PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Chip Monolithic Ceramic Capacitors Large Capacitance Type 1. Smaller size and higher capacitance value 2. High reliability and no polarity 3. Excellent pulse responsibility and noise reduction due to the low impedance at high frequency 4. Ta replacement 6 Applications General electronic equipment GRM033 GRM155 GRM185 GRM188 GRM216 GRM219 GRM21B GRM316 GRM319 GRM31M GRM31C GRM32C GRM32D GRM32E GRM43D GRM43E GRM43S GRM55F Dimensions (mm) L W T e min. g min. 0.6 0.03 0.3 0.03 0.3 0.03 0.1 to 0.2 0.2 1.0 0.05 0.5 0.05 0.5 0.05 0.15 to 0.35 0.3 1.6 0.1 0.8 0.1 0.5 +0/-0.2 0.2 to 0.5 0.5 1.6 0.1 0.8 0.1 0.8 0.1 0.2 to 0.5 0.5 0.6 0.1 2.0 0.1 1.25 0.1 0.85 0.1 0.2 to 0.7 0.7 1.25 0.1 0.6 0.1 3.2 0.15 1.6 0.15 0.85 0.1 0.3 to 0.8 1.5 1.15 0.1 3.2 0.2 1.6 0.2 1.6 0.2 1.6 0.2 3.2 0.3 2.5 0.2 2.0 0.2 0.3 1.0 2.5 0.2 2.0 0.2 4.5 0.4 3.2 0.3 2.5 0.2 0.3 2.0 2.8 0.2 5.7 0.4 5.0 0.4 3.2 0.2 0.3 2.0 e g e T Part Number Features L W High Dielectric Constant Type X5R (R6) Characteristics Part Number TC Code (Standard) Rated Voltage (Vdc) Capacitance Length L (mm) Width W (mm) Thickness T (mm) GRM188R61E474KA12 X5R (EIA) 25 0.47F 10% 1.60 0.80 0.80 GRM188R61E105KA12 X5R (EIA) 25 1.0F 10% 1.60 0.80 0.80 GRM21BR61E105KA99 X5R (EIA) 25 1.0F 10% 2.00 1.25 1.25 GRM219R61E225KA12 X5R (EIA) 25 2.2F 10% 2.00 1.25 0.85 GRM21BR61E225KA12 X5R (EIA) 25 2.2F 10% 2.00 1.25 1.25 GRM21BR61E335KA12 X5R (EIA) 25 3.3F 10% 2.00 1.25 1.25 GRM21BR61E475KA12 X5R (EIA) 25 4.7F 10% 2.00 1.25 1.25 GRM319R61E475KA12 X5R (EIA) 25 4.7F 10% 3.20 1.60 0.85 GRM31CR61E106KA12 X5R (EIA) 25 10F 10% 3.20 1.60 1.60 GRM32ER61E226KE15 X5R (EIA) 25 22F 10% 3.20 2.50 2.50 GRM188R61C474KA93 X5R (EIA) 16 0.47F 10% 1.60 0.80 0.80 GRM185R61C105KE44 X5R (EIA) 16 1.0F 10% 1.60 0.80 0.50 GRM188R61C105KA93 X5R (EIA) 16 1.0F 10% 1.60 0.80 0.80 GRM216R61C105KA88 X5R (EIA) 16 1.0F 10% 2.00 1.25 0.60 GRM188R61C225KE15 X5R (EIA) 16 2.2F 10% 1.60 0.80 0.80 GRM219R61C225KA88 X5R (EIA) 16 2.2F 10% 2.00 1.25 0.85 GRM21BR61C225KA88 X5R (EIA) 16 2.2F 10% 2.00 1.25 1.25 GRM316R61C225KA88 X5R (EIA) 16 2.2F 10% 3.20 1.60 0.60 GRM21BR61C335KA88 X5R (EIA) 16 3.3F 10% 2.00 1.25 1.25 GRM21BR61C475KA88 X5R (EIA) 16 4.7F 10% 2.00 1.25 1.25 GRM319R61C475KA88 X5R (EIA) 16 4.7F 10% 3.20 1.60 0.85 GRM32ER61C226KE20 X5R (EIA) 16 22F 10% 3.20 2.50 2.50 GRM43ER61C226KE01 X5R (EIA) 16 22F 10% 4.50 3.20 2.50 GRM32ER61C476KE15 X5R (EIA) 16 47F 10% 3.20 2.50 2.50 GRM155R61A154KE19 X5R (EIA) 10 0.15F 10% 1.00 0.50 0.50 GRM155R61A224KE19 X5R (EIA) 10 0.22F 10% 1.00 0.50 0.50 GRM185R61A105KE36 X5R (EIA) 10 1.0F 10% 1.60 0.80 0.50 GRM188R61A225KE34 X5R (EIA) 10 2.2F 10% 1.60 0.80 0.80 GRM188R61A225ME34 X5R (EIA) 10 2.2F 10% 1.60 0.80 0.80 GRM216R61A225KE24 X5R (EIA) 10 2.2F 