IC61C256AH Document Title 32K x 8 High Speed SRAM Revision History Revision No History Draft Date 0A 0B 0C 0D Initial Draft Revise typo of tHA on page 7 Add SOP package type Revise typo of sop size at page 2,9 March 23,2001 October 18,2001 February 18,2002 April 19,2002 Remark The attached datasheets are provided by ICSI. Integrated Circuit Solution Inc reserve the right to change the specifications and products. ICSI will answer to your questions about device. If you have any questions, please contact the ICSI offices. Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 1 IC61C256AH 32K x 8 HIGH-SPEED CMOS STATIC RAM FEATURES * High-speed access times: 10, 12, 15, 20, 25 ns * Low active power: 400 mW (typical) * Low standby power -- 250 W (typical) CMOS standby -- 55 mW (typical) TTL standby * Fully static operation: no clock or refresh required * TTL compatible interface and outputs * Single 5V power supply DESCRIPTION The ICSI IC61C256AH is very high-speed, low power, 32,768 word by 8-bit static RAMs. They are fabricated using ICSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields access times as fast as 8 ns maximum. When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation is reduced to 50 W (typical) with CMOS input levels. Easy memory expansion is provided by using an active LOW Chip Enable (CE). The active LOW Write Enable (WE) controls both writing and reading of the memory. The IC61C256AH is pin compatible with other 32k x 8 SRAMs and are available in 28-pin 300mil PDIP, 300mil SOJ, and 8*13.4mm TSOP-1 package, 330 mil SOP. FUNCTIONAL BLOCK DIAGRAM A0-A14 DECODER 32K X 8 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VCC GND I/O0-I/O7 CE OE CONTROL CIRCUIT WE ICSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. (c) Copyright 2000, Integrated Circuit Solution Inc. 2 Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 IC61C256AH PIN CONFIGURATION PIN CONFIGURATION 28-Pin DIP and SOJ and SOP A14 1 28 VCC A12 2 27 WE A7 3 26 A13 A6 4 25 A8 A5 5 24 A9 A4 6 23 A11 A3 7 22 OE A2 8 21 A10 A1 9 20 CE A0 10 19 I/O7 I/O0 11 18 I/O6 I/O1 12 17 I/O5 I/O2 13 16 I/O4 GND 14 15 I/O3 PIN DESCRIPTIONS 8x13.4mm TSOP-1 OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3 21 20 19 18 17 16 15 14 13 12 11 10 9 8 22 23 24 25 26 27 28 1 2 3 4 5 6 7 A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 TRUTH TABLE A0-A14 Address Inputs Mode CE Chip Enable Input OE Output Enable Input WE Write Enable Input I/O0-I/O7 Input/Output Not Selected (Power-down) Output Disabled Read Write Vcc Power GND Ground WE CE OE I/O Operation Vcc Current X H X High-Z ISB1, ISB2 H H L L L L H L X High-Z DOUT DIN ICC1,ICC2 ICC1, ICC2 ICC1, ICC2 ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM TBIAS TSTG PD IOUT Parameter Terminal Voltage with Respect to GND Temperature Under Bias Storage Temperature Power Dissipation DC Output Current (LOW) Value -0.5 to +7.0 -55 to +125 -65 to +150 1.5 20 Unit V C C W mA Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 3 IC61C256AH OPERATING RANGE Range Commercial Ambient Temperature 0C to +70C Industrial -40C to +85C Speed -10, -12 -15, -20 -12 VCC 5V, 5% 5V 10% 5V 5% -15, -20, -25 5V 10% Notes: 1. 