ispLever CORE TM 1GbE PCS IP Core User's Guide October 2005 ipug28_02.0 Lattice Semiconductor 1GbE PCS IP Core User's Guide Introduction The 1GbE PCS Intellectual Property (IP) Core targets the programmable array section of the ORCA(R) ORT42G5 device and provides the PCS (Physical Coding Sublayer) function. PCS (Physical Coding Sublayer) and PMA (Physical Media Attachment) are sublayers of the physical layer implementation of IEEE 802.3 standards. The PCS provides a uniform interface to the MAC sublayer through GMII (Gigabit Media Independent Interface) for all 1000Mb/s PHY implementations. The ORT42G5 device is built on the Series 4 re-configurable embedded System-on-a-Chip (SoC) architecture and is made up of SERDES transceivers containing four channels, each operating at up to 3.7Gbits/s, with a full-duplex synchronous interface with built-in RX Clock and Data Recovery (CDR), and transmitter pre-emphasis, for highspeed data transmission. This user's guide explains the functionality of the 1GbE PCS core and how to achieve the maximum level of performance. The 1GbE PCS core comes with the documentation and the files listed below: * Data sheet * Lattice gate level netlist * Simulation models and test benches available for free evaluation * Core instantiation template Features * Complete 1Gb Ethernet Physical Coding Sublayer solution based on the ORCA ORT42G5 device * IP targeted to the ORT42G5 programmable array section implements functionality conforming to IEEE 803.22002 - Encoding/decoding of GMII data octets - Optional Auto-negotiation function with management registers and interface - 10Gbps aggregate throughput * Ethernet functionality supported by the embedded section of the ORT42G5 - Supports 8b/10b encoding/decoding - Serialization/deserialization of code groups for transmit/receive - Clock recovery from encoded data stream 2 Lattice Semiconductor 1GbE PCS IP Core User's Guide Figure 1. 1GbE PCS Solution ORT42G5 Device Embedded ASB Section Programmable Array Section ort42g5_inf pcs_1g_core PLL PLL tx_sm tx_sync 1G Line SERDES 8b/10b Systembus of ORT42G5 (ASB) tx/rx clocks umi Optional autoneg Optional Management Interface MDIO or MAC interface rx_sm Optional gmii_mac_inf GMII or MAC Interface rx_sync_sm rx_sync_sm rx_sync_cc 125MHz Note: Optional interfaces are not needed if an Ethernet MAC Interfafce is present on-chip Functional Description The major blocks in the 1GbE PCS core are shown in Figure 1. Descriptions of these blocks follow. Transmit Section This section implements the Transmit State Machine which is specified by Figures 36-5 and 36-6 in Clause 36 of the IEEE 802.3-2002 Standard. The PCS Transmit process continuously generates code-groups based upon the TXD <7:0>, TX_EN and TX_ER signals on the GMII, sending them immediately to the Line Interface. The PCS Transmit process monitors the Autonegotiation process transmit flag to determine whether to transmit data or reconfigure the link. Receive Section Receive Synchronization State Machine This module implements the synchronization state machine which is specified by the Figure 36-9 of the IEEE 802.3-2002 Standard. The Synchronization process is responsible for determining whether the underlying receive channel is ready for operation. The process continuously accepts code-groups from the Line Interface and scans them to detect the acquisition and maintenance of code group synchronization. This state machine also sets the sync_status flag which is monitored by the receive state machine. Receive State Machine This module implements the receive state machine, which is specified by Figures 36-7a and 36-7b in Clause 36 of the IEEE 802.3-2002 Standard. The PCS Receive process continuously accepts and monitors code-groups from the Line Interface and generates RXD <7:0>, RX_DV and RX_ER on the GMII, and the internal receiving flag used by the Carrier Sense and Transmit processes. Auto-negotiation This module implements the Auto-negotiation state machine, which is specified by the Figure 37-6 in Clause 37 of the IEEE 802.3-2002 Standard. 