10% 2.00 1.25 0.60 GRM219R61A225KA01 X5R (EIA) 10 2.2F 10% 2.00 1.25 0.85 GRM316R61A225KA01 X5R (EIA) 10 2.2F 10% 3.20 1.60 0.60 GRM219R61A335KE19 X5R (EIA) 10 3.3F 10% 2.00 1.25 0.85 GRM21BR61A335KA73 X5R (EIA) 10 3.3F 10% 2.00 1.25 1.25 GRM316R61A335KE19 X5R (EIA) 10 3.3F 10% 3.20 1.60 0.60 GRM219R61A475KE34 X5R (EIA) 10 4.7F 10% 2.00 1.25 0.85 Continued on the following page. 32 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Part Number TC Code (Standard) Rated Voltage (Vdc) Capacitance Length L (mm) Width W (mm) Thickness T (mm) GRM21BR61A475KA73 X5R (EIA) 10 4.7F 10% 2.00 1.25 1.25 GRM316R61A475KE19 X5R (EIA) 10 4.7F 10% 3.20 1.60 0.60 GRM319R61A475KA01 X5R (EIA) 10 4.7F 10% 3.20 1.60 0.85 GRM21BR61A106KE19 X5R (EIA) 10 10F 10% 2.00 1.25 1.25 GRM21BR61A106ME19 X5R (EIA) 10 10F 20% 2.00 1.25 1.25 GRM319R61A106KA19 X5R (EIA) 10 10F 10% 3.20 1.60 0.85 GRM31MR61A106KE19 X5R (EIA) 10 10F 10% 3.20 1.60 1.15 GRM32NR61A226KE19 X5R (EIA) 10 22F 10% 3.20 2.50 1.35 GRM32ER61A476KE20 X5R (EIA) 10 47F 10% 3.20 2.50 2.50 GRM43ER61A476KE19 X5R (EIA) 10 47F 10% 4.50 3.20 2.50 GRM033R60J153KE01 X5R (EIA) 6.3 15000pF 10% 0.60 0.30 0.30 GRM033R60J223KE01 X5R (EIA) 6.3 22000pF 10% 0.60 0.30 0.30 GRM033R60J333KE01 X5R (EIA) 6.3 33000pF 10% 0.60 0.30 0.30 GRM033R60J393KE19 X5R (EIA) 6.3 39000pF 10% 0.60 0.30 0.30 GRM033R60J473KE19 X5R (EIA) 6.3 47000pF 10% 0.60 0.30 0.30 GRM033R60J683KE19 X5R (EIA) 6.3 68000pF 10% 0.60 0.30 0.30 GRM033R60J104KE19 X5R (EIA) 6.3 0.10F 10% 0.60 0.30 0.30 GRM155R60J154KE01 X5R (EIA) 6.3 0.15F 10% 1.00 0.50 0.50 GRM155R60J224KE01 X5R (EIA) 6.3 0.22F 10% 1.00 0.50 0.50 GRM155R60J334KE01 X5R (EIA) 6.3 0.33F 10% 1.00 0.50 0.50 GRM155R60J474KE19 X5R (EIA) 6.3 0.47F 10% 1.00 0.50 0.50 GRM155R60J105KE19 X5R (EIA) 6.3 1.0F 10% 1.00 0.50 0.50 GRM185R60J105KE21 X5R (EIA) 6.3 1.0F 10% 1.60 0.80 0.50 GRM185R60J105KE26 X5R (EIA) 6.3 1.0F 10% 1.60 0.80 0.50 GRM185R60J225KE26 X5R (EIA) 6.3 2.2F 10% 1.60 0.80 0.50 GRM188R60J225KE01 X5R (EIA) 6.3 2.2F 10% 1.60 0.80 0.80 GRM188R60J225KE19 X5R (EIA) 6.3 2.2F 10% 1.60 0.80 0.80 GRM188R60J475KE19 X5R (EIA) 6.3 4.7F 10% 1.60 0.80 0.80 GRM219R60J475KE01 X5R (EIA) 6.3 4.7F 10% 2.00 1.25 0.85 GRM219R60J475KE19 X5R (EIA) 6.3 4.7F 10% 2.00 1.25 0.85 GRM219R60J475KE32 X5R (EIA) 6.3 4.7F 10% 2.00 1.25 0.85 GRM219R60J106KE19 X5R (EIA) 6.3 10F 10% 2.00 1.25 0.85 GRM219R60J106ME19 X5R (EIA) 6.3 10F 20% 2.00 1.25 0.85 GRM21BR60J106KE01 X5R (EIA) 6.3 10F 10% 2.00 1.25 1.25 GRM21BR60J106KE19 X5R (EIA) 6.3 10F 10% 2.00 1.25 1.25 GRM21BR60J106ME01 X5R (EIA) 6.3 10F 20% 2.00 1.25 1.25 GRM21BR60J106ME19 X5R (EIA) 6.3 10F 20% 2.00 1.25 1.25 GRM319R60J106KE01 X5R (EIA) 6.3 10F 10% 3.20 1.60 0.85 GRM319R60J106KE19 X5R (EIA) 6.3 10F 10% 3.20 1.60 0.85 GRM31MR60J106KE19 X5R (EIA) 6.3 10F 10% 3.20 1.60 