PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 * * * * * * * * Low Standby-Current Consumption of 1 A Max I2C to Parallel Port Expander Open-Drain Active-Low Interrupt Output 5-V Tolerant I/O Ports Compatible With Most Microcontrollers 400-kHz Fast I2C Bus Address by Three Hardware Address Pins for Use of up to Eight Devices Polarity Inversion Register * * Latched Outputs With High-Current Drive Capability for Directly Driving LEDs Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) RGE PACKAGE (TOP VIEW) 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC SDA SCL A0 P17 P16 P15 P14 P13 P12 P11 P10 24 23 22 21 20 19 P00 P01 P02 P03 P04 P05 1 18 A0 2 3 17 P17 16 P16 4 15 P15 14 P14 5 13 P13 6 7 8 9 10 11 12 P06 P07 GND P10 P11 P12 INT A1 A2 P00 P01 P02 P03 P04 P05 P06 P07 GND A2 A1 INT VCC DB, DBQ, DGV, DW, OR PW PACKAGE (TOP VIEW) SDA SCL FEATURES * DESCRIPTION/ORDERING INFORMATION ORDERING INFORMATION PACKAGE (1) TA Reel of 250 PCA9555DBT QSOP - DBQ Reel of 2500 PCA9555DBQR PCA9555 TVSOP - DGV Reel of 2000 PCA9555DGVR PD9555 Tube of 25 PCA9555DW Reel of 2000 PCA9555DWR Tube of 60 PCA9555PW Reel of 1200 PCA9555PWR Reel of 3000 PCA9555RGER SOIC - DW TSSOP - PW QFN - RGE (1) TOP-SIDE MARKING PCA9555DBR SSOP - DB -40C to 85C ORDERABLE PART NUMBER Reel of 2000 PD9555 PCA9555 PD9555 PD9555 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2006, Texas Instruments Incorporated PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 DESCRIPTION/ORDERING INFORMATION (CONTINUED) This 16-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL), serial data (SDA)]. The PCA9555 consists of two 8-bit Configuration (input or output selection), Input Port, Output Port, and Polarity Inversion (active high or active low operation) registers. At power on, the I/Os are configured as inputs. The system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The polarity of the Input Port register can be inverted with the Polarity Inversion register. All registers can be read by the system master. The system master can reset the PCA9555 in the event of a timeout or other improper operation by utilizing the power-on reset feature, which puts the registers in their default state and initializes the I2C/SMBus state machine. The PCA9555 open-drain interrupt (INT) output is activated when any input state differs from its corresponding Input Port register state and is used to indicate to the system master that an input state has changed. INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the PCA9555 can remain a simple slave device. The device outputs (latched) have high-current drive capability for directly driving LEDs. Although pin-to-pin and I2C-address is compatible with the PCF8575, software changes are required due to the enhancements. The PCA9555 is identical to the PCA9535, except for the inclusion of the internal I/O pullup resistor, which pulls the I/O to a default high when configured as an input and undriven. Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address and allow up to eight devices to share the same I2C bus or SMBus. The fixed I2C address of the PCA9555 is the same as the PCF8575, PCF8575C, and PCF8574, allowing up to eight of these devices in any combination to share the same I2C bus or SMBus. 2 Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 TERMINAL FUNCTIONS NO. SOIC (D), SSOP (DB), QSOP (DBQ), TSSOP (PW), AND TVSOP (DGV) QFN (RGE) 1 22 INT Interrupt output. Connect to VCC through a pullup resistor. 2 23 A1 Address input. Connect directly to VCC or ground. 3 24 A2 Address input. Connect directly to VCC or ground. 4 1 P00 P-port input/output 5 2 P01 P-port input/output 6 3 P02 P-port input/output 7 4 P03 P-port input/output 8 5 P04 P-port input/output 9 6 P05 P-port input/output 10 7 P06 P-port input/output 11 8 P07 P-port input/output 12 9 GND Ground 13 10 P10 P-port input/output 14 11 P11 P-port input/output 15 12 P12 P-port input/output 16 13 P13 P-port input/output 17 14 P14 P-port input/output 18 15 P15 P-port input/output 19 16 P16 P-port input/output 20 17 P17 P-port input/output 21 18 A0 Address input. Connect directly to VCC or ground. 