Interference emission EN 55022 Class B
Interference immunity EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural convection
Transportation and storage
temperature range -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to EN 60721, no condensation
Siemens KT10.1 · 2004 8/5
SITOP power · Standard 24 V
Additional components
8
■
Technical specifications (continued)
■
Characteristic curves
Switch-off characteristic
■
Schematics
Basic circuit
Type Module 4 x 10 A
Order No. 6EP1 961-2BA00
Mechanical specifications
Connections
• Input +24 2 screw-type terminals for 0.33 to 10 mm2
• Input 0 V 2 screw-type terminals for 0.22 to 4 mm2
• Outputs 1 to 4 1 screw-type terminal per channel for 0.22 to 4 mm2
• Signalling contact 2 screw-type terminals for 0.22 to 4 mm2
Dimensions (W x H x D) in mm 72 x 90 x 90
Weight 0.4 kg
Mounting Snap-mounting on DIN rail EN 50022-35x15/7.5
s
0 20 40 60 80 100 120 140%
Load current
Release time
100.0
10.0
1.0
0.1
0.0
5.0 s
0.10 s
rated
G
_
KT01
_
en
_
00062
ñ
=
~
24 V
SITOP
select
Reset
+
+ 24 V
13 14
0 V
1234
Load 1 Load 3 Load 4
Floating
signalling
contact
Power supply, e.g. SITOP power
Control logics
Load 2
G_KT01_EN_00063a
Siemens KT10.1 · 2004
8/6
SITOP power · Standard 24 V
Additional components
8
■
Overview Mounting bracket
■
Application
■
Technical specifications
Combination of a SITOP power supply unit with a 90° mounting
bracket results in a minimum surface requirement on the rear
panel of the switchgear cabinet (the width of the power supply
unit becomes the depth, the depth becomes the width). The
mounting bracket is suitable for switchgear cabinets with a
depth of 240 mm or 320 mm or more.
Mounting bracket For depth 240 mm For depth 320 mm
Order No. 6EP1 971-1AA01 6EP1 971-2BA00
Dimensions (W x H x D) in mm 50 x 159 x 236 100 x 150 x 320
Sheet plate thickness 2 mm 1.5 mm
Connected mounting rail DIN rail EN 50022-35x7.5 DIN rail EN 50022-35x15
Weight approx. 0.9 kg 0.9 kg
Mounting Can be screwed on level surface
(keyhole mounting with M5
screws, drill hole distance
147.5 mm height)
Can be screwed on level surface
(keyhole mounting with M6
screws, drill hole distance
90 mm height, 50 mm to the
side)
Supplied accessories Two M5 combi screws and two
M5 self-tapping screws Four M6 combi screws
Suitable for SITOP 24 V/3.5 A
(6EP1 332-1SH31)
SITOP 24 V/5 A
(6EP1 333-1AL12)
SITOP 24 V/10 A
(6EP1 334-1AL12)
SITOP DC UPS module 40 A
(6EP1 931-2FC01)
SITOP 24 V/10 A
(6EP1 434-2BA00)
SITOP 24 V/20 A
(6EP1 336-2BA00,
6EP1 335-3BA00,
6EP1 436-2BA00,
6EP1 436-3BA00,
6EP1 457-3BA00,
6EP1 536-2AA00)
SITOP 24 V/30 A
(6EP1 437-2BA00)
SITOP 24 V/40 A
(6EP1 437-2BA10,
6EP1 337-3BA00,
6EP1 437-3BA00)
Siemens KT10.1 · 2004 8/7
SITOP power · Standard 24 V
Additional components
8
■
Mounting adapter for S7 rail and PS-CPU connecting comb
The single-phase SITOP power supply units 24 V/2 A (6ES7 307-1BA00-0AA0, 6ES7 305-1BA80-0AA0 ), 24 V/5 A (6ES7 307-1EA00-
0AA0, 6ES7 307-1EA80-0AA0) and 24 V/10 A (6ES7 307-1KA01-0AA0) are special mechanical versions for SIMATIC S7-300.
They can be mounted on an S7 rail, and the connection to the new CPUs or the compact CPUs of the S7-300 can be established
without problem using a supplied connecting comb.
Power supply units of same design without connecting comb, but with a supplied mounting adapter for DIN rail EN 50022-35x15,
are available with the Order Nos. 6EP1 331-1SL11 (24 V/2 A), 6EP1 333-1SL11 (24 V/5 A) and 6EP1 334-1SL12 (24 V/10 A).
A connecting comb for older CPUs with product phase-out since 2003 as well as the mounting adapter are available as individual
accessories.
■
Selection and Ordering Data
■
IP65 connector seals
The single-phase SITOP power supply unit 24 V/10 A in IP65 degree of protection (6EP1 334-2CA00) has a design and functionality
which are optimally adapted to the ET 200X distributed I/O system.
Thanks to integral plug-in connectors, it can be flush-mounted with the modules without any special wiring overhead.
If the power supply unit is operated outside the ET 200X system as a stand-alone power supply unit in IP65 degree of protection,
connector seals are required to seal the integral plug-in connectors.
■
Selection and Ordering Data
■
Circular input connectors and AS interface coupling module PG
A 6-pole circular connector with socket inset is required for the ASi power supply 30 V/2.4 A in IP65 degree of protection
(6EP1 632-1AL01) for connection of the input side.
The connection of the ASi power supply to the ASi network is made using the coupling module PG.
■
Selection and Ordering Data
PS-CPU connecting comb
(spare part for CPUs 313, 314,
315, 315/316/318-2 DP, IM153)
6ES7 390-7BA00-0AA0
Mounting adapter for DIN rail
EN 50022-35x15 6ES7 390-6BA00-0AA0
IP65 connector seal
for power supply unit
6EP1 334-2CA00
6EP1 971-2CA00
6-pole circular input connector
with socket inset 6ES5 760-2CA11
AS interface coupling module
PG
3RG9 220-0AA00
Siemens KT10.1 · 2004
8/8
SITOP power · Standard 24 V
Notes
Additional components
8
Siemens KT10.1 · 2004
9
DC UPS
9/2 Overview
9/2 DC UPS software
9/3 DC UPS module 6 A and 15 A
9/11 DC UPS module 40 A
9/14 Battery module 1.2 Ah
9/15 Battery module 2.5 Ah
9/16 Battery module 3.2 Ah
9/17 Battery module 7 Ah
9/18 Battery module 12 Ah
SITOP power · Standard 24 V
Uninterruptible
power supplies
Siemens KT10.1 · 2004
9/2
SITOP power · Standard 24 V
DC UPS
Uninterruptible power supplies
9
■
Overview
By combining a DC UPS module with at least one 24 V battery
module and a SITOP power supply unit, longer power failures
can be bridged without any interruption.
This combination is used, for example, in machine tool manufac-
ture, in the textile industry, with all types of production lines and
filling systems, and in conjunction with 24 V industrial PCs. The
negative effects which frequently result from power failures can
thus be prevented.
For nonstop use in the event of power failures, Siemens offers
the uninterruptible power supplies
• DC UPS 6 A
• DC UPS 15 A
• DC UPS 40 A
as well as the battery modules
• 1.2 Ah
• 3.2 Ah
•7 Ah
•12 Ah
• 2.5 Ah (high-temperature battery).
■
Selection table for battery modules with power failure buffer times
Note:
• The power failure buffer times are based on the discharge pe-
riod of the completely charged battery module down to a bat-
tery voltage of 21 V; ambient temperature 25 °C.
• With the DC UPS 40 A module, high electronically limited peak
currents (120 A for approx. 12 ms, up to 40 A for several min-
utes depending on the battery capacity) are automatically de-
livered in the event of increased load current requirements
(e.g. when switching on incandescent lamps, contactors with
DC autotransformer winding, DC motors, DC/DC converters,
electronic modules with high input capacitance). To achieve
this, at least two battery modules of 7 Ah or more must be con-
nected in parallel.
• Following a power failure, the battery module is automatically
disconnected from the loads electronically and rapidly re-
charged at 0.2/0.4 A (DC UPS 6 A module), at 0.35/0.7 A
(DC UPS 15 A module) or at 2 A (DC UPS 40 A module) (V/I
characteristic with 27 V or 27.3 V end-of-charge voltage).
■
DC UPS software
The DC UPS 6 A and 15 A modules are optionally available with
a serial interface or USB interface. All relevant messages con-
cerning the status of the DC UPS can then be sent to a PC (e.g.
SIMATIC PC). The SITOP DC UPS software, with which the sig-
nals sent from the DC UPS module can be processed further on
the PC, is very easy to use. In monitoring mode, the statuses of
the DC UPS module are visualized on the PC. The safe shutdown
in the event of a power failure and the automatic restart of the PC
are supported. It is also possible to freely define the responses
to the various operating states of the DC UPS module, permitting
extremely flexible incorporation into many different applications.
The software executes under the WinNT 4.0, Win2000 and
WinXP operating systems. It is available as freeware on the
SITOP Internet site for free downloading.
Monitoring and configuration windows of the SITOP UPS software
Load current Battery module 1.2 Ah
(6EP1935-6MC01)
Battery module 3.2 Ah
(6EP1935-6MD11)
Battery module 7 Ah
(6EP1935-6ME21)
Battery module 12 Ah
(6EP1935-6MF01)
Battery module 2.5 Ah
(6EP1935-6MD31)
1 A 30 min 2.5 h 6 h 10 h 2 h
2 A 11 min 45 min 2.5 h 4 h 45 min
4 A 2 min 20 min 45 min 2.5 h 20 min
6 A 1 min 10 min 30 min 1 h 13 min
8 A - 4 min 20 min 40 min 9 min
10 A - 1.5 min 15 min 30 min 7 min
12 A - 1 min 10 min 25 min 5.5 min
14 A - 50 s 8 min 20 min 4.5 min
16 A - 40 s 6 min 15 min 4 min
20 A - - 2 min 11 min -
Siemens KT10.1 · 2004 9/3
SITOP power · Standard 24 V
Uninterruptible power supplies
DC UPS module 6 A and 15 A
9
■
Overview
• Compact design, only 50 mm wide
• Simple DIN rail mounting
• Absolutely interruption-free buffering of power failures through
immediately electronic connection of the batteries as soon as
the DC UPS input voltage drops below the value set using DIP
switches
• High safety and availability through monitoring of operational
readiness, battery supply line, battery aging (message "Battery
replacement necessary") and battery charge (message "Bat-
tery charge >85%")
• Support of automatic restart of industrial PCs through select-
able switch-off response
• Optionally with serial or USB interface.
SW tool as download at
http://www.siemens.de/sitop
executes under WinNT4.0, Win2000 and WinXP.
■
Integration
}
}
}
=
Load
DC UPS Module
DC UPS active
24 V DC
Mains or buffer mode
Mains,
AC or
3 AC
24 V DC
Buffer readiness or
alarm/prewarning switching-off of battery
and need of battery replacement
SITOP Power Supply
parallel
switching
Battery module
G_KT01_EN_00214
Battery charge >85 %
Optionally serial interface or USB
interface for above signals
Siemens KT10.1 · 2004
9/4
SITOP power · Standard 24 V
DC UPS module 6 A and 15 A
Uninterruptible power supplies
9
1
X3.1-9
L+ X1.1
M X1.2
Input V
in
24 V DC
DC
DC
X1.7 +Bat
27-
18.5 V DC
X1.8 -Bat
X1.3 L+
X1.5 L+
X1.4 M
X1.6 M
output
V
out
X2.1
X2.3
X2.2
X2.4
X2.6
X2.5
X2.7
X2.8
X2.9
X2.10 M
+320 s
+160 s
+ 80 s
+ 40 s
+ 20 s
+ 10 s
o.k.
Bat
Ba>85%
Bat
24 V DC o.k.
Alarm
SITOP
optional USB
for 6EP1931-2DC41
and 6EP1931-2EC41
serial
interface
only 6EP1931-2DC31
and 6EP1931-2EC31
power
supply
battery
DC UPS module 6
DC UPS module 15
power section
load
charging current *
1
set time/max. time
interruption V
out
green yellow greenred
control
operating elements
*1: charging current 0.2 A or 0.4 A for 6EP1931-2DC../0.35 A or 0.7 A for 6EP1931-2EC..
alarm
readiness
charge <85%
operating state battery
On/Off
operating state battery
On/Off
buffering time
+5 s fixed
end-of-charge
voltage
+26.3 V fixed
connection threshold
+22 V fixed
G_KT01_EN_00226
+2 V
+1 V
+0.5 V
+1 V
+0.5 V
+0.2 V
+0.1 V
+0.2 V
Siemens KT10.1 · 2004 9/5
SITOP power · Standard 24 V
Uninterruptible power supplies
DC UPS module 6 A and 15 A
9
■
Function
The following timing diagrams show the characteristic of the input and output voltages at the terminals of the DC UPS module as well
as the signal characteristic of the signals (relays) and the remote signal (interface) as examples.
"Long" power failure with DC UPS without serial or USB
interface (Fig. 9/1)
Power recovery only following expiry of buffer time tp
(t3 after t4):
If the input voltage at the DC UPS module fails (time t1), the bat-
tery "Bat" immediately takes over the DC supply, and the output
voltage Vout is therefore retained completely without interruption.
The floating changeover contact "OK/Bat" switches to its deen-
ergized position "Bat".
At the time t1, the buffer time tp set on the DIP switches is started
automatically.
The fact that the DIP switch is set to "Interruption output Vout" has
no effect in this example because the input voltage returns at
time t3 only after the set buffer time (time t4) has expired.
"Short" power failure with DC UPS without serial or USB
interface (Fig. 9/2)
Power recovery prior to expiry of buffer time tp
(t3 before t4):
If the input voltage at the DC UPS module fails (time t1), the bat-
tery "Bat" immediately takes over the DC supply, and the output
voltage Vout is therefore retained completely without interruption.
The floating changeover contact "OK/Bat" switches to its deen-
ergized position "Bat".
At the time t1, the buffer time tp set on the DIP switches is started
automatically.
With the selected DIP switch position "Interruption output Vout",
the output voltage Vout is automatically interrupted for 5 seconds
following expiry of the set buffer time tp (time t4).
The battery has already been disconnected because the input
voltage has returned at the time t3.
If the DIP switch is not set to "Interruption output Vout", there is no
interruption in this example because the input voltage has al-
ready returned at time t3 prior to expiry of the set buffer time
(time t4).
Buffer time (time t4) automatically interrupted for 5 s, and battery
disconnected from the output at the same time which had not yet
been disconnected because the input voltage was missing.
Fig. 9/1 "Long power failure" Fig. 9/2 "Short power failure"
DC UPS without serial or USB interface (6EP1931-2DC21/ -2EC21)
DIP switch settings on device: buffer time tp (from 5 to 635 s with bottom row No. 2 to 7)/
/t = following setting (with bottom row No. 1 to left)/ = with setting interruption Vout
(with bottom row No. 8 to left)
Legend:
t1 t3t4
(t4 - t1 = tp)
ok
Bat
V
in
V
out
ok
Bat
t1 t3 t4 t5
(t4 - t1 = tp) (t5 - t4 = 5 s)
V
in
V
out
Vin: input voltage at terminals X1.1 – X1.2
Vout: output voltage at terminals X1.3 – X1.4 and X1.5 - X1.6
ok: Signal for input voltage Vin OK or above the set battery con-
nection threshold
Bat: Signal for battery mode (batteries connected to the output,
batteries supply the load)
Remote: Signal for remote timer start with signal level = 0 at pin 7 of the
9-pin serial interface (pin 7 is normally the positive power
supply of the interface)
t1: Input voltage Vin missing or falls below the set connection
threshold
t2: Buffer time set on the DIP switches is started by a remote
timer start (signal level = 0)
t3: Input voltage Vin is above the set connection threshold
t4: End of set buffer time (output is switched off and/or battery
disconnected)
t5: Output is connected again 5 sec. after switch-off
tp: Buffer time set on the DIP switches (bottom row No. 2 to 7)
Siemens KT10.1 · 2004
9/6
SITOP power · Standard 24 V
DC UPS module 6 A and 15 A
Uninterruptible power supplies
9
■
Function (continued)
"Long" power failure with DC UPS with serial or USB
interface (Fig. 9/3)
Power recovery only following expiry of buffer time tp
(t3 after t4):
If the input voltage at the DC UPS module fails (time t1), the bat-
tery "Bat" immediately takes over the DC supply, and the output
voltage Vout is therefore retained completely without interruption.
The floating changeover contact "OK/Bat" switches to its deen-
ergized position "Bat".
At the user-selectable time t2, the buffer time tp set on the DIP
switches is started by means of the signal "Remote timer start"
(signal level = 0 at pin 7 of the 9-pin serial interface).
The fact that the DIP switch is set to "Interruption output Vout" has
no effect in this example because the input voltage returns at
time t3 after the set buffer time (time t4) has expired.
Note: Without a remote signal level = 0 with the set duration t =
max., there is no interruption in the output voltage here because
the set buffer time is not started (or only interrupted if the exhaus-
tive discharge protection disconnects the battery and the input
voltage has not returned by then).
"Short" power failure with DC UPS with serial or USB inter-
face (Fig. 9/4)
Power recovery prior to expiry of buffer time tp
(t3 before t4):
If the input voltage at the DC UPS module fails (time t1), the bat-
tery "Bat" immediately takes over the DC supply, and the output
voltage Vout is therefore retained completely without interruption.
The floating changeover contact "OK/Bat" switches to its deen-
ergized position "Bat".
At the user-selectable time t2, the buffer time tp set on the DIP
switches is started by means of the signal "Remote timer start"
(signal level = 0 at pin 7 of the 9-pin serial interface following
previous signal timing according to Instruction Manual).
With the selected DIP switch position "Interruption output Vout",
the output voltage Vout is automatically interrupted for 5 seconds
following expiry of the set buffer time tp (time t4).
The battery has already been disconnected because the input
voltage has returned at the time t3.
The output voltage interruption of Vout for 5 s permits an auto-
matic restart for many industrial PCs, even if the mains voltage
(or the input voltage Vin on the DC UPS module) returns during
shutting-down of the PC, as in this example.
Note: Without a remote signal level = 0 with setting t = max. du-
ration, there is no interruption in the output voltage here because
the set buffer time is not started.
Fig. 9/3 "Long power failure" Fig. 9/4 "Short power failure"
DC UPS with serial or USB interface (6EP1931-2DC31/-2DC41/-2EC31/-2EC41)
DIP switch settings on device: buffer time tp (from 5 to 635 s with bottom row No. 2 to 7)/
/t = max. time (with bottom row No. 1 to right)/interruption Vout (with bottom row No. 8 to left)
Legend:
ok
Bat
Remote
t1 t2 t3t4
(t4 - t2 = tp)
Vin
Vout
ok
Bat
Remote
t1 t2 t3 t4 t5
(t4 - t2 = tp) (t5 - t4 = 5 s)
V
in
V
out
Vin: input voltage at terminals X1.1 – X1.2
Vout: output voltage at terminals X1.3 – X1.4 and X1.5 - X1.6
ok: Signal for input voltage Vin OK or above the set battery con-
nection threshold
Bat: Signal for battery mode (batteries connected to the output,
batteries supply the load)
Remote: Signal for remote timer start with signal level = 0 at pin 7 of the
9-pin serial interface (pin 7 is normally the positive power
supply of the interface)
t1: Input voltage Vin missing or falls below the set connection
threshold
t2: Buffer time set on the DIP switches is started by a remote
timer start (signal level = 0)
t3: Input voltage Vin is above the set connection threshold
t4: End of set buffer time (output is switched off and/or battery
disconnected)
t5: Output is connected again 5 sec. after switch-off
tp: Buffer time set on the DIP switches (bottom row No. 2 to 7)
Siemens KT10.1 · 2004 9/7
SITOP power · Standard 24 V
Uninterruptible power supplies
DC UPS module 6 A
9
■
Technical specifications
1) All SITOP 24 V DC power supply units are permissible without limitation.
DC UPS module 6
Order No. 6EP1 931-2DC21
6EP1 931-2DC31 (with serial interface)
6EP1 931-2DC41 (with USB interface)
Input L+/ M with normal mode Stabilized direct voltage
Rated voltage Vin rated1) 24 V DC
Voltage range 22 to 29 V DC
Connection threshold for battery 22.5 V DC ± 0.1 V (default setting),
adjustable in range from 22 to 25.5 V DC (in intervals of 0.5 V)
Rated current Iin rated 6 A + approx. 0.6 A with empty battery
Mains buffering
Mains buffering or buffer time dependent on connected battery and load current:
• With 3.2 Ah battery module (6EP1935-6MD11) at +25 °C: approx. 10 min at 6 A; 20 min at 4 A;
45 min at 2 A
• With 7 Ah battery module (6EP1935-6ME21) at +25 °C: approx. 30 min at 6 A; 45 min at 4 A;
150 min at 2 A
On/off control circuit External floating NO contact required (load max. 15 V DC/max. 10 mA).
With the control circuit open, the battery is disconnected from the output L+, and the mains buffering is
therefore canceled.
Buffer time Adjustable using DIP switches to maximum buffer time until forced switch-off by exhaustive discharge
protection (at approx. 19 V) or to timed buffering from 5 to 635 seconds
(in intervals of 10 s)
Output L+/ M with normal mode
Rated voltage Vout rated 24 V DC (output voltage of SITOP power supply unit)
Voltage range Input voltage Vin less approx. 0.5 V DC
Output current Iout 0 to 6 A
Dynamic current with overload Electronic current limitation to 1.05 to 1.4 x Iout rated for approx. 80 ms, then electronic switching-off of
output with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Dynamic current with short-circuit Electronic current limitation to 1.5 to 3 x Iout rated for approx. 20 ms, then electronic switching-off of output
with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Output L+/ M with battery mode
Rated voltage Vout rated 24 V DC (from battery module)
Voltage range, approx. 27 to 19 V DC;
27 V at no load, 25 V at Iout = 0.05 x C x 1/h or 24 V at Iout = 1 x C x 1/h or 23 V at Iout = 2 x C x 1/h
(C = total connected battery capacity in Ah), 19 V switch-off threshold for exhaustive discharge protection
Output current Iout 0 to 6 A (permanently reliable)
Dynamic current with overload Electronic current limitation to 1.05 to 1.4 x Iout rated for approx. 80 ms, then electronic switching-off of
output with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Dynamic current with short-circuit Electronic current limitation to 1.5 to 3 x Iout rated for approx. 20 ms, then electronic switching-off of output
with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Output +Bat / -Bat with normal mode I-V charging characteristic
(first constant current I, then constant voltage V)
End-of-charge voltage V 27.0 V DC ± 0.1 V (default setting),
adjustable in range from 26.3 to 29.3 V (in intervals of 0.1 V)
Charging current I Approx. 0.4 A (default setting), adjustable to 0.2 A or 0.4 A
(charging is carried out with the on/off circuit closed or open)
Efficiency / power loss
At Vout rated, Iout rated approx. 95 %/7 W
With battery operation, approx. 94.5 %/8 W
Protection and monitoring
Polarity reversal protection Against input voltage and batteries with reversed polarity
Overload protection Electronic current limitation to 1.05 to 1.4 x Iout rated for approx. 80 ms, then electronic switching-off of
output with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Short-circuit protection Electronic current limitation to 1.5 to 3 x Iout rated for approx. 20 ms, then electronic switching-off of output
with automatic attempts at restarting (approx. 20 s interval between the restart attempts).
Internal, non-accessible 16 A fuse
Exhaustive discharge protection Automatic switch-off at battery voltage below approx. 19 V
Monitoring "Wire breakage, battery circuit" Alarm signal if battery circuit is not closed or if it opens during operation (cyclic test approx. every 20 s)
Monitoring "Battery replacement
necessary" Alarm signal flashing at approx. 0.25 Hz (approx. 2 s alarm, approx. 2 s no alarm, approx. 2 s alarm etc.).
Check every 4 hours if no buffer mode or switch-off has taken place within 4 hours
Monitoring "Battery charge > 85 %" Indication whether batteries are charged to at least 85 % of the rated capacity
Siemens KT10.1 · 2004
9/8
SITOP power · Standard 24 V
DC UPS module 6 A
Uninterruptible power supplies
9
■
Technical specifications (continued)
1) Permissible contact rating: 60 V DC/1 A or 30 V AC/1 A. 2) "24 V DC OK" means: Voltage of power supply unit is greater than the
battery connection threshold set on the DC UPS module 6.
DC UPS module 6
Order No. 6EP1 931-2DC21
6EP1 931-2DC31 (with serial interface)
6EP1 931-2DC41 (with USB interface)
Signalling 1)
Normal mode Green LED (OK) and floating changeover contact "24 V DC OK/Bat" to position "24 V DC OK" 2)
Buffer or battery mode (battery supplies
load on its own, or in addition to PS in
event of overload)
Yellow LED (Bat) and floating changeover contact "24 V DC OK/Bat" to position "Bat" (= de-energized
position)
Alarm (buffer readiness missing or pre-
warning at < 20.4 V battery voltage) Red LED (Alarm) and floating changeover contact to position "Alarm" (= de-energized position).
Causes for absence of buffer readiness during normal mode could be: Operating status Off or open on/off
control circuit, battery module not connected, battery faulty or with reversed polarity (battery voltage
< 18.5 V) or wire breakage between battery and UPS module. Scanning and thus updating of the signal
every 20 s.
Causes for absence of buffer readiness during buffer mode could be: Battery voltage has fallen below
20.4 V DC (= prewarning prior to switching-off by exhaustive discharge protection) as well as switching-
off of battery because of overload, short-circuit, exhaustive discharge protection or expired buffer time.
The Red LED then goes off.
"Battery replacement necessary" Red LED (Alarm) flashes at 0.25 Hz and floating changeover contact (Alarm) switches at approx. 0.25 Hz
"Battery charge > 85 %" Green LED (Bat > 85 %) and floating NO contact closed (de-energized position = open)
Optional interface and software
Serial interface Only with 6EP1 931-2DC31
Output of all signals, and receipt of signal "Remote timer start".
Techn. design: PC-compatible. 8N1 send and receive, 9600 baud, 8 data bits, 1 stop bit, no parity bit.
Required connection to PC: 1 : 1 continuous 9-pole SUB D extension cable (male/female),
only pin 2 (RXD), pin 3 (TDX) and pin 7 (RTS) are required.
USB interface Only with 6EP1 931-2DC41
Output of all signals, and receipt of signal "Remote timer start".
Techn. design: Specification 2.0 with full speed, i.e. 2 Mbit/s. Powered by DC UPS with +5 V
("self powered").
Required connection to PC: Commercially available 4-core shielded cable, 90 Ohm, max. 5 m,
USB series "A" connector to PC and USB series "B" connector to DC UPS
Software A software tool (executes under WinNT4.0, Win 2000 and WinXP) for reading and processing the signals
is available on the Internet at http://www.siemens.de/sitop
as a download. Further information on the interface can also be found there.
Control signals
On/off control signal By opening the control circuit (or using DIP switch on device), the buffer mode is terminated, or the
battery is disconnected from the output. All other functions are retained.