1.15 GRM31CR60J156KE19 X5R (EIA) 6.3 15F 10% 3.20 1.60 1.60 GRM21BR60J226ME39 X5R (EIA) 6.3 22F 20% 2.00 1.25 1.25 GRM31CR60J226KE19 X5R (EIA) 6.3 22F 10% 3.20 1.60 1.60 GRM31CR60J226ME19 X5R (EIA) 6.3 22F 20% 3.20 1.60 1.60 GRM32DR60J226KA01 X5R (EIA) 6.3 22F 10% 3.20 2.50 2.00 GRM32DR60J336ME19 X5R (EIA) 6.3 33F 10% 3.20 2.50 2.00 GRM43DR60J336KE01 X5R (EIA) 6.3 33F 10% 4.50 3.20 2.00 GRM31CR60J476ME19 X5R (EIA) 6.3 47F 20% 3.20 1.60 1.60 GRM32ER60J476ME20 X5R (EIA) 6.3 47F 20% 3.20 2.50 2.50 GRM43ER60J476KE01 X5R (EIA) 6.3 47F 10% 4.50 3.20 2.50 GRM32ER60J107ME20 X5R (EIA) 6.3 100F 20% 3.20 2.50 2.50 GRM43SR60J107ME20 X5R (EIA) 6.3 100F 20% 4.50 3.20 2.80 GRM188R60G106ME47 X5R (EIA) 4 10F 20% 1.60 0.80 0.80 6 33 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. High Dielectric Constant Type X6S/X7R/X7S (C8/R7/C7) Characteristics 6 Part Number TC Code (Standard) Rated Voltage (Vdc) Capacitance (F) Length L (mm) Width W (mm) Thickness T (mm) GRM188C80G475KE19 X6S(EIA) 4 4.7 10% 1.60 0.80 0.80 GRM21BR71E225KA73 X7R (EIA) 25 2.2 10% 2.00 1.25 1.25 GRM55ER71E156KA01 X7R (EIA) 25 15 10% 5.70 5.00 2.50 GRM31CR71C106KAC7 X7R (EIA) 16 10 10% 3.20 1.60 1.60 GRM32ER71A226KE20 X7R (EIA) 10 22 10% 3.20 2.50 2.50 GRM32ER71A226ME20 X7R (EIA) 10 22 20% 3.20 2.50 2.50 GRM43ER71A226KE01 X7R (EIA) 10 22 10% 4.50 3.20 2.50 GRM21BC71A335KA73 X7S(EIA) 10 3.3 10% 2.00 1.25 1.25 GRM21BC71A475KA73 X7S(EIA) 10 4.7 10% 2.00 1.25 1.25 High Dielectric Constant Type Y5V (F5) Characteristics Part Number TC Code (Standard) Rated Voltage (Vdc) Capacitance (F) Length L (mm) Width W (mm) Thickness T (mm) GRM188F51A225ZE01 Y5V (EIA) 10 2.2 +80/-20% 1.60 0.80 0.80 GRM188F51A475ZE20 Y5V (EIA) 10 4.7 +80/-20% 1.60 0.80 0.80 GRM31CF51A226ZE01 Y5V (EIA) 10 22 +80/-20% 3.20 1.60 1.60 GRM32CF51A226ZA01 Y5V (EIA) 10 22 +80/-20% 3.20 2.50 1.60 GRM155F50J105ZE01 Y5V (EIA) 6.3 1.0 +80/-20% 1.00 0.50 0.50 GRM188F50J225ZE01 Y5V (EIA) 6.3 2.2 +80/-20% 1.60 0.80 0.80 GRM188F50J475ZE20 Y5V (EIA) 6.3 4.7 +80/-20% 1.60 0.80 0.80 GRM21BF50J106ZE01 Y5V (EIA) 6.3 10 +80/-20% 2.00 1.25 1.25 GRM31CF50J226ZE01 Y5V (EIA) 6.3 22 +80/-20% 3.20 1.60 1.60 GRM32EF50J107ZE20 Y5V (EIA) 6.3 100 +80/-20% 3.20 2.50 2.50 34 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Specifications and Test Methods No. 1 Specifications Item Operating Temperature Range Test Method B1, B3, F1 : Y25 to W85D R6 : Y55 to W85D F5 : Y30 to W85D C8 : Y55 to W105D, C7 : -55 to W125D Reference temperature : 25D (B1, B3, F1 : 20D) 2 Rated Voltage See the previous pages. The rated voltage is defined as the maximum voltage which may be applied continuously to the capacitor. When AC voltage is superimposed on DC voltage, VP-P or VO-P, whichever is larger, should be maintained within the rated voltage range. 