LLC210D3L24-003 - Silicon Storage Technology (SST)

OUTPUT VALUES

Output Voltage3 (Vout): lout = 1A

Vs = 4.5—15.4VDC

Output High Vout = Vs - 1.5V max

Output Low Vout = 0V + 0.5V max

Output Voltage (Vout): lout = 1A

Vs = 8—30VDC

Output High Vout = Vs - 1.8V max

Output Low Vout = 0V + 0.7V max

Other sensor options available on request, email:

technical@sstsensing.com

Need help? Ask the expert

Tel: + 44 (0)1236 459 020

and ask for “Technical”

BENEFITS

 High power

 Industrial supply voltage

 Direct load drive design

TECHNICAL SPECIFICATIONS

Supply voltage (Vs) 4.5VDC to 15.4VDC

or 8VDC to 30VDC

Supply current (ls) 2.5mA max. (Vs = 15.4VDC)

or 7.5mA max. (Vs = 30VDC)

Output sink and source

current (lout) 1A

Operating temperatures Standard: -25°C to +80°C

Extended: -40°C to +125°C

Storage temperatures Standard: -30°C to +85°C

Extended: -40°C to +125°C

Housing material1, 2 Polysulfone or Trogamid®

Sensor termination 20AWG, 250mm PTFE

wires, 8mm tinned

FEATURES

 Liquid level switches that can detect almost any liquid type;

oil or water based

 Choice of material; Polysulfone (standard) or Trogamid®

 Choice of threads

DATA SHEET

Liquid Level Switches

Optomax Industrial Series

1) Above +85°C, Trogamid is suitable for water based liquids. Oil based liquids can cause deformation of the sensing tip

and must be tested for compatibility.

2) Before use check that the fluid in which you wish to use these devices is compatible either with Polysulfone or

Trogamid®.

3) Voltages applicable to output value stated.

NOTES

Housing/

Mounting

Output Type / Logic Supply

Voltage

Output

Current

Temp

1) Hex nut and O-ring sold separately; email: technical@sstsensing.com for details.

2) NPT version can be sealed with PTFE tape.

3) When correctly sealed.

NOTES

OUTLINE DRAWING

All dimensions shown in mm. Tolerances = ±1mm.

HOUSING SPECIFICATIONS

ELECTRICAL INTERFACE

Wire Designation

Red Vs

Green Output

Blue 0V

LLx2x0 Series

LLx6x0 Series

LLx7x0 Series

Housing Series

2x0 6x0 7x0

Thread M12x1x8g

with hex nut1

1/2” SAE with

O-ring1 1/4” NPT2

Pressure3 7 bar /101 psi maximum

Tightening

Torque 1.5 Nm / 13.26 in-lbs maximum

CIRCUIT DIAGRAMS

In order to suit any application, these sensors have been designed with various output circuit configurations. They are identified by

the 3-digit code at the end of the part number as shown in Order Information.

CAUTION: Take care when connecting loads.

The minimum load impedance should not exceed Vs/max output current.

Note: Shorting the output to Vs or 0V will result in irreparable damage to the sensor.

General Note: SST Sensing Ltd. reserves the right to make changes to product specifications without notice or liability.

All information is subject to SST Sensing Ltd.'s own data and considered accurate at time of going to print.

5 H AGMI LL CRES CE N T, S HA WHEAD IND US TR I AL E S TA TE , COATB R IDGE, U K M L5 4 NS

ww w .s st s e ns i ng . co m | e: s a l es @s s ts e n si n g. co m | t : + 44 ( 0 )12 3 6 45902 0 | f: + 4 4 (0 ) 123 6 459 02 6

CAUTION

Do not exceed maximum ratings and ensure sensor(s) are operated in

accordance with their requirements.

Carefully follow all wiring instructions. Incorrect wiring can cause

permanent damage to the device.

SST Sensing Ltd recommend using alcohol based cleaning agents.

Do NOT use chlorinated solvents such as trichloroethane as these are

likely to attack the sensor material.

Failure to comply with these instructions may result in product

damage.

INFORMATION

As customer applications are outside of SST Sensing Ltd.’s control, the

information provided is given without legal responsibility. Customers

should test under their own conditions to ensure that the equipment is

suitable for their intended application. Before use, check that the fluid in

which you wish to use these devices is compatible with Polysulfone or

Trogamid®.

For technical assistance or advice, please email:

technical@sstsensing.com

DS-0034 REV 13

ORDER INFORMATION

Generate your specific part number using the convention shown below. Use only those letters and numbers that correspond to the

sensor and output options you require — omit those you do not.

Housing

Material

Housing

Type

Operating

Temp.

Output

Logic

Supply

Voltage

Output

Type

Polysulfone

2x0 series

M12x1

-25 °C

to +80°C

Output

Low in air

8-30VDC

001

N-Type

with flyback

Trogamid®

6x0 series

1/2” SAE

-40 °C

to +125°C

Blank

Output

High in air

Blank

4.5-15.4VDC

002

N-Type with

10kΩ pull-up

7x0 series

1/4” NPT

003

N-Type

004

P-Type

005

N&P

Push Pull

L L X X X 0 D 3 X X - X X X X