Data Sheet PS9001 R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE, 5-PIN SOP (LSO5 WITH 8mm CREEPAGE DISTANCE) PHOTOCOUPLER DESCRIPTION The PS9001 is an optically coupled high-speed, active low type isolator containing an AlGaAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. FEATURES Long creepage distance (8 mm MIN) High common mode transient immunity (CMH, CML = 50 kV/s MIN.) Operating Ambient Temperature (125 C MAX.) High-speed response (tPHL = 100 ns MAX., tPLH = 100 ns MAX.) Embossed tape product : PS9001-F3 : 3000 pcs/reel Pb-Free product Safety standards UL approved: UL1577, Double protection CSA approved: CAN/CSA-C22.2 No. 62368-1, Reinforced insulation VDE approved: DIN EN 60747-5-5 (Option) PIN CONNECTION (Top View) 5 4 3 1. Anode 2. Cathode 3. GND 4. VO 5. VCC 1 2 APPLICATIONS Measurement equipment FA Network Start of mass production Oct.2015 R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 1 of 15 PS9001 Chapter Title PACKAGE DIMENSIONS (UNIT: mm) Weight : 0.119g (typ.) PHOTOCOUPLER CONSTRUCTION Parameter MIN. Air Distance Creepage Distance 8.0 mm 8.0 mm Isolation Distance 0.15 mm R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 2 of 15 PS9001 Chapter Title BLOCK DIAGRAM (Unit: mm) MARKING EXAMPLE R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 3 of 15 PS9001 Chapter Title ORDERING INFORMATION Part Number Order Number PS9001 PS9001-F3 PS9001-Y-AX PS9001-Y-F3-AX PS9001-V PS9001-Y-V-AX PS9001-V-F3 PS9001-Y-V-F3-AX Note: Solder Plating Specification Pb-Free and Halogen Free (Ni/Pd/Au) Packing Style Safety Standard Approval 20 pcs (Tape 20 pcs cut) Embossed Tape 3 000 Standard products (UL, CSA approved) pcs/reel 20 pcs (Tape 20 pcs cut) Application Part Number*1 PS9001 UL, CSA, DIN EN 60747-5-5 approved Embossed Tape 3 000 pcs/reel *1. For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified) Diode Parameter Forward Current *1 Symbol IF Ratings 25 Unit mA Reverse Voltage Supply Voltage VR VCC 5 -0.5 to 7 V V Detector Output Voltage Output Current VO IO -0.5 to 7 20 V mA Power Dissipation Isolation Voltage *2 PC BV 100 5000 mW Vr.m.s. Operating Ambient Temperature Storage Temperature TA Tstg 40 to +125 55 to +150 C C Notes: *1. Reduced to 0.325 mA/C at TA = 85C or more. *2. AC voltage for 1 minute at TA = 25C, RH = 60% between input and output. Pins 1-2 shorted together, 3-5 shorted together. RECOMMENDED OPERATING CONDITIONS Symbol MIN. TYP. MAX. Unit High Level Input Voltage Low Level Input Current Parameter VF IF 2 8 - 10 0.8 12 V mA Supply Voltage Operating Ambient Temperature VCC TA 4.5 -40 5.0 - 5.5 125 V C R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 4 of 15 PS9001 Chapter Title ELECTRICAL CHARACTERISTICS (TA = 40 to +125C, Vcc=5V unless otherwise specified) Parameter Diode Detector Coupled Symbol Conditions MIN. TYP. *1 MAX. Unit 1.35 1.56 1.75 10 A 50 A Forward Voltage Reverse Current VF IR IF = 10 mA, TA = 25C VR = 3 V, TA = 25C V Terminal Capacitance High Level Output Current Ct IOH f = 1 MHz, VF = 0 V, TA = 25C VCC = VO = 5.5 V, VF = 0.8 V 30 Low Level Output Voltage High Level Supply Current VOL ICCH IF = 4 mA, IOL = 5 mA VCC = 5.5 V, IF = 0 mA, VO = open 0.1 1.4 0.6 2.0 V mA Low Level Supply Current ICCL 1.4 2.0 mA Threshold Input Voltage (H L) IFHL VCC = 5.5 V, IF = 10mA, VO = open VO = 0.6V,IO = 5mA 1.2 4.0 mA Propagation Delay Time (H L) *2 tPHL 35 100 ns Propagation Delay Time tPLH IF = 10 mA, RL = 1.9 k , CL = 15 pF, VTHHL = 1.5 V, VTHLH = 1.5 V 65 100 ns 30 50 ns 60 ns pF (L H) *2 Notes: Pulse Width Distortion (PWD) Propagation Delay Skew tPHLtPLH tpsk Common Mode Transient Immunity at High Level Output *3 CMH TA = 25C, IF = 0 mA, VO > 1.5 V, RL = 1.9 k, VCM = 1.5 kV, CL = 15 pF 50 kV/s Common Mode Transient Immunity at Low Level Output *3 CML TA = 25C, IF = 10 mA, VO < 1.5 V, RL = 1.9 k, VCM = 1.5 kV, CL = 15 pF 50 kV/s *1. Typical values at TA = 25C *2. Test circuit for tPHL and tPLH Pulse input (IF) (PW = 10 s, Duty cycle = 1/10) Input (monitor) VCC = 5 V 0.1 F RL = 1.9 k CL = 15 pF VO (monitor) 47 Remark CL includes probe and stray wiring capacitance. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 5 of 15 PS9001 Chapter Title *3. Test circuit for common mode transient immunity IF SW VCC = 5 V 0.1 F B A C = 0.01 F 10% RL = 1.9 k CL = 15 pF 1.5 kV VCM 90% VO (monitor) 0V tr VO (Switch A : IF = 0 mA) VCM + VCM = 1.5 kV Remark VO (Switch B : IF = 10 mA) tf VOH 1.5 V 1.5 V VOL CL includes probe and stray wiring capacitance. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 6 of 15 PS9001 Chapter Title TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified) FORWARD CURRENT vs. FORWARD VOLTAGE 100 30 Forward Current IF (mA) 25 20 15 10 5 0 85C 50C 100C 0 25 50 75 100 0.1 1.5 2 2.5 OUTPUT VOLTAGE vs. FORWARD CURRENT 6.0 Vcc = 5.5V Output Voltage VO (V) ICCL(IF = 10mA) ICCH(IF = 0mA) -25 0 25 50 75 100 4.0 RL = 1.0k 3.0 2.0 3.9k 1.9k 1.0 0.0 125 Vcc = 5.5V 5.0 1 0 2 3 4 Ambient Temperature TA (C) Forward Current IF (mA) LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE 4.0 Vcc = 5.5V IF = 4mA 0.4 0.3 0.0 -50 1 SUPPLY CURRENT vs. AMBIENT TEMPERATURE 0.5 0.1 -20C -40C 0.01 1 150 0.5 0.2 25C 125C Forward Voltage VF (V) 1.0 0.0 -50 10 Ambient Temperature TA (C) 2.0 1.5 125 IOL = 5mA IOL = 2mA -25 0 25 50 75 100 125 Ambient Temperature TA (C) Threshold Input Current IFHL (mA) Low Level Output Voltage VOL (V) High Level Supply Current ICCH (mA) Low Level Supply Current ICCL (mA) Maximum Forward Current IF (mA) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE Vcc = 5.0V VO = 0.6V 3.0 2.0 1.0 0.0 -50 -25 0 25 50 75 100 125 Ambient Temperature TA (C) Remark The graphs indicate nominal characteristics. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 7 of 15 PS9001 Chapter Title 100 75 Vcc = 5.0V IF = 10mA RL = 1.9K PROPAGATION DELAY TIME vs. FORWARD CURRENT tPLH tPHL 50 25 |tPLH-tPHL| 0 -50 -25 0 25 50 75 100 125 Ambient Temperature TA (C) Propagation Delay Time tPHL, tPLH (ns) Propagation Delay Time tPHL, tPLH (ns) Pulse Wide Distortion |tPHL-tPLH| (ns) PROPAGATION DELAY TIME, PULSE WIDE DISTORTION vs. AMBIENT TEMPERATURE 100 Vcc = 5.0V RL = 1.9K tPLH 75 50 tPHL 25 0 5 10 15 20 25 Forward Current IF (mA) Remark The graphs indicate nominal characteristics. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 8 of 15 PS9001 Chapter Title TAPING SPECIFICATIONS (UNIT: mm) Tape Direction Outline and Dimensions (Taps) Outline and Dimensions (Reel) Packing:3000 pcs/reel R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 9 of 15 PS9001 Chapter Title RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) Remark All dimensions in this figure must be evaluated before use. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 10 of 15 PS9001 Chapter Title NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220C * Time to preheat temperature from 120 to 180C * Number of reflows * Flux 260C or below (package surface temperature) 10 seconds or less 60 seconds or less 12030 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (C) (heating) to 10 s 260C MAX. 220C to 60 s 180C 120C 12030 s (preheating) Time (s) (2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260C or below (molten solder temperature) 10 seconds or less 120C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron * Peak Temperature (lead part temperature) 350C or below * Time (each pins) 3 seconds or less * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and halogens-based (chlorine-based) cleaning solvent . 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler's input and output at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 11 of 15 PS9001 Chapter Title USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of more than 0.1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. 4. Do not use adhesives or coating materials including halogens to fix this device. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 12 of 15 PS9001 Chapter Title SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Climatic test class (IEC 60068-1/DIN EN 60068-1) Rating Unit 40/125/21 Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.6 UIORM., Pd 5 pC UIORM Upr 1 130 1 808 Vpeak Vpeak Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 UIORM., Pd 5 pC Upr 2 119 Vpeak Highest permissible overvoltage UTR 8 000 Vpeak Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) 2 Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11)) CTI 400 Storage temperature range Tstg -55 to +150 C Operating temperature range TA -40 to +125 C Ris MIN. Ris MIN. 1012 1011 Tsi Isi Psi 175 400 700 C mA mW Ris MIN. 109 Material group (DIN EN 60664-1 VDE0110 Part 1) II Isolation resistance, minimum value VIO = 500 V dc at TA = 25C VIO = 500 V dc at TA MAX. at least 100C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = Tsi Total Power Dissipation Psi (mW) Input Current Isi (mA) Dependence of maximum safety ratings with package temperature 1000 900 800 700 600 Psi: Total Power Dissipation 500 400 300 Isi: Input Current 200 100 0 0 25 50 75 100 125 150 175 200 Package temp Tsi (C) R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 13 of 15 PS9001 Chapter Title Method a) Destructive Test, Type and Sample Test UIOTM =8000V V Upr =1808V UIORM =1130V t3 tini t1 t2 tm t4 t ttest t1,t2 = 1 to 10 sec t3,t4 = 1 sec tm(PARTIAL DISCHARGE)= 10 sec ttest = 12 sec tini = 60 sec Method b) Non-destructive Test, 100% Production Test Upr =2119V V UIORM =1130V ttest t3 tm t t4 t3,t4 = 0.1 sec tm(PARTIAL DISCHARGE)= 1.0 sec ttest = 1.2 sec R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 14 of 15 PS9001 Caution Chapter Title GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. R08DS0130EJ0101 Rev.1.01 Oct 29, 2018 Page 15 of 15 Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation or any other use of the circuits, software, and information in the design of your product or system. Renesas Electronics disclaims any and all liability for any losses and damages incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics hereby expressly disclaims any warranties against and liability for infringement or any other claims involving patents, copyrights, or other intellectual property rights of third parties, by or arising from the use of Renesas Electronics products or technical information described in this document, including but not limited to, the product data, drawings, charts, programs, algorithms, and application examples. 3. 4. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You shall not alter, modify, copy, or reverse engineer any Renesas Electronics product, whether in whole or in part. Renesas Electronics disclaims any and all liability for any losses or damages incurred by you or third parties arising from such alteration, modification, copying or reverse engineering. 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The intended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; industrial robots; etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control (traffic lights); large-scale communication equipment; key financial terminal systems; safety control equipment; etc. Unless expressly designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are not intended or authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems; surgical implantations; etc.), or may cause serious property damage (space system; undersea repeaters; nuclear power control systems; aircraft control systems; key plant systems; military equipment; etc.). Renesas Electronics disclaims any and all liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user's manual or other Renesas Electronics document. 6. When using Renesas Electronics products, refer to the latest product information (data sheets, user's manuals, application notes, "General Notes for Handling and Using Semiconductor Devices" in the reliability handbook, etc.), and ensure that usage conditions are within the ranges specified by Renesas Electronics with respect to maximum ratings, operating power supply voltage range, heat dissipation characteristics, installation, etc. Renesas Electronics disclaims any and all liability for any malfunctions, failure or accident arising out of the use of Renesas Electronics products outside of such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of Renesas Electronics products, semiconductor products have specific characteristics, such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Unless designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are not subject to radiation resistance design. You are responsible for implementing safety measures to guard against the possibility of bodily injury, injury or damage caused by fire, and/or danger to the public in the event of a failure or malfunction of Renesas Electronics products, such as safety design for hardware and software, including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult and impractical, you are responsible for evaluating the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. You are responsible for carefully and sufficiently investigating applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive, and using Renesas Electronics products in compliance with all these applicable laws and regulations. Renesas Electronics disclaims any and all liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technologies shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You shall comply with any applicable export control laws and regulations promulgated and administered by the governments of any countries asserting jurisdiction over the parties or transactions. 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, or any other party who distributes, disposes of, or otherwise sells or transfers the product to a third party, to notify such third party in advance of the contents and conditions set forth in this document. 11. This document shall not be reprinted, reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its directly or indirectly controlled subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. (Rev.4.0-1 November 2017) http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. California Eastern Laboratories, Inc. 4590 Patrick Henry Drive, Santa Clara, California 95054-1817, U.S.A. Tel: +1-408-919-2500, Fax: +1-408-988-0279 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-651-700, Fax: +44-1628-651-804 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Dusseldorf, Germany Tel: +49-211-6503-0, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. Room 1709 Quantum Plaza, No.27 ZhichunLu, Haidian District, Beijing, 100191 P. R. China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 301, Tower A, Central Towers, 555 Langao Road, Putuo District, Shanghai, 200333 P. R. China Tel: +86-21-2226-0888, Fax: +86-21-2226-0999 Renesas Electronics Hong Kong Limited Unit 1601-1611, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2265-6688, Fax: +852 2886-9022 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei 10543, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre, Singapore 339949 Tel: +65-6213-0200, Fax: +65-6213-0300 Renesas Electronics Malaysia Sdn.Bhd. Unit 1207, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics India Pvt. Ltd. No.777C, 100 Feet Road, HAL 2nd Stage, Indiranagar, Bangalore 560 038, India Tel: +91-80-67208700, Fax: +91-80-67208777 Renesas Electronics Korea Co., Ltd. 17F, KAMCO Yangjae Tower, 262, Gangnam-daero, Gangnam-gu, Seoul, 06265 Korea Tel: +82-2-558-3737, Fax: +82-2-558-5338 (c) 2018 Renesas Electronics Corporation. All rights reserved. Colophon 7.0