3 Lattice Semiconductor 1GbE PCS IP Core User's Guide The Auto-negotiation function that allows a device (local device) to advertise modes of operation it possesses to a device at the remote end of a link segment (link partner) and to detect corresponding operational modes that the link partner may be advertising. The Auto-negotiation function exchanges information between two devices that share a link segment and automatically configures both devices to take maximum advantage of their abilities. Management Interface The MDIO Management Interface is implemented based on specifications in Clause 22 of the IEEE 802.3-2002 standard. The management interface is used to connect a management entity and a managed PHY for the purposes of controlling the PHY and gathering status from the PHY. The management interface consists of a pair of signals that physically transport the management information across the GMII, a frame format and a protocol specification for exchanging management frames, and a register set that can be read and written using these frames. GMII Interface This module, depending on the configuration, provides a GMII Interface or a connection to an on-chip MAC. ORT42G5 Interface This section provides the following functions: * A bridging function between the 8-bit PCS core and the 32-bit Application Specific Block (ASB). The data rate translation cross the two clock domains is achieved using asynchronous FIFOs. * Clock compensation to a tolerance of +/- 100 ppm between the recovered clock and IP system clock. This is done by insertion or deletion of idle characters. * Logic to program the control registers inside the ASB through the system bus User Master Interface. Design Parameters Table 1. Parameter Descriptions Description Parameter GMII_INF If this parameter is set to "yes", a GMII interface will be provided through the FPGA I/Os to an external device. If this parameter is set to "no", an internal interface will be provided to a MAC on the same chip. AUTO_NEG If this parameter is set to "yes", the Auto-negotiation module and Management registers will be enabled. If this parameter is set to "no", the Autonegotiation module and Management registers will be disabled. MDIO_INF The optional MDIO Interface is only available if the Auto-negotiation parameter is set to "yes". If the MDIO parameter is set to "yes", an MDIO interface will be provided through the FPGA I/Os to an external device. 4 Lattice Semiconductor 1GbE PCS IP Core User's Guide Register Descriptions These registers are accessed through the Management Interface (SMI). They are only present if Auto-negotiation and Management Interface options are selected. The registers are based on the register definition in the Section 22 of IEEE 802.3-2002. Table 2. Top Level Register Addresses Register Address Register Name Control Register 0x0 Status Register 0x1 PHY Identifier Register 0x2 PHY Identifier Register 0x3 Auto-negotiation Advertisement Register 0x4 Auto-negotiation Link Partner Ability Register 0x5 Auto-negotiation Expansion Register 0x6 Extended Status Register 0xf Table 3. Register Map for 1GbE PCS Core Name: Control Register Address: 0x0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 RST LP SS0 ANE PD IS RAN DUP COL SS1 Default value: 0x0140 D5 D4 D3 Mode: Read/Write Description: RST 1 = Reset; 0 = Normal operation. Self clearing LP Enables Loopback mode SS0, SS1 Speed Selection set to "01" - indicates 1000 Mb/s. Read only ANE Auto-negotiation Enable RAN Restart Auto-negotiation. Self clearing PD Unsupported functions. Set to Zero. Read only IS Unsupported functions. Set to Zero. Read only COL Unsupported functions. Set to Zero. Read only DUP Duplex mode. Set to One - only Full Duplex supported. Read only. 5 D2 RESERVED D1 D0 Lattice Semiconductor 1GbE PCS IP Core User's Guide Table 3. Register Map for 1GbE PCS Core (Continued) Address: 0x1 D15 D14 Name: Status Register D13 D12 D11 D10 D9 RESERVED D8 D7 D6 D5 D4 D3 D2 D1 D0 ES R PS ANC RF ANA LS JD EC D3 D2 D1 D0 D1 D0 D1 D0 Default value: 0x0109 Mode: Read Only Description: ES Extended Status Information in Register 15. Bit set to One R Reserved. Bit set to zero PS Preamble Suppression. Not supported. Bit set to zero RF Remote Fault ANA Auto-negotiation Ability. Bit set to One LS Link Status JD Jabber Detect. Not supported. Bit set to zero EC Extended Register capability ANC Auto-negotiation Complete Name: PHY Identifier Register Address: 0x2 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 PHY2 Default value: 0x2222 Mode: Read Only