LM120QML
LM120QML Series 3-Terminal Negative Regulators
Literature Number: SNVS368
LM120QML
December 16, 2010
Series 3-Terminal Negative Regulators
General Description
The LM120 series are three-terminal negative regulators with
a fixed output voltage of −5V, −12V, and −15V, and up to 1.5A
load current capability. Where other voltages are required, the
LM137 and LM137HV series provide an output voltage range
of −1.2V to −47V.
The LM120 needs only one external component—a compen-
sation capacitor at the output, making them easy to apply.
Worst case guarantees on output voltage deviation due to any
combination of line, load or temperature variation assure sat-
isfactory system operation.
Exceptional effort has been made to make the LM120 Series
immune to overload conditions. The regulators have current
limiting which is independent of temperature, combined with
thermal overload protection. Internal current limiting protects
against momentary faults while thermal shutdown prevents
junction temperatures from exceeding safe limits during pro-
longed overloads.
Although primarily intended for fixed output voltage applica-
tions, the LM120 Series may be programmed for higher out-
put voltages with a simple resistive divider. The low quiescent
drain current of the devices allows this technique to be used
with good regulation.
Features
■Preset output voltage error less than ±3%
■Preset current limit
■Internal thermal shutdown
■Operates with input-output voltage differential down to 1V
■Excellent ripple rejection
■Low temperature drift
■Easily adjustable to higher output voltage
LM120 Series Packages and Power Capability
Rated Design
Package Power Load
Dissipation Current
TO-3 (K) 20W 1.5A
TO-39 (H) 2W 0.5A
Ordering Information
NS Part Number SMD Part Number NS Package Number Package Description
LM120H-5.0/883 H03A 3LD T0–39 Metal Can
LM120H-12/883 H03A 3LD T0–39 Metal Can
LM120H-15/883 H03A 3LD T0–39 Metal Can
LM120K-12/883 K02C 2LD T0–3 Metal Can
LM120K-15/883 K02C 2LD T0–3 Metal Can
LM120KG–5 MD8 (Note 1) Bare Die
LM120KG–12 MD8 (Note 1) Bare Die
LM120KG–15 MD8 (Note 1) Bare Die
Note 1: FOR ADDITIONAL DIE INFORMATION, PLEASE VISIT THE HI REL WEB SITE AT: www.national.com/analog/space/level_die
Connection Diagrams
20150114
Bottom View
Steel Metal Can Package TO-3 (K)
See NS Package Number K02C
20150113
Bottom View
Metal Can Package TO-39 (H)
See NS Package Number H03A
© 2010 National Semiconductor Corporation 201501 www.national.com
LM120QML Series 3-Terminal Negative Regulators
Schematic Diagrams
−5V
20150118
−12V and −15V
20150119
www.national.com 2
LM120QML
Absolute Maximum Ratings (Note 2)
LM120−5 LM120−12 LM120−15
Power Dissipation Internally Limited
Input Voltage −25V −35V −40V
Input-Output Voltage Differential 25V 30V 30V
Junction Temperatures 150°C
Storage Temperature Range −65°C ≤ TA ≤ +150°C
Operating Temperature Range −55°C ≤ TA ≤ +125°C
Lead Temperature (Soldering, 10 sec.) 300°C
Thermal Resistance
θJA
H-Pkg (Still Air @ 0.5W) 191°C/W
H-Pkg (500LF/Min Air flow @ 0.5W) 70°C/W
K-Pkg (Still Air @ 0.5W) 35°C/W
K-Pkg (500LF/Min Air flow @ 0.5W) TBD
θJC
H-Pkg 29°C/W
K-Pkg 3°C/W
ESD Tolerance (Note 4) 4000V
Quality Conformance Inspection
Mil-Std-883, Method 5005 - Group A
Subgroup Description Temp (°C)
1 Static tests at +25
2 Static tests at +125
3 Static tests at -55
4 Dynamic tests at +25
5 Dynamic tests at +125
6 Dynamic tests at -55
7 Functional tests at +25
8A Functional tests at +125
8B Functional tests at -55
9 Switching tests at +25
10 Switching tests at +125
11 Switching tests at -55
12 Settling time at +25
13 Settling time at +125
14 Settling time at -55
3 www.national.com
LM120QML
LM120H-5.0
DC Parameters
The following conditions apply, unless otherwise specified. VIN = −10V, IL = 5mA
Symbol Parameter Conditions Notes Min Max Unit Sub-
groups
IQQuiescent Current VIN = -7V 2.0 mA 1, 2, 3
VIN = -25V 2.0 mA 1, 2, 3
ΔIQQuiescent Current Change
5mA ≤ IL ≤ 0.5A -0.4 0.4 mA 1
-0.5 0.5 mA 2, 3
-25V ≤ VIN ≤ -7V -0.4 0.4 mA 1
-0.5 0.5 mA 2, 3
VOUT Output Voltage
-5.1 -4.9 V 1
VIN = -7.5V -5.2 -4.8 V 1, 2, 3
VIN = -7.5V, IL = 0.5A -5.2 -4.8 V 1, 2, 3
VIN = -25V -5.2 -4.8 V 1, 2, 3
VIN = -25V, IL = 100mA -5.2 -4.8 V 1, 2, 3
RLine Line Regulation -25V ≤ VIN ≤ -7V -25 25 mV 1
-50 50 mV 2, 3
RLoad Load Regulation 5mA ≤ IL ≤ 0.5A -50 50 mV 1
-100 100 mV 2, 3
IOS Short Circuit Current VIN = -25V 0.1 1.5 A 1
RR Ripple Rejection ƒ = 120Hz, IL = 125mA, eI = 1VRMS 54 dB 4
LM120K-5.0
DC Parameters
The following conditions apply, unless otherwise specified. VIN = −10V, IL = 5mA
Symbol Parameter Conditions Notes Min Max Unit Sub-
groups
IQQuiescent Current VIN = -7V 2.0 mA 1, 2, 3
VIN = -25V 2.0 mA 1, 2, 3
ΔIQQuiescent Current Change
5mA ≤ IL ≤ 1.5A -0.4 0.4 mA 1
-0.5 0.5 mA 2, 3
-25V ≤ VIN ≤ -7V -0.4 0.4 mA 1
-0.5 0.5 mA 2, 3
VOUT Output Voltage
-5.1 -4.9 V 1
VIN = -7.5V -5.2 -4.8 V 1, 2, 3
VIN = -7.5V, IL = 1.5A -5.2 -4.8 V 1, 2, 3
VIN = -25V -5.2 -4.8 V 1, 2, 3
VIN = -25V, IL = 1A -5.2 -4.8 V 1, 2, 3
RLine Line Regulation -25V ≤ VIN ≤ -7V -25 25 mV 1
-50 50 mV 2, 3
RLoad Load Regulation 5mA ≤ IL ≤ 1.5A -75 75 mV 1
-100 100 mV 2, 3
IOS Short Circuit Current VIN = -25V 0.4 3.0 A 1
RR Ripple Rejection ƒ = 120Hz, IL = 350mA, eI = 1VRMS 54 dB 4
www.national.com 4
LM120QML
LM120H-12
DC Parameters
The following conditions apply, unless otherwise specified. VIN = −17V, IL = 5mA
Symbol Parameter Conditions Notes Min Max Unit Sub-
groups
IQQuiescent Current VIN = -14V 4.0 mA 1, 2, 3
VIN = -32V 4.0 mA 1, 2, 3
ΔIQQuiescent Current Change
VIN = -17V,
5mA ≤ IL ≤ 200mA
0.4 mA 1
0.5 mA 2, 3
-32V ≤ VIN ≤ -14V 0.4 mA 1
0.5 mA 2, 3
RLoad Load Regulation VIN = -17V, 5mA ≤ IL ≤ 200mA -25 25 mV 1
-50 50 2, 3
RLine Line Regulation -32V ≤ VIN ≤ -14V -10 10 mV 1
-20 20 mV 2, 3
IOS Short Circuit Current VIN = -32V 0.1 1.5 A 1
VOUT Output Voltage
VIN = -17V -12.3 -11.7 V 1
VIN = -32V -12.5 -11.5 V 1, 2, 3
VIN = -32V, IL = 100mA -12.5 -11.5 V 1, 2, 3
VIN = -14.5V -12.5 -11.5 V 1, 2, 3
VIN = -14.5V, IL = 200mA -12.5 -11.5 V 1, 2, 3
RR Ripple Rejection ƒ = 120Hz, IL = 125mA, ei = 1VRMS 56 dB 4
LM120K-12
DC Parameters
The following conditions apply to all the following parameters, unless otherwise specified. VIN = −17V, IL = 5mA
Symbol Parameter Conditions Notes Min Max Unit Sub-
groups
IQQuiescent Current VIN = -14V 4.0 mA 1, 2, 3
VIN = -32V 4.0 mA 1, 2, 3
ΔIQQuiescent Current Change
VIN = -17V, 5mA ≤ IL ≤ 1A 0.4 mA 1
0.5 mA 2, 3
-32V ≤ VIN ≤ -14V 0.4 mA 1
0.5 mA 2, 3
RLoad Load Regulation VIN = -17V, 5mA ≤ IL ≤ 1A -80 80 mV 1, 2, 3
RLine Line Regulation -32V ≤ VIN ≤ -14V -10 10 mV 1
-20 20 mV 2, 3
IOS Short Circuit Current VIN = -32V 0.4 3.0 A 1
VOUT Output Voltage
VIN = -17V -12.3 -11.7 V 1
VIN = -32V -12.5 -11.5 V 1, 2, 3
VIN = -32V, IL = 1A -12.5 -11.5 V 1, 2, 3
VIN = -14.5V -12.5 -11.5 V 1, 2, 3
VIN = -14.5V, IL = 1A -12.5 -11.5 V 1, 2, 3
RR Ripple Rejection ƒ = 120Hz, IL = 350mA, ei = 1VRMS 56 dB 4
5 www.national.com
LM120QML
LM120H-15
DC Parameters
The following conditions apply to all the following parameters, unless otherwise specified. VIN = 20V, IL = 5mA
Symbol Parameter Conditions Notes Min Max Unit Sub-
groups
IQQuiescent Current VIN = -17V 4.0 mA 1, 2, 3
VIN = -35V 4.0 mA 1, 2, 3
ΔIQQuiescent Current Change
VIN = -17V,
5mA ≤ IL ≤ 200mA
0.4 mA 1
0.5 mA 2, 3
-35V ≤ VIN ≤ -17V 0.4 mA 1
0.5 mA 2, 3
RLoad Load Regulation VIN = -20V,
5mA ≤ IL ≤ 200mA
-25 25 mV 1
−50 50 mV 2, 3
RLine Line Regulation -35V ≤ VIN ≤ -17V -10 10 mV 1
-20 20 mV 2, 3
IOS Short Circuit Current VIN = -35V 0.1 1.5 A 1
VOUT Output Voltage
VIN = -20V -15.3 -14.7 V 1
VIN = -35V -15.5 -14.5 V 1, 2, 3
VIN = -35V, IL = 100mA -15.5 -14.5 V 1, 2, 3
VIN = -17.5V -15.5 -14.5 V 1, 2, 3
VIN = -17.5V, IL = 200mA -15.5 -14.5 V 1, 2, 3
RR Ripple Rejection ƒ = 120Hz, IL = 125mA, ei = 1VRMS 56 dB 4
LM120K-15
DC Parameters
The following conditions apply, unless otherwise specified. VIN = 20V, IL = 5mA
Symbol Parameter Conditions Notes Min Max Unit Sub-
groups
IQQuiescent Current VIN = -17V 4.0 mA 1, 2, 3
VIN = -35V 4.0 mA 1, 2, 3
ΔIQQuiescent Current Change
VIN = -17V,
5mA ≤ IL ≤ 1A
0.4 mA 1
0.5 mA 2, 3
-35V ≤ VIN ≤ -17V 0.4 mA 1
0.5 mA 2, 3
RLoad Load Regulation VIN = -20V,
5mA ≤ IL ≤ 1A
-80 80 mV 1, 2, 3
RLine Line Regulation -35V ≤ VIN ≤ -17V -10 10 mV 1
-20 20 mV 2, 3
IOS Short Circuit Current VIN = -35V 0.4 3.0 A 1
VOUT Output Voltage
VIN = -20V -15.3 -14.7 V 1
VIN = -35V -15.5 -14.5 V 1, 2, 3
VIN = -35V, IL = 1A -15.5 -14.5 V 1, 2, 3
VIN = -17.5V -15.5 -14.5 V 1, 2, 3
VIN = -17.5V, IL = 1.5A -15.5 -14.5 V 1, 2, 3
ΔVO / ΔtLong Term Stability (Note 3) 150 mV 1
RR Ripple Rejection ƒ = 120Hz, IL = 350mA, eI = 1VRMS 56 dB 4
www.national.com 6
LM120QML
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 3: Guaranteed parameter, not tested
Note 4: Human body model, 1.5 kΩ in seriew with 100 pF.
Typical Performance Characteristics
Output Voltage vs
Temperature
20150120
Ripple Rejection
(All Types)
20150121
Output Impedance TO-3
20150122
Output Impedance TO-5
20150123
Minimum Input-Output
Differential TO-3
20150124
Minimum Input-Output
Differential TO-5
20150125
7 www.national.com
LM120QML
Quiescent Current vs
Input Voltage
20150126
Quiescent Current vs
Load Current
20150127
Maximum Average Power
Dissipation (TO-3)
20150128
*These curves for LM120. Derate 25°C further for LM320.
