SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 D D D D D Member of the Texas Instruments Widebus Family UBT Transceiver Combines D-Type Latches and D-Type Flip-Flops for Operation in Transparent, Latched, or Clocked Mode Compatible With IEEE Std 1149.1-1990 (JTAG) Test Access Port (TAP) and Boundary-Scan Architecture Includes D-Type Flip-Flops and Control Circuitry to Provide Multiplexed Transmission of Stored and Real-Time Data Two Boundary-Scan Cells (BSCs) Per I/O for Greater Flexibility D SCOPE Instruction Set - IEEE Std 1149.1-1990 Required Instructions, Optional INTEST, and P1149.1A CLAMP and HIGHZ - Parallel Signature Analysis (PSA) at Inputs With Masking Option - Pseudorandom Pattern Generation (PRPG) From Outputs - Sample Inputs/Toggle Outputs (TOPSIP) - Binary Count From Outputs - Device Identification - Even-Parity Opcodes 1A2 1A1 1OEAB GND 1LEAB 1CLKAB TDO V CC TMS 1CLKBA 1LEBA 1OEBA GND 1B1 1B2 1B3 PM PACKAGE (TOP VIEW) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1A3 1A4 1A5 GND 1A6 1A7 1A8 1A9 VCC 2A1 2A2 2A3 GND 2A4 2A5 2A6 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 1B4 1B5 1B6 GND 1B7 1B8 1B9 VCC 2B1 2B2 2B3 2B4 GND 2B5 2B6 2B7 2A7 2A8 2A9 GND 2OEAB 2LEAB 2CLKAB TDI VCC TCK 2CLKBA 2LEBA GND 2OEBA 2B9 2B8 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SCOPE, UBT, and Widebus are trademarks of Texas Instruments. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 description The SN74ABT18502 scan test device with an 18-bit universal bus transceiver is a member of the Texas Instruments SCOPE testability IC family. This family of devices supports IEEE Std 1149.1-1990 boundary scan to facilitate testing of complex circuit board assemblies. Scan access to the test circuitry is accomplished via the four-wire test access port (TAP) interface. In the normal mode, this device is an 18-bit universal bus transceiver that combines D-type latches and D-type flip-flops to allow data flow in transparent, latched, or clocked modes. The device can be used either as two 9-bit transceivers or one 18-bit transceiver. The test circuitry can be activated by the TAP to take snapshot samples of the data appearing at the device pins or to perform a self test on the boundary test cells. Activating the TAP in the normal mode does not affect the functional operation of the SCOPE universal bus transceivers. Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch-enable (LEAB and LEBA), and clock (CLKAB and CLKBA) inputs. For A-to-B data flow, the device operates in the transparent mode when LEAB is high. When LEAB is low, the A-bus data is latched while CLKAB is held at a static low or high logic level. Otherwise, if LEAB is low, A-bus data is stored on a low-to-high transition of CLKAB. When OEAB is low, the B outputs are active. When OEAB is high, the B outputs are in the high-impedance state. B-to-A data flow is similar to A-to-B data flow but uses the OEBA, LEBA, and CLKBA inputs. In the test mode, the normal operation of the SCOPE universal bus transceivers is inhibited, and the test circuitry is enabled to observe and control the I/O boundary of the device. When enabled, the test circuitry performs boundary scan test operations according to the protocol described in IEEE Std 1149.1-1990. Four dedicated test pins are used to observe and control the operation of the test circuitry: test data input (TDI), test data output (TDO), test mode select (TMS), and test clock (TCK). Additionally, the test circuitry can perform other testing functions such as parallel signature analysis (PSA) on data inputs and pseudorandom pattern generation (PRPG) from data outputs. All testing and scan operations are synchronized to the TAP interface. Additional flexibility is provided in the test mode through the use of two boundary-scan cells (BSCs) for each I/O pin. This allows independent test data to be captured and forced at either bus (A or B). A PSA/binary count up (PSA/COUNT) instruction is also included to ease the testing of memories and other circuits where a binary count addressing scheme is useful. ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA TOP-SIDE MARKING -40C to 85C LQFP - PM Tray SN74ABT18502PM ABT18502 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (normal mode, each register) INPUTS OUTPUT B OEAB LEAB CLKAB A L L L X L L L B0 L H L L H L H X L L L H X H H H X X X Z A-to-B data flow is shown. B-to-A data flow is similar but uses OEBA, LEBA, and CLKBA. Output level before the indicated steady-state input conditions were established 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 functional block diagram Boundary-Scan Register (BSR) 1LEAB 1CLKAB 60 59 1OEAB 62 1LEBA 54 1CLKBA 1OEBA 55 53 One of Nine Channels 1A1 C1 C1 1D 1D 51 63 C1 1D 1B1 C1 1D 2LEAB 22 2CLKAB 2OEAB 2LEBA 2CLKBA 23 21 28 27 2OEBA 30 One of Nine Channels 2A1 C1 C1 1D 1D 40 10 C1 1D 2B1 C1 1D Bypass Register Boundary-Control Register (BCR) Identification Register (IDR) TDI TMS TCK VCC 24 VCC 56 26 58 Instruction Register (IR) TDO TAP Controller POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 Terminal Functions PIN NAME DESCRIPTION GND Ground TCK Test clock. One of four pins required by IEEE Std 1149.1-1990. Test operations of the device are synchronous to the test clock. Data is captured on the rising edge of TCK and outputs change on the falling edge of TCK. TDI Test data input. One of four pins required by IEEE Std 1149.1-1990. TDI is the serial input for shifting data through the instruction register (IR) or selected data register (DR). An internal pullup forces TDI