"Remote timer start" via serial interface or
USB Starts the mains buffering for the set buffer time
Safety
Galvanic isolation primary/secondary No
Protective class Class III (ext. circuit and power supply unit: SELV voltage acc. to EN 60950 is required)
EMC
Interference emission RI suppression acc. to EN 55022, limit characteristic B
Interference immunity Interference immunity acc. to EN 61000-6-2
Ambient conditions
Ambient temperature during operation 0 to +60 °C with natural convection
Transportation and storage temperature -40 to +70 °C
Degree of protection (EN 60529) IP20
Humidity rating Conditions of use acc. to EN 60721, climatic class 3K3 (relative humidity 5 % to 85 % and absolute
humidity 1 g/m³ to 25 g/m³; no condensation)
Approvals
CE CE conformity acc. to 98/336 EEC and 73/23 EEC
UL / cUL UL 508 / CSA C22.2, File E197259
Mechanical specifications
Connections for 24 V DC input 2 screw-type terminals for 1 to 4 mm²/17 to 11 AWG
Connections for 24 V DC output 4 screw-type terminals for 1 to 4 mm²/17 to 11 AWG
Connections for 24 V DC battery module 2 screw-type terminals for 1 to 4 mm²/17 to 11 AWG
Connections for control circuit and signals 10 screw-type terminals for 0.5 to 2.5 mm²/20 to 13 AWG
Dimensions (W x H x D) in mm 50 x 125 x approx. 125
Required clearance 50 mm above and 50 mm below the device
Weight Approx. 0.4 kg (with serial or USB interface: approx. 0.45 kg)
Mounting Snap-mounting on DIN rail EN 50022-35x15/7.5
Siemens KT10.1 · 2004 9/9
SITOP power · Standard 24 V
Uninterruptible power supplies
DC UPS module 15 A
9
■
Technical specifications
1) All SITOP 24 V DC power supply units are permissible without limitation.
DC UPS module 15
Order No. 6EP1 931-2EC21
6EP1 931-2EC31 (with serial interface)
6EP1 931-2EC41 (with USB interface)
Input L+/ M with normal mode Stabilized direct voltage
Rated voltage Vin rated 1) 24 V DC
Voltage range 22 to 29 V DC
Connection threshold for battery 22.5 V DC ± 0.1 V (default setting), adjustable in range from 22 to 25.5 V DC (in intervals of 0.5 V)
Rated current Iin rated 15 A + approx. 1 A with empty battery
Mains buffering
Mains buffering or buffer time Dependent on connected battery and load current:
• With 3.2 Ah battery module (6EP1935-6MD11) at +25 °C:
approx. 45 s at 15 A; 1.5 min at 10 A; 13 min at 5 A
• With 7 Ah battery module (6EP1935-6ME21) at +25 °C:
approx. 7 min at 15 A; 15 min at 10 A; 38 min at 5 A
On/off control circuit External floating NO contact required (load max. 15 V DC/max. 10 mA).
With the control circuit open, the battery is disconnected from the output L+, and the mains buffering is
therefore canceled.
Buffer time Adjustable using DIP switches to maximum buffer time until forced switch-off by exhaustive discharge
protection (at approx. 19 V) or to timed buffering from 5 to 635 seconds (in intervals of 10 s)
Output L+/ M with normal mode
Rated voltage Vout rated 24 V DC (output voltage of SITOP power supply unit)
Voltage range Input voltage Vin less approx. 0.5 V DC
Output current Iout 0 to 15 A
Dynamic current with overload Electronic current limitation to 1.05 to 1.4 x Iout rated for approx. 80 ms, then electronic switching-off of
output with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Dynamic current with short-circuit Electronic current limitation to 1.5 to 3 x Iout rated for approx. 20 ms, then electronic switching-off of output
with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Output L+/ M with battery mode
Rated voltage Vout rated 24 V DC (from battery module)
Voltage range, approx. 27 to 19 V DC;
27 V at no load, 25 V at Iout = 0.05 x C x 1/h or 24 V at Iout = 1 x C x 1/h or 23 V at Iout = 2 x C x 1/h
(C = total connected battery capacity in Ah), 19 V switch-off threshold for exhaustive discharge protection
Output current Iout 0 to 15 A (permanently reliable)
Dynamic current with overload Electronic current limitation to 1.05 to 1.4 x Iout rated for approx. 80 ms, then electronic switching-off of
output with automatic attempt at restarting (approx. 20 s interval between the restart attempts)
Dynamic current with short-circuit Electronic current limitation to 1.5 to 3 x Iout rated for approx. 20 ms, then electronic switching-off of output
with automatic attempt at restarting (approx. 20 s interval between the restart attempts)
Output +Bat / -Bat with normal mode I-V charging characteristic (first constant current I, then constant voltage V)
End-of-charge voltage V 27.0 V DC ± 0.1 V (default setting), adjustable in range from 26.3 to 29.3 V (in intervals of 0.1 V)
Charging current I Approx. 0.7 A (default setting), adjustable to 0.35 A or 0.7 A (charging is carried out with the on/off
circuit closed or open)
Efficiency / power loss
At Vout rated, Iout rated approx. 96.2 %/14 W
With battery operation, approx. 96 %/15 W
Protection and monitoring
Polarity reversal protection Against input voltage and batteries with reversed polarity
Overload protection Electronic current limitation to 1.05 to 1.4 x Iout rated for approx. 80 ms, then electronic switching-off of
output with automatic attempts at restarting (approx. 20 s interval between the restart attempts)
Short-circuit protection Electronic current limitation to 1.5 to 3 x Iout rated for approx. 20 ms, then electronic switching-off of output
with automatic attempts at restarting (approx. 20 s interval between the restart attempts).
Internal, non-accessible 16 A fuse
Exhaustive discharge protection Automatic switch-off at battery voltage below approx. 19 V
Monitoring "Wire breakage, battery circuit" Alarm signal if battery circuit is not closed or if it opens during operation (cyclic test approx. every 20 s)
Monitoring "Battery replacement
necessary" Alarm signal flashing at approx. 0.25 Hz (approx. 2 s alarm, approx. 2 s no alarm, approx. 2 s alarm etc.).
Check every 4 hours if no buffer mode or switch-off has taken place within 4 hours
Monitoring "Battery charge > 85 %" Signal whether batteries are charged to at least 85 % of the rated capacity
Siemens KT10.1 · 2004
9/10
SITOP power · Standard 24 V
DC UPS module 15 A
Uninterruptible power supplies
9
■
Technical specifications (continued)
1) Permissible contact rating: 60 V DC/1 A or 30 V AC/1 A. 2) "24 V DC OK" means: Voltage of power supply unit is greater than the
battery connection threshold set on the DC UPS module 15.
DC UPS module 15
Order No. 6EP1 931-2EC21
6EP1 931-2EC31 (with serial interface)
6EP1 931-2EC41 (with USB interface)
Signalling 1)
Normal mode Green LED (OK) and floating changeover contact "24 V DC OK/Bat" to position "24 V DC OK" 2)
Buffer or battery mode (battery supplies
load on its own, or in addition to PS in
event of overload)
Yellow LED (Bat) and floating changeover contact "24 V DC OK/Bat" to position "Bat" (= de-energized
position)
Alarm (buffer readiness missing or pre-
warning at < 20.4 V battery voltage) Red LED (Alarm) and floating changeover contact to position "Alarm" (= de-energized position).
Causes for absence of buffer readiness during normal mode could be: Operating status Off or open on/off
control circuit, battery module not connected, battery faulty or with reversed polarity (battery voltage
< 18.5 V) or wire breakage between battery and UPS module. Scanning and thus updating of the signal
every 20 s.
Causes for absence of buffer readiness during buffer mode could be: Battery voltage fallen below
20.4 V DC (= prewarning prior to switching-off by exhaustive discharge protection) as well as switching-
off of battery because of overload, short-circuit, exhaustive discharge protection or expired buffer time.
The Red LED then goes off.
"Battery replacement necessary" Red LED (Alarm) flashes at 0.25 Hz and floating changeover contact (Alarm) switches at approx. 0.25 Hz
"Battery charge > 85 %" Green LED (Bat > 85 %) and floating NO contact closed (de-energized position = open)
Optional interface and software
Serial interface Only with 6EP1 931-2EC31
Output of all signals, and receipt of signal "Remote timer start".
Techn. design: PC-compatible. 8N1 send and receive, 9600 baud, 8 data bits, 1 stop bit, no parity bit.
Required connection to PC: 1 : 1 continuous 9-pole SUB D extension cable (male/female),
only pin 2 (RXD), pin 3 (TDX) and pin 7 (RTS) are required.
USB interface Only with 6EP1 931-2EC41
Output of all signals, and receipt of signal "Remote timer start". Techn. design: Specification 2.0 with full
speed, i.e. 2 Mbit/s. Powered by DC UPS with +5 V ("self powered").
Required connection to PC: Commercially available 4-core shielded cable, 90 Ohm, max. 5 m, USB series
"A" connector to PC and USB series "B" connector to DC UPS
Software A software tool (executes under WinNT4.0, Win 2000 and WinXP) for reading and processing the signals
is available on the Internet at
http://www.siemens.de/sitop
as a download. Further information on the interface can also be found there.
Control signals
On/off control signal By opening the control circuit (or using DIP switch on the device), buffer mode is terminated, or the
battery is disconnected from the output. All other functions are retained.
"Remote timer start" via serial interface or
USB Starts the mains buffering for the set buffer time
Safety
Galvanic isolation primary/secondary No
Protective class Class III (ext. circuit and power supply unit: SELV voltage acc. to EN 60950 is required)
EMC
Interference emission RI suppression acc. to EN 55022, limit characteristic B
Interference immunity Interference immunity acc. to EN 61000-6-2
Ambient conditions
Ambient temperature during operation 0 to +60 °C with natural convection
Transportation and storage temperature -40 to +70 °C
Degree of protection (EN 60529) IP20
Humidity rating Conditions of use acc. to EN 60721, climatic class 3K3 (relative humidity 5 % to 85 % and absolute
humidity 1 g/m³ to 25 g/m³; no condensation)
Approvals
CE CE conformity acc. to 98/336 EEC and 73/23 EEC
UL / cUL UL 508 / CSA C22.2, File E197259
Mechanical specifications
Connections for 24 V DC input 2 screw-type terminals for 1 to 4 mm²/17 to 11 AWG
Connections for 24 V DC output 4 screw-type terminals for 1 to 4 mm²/17 to 11 AWG
Connections for 24 V DC battery module 2 screw-type terminals for 1 to 4 mm²/17 to 11 AWG
Connections for
control circuit and signals
10 screw-type terminals for 0.5 to 2.5 mm²/20 to 13 AWG
Dimensions (W x H x D) in mm 50 x 125 x approx. 125
Required clearance 50 mm above and 50 mm below the device
Weight Approx. 0.4 kg (with serial or USB interface: approx. 0.45 kg)
Mounting Snap-mounting on DIN rail EN 50022-35x15/7.5
Siemens KT10.1 · 2004 9/11
SITOP power · Standard 24 V
Uninterruptible power supplies
DC UPS module 40 A
9
■
Overview
• Mounting depth only approx. 65 mm
• Rated output power 480 W with one battery module, 960 W with
two battery modules
• Extremely high efficiency of approx. 99% as result of patented
circuit concept
• Immediate electronic connection of battery as soon as the con-
sumer voltage or the voltage present between the L+/M termi-
nals of the DC UPS module falls below a value of 22.5 V DC.
The consumer voltage only drops to 22 V DC for a maximum of
1 ms.
• High electronically limited peak currents (120 A for approx.
12 ms, up to 40 A for several minutes depending on the battery
capacity) are automatically delivered in the event of increased
load current requirements (e.g. when switching on incandes-
cent lamps, contactors with DC autotransformer winding,
DC motors, DC/DC converters, electronic modules with high
input capacitance). To achieve this, at least two battery mod-
ules of 7 Ah or more must be connected in parallel.
• Following a power failure, the battery module is automatically
disconnected from the consumers electronically and rapidly
recharged with a constant current of 2 A (V/I characteristic with
27.3 V end-of-charge voltage).
• Signalling
- Green LED/yellow LED and floating changeover contact for
mains/battery mode
- Red LED and floating changeover contact for buffer readi-
ness (LED off)/ alarm (LED on)
■
Integration
Block diagram: Configuration of uninterruptible SITOP power supply 40 A
SITOP power
24 V24 V
Mains Main switch Power supply DC UPS module Load
DC UPS module 40
10 to 40 A
Aux. contact
ON/OFF
Message: mains or
buffer mode
(floating changeover
contact)
Message: buffer
readiness
or alarm/prewarning
prior to switching-off
of battery
24 V battery module
3 AC
G_KT01_EN_00159
Siemens KT10.1 · 2004
9/12
SITOP power · Standard 24 V
DC UPS module 40 A
Uninterruptible power supplies
9
■
Integration (continued)
Block diagram
■
Characteristic curves
ON/OFF
M
M
V2U
L+
L+
DC
DC
US
M
L+
SITOP
power
V1
K1 V3
UBat
V4
F1
HSV
+BAT
-BAT
F2
K3
K2
G_KT01_en_00160
Load
Monitoring
Shield
ALARM
BATT
ALARM(rd)B(ye)N(gn)
N/B
Voltage characteristic between
the terminals L+/M of the DC
UPS module with connection of
1 battery module 24 V/7 Ah de-
pending on duration and load
current.
Parameters: Load current 20 A/
10 A/5 A/2.5 A/1.3 A;
2 battery modules 24 V/7 Ah
Parameters: Load current 40 A/
20 A/10 A/5 A/2.5 A
20A
10A
5A
40A
20A
10A 5A
0 1 2 4 6 8 10 20 40 1 2 4 6 8 10 20 40
min
voltage
L+/M in V
hours
G_KT01_EN_00161
2.5A 1.3A
2.5A
28.0
26.0
24.0
22.0
20.0
18.0
16.0
Siemens KT10.1 · 2004 9/13
SITOP power · Standard 24 V
Uninterruptible power supplies
DC UPS module 40 A
9
■
Technical specifications
1)
Reliable power supplies are the single-phase SITOP power 10 A and 20 A and
the three-phase SITOP power 10 A to 40 A if their output voltage is set between
25 V and 25.5 V DC. The single-phase SITOP power supply units 2 A to 10 A
with Order Nos. 6EP13..-1... are not reliable.
2) Permissible contact rating: 60 V DC/1 A or 30 V AC/1 A.
3) Approval only in combination with battery module 7 Ah (6EP1935-6ME01).
4) Both L+ and M connections are electrically connected within the device,
and a differentiation of the input/output connections on the device is there-
fore unnecessary.
DC UPS module 40
Order No. 6EP1 931-2FC01
Input L+/ M with normal mode Stabilized direct voltage
Rated voltage Vin rated 1) 24 V DC
Voltage range 23.5 to 26 V DC
Overvoltage strength VDE 0160 A1 (April 1989), limit curve B2 (2 x Vrated, 0.4 ms)
Connection threshold for battery Approx. 22.5 V
Mains buffering at Iout rated Dependent on connected battery, see discharge characteristic of battery module
Rated current Iin rated 40 A
On/off control circuit External floating NO contact required (load max. 12 V DC/max. 5 mA). With the control circuit open, the
battery is disconnected from the output L+, and the mains buffering is therefore canceled.
Output L+/ M with normal mode
Rated voltage Vout rated 24 V DC (output voltage of SITOP power supply unit)
Voltage range Input voltage less approx. 0.1 V
Output current Iout with discharged/
charged battery 0 to 37 A (max. 3 A required for battery charging)/0 to 40 A
Output L+/ M with battery mode
Rated voltage Vout rated 24 V DC (from battery module)
Voltage range, approx. 27 to 18.5 V DC; 27 V at no load, 25 V at Iout = 0.05 x C x 1/h or 24 V at Iout = 1 x C x 1/h or 23 V at
Iout = 2 x C x 1/h (C = total connected battery capacity in Ah), 18.5 V switch-off threshold for exhaustive
discharge protection
Output current Iout with a battery module
of 7 Ah or more 0 to 25 A
Output current Iout with two battery
modules of 7 Ah or more 0 to 40 A
Dyn. V/I with short-circuit Typ. 120 A for approx. 12 ms (with two battery modules of 7 Ah or more)
Output +Bat/-Bat with normal mode I-V charging characteristic (first constant current I, then constant voltage V)
End-of-charge voltage 27.3 V ± 0.3 V
Charging current 0 to 2.5 A (typ. 2 A); charging is carried out with the on/off circuit closed or open
Efficiency/power loss
at Vout rated, Iout rated and fully charged
battery Approx. 99 %/approx. 7 W
With battery operation Approx. 97 %/approx. 30 W
Protection and monitoring
Exhaustive discharge protection Automatic switch-off at battery voltage < 18.5 V
Short-circuit protection Temperature monitoring of circuit-breaker, electronic switch-off with automatic restart
Monitoring "Wire breakage, battery circuit" Alarm signal flashing at approx. 1/3 Hz if battery circuit is not closed or if it opens during operation
(cyclic test every 20 s)
Signalling
On/off (battery switch-off) External NO contact (load 12 V DC/5 mA)
Normal mode Green LED + N/B signal (floating changeover contact N/B in position N) 2)
Buffer or battery mode (battery supplies
load on its own, or in addition to PS in
event of overload)
Yellow LED + N/B signal (floating changeover contact N/B in position N) 2)
Alarm (buffer readiness missing or pre-
warning at < 20.4 V battery voltage) Red LED + alarm signal (floating changeover contact for alarm) 2)
Safety
Galvanic isolation primary/secondary No
Protective class Class III (ext. circuit and power supply unit: SELV voltage acc. to EN 60950 is required)
TÜV test/CE marking Yes/yes
UL/cUL (CSA) approval 3) Yes, UL/cUL recognized (UL 1950), File E172952
Degree of protection (EN 60529) IP20
EMC
Interference emission EN 55022 Class B
Interference immunity EN 61000-6-2
Ambient conditions
Ambient temperature range in operation 0 to +60 °C with natural convection
Transportation and storage temperature range
-25 to +85 °C
Humidity rating H acc. to DIN 40040: relative humidity up to 75 % as mean value, 95 % on 30 days/year, no condensation
Mechanical specifications
Input connections 4) L+, M 2 screw-type terminals for 0.5 to 10 mm2 single-core/finely stranded
Output connections 4) L+, M 2 screw-type terminals for 0.5 to 10 mm2 single-core/finely stranded
Battery connections +/- 2 screw-type terminals for 0.5 to 10 mm2 single-core/finely stranded
Signals On/Off, N/B, alarm, shield
connections 9 screw-type terminals for 0.5 to 2,5 mm2 single-core/finely stranded
Dimensions (W x H x D) in mm, approx. 220 x 130 x 65
Approx. weight 1.2 kg
Mounting Snap-mounting on DIN rail EN 50022-35x7.5 or on SITOP power 90° mounting bracket
Siemens KT10.1 · 2004
9/14
SITOP power · Standard 24 V
Battery module 1.2 Ah
Uninterruptible power supplies
9
■
Overview
• Battery module for DC UPS module 6 A
• Contains two maintenance-free, sealed lead-acid batteries
from the same batch fitted in a holder and connected in series
• Completely prewired with battery fuse holder and terminals
• Low self-discharge rate of approx. 3 % per month (at +20 °C)
1) For storage, installation and operation of the lead-acid batteries, the
appropriate DIN/VDE regulations or the country-specific directives (e.g.
VDE 0510 Part 2/EN 50272-2) must be observed. The battery location must
be sufficiently ventilated, potential ignition sources must be at least 50 cm
away.
■
Technical specifications
Battery module 1.2 Ah
Order No. 6EP1 935-6MC01
Battery type, charging current/
charging voltage
Maintenance-free lead-acid
batteries 1)
Recommended end-of-charge voltage (standby use)
• For +25 °C battery temperature 27.0 V DC
• For other battery temperatures 27.8 V for +10 °C;
27.3 V for +20 °C;
26.8 V for +30 °C;
26.7 V for +35 °C;
26.6 V for +40 °C
Recommended charging current Max. 0.3 A
Protection
Short-circuit protection Battery fuse 15 A/32 V
(FK2 flat fuse + holder)
Battery protection Valve control
Safety
Protective class Class III
UL/cUL (CSA) approval UL/cUL recognized (UL1778,
CSA 22.2 No. 107.1-95),
File E219627
Degree of protection (EN 60529) IP00
Operating specifications
Ambient temperature range +5 to +40 °C
Transportation and storage temper-
ature range -20 to +50 °C
Self-discharge rate Approx. 3 % per month at a
battery temperature of 20 °C
(increased value at higher tem-
perature)
Service life
The service life of the chemical lead-acid batteries (reduction to 50 % of
original capacity) depends on the battery temperature as follows:
At +20 °C Approx. 4 years
At +25 °C Approx. 3.5 years
At +30 °C Approx. 3 years
At +35 °C Approx. 2.5 years
At +40 °C Approx. 2 years
At +45 °C Approx. 1.5 years
At +50 °C Approx. 1 year
Mechanical specifications
Connection 1 terminal each for 0.08 to
2.5 mm2 for + BAT and - BAT
Supplied accessories Accessory pack with FK2 fuse
15 A
Dimensions (W x H x D) in mm Approx. 96 x 106 x 108
Weight Approx. 2 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 or keyhole
mounting for hanging in M4
screws
Siemens KT10.1 · 2004 9/15
SITOP power · Standard 24 V
Uninterruptible power supplies
Battery module 2.5 Ah
9
■
Overview
• High-temperature battery for DC UPS module 6 A and 15 A
• Contains two maintenance-free, sealed chemical lead-acid
batteries from the same batch fitted in a holder and connected
in series
• Completely prewired with battery fuse holder and terminals
• Low self-discharge rate of approx. 3 % per month (at +20 °C)
1) For storage, installation and operation of the lead-acid batteries, the
appropriate DIN/VDE regulations or the country-specific directives (e.g.
VDE 0510 Part 2/EN 50272-2) must be observed. The battery location must
be sufficiently ventilated, potential ignition sources must be at least 50 cm
away.
■
Technical specifications
Battery module 2.5 Ah
Order No. 6EP1 935-6MD31
Battery type, charging current/
charging voltage
Maintenance-free chemical
lead-acid batteries 1)
Recommended end-of-charge voltage (standby use)
• For +25 °C battery temperature 27.7 V DC
• For other battery temperatures 29.0 V for -10 °C;
28.6 V for 0 °C;
28.3 V for +10 °C;
27.9 V for +20 °C;
27.5 V for +30 °C;
27.2 V for +40 °C;
26.8 V for +50 °C;
26.4 V for +60 °C
Recommended charging current Max. 5 A
Protection
Short-circuit protection Battery fuse 15 A/32 V
(FK2 flat fuse + holder)
Battery protection Valve control
Safety
Protective class Class III
UL/cUL (CSA) approval UL/cUL recognized (UL1778,
CSA 22.2 No. 107.1-95),
File E219627
Degree of protection (EN 60529) IP00
Operating specifications
Ambient temperature range -40 to +60 °C with natural
convection
Transportation and storage temper-
ature range -40 to +60 °C
Self-discharge rate Approx. 3 % per month at a
battery temperature of 20 °C
(increased value at higher tem-
perature)
Service life
The service life of the chemical lead-acid batteries (reduction to 80 % of
original capacity) depends on the battery temperature as follows:
At +15 °C Approx. 19 years
At +20 °C Approx. 13 years
At +25 °C Approx. 9 years
At +30 °C Approx. 7 years
At +35 °C Approx. 5 years
At +40 °C Approx. 3 years
At +45 °C Approx. 2 years
At +50 °C Approx. 1.5 years
At +60 °C Approx. 1 year
Mechanical specifications
Connection 1 terminal each for 0.08 to
2.5 mm2 for + BAT and - BAT
Supplied accessories Accessory pack with FK2 fuse
15 A
Dimensions (W x H x D) in mm Approx. 265 x 151 x 91
Weight Approx. 3.8 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 or keyhole
mounting for hanging in M4
screws
Siemens KT10.1 · 2004
9/16
SITOP power · Standard 24 V
Battery module 3.2 Ah
Uninterruptible power supplies
9
■
Overview
• Battery module for DC UPS module 6 A and 15 A
• Contains two maintenance-free, sealed lead-acid batteries
from the same batch fitted in a holder and connected in series
• Includes battery fuse holder and terminals
• Low self-discharge rate of approx. 3 % per month (at +20 °C)
1) For storage, installation and operation of the lead-acid batteries, the
appropriate DIN/VDE regulations or the country-specific directives (e.g.
VDE 0510 Part 2/EN 50272-2) must be observed. The battery location must
be sufficiently ventilated, potential ignition sources must be at least 50 cm
away.
■
Technical specifications
Battery module 3.2 Ah
Order No. 6EP1 935-6MD11
Battery type, charging current/
charging voltage
Maintenance-free, sealed lead-
acid batteries 1)
Recommended end-of-charge voltage (standby use)
• For +25 °C battery temperature 27.0 V DC
• For other battery temperatures 27.8 V for +10 °C;
27.3 V for +20 °C;
26.8 V for +30 °C;
26.7 V for +35 °C;
26.6 V for +40 °C
Recommended charging current Max. 0.8 A
Protection
Short-circuit protection Battery fuse 15 A/32 V
(FK2 flat fuse + holder)
Battery protection Valve control
Safety
Protective class Class III
UL/cUL (CSA) approval UL/cUL recognized (UL1778,
CSA 22.2 No. 107.1-95),
File E219627
Degree of protection (EN 60529) IP00
Operating specifications
Ambient temperature range +5 to +40 °C with natural
convection
Transportation and storage temper-
ature range -20 to +50 °C
Self-discharge rate Approx. 3 % per month at a
battery temperature of 20 °C
(increased value at higher tem-
perature)
Service life
The service life of the chemical lead-acid batteries (reduction to 50 % of
original capacity) depends on the battery temperature as follows:
At +20 °C Approx. 4 years
At +25 °C Approx. 3.5 years
At +30 °C Approx. 3 years
At +35 °C Approx. 2.5 years
At +40 °C Approx. 2 years
At +45 °C Approx. 1.5 years
At +50 °C Approx. 1 year
Mechanical specifications
Connection 1 terminal each for 0.08 to
2.5 mm2 for + BAT and - BAT
Supplied accessories Accessory pack with FK2 fuse
15 A
Dimensions (W x H x D) in mm Approx. 190 x 151 x approx. 82
Weight Approx. 3.2 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 or keyhole
mounting for hanging in M4
screws
Siemens KT10.1 · 2004 9/17
SITOP power · Standard 24 V
Uninterruptible power supplies
Battery module 7 Ah
9
■
Overview
• Battery for DC UPS module 6 A and 15 A and DC UPS module
40 A
• Contains two maintenance-free, sealed lead-acid batteries
from the same batch fitted in a holder and connected in series
• Completely prewired with battery fuse holder and terminals
• Accessory pack with FK2 spare fuses 15 A and 20 A
• Low self-discharge rate of approx. 3 % per month (at +20 °C)
1) For storage, installation and operation of the lead-acid batteries, the
appropriate DIN/VDE regulations or the country-specific directives (e.g.
VDE 0510 Part 2/EN 50272-2) must be observed.The battery location must
be sufficiently ventilated, potential ignition sources must be at least 50 cm
away.