Description: PHY2 Combined with Register 3 it forms a 32-bit value which serves as an identifier. Address: 0x3 Name: PHY Identifier Register D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 PHY3 Default value: 0x3333 Mode: Read Only Description: PHY3 Combined with Register 2 it forms a 32-bit value which serves as an identifier. Address: 0x4 D15 D14 NP R Name: Auto-negotiation Advertisement Register D13 D12 RF D11 D10 RESERVED D9 D8 D7 PAUSE Default value: 0x01 D6 D5 HD FD Mode: Read/Write Description: This register contains the Advertised Ability of the PHY. RESERVED, R Reserved bits are set to zero FD Full Duplex mode supported. Bit set to One HD Half Duplex mode not supported. Bit set to Zero PAUSE Provides Pause capability exchange mechanism RF Remote Fault encoding not supported. Bits set to zero NP Next Page Function. Not supported. Bit set to zero. 6 D4 D3 D2 RESERVED Lattice Semiconductor 1GbE PCS IP Core User's Guide Table 3. Register Map for 1GbE PCS Core (Continued) Address: 0x5 D15 D14 Name: Auto-negotiation Link Partner Ability Register D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 LP_ADV_ABILITY Default value: 0x0000 Mode: Read Only Description: LP_ADV_ABILITY This register contains the Advertised Ability of the Link Partner's PHY. Address: 0x6 Name: Auto-negotiation Expansion Register D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 RESERVED Default value: 0x0000 D2 D1 D0 NP AN R D2 D1 D0 Mode: Read Only Description: RESERVED, R Reserved bits are set to zero NP Next Page Able (In this core the value is "0") AN New Page Received Address: 0xF Name: Extended Status Register D15 D14 D13 D12 D11 D10 D9 D8 FD D7 D6 D5 RESERVED Default value: 0x8000 Mode: Read Only Description: RESERVED Reserved bits are set to zero FD 1000BaseX Full Duplex supported (set to "1" in this core) 7 D4 D3 Lattice Semiconductor 1GbE PCS IP Core User's Guide Signal Descriptions Table 4. Signal Definitions for 1GbE PCS Solution I/O Signal Name Direction Description Clocks and Resets RX_CLK_125 Input Receive Clock (125MHz) TX_CLK_125 Input Transmit Clock (125MHz) RST_N Input Active Low Reset USR_CLK Input Clock for the User Master Interface GMII/MAC Interface RX_DV Output Receive Data Valid RX_D [7:0] Output Receive Data Bus RX_ER Output Receive TX_ER Input Transmit Error Indicator TX_D [7:0] Input Transmit Data Bus TX_DV Input Transmit Data Valid MDC Input MDIO clock MDIO Input/Output MDIO Signals MDIO bi-directional data 1 Line Interface REFCLKN_A Input CML reference clock input - SERDES Quad A REFCLKP_A Input CML reference clock input - SERDES Quad A HDINN_AC Input High-speed CML receive data input - SERDES Quad A, Channel C HDINP_AC Input High-speed CML receive data input - SERDES Quad A, Channel C HDOUTN_AC Output High-speed CML receive data output - SERDES Quad A, Channel C HDOUTP_AC Output High-speed CML receive data output - SERDES Quad A, Channel C Auto-negotiation Signals (if MDIO is not implemented) MR_ADV_ABILITY[15:0] Input Advertisement Register MR_AN_ENABLE Input Enable Auto-negotiation MR_RESTART_EN Input Restart Auto-negotiation MR_AN_COMPLETE Output Auto-negotiation Complete MR_LP_ADV_ABILITY[15:0] Output Link Partner Ability Register MR_PAGE_RX Output Page Received LINK_STATUS Output Link Status Control Signals (if MDIO is not implemented) MR_MAIN_RESET Input Core Reset MR_LOOPBACK Input Enable Loopback 1. The signals listed here are required for the Embedded SPI-4 interface Quad A, Channel C. Please refer to the ORT42G5 Data Sheet for additional information on configuring the SPI-4 interface for specific applications. 8 Lattice Semiconductor 1GbE PCS IP Core User's Guide Table 5. Signal Definitions for 1GbE PCS Solution - FPGA/Embedded ASB Interface (Internal to ORT42G5 Device)1 Signal Name FPGA Direction Description Receive Interface Signals RSYSCLK_A2 Output Low-speed receive FIFO clock for Channel AC RCK78A Input Receive low-speed clock to FPGA - SERDES Quad A MRWDAC[39] Input Code violation for Receive Data Byte 3 Channel AC MRWDAC[38] Input K_CTRL for Receive Data Byte 3 Channel AC MRWDAC[37:30] Input Receive Data Byte 3 Channel AC MRWDAC[29] Input Code violation for Receive Data Byte 2 Channel AC MRWDAC[28] Input K_CTRL for Receive Data Byte 2 Channel AC MRWDAC[27:20] Input Receive Data Byte 2 Channel AC