to a high level if left unconnected. TDO Test data output. One of four pins required by IEEE Std 1149.1-1990. TDO is the serial output for shifting data through the IR or selected DR. TMS Test mode select. One of four pins required by IEEE Std 1149.1-1990. The TMS input directs the device through its TAP controller states. An internal pullup forces TMS to a high level if left unconnected. VCC 1A1-1A9, 2A1- 2A9 Supply voltage Normal-function A-bus I/O ports (see function table for normal-mode logic) 1B1-1B9, 2B1- 2B9 Normal-function B-bus I/O ports (see function table for normal-mode logic) 1CLKAB, 1CLKBA, 2CLKAB, 2CLKBA Normal-function clock inputs (see function table for normal-mode logic) 1LEAB, 1LEBA, 2LEAB, 2LEBA Normal-function latch enables (see function table for normal-mode logic) 1OEAB, 1OEBA, 2OEAB, 2OEBA Normal-function output enables (see function table for normal-mode logic) 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 test architecture Serial test information is conveyed by means of a four-wire test bus or TAP that conforms to IEEE Std 1149.1-1990. Test instructions, test data, and test control signals are all passed along this serial test bus. The TAP controller monitors two signals from the test bus, namely TCK and TMS. The function of the TAP controller is to extract the synchronization (TCK) and state control (TMS) signals from the test bus and generate the appropriate on-chip control signals for the test structures in the device. Figure 1 shows the TAP controller state diagram. The TAP controller is fully synchronous to the TCK signal. Input data is captured on the rising edge of TCK and output data changes on the falling edge of TCK. This scheme ensures that data to be captured is valid for fully one-half of the TCK cycle. The functional block diagram shows the IEEE Std 1149.1-1990 four-wire test bus and boundary-scan architecture and the relationship between the test bus, the TAP controller, and the test registers. As illustrated, the device contains an 8-bit instruction register (IR) and four test data registers (DRs): an 84-bit boundary-scan register (BSR), a 21-bit boundary-control register (BCR), a 1-bit bypass register, and a 32-bit device identification register (IDR). Test-Logic-Reset TMS = H TMS = L TMS = H TMS = H TMS = H Run-Test/Idle Select-DR-Scan Select-IR-Scan TMS = L TMS = L TMS = L TMS = H TMS = H Capture-DR Capture-IR TMS = L TMS = L Shift-DR Shift-IR TMS = L TMS = L TMS = H TMS = H TMS = H TMS = H Exit1-DR Exit1-IR TMS = L TMS = L Pause-DR Pause-IR TMS = L TMS = L TMS = H TMS = H TMS = L Exit2-DR TMS = L Exit2-IR TMS = H Update-DR TMS = H TMS = L TMS = H Update-IR TMS = H TMS = L Figure 1. TAP Controller State Diagram POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 state diagram description The TAP controller is a synchronous finite state machine that provides test control signals throughout the device. The state diagram is shown in Figure 1 and is in accordance with IEEE Std 1149.1-1990. The TAP controller proceeds through its states based on the level of TMS at the rising edge of TCK. As illustrated, the TAP controller consists of sixteen states. There are six stable states (indicated by a looping arrow in the state diagram) and ten unstable states. A stable state is defined as a state the TAP controller can retain for consecutive TCK cycles. Any state that does not meet this criterion is an unstable state. There are two main paths though the state diagram: one to access and control the selected DR and one to access and control the IR. Only one register can be accessed at a time. Test-Logic-Reset The device powers up in the Test-Logic-Reset state. In the stable Test-Logic-Reset state, the test logic is reset and is disabled so that the normal logic function of the device is performed. The IR is reset to an opcode that selects the optional IDCODE instruction, if supported, or the BYPASS instruction. Certain DRs may also be reset to their power-up values. The state machine is constructed such that the TAP controller returns to the Test-Logic-Reset state in no more than five TCK cycles if TMS is left high. TMS has an internal pullup resistor that forces it high if left unconnected or if a board defect causes it to be open circuited. For the SN74ABT18502, the IR is reset to the binary value 10000001, which selects the IDCODE instruction. Each bit in the BSR is reset to logic 0 except bits 83-80, which are reset to logic 1. The BCR is reset to the binary value 000000000000000000010, which selects the PSA test operation with no input masking. Run-Test/Idle The TAP controller must pass through the Run-Test/Idle state (from Test-Logic-Reset) before executing any test operations. The Run-Test/Idle state can also be entered following DR or IR scans. Run-Test/Idle is provided as a stable state in which the test logic may be actively running a test or can be idle. The test operations selected by the BCR are performed while the TAP controller is in the Run-Test/Idle state. Select-DR-Scan, Select-lR-Scan No specific function is performed in the Select-DR-Scan and Select-lR-Scan states, and the TAP controller exits either of these states on the next TCK cycle. These states are provided to allow the selection of either DR scan or IR scan. Capture-DR When a DR scan is selected, the TAP controller must pass through the Capture-DR state. In the Capture-DR state, the selected DR can capture a data value as specified by the current instruction. Such capture operations occur on the rising edge of TCK upon which the TAP controller exits the Capture-DR state. Shift-DR Upon entry to the Shift-DR state, the DR is placed in the scan path between TDI and TDO and, on the first falling edge of TCK, TDO goes from the high-impedance state to an active state. TDO enables to the logic level present in the least significant bit (LSB) of the selected DR. While in the stable Shift-DR state, data is serially shifted through the selected DR on each TCK cycle. The first shift occurs on the first rising edge of TCK after entry to the Shift-DR state (i.e., no shifting occurs during the TCK cycle in which the TAP controller changes from Capture-DR to Shift-DR or from Exit2-DR to Shift-DR). The last shift occurs on the rising edge of TCK upon which the TAP controller exits the Shift-DR state. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 Exit1-DR, Exit2-DR The Exit1-DR and Exit2-DR states are temporary states used to end a DR scan. It is possible to return to the Shift-DR state from either Exit1-DR or Exit2-DR without recapturing the DR. On the first falling edge of TCK after entry to Exit1-DR, TDO goes from the active state to the high-impedance state. Pause-DR No specific function is performed in the stable Pause-DR state, in which the TAP controller can remain indefinitely. The Pause-DR state provides the capability of suspending and resuming DR scan operations without loss of data. Update-DR If the current instruction calls for the selected DR to be updated with current data, such update occurs on the falling edge of TCK following entry to the Update-DR state. Capture-IR When an IR scan is selected, the TAP controller must pass through the Capture-IR state. In the Capture-IR state, the IR captures its current status value. This capture operation occurs on the rising edge of TCK, upon which the TAP controller exits the Capture-IR state. For the SN74ABT18502, the status value loaded in the Capture-IR state is the fixed binary value 10000001. Shift-IR Upon entry to the Shift-IR state, the IR is placed in the scan path between TDI and TDO and, on the first falling edge of TCK, TDO goes from the high-impedance state to an active state. TDO enables to the logic level present in the LSB of the IR. While in the stable Shift-IR state, instruction data is serially shifted through the IR on each TCK cycle. The first shift occurs on the first rising edge of TCK after entry to the Shift-IR state (i.e., no shifting occurs during the TCK cycle in which the TAP controller changes from Capture-IR to Shift-IR or from Exit2-IR to Shift-IR). The last shift occurs on the rising edge of TCK upon which the TAP controller exits the Shift-IR state. Exit1-IR, Exit2-IR The Exit1-IR and Exit2-IR states are temporary states used to end an IR scan. It is possible to return to the Shift-IR state from either Exit1-IR or Exit2-IR without recapturing the IR. On the first falling edge of TCK after entry to Exit1-IR, TDO goes from the active state to the high-impedance state. Pause-IR No specific function is performed in the stable Pause-IR state, in which the TAP controller can remain indefinitely. The Pause-IR state provides the capability of suspending and resuming IR scan operations without loss of data. Update-IR The current instruction is updated and takes effect on the falling edge of TCK following entry to the Update-IR state. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 register overview With the exception of the bypass register and device IDR, any test register can be thought of as a serial shift register with a shadow latch on each bit. The bypass register and device IDR differ in that they contain only a shift register. During the appropriate capture state (Capture-IR for the IR, Capture-DR for DRs), the shift register may be parallel loaded from a source specified by the current instruction. During the appropriate shift state (Shift-IR or Shift-DR), the contents of the shift register are shifted out from TDO while new contents are shifted in at TDI. During the appropriate update state (Update-IR or Update-DR), the shadow latches are updated from the shift register. instruction register (IR) The IR is eight bits long and is used to tell the device what instruction is to be executed. Information contained in the instruction includes the mode of operation (either normal mode, in which the device performs its normal logic function, or test mode, in which the normal logic function is inhibited or altered), the test operation to be performed, which of the four DRs is to be selected for inclusion in the scan path during DR scans, and the source of data to be captured into the selected DR during Capture-DR. Table 4 lists the instructions supported by the SN74ABT18502. The even-parity feature specified for SCOPE devices is supported in this device. Bit 7 of the instruction opcode is the parity bit. Any instructions that are defined for SCOPE devices but are not supported by this device default to BYPASS. During Capture-IR, the IR captures the binary value 10000001. As an instruction is shifted in, this value is shifted out via TDO and can be inspected as verification that the IR is in the scan path. During Update-IR, the value that has been shifted into the IR is loaded into shadow latches. At this time, the current instruction is updated and any specified mode change takes effect. At power up or in the Test-Logic-Reset state, the IR is reset to the binary value 10000001, which selects the IDCODE instruction. The IR order of scan is shown in Figure 2. TDI Bit 7 Parity (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Figure 2. IR Order of Scan 