32
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Chip Monolithic Ceramic Capacitors
Large Capacitance Type
■ Features
1. Smaller size and higher capacitance value
2. High reliability and no polarity
3. Excellent pulse responsibility and noise reduction
due to the low impedance at high frequency
4. Ta replacement
■ Applications
General electronic equipment
L
T
L W T
Dimensions (mm) e min.
g min.
0.3
0.3
2.0 ±0.2
GRM32D 2.5 ±0.2
GRM32E
4.5 ±0.4 3.2 ±0.3 2.0
2.8 ±0.2
GRM43S 2.5 ±0.2
GRM43E 2.0 ±0.2
GRM43D
5.7 ±0.4 5.0 ±0.4 2.03.2 ±0.2
GRM55F
0.85 ±0.1
1.25 ±0.1
GRM21B 2.0 ±0.1 1.25 ±0.1 0.2 to 0.7 0.7
0.6 ±0.1
GRM219
1.6 ±0.1 0.8 ±0.1 0.2 to 0.5 0.50.8 ±0.1
GRM188
GRM216
1.6 ±0.1 0.8 ±0.1 0.2 to 0.5 0.5
0.5 +0/-0.2
GRM185
W
e eg
1.6 ±0.2
GRM31M 0.85 ±0.1
GRM319 1.15 ±0.1
GRM31C
3.2 ±0.3 2.5 ±0.2 0.3 1.0
3.2 ±0.2 1.6 ±0.2
3.2 ±0.15 1.6 ±0.15 0.3 to 0.8 1.5
1.6 ±0.2
GRM32C
0.6 ±0.1
GRM316
1.0 ±0.05 0.5 ±0.05
0.15 to 0.35
0.30.5 ±0.05
0.6 ±0.03 0.3 ±0.03 0.1 to 0.2 0.20.3 ±0.03
GRM155
GRM033
Part Number
High Dielectric Constant Type X5R (R6) Characteristics
Part Number TC Code
(Standard) Rated Voltage
(Vdc) Capacitance Length L
(mm) Width W
(mm) Thickness T
(mm)
GRM188R61E474KA12 X5R (EIA) 25 0.47µF ±10% 1.60 0.80 0.80
GRM188R61E105KA12 X5R (EIA) 25 1.0µF ±10% 1.60 0.80 0.80
GRM21BR61E105KA99 X5R (EIA) 25 1.0µF ±10% 2.00 1.25 1.25
GRM219R61E225KA12 X5R (EIA) 25 2.2µF ±10% 2.00 1.25 0.85
GRM21BR61E225KA12 X5R (EIA) 25 2.2µF ±10% 2.00 1.25 1.25
GRM21BR61E335KA12 X5R (EIA) 25 3.3µF ±10% 2.00 1.25 1.25
GRM21BR61E475KA12 X5R (EIA) 25 4.7µF ±10% 2.00 1.25 1.25
GRM319R61E475KA12 X5R (EIA) 25 4.7µF ±10% 3.20 1.60 0.85
GRM31CR61E106KA12 X5R (EIA) 25 10µF ±10% 3.20 1.60 1.60
GRM32ER61E226KE15 X5R (EIA) 25 22µF ±10% 3.20 2.50 2.50
GRM188R61C474KA93 X5R (EIA) 16 0.47µF ±10% 1.60 0.80 0.80
GRM185R61C105KE44 X5R (EIA) 16 1.0µF ±10% 1.60 0.80 0.50
GRM188R61C105KA93 X5R (EIA) 16 1.0µF ±10% 1.60 0.80 0.80
GRM216R61C105KA88 X5R (EIA) 16 1.0µF ±10% 2.00 1.25 0.60
GRM188R61C225KE15 X5R (EIA) 16 2.2µF ±10% 1.60 0.80 0.80
GRM219R61C225KA88 X5R (EIA) 16 2.2µF ±10% 2.00 1.25 0.85
GRM21BR61C225KA88 X5R (EIA) 16 2.2µF ±10% 2.00 1.25 1.25
GRM316R61C225KA88 X5R (EIA) 16 2.2µF ±10% 3.20 1.60 0.60
GRM21BR61C335KA88 X5R (EIA) 16 3.3µF ±10% 2.00 1.25 1.25
GRM21BR61C475KA88 X5R (EIA) 16 4.7µF ±10% 2.00 1.25 1.25
GRM319R61C475KA88 X5R (EIA) 16 4.7µF ±10% 3.20 1.60 0.85