Maximum Average Power
Dissipation (TO-5)
20150129
Short Circuit Current
20150132
www.national.com 8
LM120QML
Typical Applications
High Stability 1 Amp Regulator
20150106
Lead and line regulation — 0.01% temperature stability — 0.2%
†Determines Zener current.
††Solid tantalum.
An LM120-12 or LM120-15 may be used to permit higher input voltages, but the regulated output voltage must be at least −15V when using the LM120-12 and
−18V for the LM120-15.
**Select resistors to set output voltage. 2 ppm/°C tracking suggested.
Wide Range Tracking Regulator
20150107
* Resistor tolerance of R1 and R2 determine matching of (+) and (−) inputs.
**Necessary only if raw supply capacitors are more than 3″ from regulators
An LM3086N array may substitute for Q1, D1 and D2 for better stability and
tracking. In the array diode transistors Q5 and Q4 (in parallel) make up D2;
similarly, Q1 and Q2 become D1 and Q3 replaces the 2N2222.
Current Source
20150108
9 www.national.com
LM120QML
Variable Output
20150109
*Optional. Improves transient response and ripple rejection.
SELECT R2 AS FOLLOWS:
LM120-5 −300Ω
LM120-12 −750Ω
LM120-15 −1k
Light Controllers Using Silicon Photo Cells
20150110
*Lamp brightness increases until iI = 5V/R1 (iI can be set as low as 1 μA).
†Necessary only if raw supply filter capacitor is more than 2″ from LM320MP.
20150111
*Lamp brightness increases until iI =iQ (1 mA) + 5V/R1.
†Necessary only if raw supply filter capacitor is more than 2″ from LM320.
Dual Trimmed Supply
20150103
Fixed Regulator
20150102
*Required if regulator is separated from filter capacitor by more than 3″. For
value given, capacitor must be solid tantalum. 25 μF aluminum electrolytic
may be substituted.
†Required for stability. For value given, capacitor must be solid tantalum. 25
μF aluminum electrolytic may be substituted. Values given may be increased
without limit.
For output capacitance in excess of 100 μF, a high current diode from input
to output (1N4001, etc.) will protect the regulator from momentary input
shorts.
www.national.com 10
LM120QML
±15V, 1 Amp Tracking Regulators
20150112
Performance (Typical)
Load Regulation at ΔIL = 1A 10 mV 1 mV
Output Ripple, CIN = 3000 μF,
IL = 1A
100 μVRMS 100 μVRMS
Temperature Stability +50 mV +50 mV
Output Noise 10 Hz ≤ f ≤ 10 kHz 150 μVRMS 150 μVRMS
*Resistor tolerance of R4 and R5 determine matching of (+) and (−) outputs.
**Necessary only if raw supply filter capacitors are more than 2″ from
regulators.
11 www.national.com
LM120QML
Revision History
Date Released Revision Section Changes
12/15/2010 A New release to the corporate format 6 MDS datasheets were converted and merged into
one datasheet compliant to corporate format. Drift
endpoints removed since note used on 883 product.
MDS MNLM120-5.0-K Rev OBL, MNLM120-5.0-H
Rev 0BL, MNLM120-12-K Rev OBL, MNLM120-12-
H Rev 0BL, MNLM120-15-K Rev OBL, &
MNLM120-15-H Rev 0BL will be archived.
www.national.com 12
LM120QML
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (TO-39) (H)
NS Package Number H03A
Steel Metal Can Package TO-3 (K)
NS Package Number K02C
13 www.national.com
LM120QML
Notes
LM120QML Series 3-Terminal Negative Regulators
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products Design Support
Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench
Audio www.national.com/audio App Notes www.national.com/appnotes
Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns
Data Converters www.national.com/adc Samples www.national.com/samples
Interface www.national.com/interface Eval Boards www.national.com/evalboards
LVDS www.national.com/lvds Packaging www.national.com/packaging
Power Management www.national.com/power Green Compliance www.national.com/quality/green
Switching Regulators www.national.com/switchers Distributors www.national.com/contacts
LDOs www.national.com/ldo Quality and Reliability www.national.com/quality
LED Lighting www.national.com/led Feedback/Support www.national.com/feedback
Voltage References www.national.com/vref Design Made Easy www.national.com/easy
PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions
Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero
Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic
PLL/VCO www.national.com/wireless PowerWise® Design
University
www.national.com/training
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: support@nsc.com
Tel: 1-800-272-9959
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