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Bit 2 Bit 1 Bit 0 (LSB) TDO SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 data register (DR) boundary-scan register (BSR) The BSR is 84 bits long. It contains one BSC for each normal-function input pin and two BSCs for each normal-function I/O pin (one for input data and one for output data). The BSR is used 1) to store test data that is to be applied internally to the inputs of the normal on-chip logic and/or externally to the device output pins, and/or 2) to capture data that appears internally at the outputs of the normal on-chip logic and/or externally at the device input pins. The source of data to be captured into the BSR during Capture-DR is determined by the current instruction. The contents of the BSR can change during Run-Test/Idle as determined by the current instruction. At power up or in Test-Logic-Reset, the value of each BSC is reset to logic 0 except BSCs 83-80, which are reset to logic 1, ensuring that these cells, which control A-port and B-port outputs are set to benign values (i.e., if test mode were invoked, the outputs would be at high impedance state). Rest values of other BSCs should be considered indeterminate. The BSR order of scan is from TDI through bits 83-0 to TDO. Table 1 shows the BSR bits and their associated device pin signals. Table 1. BSR Configuration BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL 83 2OEAB 71 2A9-I 53 2A9-O 35 2B9-I 17 2B9-O 82 1OEAB 70 2A8-I 52 2A8-O 34 2B8-I 16 2B8-O 81 2OEBA 69 2A7-I 51 2A7-O 33 2B7-I 15 2B7-O 80 1OEBA 68 2A6-I 50 2A6-O 32 2B6-I 14 2B6-O 79 2CLKAB 67 2A5-I 49 2A5-O 31 2B5-I 13 2B5-O 78 1CLKAB 66 2A4-I 48 2A4-O 30 2B4-I 12 2B4-O 77 2CLKBA 65 2A3-I 47 2A3-O 29 2B3-I 11 2B3-O 76 1CLKBA 64 2A2-I 46 2A2-O 28 2B2-I 10 2B2-O 75 2LEAB 63 2A1-I 45 2A1-O 27 2B1-I 9 2B1-O 74 1LEAB 62 1A9-I 44 1A9-O 26 1B9-I 8 1B9-O 73 2LEBA 61 1A8-I 43 1A8-O 25 1B8-I 7 1B8-O 72 1LEBA 60 1A7-I 42 1A7-O 24 1B7-I 6 1B7-O -- -- 59 1A6-I 41 1A6-O 23 1B6-I 5 1B6-O -- -- 58 1A5-I 40 1A5-O 22 1B5-I 4 1B5-O -- -- 57 1A4-I 39 1A4-O 21 1B4-I 3 1B4-O -- -- 56 1A3-I 38 1A3-O 20 1B3-I 2 1B3-O -- -- 55 1A2-I 37 1A2-O 19 1B2-I 1 1B2-O -- -- 54 1A1-I 36 1A1-O 18 1B1-I 0 1B1-O POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 boundary-control register (BCR) The BCR is 21 bits long. The BCR is used in the context of the RUNT instruction to implement additional test operations not included in the basic SCOPE instruction set. Such operations include PRPG, PSA with input masking, and binary count up (COUNT). Table 5 shows the test operations that are decoded by the BCR. During Capture-DR, the contents of the BCR are not changed. At power up or in Test-Logic-Reset, the BCR is reset to the binary value 000000000000000000010, which selects the PSA test operation with no input masking. The BCR order of scan is from TDI through bits 20-0 to TDO. Table 2 shows the BCR bits and their associated test control signals. Table 2. BCR Configuration BCR BIT NUMBER TEST CONTROL SIGNAL BCR BIT NUMBER TEST CONTROL SIGNAL BCR BIT NUMBER TEST CONTROL SIGNAL 20 MASK2.9 11 MASK1.9 2 OPCODE2 19 MASK2.8 10 MASK1.8 1 OPCODE1 18 MASK2.7 9 MASK1.7 0 OPCODE0 17 MASK2.6 8 MASK1.6 -- -- 16 MASK2.5 7 MASK1.5 -- -- 15 MASK2.4 6 MASK1.4 -- -- 14 MASK2.3 5 MASK1.3 -- -- 13 MASK2.2 4 MASK1.2 -- -- 12 MASK2.1 3 MASK1.1 -- -- bypass register The bypass register is a 1-bit scan path that can be selected to shorten the length of the system scan path, thereby reducing the number of bits per test pattern that must be applied to complete a test operation. During Capture-DR, the bypass register captures a logic 0. The bypass register order of scan is shown in Figure 3. TDI Bit 0 TDO Figure 3. Bypass Register Order of Scan device identification register (IDR) The device IDR is 32 bits long. It can be selected and read to identify the manufacturer, part number, and version of this device. During Capture-DR, the binary value 00000000000000000110000000101111 (0000602F, hex) is captured in the device IDR to identify this device as the TI SN74ABT18502, version 0. The device IDR order of scan is from TDO through bits 31-0 to TDO. Table 3 shows the device IDR bits and their significance. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 Table 3. Device IDR Configuration IDR BIT NUMBER IDENTIFICATION SIGNIFICANCE IDR BIT NUMBER IDENTIFICATION SIGNIFICANCE IDR BIT NUMBER IDENTIFICATION SIGNIFICANCE 31 VERSION3 27 PARTNUMBER15 11 30 VERSION2 26 PARTNUMBER14 10 MANUFACTURER10 MANUFACTURER09 29 VERSION1 25 PARTNUMBER13 9 28 VERSION0 24 PARTNUMBER12 8 -- -- 23 PARTNUMBER11 7 -- -- 22 PARTNUMBER10 6 -- -- 21 PARTNUMBER09 5 -- -- 20 PARTNUMBER08 4 -- -- 19 PARTNUMBER07 3 -- -- 18 PARTNUMBER06 2 -- -- 17 PARTNUMBER05 1 -- -- 16 PARTNUMBER04 0 MANUFACTURER00 LOGIC1 -- -- 15 PARTNUMBER03 -- -- -- -- 14 PARTNUMBER02 -- -- -- -- 13 PARTNUMBER01 -- -- -- -- 12 PARTNUMBER00 -- MANUFACTURER08 MANUFACTURER07 MANUFACTURER06 MANUFACTURER05 MANUFACTURER04 MANUFACTURER03 MANUFACTURER02 MANUFACTURER01 -- Note that for TI products, bits 11- 0 of the device IDR always contains the binary value 000000101111 (02F, hex). instruction-register (IR) opcode The IR opcodes are shown in Table 4. The following descriptions detail the operation of each instruction. Table 4. IR Opcodes BINARY CODE BIT 7 BIT 0 MSB LSB SCOPE OPCODE DESCRIPTION SELECTED DR MODE 00000000 EXTEST Boundary scan Boundary scan Test 10000001 IDCODE Identification read Device identification Normal 10000010 SAMPLE/PRELOAD Sample boundary Boundary scan Normal 00000011 Boundary scan Boundary scan Test 10000100 INTEST BYPASS Bypass scan Bypass Normal 00000101 BYPASS Bypass scan Bypass Normal 00000110 HIGHZ Control boundary to high impedance Bypass Modified test 10000111 Control boundary to 1/0 Bypass Test 10001000 CLAMP BYPASS Bypass scan Bypass Normal 00001001 RUNT Boundary run test Bypass Test 00001010 READBN Boundary read Boundary scan Normal 10001011 READBT Boundary read Boundary scan Test 00001100 CELLTST Boundary self test Boundary scan Normal 10001101 TOPHIP Boundary toggle outputs Bypass Test 10001110 SCANCN BCR scan Boundary control Normal 00001111 SCANCT BCR scan Boundary control Test All others BYPASS Bypass scan Bypass Normal Bit 7 is used to maintain even parity in the 8-bit instruction. The BYPASS instruction is executed in lieu of a SCOPE instruction that is not supported in the SN74ABT18502. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 boundary scan This instruction conforms to the IEEE Std 1149.1-1990 EXTEST and INTEST instructions. The BSR is selected in the scan path. Data appearing at the device input pins is captured in the input BSCs, while data appearing at the outputs of the normal on-chip logic is captured in the output BSCs. Data scanned into the input BSCs is applied to the inputs of the normal on-chip logic, while data scanned into the output BSCs is applied to the device output pins. The device operates in the test mode. bypass scan This instruction conforms to the IEEE Std 1149.1-1990 BYPASS instruction. The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during Capture-DR. The device operates in the normal mode. sample boundary This instruction conforms to the IEEE Std 1149.1-1990 SAMPLE/PRELOAD instruction. The BSR is selected in the scan path. Data appearing at the device input pins is captured in the input BSCs, while data appearing at the outputs of the normal on-chip logic is captured in the output BSCs. The device operates in the normal mode. control boundary to high impedance This instruction conforms to the IEEE Std P1149.1A HIGHZ instruction. The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during Capture-DR. The device operates in a modified test mode in which all device I/O pins are placed in the high-impedance state, the device input pins remain operational, and the normal on-chip logic function is performed. control boundary to 1/0 This instruction conforms to the IEEE Std P1149.1A CLAMP instruction. The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during Capture-DR. Data in the input BSCs is applied to the inputs of the normal on-chip logic, while data in the output BSCs is applied to the device output pins. The device operates in the test mode. boundary run test The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during Capture-DR. The device operates in the test mode. The test operation specified in the BCR is executed during Run-Test/Idle. The five test operations decoded by the BCR are: sample inputs/toggle outputs (TOPSIP), PRPG, PSA, simultaneous PSA and PRPG (PSA/PRPG), and simultaneous PSA/COUNT. boundary read The BSR is selected in the scan path. The value in the BSR remains unchanged during Capture-DR. This instruction is useful for inspecting data after a PSA operation. boundary self test The BSR is selected in the scan path. All BSCs capture the inverse of their current values during Capture-DR. In this way, the contents of the shadow latches can be read out to verify the integrity of both shift-register and shadow-latch elements of the BSR. The device operates in the normal mode. boundary toggle outputs The bypass register is selected in the scan path. A logic-0 value is captured in the bypass register during Capture-DR. Data in the shift-register elements of the selected output BSCs is toggled on each rising edge of TCK in Run-Test/Idle, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK in Run-Test/Idle. Data in the selected input BSCs remains constant and is applied to the inputs of the normal on-chip logic. Data appearing at the device input pins is not captured in the input BSCs. The device operates in the test mode. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 BCR scan The BCR is selected in the scan path. The value in the BCR remains unchanged during Capture-DR. This operation must be performed before a boundary-run test operation to specify which test operation is to be executed. BCR opcodes The BCR opcodes are decoded from BCR bits 2-0 as shown in Table 5. The selected test operation is performed while the RUNT instruction is executed in the Run-Test/Idle state. The following descriptions detail the operation of each BCR instruction and illustrate the associated PSA and PRPG algorithms. Table 5. BCR Opcodes BINARY CODE BIT 2 BIT 0 MSB LSB DESCRIPTION X00 Sample inputs/toggle outputs (TOPSIP) X01 Pseudorandom pattern generation/36-bit mode (PRPG) X10 Parallel signature analysis/36-bit mode (PSA) 011 Simultaneous PSA and PRPG/18-bit mode (PSA/PRPG) 111 Simultaneous PSA and binary count up/18-bit mode (PSA/COUNT) In general, while the control-input BSCs (bits 83-72) are not included in the toggle, PSA, PRPG, or COUNT algorithms, the output-enable BSCs (bits 83- 80 of the BSR) control the drive state (active or high impedance) of the selected device output pins. These BCR instructions are only valid when both bytes of the device are operating in one direction of data flow (that is 1OEAB 1OEBA and 2OEAB 2OEBA) and in the same direction of data flow (that is 1OEAB = 2OEAB and 1OEBA = 2OEBA). Otherwise, the bypass instruction is operated. PSA input masking Bits 20-3 of the BCR