MRWDAC[19] Input Code violation for Receive Data Byte 1 Channel AC MRWDAC[18] Input K_CTRL for Receive Data Byte 1 Channel AC MRWDAC[17:10] Input Receive Data Byte 1 Channel AC MRWDAC[9] Input Code violation for Receive Data Byte 0 Channel AC MRWDAC[8] Input K_CTRL for Receive Data Byte 0 Channel AC MRWDAC[7:0] Input Receive Data Byte 0 Channel AC Transmit Interface Signals TSYSCLK_AC TCK78A Output Input Transmit Low Speed Clock Channel AC Transmit Low Speed Clock to FPGA - SERDES Quad A TWDAC[31:0] Output Transmit Data Channel AC TCOMMAAC[3:0] Output Transmit Comma Character Channel AC TBIT9AC[3:0] Output Transmit Force Negative Disparity Channel AC 1. The signals listed here are required for the Embedded SPI-4 interface Quad A, Channel C. Please refer to the ORT42G5 Data Sheet for additional information on configuring the SPI-4 interface for specific applications. 9 Lattice Semiconductor 1GbE PCS IP Core User's Guide 1GbE PCS Core Design Flow The 1GbE PCS IP Core can be implemented using various methods. The scope of this document covers only the push-button Graphical User Interface (GUI) flow. Figure 2 illustrates the software flow model used when evaluating with the 1GbE PCS. Figure 2. Lattice IP Core Evaluation Flow Start Install and launch ispLEVER software Obtain desired IP package (download Core Evaluation package or purchase IP package) Protected Simulation Model Install IP package IP Core Netlist Perform functional simulation with the provided core model Synthesize top-level design with the IP black box declaration Place and route the design Run static timing analysis Done Functional Simulation Simulation script files are provided in the "eval" directory for RTL simulation. These scripts rely on the sysbus and ORT42G5 models already installed with the ispLEVER(R) software which includes the ORT42G5 device. If these models are not installed, they should be installed before proceeding with this IP Core evaluation. The script file <user_compile.do > will compile all of the user code in the evaluation. The user code for this IP core is the top level chip module. The script file <user_vsim.do> will need to be modified by the user to point to the sysbus and ORT42G5 simulation models (The ORT42G5 uses the ort82g5_work simulation model). Once modified this script will load the full chip and testbench. The script file <user_wave.do> will add all of the appropriate wave- 10 Lattice Semiconductor 1GbE PCS IP Core User's Guide forms for the user. These scripts care located in the 1gbe_pcs_o4_1_001\orca4\ver1.0\eval\simulation\scripts. NOTE: The procedure described here is applicable ONLY when using ModelSim for simulation. Simulation Procedures 1. Launch ModelSim 2. Using the main GUI, change the directory location Select: File -> Change Directory -> 1gbe_pcs_o4_1_001\orca4\ver1.0\eval\simulation 3. Execute <user_compile.do> to compile the full chip design and testbench files. Select: Macro -> Execute Macro -> scripts\<user_compile.do> For ModelSim 5.6a or above: Select: Tools -> Execute Macro -> scripts\<user_compile.do> 4. Modify the script <user_vsim.do> to point to the sysbus_work and ort82g5_work simulation model. These models are provided in the ispLEVER installation and ORT42G5. 5. Execute <user_vsim.do> to load the full chip design and testbench Select: Macro -> Execute Macro -> scripts\<user_vsim.do> For ModelSim 5.6a or above: Select: Tools -> Execute Macro -> scripts\<user_vsim.do> 6. Execute <user_wave.do> to load the appropriate waveforms for the simulation Select: Macro -> Execute Macro -> scripts\<user_wave.do> For ModelSim 5.6a or above: Select: Tools -> Execute Macro -> scripts\<user_wave.do> 7. Run the simulation. Select: Simulate -> Run -> Run-all Core Implementation Running Synthesis Using Synplicity's Synplify The step-by-step procedure provided below describes how to run synthesis using Synplify outside the ispLEVER Project Navigator. 1. Change directory to 1gbe_pcs_o4_1_001\orca4\ver1.0\eval\synthesis\synplicity 2. Launch the Synplify synthesis tool 3. Select: Run -> Run TCL Script... -> pcs_1g_top.tcl 4. Within the provided project file the speed grade, implementation and device are preselected. 5. A default EDIF is also provided by the project file. This top-level EDIF netlist will be used during Place and Route. 