■
Technical specifications
Battery module 7 Ah
Order No. 6EP1 935-6ME21
Battery type, charging current/
charging voltage
Maintenance-free, sealed lead-
acid batteries 1)
Recommended end-of-charge voltage (standby use)
• For +25 °C battery temperature 27.0 V DC
• For other battery temperatures 27.8 V for +10 °C;
27.3 V for +20 °C;
26.8 V for +30 °C;
26.7 V for +35 °C;
26.6 V for +40 °C
Recommended charging current Max. 1.75 A
Protection
Short-circuit protection Battery fuse 15 A/32 V
(FK2 flat fuse + holder)
Battery protection Valve control
Safety
Protective class Class III
UL/cUL (CSA) approval UL/cUL recognized (UL1778,
CSA 22.2 No. 107.1-95),
File E219627
Degree of protection (EN 60529) IP00
Operating specifications
Ambient temperature +5 to +40 °C
Transportation and storage temper-
ature range -20 to +50 °C
Self-discharge rate Approx. 3 % per month at
a battery temperature of 20 °C
Service life
The service life of the chemical lead-acid batteries (reduction to 50 % of
original capacity) depends on the battery temperature as follows:
At +20 °C Approx. 4 years
At +25 °C Approx. 3.5 years
At +30 °C Approx. 3 years
At +35 °C Approx. 2.5 years
At +40 °C Approx. 2 years
At +45 °C Approx. 1.5 years
At +50 °C Approx. 1 year
Mechanical specifications
Connection 1 terminal each for 0.08 to 4 mm2
for + BAT - BAT
Supplied accessories Accessory pack with FK2 spare
fuses 15 A and 20 A
Dimensions (W x H x D) in mm Approx. 186 x 168 x 121
Weight Approx. 6.0 kg
Mounting Can be screwed on level surface
(Keyhole mounting for hanging in
M4 screws)
Siemens KT10.1 · 2004
9/18
SITOP power · Standard 24 V
Battery module 12 Ah
Uninterruptible power supplies
9
■
Overview
• Battery for DC UPS module 6 A and 15 A and DC UPS module
40 A
• Contains two maintenance-free, sealed lead-acid batteries
from the same batch fitted in a holder and connected in series
• Completely prewired with battery fuse holder and terminals
• Accessory pack with FK2 spare fuses 15 A and 20 A
• Low self-discharge rate of approx. 3 % per month (at +20 °C)
1) For storage, installation and operation of the lead-acid batteries, the
appropriate DIN/VDE regulations or the country-specific directives (e.g.
VDE 0510 Part 2/EN 50272-2) must be observed. The battery location must
be sufficiently ventilated, potential ignition sources must be at least 50 cm
away.
■
Technical specifications
Battery module 12 Ah
Order No. 6EP1 935-6MF01
Battery type, charging current/
charging voltage
Maintenance-free, sealed lead-
acid batteries 1)
Recommended end-of-charge voltage (standby use)
• For +25 °C battery temperature 27.0 V DC
• For other battery temperatures 27.8 V for +10 °C;
27.3 V for +20 °C;
26.8 V for +30 °C;
26.7 V for +35 °C;
26.6 V for +40 °C
Recommended charging current Max. 3 A
Protection
Short-circuit protection Battery fuse 15 A/32 V
(FK2 flat fuse + holder)
Battery protection Valve control
Safety
Protective class Class III
UL/cUL (CSA) approval UL/cUL recognized (UL1778,
CSA 22.2 No. 107.1-95),
File E219627
Degree of protection (EN 60529) IP00
Operating specifications
Ambient temperature +5 to +40 °C
Transportation and storage temper-
ature range -20 to +50 °C
Self-discharge rate Approx. 3 % per month at
a battery temperature of 20 °C
Service life
The service life of the chemical lead-acid batteries (reduction to 50 % of
original capacity) depends on the battery temperature as follows:
At +20 °C Approx. 4 years
At +25 °C Approx. 3.5 years
At +30 °C Approx. 3 years
At +35 °C Approx. 2.5 years
At +40 °C Approx. 2 years
At +45 °C Approx. 1.5 years
At +50 °C Approx. 1 year
Mechanical specifications
Connection 1 terminal each for 0.08 to 4 mm2
for + BAT - BAT
Supplied accessories Accessory pack with FK2 spare
fuses 15 A and 20 A
Dimensions (W x H x D) in mm Approx. 253 x 118 x 121
Weight Approx. 9.0 kg
Mounting Can be screwed on level surface
(Keyhole mounting for hanging in
M4 screws)
Siemens KT10.1 · 2004
10
10/2 SITOP power flexi 120 W
10/2 SITOP power dual 15 V
10/2 SITOP modular 48 V/20 A
SITOP power
Alternative voltages
Siemens KT10.1 · 2004
10/2
SITOP power
Alternative voltages
10
■
Overview SITOP power flexi 120 W SITOP power dual 15 V SITOP modular 48 V/20 A
■
Application
■
Technical specifications
Continued on page 10/3.
The power supply unit with
adjustable output voltage
from 3 V to 52 V; suitable for all
applications where a special
voltage deviating from 24 V is
required.
The industry-standard power
supply unit with two 15 V out-
puts which can be connected
in parallel or in series; can be
used, for example, for supply-
ing electronic loads with
±15 V.
The modular 48 V power supply
unit with three-phase wide-
range input for powerful loads
which are powered by twice the
voltage instead of the usual
24 V.
Power supply, type 3 to 52 V/2 to 10 A 2 x 15 V/3.5 A 48 V/20 A
Order No. 6EP1 353-2BA00 6EP1 353-0AA00 6EP1 457-3BA00
Input Single-phase AC Single-phase AC Three-phase AC
Rated voltage Vin rated 120/230 V AC
Settable using wire jumper 120 to 230 V AC
wide-range input 400 to 500 V 3 AC
wide-range input
Voltage range 85 to 132 V/170 to 264 V AC 93 to 264 V AC 320 to 550 V
(startup from Vin > 340 V)
Overvoltage strength 2.3 x Vin rated, 1.3 ms Surge voltage acc. to
EN 61000-6-2 Table 4 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 10 ms at Vin = 93/187 V
(Pout = 120 W) > 10/40 ms at Vin = 120/187 V > 6 ms at Vin = 400 V
Rated line frequency; range 50/60 Hz, 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 2.2/0.9 A 1.9 to 1.15 A 2.2 A (Vin = 400 V)
Inrush current limitation (+ 25 °C) < 32 A < 30 A, typ. 3 ms < 70 A
I2t < 0.8 A2s< 3 A
2 s< 2.8 A
2s
Integrated line-side fuse T3.15 A/250 V (not accessible) T4 A/250 V (not accessible) none
Recommended circuit-breaker
(IEC 898) in mains supply line From 6 A Characteristic C From 10 A Characteristic C or
from 16 A Characteristic B Required: 3-pole coupled cir-
cuit-breaker 10 to 16 A Char. C
or motor circuit-breaker
3RV1021-1DA10, setting 3 A
Output Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 3 to 52 V DC 2 x 15 V DC 48 V DC
Total tolerance ± 1 % ± 2 % ± 3 %
• Stat. mains compensation Approx. 0.1 % Approx. 0.2 % Approx. ± 0.1 %
• Stat. load compensation Approx. 0.2 % Approx. 0.2 % Approx. ± 0.2 %
Sense line connection Yes, maximum voltage control
0.5 V per line --
Residual ripple (clock frequency:
approx. 50 kHz) < 50 mVpp < 50 mVpp (typ. 20 mVpp)< 100 mVpp
Spikes (bandwidth: 20 MHz) < 100 mVpp < 150 mVpp (typ. 150 mVpp)< 200 mVpp
Setting range 3 to 52 V, via potentiometer or
analog control voltage signal
0 to 2.5 V
14.5 to 17 V 42 to 56 V (max. 960 W)
Status display Green LED for 24 V O.K. Green LED for Vout >10 V
(summation display) Green LED for 48 V O.K.
Signalling Power Good via relay contact,
current monitor signal
0 to 2.5 V
-possible using signalling module
(6EP1 961-3BA10)
Power ON/OFF behavior No overshoot of Vout (soft start) Overshoot of Vout < 3% No overshoot of Vout (soft start)
Starting delay/voltage rise < 3 s/typ. 80 ms < 1 s < 2.5 s/< 500 ms
Rated current Iout rated 2 to 10 A (max. 120 W) 2 x 3.5 A 20 A
Current range
• up to + 45 °C 0 to 10 A (max. 120 W) 2 x 0 to 3.5 A 0 to 20 A
• up to + 60 °C 0 to 10 A (max. 120 W) 2 x 0 to 2.5 A 0 to 20 A
Siemens KT10.1 · 2004 10/3
SITOP power
Alternative voltages
10
■
Technical specifications (continued)
Power supply, type 3 to 52 V/2 to 10 A 2 x 15 V/3.5 A 48 V/20 A
Order No. 6EP1 353-2BA00 6EP1 353-0AA00 6EP1 457-3BA00
Dyn. V/I with
• Starting on short circuit Constant current 2 to 10 A Constant current approx. 23 A
• Short-circuit in operation Constant current 2 to 10 A typ. 60 A for 25 ms
Parallel connection for increased
output Yes, 2 Yes, 2 Yes, 2
Efficiency
Efficiency at Vout rated, Iout rated Approx. 84 % (at 24 V/5 A) Approx. 80 % Approx. 90 %
Power loss at Vout rated, Iout rated Approx. 23 W (at 24 V/5 A) Approx. 27 W Approx. 106 W
Protection and monitoring
Output overvoltage protection Yes, acc. to EN 60950 Yes, acc. to EN 60950 Yes, acc. to EN 60950
Current limitation 2 to 10 A, adjustable via potenti-
ometer or analog control volt-
age signal 0 to 2.5 V
Limit point < 4.9 A;
switch-off point < 6 A typ. 23 A
Short-circuit protection Electronic current limiting
(2 to 10 A) in the range 3 to12 V
or power limiting (120 W) in the
range 12 to 52 V
Electronic shutdown, automatic
restart Choice of stabilized current
characteristic approx. 23 A
or latching shutdown
Overload/short-circuit indicator Red LED for current or power
limiting -Yellow LED for "overload",
red LED for "latching shutdown"
Safety
Galvanic isolation primary/ second-
ary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I Class I
Discharge current < 3.5 mA < 3.5 mA < 3.5 mA
TÜV test Yes -Yes
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E143289 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M91), File E179336 Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259
FM approval - - -
Appr. for use in marine vessels - - -
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55011 Class A EN 55022 Class B
Line harmonics limitation EN 61000-3-2 - EN 61000-3-2
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range 0 to +60 °C with natural
convection 0 to +60 °C with natural convec-
tion, derating above +45 °C 0 to +60 °C with natural
convection
Transportation and storage tempera-
ture range -25 to + 85 °C -40 to +70 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721 Climatic class 3K3 acc. to
EN 60721 Climatic class 3K3 acc. to
EN 60721
Mechanical specifications
Connections
• Mains input L1, N, PE One screw-type terminal each
for 0.5 to 2.5 mm2
single-core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2
single-core/finely stranded
One screw-type terminal each
for 0.2 to 4 mm2
single-core/finely stranded
(L1, L2, L3, PE)
• Output One screw-type terminal for
0.5 to 2.5 mm2 (L+) and
2 screw-type terminals for
0.5 to 2.5 mm2 (M)
One screw-type terminal for
0.5 to 2.5 mm2
(P15_1, GND1, GDN2) and
2 screw-type terminals for
0.5 to 2.5 mm2 (P15_2)
2 screw-type terminals each for
0.33 to 10 mm2 (+, -)
• Messages, control inputs One screw-type terminal each
for 0.14 to 1.5 mm2--
Dimensions (W x H x D) in mm 75 x 125 x 125 75 x 125 x 125 240 x 125 x 125
Weight approx. Approx. 0.9 kg Approx. 0.75 kg 3.2 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Accessories - - Signalling module
(6EP1961-3BA10)
Siemens KT10.1 · 2004
10/4
SITOP power
Notes
Alternative voltages
10
Siemens KT10.1 · 2004
11
11/2 The IP65 version
11/2 The IP20 version
SITOP power
AS interface
power supplies
Siemens KT10.1 · 2004
11/2
SITOP power
Single-phase AS interface power supplies,
stabilized
AS interface power supplies
11
■
Overview The IP65 version The IP20 version
■
Application
■
Technical specifications
Continued on page 11/3.
The AS interface power sup-
ply unit with IP65 degree of
protection for any mounting
position is particularly suitable
for use in extremely harsh
environments. Thanks to the
24 V DC input voltage it is
ideally suitable for use to-
gether with a proven SITOP
power 24 V standard power
supply unit.
This AS interface power sup-
ply unit with its wide-range
input of 93 to 264 V AC and
110 to 350 V DC can be
universally used in all typical
power supply networks.
With limitation of the input
current harmonics acc. to
EN 61000-3-2; with SIMATIC
S7-300 design.
Power supply, type 2.4 A 7 A
Order No. 6EP1 632-1AL01 6EP1 354-1AL01
Input DC voltage Single-phase AC
Rated voltage Vin rated 24 V DC 120 to 230 V AC
wide-range input
Voltage range 20.4 to 28.8 V DC 93 to 264 V AC/110 to 350 V DC
Overvoltage strength 35 V DC for max. 500 ms 2.3 x Vin rated, 1.3 ms
Mains buffering at Iout rated > 10 ms > 20 ms at Vin = 93/187 V
Rated line frequency; range -0/50/60 Hz; 47 to 63 Hz
Rated input current Iin rated 3.6 A 2.2 to 1.2 A
Inrush current limitation (+25 °C) -< 20 A, < 3 ms
I2t- < 1.5 A
2s
Integrated line-side fuse T 6.3 A (not accessible) T 6.3 A (not accessible)
Recommended circuit-breaker
(IEC 898) in mains supply line From 10 A, Characteristic C or
from 6 A, Characteristic D From 16 A, Characteristic C
Output Stabilized, floating direct
voltage acc. to AS interface
specifications
Stabilized, floating direct
voltage acc. to AS interface
specification
Rated voltage Vout rated 30 V DC 30 V DC
Total tolerance 29.5 V to 31.6 V DC 29.5 to 31.6 V DC
Residual ripple < 300 mVpp < 300 mVpp
Spikes < 50 mVpp < 50 mVpp
Status display Green LED Green LED
Rated current Iout rated 2.4 A 7 A
Efficiency / power loss
Efficiency at Vout rated, Iout rated > 81% > 85%
Power loss at Vout rated, Iout rated < 17 W < 37 W
Protection and monitoring
functions
Output overvoltage protection -Yes
Current limiting From approx. 2.9 A From approx. 7.4 A
Short-circuit protection Constant current characteristic
approx. 2.9 A Constant current characteristic
approx. 7.4 A
Siemens KT10.1 · 2004 11/3
SITOP power
AS interface power supplies
Single-phase AS interface power supplies,
stabilized
11
1) In IP20 degree of protection with screw-type terminals on request.
2) The counterpart must be ordered separately (not included in the scope of
delivery); see Accessories.
Power supply, type 2.4 A 7 A
Order No. 6EP1 632-1AL01 6EP1 354-1AL01
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 Yes, SELV output voltage Vout
acc. to EN 60950
Protective class Class I Class I
Degree of protection (EN 60529) IP65 1) IP20
CE marking Yes Yes
UL/cUL (CSA) approval UL (UL 508), File 179336, CSA
(CSA 22.2 No. 14-95) cULus (UL 508, CSA 22.2
No.14-M91), File E143289
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable EN 61000-3-2
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range -25 to +55 °C 0 to +55 °C
Transportation and storage
temperature range -25 to +85 °C -25 to +85 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Input connections Circular connector 0.5 to
2.5 mm21)2) One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
Output connections AS i +
Output connections AS i -
Output connections Ground
500 mm three-core cable
AWG 14 1)
500 mm three-core cable
AWG 14 1)
500 mm three-core cable
AWG 14 1)
3 screw-type terminals for
0.5 to 2.5 mm2
3 screw-type terminals for
0.5 to 2.5 mm2
2 screw-type terminals for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 224 x 80 x 57 200 x 125 x 135
Weight approx. 1.0 kg 1.8 kg
Mounting Wall mounting, any mounting
position Snap-mounting on DIN rail
EN 50022-35x15 mm and S7 rail
Accessories 6-pin circular input connector
(6ES5 760-2CA11) and AS
interface coupling module PG
(3RG9 220-0AA00)
-
Siemens KT10.1 · 2004
11/4
SITOP power
Notes
AS interface power supplies
11
Siemens KT10.1 · 2004
12
12/2 Description
12/3 Specification sheet
SITOP power
Customized
Siemens KT10.1 · 2004
12/2
SITOP power
Customized
12
■
Overview
Our tried and tested standard power supplies cannot, of course,
be suitable for absolutely every application. Does your applica-
tion require a voltage level other than 24 V, or is a 19" or open-
frame version necessary, or are the environmental conditions of
your system sometimes outside the normal ranges? We offer the
possibility for optimum adaptation to your application-specific
requirements.
Thanks to the experience and know-how of our development
team, we are able to offer you a tailored solution by applying a
modular power supply concept. Your specific requirements can
be fulfilled by modifying existing equipment or by complete new
developments on the basis of pre-developed standard compo-
nents. Your advantages are evident:
• Adaptation of the power supply to your application, and not
vice versa as in the past
• Highly flexible electrical parameters
• AC or DC input
• Several output voltages possible
• High reliability through use of standard components
• Variability with respect to design requirements
• Adaptable mechanical system.
You therefore benefit from the competence of mass production
together with a maximum of development reliability and quality.
Further decisive criteria for the success of your application are:
• High availability thanks to fast development cycles
• Short time span between development and start of series pro-
duction thanks to tried and tested launch procedures
• Prices in line with the market.
Our customized solutions are currently in use in many sectors of
mechanical engineering, automation engineering, vehicle elec-
tronics, equipment design and industrial measurement engi-
neering, among others.
Our product range is open to any application. If you are inter-
ested and require further information, please copy the following
page, fill in the parameters of your specific requirement and fax
it to the stated number.
Form for inquiry is also available at:
http://intra1.nbgm.siemens.de/extern/spiegeln/
sitop/html_76/formular.htm
You can fill it out right on the screen and send it to us immedi-
ately. We will contact you without delay.
Siemens KT10.1 · 2004 12/3
SITOP power
Customized
12
■
FAX reply
Specification sheet for customized power supplies
Recipient: Sender:
SIEMENS AG
A&D SE PS 1
Würzburger Straße 121
90766 Fürth
FAX: 0911 750-9991
Company:
Department:
Name:
City:
FAX:
Phone:
Application:
Electrical requirements:
Input voltage: Vin: Tolerance D Vin :
Frequency: fin: Tolerance D fin :
Mains buffering time: Tin:
Output voltage: Vout1:Vout2:Vout3:Vout4:
Output current: Iout1:Iout2:Iout3:Iout4:
Other:
Mechanical requirements:
Design/dimensions:
(attach drawing if necessary)
Enclosure:
Connections: Other:
General requirements:
Efficiency:
Ambient temperature: Signalling:
Standards: EN 60950 UL cUL (CSA)
EN 61000-6-1/2 EN 61000-6-3/4
Quantity/year: Delivery:
Price expectations:
Remarks:
Siemens KT10.1 · 2004
12/4
SITOP power
Notes
Customized
12
Siemens KT10.1 · 2004
13
13/2 LOGO!Power 5 V
13/4 LOGO!Power 12 V
13/6 LOGO!Power 15 V
13/8 LOGO!Power 24 V
LOGO!Power
Siemens KT10.1 · 2004
13/2
LOGO!Power
LOGO!Power 5 V
13
■
Overview LOGO!Power 5 V
■
Application
■
Technical specifications
Continued on page 13/3.
LOGO!Power supplies are primary switched-mode power sup-
plies that are optimized to the LOGO! logic modules in terms of
functionality and design. With the wide input range of 85 V to
264 V AC, radio interference level B and assembly option in
built-in miniature distribution boards, they can be used univer-
sally in a diverse range of applications in the low-end perfor-
mance range.
Power supply, type 5V/3A 5 V/6.3 A
Order No. 6EP1 311-1SH02 6EP1 311-1SH12
Input Single-phase AC Single-phase AC
Rated voltage Vin rated 100 to 240 V AC
wide-range input 100 to 240 V AC
wide-range input
Voltage range 85 to 264 V AC 85 to 264 V AC
Overvoltage strength 2.3 x Vin rated/1.3 ms 2.3 x Vin rated/1.3 ms
Mains buffering at Iout rated > 40 ms at Vin = 187 V > 40 ms at Vin = 187 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 0.36 to 0.22 A 0.71 to 0.37 A
Inrush current limitation (+25 °C) < 15 A < 30 A
I2t < 0.8 A2s< 3 A
2s
Integrated line-side fuse Internal Internal
Recommended circuit-breaker
(IEC 898) in mains supply line From 16 A Characteristic B or
from 10 A Characteristic C From 16 A Characteristic B or
from 10 A Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 5 V DC 5 V DC
Total tolerance, static ± 3 % ± 3 %
• Static mains compensation Approx. 0.2 % Approx. 0.1 %
• Static load compensation Approx. 1.5 % Approx. 2 %
Residual ripple
(clock frequency approx. 90 kHz) < 100 mVpp < 100 mVpp
Spikes (bandwidth approx. 20 MHz) < 100 mVpp < 100 mVpp
Setting range 4.6 to 5.4 V 4.6 to 5.4 V
Status display Green LED for output voltage
OK Green LED for output voltage
OK
Power ON/OFF behavior No overshoot of Vout (soft start) No overshoot of Vout (soft start)
Starting delay/voltage rise < 0.5 s/typ. 15 ms < 0.5 s/typ. 10 ms
Rated current Iout rated 3 A 6.3 A
Current range up to +55 °C 0 to 3 A 0 to 6.3 A
Parallel connection for increased
output Yes Yes
Siemens KT10.1 · 2004 13/3
LOGO!Power
LOGO!Power 5 V
13
Power supply, type 5V/3A 5 V/6.3 A
Order No. 6EP1 311-1SH02 6EP1 311-1SH12
Efficiency
Efficiency at Vout rated, Iout rated typ. 76 % typ. 83 %
Power loss at Vout rated, Iout rated typ. 5 W typ. 6 W
Control
Dyn. mains compensation
(Vin rated ± 15 %) < 0.2 % Vout < 0.2 % Vout
Dyn. load compensation
(Iout: 10/90/10 %)
± 4 % Vout ± 6.5 % Vout
Settling time
• Load step from 10 to 90 % typ. 20 ms typ. 20 ms
• Load step from 90 to 10 % typ. 20 ms typ. 20 ms
Protection and monitoring
Current limitation typ. 3.8 A typ. 8.2 A
Short-circuit protection Stabilized current characteristic Stabilized current characteristic
RMS sustained short-circuit current < 5 A < 10 A
Overload/short-circuit indicator - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Protective class Class II (without PE conductor) Class II (without PE conductor)
CE marking Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
FM approval Yes, Class I Div. 2, Group A, B,
C, D T4 Yes, Class I Div. 2, Group A, B,
C, D T4
Appr. for use in marine vessels Yes, GL (Germanischer Lloyd) Yes, GL (Germanischer Lloyd)
Degree of protection (EN 60529) IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable Not applicable
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range -20 to +55 °C with natural
convection -20 to +55 °C with natural
convection
Transportation and storage
temperature range -40 to +70 °C -40 to +70 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Mains input connections L1, N One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
Connections
•Output +
•Output - 2 screw-type terminals each for
0.5 to 2.5 mm22 screw-type terminals each for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 54 x 90 x 55 72 x 90 x 55
Weight Approx. 0.17 kg Approx. 0.25 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x7.5/15 Snap-mounting on DIN rail
EN 50022-35x7.5/15
Siemens KT10.1 · 2004
13/4
LOGO!Power
LOGO!Power 12 V
13
■
Overview
■
Application
■
Technical specifications
Continued on page 13/5.
LOGO!Power supplies are primary switched-mode power sup-
plies that are optimized to the LOGO! logic modules in terms of
functionality and design. With the wide input range of 85 V to
264 V AC, radio interference level B and assembly option in
built-in miniature distribution boards, they can be used univer-
sally in a diverse range of applications in the low-end perfor-
mance range.
Power supply, type 12 V/1.9 A 12 V/4.5 A
Order No. 6EP1 321-1SH02 6EP1 322-1SH02
Input Single-phase AC Single-phase AC
Rated voltage Vin rated 100 to 240 V AC
wide-range input 100 to 240 V AC
wide-range input
Voltage range 85 to 264 V AC 85 to 264 V AC
Overvoltage strength 2.3 x Vin rated/1.3 ms 2.3 x Vin rated/1.3 ms
Mains buffering at Iout rated > 40 ms at Vin = 187 V > 40 ms at Vin = 187 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 0.53 to 0.3 A 1.13 to 0.61 A
Inrush current limitation (+25 °C) < 15 A < 30 A
I2t < 0.8 A2s< 3 A
2s
Integrated line-side fuse Internal Internal
Recommended circuit-breaker
(IEC 898) in mains supply line From 16 A Characteristic B or
from 10 A Characteristic C From 16 A Characteristic B or
from 10 A Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 12 V DC 12 V DC
Total tolerance, static ± 3 % ± 3 %
• Static mains compensation Approx. 0.2 % Approx. 0.1 %
• Static load compensation Approx. 1.5 % Approx. 1.5 %
Residual ripple
(clock frequency approx. 90 kHz) < 200 mVpp < 200 mVpp
Spikes (bandwidth approx. 20 MHz) < 300 mVpp < 300 mVpp
Setting range 10.5 to 16.1 V 10.5 to 16.1 V
Status display Green LED for output voltage
OK Green LED for output voltage
OK
Power ON/OFF behavior No overshoot of Vout (soft start) No overshoot of Vout (soft start)
Starting delay/voltage rise < 0.5 s/typ. 15 ms < 0.5 s/typ. 10 ms
Rated current Iout rated 1.9 A 4.5 A
Current range up to +55 °C 0 to 1.9 A 0 to 4.5 A
Parallel connection for increased
output Yes Yes
Siemens KT10.1 · 2004 13/5
LOGO!Power
LOGO!Power 12 V
13
Power supply, type 12 V/1.9 A 12 V/4.5 A
Order No. 6EP1 321-1SH02 6EP1 322-1SH02
Efficiency
Efficiency at Vout rated, Iout rated typ. 80 % typ. 85 %
Power loss at Vout rated, Iout rated typ. 5 W typ. 10 W
Control
Dyn. mains compensation
(Vin rated ± 15 %) < 0.2 % Vout < 0.2 % Vout
Dyn. load compensation
(Iout:10/90/10 %)
± 3 % Vout ± 4.2 % Vout
Settling time
• Load step from 10 to 90 % typ. 20 ms typ. 20 ms
• Load step from 90 to 10 % typ. 20 ms typ. 20 ms
Protection and monitoring
Current limitation typ. 2.5 A typ. 5.9 A
Short-circuit protection Stabilized current characteristic Stabilized current characteristic
RMS sustained short-circuit current < 4 A < 8 A
Overload/short-circuit indicator - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Protective class Class II (without PE conductor) Class II (without PE conductor)
CE marking Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
FM approval Yes, Class I Div. 2, Group A, B,
C, D T4 Yes, Class I Div. 2, Group A, B,
C, D T4
Appr. for use in marine vessels Yes, GL, ABS Yes, GL, ABS
Degree of protection (EN 60529) IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable Not applicable
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range -20 to +55 °C with natural
convection -20 to +55 °C with natural
convection
Transportation and storage
temperature range -40 to +70 °C -40 to +70 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Connections
• Mains input L1, N One screw-type terminal each
for 0.5 to 2.5 mm2 single-core/
finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-core/
finely stranded
•Output +
•Output - 2 screw-type terminals each for
0.5 to 2.5 mm22 screw-type terminals each for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 54 x 90 x 55 72 x 90 x 55
Weight Approx. 0.17 kg Approx. 0.25 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x7.5/15 Snap-mounting on DIN rail
EN 50022-35x7.5/15
Siemens KT10.1 · 2004
13/6
LOGO!Power
LOGO!Power 15 V
13
■
Overview
■
Application
■
Technical specifications
Continued on page 13/7.
LOGO!Power supplies are primary switched-mode power sup-
plies that are optimized to the LOGO! logic modules in terms of
functionality and design. With the wide input range of 85 V to
264 V AC, radio interference level B and assembly option in
built-in miniature distribution boards, they can be used univer-
sally in a diverse range of applications in the low-end perfor-
mance range.