are used to specify device input pins to be masked from PSA operations. Bit 20 selects masking for device input pin 2A9 during A-to-B data flow or for device input pin 2B9 during B-to-A data flow. Bit 3 selects masking for device input pins 1A1 or 1B1 during A-to-B or B-to-A data flow, respectively. Bits intermediate to 20 and 3 mask corresponding device input pins in order from most significant to least significant, as indicated in Table 2. When the mask bit that corresponds to a particular device input has a logic-1 value, the device input pin is masked from any PSA operation, meaning that the state of the device input pin is ignored and has no effect on the generated signature. Otherwise, when a mask bit has a logic 0 value, the corresponding device input is not masked from the PSA operation. sample inputs/toggle outputs (TOPSIP) Data appearing at the selected device input pins is captured in the shift-register elements of the selected BSCs on each rising edge of TCK. This data is updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. Data in the shift-register elements of the selected output BSCs is toggled on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 pseudorandom pattern generation (PRPG) A pseudorandom pattern is generated in the shift-register elements of the selected BSCs on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. This data also is updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. Figures 4 and 5 show the 36-bit linear-feedback shift-register algorithms through which the patterns are generated. An initial seed value should be scanned into the BSR before performing this operation. A seed value of all zeroes does not produce additional patterns. 2A9-I 2A8-I 2A7-I 2A6-I 2A5-I 2A4-I 2A3-I 2A2-I 2A1-I 1A9-I 1A8-I 1A7-I 1A6-I 1A5-I 1A4-I 1A3-I 1A2-I 1A1-I 2B9-O 2B8-O 2B7-O 2B6-O 2B5-O 2B4-O 2B3-O 2B2-O 2B1-O 1B9-O 1B8-O 1B7-O 1B6-O 1B5-O 1B4-O 1B3-O 1B2-O 1B1-O = Figure 4. 36-Bit PRPG Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1) 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 2B9-I 2B8-I 2B7-I 2B6-I 2B5-I 2B4-I 2B3-I 2B2-I 2B1-I 1B9-I 1B8-I 1B7-I 1B6-I 1B5-I 1B4-I 1B3-I 1B2-I 1B1-I 2A9-O 2A8-O 2A7-O 2A6-O 2A5-O 2A4-O 2A3-O 2A2-O 2A1-O 1A9-O 1A8-O 1A7-O 1A6-O 1A5-O 1A4-O 1A3-O 1A2-O 1A1-O = Figure 5. 36-Bit PRPG Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 parallel signature analysis (PSA) Data appearing at the selected device input pins is compressed into a 36-bit parallel signature in the shift-register elements of the selected BSCs on each rising edge of TCK. This data is updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. Data in the shadow latches of the selected output BSCs remains constant and is applied to the device outputs. Figures 6 and 7 show the 36-bit linear-feedback shift-register algorithms through which the signature is generated. An initial seed value should be scanned into the BSR prior to performing this operation. 2A8-I 2A7-I 2A6-I 2A5-I 2A4-I 2A3-I 2A2-I 2A1-I 1A9-I 1A8-I 1A7-I 1A6-I 1A5-I 1A4-I 1A3-I 1A2-I 1A1-I 2B9-O 2B8-O 2B7-O 2B6-O 2B5-O 2B4-O 2B3-O 2B2-O 2B1-O 1B9-O 1B8-O 1B7-O 1B6-O 1B5-O 1B4-O 1B3-O 1B2-O 1B1-O MASKX.X 2A9-I = = Figure 6. 36-Bit PSA Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1) 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 2B8-I 2B7-I 2B6-I 2B5-I 2B4-I 2B3-I 2B2-I 2B1-I 1B9-I 1B8-I 1B7-I 1B6-I 1B5-I 1B4-I 1B3-I 1B2-I 1B1-I 2A9-O 2A8-O 2A7-O 2A6-O 2A5-O 2A4-O 2A3-O 2A2-O 2A1-O 1A9-O 1A8-O 1A7-O 1A6-O 1A5-O 1A4-O 1A3-O 1A2-O 1A1-O MASKX.X 2B9-I = = Figure 7. 36-Bit PSA Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 simultaneous PSA and PRPG (PSA/PRPG) Data appearing at the selected device input pins is compressed into an 18-bit parallel signature in the shift-register elements of the selected input BSCs on each rising edge of TCK. This data is updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. At the same time, an 18-bit pseudorandom pattern is generated in the shift-register elements of the selected output BSCs on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. Figures 8 and 9 show the 18-bit linear-feedback shift-register algorithms through which the signature and patterns are generated. An initial seed value should be scanned into the BSR prior to performing this operation. A seed value of all zeroes does not produce additional patterns. 2A8-I 2A7-I 2A6-I 2A5-I 2A4-I 2A3-I 2A2-I 2A1-I 1A9-I 1A8-I 1A7-I 1A6-I 1A5-I 1A4-I 1A3-I 1A2-I 1A1-I 2B9-O 2B8-O 2B7-O 2B6-O 2B5-O 2B4-O 2B3-O 2B2-O 2B1-O 1B9-O 1B8-O 1B7-O 1B6-O 1B5-O 1B4-O 1B3-O 1B2-O 1B1-O MASKX.X 2A9-I = = Figure 8. 18-Bit PSA/PRPG Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1) 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 2B8-I 2B7-I 2B6-I 2B5-I 2B4-I 2B3-I 2B2-I 2B1-I 1B9-I 1B8-I 1B7-I 1B6-I 1B5-I 1B4-I 1B3-I 1B2-I 1B1-I 2A9-O 2A8-O 2A7-O 2A6-O 2A5-O 2A4-O 2A3-O 2A2-O 2A1-O 1A9-O 1A8-O 1A7-O 1A6-O 1A5-O 1A4-O 1A3-O 1A2-O 1A1-O MASKX.X 2B9-I = = Figure 9. 18-Bit PSA/PRPG Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 simultaneous PSA and COUNT (PSA/COUNT) MASKX.X Data appearing at the selected device input pins is compressed into an 18-bit parallel signature in the shift-register elements of the selected input BSCs on each rising edge of TCK. This data is updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. At the same time, an 18-bit binary count-up pattern is generated in the shift-register elements of the selected output BSCs on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. Figures 10 and 11 show the 18-bit linear-feedback shift-register algorithms through which the signature is generated. An initial seed value should be scanned into the BSR prior to performing this operation. 