GRM32ER61C226KE20 X5R (EIA) 16 22µF ±10% 3.20 2.50 2.50
GRM43ER61C226KE01 X5R (EIA) 16 22µF ±10% 4.50 3.20 2.50
GRM32ER61C476KE15 X5R (EIA) 16 47µF ±10% 3.20 2.50 2.50
GRM155R61A154KE19 X5R (EIA) 10 0.15µF ±10% 1.00 0.50 0.50
GRM155R61A224KE19 X5R (EIA) 10 0.22µF ±10% 1.00 0.50 0.50
GRM185R61A105KE36 X5R (EIA) 10 1.0µF ±10% 1.60 0.80 0.50
GRM188R61A225KE34 X5R (EIA) 10 2.2µF ±10% 1.60 0.80 0.80
GRM188R61A225ME34 X5R (EIA) 10 2.2µF ±10% 1.60 0.80 0.80
GRM216R61A225KE24 X5R (EIA) 10 2.2µF ±10% 2.00 1.25 0.60
GRM219R61A225KA01 X5R (EIA) 10 2.2µF ±10% 2.00 1.25 0.85
GRM316R61A225KA01 X5R (EIA) 10 2.2µF ±10% 3.20 1.60 0.60
GRM219R61A335KE19 X5R (EIA) 10 3.3µF ±10% 2.00 1.25 0.85
GRM21BR61A335KA73 X5R (EIA) 10 3.3µF ±10% 2.00 1.25 1.25
GRM316R61A335KE19 X5R (EIA) 10 3.3µF ±10% 3.20 1.60 0.60
GRM219R61A475KE34 X5R (EIA) 10 4.7µF ±10% 2.00 1.25 0.85
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
05.12.14
33
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part Number TC Code
(Standard) Rated Voltage
(Vdc) Capacitance Length L
(mm) Width W
(mm) Thickness T
(mm)
Continued from the preceding page.
GRM21BR61A475KA73 X5R (EIA) 10 4.7µF ±10% 2.00 1.25 1.25
GRM316R61A475KE19 X5R (EIA) 10 4.7µF ±10% 3.20 1.60 0.60
GRM319R61A475KA01 X5R (EIA) 10 4.7µF ±10% 3.20 1.60 0.85
GRM21BR61A106KE19 X5R (EIA) 10 10µF ±10% 2.00 1.25 1.25
GRM21BR61A106ME19 X5R (EIA) 10 10µF ±20% 2.00 1.25 1.25
GRM319R61A106KA19 X5R (EIA) 10 10µF ±10% 3.20 1.60 0.85
GRM31MR61A106KE19 X5R (EIA) 10 10µF ±10% 3.20 1.60 1.15
GRM32NR61A226KE19 X5R (EIA) 10 22µF ±10% 3.20 2.50 1.35
GRM32ER61A476KE20 X5R (EIA) 10 47µF ±10% 3.20 2.50 2.50
GRM43ER61A476KE19 X5R (EIA) 10 47µF ±10% 4.50 3.20 2.50
GRM033R60J153KE01 X5R (EIA) 6.3 15000pF ±10% 0.60 0.30 0.30
GRM033R60J223KE01 X5R (EIA) 6.3 22000pF ±10% 0.60 0.30 0.30
GRM033R60J333KE01 X5R (EIA) 6.3 33000pF ±10% 0.60 0.30 0.30
GRM033R60J393KE19 X5R (EIA) 6.3 39000pF ±10% 0.60 0.30 0.30
GRM033R60J473KE19 X5R (EIA) 6.3 47000pF ±10% 0.60 0.30 0.30
GRM033R60J683KE19 X5R (EIA) 6.3 68000pF ±10% 0.60 0.30 0.30
GRM033R60J104KE19 X5R (EIA) 6.3 0.10µF ±10% 0.60 0.30 0.30
GRM155R60J154KE01 X5R (EIA) 6.3 0.15µF ±10% 1.00 0.50 0.50
GRM155R60J224KE01 X5R (EIA) 6.3 0.22µF ±10% 1.00 0.50 0.50
GRM155R60J334KE01 X5R (EIA) 6.3 0.33µF ±10% 1.00 0.50 0.50
GRM155R60J474KE19 X5R (EIA) 6.3 0.47µF ±10% 1.00 0.50 0.50
GRM155R60J105KE19 X5R (EIA) 6.3 1.0µF ±10% 1.00 0.50 0.50
GRM185R60J105KE21 X5R (EIA) 6.3 1.0µF ±10% 1.60 0.80 0.50
GRM185R60J105KE26 X5R (EIA) 6.3 1.0µF ±10% 1.60 0.80 0.50
GRM185R60J225KE26 X5R (EIA) 6.3 2.2µF ±10% 1.60 0.80 0.50
GRM188R60J225KE01 X5R (EIA) 6.3 2.2µF ±10% 1.60 0.80 0.80
GRM188R60J225KE19 X5R (EIA) 6.3 2.2µF ±10% 1.60 0.80 0.80
GRM188R60J475KE19 X5R (EIA) 6.3 4.7µF ±10% 1.60 0.80 0.80
GRM219R60J475KE01 X5R (EIA) 6.3 4.7µF ±10% 2.00 1.25 0.85
GRM219R60J475KE19 X5R (EIA) 6.3 4.7µF ±10% 2.00 1.25 0.85
GRM219R60J475KE32 X5R (EIA) 6.3 4.7µF ±10% 2.00 1.25 0.85
GRM219R60J106KE19 X5R (EIA) 6.3 10µF ±10% 2.00 1.25 0.85
GRM219R60J106ME19 X5R (EIA) 6.3 10µF ±20% 2.00 1.25 0.85
GRM21BR60J106KE01 X5R (EIA) 6.3 10µF ±10% 2.00 1.25 1.25
GRM21BR60J106KE19 X5R (EIA) 6.3 10µF ±10% 2.00 1.25 1.25
GRM21BR60J106ME01 X5R (EIA) 6.3 10µF ±20% 2.00 1.25 1.25
GRM21BR60J106ME19 X5R (EIA) 6.3 10µF ±20% 2.00 1.25 1.25
GRM319R60J106KE01 X5R (EIA) 6.3 10µF ±10% 3.20 1.60 0.85
GRM319R60J106KE19 X5R (EIA) 6.3 10µF ±10% 3.20 1.60 0.85
GRM31MR60J106KE19 X5R (EIA) 6.3 10µF ±10% 3.20 1.60 1.15
GRM31CR60J156KE19 X5R (EIA) 6.3 15µF ±10% 3.20 1.60 1.60
GRM21BR60J226ME39 X5R (EIA) 6.3 22µF ±20% 2.00 1.25 1.25
GRM31CR60J226KE19 X5R (EIA) 6.3 22µF ±10% 3.20 1.60 1.60
GRM31CR60J226ME19 X5R (EIA) 6.3 22µF ±20% 3.20 1.60 1.60
GRM32DR60J226KA01 X5R (EIA) 6.3 22µF ±10% 3.20 2.50 2.00
GRM32DR60J336ME19 X5R (EIA) 6.3 33µF ±10% 3.20 2.50 2.00
GRM43DR60J336KE01 X5R (EIA) 6.3 33µF ±10% 4.50 3.20 2.00
GRM31CR60J476ME19 X5R (EIA) 6.3 47µF ±20% 3.20 1.60 1.60
GRM32ER60J476ME20 X5R (EIA) 6.3 47µF ±20% 3.20 2.50 2.50
GRM43ER60J476KE01 X5R (EIA) 6.3 47µF ±10% 4.50 3.20 2.50
GRM32ER60J107ME20 X5R (EIA) 6.3 100µF ±20% 3.20 2.50 2.50
GRM43SR60J107ME20 X5R (EIA) 6.3 100µF ±20% 4.50 3.20 2.80
GRM188R60G106ME47 X5R (EIA) 4 10µF ±20% 1.60 0.80 0.80
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
05.12.14
34
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
High Dielectric Constant Type X6S/X7R/X7S (C8/R7/C7) Characteristics
Part Number TC Code
(Standard) Rated Voltage
(Vdc) Capacitance
(µF) Length L
(mm) Width W
(mm) Thickness T
(mm)
GRM188C80G475KE19 X6S(EIA) 4 4.7 ±10% 1.60 0.80 0.80
GRM21BR71E225KA73 X7R (EIA) 25 2.2 ±10% 2.00 1.25 1.25
GRM55ER71E156KA01 X7R (EIA) 25 15 ±10% 5.70 5.00 2.50
GRM31CR71C106KAC7 X7R (EIA) 16 10 ±10% 3.20 1.60 1.60
GRM32ER71A226KE20 X7R (EIA) 10 22 ±10% 3.20 2.50 2.50
GRM32ER71A226ME20 X7R (EIA) 10 22 ±20% 3.20 2.50 2.50
GRM43ER71A226KE01 X7R (EIA) 10 22 ±10% 4.50 3.20 2.50
GRM21BC71A335KA73 X7S(EIA) 10 3.3 ±10% 2.00 1.25 1.25
GRM21BC71A475KA73 X7S(EIA) 10 4.7 ±10% 2.00 1.25 1.25
High Dielectric Constant Type Y5V (F5) Characteristics
Part Number TC Code
(Standard) Rated Voltage
(Vdc) Capacitance
(µF) Length L
(mm) Width W
(mm) Thickness T
(mm)
GRM188F51A225ZE01 Y5V (EIA) 10 2.2 +80/-20% 1.60 0.80 0.80
GRM188F51A475ZE20 Y5V (EIA) 10 4.7 +80/-20% 1.60 0.80 0.80
GRM31CF51A226ZE01 Y5V (EIA) 10 22 +80/-20% 3.20 1.60 1.60
GRM32CF51A226ZA01 Y5V (EIA) 10 22 +80/-20% 3.20 2.50 1.60
GRM155F50J105ZE01 Y5V (EIA) 6.3 1.0 +80/-20% 1.00 0.50 0.50
GRM188F50J225ZE01 Y5V (EIA) 6.3 2.2 +80/-20% 1.60 0.80 0.80
GRM188F50J475ZE20 Y5V (EIA) 6.3 4.7 +80/-20% 1.60 0.80 0.80
GRM21BF50J106ZE01 Y5V (EIA) 6.3 10 +80/-20% 2.00 1.25 1.25
GRM31CF50J226ZE01 Y5V (EIA) 6.3 22 +80/-20% 3.20 1.60 1.60
GRM32EF50J107ZE20 Y5V (EIA) 6.3 100 +80/-20% 3.20 2.50 2.50
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
05.12.14
No. Item Specifications Test Method
See the previous pages.
Within the specified dimensions
No defects or abnormalities
More than 50Ω· F
B1, B3, R6, C7, C8 : 0.1 max.
F1, F5 : 0.2 max.
B1, B3 : Within T10% (Y25 to W85D)
F1 : Within W30/Y80% (Y25 to W85D)
R6 : Within T15% (Y55 to W85D)
F5 : Within W22/Y82% (Y30 to W85D)
C7 : Within T22% (Y55 to W125D)
C8 : Within T22% (Y55 to W105D)
B1: Within W10/Y30%
F1: Within W30/Y95%
Within the specified tolerance
No defects or abnormalities
B1, B3, F1 : Y25 to W85D
R6 : Y55 to W85D
F5 : Y30 to W85D
C8 : Y55 to W105D, C7 : -55 to W125D
Operating
Temperature
Range
Rated Voltage
Appearance
Dimensions
Dielectric Strength
Insulation
Resistance
Capacitance
Dissipation Factor
(D.F.)
Capacitance
Temperature
Characteristics
No bias
50% of
the Rated
Voltage
1
2
3
4
5
6
7
8
9
Using calipers
The insulation resistance should be measured with a DC voltage
not exceeding the rated voltage at reference temperature and
75%RH max. and within 1 minutes of charging, provided the
charge/discharge current is less than 50mA.
The capacitance should be measured at reference temperature
at the frequency and voltage shown in the table.
The D.F. should be measured at reference temperature at the
frequency and voltage shown in the table.
The capacitance change should be measured after 5 min. at
each specified temp. stage.
The ranges of capacitance change compared with the
reference temperature value over the temperature ranges
shown in the table should be within the specified ranges.*
In case of applying voltage, the capacitance change should be
measured after 1 more min. with applying voltage in
equilibration of each temp. stage.
*GRM43 B1/R6 0J/1A 336/476 only : 1.0T0.2Vrms
No failure should be observed when 250% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
Visual inspection
The rated voltage is defined as the maximum voltage which
may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, VP-P or VO-P,
whichever is larger, should be maintained within the rated
voltage range.
Reference temperature : 25D
(B1, B3, F1 : 20D)
Continued on the following page.
Capacitance
CV10µF (10V min.)*1
CV10µF (6.3V max.)
CG10µF
1T0.1kHz
1T0.1kHz
120T24Hz
1.0T0.2Vrms
0.5T0.1Vrms
0.5T0.1Vrms
Frequency Voltage
*1 However the voltage is 0.5T0.1Vrms about Table 1
items on the left side.
Capacitance
CV10µF (10V min.)*1
CV10µF (6.3V max.)
CG10µF
1T0.1kHz
1T0.1kHz
120T24Hz
1.0T0.2Vrms
0.5T0.1Vrms
0.5T0.1Vrms
Frequency Voltage
*1 However the voltage is 0.5T0.1Vrms about Table 1
items on the left side.
GRM155 B3/R6 1A 124 to 224
GRM185 B3/R6 1A 105
GRM188 B3/R6 1C/1A 225
GRM219 B3/R6 1A 475
GRM21B B3/R6 1C/1A 106
*Table 1
GRM155 B3/R6 1A 124 to 224
GRM185 B3/R6 1A 105
GRM188 B3/R6 1C/1A 225
GRM219 B3/R6 1A 475
GRM21B B3/R6 1C/1A 106
*Table 1
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150 W0/Y10°C for one hour and
then set for 24T2 hours at room temperature.
Perform the initial measurement.
Step Temperature (°C) Applying Voltage (V)
1
3
5
7
4
6
8
2
Reference tempereture T2
Reference tempereture T2
20T2
20T2
–55T3 (for R6, C7, C8)/
–25T3 (for B1, B3, F1)
–30T3 (for F5)
85T3 (for B1, B3, F1, R6, F5)
125T3 (for C7)/
105T3 (for C8)
–25T3 (for B1, F1)
85T3 (for B1, F1)
No bias
50% of the rated
voltage
Specifications and Test Methods
35
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
05.12.14
No. Item Specifications Test Method
Deflection12
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2a using an eutectic solder. Then apply a force in the
direction shown in Fig. 3a for 5T1 sec. The soldering should be
done either with an iron or using the reflow method and should
be conducted with care so that the soldering is uniform and free
of defects such as heat shock.
YZ^ª«¯
VZ[§«¬
b
TUWXYZ[\]_`¥¦¨©ª«¬®°±
,
QRSUVWZ
]^
¢£¤¦§¨«
®¯
TUX¥¦©
,QTU¢¥¦
a
U¦
UY¦ª
c
VWZ[§¨«¬
Y]^ª®¯
100
Z]^«®¯
STW¤¥¨
40
ø4.5
Capacitance meter
Flexure : V1
20 50
R230
Pressurizing
speed : 1.0mm/sec.
Pressurize
45 45
Fig.3a
No cracking or marking defects should occur.
Type a b c
GRp03
GRp15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
0.3
0.5
1.2
1.65
2.0
2.9
3.7
5.6
t : 1.6mm
Fig. 2a
Continued from the preceding page.
(in mm)
75% of the terminations is to be soldered evenly and
continuously.
Solderability of
Termination
13
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion) .
Preheat at 80 to 120Dfor 10 to 30 seconds.
After preheating, immerse in an eutectic solder solution for
2T0.5 seconds at 230T5Dor Sn-3.0Ag-0.5Cu solder solution
for 2T0.5 seconds at 245T5°C.
B1, B3, R6, C7, C8 : 0.1 max.
F1, F5 : 0.2 max.
No defects or abnormalities
Within the specified tolerance
Vibration
11
Solder the capacitor on the test jig (glass epoxy board) in the
same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each 3 mutually perpendicular
directions (total of 6 hours).
Appearance
Capacitance
D.F.
(GRp03, GRp15 : t : 0.8mm)
No removal of the terminations or other defects should occur.
Fig. 1a
10
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 1a using an eutectic solder. Then apply 10N*force in
parallel with the test jig for 10T1sec.
The soldering should be done either with an iron or using the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
*5N : GRp15/GRM18, 2N : GRp33
a
b
c
Baked electrode or
copper foil
Solder resist
Type a b c
GRp03
GRp15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
0.3
0.5
1.2
1.65
2.0
2.9
3.7
5.6
Adhesive Strength
of Termination
Continued on the following page.
Specifications and Test Methods
36
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
05.12.14
No. Item Specifications Test Method
17
Durability
Apply 150% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3D. Let sit for 24T2hours at
room temperature, then measure.
The charge/discharge current is less than 50mA.
#Initial measurement
Perform a heat treatment at 150W0/Y10Dfor one hour and
then let sit for 24T2 hours at room temperature. Perform the
initial measurement.
#Measurement after test
Perform a heat treatment at 150W0/Y10Dfor one hour and
then let sit for 24T2 hours at room temperature, then measure.
Appearance
No defects or abnormalities
Capacitance
Change
B1, B3, R6, C7, C8 : Within T12.5%
F1, F5 : Within T30%
D.F. B1, B3, R6, C7, C8 : 0.1 max.
F1, F5 : 0.4 max.
I.R. More than 25Ω· F
Continued from the preceding page.
16
High
Temperature
High
Humidity
(Steady)
Appearance
No defects or abnormalities
Capacitance
Change
B1, B3, R6, C7, C8 : Within T12.5%
F1, F5 : Within T30%
D.F. B1, B3, R6, C7, C8 : 0.2 max.
F1, F5 : 0.4 max.
I.R. More than 12.5Ω· F
Apply the rated voltage at 40T2Dand 90 to 95% humidity for
500T12 hours. The charge/discharge current is less than 50mA.
#Initial measurement
Perform a heat treatment at 150W0/Y10Dfor one hour and
then let sit for 24T2 hours at room temperature. Perform the
initial measurement.
#Measurement after test
Perform a heat treatment at 150W0/Y10Dfor one hour and
then let sit for 24T2 hours at room temperature, then measure.
More than 50Ω· F
B1, B3, R6, C7, C8 : Within T7.5%
F1, F5 : Within T20%
B1, B3, R6, C7, C8 : 0.1 max.
F1, F5 : 0.2 max.
Resistance
to
Soldering
Heat
14
Preheat the capacitor at 120 to 150Dfor 1 minute.
Immerse the capacitor in an eutectic solder or Sn-3.0Ag-0.5Cu
solder solution at 270T5Dfor 10T0.5 seconds. Set at room
temperature for 24T2 hours, then measure.
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150W0/Y10Dfor one hour and
then set at room temperature for 24T2 hours.
Perform the initial measurement.
*Preheating for GRM32/43/55
Appearance
I.R.
No defects
Dielectric
Strength
Capacitance
Change
Q/D.F.
No defects or abnormalities
Temperature
Sudden
Change
15
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
shown in the following table.
Set for 24T2 hours at room temperature, then measure.
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150W0/Y10Dfor one hour and
then set at room temperature for 24T2 hours.
Perform the initial measurement.
No defects or abnormalities
B1, B3, R6, C7, C8 : Within T7.5%
F1, F5 : Within T20%
Appearance
Capacitance
Change
More than 50Ω· F
B1, B3, R6, C7, C8 : 0.1 max.
F1, F5 : 0.2 max.
I.R.
No defects
Dielectric
Strength
D.F.
Step 1 2 3 4
Temp. (D)
Time (min.)
Min.
Operating
Temp. W0/Y3
Room
Temp.
Max.
Operating
Temp. W3/Y0
Room
Temp.
30T32 to 3 30T32 to 3
Step Temperature Time
1
2100 to 120D1 min.
170 to 200D1 min.
Specifications and Test Methods
37
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note C02E.pdf
05.12.14