22 19 SCL Serial clock bus. Connect to VCC through a pullup resistor. 23 20 SDA Serial data bus. Connect to VCC through a pullup resistor. 24 21 VCC Supply voltage NAME DESCRIPTION Submit Documentation Feedback 3 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 LOGIC DIAGRAM (POSITIVE LOGIC) INT A0 A1 A2 SCL SDA PCA9555 1 Interrupt Logic LP Filter 21 2 P07-P00 3 22 23 Input Filter I2C Bus Control Shift Register 16 Bits I/O Port P17-P10 Write Pulse VCC GND 4 Read Pulse 24 12 Power-On Reset A. Pin numbers shown are for DB, DBQ, DGV, DW, and PW packages. B. All I/Os are set to inputs at reset. Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 SIMPLIFIED SCHEMATIC OF P-PORT I/Os(1) Data From Shift Register Output Port Register Data Configuration Register Data From Shift Register D Q FF Write Configuration Pulse Write Pulse VCC Q1 CLK Q 100 kW D Q FF I/O Pin CLK Q Output Port Register Q2 Input Port Register D Q FF Read Pulse GND Input Port Register Data CLK Q To INT Data From Shift Register D Q Polarity Register Data FF Write Polarity Pulse CLK Q Polarity Inversion Register (1) At power-on reset, all registers return to default values. I/O Port When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a high-impedance input. The input voltage may be raised above VCC to a maximum of 5.5 V. If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the Output Port register. In this case, there are low-impedance paths between the I/O pin and either VCC or GND. The external voltage applied to this I/O pin should not exceed the recommended levels for proper operation. Submit Documentation Feedback 5 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 I2C Interface The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be connected to a positive supply via a pullup resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. I2C communication with this device is initiated by a master sending a Start condition, a high-to-low transition on the SDA input/output while the SCL input is high (see Figure 1). After the Start condition, the device address byte is sent, MSB first, including the data direction bit (R/W). This device does not respond to the general call address. After receiving the valid address byte, this device responds with an ACK, a low on the SDA input/output during the high of the ACK-related clock pulse. The address inputs (A0-A2) of the slave device must not be changed between the Start and Stop conditions. On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control commands (Start or Stop) (see Figure 2). A Stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the master (see Figure 1). Any number of data bytes can be transferred from the transmitter to the receiver between the Start and the Stop conditions. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before the receiver can send an ACK bit. The device that acknowledges must pull down the SDA line during the ACK clock pulse so that the SDA line is stable low during the high pulse of the ACK-related clock period (see Figure 3). When a slave receiver is addressed, it must generate an ACK after each byte is received. Similarly, the master must generate an ACK after each byte that it receives from the slave transmitter. Setup and hold times must be met to ensure proper operation. A master receiver signals an end of data to the slave transmitter by not generating an acknowledge (NACK) after the last byte has been clocked out of the slave. This is done by the master receiver by holding the SDA line high. In this event, the transmitter must release the data line to enable the master to generate a Stop condition. SDA SCL S P Start Condition Stop Condition Figure 1. Definition of Start and Stop Conditions SDA SCL Data Line Stable; Data Valid Change of Data Allowed Figure 2. Bit Transfer 6 Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Data Output by Transmitter NACK Data Output by Receiver ACK SCL From Master 1 2 8 9 S Clock Pulse for Acknowledgment Start Condition Figure 3. Acknowledgment on I2C Bus Interface Definition BYTE BIT 7 (MSB) 6 5 4 3 2 1 0 (LSB) I2C slave address L H L L A2 A1 A0 R/W P0x I/O data bus P07 P06 P05 P04 P03 P02 P01 P00 P1x I/O data bus P17 P16 P15 P14 P13 P12 P11 P10 Submit Documentation Feedback 7 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Device Address Figure 4 shows the address byte of the PCA9555. R/W Slave Address 0 1 0 0 A2 A1 A0 Fixed Programmable Figure 4. PCA9555 Address Address Reference INPUTS I2C BUS SLAVE ADDRESS A2 A1 A0 L L L 32 (decimal), 20 (hexadecimal) L L H 33 (decimal), 21 (hexadecimal) L H L 34 (decimal), 22 (hexadecimal) L H H 35 (decimal), 23 (hexadecimal) H L L 36 (decimal), 24 (hexadecimal) H L H 37 (decimal), 25 (hexadecimal) H H L 38 (decimal), 26 (hexadecimal) H H H 39 (decimal), 27 (hexadecimal) The last bit of the slave address defines the operation (read or write) to be performed. A high (1) selects a read operation, while a low (0) selects a write operation. Control Register and Command Byte Following the successful acknowledgment of the address byte, the bus master sends a command byte that is stored in the control register in the PCA9555. Three bits of this data byte state the operation (read or write) and the internal register (input, output, polarity inversion or configuration) that will be affected. This register can be written or read through the I2C bus. The command byte is sent only during a write transmission. Once a command byte has been sent, the register that was addressed continues to be accessed by reads until a new command byte has been sent. 0 0 0 0 0 B2 B1 B0 Figure 5. Control Register Bits Command Byte CONTROL REGISTER BITS 8 B2 B1 B0 COMMAND BYTE (HEX) REGISTER PROTOCOL POWER-UP DEFAULT 0 0 0 0x00 Input Port 0 Read byte xxxx xxxx 0 0 1 0x01 Input Port 1 Read byte xxxx xxxx 0 1 0 0x02 Output Port 0 Read/write byte 1111 1111 0 1 1 0x03 Output Port 1 Read/write byte 1111 1111 1 0 0 0x04 Polarity Inversion Port 0 Read/write byte 0000 0000 1 0 1 0x05 Polarity Inversion Port 1 Read/write byte 0000 0000 1 1 0 0x06 Configuration Port 0 Read/write byte 1111 1111 1 1 1 0x07 Configuration Port 1 Read/write byte 1111 1111 Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Register Descriptions The Input Port registers (registers 0 and 1) reflect the incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output by the Configuration register. It only acts on read operation. Writes to these registers have no effect. The default value, X, is determined by the externally applied logic level. Before a read operation, a write transmission is sent with the command byte to indicate to the the I2C device that the Input Port register will be accessed next. Registers 0 and 1 (Input Port Registers) Bit Default Bit Default I0.7 I0.6 I0.5 I0.4 I0.3 I0.2 I0.1 X X X X X X X I0.0 X I1.7 I1.6 I1.5 I1.4 I1.3 I1.2 I1.1 I1.0 X X X X X X X X The Output Port registers (registers 2 and 3) show the outgoing logic levels of the pins defined as outputs by the Configuration register. Bit values in this register have no effect on pins defined as inputs. In turn, reads from this register reflect the value that is in the flip-flop controlling the output selection, not the actual pin value. Registers 2 and 3 (Output Port Registers) Bit Default Bit Default O0.7 O0.6 O0.5 O0.4 O0.3 O0.2 O0.1 O0.0 1 1 1 1 1 1 1 1 O1.7 O1.6 O1.5 O1.4 O1.3 O1.2 O1.1 O1.0 1 1 1 1 1 1 1 1 The Polarity Inversion registers (registers 4 and 5) allow polarity inversion of pins defined as inputs by the Configuration register. If a bit in this register is set (written with 1), the corresponding port pin's polarity is inverted. If a bit in this register is cleared (written with a 0), the corresponding port pin's original polarity is retained. Registers 4 and 5 (Polarity Inversion Registers) Bit Default Bit Default N0.7 N0.6 N0.5 N0.4 N0.3 N0.2 N0.1 0 0 0 0 0 0 0 N0.0 0 N1.7 N1.6 N1.5 N1.4 N1.3 N1.2 N1.1 N1.0 0 0 0 0 0 0 0 0 The Configuration registers (registers 6 and 7) configure the directions of the I/O pins. If a bit in this register is set to 1, the corresponding port pin is enabled as an input with a high-impedance output driver. If a bit