2A9-I 2A8-I 2A7-I 2A6-I 2A5-I 2A4-I 2A3-I 2A2-I 2A1-I 1A9-I 1A8-I 1A7-I 1A6-I 1A5-I 1A4-I 1A3-I 1A2-I 1A1-I 2B8-O 2B7-O 2B6-O 2B5-O 2B4-O 2B3-O 2B2-O 2B1-O MSB 2B9-O = LSB = 1B9-O 1B8-O 1B7-O 1B6-O 1B5-O 1B4-O 1B3-O 1B2-O 1B1-O Figure 10. 18-Bit PSA/COUNT Configuration (1OEAB = 2OEAB = 0, 1OEBA = 2OEBA = 1) 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER MASKX.X SCBS753 - FEBRUARY 2002 2B9-I 2B8-I 2B7-I 2B6-I 2B5-I 2B4-I 2B3-I 2B2-I 2B1-I 1B9-I 1B8-I 1B7-I 1B6-I 1B5-I 1B4-I 1B3-I 1B2-I 1B1-I 2A8-O 2A7-O 2A6-O 2A5-O 2A4-O 2A3-O 2A2-O 2A1-O MSB 2A9-O = LSB = 1A9-O 1A8-O 1A7-O 1A6-O 1A5-O 1A4-O 1A3-O 1A2-O 1A1-O Figure 11. 18-Bit PSA/COUNT Configuration (1OEAB = 2OEAB = 1, 1OEBA = 2OEBA = 0) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 timing description All test operations of the SN74ABT18502 are synchronous to the TCK signal. Data on the TDI, TMS, and normal-function inputs is captured on the rising edge of TCK. Data appears on the TDO and normal-function output pins on the falling edge of TCK. The TAP controller is advanced through its states (as shown in Figure 1) by changing the value of TMS on the falling edge of TCK and then applying a rising edge to TCK. A simple timing example is shown in Figure 12. In this example, the TAP controller begins in the Test-Logic-Reset state and is advanced through its states as necessary to perform one IR scan and one DR scan. While in the Shift-IR and Shift-DR states, TDI is used to input serial data and TDO is used to output serial data. The TAP controller then is returned to the Test-Logic-Reset state. Table 6 explains the operation of the test circuitry during each TCK cycle. Table 6. Explanation of Timing Example TCK CYCLE(S) TAP STATE AFTER TCK DESCRIPTION 1 Test-Logic-Reset TMS is changed to a logic-0 value on the falling edge of TCK to begin advancing the TAP controller toward the desired state. 2 Run-Test/Idle 3 Select-DR-Scan 4 Select-IR-Scan 5 Capture-IR The IR captures the 8-bit binary value 10000001 on the rising edge of TCK as the TAP controller exits the Capture-IR state. 6 Shift-IR TDO becomes active and TDI is made valid on the falling edge of TCK. The first bit is shifted into the TAP on the rising edge of TCK as the TAP controller advances to the next state. Shift-IR One bit is shifted into the IR on each TCK rising edge. With TDI held at a logic-1 value, the 8-bit binary value 11111111 is serially scanned into the IR. At the same time, the 8-bit binary value 10000001 is serially scanned out of the IR via TDO. In TCK cycle 13, TMS is changed to a logic-1 value to end the IR scan on the next TCK cycle. The last bit of the instruction is shifted as the TAP controller advances from Shift-IR to Exit1-IR. 14 Exit1-IR TDO becomes inactive (goes to the high-impedance state) on the falling edge of TCK. 15 Update-IR 16 Select-DR-Scan 17 Capture-DR The bypass register captures a logic-0 value on the rising edge of TCK as the TAP controller exits the Capture-DR state. 18 Shift-DR TDO becomes active and TDI is made valid on the falling edge of TCK. The first bit is shifted into the TAP on the rising edge of TCK as the TAP controller advances to the next state. 19-20 Shift-DR The binary value 101 is shifted in via TDI, while the binary value 010 is shifted out via TDO. 21 Exit1-DR TDO becomes inactive (goes to the high-impedance state) on the falling edge of TCK. 22 Update-DR 23 Select-DR-Scan 7-13 22 24 Select-IR-Scan 25 Test-Logic-Reset The IR is updated with the new instruction (BYPASS) on the falling edge of TCK. In general, the selected DR is updated with the new data on the falling edge of TCK. Test operation completed POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Test-Logic-Reset Select-IR-Scan Select-DR-Scan Update-DR IIIIII IIIIII IIIIII IIIIII Exit1-DR Capture-DR Update-IR Select-DR-Scan II II IIIII IIIII IIIII IIIII Exit1-IR Shift-IR Capture-IR Select-IR-Scan TAP Controller State Select-DR-Scan TDO IIIIIIII IIIIIIII IIIIIIII IIIIIIII Run-Test/Idle TDI Test-Logic-Reset TMS Shift-DR TCK 3-State (TDO) or Don't Care (TDI) Figure 12. Timing Example absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 7 V Input voltage range, VI: Except I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 7 V I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 5.5 V Voltage range applied to any output in the high state or power-off state, VO . . . . . . . . . . . . . . - 0.5 V to 5.5 V Current into any output in the low state, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 50 mA Continuous current through VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576 mA Continuous current through GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1152 mA Package thermal impedance, JA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings can be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 recommended operating conditions (see Note 3) MIN MAX 4.5 5.5 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current VCC - 32 mA Low-level output current 64 mA t /v Input transition rise or fall rate 10 ns / V High-level input voltage 2 V 0.8 Input voltage 0 V V V TA Operating free-air temperature - 40 85 C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = -18 mA IOH = - 3 mA VCC = 5 V, VCC = 4.5 V, VCC = 4.5 V, MIN -1.2 2.5 IOH = - 3 mA IOH = - 24 mA 3 3 2 2 IOH = - 32 mA IOL = 48 mA 2 0.55 VCC = 4 4.5 5V II VCC = 5 5.5 5V V, VI = VCC or GND IIH IIL VCC = 5.5 V, VCC = 