3 Appearance No defects or abnormalities Visual inspection 4 Dimensions Within the specified dimensions Using calipers No defects or abnormalities No failure should be observed when 250% of the rated voltage is applied between the terminations for 1 to 5 seconds, provided the charge/discharge current is less than 50mA. More than 50 * F The insulation resistance should be measured with a DC voltage not exceeding the rated voltage at reference temperature and 75%RH max. and within 1 minutes of charging, provided the charge/discharge current is less than 50mA. 5 Dielectric Strength 6 Insulation Resistance Within the specified tolerance 7 *Table 1 GRM155 B3/R6 1A 124 to 224 GRM185 B3/R6 1A 105 GRM188 B3/R6 1C/1A 225 GRM219 B3/R6 1A 475 GRM21B B3/R6 1C/1A 106 Capacitance B1, B3, R6, C7, C8 : 0.1 max. F1, F5 : 0.2 max. 8 *Table 1 GRM155 B3/R6 1A 124 to 224 GRM185 B3/R6 1A 105 GRM188 B3/R6 1C/1A 225 GRM219 B3/R6 1A 475 GRM21B B3/R6 1C/1A 106 Dissipation Factor (D.F.) No bias B1, B3 : Within T10% (Y25 to W85D) F1 : Within W30/Y80% (Y25 to W85D) R6 : Within T15% (Y55 to W85D) F5 : Within W22/Y82% (Y30 to W85D) C7 : Within T22% (Y55 to W125D) C8 : Within T22% (Y55 to W105D) The capacitance should be measured at reference temperature at the frequency and voltage shown in the table. Capacitance CV10F (10V min.)*1 CV10F (6.3V max.) CG10F Frequency 1T0.1kHz 1T0.1kHz 120T24Hz Voltage 1.0T0.2Vrms 0.5T0.1Vrms 0.5T0.1Vrms *1 However the voltage is 0.5T0.1Vrms about Table 1 items on the left side. The D.F. should be measured at reference temperature at the frequency and voltage shown in the table. Capacitance CV10F (10V min.)*1 CV10F (6.3V max.) CG10F Frequency 1T0.1kHz 1T0.1kHz 120T24Hz Voltage 1.0T0.2Vrms 0.5T0.1Vrms 0.5T0.1Vrms *1 However the voltage is 0.5T0.1Vrms about Table 1 items on the left side. The capacitance change should be measured after 5 min. at each specified temp. stage. The ranges of capacitance change compared with the reference temperature value over the temperature ranges shown in the table should be within the specified ranges.* In case of applying voltage, the capacitance change should be measured after 1 more min. with applying voltage in equilibration of each temp. stage. *GRM43 B1/R6 0J/1A 336/476 only : 1.0T0.2Vrms 9 Capacitance Temperature Characteristics 50% of the Rated Voltage B1: Within W10/Y30% F1: Within W30/Y95% Step 1 Temperature (C) Reference tempereture T2 2 -55T3 (for R6, C7, C8)/ -25T3 (for B1, B3, F1) -30T3 (for F5) 3 Reference tempereture T2 4 85T3 (for B1, B3, F1, R6, F5) 125T3 (for C7)/ 105T3 (for C8) 5 20T2 6 -25T3 (for B1, F1) 7 20T2 8 85T3 (for B1, F1) Applying Voltage (V) No bias 50% of the rated voltage #Initial measurement for high dielectric constant type Perform a heat treatment at 150 W0/Y10C for one hour and then set for 24T2 hours at room temperature. Perform the initial measurement. Continued on the following page. 35 6 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Specifications and Test Methods Continued from the preceding page. Specifications Item Test Method No removal of the terminations or other defects should occur. Adhesive Strength of Termination a 10 b c Solder resist Baked electrode or copper foil 6 Fig. 1a Appearance No defects or abnormalities Capacitance Within the specified tolerance D.F. B1, B3, R6, C7, C8 : 0.1 max. F1, F5 : 0.2 max. Type GRp03 GRp15 GRM18 GRM21 GRM31 GRM32 GRM43 GRM55 a 0.3 0.4 1.0 1.2 2.2 2.2 3.5 4.5 b 0.9 1.5 3.0 4.0 5.0 5.0 7.0 8.0 c 0.3 0.5 1.2 1.65 2.0 2.9 3.7 5.6 Solder the capacitor on the test jig (glass epoxy board) in the same manner and under the same conditions as (10). The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55Hz. The frequency range, from 10 to 55Hz and return to 10Hz, should be traversed in approximately 1 minute. This motion should be applied for a period of 2 hours in each 3 mutually perpendicular directions (total of 6 hours). 11 Vibration No cracking or marking defects should occur. 50 Pressurizing speed : 1.0mm/sec. Pressurize R230 Solder the capacitor on the test jig (glass epoxy board) shown in Fig. 2a using an eutectic solder. Then apply a force in the direction shown in Fig. 3a for 5T1 sec. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. b VWZ[(c)XT_\|U(R)]YZSTWQ,RV^[ Y]^(R)Z 20 Solder the capacitor on the test jig (glass epoxy board) shown in Fig. 1a using an eutectic solder. Then apply 10N* force in parallel with the test jig for 10T1sec. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. *5N : GRp15/GRM18, 2N : GRp33 o4.5 40 No. c Flexure : V1 a 100 12 Deflection Capacitance meter 45 45 t : 1.6mm Fig. 2a (GRp03, GRp15 : t : 0.8mm) Fig.3a 13 Solderability of Termination 75% of the terminations is to be soldered evenly and continuously. Type GRp03 GRp15 GRM18 GRM21 GRM31 GRM32 GRM43 GRM55 a 0.3 0.4 1.0 1.2 2.2 2.2 3.5 4.5 b 0.9 1.5 3.0 4.0 5.0 5.0 7.0 8.0 c 0.3 0.5 1.2 1.65 2.0 2.9 3.7 5.6 (in mm) Immerse the capacitor in a solution of ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight proportion) . Preheat at 80 to 120D for 10 to 30 seconds. After preheating, immerse in an eutectic solder solution for 2T0.5 seconds at 230T5D or Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5C. Continued on the following page. 36 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Specifications and Test Methods Continued from the preceding page. No. Specifications Item Appearance No defects or abnormalities Capacitance Change B1, B3, R6, C7, C8 : Within T7.5% F1, F5 : Within T20% Q/D.F. Resistance I.R. to 14 Soldering Heat Dielectric Strength Temperature 15 Sudden Change B1, B3, R6, C7, C8 : 0.1 max. F1, F5 : 0.2 max. More than 50 * F Test Method Preheat the capacitor at 120 to 150D for 1 minute. Immerse the capacitor in an eutectic solder or Sn-3.0Ag-0.5Cu solder solution at 270T5D for 10T0.5 seconds. Set at room temperature for 24T2 hours, then measure. #Initial measurement for high dielectric constant type Perform a heat treatment at 150W0/Y10D for one hour and then set at room temperature for 24T2 hours. Perform the initial measurement. *Preheating for GRM32/43/55 No defects Appearance No defects or abnormalities Capacitance Change B1, B3, R6, C7, C8 : Within T7.5% F1, F5 : Within T20% D.F. B1, B3, R6, C7, C8 : 0.1 max. F1, F5 : 0.2 max. I.R. More than 50 * F Step 1 Temperature 100 to 120D Time 1 min. 2 170 to 200D 1 min. Fix the capacitor to the supporting jig in the same manner and under the same conditions as (10). Perform the five cycles according to the four heat treatments shown in the following table. Set for 24T2 hours at room temperature, then measure. Step 1 2 3 4 Min. Max. Room Room Operating Operating Temp. (D) Temp. Temp. Temp. W0/Y3 Temp. W3/Y0 Time (min.) 16 17 High Temperature High Humidity (Steady) Dielectric Strength No defects Appearance No defects or abnormalities Capacitance Change B1, B3, R6, C7, C8 : Within T12.5% F1, F5 : Within T30% D.F. B1, B3, R6, C7, C8 : 0.2 max. F1, F5 : 0.4 max. I.R. More than 12.5 * F Appearance No defects or abnormalities Capacitance Change B1, B3, R6, C7, C8 : Within T12.5% F1, F5 : Within T30% D.F. B1, B3, R6, C7, C8 : 0.1 max. F1, F5 : 0.4 max. I.R. More than 25 * F Durability 6 30T3 2 to 3 30T3 2 to 3 #Initial measurement for high dielectric constant type Perform a heat treatment at 150W0/Y10D for one hour and then set at room temperature for 24T2 hours. Perform the initial measurement. Apply the rated voltage at 40T2D and 90 to 95% humidity for 500T12 hours. The charge/discharge current is less than 50mA. #Initial measurement Perform a heat treatment at 150W0/Y10D for one hour and then let sit for 24T2 hours at room temperature. Perform the initial measurement. #Measurement after test Perform a heat treatment at 150W0/Y10D for one hour and then let sit for 24T2 hours at room temperature, then measure. Apply 150% of the rated voltage for 1000T12 hours at the maximum operating temperature T3D. Let sit for 24T2 hours at room temperature, then measure. The charge/discharge current is less than 50mA. #Initial measurement Perform a heat treatment at 150W0/Y10D for one hour and then let sit for 24T2 hours at room temperature. Perform the initial measurement. #Measurement after test Perform a heat treatment at 150W0/Y10D for one hour and then let sit for 24T2 hours at room temperature, then measure. 37