Power supply, type 15 V/1.9 A 15 V/4 A
Order No. 6EP1 351-1SH02 6EP1 352-1SH02
Input Single-phase AC Single-phase AC
Rated voltage Vin rated 100 to 240 V AC
wide-range input 100 to 240 V AC
wide-range input
Voltage range 85 to 264 V AC 85 to 264 V AC
Overvoltage strength 2.3 x Vin rated/1.3 ms 2.3 x Vin rated/1.3 ms
Mains buffering at Iout rated > 40 ms at Vin = 187 V > 40 ms at Vin = 187 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 0.63 to 0.33 A 1.24 to 0.68 A
Inrush current limitation (+25 °C) < 15 A < 30 A
I2t < 0.8 A2s< 3 A
2s
Integrated line-side fuse Internal Internal
Recommended circuit-breaker
(IEC 898) in mains supply line From 16 A Characteristic B or
from 10 A Characteristic C From 16 A Characteristic B or
from 10 A Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 15 V DC 15 V DC
Total tolerance, static ± 3 % ± 3 %
• Static mains compensation Approx. 0.1 % Approx. 0.1 %
• Static load compensation Approx. 1.5 % Approx. 1.5 %
Residual ripple
(clock frequency approx. 90 kHz) < 200 mVpp < 200 mVpp
Spikes (bandwidth approx. 20 MHz) < 300 mVpp < 300 mVpp
Setting range 10.5 to 16.1 V 10.5 to 16.1 V
Status display Green LED for output voltage
OK Green LED for output voltage
OK
Power ON/OFF behavior No overshoot of Vout (soft start) No overshoot of Vout (soft start)
Starting delay/voltage rise < 0.5 s/typ. 15 ms < 0.5 s/typ. 10 ms
Rated current Iout rated 1.9 A 4 A
Current range up to +55 °C 0 to 1.9 A 0 to 4 A
Parallel connection for increased
output Yes Yes
Siemens KT10.1 · 2004 13/7
LOGO!Power
LOGO!Power 15 V
13
Power supply, type 15 V/1.9 A 15 V/4 A
Order No. 6EP1 351-1SH02 6EP1 352-1SH02
Efficiency
Efficiency at Vout rated, Iout rated typ. 80 % typ. 85 %
Power loss at Vout rated, Iout rated typ. 7 W typ. 11 W
Control
Dyn. mains compensation
(Vin rated ± 15 %) < 0.2 % Vout < 0.2 % Vout
Dyn. load compensation
(Iout: 10/90/10 %)
± 2.8 % Vout ± 3.3 % Vout
Settling time
• Load step from 10 to 90 % typ. 20 ms typ. 20 ms
• Load step from 90 to 10 % typ. 20 ms typ. 20 ms
Protection and monitoring
Current limitation typ. 2.7 A typ. 5.0 A
Short-circuit protection Stabilized current characteristic Stabilized current characteristic
RMS sustained short-circuit current < 4 A < 8 A
Overload/short-circuit indicator - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Protective class Class II (without PE conductor) Class II (without PE conductor)
CE marking Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
Yes, cULus listed (UL 508, CSA
22.2 No. 14-M95), File E197259;
cURus recognized (UL 60950,
CSA 22.2 No. 60950),
File E151273
FM approval Yes, Class I Div. 2, Group A, B,
C, D T4 Yes, Class I Div. 2, Group A, B,
C, D T4
Appr. for use in marine vessels Yes, GL (Germanischer Lloyd) Yes, GL (Germanischer Lloyd)
Degree of protection (EN 60529) IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable Not applicable
Interference immunity EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range -20 to +55 °C with natural
convection -20 to +55 °C with natural
convection
Transportation and storage
temperature range -40 to +70 °C -40 to +70 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Mains input connections L1, N One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
Connections
•Output +
•Output - 2 screw-type terminals each for
0.5 to 2.5 mm22 screw-type terminals each for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 54 x 90 x 55 72 x 90 x 55
Weight Approx. 0.17 kg Approx. 0.25 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Siemens KT10.1 · 2004
13/8
LOGO!Power
LOGO!Power 24 V
13
■
Overview
■
Application
■
Technical specifications
Continued on page 13/9.
LOGO!Power supplies are primary switched-mode power supplies that are optimized to the
LOGO! logic modules in terms of functionality and design. With the wide input range of 85 V to
264 V AC, radio interference level B and assembly option in built-in miniature distribution boards,
they can be used universally in a diverse range of applications in the low-end performance range.
Power supply, type 24 V/1.3 A 24 V/2.5 A 24 V/4 A
Order No. 6EP1 331-1SH02 6EP1 332-1SH42 6EP1 332-1SH51
Input Single-phase AC Single-phase AC Single-phase AC
Rated voltage Vin rated 100 to 240 V AC
wide-range input 100 to 240 V AC
wide-range input 100 to 240 V AC
wide-range input
Voltage range 85 to 264 V AC 85 to 264 V AC 85 to 264 V AC
Overvoltage strength 2.3 x Vin rated/1.3 ms 2.3 x Vin rated/1.3 ms 2.3 x Vin rated/1.3 ms
Mains buffering at Iout rated > 40 ms at Vin = 187 V > 40 ms at Vin = 187 V > 40 ms at Vin = 187 V
Rated line frequency; range 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz 50/60 Hz; 47 to 63 Hz
Rated current Iin rated 0.7 to 0.35 A 1.22 to 0.66 A 1.95 to 0.97 A
Inrush current limitation (+25 °C) < 15 A < 30 A < 30 A
I2t < 0.8 A2s< 3 A
2s< 2.5 A
2s
Integrated line-side fuse Internal Internal Internal
Recommended circuit-breaker
(IEC 898) in mains supply line From 16 A Characteristic B or
from 10 A Characteristic C From 16 A Characteristic B or
from 10 A Characteristic C From 16 A Characteristic B or
from 10 A Characteristic C
Output Stabilized, floating direct voltage Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC 24 V DC
Total tolerance, static ± 3 % ± 3 % ± 3 %
• Static mains compensation Approx. 0.1 % Approx. 0.1 % Approx. 0.1 %
• Static load compensation Approx. 1.5 % Approx. 1.5 % Approx. 1.5 %
Residual ripple
(clock frequency approx. 90 kHz) < 200 mVpp < 200 mVpp < 200 mVpp
Spikes (bandwidth approx. 20 MHz) < 300 mVpp < 300 mVpp < 300 mVpp
Setting range 22.2 to 26.4 V 22.2 to 26.4 V 22.2 to 26.4 V
Status display Green LED for output voltage
OK Green LED for output voltage
OK Green LED for output voltage
OK
Power ON/OFF behavior No overshoot of Vout (soft start) No overshoot of Vout (soft start) No overshoot of Vout (soft start)
Starting delay/voltage rise < 0.5 s/typ. 15 ms < 0.5 s/typ. 10 ms < 0.5 s/typ. 35 ms
Rated current Iout rated 1.3 A 2.5 A 4 A
Current range up to +55 °C 0 to 1.3 A 0 to 2.5 A 0 to 4 A
Parallel connection for increased
output Yes Yes Yes
Siemens KT10.1 · 2004 13/9
LOGO!Power
LOGO!Power 24 V
13
Power supply, type 24 V/1.3 A 24 V/2.5 A 24 V/4 A
Order No. 6EP1 331-1SH02 6EP1 332-1SH42 6EP1 332-1SH51
Efficiency
Efficiency at Vout rated, Iout rated typ. 82 % typ. 87 % typ. 89 %
Power loss at Vout rated, Iout rated typ. 7 W typ. 9 W typ. 12 W
Control
Dyn. mains compensation
(Vin rated ± 15 %) < 0.2 % Vout < 0.2 % Vout < 0.2 % Vout
Dyn. load compensation
(Iout: 10/90/10 %)
± 1.5 % Vout ± 1.5 % Vout ± 1.5 % Vout
Settling time
• Load step from 10 to 90 % typ. 20 ms typ. 20 ms typ. 20 ms
• Load step from 90 to 10 % typ. 20 ms typ. 20 ms typ. 20 ms
Protection and monitoring
Current limitation typ. 2 A typ. 3.4 A typ. 4.7 A
Short-circuit protection Stabilized current characteristic Stabilized current characteristic Stabilized current characteristic
RMS sustained short-circuit current < 4 A < 8 A < 10 A
Overload/short-circuit indicator - - -
Safety
Galvanic isolation
primary/secondary Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178 Yes, SELV output voltage Vout
acc. to EN 60950 and EN 50178
Protective class Class II (without PE conductor) Class II (without PE conductor) Class II (without PE conductor)
CE marking Yes Yes Yes
UL/cUL (CSA) approval Yes, cULus listed (UL 508, CSA
22.2), File E197259; cURus rec-
ognized (UL 60950, CSA 22.2),
File E151273
Yes, cULus listed (UL 508, CSA
22.2), File E197259; cURus rec-
ognized (UL 60950, CSA 22.2),
File E151273
Yes, cULus listed (UL 508, CSA
22.2), File E197259; cURus rec-
ognized (UL 60950, CSA 22.2),
File E151273
FM approval Yes, Class I Div. 2, Group A, B,
C, D T4 Yes, Class I Div. 2, Group A, B,
C, D T4 Available soon
Appr. for use in marine vessels Yes, GL, ABS Yes, GL, ABS Yes, ABS
Degree of protection (EN 60529) IP20 IP20 IP20
EMC
Interference emission EN 55022 Class B EN 55022 Class B EN 55022 Class B
Line harmonics limitation Not applicable Not applicable EN 61000-3-2
Interference immunity EN 61000-6-2 EN 61000-6-2 EN 61000-6-2
Operating specifications
Ambient temperature range -20 to +55 °C with natural
convection -20 to +55 °C with natural
convection -20 to +55 °C with natural
convection
Transportation and storage
temperature range -40 to +70 °C -40 to +70 °C -40 to +70 °C
Humidity rating Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation Climatic class 3K3 acc. to
EN 60721, no condensation
Mechanical specifications
Mains input connections L1, N One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
One screw-type terminal each
for 0.5 to 2.5 mm2 single-
core/finely stranded
Connections
•Output +
•Output - 2 screw-type terminals each for
0.5 to 2.5 mm22 screw-type terminals each for
0.5 to 2.5 mm22 screw-type terminals each for
0.5 to 2.5 mm2
Dimensions (W x H x D) in mm 54 x 90 x 55 72 x 90 x 55 90 x 90 x 55
Weight Approx. 0.17 kg Approx. 0.25 kg Approx. 0.34 kg
Mounting Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5 Snap-mounting on DIN rail
EN 50022-35x15/7.5
Siemens KT10.1 · 2004
13/10
LOGO!Power
Notes
13
Siemens KT10.1 · 2004
SITOP
L+
M
SITOP
L+
M
Load
G_KT01_EN_00017
14
14/2 Power supplies general
14/2 Stabilized DC power supplies
14/5 Mains specifications, line-side
connection
14/9 Possible system disturbances and
causes
14/10 Mounting, mounting areas and fixing
options
14/11 Planning aids
14/12 Parallel connection for redundant ope-
ration and performance enhancement
14/14 Series connection to increase the
voltage
14/15 Battery charging
14/15 Fusing of the output circuit, selectivity
Technical information
a
nd configuration
Siemens KT10.1 · 2004
14/2
Technical information and configuration
Power supplies general
14
■
Power supplies
In plant construction or mechanical engineering, or in any other
situations in which electrical controls are used, a safe and reli-
able power supply is needed to supply the process with power.
The functional reliability of electronic controls and therefore the
reliable operation of automated installations is extremely closely
linked to the resistance of the load power supply to failure. Final
control elements as well as input and output modules will only
respond to command signals if the power supply is operating
reliably.
In addition to general requirements such as reliability, particular
demands are placed on the electromagnetic compatibility
(EMC) of the power supply with reference to the tolerance range
of the output voltage as well as its ripple.
Important factors that determine problem-free implementation
are, in particular:
• An input current with a low harmonic content
• Low emitted interference and
• Adequate immunity (noise immunity) to interference
Certain disturbing phenomena
■
General notes on DC power supplies
The DC power supply is a static device with one or more inputs
and one or more outputs that converts a system of AC voltage
and AC current and/or DC voltage and DC current to a system
with different values of DC voltage and DC current by means of
electromagnetic induction for the purpose of transmitting electri-
cal energy.
The type of construction of a DC power supply is usually de-
cided by its intended use.
■
Unstabilized DC power supplies
The AC mains voltage is transformed using 50 Hz/60 Hz safety
transformers to a protective extra-low voltage and smoothed
with down-circuit rectification and capacitor filtering.
In the case of unstabilized DC power supplies, the DC output
voltage is not stabilized at a specific value, but the value is
varied in accordance with the variation in (mains) input voltage
and the loading.
The ripple is in the Volt range and is dependent on the loading.
The value for the ripple is usually specified as a percentage of
the DC output voltage level. Unstabilized DC power supplies
are characterized by their rugged, uncomplicated design that is
limited to the important factors and focussed on a long service
life.
Block diagram of an unstabilized power supply
■
Stabilized DC power supplies
Stabilized DC power supplies have electronic regulation circuits
that maintain the DC voltage at the output at a specific value with
as little variation as possible. Effects such as variation in input
voltage or changes in load at the output are electrically compen-
sated in the specified function area.
The ripple in the output voltage for stabilized DC power supplies
lies in the millivolt range and is mainly dependent on the loading
at the outputs.
Stabilized DC power supplies can be implemented on different
functional principles. The most common types of circuit are:
• Linear stabilized power supplies
• Magnetic voltage stabilizer
• Secondary pulsed switched-mode power supplies
• Primary pulsed switched-mode power supplies
The most suitable principle for a particular application case will
depend mainly on the application. The objective is to generate a
DC voltage to supply the specific load as inexpensively and as
accurately as possible.
EMC Types of interference
Emission (emitted interference) Interference caused by tele-
vision and radio reception
Interference coupling with data
lines or power supply cables
Immunity (immunity to inter-
ference) Faults on the power cable due to
switching non-resistive loads
such as motors or contactors
Static discharge due to lightning
strikes
Electrostatic discharge through
the human body
Conducted noise induced by
radio frequencies
50 Hz
~
+
Line isolation Rectification Filtering
V
out
G_KT01_EN_00067
Siemens KT10.1 · 2004 14/3
Technical information and configuration
Stabilized DC power supplies
14
■
Stabilized DC power supplies (continued)
Linear stabilized power supplies
Block diagram: Linear regulator
The linear regulator operates according to a conventional princi-
ple. The supply is provided from an AC supply system (one, two
or three conductor supply).
A transformer is used to adapt it to form the required secondary
voltage.
The rectified and filtered secondary voltage is converted into a
stabilized voltage at the output by a regulation section. The reg-
ulation section comprises a final control element and a control
amplifier. The difference between the stabilized output voltage
and the unstabilized voltage at the filter capacitor is converted
into a thermal loss in the final control element. The final control
element functions in this case like a rapidly changeable ohmic
impedance. The thermal loss that arises in each case is the
product of output current and voltage drop over the final control
element.
This system is extremely adaptable. Even without any further
modifications, several output voltages are possible. In the case
of multiple outputs, the individual secondary circuits are gener-
ated from separate secondary windings of the input transformer.
Some applications can only be resolved in accordance with this
circuit principle. Especially when highly accurate regulation,
minimal residual ripple and fast compensation times are re-
quired.
The efficiency is, however, poor and the weight and volume are
considerable. The linear regulator is therefore only an economi-
cal alternative at low power ratings.
Advantages:
• Simple, well-proven circuit principle
• Good to excellent control characteristics
• Fast settling time
Disadvantages:
• Relatively high weight and large volume due to the
50 Hz transformer
• Poor efficiency, heat dissipation problems
• Low storage time
Magnetic stabilizer
Block diagram: Magnetic stabilizer
The complete transformer comprises two components. The so-
called "ferro resonator" and a series connected auxiliary regula-
tion section. The input winding and the resonance winding of the
magnetic stabilizer are decoupled to a large extent by means of
the air gap. The magnetic stabilizer supplies a well-stabilized AC
voltage. This is rectified and filtered. The transformer itself is op-
erated in the saturation range.
The ferro resonator frequently has a linear regulator connected
to the output to improve the control accuracy. Secondary pulsed
switched-mode regulators are frequently also connected to the
output.
The magnetic stabilizer technique is reliable and rugged but is
also large-volume, heavy and relatively expensive.
Advantages:
• Good to excellent control characteristics in combination with
series connected linear regulators
• Significantly better efficiency than a linear regulator alone
Disadvantages:
• The ferro resonator is frequency dependent
• The power supplies are large and heavy due to the magnetic
components
Secondary pulsed switched-mode power supplies:
Block diagram: Secondary pulsed switched-mode power supply
Isolation from the supply system is implemented in this case with
a 50 Hz transformer. Following rectification and filtering, the en-
ergy is switched at the output by means of pulsing through a
switching transistor in the filtering and storage circuit. Thanks to
the transformer at the input, that acts as an excellent filter, the
mains pollution is low.
The efficiency of this circuit is extremely high.
This concept offers many advantages for power supplies with
numerous different output voltages.
To protect the connected loads, however, care must be taken; in
the event of the switching transistor breaking down, the full, un-
stabilized DC voltage of the filter capacitor will be applied to the
output. This danger, however, also exists in the case of linear
stabilized power supplies.
Advantages:
• Simple design and high efficiency
• Multiple outputs, also galvanically isolated from one another,
are easily implemented by means of several secondary wind-
ings
• Fewer problems with interference than with primary pulsed
switched-mode power supplies
Disadvantages:
• The 50 Hz transformer makes the power supplies relatively
large and heavy
• The output ripple (spikes) correspond to those of a primary
pulsed switched-mode power supply
Rectifier Filtering
electrolytic capacitor
Vout
Unstabilized
mains stabilized
Load
Transformer
G_KT01_EN_00177
Actuator
Ferro resonator in case of
readjustment
V
out stabilized
Stabilized output
voltage
Unstabilized
mains
G_KT01_EN_00178
Load
Secundary
switched-mode
regulator
Switching
transistor
Transformer
Filtering
Rectification
Unstabilized
mains V
out
Load
stabilized
G_KT01_EN_00179
Control
Siemens KT10.1 · 2004
14/4
Technical information and configuration
Stabilized DC power supplies
14
■
Stabilized DC power supplies (continued)
Primary pulsed switched-mode power supplies:
In other literature, the term SMPS (Switch Mode Power Supply)
or primary switched-mode regulator is often used.
Block diagram: Single-ended forward converter
The primary switched-mode regulators are available in many
different circuit variants. The most important basic circuits are
single-ended forward converters, flyback converters, half-
bridge converters, full-bridge converters, push-pull converters
and resonance converters.
The general principle of operation of the primary switched-mode
regulator is shown in the block diagram of the single-ended for-
ward converters.
The unstabilized supply voltage is first rectified and filtered. The
capacitance of the capacitor in the DC link determines the stor-
age time of the power supply on failure of the input voltage. The
voltage at the DC link is approximately 320 V DC for a 230 V
supply. A single-ended converter is then supplied with this DC
voltage and transfers the primary energy through a transformer
to the secondary side with the help of a pulse width regulator at
a high switching frequency. The switching transistor has low
power losses when functioning as a switch, so that the power
balance lies between > 70 % and 90 % depending on the output
voltage and current.
The volume of the transformer is small in comparison with a
50 Hz transformer due to the high switching frequency because
the transformer size taking into account the higher switching
frequency is smaller. Using modern semiconductors, switching
frequencies of 100 kHz and above can be achieved. At exces-
sively high switching frequencies, the switching losses increase,
so that in each case a compromise has to be made between a
high efficiency and the largest possible switching frequency. In
most applications, the switching frequencies lie between 20 kHz
and 250 kHz depending on the output power.
The voltage from the secondary winding is rectified and filtered.
The system deviation at the output is fed back to the primary cir-
cuit through an optocoupler. By controlling the pulse width (con-
ducting phase of the switching transistor in the primary circuit),
the necessary energy is transferred to the secondary circuit and
the output voltage is regulated. During the non-conducting
phase of the switching transistor, the transformer is demagne-
tized through an auxiliary winding. Just enough energy is trans-
ferred as is removed at the output.
The maximum pulse width for the pulse/pause ratio for these
circuits is < 50 %.
Advantages:
• Small magnetic components (transformer, storage reactor,
filter) thanks to the high operating frequency
• High efficiency thanks to pulse width regulation
• Compact equipment units
• Forced-air cooling is not necessary up to the kW range
• High storage times are possible on mains failure by increasing
the capacitance in the DC link
• Larger input voltage range is possible
Disadvantages:
• High cost circuit, many active components
• Higher costs for interference suppression
• The mechanical design must be in accordance with HF criteria
Primary switched-mode power supplies have become more and
more popular over the last few years. Especially due to the small
size, low weight, high efficiency and excellent price/perfor-
mance ratio.
Summary
The most important characteristics of the circuit types described
above are summarized in Table 2.
Comparison criteria for basic circuit variants
Single-ended forward converter
V
out stabilized
Load
Control
Unstabilized
mains
G_KT01_EN_00180
Circuit types
Comparison
criteria
Primary
switched-
mode
Secondary
switched-
mode
Linear
regulator
Magnetic
stabilizer
Input volt-
age range Very large Medium Very small Large
Regulation
speed Medium Medium Very fast Slow
Storage time
after power
failure
Very long Long Very short Long
Residual rip-
ple Medium Medium Very low Medium
Power loss Very small Small Large Very small
Frame size Very small Medium Very large Large
Weight Very light Medium Heavy Very heavy
Interference
suppression
costs
Very large Medium Low Medium
Siemens KT10.1 · 2004 14/5
Technical information and configuration
Mains specifications, line-side connection
14
■
Supply system data
When dimensioning and selecting plant components, the mains
data, mains conditions and the operating modes must be taken
into account for these components.
The most important data for a supply system is the rated voltage
and rated frequency. These data for the supply system are des-
ignated as rated values in accordance with international agree-
ments.
Rated voltage and rated frequency
Since May 1987, the standard DIN IEC 60038 "IEC rated volt-
ages" has been applicable in the Federal Republic of Germany.
The international standard IEC 60038, Edition 6, 1983, "IEC stan-
dard voltages” has been included in this standard unmodified.
The IEC 60038 standard is the result of an international agree-
ment to reduce the diverse rated voltage values that are in use
for electrical supply networks and traction power supplies, load
installations and equipment.
Conversion of low-voltage supply systems
In the low-voltage range, it is emphasized in IEC 60038 that
220/380 V and 240/415 V voltage values for three-phase elec-
tricity supplies have been replaced by a single internationally
standardized value of 230/400 V.
The tolerances for the rated voltages of the supply systems that
were specified for the transition period up to 2003 were intended
to ensure that equipment rated for the previous voltages could
be operated safely until the end of its service life.
Conversion of low-voltage supply systems
The IEC recommendations have been implemented as national
regulations in the most important countries, as far as the condi-
tions in the country allow.
■
International supply voltages and frequencies in low-voltage supply systems
1) Industry only.
2) No further expansion.
3) From 2003.
Year Rated voltage Tolerance range
Up to 1987 220 V/380 V -10 % to +10 %
From 1988 to 2003 230 V/400 V -10 % to + 6 %
From 2003 230 V/400 V -10 % to +10 %
Country Mains voltage
Western Europe:
Belgium 50 Hz 230/400 – 127-220 V
Denmark 50 Hz 230/400 V
Germany 50 Hz 230/400 V
Finland 50 Hz 230/400-5001) – 6601) V
France 50 Hz 127/220 – 230/400 – 5001) – 380/6601) – 525/9101) V
Greece 50 Hz 230/400 – 127/2202) V
Great Britain 50 Hz (230/400 V)3)
Ireland 50 Hz 230/400 V
Iceland 50 Hz 127/2202) – 230/400 V
Italy 50 Hz 127/220 – 230/400 V
Luxembourg 50 Hz 230/400 V
Netherlands 50 Hz 230/400 – 6601) V
Northern Ireland 50 Hz 230/400 – Belfast 220/380 V
Norway 50 Hz 230-230/400-5001) – 6901) V
Austria 50 Hz 230/400 – 5001) – 6901) V
Portugal 50 Hz 230/400 V
Sweden 50 Hz 230/400 V
Switzerland 50 Hz 230/400 – 5002) V
Spain 50 Hz 230/400 V
Eastern Europe
Albania 50 Hz 230/400 V
Bulgaria 50 Hz 230/400 V
Russian Federation 50 Hz 230/400 – 6901) V
Croatia 50 Hz 230/400 V
Poland 50 Hz 230/400 V
Rumania 50 Hz 230/400 V
Serbia 50 Hz 230/400 V
Slovakia 50 Hz 230/400 – 5001) – 6901) V
Slovenia 50 Hz 230/400 V
Chechnya 50 Hz 230/400 – 5001) – 6901) V
Hungary 50 Hz 230/400 V
Siemens KT10.1 · 2004
14/6
Technical information and configuration
Mains specifications, line-side connection
14
■
International supply voltages and frequencies in low-voltage supply systems (continued)
1) Industry only.
2) No further expansion.
Country Mains voltage
Middle-East:
Afghanistan 50 Hz 220/380 V
Bahrain 50 Hz 230/400 V
Cyprus 50 Hz 240/415 V
Iraq 50 Hz 220/380 V
Israel 50 Hz 230/400 V
Jordan 50 Hz 220/380 V
Kuwait 50 Hz 240/415 V
Lebanon 50 Hz 110/190 – 220/380 V
Oman 50 Hz 220/380 – 240/415 V
Qatar 50 Hz 240/415 V
Saudi Arabia 60 Hz 127/220 – 220/380 – 4801) V (220/380 – 240/415 V 50 Hz: remainder only)
Syria 50 Hz 115/200 – 220/380 – 4001) V
Turkey 50 Hz 220/380 V (parts of Istanbul: 110/190 V)
United Arab Emirates
(Abu Dhabi; Ajman; Dubai; Fujayrah;
Ras al Khaymah; Sharjah; Um al Qaywayn)
50 Hz 220/380 – 240/415 V
Yemen (North) 50 Hz 220/380 V
Yemen (South) 50 Hz 230/400 V
Far East:
Bangladesh 50 Hz 230/400 V
Burma 50 Hz 230/400 V
Peoples Republic of China 50 Hz 127/220 – 220/380 V (in mining: 1140 V)
Hong Kong 50 Hz 200/346 V
India 50 Hz 220/380 – 230/400 – 240/415 V
Indonesia 50 Hz 127/220 – 220/380 – 4001) V
Japan 50 Hz 100/200 – 4001) V
South Honshu, Shikoku, Kyushu, Hokkaido, North
Honshu 60 Hz 110/220 – 4401) V
Cambodia 50 Hz 120/208 V – Phnom Penh 220/238 V
Korea (North) 60 Hz 220/380 V
Korea (South) 60 Hz 100/2002) – 220/380 – 4401) V
Malaysia 50 Hz 240/415 V
Peoples Republic of Mongolia 50 Hz 220/380 V
Pakistan 50 Hz 230/400 V
Philippines 60 Hz 110/220 – 440 V
Singapore 50 Hz 240/415 V
Sri Lanka 50 Hz 230/400 V
Taiwan 60 Hz 110/220 – 220 – 440 V
Thailand 50 Hz 220/380 V
Vietnam 50 Hz 220/380 V
North America:
Canada 60 Hz 600 – 120/240 – 460 – 575 V
USA 60 Hz 120/208 – 120/240 – 277/480 – 6001) V
Central America:
Bahamas 60 Hz 115/200 – 120/208 V
Barbados 50 Hz 110/190 – 120/208 V
Belize 60 Hz 110/220 – 220/440 V
Costa Rica 60 Hz 120/2082) – 120/240 – 127/220 – 254/4402) – 227/4801) V
Dominican Republic 60 Hz 120/208 – 120/240 – 4801) V
Siemens KT10.1 · 2004 14/7
Technical information and configuration
Mains specifications, line-side connection
14
■
International supply voltages and frequencies in low-voltage supply systems (continued)
1) Industry only.
2) No further expansion.
Country Mains voltage
Central America (continued):
Guatemala 60 Hz 120/208 – 120/240 – 127/220 – 277/4801) – 4801) – 5501) V
Haiti 50 Hz 220/380 V (Jacmel), 60 Hz 110/220 V
Honduras 60 Hz 110/220 – 127/220 – 277/480 V
Jamaica 50 Hz 110/220 – 4401) V
Cuba 60 Hz 120/240 – 220/380 – 277/4801) – 4401) V
Mexico 60 Hz 127/220 – 4401) V
Nicaragua 60 Hz 110/220 – 120/240 – 127/220 – 220/440 – 254/401) V
Panama 60 Hz 120/2081) – 120/240 – 254/4401) – 277/4801) V
Puerto Rico 60 Hz 120/208 – 480 V
El Salvador 60 Hz 110/220 – 120/208 – 127/220 – 220/440 – 240/4801) – 254/4401) V
Trinidad 60 Hz 110/220 – 120/240 – 230/400 V
South America:
Argentina 50 Hz 220/380 V
Bolivia 60 Hz 220/380 – 480 V, 50 Hz 110/220 – 220/380 V (exception)
Brazil 60 Hz 110/220 – 220/440 – 127/220 – 220/380 V
Chile 50 Hz 220/380 V
Ecuador 60 Hz 120/208 – 127/220 V
Guyana 50 Hz 110/220 V (Georgetown), 60 Hz 110/220 – 240/480 V
Columbia 60 Hz 110/220 – 150/260 – 440 V
Paraguay 60 Hz 220/380 – 220/440 V
Peru 60 Hz 220 – 220/380/440 V
Surinam 60 Hz 115/230 – 127/220 V
Uruguay 50 Hz 220 V
Venezuela 60 Hz 120/208 – 120/240 – 208/416 – 240/480 V
Africa:
Egypt 50 Hz 110/220 – 220/380 V
Ethiopia 50 Hz 220/380 V
Algeria 50 Hz 127/220 – 220/380 V
Angola 50 Hz 220/380 V
Benin 50 Hz 220/380 V
Ivory Coast 50 Hz 220/380 V
Gabon 50 Hz 220/380 V
Ghana 50 Hz 127/220 – 220/380 V
Guinea 50 Hz 220/380 V
Kenya 50 Hz 220/380 V
Cameroon 50 Hz 127/220 – 220/380 V
Congo 50 Hz 220/380 V
Liberia 60 Hz 120/208 – 120/240 V
Libya 50 Hz 127/220 2) – 220/380 V
Madagascar 50 Hz 127/220 – 220/380 V
Malawi 50 Hz 220/380 V
Mali 50 Hz 220/380 V
Morocco 50 Hz 115/200 – 127/220 – 220/380 – 5001) V
Mauritius 50 Hz 240/415 V
Mozambique 50 Hz 220/380 V
Namibia 50 Hz 220/380 V
Niger 50 Hz 220/380 V
Siemens KT10.1 · 2004
14/8
Technical information and configuration
Mains specifications, line-side connection
14
■
International supply voltages and frequencies in low-voltage supply systems (continued)
■
Connection and fusing on the line side
All SITOP and LOGO!Power supplies are built-in devices. For
installation of the devices, the relevant DIN/VDE specifications
or country-specific regulations must be taken into account. The
supply voltage must be connected in accordance with VDE
0100 and VDE 0160. On installation, protective gear and isolat-
ing gear must be provided for disconnecting the power supply.
Power supply units cause a current inrush immediately after
application of the input voltage due to charging of the load ca-
pacitor; it soon falls back to the rated input current level after a
few milliseconds. Aside from the internal impedances of the
power supply, the current inrush is largely dependent on the size
of the input voltage applied as well as the source impedance of
the supply network and the line impedance of the supply line.
The maximum current inrush for SITOP power supplies is speci-
fied in the applicable technical data. It is important for dimen-
sioning up-circuit protective devices.
Single-phase SITOP and LOGO!Power supplies are equipped
with internal device protection (fuses). For connection to the
supply system, only one protective device (fuse or circuit-
breaker) must be provided for conductor protection in accor-
dance with the current rating of the installed cable. The circuit-
breakers recommended in the data sheets and operating in-
structions have been selected such that even during the maxi-
mum current inrush that can occur under worst case conditions
on switching on the supply voltage, the circuit-breaker will not
trip.
Three-phase SITOP power supplies do not have internal device
protection. The up-circuit protective device (three-phase cou-
pled miniature circuit-breaker or motor protection switch) pro-
tects the cables and devices. The protective devices specified
in the data sheets and operating instructions are optimized to
the characteristics of the relevant power supplies.
1) Industry only.
Country Mains voltage
Africa (continued):
Nigeria 50 Hz 220/415 V
Rwanda 50 Hz 220/380 V
Zambia 50 Hz 220/380 V – 415 – 5501) V
Senegal 50 Hz 127/220 – 220/380 V
Sierra Leone 50 Hz 220/380 V
Somalia 50 Hz 220-220/440 V
Sudan 50 Hz 240/415 V
South Africa 50 Hz 220/380 – 5001) – 550/9501) V
Swaziland 50 Hz 220/380 V
Tanzania 50 Hz 230/400 V
Togo 50 Hz 127/220 – 220/380 V
Tunisia 50 Hz 115/200 – 220/380 V
Uganda 50 Hz 240/415 V
Zaire 50 Hz 220/380 V
Zimbabwe 50 Hz 220/380 V
Siemens KT10.1 · 2004 14/9
Technical information and configuration
Possible system disturbances and causes
14
■
Overview
The quality of the mains voltage has become a decisive factor in
the functioning, reliability, maintenance costs and service life of
highly sensitive electronic installations and devices (computers,
industrial controls, instrumentation, etc.).
Mains disturbances cause system failures and affect the func-
tion of plants as well as electronic consumers. They can also
result in total failure of the installation or equipment.
The most frequent types of disturbance are:
• Long-term overvoltages
• Long-term undervoltages
• Burst interference and transients
• Voltage reduction and surges
• Electrical noise
• Momentary mains breaks
• Long-term mains breaks
Mains disturbances can be caused by a number of things, e.g.:
• Switching operations in the supply system
• Long cable paths in the supply system
• Environmental influences, such as storms
• Mains overloads
Typical causes of mains disturbances generated in-house are:
• Thyristor-controlled drives
• Lifts, air-conditioning, photocopiers
• Motors, power factor correction equipment
• Electrical welding, large machines
• Switching of lighting equipment
Disturbances in mains voltages can occur individually or in combination. Possible reasons for these disturbances and reactions
can be:
Mains disturbances and effects
The SITOP product family offers a range of possibilities for minimizing or preventing the risk of mains disturbances at the planning
stage.
Mains disturbances Percentage of total
disturbance
Effect
Overvoltage
Over a long period, the mains voltage is exceeded by
more than +6% (acc. to DIN IEC 60038)
approx. 15% - 20% Can result in overheating and even thermal destruction of
individual components. Causes total failure.
Undervoltage
Over a long period, the mains voltage is reduced by
more than 10% (acc. to DIN IEC 60038)
approx. 20% - 30% Can result in undefined operating states for loads. Causes
data errors.
Burst interference
Energy-rich impulses (e.g. 700 V/1 ms) and energy-
poor transients (e.g. 2500 V/20 µs) result from switch-
ing operations in the supply system
approx. 30% - 35% Can result in undefined operating states for the loads and
can lead to the destruction of components.
Voltage reduction and surges
The voltage level changes suddenly and in an uncon-
trolled manner, e.g. due to changes in loading and
long cable runs
approx. 15% - 30% Can result in undefined operating states and destruction of
components. Causes data errors.
Electrical noise
A mix of frequencies superimposed on the mains due
to bad grounding and/or strong HF emitters,
such as television transmitters or storms
approx. 20% - 35% Can result in undefined operating states for loads. Causes
data errors.
Voltage interruption
Short-term interruption of the mains voltage (up to
10 ms), due to short-circuiting in neighboring supply
systems or starting of large electrical machines
approx. 8% - 10% Can result in undefined operating states for loads especially
those with insufficient mains buffering. Causes data errors.
Voltage interruption
Long interruption of the mains voltage (longer than
10 ms)
approx. 2% - 5% Can result in undefined operating states for loads especially
those with insufficient mains buffering. Causes data errors.
Siemens KT10.1 · 2004
14/10
Technical information and configuration
Mounting, Mounting areas
and fixing options
14
■
Mounting
All SITOP and LOGO!Power supplies are built-in devices. With
the exception of the variants with IP65 degree of protection, the
power supplies must be mounted vertically so that the air can
enter the ventilation slots at the bottom of the devices and leave
through the upper part of the devices. If the units are not
mounted vertically (at your own risk), the ambient temperature
should not exceed +45 °C and the load current should not ex-
ceed approx. 50% of the rated current value. Variants with IP65
degree of protection can be mounted in any mounting position.
The minimum distances specified in the corresponding operat-
ing manual for the top, bottom, and side of the devices must be
observed to ensure free air convection.
■
Mounting areas and fixing options
Power supply Order No. Required mounting
area in mm (W x H)
Mounting on a standard rail
acc. to DIN EN 50022
Wall mounting
35 x 7.5 mm 35 x 15 mm
SITOP power 24 V, one-phase and two-phase power supplies
24 V/0.5 A 6EP1331-2BA10 22.5 x 180 X X
24 V/0.375 A 6EP1731-2BA00 22.5 x 180 X X
24 V/2 A 6EP1331-2BA00 50 x 225 X X
6ES7307-1BA00-0AA0 50 x 205 1)
6ES7305-1BA80-0AA0 80 x 225 1)
6EP1732-0AA00 80 x 235 X X
24 V/2.5 A 6EP1332-1SH12 80 x 335 X X
24 V/3.5 A 6EP1332-1SH31 160 x 280 X X X
24 V/4 A 6EP1332-1SH22 80 x 335 X X
24 V/5 A 6EP1333-3BA00 70 x 225 X X
6EP1333-2BA00 75 x 225 X X
6EP1333-2AA00 75 x 225 X X
6ES7307-1EA00-0AA0 80 x 205 1)
6ES7307-1EA80-0AA0 80 x 225 1)
6EP1333-1AL12 160 x 230 X X
24 V/10 A 6EP1334-3BA00 90 x 225 X X
6EP1334-2BA00 100 x 225 X X
6EP1334-2AA00 100 x 225 X X
6EP1334-2CA00 160 x 290 X
6ES7307-1KA01-0AA0 120 x 205 1)
6EP1334-1AL12 160 x 230 X X
6EP1334-1SH01 200 x 325 X
24 V/20 A 6EP1336-3BA00 160 x 225 X X
6EP1336-2BA00 320 x 225 X X
6EP1536-2AA00 320 x 280 X X
24 V/40 A 6EP1337-3BA00 240 x 225 X X
SITOP power 24 V, three-phase power supplies
24 V/10 A 6EP1434-2BA00 320 x 225 X X
24 V/20 A 6EP1436-3BA00 160 x 225 X X
6EP1436-2BA00 320 x 225 X X
24 V/30 A 6EP1437-2BA00 320 x 280 X X
24 V/40 A 6EP1437-3BA00 240 x 225 X X
6EP1437-2BA10 320 x 280 X X
SITOP power 24 V, uninterruptible power supplies
DC UPS 6 A
(with serial interface /
USB interface)
6EP1931-2DC21
(-2DC31/-2DC41) 50 x 225 X X
DC UPS 15 A
(with serial interface /
USB interface)
6EP1931-2EC21
(-2EC31/-2EC41) 50 x 225 X X
DC UPS 40 A 6EP1931-2FC01 280 x 290 X X
Siemens KT10.1 · 2004 14/11
Technical information and configuration
Planning aids
14
1) With an additional mounting adapter.
■
Planning aids
For planning and construction, operating manuals with mounting
options, dimension drawings, and principle circuits with pin
names in different file formats (suitable for CAD applications) are
available for download on the Internet.
Additional information is available in the Internet under:
http://www.siemens.com/automation/sitop
35 x 7.5 mm 35 x 15 mm
SITOP power 24 V, uninterruptible power supplies
Battery module 2.5 Ah 6EP1935-6MD31 285 x 171 X X X
Battery module 3.2 Ah 6EP1935-6MD11 210 x 171 X X X
Battery module 7 Ah 6EP1935-6ME21 206 x 188 X
Battery module 12 Ah 6EP1935-6MF01 273 x 138 X
SITOP power 24 V, additional components
Buffer module 6EP1961-3BA00 70 x 225 X X
Redundancy module 6EP1961-3BA20 70 x 225 X X
Diagnosis module 6EP1961-2BA00 72 x 190 X X
SITOP power alternative voltages
3-52 V/120 W 6EP1353-2BA00 75 x 225 X X
2 x 15 V/3.5 A 6EP1353-0AA00 75 x 325 X X
48 V/20 A 6EP1457-3BA00 240 x 255 X X
SITOP power AS interface
30 V/2.4 A 6EP1632-1AL01 260 x 80 X
30 V/7 A 6EP1354-1AL01 200 x 325 X
LOGO!Power supplies
5 V/3 A 6EP1311-1SH02 54 x 130 X X
12 V/1.9 A 6EP1321-1SH02 54 x 130 X X
15 V/1.9 A 6EP1351-1SH02 54 x 130 X X
24 V/1.3 A 6EP1331-1SH02 54 x 130 X X
5 V/6.3 A 6EP1311-1SH12 72 x 130 X X
12 V/4.5 A 6EP1322-1SH02 72 x 130 X X
15 V/4 A 6EP1352-1SH02 72 x 130 X X
24 V/2.5 A 6EP1332-1SH42 72 x 130 X X
24 V/4 A 6EP1332-1SH51 90 x 130 X X
Power supply Order No. Required mounting
area in mm (W x H)
Mounting on a standard rail
acc. to DIN EN 50022
Wall mounting
Siemens KT10.1 · 2004
14/12
Technical information and configuration
Parallel connection for redundant operation
and performance enhancement
14
■
Parallel connection for redundant operation
Two SITOP power supplies of the same type can be connected
in parallel through diodes for a redundant configuration. Hun-
dred percent redundancy only exists for two power supplies
when the total load current is no higher than that which one
power supply can supply alone and when the supply for the pri-
mary side is also implemented redundantly (i.e. a short-circuit on
the primary side will not trigger a shared fuse which would dis-
connect both power supplies from the mains).
Parallel connection with decoupling diodes for redundant oper-
ation is permitted for all SITOP power supplies. The diodes V1
and V2 are used for decoupling. They must have a blocking volt-
age of at least 40 V and it must be possible to load them with a
current equal to or greater than the maximum output current of
the respective SITOP power supply. For diode dimensioning,
see the following note "General information on selection of di-
odes".
As a simple alternative to diode dimensioning, the prepared
add-on module "SITOP modular redundancy module" (Order No.
6EP1961-3BA20, see Section 8) is available for redundant con-
nection of two power supplies.
General information on selection of diodes:
The diodes must be dimensioned for the maximum dynamic cur-
rent. This can be the dynamic current during power-up in the
short-circuit case or the dynamic current during a short-circuit in
operation (the largest of the two values should be taken from the
relevant technical specifications).
To dissipate the significant power losses of the decoupling di-
odes (current x diode conductive-state voltage), the diodes
must be mounted on suitably dimensioned heat sinks.
An additional safety margin is recommended, because the out-
put capacitor integral to the power supply generates an addi-
tional peak current in the short-circuit case. This additional cur-
rent flows only for a few milliseconds which is a period (< 8.3 ms,
so-called permissible surge current for diodes) in which diodes
are permitted to be loaded with a multiple of the rated current.
Parallel connection of two SITOP power supplies for redundant operation
Example 1
Two single-phase SITOP modular power supplies with 10 A
rated output current (Order No.: 6EP1334-3BA00) are con-
nected in parallel. The dynamic current in the event of a short-
circuit during operation is approx. 30 A for 25 ms.
The diodes should therefore have a loading capability of 40 A to
be safe, the common heat sink for both diodes must be dimen-
sioned for the maximum possible current of approx. 24 A (RMS
sustained short-circuit current) x diode conductive-state volt-
age.
Example 2
Two SITOP power supplies with 40 A rated output current (Order
No. 6EP1437-2BA10) are connected in parallel. The dynamic
current in the event of a short-circuit during operation is approx.
70 A for 600 ms, the RMS value is < 54 A.
The selected diodes should therefore have a loading capability
of 100 A to be safe, the heat sink per diode must be dimensioned
for the continuous possible current of 54 A x diode conductive-
state voltage.
SITOP
L+
M
SITOP
L+
M
Load
G_KT01_EN_00017
Siemens KT10.1 · 2004 14/13
Technical information and configuration
Parallel connection for redundant operation
and performance enhancement
14
■
Parallel connection for performance enhancement
To enhance performance, identical types of most SITOP power
supplies can be connected in parallel galvanically (the same
principle as parallel connection for redundant operation, but
without decoupling diodes):
Advantage
The costs for mounting the diodes onto heat sinks and the not
insignificant power losses of the decoupling diodes (current x
diode conducting-state voltage) are avoided.
The types permitted for direct galvanic parallel connection are
listed in the relevant technical specifications under "Output, par-
allel connection for performance enhancement“.
Precondition
• The output cables connected to terminals L+ and M of every
SITOP power supply should be installed with an identical
length and cross-section (or the same impedance) to the com-
mon external linking point.
• The SITOP power supplies connected in parallel must be
switched simultaneously using a common switch in the mains
supply line (e.g. using the main switch available in control cab-
inets).
• The output voltages of the power supplies must be measured
under no-load operation before they are connected in parallel
and are permitted to differ by up to 50 mV. This usually corre-
sponds to the factory default setting. If the output voltage is
changed in the case of variable power supplies, the M termi-
nals should first be connected and then the voltage difference
between the L+ output terminals measured under no-load con-
ditions before these are connected. This voltage difference
must not exceed 50 mV.
Note
With a direct galvanic connection in parallel of more than two
SITOP power supplies, further circuit measures may be neces-
sary for short-circuit and overload protection!
■
Parallel connection for redundant operation and for performance enhancement
Almost 100% redundancy
Using the types permitted for direct galvanic parallel connection
(see the relevant technical specifications under "Output, parallel
connection for performance enhancement"), the performance
can be increased without the need for decoupling diodes and
redundancy of almost 100% can be implemented by direct gal-
vanic parallel connection of an additional power supply of the
same type to the power supplies required to satisfy the perfor-
mance requirements. This means that at least one more power
supply is required than is necessary for the sum of all load cur-
rents.
A decoupling diode is normally required for redundancy to en-
sure that a power supply that has failed as a result of short-cir-
cuiting of the outputs (especially as a result of short-circuiting
the output electrolytic capacitor) does not also short-circuit the
power supply that remains intact. A redundancy of almost 100%
can be implemented with this type of circuit.
Example
A load current of up to 40 A is required, the power supply must
operate on both 400 V and 500 V three-phase supplies (without
switch-over).
The three-phase 20 A SITOP modular power supply (Order No.:
6EP1436-3BA00) is suitable for this purpose. For load currents
up to 40 A, direct galvanic parallel connection of two SITOP
modular power 20 supplies is necessary. By connecting another
SITOP modular 20 in parallel, performance enhancement and
redundancy are implemented simultaneously (if one of the three
power supplies fails to supply an output voltage, the remaining
two 20 A power supplies are capable of supplying a total load
current of 40 A).
Note
With a direct galvanic connection in parallel of more than two
SITOP power supplies, further circuit measures may be neces-
sary for short-circuit and overload protection!
Siemens KT10.1 · 2004
14/14
Technical information and configuration
Series connection to increase the voltage
14
■
Series connection to increase the voltage
To generate a load voltage of e.g. 48 V DC, two 24 V SITOP
power supplies of the same type can be connected in series.
The SITOP outputs L+ and M are isolated up to at least 60 V DC
against PE (air gaps and creepage distances as well as radio in-
terference suppression capacitors on L+ and M against PE), so
that with this type of series connection (see Figure), the following
points can be earthed:
• M of the lower power supply (results in +48 V DC against PE)
• Midway M/L+ between both power supplies (results in
± 24 V DC against PE)
• L+ of the upper power supply (results in – 48 V DC against PE)
Note:
If two devices are connected in parallel, it cannot be guaranteed
that the voltage will remain below maximum permissible SELV
voltage of 60 V DC in the event of a fault.
The purpose of diodes V1 and V2 is to protect the electrolytic
output capacitor integrated in the power supply against reverse
voltages > 1 V. As a result of the not absolutely simultaneous
power-up (even when a common mains switch is used for
switching on, differences of a few tens of milliseconds can occur
between the various start-up delays), the SITOP power which
starts up more quickly supplies current from output L+ to the M
output of the slower SITOP power whose output electrolytic ca-
pacitor is then theoretically impermissibly discharged.
The internal LC filter causes the internal rectifier diode on the
secondary side to accept this current a few milliseconds later;
this means that the external diode connected with its anode to M
and cathode to L+ is essential on each power supply. These di-
odes are, however, only loaded dynamically, so the 8.3 ms surge
current loading capability (specified in the data sheets for suit-
able diodes) can be used as a basis for dimensioning and it is
not usually necessary to cool the diodes using heat sinks.
1) We do not accept any liability for this diode recommendation.
Series connection: Two SITOP power supplies for doubling the voltage
Example:
Two single-phase SITOP power supplies with 10 A rated output
current (Order No.: 6EP1334-2BA00) should be connected in
series to increase the voltage. They supply approximately 38 A
dynamically for 200 ms on power-up in the short-circuit case or
e.g. also with loads with a high-capacitance input capacitor that
momentarily act as a short-circuit at the start.
Suitable diodes for V1 and V2 are, for example, of Type SB 340 1)
(Schottky diode in axially wired enclosure DO-201AD with ap-
prox. 5.3 mm diameter and approx. 9.5 mm length of body).
40 V are permissible as the blocking voltage, and the stationary
direct current load capacity IF AV is 3 A. The important dynamic
surge current loading capacity IF SM important in this case is
sufficient for the selected SITOP power supply (more than 100 A
for 8.3 ms). For SITOP power supplies with a low rated output
current, this diode can also be used, but is over-dimensioned.
• Manufacturer: General Instrument
• Distributor: e.g. RS Components, Spoerle
SITOP
L+
M
SITOP
L+
M
G_KT01_EN_00059
Load
Siemens KT10.1 · 2004 14/15
Technical information and configuration
Battery charging, fusing of the
output circuit 24 V DC, selectivity
14
■
Battery charging with SITOP power supplies
The SITOP modular power supplies 5 A to 40 A with stabilized
output voltage that can be set between 24.0 V and 28.8 V supply
a constant output current of approximately 1.2 x rated current
under overload conditions (e.g. a completely discharged 24 V
lead-acid battery). In the case of a V/I characteristic set for
parallel operation, the battery will be charged with a constant
current until approximately 95% of the set SITOP output voltage
has been achieved. The charging current is then continuously
reduced from 1.2 x rated current at 95% of the set voltage to ap-
prox. 0 A or the self-discharge current of the battery at 100% of
the set output voltage, i.e. resistance characteristic in this range.
As reverse voltage protection and polarity reversal protection,
we recommend that a diode suitable for at least 1.2 x rated cur-
rent of the power supply with a blocking voltage of at least 40 V
is connected in series with the + output (anode connected to
+ output of the SITOP modular and cathode connected to posi-
tive pole of the battery).
The output voltage of the power supply must be set at no-load to
the end-of-charge voltage plus the voltage drop at the diode. For
an end-of-charge voltage of e.g. 27.0 V DC (usual at 20 °C to
30 °C battery temperature; in each case, compliance with the
specifications of the battery manufacturer must be observed!)
and 0.8 V voltage drop at the diode, SITOP modular must be set
to 27.8 V during no-load operation.
General note for using SITOP power supplies as a battery
charging unit
When SITOP modular is used as a battery charging unit, the
regulations of VDE 0510 or the relevant national regulations must
be observed and adequate ventilation must be provided. The
SITOP modular power supplies are designed as rack-mounting
units, and protection against electric shock should therefore be
provided by installation in an appropriate housing.
The value recommended by the battery manufacturer must be
set as the end-of-charge voltage (depending on the battery tem-
perature). An ideal temperature for the lead-acid battery is be-
tween +20 and 30 °C and the recommended end-of-charge volt-
age in this case is usually about 27 V.
■
Fusing of 24 V power supply circuits and selectivity
With unstabilized rectifiers (power transformer equipped with
rectifier) the output usually had to be protected with a suitable
fuse so that its rectifier diodes would not fail in the event of an
overload or a short-circuit (this would destroy the DC loads due
to the resulting alternating voltage and lead to serious damage
in most cases).
On the other hand, the stabilized SITOP power supplies comply
with the standard applicable to the electrical equipment of
machines DIN VDE 0113 Part 1, Section 7.2.9 (November 1998)
or EN 60204-1 and are provided with integral electronic short-
circuit protection which automatically protects both the power
supply and the supplied 24 V DC circuits against an excess
current in the event of an overload/short-circuit. A differentiation
must be made between the following three cases with respect to
fusing on the secondary side:
Example 1: No fusing
Fusing the secondary side (24 V DC) for protecting the load cir-
cuits and lines is not required if the respective cross-sections are
selected for the maximum possible output current RMS value.
Depending on the event (short-circuit or overload) this may ei-
ther be the short-circuit RMS value or the current limitation value.
Example SITOP power 10 (Order No.: 6EP1334-2BA00)
• Rated current 10 A
• Current limitation typ. 13 to 15 A
• Short-circuit RMS value < 21 A
The technical specifications usually specify typical values, max-
imum values are approx. 2 A above the typical value. In the ex-
ample here, a maximum possible output current RMS value of
approx. 23 A must therefore be used for line dimensioning.
Example 2: Reduced cross-sections
If smaller cross-sections are used than specified in DIN VDE
0113 Part 1 or EN 60204-1, the associated 24 V load supply lines
must be provided with appropriate line protection (see DIN VDE
0113 Part 1 or EN 60204-1).
It is then unimportant whether the power supply enters current
limiting mode (overload) or delivers the maximum short-circuit
current (low-resistance short-circuit). The load supply line is in
any case protected against an overload by the line protection
matched to the conductor cross-section.
Example 3: Selectivity
In cases where a load which has failed (e.g. because of a short-
circuit) has to be rapidly detected or where it is essential to se-
lectively switch it off before the power supply enters current lim-
iting mode (with current limiting mode, the voltage would also fall
for all remaining 24 V DC loads), there are two possibilities for the
secondary side connection.
• Use of a 4-channel electronic diagnosis module SITOP
select (Order No.: 6EP1961-2BA00), with a current adjust-
able from 2 A to 10 A for each channel
• Series connection of appropriate 24 V DC fuses or circuit-
breakers
The basis for selection of the 24 V DC fuse or circuit-breaker is
the short-circuit current above the rated current which the SITOP
power supplies deliver in the event of a short-circuit during op-
eration (values are specified in the respective technical specifi-
cations under "Output, dynamic V/I on short-circuit during oper-
ation").
It is not easy to calculate the amount of the short-circuit current
flowing into the usually not ideal "short-circuit" and the amount
flowing into the remaining loads. This depends on the type of
overload (high-resistance or low-resistance short-circuit) and
the type of load connected (resistive, inductive and capaci-
tive/electronic loads).
However, it can be assumed with a first approximation in the
average case encountered in practice that the difference of dyn.
V/I minus 50% SITOP rated output current is available for the
immediate tripping of a circuit-breaker within a typical time of
12 ms (with 14 times the rated DC with a circuit-breaker charac-
teristic C acc. to IEC 898 or with 7 times the rated DC with a cir-
cuit-breaker characteristic B or with 5 times the rated DC with a
circuit-breaker characteristic A). Please refer to the following ta-
bles for circuit-breakers appropriate for selected fusing accord-
ing to this assumption.
Siemens KT10.1 · 2004
14/16
Technical information and configuration
Fusing of the output circuit 24 V DC,
selectivity
14
■
List of ordering data and tripping characteristics of single-pole circuit-breakers 5SY4...
acc. to IEC 898/EN 60898 (DIN VDE 0641 Part 11), for use up to 60 V DC (250 V AC, switching capacity 10,000 A)
Rated current Tripping
characteristic
Order No. Range for immediate tripping
< 100 ms for operation with
direct current (alternating
current)
Required DC for
immediate tripping
in < 100 ms
Required DC for
immediate tripping
in approx. 12 ms
1 A Type A 5SY4 101-5 DC: 2 to 5
(AC: 2 to 3) x Irated
2 to 5 A DC 5 A DC
1 A Type C 5SY4 101-7 DC: 5 to 14
(AC: 5 to 10) x Irated
5 to 14 A DC 14 A DC
1.6 A Type A 5SY4 115-5 DC: 2 to 5
(AC: 2 to 3) x Irated
3.2 to 8 A DC 8 A DC
1.6 A Type C 5SY4 115-7 DC: 5 to 14
(AC: 5 to 10) x Irated
8 to 22.4 A DC 22.4 A DC
2 A Type A 5SY4 102-5 DC: 2 to 5
(AC: 2 to 3) x Irated
4 to 10 A DC 10 A DC
2 A Type C 5SY4 102-7 DC: 5 to 14
(AC: 5 to 10) x Irated
10 to 28 A DC 28 A DC
3 A Type A 5SY4 103-5 DC: 2 to 5
(AC: 2 to 3) x Irated
6 to 15 A DC 15 A DC
3 A Type C 5SY4 103-7 DC: 5 to 14
(AC: 5 to 10) x Irated
15 to 42 A DC 42 A DC
4 A Type A 5SY4 104-5 DC: 2 to 5
(AC: 2 to 3) x Irated
8 to 20 A DC 20 A DC
4 A Type C 5SY4 104-7 DC: 5 to 14
(AC: 5 to 10) x Irated
20 to 56 A DC 56 A DC
6 A Type A 5SY4 106-5 DC: 2 to 5
(AC: 2 to 3) x Irated
12 to 30 A DC 30 A DC
6 A Type B 5SY4 106-6 DC: 3 to 7
(AC: 3 to 5) x Irated
18 to 42 A DC 42 A DC
6 A Type C 5SY4 106-7 DC: 5 to 14
(AC: 5 to 10) x Irated
30 to 84 A DC 84 A DC
8 A Type A 5SY4 108-5 DC: 2 to 5
(AC: 2 to 3) x Irated
16 to 40 A DC 40 A DC
8 A Type C 5SY4 108-7 DC: 5 to 14
(AC: 5 to 10) x Irated
40 to 112 A DC 112 A DC
10 A Type A 5SY4 110-5 DC: 2 to 5
(AC: 2 to 3) x Irated
20 to 50 A DC 50 A DC
10 A Type B 5SY4 110-6 DC: 3 to 7
(AC: 3 to 5) x Irated
30 to 70 A DC 70 A DC
10 A Type C 5SY4 110-7 DC: 5 to 14
(AC: 5 to 10) x Irated
50 to 140 A DC 140 A DC
13 A Type A 5SY4 113-5 DC: 2 to 5
(AC: 2 to 3) x Irated
26 to 65 A DC 65 A DC
13 A Type B 5SY4 113-6 DC: 3 to 7
(AC: 3 to 5) x Irated
39 to 91 A DC 91 A DC
13 A Type C 5SY4 113-7 DC: 5 to 14
(AC: 5 to 10) x Irated
65 to 182 A DC 182 A DC
16 A Type A 5SY4 116-5 DC: 2 to 5
(AC: 2 to 3) x Irated
32 to 80 A DC 80 A DC
16 A Type B 5SY4 116-6 DC: 3 to 7
(AC: 3 to 5) x Irated
48 to 112 A DC 112 A DC
16 A Type C 5SY4 116-7 DC: 5 to 14
(AC: 5 to 10) x Irated
80 to 224 A DC 224 A DC
Siemens KT10.1 · 2004 14/17
Technical information and configuration
Fusing of the output circuit 24 V DC,
selectivity
14
■
Ordering data and tripping characteristics of Siemens single-pole circuit-breaker terminals type 8WA1 011-...
Suitable for up to 60 V DC (250 V AC)
The following space-saving circuit-breaker terminals for mere
short-circuit protection can only be snap-mounted on DIN rail
EN 50 022-35x15. They are also available with an auxiliary
switch (1 NO contact and 1 NC contact) and feature higher sen-
sitivity than circuit breakers acc. to IEC 898 (EN 60 898), type B.
Tripping times/ranges are within narrower tolerances than those
of circuit-breakers. When operated with DC, these circuit-
breaker terminals do not trip at currents below the rated current,
from 1.1 times the rated current, the circuit-breaker terminal may
trip after as little as 100 ms.
The circuit-breaker rated value must therefore be above the load
inrush current peak value. In general, however, the first three mil-
liseconds of the load inrush current may be ignored because no
less than 20 to 100 times the rated current is required to trip the
circuit-breaker terminals during this period of time.
• The circuit-breaker terminals already trip after 40 ms at 1.2 to
1.9 times the rated DC.
• The circuit-breaker terminals already trip after 20 ms at 1.7 to
2.6 times the rated DC.
• The circuit-breaker terminals already trip after 12 ms at 2.2 to
3.8 times the rated DC.
For more data, refer to catalog "Industrial switchgear" (Catalog LV 10)
Ordering data and tripping characteristics of Siemens single-pole circuit-breaker terminals type 8WA1 011-...
Rated current DC 2 A 4 A 6 A 10 A
Order No. (without auxiliary switch) 8WA1 011-1SF25 8WA1 011-1SF26 8WA1 011-1SF27 8WA1 011-1SF28
Order No. (with auxiliary switch 1 NO +
1 NC) 8WA1 011-6SF25 8WA1 011-6SF26 8WA1 011-6SF27 8WA1 011-6SF28
Required DC for immediate tripping in
40 ms 2.4 to 3.8 A 4.8 to 7.6 A 7.2 to 11.4 A 12 to 19 A
Required DC for immediate tripping in
20 ms 3.4 to 5.2 A 6.8 to 10.7 A 10.2 to 15.6 A 17 to 26 A
Required DC for immediate tripping in
approx. 12 ms 4.4 to 7.6 A 8.8 to 15.2 A 13.2 to 22.8 A 22 to 38 A
Siemens KT10.1 · 2004
14/18
Technical information and configuration
Fusing of the output circuit 24 V DC,
selectivity
14
■
Miniature circuit-breakers in 24 V DC circuits which are powered by SITOP power supply units
Technical specifications
Type 5 A 10 A
Order No. 6EP1 333-2BA00/
6EP1 333-2AA00 6EP1 334-2BA00/
6EP1 334-2AA00
Input Single-phase Single-phase
Rated voltage Vin rated 120/230 V AC 120/230 V AC
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Rated current Iout rated 5 A 10 A
Dyn. V/I with short-circuit in operation, typ. 20 A for 350 ms 38 A for 200 ms
Tripping of output m.c.b The following are approximately available for selective tripping in practice
SITOP, dyn. V/I - 50% Iout rated, typ. 17.5 A for 350 ms 33 A for 200 ms
CBs to IEC 898, type 5SY4 1.., selectively
trippable in approx. 12 ms 1 A Type A (trips at 5 A DC after typ. 12 ms)
1 A Type C (trips at 14 A DC after typ. 12 ms)
1.6 A Typ A (trips at 8 A DC after typ. 12 ms)
- 1.6 A Type C (trips at 22.4 A DC after typ. 12 ms)
2 A Type A (trips at 10 A DC after typ. 12 ms)
- 2 A Type C (trips at 28 A DC after typ. 12 ms)
3 A Type A (trips at 15 A DC after typ. 12 ms)
- 4 A Type A (trips at 20 A DC after typ. 12 ms)
- 6 A Type A (trips at 30 A DC after typ. 12 ms)
Siemens CB terminals, Type 8WA1 011...,
selectively trippable in approx. 12 ms 2 A Order No. 8WA1 011-1SF25 (trips at 7.6 A DC after max. 12 ms)
4 A Order No. 8WA1 011-1SF26 (trips at 15.2 A DC after max. 12 ms)
- 6 A Order No. 8WA1 011-1SF27 (trips at
22.8 A DC after max. 12 ms)
in 20 ms - 10 A Order No. 8WA1 011-1SF28 (trips at
26 A DC after max. 12 ms)
Siemens KT10.1 · 2004 14/19
Technical information and configuration
Fusing of the output circuit 24 V DC,
selectivity
14
■
Miniature circuit-breakers in 24 V DC circuits which are powered by SITOP power supply units
Technical specifications
Type 5 A 10 A
Order No. 6EP1 333-3BA00 6EP1 334-3BA00
Input Single-phase, two-phase Single-phase, two-phase
Rated voltage Vin rated 120/230-500 V AC 120/230-500 V AC
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Rated current Iout rated 5 A 10 A
Dyn. V/I with short-circuit in operation, typ. 15 A for 25 ms 30 A for 25 ms
Tripping of output m.c.b The following are approximately available for selective tripping in practice
SITOP, dyn. V/I - 50% Iout rated, typ. 12.5 A for 25 ms 25 A for 25 ms
CBs to IEC 898, type 5SY4 1.., selectively
trippable in approx. 12 ms 1 A Type A (trips at 5 A DC after typ. 12 ms)
- 1 A Type C (trips at 14 A DC after typ. 12 ms)
1.6 A Type A (trips at 8 A DC after typ. 12 ms)
- 1.6 A Type C (trips at 22.4 A DC after typ. 12 ms)
2 A Type A (trips at 10 A DC after typ. 12 ms)
- 3 A Type A (trips at 15 A DC after typ. 12 ms)
- 4 A Type A (trips at 20 A DC after typ. 12 ms)
Siemens CB terminals, Type 8WA1 011...,
selectively trippable in approx. 12 ms 2 A Order No. 8WA1 011-1SF25 (trips at 7.6 A DC after max. 12 ms)
- 4 A Order No. 8WA1 011-1SF26 (trips at
15.2 A DC after max. 12 ms)
- 6 A Order No. 8WA1 011-1SF27 (trips at
22.8 A DC after max. 12 ms)
in 20 ms 4 A Order No. 8WA1 011-1SF26 (trips at
10.7 A DC after max. 20 ms) -
Siemens KT10.1 · 2004
14/20
Technical information and configuration
Fusing of the output circuit 24 V DC,
selectivity
14
■
Miniature circuit-breakers in 24 V DC circuits which are powered by SITOP power supply units
Technical specifications
Type 20 A 40 A
Order No. 6EP1 436-2BA00 6EP1 437-2BA10
Input Three-phase Single-phase, two-phase
Rated voltage Vin rated 400-500 V 3 AC 400-500 V AC
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Rated current Iout rated 20 A 40 A
Dyn. V/I with short-circuit in operation, typ. Approx. 30 A constant current 70 A for 600 ms
Tripping of output m.c.b The following are approximately available for selective tripping in practice
SITOP, dyn. V/I - 50% Iout rated, typ. 20 A (without interruption) 50 A for 600 ms
CBs to IEC 898, type 5SY4 1.., selectively
trippable in approx. 12 ms 1 A Type A (trips at 5 A DC after typ. 12 ms)
1 A Type C (trips at 14 A DC after typ. 12 ms)
1.6 A Type A (trips at 8 A DC after typ. 12 ms)
- 1.6 A Type C (trips at 22.4 A DC after typ. 12 ms)
2 A Type A (trips at 10 A DC after typ. 12 ms)
- 2 A Type C (trips at 28 A DC after typ. 12 ms)
3 A Type A (trips at 15 A DC after typ. 12 ms)
- 3 A Type C (trips at 42 A DC after typ. 12 ms)
4 A Type A (trips at 20 A DC after typ. 12 ms)
- 6 A Type A (trips at 30 A DC after typ. 12 ms)
- 6 A Type B (trips at 42 A DC after typ. 12 ms)
- 8 A Type A (trips at 40 A DC after typ. 12 ms)
- 10 A Type A (trips at 50 A DC after typ. 12 ms)
Siemens CB terminals, Type 8WA1 011...,
selectively trippable in approx. 12 ms 2 A Order No. 8WA1 011-1SF25 (trips at 7.6 A DC after max. 12 ms)
4 A Order No. 8WA1 011-1SF26 (trips at 15.2 A DC after max. 12 ms)
- 6 A Order No. 8WA1 011-1SF27 (trips at
22.8 A DC after max. 12 ms)
- 10 A Order No. 8WA1 011-1SF28 (trips at
38 A DC after max. 12 ms)
Siemens KT10.1 · 2004 14/21
Technical information and configuration
Fusing of the output circuit 24 V DC,
selectivity
14
■
Miniature circuit-breakers in 24 V DC circuits which are powered by SITOP power supply units
Technical specifications
Type 20 A 40 A
Order No. 6EP1 436-3BA00
(6EP1 336-3BA00) 6EP1 437-3BA00
(6EP1 337-3BA00)
Input Three-phase
(single-phase) Three-phase
(single-phase)
Rated voltage Vin rated 400-500 V 3 AC
(120/230 V AC)
400-500 V 3 AC
(120/230 V AC)
Output Stabilized, floating direct voltage Stabilized, floating direct voltage
Rated voltage Vout rated 24 V DC 24 V DC
Rated current Iout rated 20 A 40 A
Dyn. V/I with short-circuit in operation, typ. Approx. 60 A for 25 ms Approx. 120 A for 25 ms
Tripping of output m.c.b The following are approximately available for selective tripping in practice
SITOP, dyn. V/I - 50% Iout rated, typ. 50 A for 25 ms 100 A for 25 ms
CBs to IEC 898, type 5SY4 1.., selectively
trippable in approx. 12 ms 1 A Type A (trips at 5 A DC after typ. 12 ms)
1 A Type C (trips at 14 A DC after typ. 12 ms)
1.6 A Type A (trips at 8 A DC after typ. 12 ms)
1.6 A Type C (trips at 22.4 A DC after typ. 12 ms)
2 A Type A (trips at 10 A DC after typ. 12 ms)
2 A Type C (trips at 28 A DC after typ. 12 ms)
3 A Type A (trips at 15 A DC after typ. 12 ms)
3 A Type C (trips at 42 A DC after typ. 12 ms)
4 A Type A (trips at 20 A DC after typ. 12 ms)
- 4 A Type C (trips at 56 A DC after typ. 12 ms)
6 A Type A (trips at 30 A DC after typ. 12 ms)
6 A Type B (trips at 42 A DC after typ. 12 ms)
- 6 A Type C (trips at 84 A DC after typ. 12 ms)
8 A Type B (trips at 40 A DC after typ. 12 ms)
10 A Type A (trips at 50 A DC after typ. 12 ms)
- 10 A Type B (trips at 70 A DC after typ. 12 ms)
- 13 A Type A (trips at 65 A DC after typ. 12 ms)
- 13 A Type B (trips at 91 A DC after typ. 12 ms)
- 16 A Type A (trips at 80 A DC after typ. 12 ms)
- 20 A Type A (trips at 100 A DC after typ. 12 ms)
Siemens CB terminals, Type 8WA1 011...,
selectively trippable in approx. 12 ms 2 A Order No. 8WA1 011-1SF25 (trips at 7.6 A DC after max. 12 ms)
4 A Order No. 8WA1 011-1SF26 (trips at 15.2 A DC after max. 12 ms)
6 A Order No. 8WA1 011-1SF27 (trips at 22.8 A DC after max. 12 ms)
10 A Order No. 8WA1 011-1SF28 (trips at 38 A DC after max. 12 ms)
Siemens KT10.1 · 2004
14/22
Technical information and configuration
Notes
14
Siemens KT10.1 · 2004
75
power
SITOP
M
OK
M
L+
AC
120V
N
PE
L1
2
1345
129.6
G_KT01_EN_00072
15
15/2 SITOP power
Single-, two-, three-phase
15/9 SITOP power
Additional components
15/11 SITOP power
Uninterruptible power supplies
15/13 SITOP power
Alternative voltages
15/14 SITOP power
AS interface power supplies
15/15 LOGO!Power
Dimension drawings
Siemens KT10.1 · 2004
15/2
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6EP1 331-2BA10, 6EP1 731-2BA00
Order No.:
6EP1 331-2BA00
Order No.:
6EP1 331-1SL11, 6ES7 307-1BA00-0AA0
123
L1
N
456
(L+)
(M)
OK
SITOP
power
PE
(M)
91
80
35
6EP1331-2BA00
Q6MH
32
1
22.5
7.5 86.6
G_KT01_EN_00008
ca
50
130
124
125
power
SITOP
6EP1331-2BA00
M
OK
M
L+
AC
120V
N
PE
L1
2
1345
129.6
G_KT01_EN_00069
53 - 53.5
125
50
36
135
1)
1) For 6ES7 307-1BA00-0AA0
Mounting adapter for DIN rail optional
G_KT01_EN_00106
Siemens KT10.1 · 2004 15/3
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6ES7 305-1BA80-0AA0, 6EP1 333-1SL11, 6ES7 307-1EA00-0AA0, 6ES7 307-1EA80-0AA0
Order No.:
6EP1 732-0AA00, 6EP1 332-1SH12, 6EP1 332-1SH22
Order No.:
6EP1 332-1SH31
125
80
36
135
1)
1) For 6ES7 305-1BA80-0AA0, 6ES7 307-1EA00-0AA0, 6ES7 307-1EA80-0AA0
Mounting adapter for DIN rail optional
G_KT01_EN_00107
65
80
135
149
36
164
120
G_KT01_EN_00070
62
160
380
147.4
67.3
G_KT01_EN_00071
Siemens KT10.1 · 2004
15/4
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6EP1 333-3BA00
Order No.:
6EP1 333-2BA00, 6EP1 333-2AA00
Order No.:
6EP1 333-1AL12, 6EA1 334-1AL12
6
100
OUTPUT
INPUT
12345
SITOP
125
70
4
G_KT01_EN_00087
96.5
120.5
124
130
125
75
power
SITOP
M
OK
M
L+
AC
120V
N
PE
L1
2
1345
129.6
G_KT01_EN_00072
53 - 53.5
SITOP power 5
6EP1 333-1AL12
1P
S Q6XXXXXXXX
Made in Austria
LISTED
IND.CONT.EQ
31UB
POWER SUPPLY
DIN 41752
E230.120 G2 4/10Wg
In put: AC120V/2 30V
60/50Hz 2.4A-1.5A
Output: DC24V/5A
MAX.OP.TEMP.60°C
E-Stand 123456
58
SITOP
power 5
123456
130
160
120/230V AC
L1 N
VOLTAGE
SELCTOR
Adjust
24-28.8V
OK24V DC
+ + +
53.9
6.3
G_KT01_EN_00090
Siemens KT10.1 · 2004 15/5
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6EP1 334-3BA00
Order No.:
6EP1 334-2BA00, 6EP1 334-2AA00
6
100
90
OUTPUT
INPUT
12345
SITOP
125
4
G_KT01_EN_00088
96.5
120.5
100
power
SITOP
6EP1334-2AA00
M
OK
M
L+
AC
120V
N
PE
L1
2
1345
129.6
G_KT01_EN_00075
Order No.:
6EP1 334-1SL12, 6ES7 307-1KA01-0AA0, 6EP1 334-1SH01
36
135
125
1)
VOLTAGE
SELECTOR
power 10
SITOP
200 (120 )
2)
2) For 6ES7 307-1KA01-0AA0
Mounting adapter for DIN rail optional
1) 6ES7 307-1KA01-0AA0 and 6EP1 334-1SL12
G_KT01_EN_00108
Siemens KT10.1 · 2004
15/6
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6EP1 334-2CA00
214
110
265
283
140
197
1)
1)
134.6
160.5
158.4
145.4
53.5
133.5
126.5
103.5
22.8
5.4
4 ...10 dia.
5.5 dia.
10.2 dia.
1) Fixing lugs
(only in connection with accessory
connector seal 6EP1 971-2CA00)
G_KT01_EN_00066
8.8
Siemens KT10.1 · 2004 15/7
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6EP1 336-3BA00, 6EP1 436-3BA00
Order No.:
6EP1 337-3BA00, 6EP1 437-3BA00
SHUT DOWN
160
SITOP
INPUT
Jump
(L2)
L1
PE
AC 120/230 V 50/60Hz
++
--
DC ...V/...A
OVERLOAD
OUTPUT
5125
... - ... V
24V OK
N
s
26.87
120.5
6.1
Snap-mounting on DIN rail
DIN EN 50022-35x15/7.5
G_KT01_EN_00156
SHUT DOWN
240
SITOP
INPUT
L1 L2 L3
PE
AC 120/230V 50/60Hz
++
--
DC 24V/40A
24V OK
OVERLOAD
s
OUTPUT
5125
26.87
120.5
6.1
G_KT01_EN_00157
Snap-mounting on DIN rail
DIN EN 50022-35x15/7.5
Siemens KT10.1 · 2004
15/8
Dimension drawings
SITOP power
Single-, two-, three-phase
15
■
Dimensions in mm
Order No.:
6EP1 336-2BA00, 6EP1 434-2BA00, 6EP1 436-2BA00
Order No.:
6EP1 536-2AA00, 6EP1 437-2BA00, 6EP1 437-2BA10
L1 L2 L3
3-ph. 400V - 500V AC PE
SITOP
power
OUTPUT
22,8V - 26,4V
24V DC / 20A
L+ M M
OK
- Adjust +
24V - 26,4V
50 / 60 Hz
INPUT
CAUTION !
READ INSTRUCTION MANUAL !
6EP1 436-2BA00
13254 6
125
280
9
92
G_KT01_EN_00079
53 - 53.5
6.2
L1 L2 L3
3-ph. 400V - 500V AC PE
180
280
SITOP
power
OUTPUT
22,8V - 26,4V
24V DC / 40A
L+ M M
OK
- Adjust +
22,8V - 26,4V
L1 L2 L3
3-ph. 400V - 500V AC PE
50 / 60 Hz
INPUT
CAUTION !
READ INSTRUCTION MANUAL !
13254 6
92
4.9
6.2
53 - 53.5
8.8
G_KT01_EN_00080
Siemens KT10.1 · 2004 15/9
Dimension drawings
SITOP power
Additional components
15
■
Dimensions in mm
Order No.:
6EP1 961-3BA10
Order No.:
6EP1 961-3BA00
!
125
G_KT01_XX_00061
26 116
6
1254
70
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
Q6XX
SITOP
6EP1 961-3BA10
12345
s
120.5
G_KT01_EN_00060a
Order No.:
6EP1 961-3BA20
Order No.:
6EP1 961-2BA00
6
125
70
SITOP
6EP1 961-3BA20
12345
s
120.5
G_KT01_EN_00224
9.5
s
5
max. 94
71,5
80
G_KT01_XX_00225
s
5
max. 94
80
G_KT01_EN_00225
71.5
Siemens KT10.1 · 2004
15/10
Dimension drawings
SITOP power
Accessories
15
■
Dimensions in mm
Order No.:
6EP1 971-1AA01
Order No.:
6EP1 971-2BA00
25
200
236
135
25
50
159
G_KT01_EN_00084
147.5
5.75
50
25
100
320
146
13
30
30
R2
100
25 50
28
10
20
150
90
320
75
75
280
G_KT01_EN_00085
6.2
Siemens KT10.1 · 2004 15/11
Dimension drawings
SITOP power
Uninterruptible power supplies
15
■
Dimensions in mm
Order No.:
6EP1 931-2DC21, 6EP1 931-2DC31, 6EP1 931-2DC41
Order No.:
6EP1 931-2EC21, 6EP1 931-2EC31, 6EP1 931-2EC41
Order No.:
6EP1 931-2FC01
50
133
124
125
1234 5
125
G_KT01_DE_00217
220
20
130
52
60
27.5
G_KT01_EN_00162
power DC UPS Module 40
Siemens KT10.1 · 2004
15/12
Dimension drawings
SITOP power
Uninterruptible power supplies
15
■
Drilling templates
Order No.:
6EP1 935-6MD31
Order No.:
6EP1 935-6MD11
Order No.:
6EP1 935-6ME21
Order No.:
6EP1 935-6MF01
F
bl
+
249
84
Attention!
Charged battery.
Insert fuse F1 on startup
(not before).
After mounting on the rail,
the 2 M4 bolts must be tightened.
Before dismounting from the rail,
the 2 M4 bolts must be loosened.
G_KT01_EN_00004
or
F
bl
+
84
174
Attention!
Charged battery.
Insert fuse F1 on
startup
(not before).
After mounting on the rail,
the 2 M4 bolts must be tightened.
Before dismounting from the rail,
the 2 M4 bolts must be loosened.
or
G_KT01_EN_00005
F
bl
+
101
170
or
Attention!
Charged battery.
Insert fuse F1 on startup
(not before).
15A battery fuse F1 only in combination with
DC UPS module 15 permissible.
25A battery fuse F1 only in combination with
DC UPS module 40 permissible.
G_KT01_EN_00006
F1
or bl
+
237
101
12 Ah
Attention!
Charged battery.
Insert fuse F1 on startup
(not before).
15A battery fuse F1 only in combination with
DC UPS module 15 permissible.
25A battery fuse F1 only in combination with
DC UPS module 40 permissible.
G_KT01_EN_00007
Siemens KT10.1 · 2004 15/13
Dimension drawings
SITOP power
Alternative voltages
15
■
Dimensions in mm
Order No.:
6EP1 353-2BA00, 6EP1 353-0AA00
Order No.:
6EP1 457-3BA00
124
130
125
75
power
SITOP
M
OK
M
L+
AC
120V
N
PE
L1
2
1345
129.6
53 - 53.5
G_KT01_EN_00086
SHUT DOWN
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
Q6XX
240
SITOP
6EP1 457-3BA00
INPUT
L1 L2 L3
PE
3AC 400V - 500V 50/60Hz
++
--
DC 48V/20A
24V OK
OVERLOAD
12345
s
OUTPUT
5125
G_KT01_EN_00158
Snap-mounting on DIN rail
DIN EN 50022-35x15/7.5
26.87
120.5
6.1
Siemens KT10.1 · 2004
15/14
Dimension drawings
SITOP power
AS interface power supplies
15
■
Dimensions in mm
Order No.:
6EP1 354-1AL01
Order No.:
6EP1 632-1AL01
36
135
125
VOLTAGE
SELECTOR
power AS-I
SITOP
200
6EP1 354-1AL01
OK
G_KT01_EN_00108
6EP1 632-1AL01 13254 6
AS-Interface
power RUN
1 PE
2 P24
3 M24
1
1
163
175
224 500
6
52
80
14
1
G_KT01_EN_00138
Fixing screws:
hexagon socket head cap screws
M4x16, 8.8 to DIN 912
P30 RD
M30 BU
Shield BK
P30
M30
Shield
OUTPUT
30 V/2.8 A
INPUT
24 V/4.2 A
Siemens KT10.1 · 2004 15/15
Dimension drawings
LOGO!Power
15
■
Dimensions in mm
Order No.:
6EP1 311-1SH02, 6EP1 321-1SH02, 6EP1 351-1SH02, 6EP1 331-1SH02
Order No.:
6EP1 311-1SH12, 6EP1 322-1SH02, 6EP1 352-1SH02, 6EP1 332-1SH42
Order No.:
6EP1 332-1SH51
56
90
L1 N + +
Input Output
LOGO!Power
72
24V
G_KT01_DE_00082
56
90
L1 N + +
Input Output
LOGO!Power
54
24V
G_KT01_DE_00083
56
90
L1 N ++
Input Output
LOGO!Power
90
24V
G_KT01_DE_00218
Siemens KT10.1 · 2004
15/16
Dimension drawings
Notes
15
Siemens KT10.1 · 2004
16
16/2 SITOP contact persons
16/7 Siemens contacts worldwide
16/8 Service & Support
Information and Ordering
in the Internet and on CD-ROM
16/9 Indexes
16/9 Order No. index
16/10 Subject index
16/11 Customer Support
16/14 Conditions of sale and delivery
Appendix
Siemens KT10.1 · 2004
16/2
Appendix
SITOP contact persons
16
■
in Europe
Austria
Bregenz
Siemens AG
Mr. Madlener
Josef-Huter-Str. 6
6901 Bregenz
Tel +43 (0) 51 707 682
Fax +43 (0) 51 707 522
Email guenter.madlener
@siemens.at
Graz
Siemens AG
Mr. Kröll
Straßganger Str. 315
8054 Graz
Tel +43 (0) 51 707 639 22
Fax +43 (0) 51 707 586 72
Email josef.kroell@siemens.at
Innsbruck
Siemens AG
Mr. Hampel
Siemensstr. 24
6063 Rum bei Innsbruck
Tel +43 (0) 51 707 673 98
Fax +43 (0) 51 707 549 25
Email johann-georg.hampel
@siemens.at
Klagenfurt
Siemens AG
Mr. Weber
Werner v. Siemens Park 1
9020 Klagenfurt
Tel +43 (0) 51 707 642 43
Fax +43 (0) 51 707 544 18
Email richard.r.weber
@siemens.at
Linz
Siemens AG
Mr. Schmidt
Wolfgang-Pauli-Str. 2
4020 Linz
Tel +43 (0) 51 707 652 95
Fax +43 (0) 51 707 596 01
Email erich.e.schmidt
@siemens.at
Salzburg
Siemens AG
Mr. Mariacher
Innsbrucker-Bundesstr. 35
5020 Salzburg
Tel +43 (0) 51 707 663 50
Fax +43 (0) 51 707 532 29
Email josef.mariacher
@siemens.at
Vienna
Siemens AG
Mr. Strasser
Siemensstr. 88-92
1210 Wien
Tel +43 (0) 51 707 237 88
Fax +43 (0) 51 707 539 40
Email josef.strasser
@siemens.at
Belarus
Minsk
Siemens
Mr. Göbecke
Ul. Y. Kupaly 25, Off. 304
220030 Minsk
Tel +375 (17) 210 03 96
Fax +375 (17) 210 03 95
Email alexander.goebecke
@siemens.com
Belgium
Huizingen
Mr. De Coninck
Predslawinka Str. 11-13
3150 Kiew
Tel +32 (2) 536 95 39
Fax +32 (2) 536 23 87
Email geert.de-coninck
@siemens.be
Bosnia-Herzegovina
Sarajevo
Siemens d.o.o.
Mr. Ganic
Dubrovacka 6
71000 Sarajevo
Tel +387 (33) 27 66 41
Fax +387 (33) 27 66 12 79
Email sadudin.ganic
@siemens.ba
Bulgaria
Sofia
Siemens
Mrs. Boykova
Nikola Vaptzarov Boulevard
1407 Sofia
Tel +359 (2) 965 96 24
Fax +359 (2) 965 96 62
Email simatic.service
@siemens.bg
Croatia
Zagreb
Mrs. Ilic
Heinzelova 70a
10000 Zagreb
Tel +385 (1) 6105 337
Fax +385 (1) 6105 621
Email ivana.ilic@siemens.com
Czech Republic
Brno
Siemens s.r.o.
Mr. Bocek
Technicka 15
61600 Brno
Tel +420 (5) 4119 1731
Fax +420 (5) 4119 1749
Email petr.bocek@siemens.com
Prague
Mr. Pömmerl
Evropská 33a
Praha 6
Tel +420 (2) 3303 2410
Fax +420 (2) 3303 2492
Email werner.poemmerl
@siemens.com
Denmark
Kopenhagen
Mr. Limkilde
Borupvang 3
2750 Ballerup
Tel +45 4477 4883
Fax +45 4477 4002
Email llk@siemens.dk
Estonia
Tallinn
AS Siemens Automation and
Drives
Mr. Ristoja
Pärnu mnt. 139 c
11317 Tallinn
Tel +372 630 47 51
Fax +372 630 47 31
Email joel.ristoja@siemens.com
Finland
Helsinki
Siemens Oy Automation and
Drives
Mr. Leppala
Majurinkatu 6
02600 Espoo
Tel +358 10 511 3463
Fax +358 10 511 3656
Email ari.leppala@siemens.com
France
Paris
Mr. Rouault
39-47, Boulevard Ornano
93527 Saint-Denis CEDEX 2
Tel +33 (1) 4922 9309
Fax +33 (1) 4922 3951
Email jean-marie.rouault
@siemens.fr
Germany
Aachen
Siemens AG
Mr. Schauenberg
Franz-Geuer-Str. 10
50823 Köln
Tel +49 (221) 576 2536
Fax +49 (221) 576 2921
Email frank.schauenberg
@siemens.com
Augsburg
Siemens AG
Mr. Greis
Richard-Strauss-Str. 76
81679 München
Tel +49 (89) 9221 3877
Fax +49 (89) 9221 1738
Email wolfgang.greis
@siemens.com
Bayreuth
Siemens AG
Mr. Fiedler
Von-der-Tann-Str. 30
90439 Nürnberg
Tel +49 (911) 654 3413
Fax +49 (911) 654 3596
Email wolfram.fiedler
@siemens.com
Berlin
Siemens AG
Mr. Förster
Nonnendammallee 72
13629 Berlin
Tel +49 (30) 386 32 303
Fax +49 (30) 386 32 543
Email martin.foerster
@siemens.com
Bielefeld
Siemens AG
Mr. Knauth
Frankfurter Str. 3d
38112 Braunschweig
Tel +49 (531) 2712 314
Fax +49 (531) 2712 416
Email bernd.knauth
@siemens.com
Braunschweig
Siemens AG
Mr. Knauth
Frankfurter Str. 3d
38112 Braunschweig
Tel +49 (531) 2712 314
Fax +49 (531) 2712 416
Email bernd.knauth
@siemens.com
Bremen
Siemens AG
Mr. Kröger
Universitätsallee 16
28359 Bremen
Tel +49 (421) 364 2185
Fax +49 (421) 364 2249
Email helmut.kroeger
@siemens.com
Chemnitz
Siemens AG
Mr. Förster
Nonnendammallee 72
13629 Berlin
Tel +49 (30) 386 32 303
Fax +49 (30) 386 32 543
Email martin.foerster
@siemens.com
Dresden
Siemens AG
Mr. Förster
Nonnendammallee 72
13629 Berlin
Tel +49 (30) 386 32 303
Fax +49 (30) 386 32 543
Email martin.foerster
@siemens.com
Düsseldorf
Siemens AG
Mr. Schauenberg
Franz-Geuer-Str. 10
50823 Köln
Tel +49 (221) 576 2536
Fax +49 (221) 576 2921
Email frank.schauenberg
@siemens.com
Erfurt
Siemens AG
Mr. Förster
Nonnendammallee 72
13629 Berlin
Tel +49 (30) 386 32 303
Fax +49 (30) 386 32 543
Email martin.foerster
@siemens.com
Essen
Siemens AG
Mr. Poschmann
Kruppstr. 16
45128 Essen
Tel +49 (201) 816 2148
Fax +49 (201) 816 3621
Email rolf.poschmann
@siemens.com
Frankfurt
Siemens AG
Mr. Wulle
Dynamostr. 4
68165 Mannheim
Tel +49 (621) 465 2661
Fax +49 (621) 465 2747
Email thomas.wulle
@siemens.com
Freiburg
Siemens AG
Mr. Röder
Weissacher Str. 11
70499 Stuttgart
Tel +49 (711) 137 4059
Fax +49 (711) 137 2070
Email bernd.roeder
@siemens.com
Siemens KT10.1 · 2004 16/3
Appendix
SITOP contact persons
16
■
in Europe (continued)
Hamburg
Siemens AG
Mr. Kröger
Universitätsallee 16
28359 Bremen
Tel +49 (421) 364 2185
Fax +49 (421) 364 2249
Email helmut.kroeger
@siemens.com
Hannover
Siemens AG
Mr. Knauth
Frankfurter Str. 3d
38112 Braunschweig
Tel +49 (531) 2712 314
Fax +49 (531) 2712 416
Email bernd.knauth
@siemens.com
Heilbronn
Siemens AG
Mr. Röder
Weissacher Str. 11
70499 Stuttgart
Tel +49 (711) 137-4059
Fax +49 (711) 137-2070
Email bernd.roeder
@siemens.com
Karlsruhe
Siemens AG
Mr. Wulle
Dynamostr. 4
68165 Mannheim
Tel +49 (621) 465 2661
Fax +49 (621) 465 2747
Email thomas.wulle
@siemens.com
Kassel
Siemens AG
Mr. Knauth
Frankfurter Str. 3d
38112 Braunschweig
Tel +49 (531) 2712 314
Fax +49 (531) 2712 416
Email bernd.knauth
@siemens.com
Kempten
Siemens AG
Mr. Greis
Richard-Strauss-Str. 76
81679 München
Tel +49 (89) 9221 3877
Fax +49 (89) 9221 1738
Email wolfgang.greis
@siemens.com
Kiel
Siemens AG
Mr. Kröger
Universitätsallee 16
28359 Bremen
Tel +49 (421) 364 2185
Fax +49 (421) 364 2249
Email helmut.kroeger
@siemens.com
Koblenz
Siemens AG
Mr. Schauenberg
Franz-Geuer-Str. 10
50823 Köln
Tel +49 (221) 576 2536
Fax +49 (221) 576 2921
Email frank.schauenberg
@siemens.com
Cologne
Siemens AG
Mr. Schauenberg
Franz-Geuer-Str. 10
50823 Köln
Tel +49 (221) 576 2536
Fax +49 (221) 576 2921
Email frank.schauenberg
@siemens.com
Konstanz
Siemens AG
Mr. Röder
Weissacher Str. 11
70499 Stuttgart
Tel +49 (711) 137 4059
Fax +49 (711) 137 2070
Email bernd.roeder
@siemens.com
Leipzig
Siemens AG
Mr. Förster
Nonnendammallee 72
13629 Berlin
Tel +49 (30) 386 32 303
Fax +49 (30) 386 32 543
Email martin.foerster
@siemens.com
Magdeburg
Siemens AG
Mr. Knauth
Frankfurter Str. 3d
38112 Braunschweig
Tel +49 (531) 2712 314
Fax +49 (531) 2712 416
Email bernd.knauth
@siemens.com
Mannheim
Siemens AG
Mr. Wulle
Dynamostr. 4
68165 Mannheim
Tel +49 (621) 465 2661
Fax +49 (621) 465 2747
Email thomas.wulle
@siemens.com
Munich
Siemens AG
Mr. Greis
Richard-Strauss-Str. 76
81679 München
Tel +49 (89) 9221 3877
Fax +49 (89) 9221 1738
Email wolfgang.greis
@siemens.com
Münster
Siemens AG
Mr. Poschmann
Kruppstr. 16
45128 Essen
Tel +49 (201) 816 2148
Fax +49 (201) 816 3621
Email rolf.poschmann
@siemens.com
Nürnberg
Siemens AG
Mr. Fiedler
Von-der-Tann-Str. 30
90439 Nürnberg
Tel +49 (911) 654 3413
Fax +49 (911) 654 3596
Email wolfram.fiedler
@siemens.com
Osnabrück
Siemens AG
Mr. Poschmann
Kruppstr. 16
45128 Essen
Tel +49 (201) 816 2148
Fax +49 (201) 816 3621
Email rolf.poschmann
@siemens.com
Regensburg
Siemens AG
Mr. Fiedler
Von-der-Tann-Str. 30
90439 Nürnberg
Tel +49 (911) 654 3413
Fax +49 (911) 654 3596
Email wolfram.fiedler
@siemens.com
Rostock
Siemens AG
Mr. Kröger
Universitätsallee 16
28359 Bremen
Tel +49 (421) 364 2185
Fax +49 (421) 364 2249
Email helmut.kroeger
@siemens.com
Saarbrücken
Siemens AG
Mr. Wulle
Dynamostr. 4
68165 Mannheim
Tel +49 (621) 465 2661
Fax +49 (621) 465 2747
Email thomas.wulle
@siemens.com
Siegen
Siemens AG
Mr. Schauenberg
Franz-Geuer-Str. 10
50823 Köln
Tel +49 (221) 576 2536
Fax +49 (221) 576 2921
Email frank.schauenberg
@siemens.com
Stuttgart
Siemens AG
Mr. Röder
Weissacher Str. 11
70499 Stuttgart
Tel +49 (711) 137 4059
Fax +49 (711) 137 2070
Email bernd.roeder
@siemens.com
Trier
Siemens AG
Mr. Wulle
Dynamostr. 4
68165 Mannheim
Tel +49 (621) 465 2661
Fax +49 (621) 465 2747
Email thomas.wulle
@siemens.com
Ulm
Siemens AG
Mr. Röder
Weissacher Str. 11
70499 Stuttgart
Tel +49 (711) 137 4059
Fax +49 (711) 137 2070
Email bernd.roeder
@siemens.com
Weingarten
Siemens AG
Mr. Röder
Weissacher Str. 11
70499 Stuttgart
Tel +49 (711) 137 4059
Fax +49 (711) 137 2070
Email bernd.roeder
@siemens.com
Wetzlar
Siemens AG
Mr. Wulle
Dynamostr. 4
68165 Mannheim
Tel +49 (621) 465 2661
Fax +49 (621) 465 2747
Email thomas.wulle
@siemens.com
Würzburg
Siemens AG
Mr. Fiedler
Von-der-Tann-Str. 30
90439 Nürnberg
Tel +49 (911) 654 3413
Fax +49 (911) 654 3596
Email wolfram.fiedler
@siemens.com
Wuppertal
Siemens AG
Mr. Poschmann
Kruppstr. 16
45128 Essen
Tel +49 (201) 816 2148
Fax +49 (201) 816 3621
Email rolf.poschmann
@siemens.com
Great Britain
Manchester
Mr. Mackrory
Sir William Siemens House/
Princess Road
Manchester M20 2UR
Tel +44 (161) 446 6400
Fax +44 (161) 446 6201
Email john. mackrory
@siemens.com
Greece
Athens
Siemens A.E.
Mrs. Antoniou
Artemidos 8
15110 Amaroussio/Athen
Tel +30 (1) 6864 534
Fax +30 (1) 6864 299
Email konstantina.antoniou
@siemens.gr
Hungary
Budapest
Mr. Solt
Gizella ut 51-57
1143 Budapest
Tel +36 (1) 471 1717
Fax +36 (1) 471 1704
Email attila.solt@siemens.hu
Ireland
Dublin
Siemens Ltd.
Mr. Feeley
Leeson Close
2 Dublin
Tel +353 (1) 216 2441
Fax +353 (1) 216 2499
Email martin.feeley
@siemens.com
Siemens KT10.1 · 2004
16/4
Appendix
SITOP contact persons
16
■
in Europe (continued)
Italy
Bari
Mr. Gabellone
Via Lucarelli, 10/b
70124 Bari
Tel +39 (080) 50 24068
Email luca.gabellone
@siemens.it
Bologna
Mr. Tosatti
Via del Gomito, 1
40127 Bologna
Tel +39 (051) 63 84509
Email davide.tosatti@siemens.it
Bologna
Mr. Forghieri
Via del Gomito, 1
40127 Bologna
Tel +39 (051) 63 84608
Email mauro.forghieri
@siemens.it
Florence
Mr. Vessio
Via Odorico da Pordenone, 26
50127 Firenze
Tel +39 (055) 3392 201
Email domenico.vessio
@siemens.it
Milan
Mr. Bischetti
Viale Piero e Alberto Pirelli 10
20126 Milano
Tel +39 (02) 6676 3321
Fax armando.bischetti
@siemens.it
Milan
Mr. Berti
Viale Piero e Alberto Pirelli 10
20126 Milano
Tel +39 (02) 6676 2836
Email gualtiero.berti
@siemens.it
Milan
Mr. Gaspari
Viale Piero e Alberto Pirelli 10
20126 Milano
Tel +39 (02) 6676 2067
Email adolfo.gaspari
@siemens.it
Naples
Mr. De Sio
Via G. Quagliarello, 35/E
80146 Napoli
Tel +39 (081) 5454237
Email maurizio.desio
@siemens.it
Padova
Mr. Millevoi
Viale dell’Industria, 19
35129 Padova
Tel +39 (049) 8291336
Email piero.millevoi@siemens.it
Padova
Mr. Maffioli
Viale dell’Industria, 19
35129 Padova
Tel +39 (049) 8291359
Email andrea.maffioli
@siemens.it
Rome
Mr. D Innocenti
Via Laurentina 455
142 Roma
Tel +39 (06) 59692 285
Email dario.dinnocenti
@siemens.it
Torino
Mr. Montoli
Via Pio VII, 127
10127 Torino
Tel +39 (011) 6173 275
Email daniele.montoli
@siemens.it
Latvia
Riga
Siemens SIA
Mr. Tumpelis
Vilandes iela 3
1010 Riga
Tel +371 (701) 55 18
Fax +371 (701) 55 01
Email ugis.tumpelis
@siemens.com
Lithuania
Vilnius
Siemens UAB
Mr. Laurinaitis
V. Kudirkos g.6
2009 Vilnius
Tel +370 (2) 39 1515
Fax +370 (2) 39 1501
Email rimas.laurinaitis
@siemens.com
Luxembourg
Luxembourg
Siemens S.A.
Mr. Koch
20, rue des Peupliers
2328 Luxembourg-Hamm
Tel +352 (43) 8 43-403
Fax +352 (43) 8 43-449
Email edmond.koch
@siemens.lu
Netherlands
The Hague
Siemens Nederland N.V.
Mr. Nieuwstraten
Prinses Beatrixlaan 800
2595 BN The Hague
Tel +31 70 333 32 74
Fax +31 70 333 38 85
Email anton.nieuwstraten
@siemens.nl
Norway
Oslo
Mr. Otterstad
Østre Aker vei 90
0518 Oslo
Tel +47 2263 4164
Fax +47 2263 3390
Email dag.otterstad
@siemens.no
Poland
Gdansk Sales North
Siemens Sp.z o.o.
Mr. Skicki
ul. Batorego 28-32
Gdansk Sales North
Tel +48 (58) 785 8490
Fax +48 (58) 785 8499
Email andrzej.skicki
@siemens.com
Katowice Sales South
Siemens Sp.z o.o.
Mr. Mezydlo
ul. Dolnych Walow 7
Katowice Sales South
Tel +48 (32) 208 4130
Fax +48 (32) 208 4139
Email tomasz.mezydlo
@siemens.com
Poznan Sales West
Siemens Sp.z o.o.
Mr. Kaysiewicz
ul. Romana Maya 1
Poznan Sales West
Tel +48 (61) 650 2823
Fax +48 (61) 650 2824
Email maciej.kaysiewicz
@siemens.com
Warsaw Sales East
Siemens Sp.z o.o.
Mr. Zielinski
ul. Zupnicza 11
Warszawa Sales East
Tel +48 (22) 870 9862
Fax +48 (22) 870 9119
Email andrzej.zielinski
@siemens.pl
Warsaw
Siemens Sp.z o.o.
Mr. Ciuk
ul. Zupnicza 11
3821 Warszawa
Tel +48 (22) 870 9145
Fax +48 (22) 870 9169
Email andrzej.ciuk
@siemens.com
Portugal
Amadora
Siemens S. A.
Mr. Filipe
Rua Irmãos de Siemens, 1
2720093 Amadora
Tel +351 (21) 417 8838
Fax +351 (21) 417 8050
Email sergio.filipe
@lis1.siemens.pt
Romania
Bukarest
Siemens S.R.L.
Mr. Razvan
Calea Pleavei Nr. 139,
Corp C, sector 6
RO 77131 Bucuresti
Tel +40 2120 77 469
Fax +40 2120 77 462
Email razvan.ioachim
@siemens.com
Russia
Moscow
Mr. Iwanow
Ul. Malaja Kaluzhskaja, 17/19
117071 Moscow
Tel +7 (095) 737 2492
Fax +7 (095) 737 2483
Email pawel.iwanow
@siemens.com
Slovakia
Bratislava
Siemens s.r.o.
Mr. Patoprsty
Stromova 9
83796 Bratislava
Tel +421 (2) 5968-2426
Fax +421 (2) 5968 5240
Email radomir.patoprsty
@siemens.sk
Slovenia
Ljubljana
Siemens d.o.o.
Mr. Mlinsek
Dunajska 22
1511 Ljubljana
Tel +386 (1) 4746-152
Fax +386 (1) 4746-138
Email matjaz.mlinsek
@siemens.si
Spain
Madrid
Mr. Ramón Romero
Ronda de Europa, 5
Tres Cantos (Madrid)
Tel +34 (91) 514 4761
Fax +34 (91) 514 7019
Email pssitop@ssa.siemens.es
Sweden
Stockholm
Siemens AB
Mr. Naglitsch
Johanneslundsvägen 12-14
Upplands Väsby
Tel +46 (8) 728 1872
Fax +46 (8) 728 1290
Email peter.naglitsch
@siemens.se
Switzerland
Basel
Siemens Schweiz AG
Mr. Gysin
Viaduktstr. 40
4051 Basel
Tel +41 (0) 848 822 844
Fax +41 (0) 848 822 876
Email rudolf.gysin
@siemens.com
Lausanne
Siemens Suisse SA
Mr. Gysin
Avenue des Baumettes 5
1020 Renens
Tel +41 (0) 848 822 844
Fax +41 (0) 848 822 876
Email rudolf.gysin
@siemens.com
Zürich
Siemens Schweiz AG
Mr. Gysin
Freilagerstr. 40
8047 Zürich
Tel +41 (0) 848 822 844
Fax +41 (0) 848 822 876
Email rudolf.gysin
@siemens.com
Turkey
Istanbul
Siemens Sanayi ve Ticaret A.S.,
Istanbul
Mrs. Ýnan
Yakacik Yolu No. 111
81430 Kartal-Istanbul
Tel +90 (216) 459 3706
Fax +90 (216) 459 3079
Email sevtap.inan
@siemens.com.tr
Siemens KT10.1 · 2004 16/5
Appendix
SITOP contact persons
16
■
in Europe (continued)
■
outside Europe
Ukraine
Kiew
Siemens AG
Mr. Fadejew
Uliza Worowskowo 27
252054 Kiew 54
Tel +380 (44) 201-2461
Fax +380 (44) 201-2466
Email wladimir.fadejew
@siemens.com
Yugoslavia
Belgrade
Siemens d.o.o., Belgrad
Mr. Rajic
Knez Mihailova 30
11000 Belgrad
Tel +381 (11) 3070 184
Fax +381 (11) 3070 050
Email milan.rajic@siemens.com
Africa
Algeria
Algier
Siemens Algérie S.A.R.L.
Mr. Rabah Chaoui
29, rue des pins
16035 Algier
Tel +213 21 60 37 65
Tel +213 21 60 72 07
Fax +213 21 48 09 79
Email rabah.chaoui
@siemens.com
Cote d’Ivoire
Abidjan
Semen
Mr. Hellal
Atelier Z.I. Vridi
Rue des Petroliers
15 B.P. 1062
Abidjan 15, Semen
Tel +225 21 27 16 75 (46 57)
Fax +225 21 27 10 21
Email philippehellal@aviso.ci
Egypt
Cairo
Siemens Ltd.
Mr. El-Bassyouni
55 A & B, El Nakhil and
El Aenab Street
Cairo - Mohandessin, NME
Tel +20 2 33 33 6 12
Fax +20 2 33 33 6 07
Email tamer.bassyouni
@siemens.com
Samouha-Alexandria
Siemens Limites
Mr. Lotfy
27, Victor Emmanuel Street
Samouha-Alexandria
Tel +20 (3) 4251007
Fax +20 (3) 4251009
Email mina.lotfy@siemens.com
Kenya
Nairobi
International Energy Technik Ltd.
Mr. Pillay
P.O. Box 46215
Unit 90, The Alpha Centre
Mombasa Road
Nairobi
Tel +254 2 35 1082
Fax +254 2 35 0469
Email rajesh.pillay@iet.co.ke
Morocco
Casablanca
Siemens Marokko S.A.
Immeuble Siemens
Mr. Mostafa Bazokar
km 1 Route de Rabat Aïn-Sebâa
20250 Casablanca
Tel +212 22 66 92 59 (92 28)
Fax +212 22 34 01 51
Email mostafa.bazokar
@siemens.com
South Africa
Johannesburg
Siemens SA
Control and Instrumentation
Siemens Park Midrand
Mr. Venter
300 Janadel Avenue
Halfway House 1685
Johannesburg - Südafrika
Tel +27 (011) 652 36 88
Fax +27 (011) 652 36 97
Email stephen.venter
@siemens.com
Tun esia
Tun i
Faze Service
Mr. Fantar
Immeuble Nour El Bouhaira E. B.
Rue du Lac Turkana
Les Berges du Lac
1053 Tuni
Tel +216 71 964 266
Fax +216 71 964 265
Email afif.fantar@faze.com.tn
America
Argentina
Buenos Aires
Siemens S.A.
Mr. Abenante
Calle 122 (ex Gral. Roca) 4785,
Ruta 8, km 18 - Casilla de
Correo 32
RA-B1653 JXA San Martin
Prov. de Buenos Aires
Tel +54 11 4738 7341
Fax +54 11 4738 7271
Email matias.abenante
@siemens.com
Brazil
São Paulo
Siemens Ltd.
Mr. Marchesan
Rua Coronel Bento Bicudo,
111 - Lapa
05069 900 São Paulo - SP
Tel +55 11 3833 4115
Fax +55 11 3833 4183
Email ricardo.marchesan
@siemens.com
Canada
Ontario
Siemens Canada Ltd.
Mr. Udayan
80 Walker Drive
Brampton, ON L6T 4H6
Tel +1 905 819 5800 (2470)
Fax +1 905 819 5719
Email udayan.pandya
@siemens.com
Chile
Santiago de Chile
Siemens SA Mercosur
Mr. Gorenberg
Alameda 194, p°3 - Santiago
Santiago de Chile
Tel +56 2 361 4283
Fax +56 2 361 4293
Email andres.gorenberg
@siemens.com
Columbia
Santafé de Bogotá D.C.
Siemens S.A.
Mr. Mejia
Carrera 65 No. 11-83
Santafé de Bogotá D.C.
Tel +57 (1) 4253 710
Fax +57 (1) 2942 600
Email jorge.mejia
@siemens.com
Costa Rica
San José
Siemens S.A. San José
Mr. Blanco
La Uruca
Apartado: 10022-1000 S.J.
San José, Costa Rica
Tel +506 (287) 5251
Fax +506 (287) 5295
Email sergio.blanco
@siemens.com.mx
El Salvador
San Salvador
Mr. Callejas
Antiguo Cuscatlán,
Apartado 1525
01 137 San Salvador
Tel +503 278 3333
Fax +503 278 3334
Email victor.callejas
@siemens.com
Guatemala
Ciudad de Guatemala
Siemens S.A.
Mr. Godoy
2a. Calle 6-76, Zona 10
Ciudad de Guatemala
Tel +502 379 2333
Fax +502 379 2318
Email miguel.godoy
@siemens.com
Mexico
Colonial Industrial Vallejo
Siemens SA
Mr. Quintana
Poniente 116 No. 560
02300 Méxiko, D.F.
Tel +525 55 328 20 00 - 3330
Fax +525 55 328 20 00 - 2097
Email edgar.quintana
@siemens.com
Colonial Industrial Vallejo
Siemens SA
Mr. Sánchez
Poniente 116 No. 560
Colonial Industrial Vallejo
Tel +52 (5) 328-2112
Fax +52 (5) 328-2097
Email gregorio.sanchez
@siemens.com
Peru
Lima
Siemens
Mr. Balarezo
Av. Domingo Orué 971, Surquillo
Lima
Tel +51 (1) 2150030 (4354)
Fax +51 (1) 42 19 292
Email jesus.balarezo
@siemens.com
USA
Norcross
Siemens SE&A
Mr. Bronzel
5300 Triangle Parkway
30092-2538 Norcross, GA
Tel +001 (770) 871 3946
Fax +001 (770) 871 3996
Email kai-uwe.bronzel
@siemens.com
Venezuela
Caracas
Siemens s.a.
Mr. Cavada
Av. Don Diego Disneros
(1010-A-Aptdo. 3616) =Pf
Urbanización, Los Ruices
Caracas 1071
Tel +58 (2) 203 8436
Fax +58 (2) 203 8523
Email jesus.cavada
@siemens.com
Siemens KT10.1 · 2004
16/6
Appendix
SITOP contact persons
16
■
outside Europe (continued)
Further information on contact person’s adresses can be found in
the Internet under
http//www.siemens.com/automation/partner
Asia
China
Beijing
Siemens Limited
Mr. Shi
7, Wangjing Zhonghuan Nanlu
100015 Beijing
Tel
+86 (10) 6472 1888 (3374)
Fax +86 (10) 6473 9213
Email lin.shi@siemens.com
Beijing
Siemens Limited
Mr. Deng
7, Wangjing Zhonghuan Nanlu
100015 Beijing
Tel
+86 (10) 6472 1888 (3903)
Fax +86 (10) 6473 9213
Email xu.deng@siemens.com
Hong Kong
Siemens Ltd.
Mr. Lam
58/F, Central Plaza,
18 Harbour Road
Wanchai, Hong Kong
Tel +86 (852) 2583 3228
Fax +86 (852) 2824 9196
Email jacky.lam@siemens.com
India
Thane
Siemens Limited
Mr. Karmile
Kalwa Works, Thane Belapur
Road
400 601 Thane (Maharashtra)
Indonesia
Jakarta
P.T. Siemens Indonesia
Mr. Ansori
Jalan Jendral Ahmad Yani
Kav. B 67-68
Pulo Mas
13210 Jakarta
Tel +62 (21) 4729-348
Fax +62 (21) 4729-300
Email ato.ansori@siemens.com
Iran
Theran
Siemens Sherkate Sahami (Khass)
Mr. Jashni
Avenue Ayatollah Taleghani 32
15936 Theran
Tel +9821 6142234
Fax +9821 6460615
Email yousef.jashni
@siemens.com
Israel
Tel-Aviv
ARDAN
Production & Industrial
Control Ltd.
Mr. Bauer
32, Habanay Street
Holon 58856
Tel +972 (3) 6 50 70 00
Fax +972 (3) 5 58 13 11
Email bauer@ardan-pic.co.il
Japan
Shinagawa-ku, Tokyo
Siemens K.K.
Mr. Ishida
20-14, Higashi-Gotanda 3-
chome
141-8614 Shinagawa-ku, Tokyo
Tel +81 (3) 5423 8594
Fax +81 (3) 5423 8734
Email toshikazu.ishida
@siemens.com
Jordan
Amman
F.A. Kettaneh & Co.Ltd.
Mr. Rami
Al Quds Street, P.O. Box 485
11118 Amman
Tel +962 (6) 439 8642/7173
Fax +962 (6) 439 2582
Email al-naqa.rami
@kettaneh.com.jo
Lebanon
Mar-Mikhael-Beirut
Kettaneh S.A.
Mr. Markarian
Nahr Street
Mar-Mikhael- Beirut
Tel 00961 1 444560/3
Fax 00961 1 4446284
Email avedis.markarian
@kettaneh.com
Kazakhstan
Almaty
Siemens TOO
Mr. Kokoulin
20, Zharokov St.
480008 Almaty
Tel +73 272 597 828
Fax +73 272 583 700
Email andrej.kokoulin
@siemens.com
Kuwait
Sharq
Siemens
Mr. Chhabra
Jaber Al-Mubarak Street, Block 4
Sharq, Kuwait
Tel 965 241 8888
Fax 965 246 3222
Email naukhez.arslan
@siemens.com
Korea
Seoul
Siemens Limited
Mr. Song
726, Asia Building 10th floor
Yeoksam-dong, Kangnam-gu
135 925 Seoul
Tel +82 (2) 3420 4897
Fax +82 (2) 527 7785
Email songss@siemens.com
Malaysia
Kuala Lumpur
Mrs. Leong
11 section 16/11,
Jalan Damansara
46350 Petaling Jaya,
Selangor Darul Ehsan
Tel +60 (3) 7952 5363
Fax +60 (3) 7955 2282
Email therese.leong
@siemens.com
Pakistan
Karachi
Siemens Pakistan
Engineering Co. Ltd.
Mr. Naukhez
B-72, Estate Avenue, S.I.T.E.
75700 Karachi
Tel
+92 (21) 2574 910 19-4387
Fax +92 (21) 256 3563
Email naukhez.arslan@
siemens.com
Philippines
Makati City
Siemens Inc.
Mr. Salud
169 H.V. De la Costa Street,
Salcedo Village
1227 Makati City
Tel +63 (2) 814 9678
Fax +63 (2) 814 9894
Email bernard.salud
@siemens.com
Saudi Arabia
Jeddah
Siemens Ltd.
Mr. Vhora
Baladia/Binzager Street
Jeddah 21412
Tel +966 (2) 661-4444 (2069)
Fax +966 (2) 661-4444 (1500)
Email abdulhafiz.vhora
@siemens.com
Thailand
Bangkok
Siemens
Mr. Somchai
2922/283 New Petchburi Road,
Bangkapi, Huay Kwang
10310 Bangkok
Tel +66 2715 4850
Fax +66 2715 4841
Email somchaij@siemens.com
Taiwan
Taipei
Siemens
Mr. Gu
3, Yuan Qu Street,
Nan Gang District
115 Taipei
Tel +886 (2) 2652 8888
Fax +886 (2) 2652 8948
Email ginfu.gu
@siemens.com
Uzbekistan
Taschkent
Siemens AG
Mr. Dobrev
K. Yarmatov Str. 6
Taschkent
Tel +998 (71) 120 6403
Fax +998 (71) 120 6402
Email evgeniy.dobrev
@siemens.com
Vietnam
Hanoi
Siemens AG
Mr. Phuong
239 Xuan Thuy Road,
Cau Giay District
Hanoi
Tel +84 (4) 8334 400
Fax +84 (4) 8334 371
Email nguyen-ngoc.phuong
@siemens.com
Australia
Bayswater Victoria
Siemens Limited
Mr. Avellino
885 Mountain Highway
3153 Bayswater Victoria
Tel +61 3 9721 7592
Fax +61 3 9721 7630
Email mark.avellino
@siemens.com
Siemens KT10.1 · 2004 16/7
Appendix
Siemens contacts worldwide
16
At
www.siemens.com/automation/partner
you can find details of Siemens contact partners worldwide re-
sponsible for particular technologies.
You can obtain in most cases a contact partner for
• Technical Support,
• Spare parts/repairs,
• Service,
• Training,
• Sales or
• Consultation/engineering.
You start by selecting a
• Country,
•Product or
•Sector.
By further specifying the remaining criteria you will find exactly
the right contact partner with his/her respective expertise.
Siemens KT10.1 · 2004
16/8
Appendix
Information and Ordering
in the Internet and on CD-ROM
Service & Support
16
■
A&D in the WWW
A detailed knowledge of the range of products and services
available is essential when planning and configuring automation
systems. It goes without saying that this information must always
be fully up-to-date.
The Siemens Automation and Drives Group (A&D) has therefore
built up a comprehensive range of information in the World Wide
Web, which offers quick and easy access to all data required.
Under the address
http://www.siemens.com/automation
you will find everything you need to know about products, sys-
tems and services.
■
Product Selection Using the Interactive Catalog
Detailed information together with convenient interactive func-
tions:
The interactive catalog CA 01 covers more than 80,000 products
and thus provides a full summary of the Siemens Automation
and Drives product base.
Here you will find everything that you need to solve tasks in the
fields of automation, switchgear, installation and drives.
All information is linked into a user interface which is easy to
work with and intuitive.
After selecting the product of your choice you can order at the
press of a button, by fax or by online link.
Information on the interactive catalog CA 01can be found in the
Internet under
http://www.siemens.com/automation/ca01
or on CD-ROM or DVD.
■
Easy Shopping with the A&D Mall
The A&D Mall is the virtual department store of Siemens AG in
the Internet. Here you have access to a huge range of products
presented in electronic catalogs in an informative and attractive
way.
Data transfer via EDIFACT allows the whole procedure from se-
lection through ordering to tracking of the order to be carried out
online via the Internet.
Numerous functions are available to support you.
For example, powerful search functions make it easy to find the
required products, which can be immediately checked for avail-
ability. Customer-specific discounts and preparation of quotes
can be carried out online as well as order tracking and tracing.
Please visit the A&D Mall on the Internet under:
http://www.siemens.com/automation/mall
Siemens KT10.1 · 2004 16/9
Appendix
Indexes
16
■
Order No. index
Type Page
5SY4
5SY4… 14/16
6EP1
6EP1 311-1SH02 13/2, 15/15
6EP1 311-1SH12 13/2, 15/15
6EP1 321-1SH02 13/4, 15/15
6EP1 322-1SH02 13/4, 15/15
6EP1 331-1SH02 13/8 , 15/15
6EP1 331-1SL11 2/3, 15/2
6EP1 331-2BA00 2/2, 15/2
6EP1 331-2BA10 2/2, 15/2
6EP1 332-1SH12 3/2, 15/3
6EP1 332-1SH22 3/2, 15/3
6EP1 332-1SH31 3/2, 15/3
6EP1 332-1SH42 13/8, 15/15
6EP1 332-1SH51 13/8, 15/15
6EP1 333-1AL12 4/3, 15/4
6EP1 333-1SL11 4/3, 15/3
6EP1 333-2AA00 4/2, 14/18, 15/4
6EP1 333-2BA00 4/2, 14/18, 15/4
6EP1 333-3BA00 4/2, 7/2, 14/19, 15/4
6EP1 334-1AL12 5/3, 15/4
6EP1 334-1SH01 5/3, 15/5
6EP1 334-1SL12 5/3, 15/5
6EP1 334-2AA00 5/2, 14/18, 15/5
6EP1 334-2BA00 5/2, 14/18, 15/5
6EP1 334-2CA00 5/3, 15/5
6EP1 334-3BA00 5/2, 7/2, 14/19, 15/5
6EP1 336-2BA00 6/3, 15/8
6EP1 336-3BA00 6/2, 15/7
6EP1 337-3BA00 6/2, 15/7
6EP1 351-1SH02 13/6, 15/15
6EP1 352-1SH02 13/6, 15/15
6EP1 353-0AA00 10/2, 15/13
6EP1 353-2BA00 10/2, 15/13
6EP1 354-1AL01 11/2, 15/14
6EP1 434-2BA00 7/6, 15/8
6EP1 436-2BA00 7/6, 14/20, 15/8
6EP1 436-3BA00 7/3, 14/21, 15/7
6EP1 437-2BA00 7/7, 14/20, 15/8
6EP1 437-2BA10 7/7, 15/8
6EP1 437-3BA00 7/3, 14/21, 15/7
6EP1 457-3BA00 10/2, 15/13
6EP1 536-2AA00 6/3, 15/8
6EP1 632-1AL01 11/2, 15/14
6EP1 731-2BA00 2/2, 15/2
6EP1 732-0AA00 2/3, 15/3
6EP1 931-2DC21 9/7, 15/11
6EP1 931-2DC31 9/7, 15/11
6EP1 931-2DC41 9/7, 15/11
6EP1 931-2EC21 9/9, 15/11
6EP1 931-2EC31 9/9, 15/11
6EP1 931-2EC41 9/9, 15/11
6EP1 931-2FC01 9/13, 15/11
6EP1 935-6MC01 9/14
6EP1 935-6MD11 9/16, 15/12
6EP1 935-6MD31 9/15, 15/12
6EP1 935-6ME21 9/17, 15/12
Type Page
6EP1
6EP1 935-6MF01 9/18, 15/12
6EP1 961-2BA00 8/4, 15/9
6EP1 961-3BA00 8/2, 15/9
6EP1 961-3BA10 8/2, 15/9
6EP1 961-3BA20 8/2, 15/9
6EP1 971-1AA01 8/6, 15/10
6EP1 971-2BA00 8/6, 15/10
6ES7
6ES7 305-1BA80-0AA0 2/3, 15/3
6ES7 307-1KA01-0AA 5/3, 15/5
6ES7 307-1BA00-0AA0 2/3, 15/2
6ES7 307-1EA00-0AA0 4/3, 15/3
6ES7 307-1EA80-0AA0 4/3, 15/3
8AW1
8AW1 011… 14/17
Siemens KT10.1 · 2004
16/10
Appendix
Indexes
16
■
Subject index
A
A&D online services 16/8
Alternative voltages 10/2
AS interface power supplies 11/2
B
Battery charging 14/15
Battery module 1.2 Ah 9/14
Battery module 12 Ah 9/18
Battery module 2.5 Ah 9/15
Battery module 3.2 Ah 9/16
Battery module 7 Ah 9/17
C
Conditions of sale and delivery 16/14
Contact persons 16/2
D
DC UPS module 15 A 9/3
DC UPS module 40 A 9/11
DC UPS module 6 A 9/3
DC UPS software 9/2
Dimension drawings section 15
F
Fusing of the output circuit, selectivity 14/15
L
Line-side connection 14/5
LOGO!Power 13/2
M
Mains specifications 14/5
Mounting 14/10
Mounting areas and fixing options 14/10
O
Overview of product families 1/6
P
Parallel connection for redundant operation
and performance enhancement 14/12
Planning aids 14/11
Possible system disturbances and causes 14/9
Power supplies, single-phase 2/2, 3/2
Power supplies, single- and two-phase 4/2, 5/2, 6/2
Power supplies, three-phase 7/2
S
Selection guide 1/9
Series connection to increase the voltage 14/14
SITOP modular buffer module 8/2
SITOP modular redundancy module 8/2
SITOP modular signalling module 8/2
SITOP select 8/4
Specification sheet for customized power supplies 12/3
Stabilized DC power supplies 14/2
T
Totally Integrated Automation –
innovations for more productivity 1/4
U
Uninterruptible power supplies 9/2
Siemens KT10.1 · 2004 16/11
Appendix
Customer Support
Our Services for Every Phase of Your Project
16
.I
In the face of harsh competition you need optimum conditions to
keep ahead all the time:
A strong starting position. A sophisticated strategy and team for
the necessary support - in every phase.
Service & Support from Siemens provides this support with a
complete range of different services for automation and drives.
In every phase: from planning and startup to maintenance and
upgrading.
Our specialists know when and where to act to keep the produc-
tivity and cost-effectiveness of your system running in top form.
■
Online Support
The comprehensive information
system available round the
clock via Internet ranging from
Product Support and Service &
Support services to Support
Tools in the Shop.
http://www.siemens.com/
automation/service&support
■
Technical Support
Competent consulting in techni-
cal questions covering a wide
range of customer-oriented ser-
vices for all our products and
systems.
Tel.: +49 (0)180 50 50 222
Fax: +49 (0)180 50 50 223
E-Mail:
adsupport@siemens.com
■
Technical Consulting
Support in the planning and de-
signing of your project from de-
tailed actual-state analysis,
target definition and consulting
on product and system ques-
tions right to the creation of the
automation solution. 1)
■
Configuration and Software Engineering
Support in configuring and de-
veloping with customer-oriented
services from actual configura-
tion to implementation of the au-
tomation project. 1)
■
Service On Site
With Service On Site we offer
services for startup and mainte-
nance, essential for ensuring
system availability.
In Germany
0180 50 50 444 1)
■
Repairs and Spare Parts
In the operating phase of a ma-
chine or automation system we
provide a comprehensive repair
and spare parts service ensur-
ing the highest degree of oper-
ating safety and reliability.
In Germany
0180 50 50 448 1)
■
Optimization and Upgrading
To enhance productivity and
save costs in your project we of-
fer high-quality services in opti-
mization and upgrading. 1)
1) For country-specific telephone numbers go to our Internet site at:
http://www.siemens.com/automation/service&support
Siemens KT10.1 · 2004
16/12
Appendix
Customer Support
16
■
Knowledge Base on CD-ROM
For locations without online con-
nections to the Internet there are
excerpts of the free part of the
information sources available on
CD-ROM (Service & Support
Knowledge Base). This CD-
ROM contains all the latest
product information at the time
of production (FAQs, Down-
loads, Tips and Tricks, Updates)
as well as general information
on Service and Technical Sup-
port.
The CD-ROM also includes a full-text search and our Knowledge
Manager for targeted searches for solutions. The CD-ROM will
be updated every 4 months.
Just the same as our online offer in the Internet, the Service &
Support Knowledge Base on CD comes complete in 5 lan-
guages (German, English, French, Italian, Spanish).
You can order the Service & Support Knowledge Base CD
from your Siemens contact.
Order no. 6ZB5310-0EP30-0BA2
Orders via the Internet
(with Automation Value Card or credit card) at:
http://www.siemens.com/automation/service&support
in the Shop domain.
■
Automation Value Card
Small card - great support
The Automation Value Card is an integral component of the com-
prehensive service concept with which Siemens Automation and
Drives will accompany you in each phase of your automation
project.
It doesn't matter whether you want just specific services from our
Technical Support or want to purchase high-quality Support
Tools in our Online Shop, you can always pay with your Automa-
tion Value Card. No invoicing, transparent and safe. With your
personal card number and associated PIN you can view the
state of your account and all transactions at any time.
Services on card. This is how it's done.
Card number and PIN are on the back of the Automation Value
Card. When delivered, the PIN is covered by a scratch field,
guaranteeing that the full credit is on the card.
By entering the card number and PIN you have full access to the
Service & Support services being offered. The charge for the
services procured is debited from the credits on your Automa-
tion Value Card.
All the services offered are marked in currency-neutral credits,
so you can use the Automation Value Card worldwide.
Detailed information on the services offered is available on our
Internet site at:
http://www.siemens.com/automation/service&support
Service & Support à la Card: Examples
Automation Value Card order numbers
Credits Order no.
200 6ES7 997-0BA00-0XA0
500 6ES7 997-0BB00-0XA0
1000 6ES7 997-0BC00-0XA0
10000 6ES7 997-0BG00-0XA0
Technical Support
”Priority“ Priority processing for urgent cases
”24 h“ Availability round the clock
„Extended“ Technical consulting for complex questions
Support Tools in the Support Shop
”System Utili-
ties“ Tools that can be used directly for configuration, anal-
ysis and testing
”Applications“ Complete topic solutions including ready-tested soft-
ware
”Functions &
Samples“ Adaptable blocks for accelerating your developments
Siemens KT10.1 · 2004 16/13
Appendix
Notes
16
Siemens KT10.1 · 2004
16/14
Appendix
Conditions of sale and delivery
16
■
Terms and Conditions of Sale and Delivery
By using this catalog you can acquire hardware and software
products described therein from the Siemens AG subject to the
following terms. Please note! The scope, the quality and the con-
ditions for supplies and services, including software products,
by any Siemens entity having a registered office outside of Ger-
many, shall be subject exclusively to the General Terms and
Conditions of the respective Siemens entity.
for customers with a seat or registered office in the
Federal Republic of Germany
The General Terms of Payment as well as the General Conditions
for the Supply of Products and Services of the Electrical and
Electronics Industry shall apply.
For software products, the General License Conditions for Soft-
ware Products for Automation and Drives for Customers with
Seat or registered Office in Germany shall apply.
for customers with a seat or registered office outside of
Germany
The General Terms of Payment as well as the General Conditions
for Supplies of Siemens, Automation and Drives for Customers
with a Seat or registered Office outside of Germany shall apply.
For software products, the General License Conditions for Soft-
ware Products for Automation and Drives for Customers with
Seat or registered Office outside of Germany shall apply.
General
The prices are in € (Euro) ex works, exclusive packaging.
The sales tax (value added tax) is not included in the prices.
It shall be debited separately at the respective rate according to
the applicable legal regulations.
In addition to the prices of products which include silver and/or
copper, surcharges may be calculated if the respective limits of
the notes are exceeded.
Prices are subject to change without prior notice. We will debit
the prices valid at the time of delivery.
The dimensions are in mm. Illustrations are not binding.
Insofar as there are no remarks on the corresponding pages,
- especially with regard to data, dimensions and weights given -
these are subject to change without prior notice.
Comprehensive Terms and Conditions of Sale and Delivery are
available free of charge from your local Siemens business office
under the following Order Nos.:
• 6ZB5310-0KR30-0BA0
(for customers based in the Federal Republic of Germany)
• 6ZB5310-0KS53-0BA0
(for customers based outside of theFederal Republic of
Germany)
or download them from the Internet:
www.siemens.com/automation/mall
(Germany: A&D Mall Online-Help System)
■
Export regulations
The products listed in this catalog / price list may be subject to
European / German and/or US export regulations.
Therefore, any export requiring a license is subject to approval
by the competent authorities.
According to current provisions, the following export regulations
must be observed with respect to the products featured in this
catalog / price list:
Even without a label or with an “AL: N“ or “ECCN: N“, authoriza-
tion may be required due to the final destination and purpose for
which the goods are to be used.
The deciding factors are the AL or ECCN export authorization
indicated on order confirmations, delivery notes and invoices.
Errors excepted and subject to change without prior notice.
A&D/VuL/En 14.11.03
AL Number of the German Export List.
Products marked other than “N“ require an export
license.
In the case of software products, the export des-
ignations of the relevant data medium must also
be generally adhered to.
Goods labeled with an “AL not equal to N“ are
subject to a European or German export authori-
zation when being exported out of the EU.
ECCN Export Control Classification Number.
Products marked other than “N“ are subject to a
reexport license to specific countries.
In the case of software products, the export
designations of the relevant data medium must
also be generally adhered to.
Goods labeled with an “ECCN not equal to N“ are
subject to a US re-export authorization.
Siemens AG
Automation and Drives
Sales Power Supplies, System Cables
Postfach 23 55
90713 FÜRTH
FEDERAL REPUBLIC OF GERMANY
Order No.
E86060-K2410-A101-A5-7600
KG 1004 27.0 BD 148 En/ 522194
Printed in the Federal Republic of Germany
Catalogs of the
Automation and Drives Group (A&D)
Further information can be obtained from our
branch offices listed in the appendix of this catalog
A&D/3U/En 28.09.04
Automation and Drives Catalog
Interactive catalog on CD-ROM
• The Offline Mall of Automation and Drives CA 01
Automation Systems for Machine Tools
SINUMERIK & SIMODRIVE NC 60
Drive Systems
Variable-Speed Drives
SINAMICS G130 Drive Converter Chassis Units
SINAMICS G150 Drive Converter Cabinet Units
D11
SINAMICS G110 Inverter Chassis Units D11.1
SINAMICS S120 Servo Control Drive System D21.2
SINAMICS S150 Drive Converter Cabinet Units D21.3
DC Motors DA 12
SIMOREG DC MASTER 6RA70 Digital Chassis
Converters
DA 21.1
SIMOREG K 6RA22 Analog Chassis Converters DA 21.2
SIMOREG DC MASTER 6RM70 Digital Converter
Cabinet Units
DA 22
SIMOVERT PM Modular Converter Systems DA 45
SIEMOSYN Motors DA 48
MICROMASTER 410/420/430/440 Inverters DA 51.2
MICROMASTER 411/COMBIMASTER 411 DA 51.3
SIMOVERT MV Medium-Voltage Drives DA 63
SIMOVERT MASTERDRIVES Vector Control DA 65.10
SIMOVERT MASTERDRIVES Motion Control DA 65.11
Synchronous and asynchronous servomotors for
SIMOVERT MASTERDRIVES
DA 65.3
SIMODRIVE 611 universal and POSMO DA 65.4
Low-Voltage Three-Phase-Motors
Squirrel-Cage Motors, Totally Enclosed, Fan-Cooled M 11
Automation Systems for Machine Tools SIMODRIVE NC 60
• Main Spindle Motors
• Feed Motors
• Converter Systems SIMODRIVE 611/POSMO
Drive and Control Components for Hoisting Equipment HE 1
Electrical Installation Technology
PDF: ALPHA Small Distribution Boards and
Distribution Boards
ET A1
PDF: ALPHA Side-by-Side Switchgear Cabinets ET A3
PDF: ALPHA FIX Terminal Blocks ET A5
PDF: BETA Modular Installation Devices ET B1
PDF: DELTA Switches and Outlets ET D1
PDF: GAMMA Building Management Systems ET G1
Factory Automation Sensors FS 10
Human Machine Interface Systems SIMATIC HMI ST 80
Industrial Communication for
Automation and Drives
IK PI
PDF: These catalogs are only available as pdf files.
Low-Voltage Controls and Distribution Catalog
Low-Voltage Switchgear – Controlgear for Industry LV 10
Power Distribution – Products and Systems
for Low-Voltage Power Distribution
LV 30
SIDAC-D reactors and SIDAC-F filters LV 63
SIVACON 8PS Busbar Trunking Systems
CD, BD01, BD2 up to 1250 A
LV 70
Busbar trunking systems LDA/LDC LV 71
Busbar trunking systems LXA/LXC LV 72
SENTRON WL NS WL
Motion Control System SIMOTION PM 10
Process Instrumentation and Analytics
Field Instruments for Process Automation
Measuring Instruments for Pressure,
Differential Pressure, Flow, Level and Temperature,
Positioners and Liquid Meters
FI 01
PDF: Indicators for panel mounting MP 12
SIREC Recorders and Accessories MP 20
SIPART, Controllers and Software MP 31
SIWAREX Weighing Systems WT 01
Continuous Weighing and Process Protection WT 02
Gas Analysis Equipment for the Process Industry PA 10
PDF: Process Analytics,
Components for the System Integration
PA 11
SIPAN Liquid Analysis PA 20
SIMATIC Industrial Automation Systems
SIMATIC PCS Process Control System ST 45
PDF: SIMATIC S5/505 Automation Systems ST 50
Components for Totally Integrated Automation and
Micro Automation
ST 70
SIMATIC PCS 7 Process Control System ST PCS 7
PDF: Add-ons for the SIMATIC PCS 7
Process Control System
ST PCS 7.A
SIMATIC Control Systems ST DA
SIPOS Electric Actuators
Electric Rotary, Linear and Part-turn Actuators MP 35
Electric Rotary Actuators for Nuclear Plants MP 35.1/.2
Systems Engineering
Power supplies SITOP power KT 10.1
System cabling SIMATIC TOP connect KT 10.2
System Solutions
Applications and Products for Industry are part of the
interactive catalog CA 01
TELEPERM M Process Control System
AS 235, AS 235H and AS 235K automation systems PLT 111
PDF: AS 488/TM automation systems PLT 112
Operating and monitoring with WinCC/TM PLT 123
CS 275 bus system PLT 130
sitop
Siemens AG
Automation and Drives
Systems Engineering
Sales Power Supplies, System Cables
www.siemens.com Order No.: E86060-K2410-A101-A5-7600
Power supplies
SITOP power
LOGO!Power
Catalog KT 10.1 2004SITOP Power supplies
Catalog KT 10.1 2004
The information provided in this catalog contains descriptions or
characteristics of performance which in case of actual use do not
always apply as described or which may change as a result of
further development of the products. An obligation to provide
the respective characteristics shall only exist if expressly agreed
in terms of contract. Availability and technical specifications
are subject to change without notice.