5.5 V, VI = VCC VI = GND IOZH IOZL VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.5 V IOZPU VCC = 0 to 2 V, VO = 2.7 V or 0.5 V, IOZPD VCC = 2 V to 0, VO = 2.7 V or 0.5 V, Ioff ICEX IO VCC = 0, VCC = 5.5 V, VI or VO 4.5 V VO = 5.5 V Outputs high VCC = 5.5 V, VO = 2.5 V ICC Ci Cio VCC = 5.5 V, IO = 0, VI = VCC or GND IOL = 64 mA A or B ports UNIT -1.2 V V 0.55 CLK, LE, OE, TCK A or B ports 1 1 100 100 V A TDI, TMS 10 10 A TDI, TMS -150 -150 A 50 50 A - 50 - 50 A OE = 0.8 V 50 50 A OE = 0.8 V 50 50 A 100 450 A 50 50 A -200 mA -110 -200 Outputs high - 50 3.5 5.5 5.5 Outputs low 33 38 38 Outputs disabled 2.9 Control inputs A or B ports - 50 5 5 50 50 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 mA A 3 pF 10 pF Co VO = 2.5 V or 0.5 V TDO 8 All typical values are at VCC = 5 V. The parameters IOZH and IOZL include the input leakage current. Not more than one output should be tested at a time, and the duration of the test should not exceed one second. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. 24 MAX 0.55 VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V MIN 2.5 VOL ICC TA = 25C TYP MAX pF SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (normal mode) (see Figure 13) fclock Clock frequency tw Pulse duration CLKAB or CLKBA MHz 3.5 3.5 ns 4 CLK high A before LEAB or B before LEBA Hold time UNIT 100 LEAB or LEBA high Setup time th MAX 0 CLKAB or CLKBA high or low A before CLKAB or B before CLKBA tsu MIN CLK low ns 3.5 2 A after CLKAB or B after CLKBA 0 A after LEAB or B after LEBA 2 ns timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (test mode) (see Figure 13)123 MIN MAX UNIT fclock tw Clock frequency TCK 0 50 MHz Pulse duration TCK high or low 8 A, B, CLK, LE, or OE before TCK 4.5 tsu Setup time TDI before TCK 7.5 TMS before TCK th td tr ns ns 3 A, B, CLK, LE, or OE after TCK 0.5 TDI after TCK 0.5 TMS after TCK 0.5 Delay time Power up to TCK 50 ns Rise time VCC power up 1 s Hold time ns switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (normal mode) (see Figure 13) PARAMETER fmax tPLH tPHL tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) CLKAB or CLKBA A or B B or A CLKAB or CLKBA B or A LEAB or LEBA B or A OEAB or OEBA B or A OEAB or OEBA B or A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 VCC = 5 V, TA = 25C MIN MAX MIN TYP 100 130 2 3.8 5.6 2 6 2 3.8 5.6 2 6 2.5 4.7 5.7 2.5 6 2.5 4.7 5.7 2.5 6 2.5 4.9 6.4 2.5 7 2.5 4.9 6.5 2.5 7 UNIT MAX 100 MHz 2 4.9 6.3 2 7 2.5 5.6 7.2 2.5 8 3 6.1 7.8 3 8.8 2.5 4.8 6.5 2.5 7.3 ns ns ns ns ns 25 SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (test mode) (see Figure 13)1234 PARAMETER fmax tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ 26 FROM (INPUT) TO (OUTPUT) TCK TCK A or B TCK TDO TCK A or B TCK TDO TCK A or B TCK TDO POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 VCC = 5 V, TA = 25C MIN MAX MIN TYP 50 90 2.5 9.1 11.4 2.5 13.5 2.5 9.1 10.8 2.5 12.4 2 3.8 5.1 2 5.6 2 3.8 5.3 2 6 UNIT MAX 50 MHz 4.5 9.5 11.5 4.5 13.4 5 10.1 12.2 5 14 2.5 4.6 5.9 2.5 6.8 3 5.2 6.8 3 7.5 4 11.6 14.3 4 16.3 3.5 11.1 13.6 3.5 15.3 3 5.3 7.2 3 7.6 3 5.2 6.8 3 7.6 ns ns ns ns ns ns SN74ABT18502 SCAN TEST DEVICE WITH 18-BIT REGISTERED BUS TRANSCEIVER SCBS753 - FEBRUARY 2002 PARAMETER MEASUREMENT INFORMATION 7V S1 500 From Output Under Test Open GND CL = 50 pF (see Note A) 500 TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT FOR OUTPUTS 3V 1.5 V Timing Input 0V tw tsu 3V Input 1.5 V 3V 1.5 V Data Input 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V 0V tPHL 1.5 V 1.5 V tPLH VOH Output 1.5 V 1.5 V 0V 1.5 V VOL tPLZ Output Waveform 1 S1 at 7 V (see Note C) VOL tPHL 1.5 V tPZL VOH Output 3V Output Control 1.5 V tPLH 1.5 V 0V VOLTAGE WAVEFORMS PULSE DURATION Input (see Note B) th Output Waveform 2 S1 at Open (see Note C) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NON-INVERTING OUTPUTS 1.5 V tPZH 3.5 V VOL + 0.3 V VOL tPHZ 1.5 V VOH - 0.3 V VOH 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. D. The outputs are measured one at a time with one transition per measurement. Figure 13. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 27 PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74ABT18502PM ACTIVE LQFP PM 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR SN74ABT18502PMG4 ACTIVE LQFP PM 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR SN74ABT18502PMR ACTIVE LQFP PM 64 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR SN74ABT18502PMRG4 ACTIVE LQFP PM 64 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74ABT18502 : * Military: SN54ABT18502 NOTE: Qualified Version Definitions: * Military - QML certified for Military and Defense Applications Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74ABT18502PMR Package Package Pins Type Drawing LQFP PM 64 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 330.0 24.4 Pack Materials-Page 1 13.0 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 13.0 2.1 16.0 24.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74ABT18502PMR LQFP PM 64 1000 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MTQF008A - JANUARY 1995 - REVISED DECEMBER 1996 PM (S-PQFP-G64) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 0,08 M 33 48 49 32 64 17 0,13 NOM 1 16 7,50 TYP Gage Plane 10,20 SQ 9,80 12,20 SQ 11,80 0,25 0,05 MIN 0- 7 0,75 0,45 1,45 1,35 Seating Plane 0,08 1,60 MAX 4040152 / C 11/96 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Falls within JEDEC MS-026 May also be thermally enhanced plastic with leads connected to the die pads. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated