www.element14.com
www.farnell.com
www.newark.com
www.cpc.co.uk
Page <1> V1.224/10/12
Heat Shrink Tubing
Description
Very low shrink temperature, exible, halogen free, polyolen thin wall heat
shrink tubing.
Applications
This thin wall heat shrink tubing is manufactured with modied radiation cross-linked
polyolen. The specially designed halogen free formulation makes the tubing very exible and
able to shrink at a lower temperature. It is suitable for applications where temperature sensitive
components protection (e.g. PVC jacketed wire and cable) and quick shrinkage is required. The
ammability of the tubing meets the automotive ame propagation standard MVSS3 302. This
tubing has good mechanical and electrical performances.
Specications:
Operating temperature : -40°C to +125°C
Min. Shrink Temperature : 65°C
Shrink Ratio : 2 : 1
Colour : Black
Technical Data
Property Typical Data
Tensile Strength 15MPa
Ultimate Elongation (%) 450
Longitudinal Shrinkage (%) +/- 5
Heat Aging Tensile Strength 11MPa
Ultimate Elongation (%) 300
Flammability Pass
Dielectric Strength (kv/mm) 20
Volume Resistivity (ohm-cm) 1 × 1014
www.element14.com
www.farnell.com
www.newark.com
www.cpc.co.uk
Page <2> V1.224/10/12
Heat Shrink Tubing
Important Notice : This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted
for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any
error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any
assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the
Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence.
pro - POWER is the registered trademark of the Group. © Premier Farnell plc 2012.
Description Size
mm (Inch)
As Supplied
I.D. (mm)
After Recovery
Max. I.D. (mm)
Length
(Imperial)
Length
(Metric) Part Number
Thin Wall Heat Shrink
Tubing
1.6 (1/16) 1.4 ±0.2 0.8 328 ft 100m HFTW13633
2.4 (3/32) 2.4 ±0.2 1.2 328 ft 100m HFTW13634
3.2 (1/8) 3.4 ±0.2 1.6 328 ft 100m HFTW13635
4.8 (3/16) 4.9 ±0.2 2.4 328 ft 100m HFTW13636
6.4 (1/4) 6.5 ±0.2 3.2 328 ft 100m HFTW13637
9.5 (3/8) 9.5 ±0.3 4.8 328 ft 100m HFTW13638
12.7 (1/2) 12.5 ±0.3 6.4 328 ft 100m HFTW13639
19.1 (3/4) 18.5 ±0.4 9.5 328 ft 100m HFTW13640
25.4 (1) 25.5 ±0.5 12.7 164 ft 50m HFTW13641
38.1 (1-1/2) 41.5 ±1 19.1 164 ft 50m HFTW13642
50.8 (2) 51.5 ±1 25.4 82 ft 25m HFTW13643
1.6 (1/16) 1.4 ±0.2 0.8 16.4 ft 5m HFTW13644
2.4 (3/32) 2.4 ±0.2 1.2 16.4 ft 5m HFTW13645
3.2 (1/8) 3.4 ±0.2 1.6 16.4 ft 5m HFTW13646
4.8 (3/16) 4.9 ±0.2 2.4 16.4 ft 5m HFTW13647
6.4 (1/4) 6.5 ±0.2 3.2 16.4 ft 5m HFTW13648
9.5 (3/8) 9.5 ±0.3 4.8 16.4 ft 5m HFTW13649
12.7 (1/2) 12.5 ±0.3 6.4 16.4 ft 5m HFTW13650
19.1 (3/4) 18.5 ±0.4 9.5 16.4 ft 5m HFTW13651
25.4 (1) 25.5 ±0.5 12.7 16.4 ft 5m HFTW13652
38.1 (1-1/2) 41.5 ±1 19.1 16.4 ft 5m HFTW13653
50.8 (2) 51.5 ±1 25.4 16.4 ft 5m HFTW13654
Part Number table