6. Within the supplied synthesis scripts the necessary options have been supplied for a complete synthesis pass. 7. Select Run 8. The EDIF file (.edn) will be located in the ver1.0 directory. 11 Lattice Semiconductor 1GbE PCS IP Core User's Guide Running Synthesis Using LeonardoSpectrum The step-by-step procedure provided below describes how to run synthesis using LeondardoSpectrum outside the ispLEVER Project Navigator. 1. Change directory to: 1gbe_pcs_o4_1_001\orca4\ver1.0\eval\synthesis\exemplar 2. Launch the LeonardoSpectrum synthesis tool 3. Start a new project by opening <pcs_1g_top.tcl> Select: File -> Run Script -> pcs_1g_top.tcl 4. The script file contains the necessary parameters to target an ORCA 4 device. 5. The EDIF and generated preference file will be located in the same directory. Running Place and Route (PAR) for ORCA devices in ispLEVER The step-by-step procedure provided below describes how to perform Place and Route in ispLEVER for an ORCA device. The core is required to internally interface with the customer application logic. The Place and Route tool requires a parameter constraint file for the particular GbE PCS IP core in order to correctly create an .NCD file. 1. Launch the Lattice Project Navigator tool. 2. Start a new project: File -> New Project 3. Browse to the directory of the desired location of the project. The generated files will be placed in this directory. 4. Enter the project name and then select EDIF as the project type. 5. Change the device type to an ORT42G5 with a -2 speed grade and BM484 package. 6. Copy the following files to the Place and Route working directory: a) ..\eval\ngo\1gbe_pcs_o4_1_001.ngo b) ..\eval\prf\<synthesis tool>\pcs_1g_top.prf c) The top-level EDIF netlist generated from running synthesis 7. Import the EDIF netlist into the project: Source -> Import... 8. Import the preference file into the project: Source -> Import Constraint File... 9. In the ispLEVER Project Navigator, highlight Place & Route Design, with a right mouse click select Properties. Set the following properties: - Placement Iterations: <5 > - Routing Passes: <15> All other options remain at their default values. 10. Select the Place & Route Trace Report in the project navigator to execute Place and Route and generate a timing report for ORCA. 12 Lattice Semiconductor 1GbE PCS IP Core User's Guide Reference Information The 1GbE PCS IP core solution is compliant with the standard IEEE 803.2-2002. A complete description of this standard is given in the specification document. Additional information on implementing this solution is contained in the following documents: * ORCA ORT42G5 FPSC Data Sheet * ORCA Series 4 FPGAs Data Sheet * Lattice technical note number TN1017, ORCA Series4 MPI/System Bus These documents are available on the Lattice web site at www.latticesemi.com. Technical Support Assistance Hotline: 1-800-LATTICE (North America) +1-503-268-8001 (Outside North America) e-mail: techsupport@latticesemi.com Internet: www.latticesemi.com 13 Lattice Semiconductor 1GbE PCS IP Core User's Guide Appendix for ORCA Series 4 ORT42G5 FPSC Table 6. Available Configuration Configuration Number 001 Configuration Features * GMII interface through FPGA I/Os. * No auto-negotiation and Management registers. * No MDIO interface. Table 7. Performance and Utilization1 Configuration PFUs Block RAM PLL LUTs Registers fMAX 1gbe_pcs_o4_1_001 157 4 2 622 605 125 MHz tx_clk rx_clk 1. Performance and utilization characteristics are generated using an ORT42G5-2BM484C in Lattice's ispLEVER 4.0 software. When using this IP core in a different density, package, speed, or grade within the ORT42G5 family, performance may vary. Supplied Netlist Configurations The Ordering Part Number (OPN) for all configurations of this core is 1GBE-PCS-O4-N1. You can use the IPexpressTM software tool to help generate new configurations of this IP core. IPexpress is the Lattice IP configuration utility, and is included as a standard feature of the ispLEVER design tools. Details regarding the usage of IPexpress can be found in the IPexpress and ispLEVER help system. For more information on the ispLEVER design tools, visit the Lattice web site at: www.latticesemi.com/software. 14 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Lattice: 1GBE-PCS-O4-N1