8 ns is preliminary. DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol Parameter Test Conditions Min. Max. Unit VOH Output HIGH Voltage VCC = Min., IOH = -4.0 mA 2.4 -- V VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA -- 0.4 V 2.2 VCC + 0.5 V -0.5 0.8 V (1) VIH Input HIGH Voltage VIL Input LOW Voltage(2) ILI Input Leakage GND VIN VCC Com. Ind. -5 -10 5 10 A ILO Output Leakage GND VOUT VCC, Outputs Disabled Com. Ind. -5 -10 5 10 A Notes: 1. VIH=VCC +3.0V for pulse width less than 10ns. 2. VIL = -3.0V for pulse width less than 10 ns. POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) -10 -12 -15 -20 Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Unit Com. Ind. -- 145 -- 180 -- 135 -- 170 -- 125 -- 160 -- 120 -- 150 -- 120 -- 140 mA VCC = Max., VIN = VIH or VIL CE VIH, f = 0 Com. Ind. -- 25 -- 30 -- 25 -- 30 -- 25 -- 30 -- 25 -- 30 -- 25 -- 30 mA VCC = Max., CE VCC - 0.2V, VIN VCC - 0.2V, or VIN 0.2V, f = 0 Com. Ind. -- 2 -- 10 -- 2 -- 10 -- 2 -- 10 -- 2 -- 10 -- 2 -- 10 mA Sym. Parameter Test Conditions ICC Vcc Dynamic Operating Supply Current VCC = Max., CE = VIL IOUT = 0 mA, f = fMAX ISB1 TTL Standby Current (TTL Inputs) ISB2 CMOS Standby Current (CMOS Inputs) -25 Notes: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. CAPACITANCE(1,2) Symbol Parameter CIN Input Capacitance COUT Output Capacitance Conditions Max. Unit VIN = 0V 8 pF VOUT = 0V 10 pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25C, f = 1 MHz, Vcc = 5V. 4 Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 IC61C256AH READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) -10 -12 -15 -20 -25 Symbol Parameter Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Unit tRC 10 -- 12 -- 15 -- 20 -- 25 -- ns tAA Address Access Time -- 10 -- 12 -- 15 -- 20 -- 25 ns tOHA Output Hold Time 2 -- 2 -- 2 -- 2 -- 2 -- ns tACE CE Access Time -- 10 -- 12 -- 15 -- 20 -- 25 ns tDOE OE Access Time -- 5 -- 5 -- 7 -- 8 -- 9 ns tLZOE(2)OE to Low-Z Output 0 -- 0 -- 0 -- 0 -- 0 -- ns tHZOE(2)OE to High-Z Output -- 5 -- 6 -- 7 -- 9 -- 10 ns tLZCE CE to Low-Z Output 2 -- 3 -- 3 -- 3 -- 3 -- ns tHZCE CE to High-Z Output -- 5 -- 7 -- 8 -- 9 -- 10 ns 0 -- 0 -- 0 -- 0 -- 0 -- ns -- 10 -- 12 -- 15 -- 18 -- 20 ns Read Cycle Time (2) (2) tPU(3) CE to Power-Up tPD(3) CE to Power-Down Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured 200 mV from steady-state voltage. Not 100% tested. 3. Not 100% tested. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Levels Output Load Unit 0V to 3.0V 3 ns 1.5V See Figures 1 and 2 AC TEST LOADS 480 480 5V 5V OUTPUT OUTPUT 30 pF Including jig and scope Figure 1. Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 255 5 pF Including jig and scope 255 Figure 2. 5 IC61C256AH AC WAVEFORMS READ CYCLE NO. 1(1,2) t RC ADDRESS t AA t OHA t OHA DOUT DATA VALID PREVIOUS DATA VALID READ CYCLE NO. 2(1,3) t RC ADDRESS t AA t OHA OE t HZOE t DOE t LZOE CE t ACE t HZCE t LZCE DOUT HIGH-Z DATA VALID Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE = VIL. 3. Address is valid prior to or coincident with CE LOW transitions. 