in this register is cleared to 0, the corresponding port pin is enabled as an output. Registers 6 and 7 (Configuration Registers) Bit Default Bit Default C0.7 C0.6 C0.5 C0.4 C0.3 C0.2 C0.1 C0.0 1 1 1 1 1 1 1 1 C1.7 C1.6 C1.5 C1.4 C1.3 C1.2 C1.1 C1.0 1 1 1 1 1 1 1 1 Power-On Reset When power (from 0 V) is applied to VCC, an internal power-on reset holds the PCA9555 in a reset condition until VCC has reached VPOR. At that point, the reset condition is released and the PCA9555 registers and I2C/SMBus state machine initialize to their default states. After that, VCC must be lowered to below 0.2 V and then back up to the operating voltage for a power-reset cycle. Submit Documentation Feedback 9 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Interrupt (INT) Output An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time, tiv, the signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original setting, data is read from the port that generated the interrupt or in a Stop event. Resetting occurs in the read mode at the acknowledge (ACK) bit or not acknowledge (NACK) bit after the falling edge of the SCL signal. In a Stop event, INT is cleared after the rising edge of SDA. Interrupts that occur during the ACK or NACK clock pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the I/Os after resetting is detected and is transmitted as INT. Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. Because each 8-bit port is read independently, the interrupt caused by port 0 is not cleared by a read of port 1, or vice versa. INT has an open-drain structure and requires a pullup resistor to VCC. Bus Transactions Data is exchanged between the master and the PCA9555 through write and read commands. Writes Data is transmitted to the PCA9555 by sending the device address and setting the least-significant bit to a logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which register receives the data that follows the command byte. The eight registers within the PCA9555 are configured to operate as four register pairs. The four pairs are input ports, output ports, polarity inversion ports, and configuration ports. After sending data to one register, the next data byte is sent to the other register in the pair (see Figure 6 and Figure 7). For example, if the first byte is sent to output port (register 3), the next byte is stored in Output Port 0 (register 2). There is no limitation on the number of data bytes sent in one write transmission. In this way, each 8-bit register may be updated independently of the other registers. 1 SCL 2 3 4 5 6 7 8 9 Command Byte Slave Address SDA S 0 1 0 0 A2 A1 A0 0 A 0 0 0 0 0 0 Data to Port 0 1 0 R/W Acknowledge From Slave Start Condition 0.7 A Data to Port 1 0.0 Data 0 Acknowledge From Slave A 1.7 1.0 Data 1 A P Acknowledge From Slave Write to Port Data Out from Port 0 tpv Data Valid Data Out from Port 1 tpv Figure 6. Write to Output Port Registers 1 SCL 2 3 4 5 6 7 8 9 1 2 3 Slave Address SDA S 0 1 0 Start Condition 0 A2 A1 A0 4 5 6 7 8 9 1 2 3 Command Byte 0 R/W A 0 0 0 Acknowledge From Slave 0 0 1 1 4 5 6 7 8 1 2 3 Data to Register 0 A MSB Data 0 LSB Acknowledge From Slave Submit Documentation Feedback 4 5 Data to Register Figure 7. Write to Configuration Registers 10 9 A MSB Acknowledge From Slave Data 1 LSB A P PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Reads The bus master first must send the PCA9555 address with the least-significant bit set to a logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which register is accessed. After a restart, the device address is sent again, but this time, the least-significant bit is set to a logic 1. Data from the register defined by the command byte then is sent by the PCA9555 (see Figure 8 through Figure 10). After a restart, the value of the register defined by the command byte matches the register being accessed when the restart occurred. For example, if the command byte references Input Port 1 before the restart, and the restart occurs when Input Port 0 is being read, the stored command byte changes to reference Input Port 0. The original command byte