6 Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 IC61C256AH WRITE CYCLE SWITCHING CHARACTERISTICS(1,2) (Over Operating Range) -10 -12 -15 -20 -25 Parameter Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Unit tWC Write Cycle Time 10 -- 12 -- 15 -- 20 -- 25 -- ns tSCE CE to Write End 9 -- 10 -- 10 -- 13 -- 15 -- ns tAW Address Setup Time to Write End 9 -- 10 -- 12 -- 15 -- 20 -- ns tHA Address Hold from Write End 0 -- 0 -- 0 -- 0 -- 0 -- ns Address Setup Time 0 -- 0 -- 0 -- 0 -- 0 -- ns tPWE WE Pulse Width 8 -- 8 -- 10 -- 13 -- 15 -- ns tSD Data Setup to Write End 7 -- 7 -- 9 -- 10 -- 12 -- ns tHD Data Hold from Write End 0 -- 0 -- 0 -- 0 -- 0 -- ns tHZWE(2) WE LOW to High-Z Output -- 6 -- 6 -- 7 -- 8 -- 10 ns WE HIGH to Low-Z Output 0 -- 0 -- 0 -- 0 -- 0 -- ns Symbol tSA (4) tLZWE Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and output loading specified in Figure 1a. 2. Tested with the load in Figure 1b. Transition is measured 500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 4. Tested with OE HIGH. AC WAVEFORMS WRITE CYCLE NO. 1 (WE Controlled) (1,2 ) t WC VALID ADDRESS ADDRESS t SA t SCE t HA CE t AW t PWE1 t PWE2 WE t HZWE DOUT DATA UNDEFINED t LZWE HIGH-Z t SD DIN Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 t HD DATAIN VALID 7 IC61C256AH WRITE CYCLE NO. 2 (CE Controlled) (1,2) t WC ADDRESS VALID ADDRESS t HA OE CE LOW t AW t PWE1 WE t SA DOUT t HZWE DATA UNDEFINED t LZWE HIGH-Z t SD DIN t HD DATAIN VALID Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 2. I/O will assume the High-Z state if OE VIH. 8 Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 IC61C256AH ORDERING INFORMATION: IC61C256AH Commercial Range: 0C to +70C ORDERING INFORMATION: IC61C256AH Industrial Range: -40C to +85C Speed (ns) Speed (ns) Order Part No. Package 10 10 10 10 IC61C256AH-10N IC61C256AH-10J IC61C256AH-10T IC61C256AH-10U 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP 12 12 12 12 IC61C256AH-12N IC61C256AH-12J IC61C256AH-12T IC61C256AH-12U 15 15 15 15 20 20 20 20 Order Part No. Package 12 12 12 12 IC61C256AH-12NI IC61C256AH-12JI IC61C256AH-12TI IC61C256AH-12UI 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP 15 15 15 15 IC61C256AH-15NI IC61C256AH-15JI IC61C256AH-15TI IC61C256AH-15UI 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP IC61C256AH-15N IC61C256AH-15J IC61C256AH-15T IC61C256AH-15U 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP 20 20 20 20 IC61C256AH-20NI IC61C256AH-20JI IC61C256AH-20TI IC61C256AH-20UI 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP IC61C256AH-20N IC61C256AH-20J IC61C256AH-20T IC61C256AH-20U 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP 25 25 25 25 IC61C256AH-25NI IC61C256AH-25JI IC61C256AH-25TI IC61C256AH-25UI 300mil DIP 300mil SOJ 8*13.4mm TSOP-1 330mil SOP Integrated Circuit Solution Inc. HEADQUARTER: NO.2, TECHNOLOGY RD. V, SCIENCE-BASED INDUSTRIAL PARK, HSIN-CHU, TAIWAN, R.O.C. TEL: 886-3-5780333 Fax: 886-3-5783000 BRANCH OFFICE: 7F, NO. 106, SEC. 1, HSIN-TAI 5TH ROAD, HSICHIH TAIPEI COUNTY, TAIWAN, R.O.C. TEL: 886-2-26962140 FAX: 886-2-26962252 http://www.icsi.com.tw Integrated Circuit Solution Inc. AHSR010-0D 4/19/2002 9