is forgotten. If a subsequent restart occurs, Input Port 0 is read first. Data is clocked into the register on the rising edge of the ACK clock pulse. After the first byte is read, additional bytes may be read, but the data now reflect the information in the other register in the pair. For example, if Input Port 1 is read, the next byte read is Input Port 0. Data is clocked into the register on the rising edge of the ACK clock pulse. There is no limitation on the number of data bytes received in one read transmission, but when the final byte is received, the bus master must not acknowledge the data. Slave Address S 0 1 0 0 A2 Acknowledge From Slave A1 A0 0 Slave Address Acknowledge From Slave Command Byte A A R/W S 0 1 0 0 Data From Lower or Upper Byte of Register Acknowledge From Slave A2 A1 A0 1 Data A MSB LSB A First Byte R/W At this moment, master transmitter becomes master receiver, and slave-receiver becomes slave-transmitter. Acknowledge From Master Data From Upper or Lower Byte of Register MSB No Acknowledge From Master LSB NA Data P Last Byte Figure 8. Read From Register 1 SCL 2 3 4 5 6 7 8 9 I0.x SDA S 0 1 0 0 A2 A1 A0 1 R/W A 7 6 5 Acknowledge From Slave 4 3 I1.x 2 1 0 A 7 6 5 Acknowledge From Master 4 3 I0.x 2 1 0 A 7 6 5 4 3 I1.x 2 Acknowledge From Master 1 0 A 7 6 5 Acknowledge From Master 4 3 2 1 0 1 P No Acknowledge From Master Read From Port 0 Data Into Port 0 Read From Port 1 Data Into Port 1 INT tiv tir A. Transfer of data can be stopped at any time by a Stop condition. When this occurs, data present at the latest acknowledge phase is valid (output mode). It is assumed that the command byte previously has been set to 00 (read Input Port register). B. This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address call and actual data transfer from the P port (see Figure 8 for these details). Figure 9. Read Input Port Register, Scenario 1 Submit Documentation Feedback 11 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 1 SCL 2 3 4 5 6 7 8 9 I0.x SDA S 0 1 0 0 A2 A1 A0 1 R/W A 00 Acknowledge From Slave I1.x A 10 I0.x A 03 Acknowledge From Master Acknowledge From Master I1.x A Read From Port 0 Data Into Port 0 Data 00 Data 01 Data 02 Data 03 tph tps Read From Port 1 Data 10 Data Into Port 1 Data 11 Data 12 INT tiv tir A. Transfer of data can be stopped at any time by a Stop condition. When this occurs, data present at the latest acknowledge phase is valid (output mode). It is assumed that the command byte previously has been set to 00 (read Input Port register). B. This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address call and actual data transfer from the P port (see Figure 8 for these details). Figure 10. Read Input Port Register, Scenario 2 12 Submit Documentation Feedback P No Acknowledge From Master tps tph 1 12 Acknowledge From Master PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range -0.5 6 V VI Input voltage range (2) -0.5 6 V range (2) VO Output voltage IIK Input clamp current VI < 0 -20 mA IOK Output clamp current VO < 0 -20 mA IIOK Input/output clamp current VO < 0 or VO > VCC 20 mA IOL Continuous output low current VO = 0 to VCC 50 mA IOH Continuous output high current VO = 0 to VCC -50 mA ICC JA -0.5 Continuous current through GND -200 Continuous current through VCC 160 Package thermal impedance, junction to free air (3) JP Package thermal impedance, junction to pad Tstg Storage temperature range (1) (2) (3) 6 UNIT DB package 63 DBQ package 61 DGV package 86 DW package 46 PW package 88 V mA C/W RGE package 45 RGE package 1.5 C/W 150 C -65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions MIN MAX 2.3 5.5 SCL, SDA 0.7 x VCC 5.5 A2-A0, P07-P00, P17-P10 0.7 x VCC 5.5 SCL, SDA -0.5 0.3 x VCC A2-A0, P07-P00, P17-P10 -0.5 0.3 x VCC UNIT VCC Supply voltage VIH High-level input voltage VIL Low-level input voltage IOH High-level output current P07-P00, P17-P10 -10 mA IOL Low-level output current P07-P00, P17-P10 25 mA TA Operating free-air temperature 85 C -40 Submit Documentation Feedback V V V 13 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VIK Input diode clamp voltage II = -18 mA VPOR Power-on reset voltage VI = VCC or GND, IO = 0 VCC MIN 2.3 V to 5.5 V -1.2 VPOR IOH = -8 mA P-port high-level output voltage (2) VOH IOH = -10 mA SDA P port (3) IOL INT SCL, SDA II A2-A0 2.3 V 1.8 3V 2.6 4.75 V 4.1 2.3 V 1.7 3V 2.5 3 2.3 V to 5.5 V 8 20 VOL = 0.7 V 2.3 V to 5.5 V 10 24 VOL = 0.4 V 2.3 V to 5.5 V 3 VI = VCC or GND 2.3 V to 5.5 V P port VI = GND 2.3 V to 5.5 V VI = VCC or GND, IO = 0, I/O = inputs, fSCL = 400 kHz, No load VI = GND, IO = 0, I/O = inputs, fSCL = 0 kHz, No load Standby mode VI = VCC, IO = 0, I/O = inputs, fSCL = 0 kHz, No load 20 50 5.5 V 1.1 1.5 3.6 V 0.7 1.3 2.7 V 0.5 1 5.5 V 0.5 1 3.6 V 0.4 0.9 2.7 V 0.25 0.8 2.3 V to 5.5 V (3) 14 A 2.7 V VI = VCC or GND (1) (2) -100 75 SCL VIO = VCC or GND A 30 CI 2.3 V to 5.5 V A 1 3.6 V 2.3 V to 5.5 V P port 1 200 One input at VCC - 0.6 V, Other inputs at VCC or GND Cio 1 100 Additional current in standby mode SDA mA 5.5 V ICC V V 2.3 V to 5.5 V IIL UNIT V VOL = 0.5 V 2.3 V to 5.5 V High inputs 1.65 VOL = 0.4 V VI = VCC Low inputs 1.5 4 P port ICC MAX 4.75 V IIH Operating mode TYP (1) A mA A 1.5 mA 3 7 pF 3 7 3.7 9.5 pF All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25C. Each I/O must be externally limited to a maximum of 25 mA, and each octal (P07-P00 and P17-P10) must be limited to a maximum current of 100 mA, for a device total of 200 mA. The total current sourced by all I/Os must be limited to 160 mA (80 mA for P07-P00 and 80 mA for P17-P10). Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 I2C Interface Timing Requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 11) MIN MAX UNIT 0 400 kHz fscl I2C clock frequency tsch I2C clock high time 0.6 tscl I2C 1.3 tsp I2C spike time tsds I2C serial-data setup time tsdh I2C ticr I2C input rise time 20 + 0.1Cb (1) 300 ns ticf I2C input fall time 20 + 0.1Cb (1) 300 ns tocf I2C (1) 300 tbuf I2C bus free time between Stop and Start 1.3 s tsts I2C Start or repeated Start condition setup 0.6 s tsth I2C Start or repeated Start condition hold 0.6 s tsps I2C 0.6 s tvd(Data) Valid-data time SCL low to SDA output valid 50 tvd(ack) Valid-data time of ACK condition ACK signal from SCL low to SDA (out) low 0.1 Cb I2C bus capacitive load (1) clock low time s 50 100 serial-data hold time output fall time s ns 0 10-pF to 400-pF bus 20 + 0.1Cb Stop condition setup ns ns ns ns 0.9 s 400 pF Cb = total capacitance of one bus line in pF Switching Characteristics over recommended operating free-air temperature range, CL 100 pF (unless otherwise noted) (see Figure 12 and Figure 13) PARAMETER FROM (INPUT) TO (OUTPUT) P port INT 4 s SCL INT 4 s 200 ns MIN MAX UNIT tiv Interrupt valid time tir Interrupt reset delay time tpv Output data valid SCL P port tps Input data setup time P port SCL 150 ns tph Input data hold time P port SCL 1 s Submit Documentation Feedback 15 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 TYPICAL CHARACTERISTICS TA = 25C (unless otherwise noted) SUPPLY CURRENT vs TEMPERATURE STANDBY SUPPLY CURRENT vs TEMPERATURE 55 70 30 SCL = V CC 50 V CC = 5 V ICC - Supply Current - nA 40 f SCL = 400 kHz I/Os Unloaded 35 30 25 V CC = 3.3 V 20 15 10 V CC = 2.5 V 5 0 -50 f SCL = 400 kHz I/Os Unloaded 60 25 ICC - Supply Current - A 45 ICC - Supply Current - A SUPPLY CURRENT vs SUPPLY VOLTAGE 20 V CC = 5 V 15 V CC = 3.3 V 10 40 30 20 10 V CC = 2.5 V 5 50 0 -25 0 25 50 75 0 -50 100 TA - Free-Air Tem perature - C 2.3 -25 0 25 50 75 2.7 3.1 100 3.5 3.9 4.3 4.7 5.1 5.5 V CC - Supply Voltage - V TA - Free-Air Tem perature - C I/O SINK CURRENT vs OUTPUT LOW VOLTAGE I/O SINK CURRENT vs OUTPUT LOW VOLTAGE 30 50 40 V CC = 3.3 V V CC = 2.5 V TA = -40C 20 TA = 25C 15 10 TA = 125C 25 TA = 25C 20 15 10 TA = 125C 5 5 0 0.1 0.2 0.3 0.4 0.5 0.6 0.1 0.4 0.5 225 200 V CC = 5 V, ISINK = 10 m A 150 125 100 V CC = 2.5 V, ISINK = 1 m A 15 10 TA = 125C 0.0 0.1 0.2 0.3 0.4 0.5 0.6 V OL - Output Low Voltage - V I/O SOURCE CURRENT vs OUTPUT HIGH VOLTAGE 50 TA = -40C 25 TA = 25C 20 V CC = 3.3 V 45 30 15 10 TA = 125C 5 V CC = 5 V, ISINK = 1 m A 25 TA = -40C 40 35 TA = 25C 30 25 20 15 10 TA = 125C 5 0 0.0 -25 0 25 50 75 100 0.1 0.2 0.3 0.4 0.5 0.6 (V CC - V OH) - V 0.7 0 0.0 0.1 0.2 0.3 0.4 (V CC - V OH) - V TA - Free-Air Tem perature - C 16 0.6 ISOURCE - I/O Source Current - mA ISOURCE - I/O Source Current - mA V OL - Output Low Voltage - mV 0.3 V CC = 2.5 V 250 0 -50 0.2 35 V CC = 2.5 V, ISINK = 10 m A 50 20 I/O SOURCE CURRENT vs OUTPUT HIGH VOLTAGE 300 75 25 V OL - Output Low Voltage - V I/O OUTPUT LOW VOLTAGE vs TEMPERATURE 175 TA = 25C 30 0 0.0 V OL - Output Low Voltage - V 275 35 5 0 0.0 TA = -40C 40 30 ISINK - I/O Sink Current - mA ISINK - I/O Sink Current - mA TA = -40C V CC = 5 V 45 35 25 ISINK - I/O Sink Current - mA I/O SINK CURRENT vs OUTPUT LOW VOLTAGE Submit Documentation Feedback 0.5 0.6 0.7 PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 TYPICAL CHARACTERISTICS (continued) TA = 25C (unless otherwise noted) I/O SOURCE CURRENT vs OUTPUT HIGH VOLTAGE SUPPLY CURRENT vs NUMBER OF I/Os HELD LOW 300 V CC = 5 V V OH - Output High Voltage - mV TA = 25C TA = 125C 10 5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 200 175 150 V CC = 5 V, IOL = 10 m A 125 100 75 800 700 600 TA = 25C 500 400 300 200 25 100 0 -50 TA = -40C 900 50 0.7 V CC = 5 V 1000 V CC = 2.5 V, IOL = 10 m A 225 (V CC - V OH) - V TA = 125C 0 -25 0 25 50 75 100 TA - Free-Air Tem perature - C 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Num ber of I/Os Held Low OUTPUT HIGH VOLTAGE vs SUPPLY VOLTAGE 6 TA = 25C V OH - Output High Voltage - V 35 30 25 20 15 1100 250 TA = -40C 60 55 50 45 40 1200 275 ICC - Supply Current - A 75 70 65 ISOURCE - I/O Source Current - mA I/O HIGH VOLTAGE vs TEMPERATURE 5 4 IOH = -8 m A 3 IOH = -10 m A 2 1 0 2.3 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 V CC - Supply Voltage - V Submit Documentation Feedback 17 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 PARAMETER MEASUREMENT INFORMATION VCC RL = 1 k SDA DUT CL = 50 pF SDA LOAD CONFIGURATION Three Bytes for Complete Device Programming Stop Condition (P) Start Address Address Condition Bit 7 Bit 6 (S) (MSB) Address Bit 1 tscl R/W Bit 0 (LSB) ACK (A) Data Bit 07 (MSB) Data Bit 10 (LSB) Stop Condition (P) tsch 0.7 x VCC SCL 0.3 x VCC ticr ticf tbuf tsts tPHL tPLH tsp 0.7 x VCC SDA 0.3 x VCC ticf ticr tsth tsdh tsds tsps Repeat Start Condition Start or Repeat Start Condition Stop Condition VOLTAGE WAVEFORMS BYTE DESCRIPTION 1 I2C address 2, 3 P-port data A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr/tf 30 ns. C. All parameters and waveforms are not applicable to all devices. Figure 11. I2C Interface Load Circuit and Voltage Waveforms 18 Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 PARAMETER MEASUREMENT INFORMATION (continued) VCC RL = 4.7 k INT DUT CL = 100 pF INTERRUPT LOAD CONFIGURATION ACK From Slave Start Condition 16 Bits (Two Data Bytes) From Port R/W Slave Address (PCA9555) S 0 1 0 0 A2 A1 A0 1 A 1 2 3 4 A 5 6 7 8 Data 1 ACK From Slave Data 2 Data From Port A Data 3 1 P A tir tir B B INT A tiv tsps A Data Into Port Address Data 1 0.7 x VCC INT 0.3 x VCC SCL Data 2 Data 3 0.7 x VCC R/W tiv A 0.3 x VCC tir 0.7 x VCC Pn 0.7 x VCC INT 0.3 x VCC 0.3 x VCC View A-A View B-B A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr/tf 30 ns. C. All parameters and waveforms are not applicable to all devices. Figure 12. Interrupt Load Circuit and Voltage Waveforms Submit Documentation Feedback 19 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 PARAMETER MEASUREMENT INFORMATION (continued) DUT Pn CL = 100 pF GND P-PORT LOAD CONFIGURATION SCL 0.7 x VCC P00 A P17 0.3 x VCC Slave ACK III III III III SDA Pn tpv (see Note A) Unstable Data Last Stable Bit WRITE MODE (R/W = 0) SCL 0.7 x VCC P00 A tps P17 0.3 x VCC tph 0.7 x VCC Pn 0.3 x VCC READ MODE (R/W = 1) A. CL includes probe and jig capacitance. B. tpv is measured from 0.7 x VCC on SCL to 50% I/O (Pn) output. C. All inputs are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr/tf 30 ns. D. The outputs are measured one at a time, with one transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 13. P-Port Load Circuit and Voltage Waveforms 20 Submit Documentation Feedback PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 PARAMETER MEASUREMENT INFORMATION (continued) VCC RL = 1 k DUT SDA DUT CL = 100 pF CL = 50 pF SDA LOAD CONFIGURATION Pn P-PORT LOAD CONFIGURATION Start SCL ACK or Read Cycle SDA 0.3 y VCC tREC RESET VCC/2 tREC tw Pn VCC/2 tRESET A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr/tf 30 ns. C. The outputs are measured one at a time, with one transition per measurement. D. I/Os are configured as inputs. E. All parameters and waveforms are not applicable to all devices. Figure 14. Reset Load Circuits and Voltage Waveforms Submit Documentation Feedback 21 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 APPLICATION INFORMATION Figure 15 shows an application in which the PCA9555 can be used. Subsystem 1 (e.g., Temperature Sensor) INT VCC (5 V) VCC 10 kW 10 kW 10 kW 24 10 kW 22 SCL Master Controller SDA 23 1 INT Subsystem 2 (e.g., Counter) 2 kW VCC SCL SDA INT P00 P01 P02 A 6 P03 GND RESET 4 5 P04 P05 7 ENABLE 8 9 B PCA9555 VCC P06 P07 3 A2 P10 P11 2 A1 P12 P13 21 A0 P14 P15 P16 GND P17 12 A. Device address is configured as 0100100 for this example. B. P00, P02, and P03 are configured as outputs. C. P01, P04-P07, and P10-P17 are configured as inputs. D. Pin numbers shown are for DB, DBQ, DGV, DW, and PW packages. 10 11 13 14 15 16 17 18 19 20 Figure 15. Typical Application 22 Submit Documentation Feedback Controlled Switch (e.g., CBT Device) ALARM Keypad Subsystem 3 (e.g., Alarm) PCA9555 REMOTE 16-BIT AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS131C - AUGUST 2005 - REVISED JUNE 2006 APPLICATION INFORMATION (continued) Minimizing ICC When I/O Is Used to Control LED When an I/O is used to control an LED, normally it is connected to VCC through a resistor as shown in Figure 15. Because the LED acts as a diode, when the LED is off, the I/O VIN is about 1.2 V less than VCC. The ICC parameter in Electrical Characteristics shows how ICC increases as VIN becomes lower than VCC. For battery-powered applications, it is essential that the voltage of I/O pins is greater than or equal to VCC when the LED is off to minimize current consumption. Figure 16 shows a high-value resistor in parallel with the LED. Figure 17 shows VCC less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O VIN at or above VCC and prevent additional supply current consumption when the LED is off. VCC LED 100 kW VCC Pn Figure 16. High-Value Resistor in Parallel With LED 3.3 V VCC 5V LED Pn Figure 17. Device Supplied by Lower Voltage Submit Documentation Feedback 23 PCA9555 REMOTE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS SCPS131C - AUGUST 2005 - REVISED JUNE 2006 THERMAL PAD MECHANICAL DATA RGE (S-PQFP-N24) 24 Submit Documentation Feedback www.ti.com PACKAGE OPTION ADDENDUM www.ti.com 19-Jun-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty PCA9555DB ACTIVE SSOP DB 24 PCA9555DBQR ACTIVE SSOP/ QSOP DBQ PCA9555DBQRG4 ACTIVE SSOP/ QSOP PCA9555DBR ACTIVE PCA9555DGVR 60 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 24 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR DBQ 24 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR SSOP DB 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE TVSOP DGV 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555DW ACTIVE SOIC DW 24 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555DWR ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555PW ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555PWE4 ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555PWR ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555PWRE4 ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9555RGER ACTIVE QFN RGE 24 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1YEAR PCA9555RHLR PREVIEW QFN RHL 24 1000 25 TBD Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 19-Jun-2006 information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MPDS006C - FEBRUARY 1996 - REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0-8 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins - MO-153 14/16/20/56 Pins - MO-194 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated