CLL032-1212A5-503M1A2 - Citizen

and　　　　　　　　 are trademarks or registered trademarks of CITIZEN HOLDINGS CO., LTD. JAPAN.

DATA SHEET

CLL032-1212A5-503M1A2

is a trademark or a registered trademark of CITIZEN ELECTRONICS CO., LTD. JAPAN.

Ref.CE-P2307 03/13 R1(1013)

1. Scope of Application

This data sheet is applied to the LED package, model CLL032-1212A5-503M1A2.

2. Part code

[1] Part Code

[2] Dies in series quantity

[3] Dies in parallel quantity

[4] Correlated color temperature

5000K

[5] Chromaticity range

[6] CRI

Ra 80min.

Features

- External Dimensions:

19.0 x 19.0 x 1.4

- Internal Structure:

Aluminum Base Chip on Board

- Connection to Heat Sink:

By M3 screw (Recommended)

-Luminous Flux: 3205 lm @ 720 mA

-CCT:

5000K (ANSI C78.377 Compliant, in 3-Step MacAdam Ellipse)

-CRI: Ra 80min.

-Thermal Resistance: 0.8 C/W

- RoHS Compliant

1/11

DATA SHEET

CLL 032 - 12 12 A5 - 50 3 M1 A2

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL032-1212A5-503M1A2

[1]

[2]

[3]

[4]

[5]

[6]

Ref.CE-P2307 03/13 R1(1013)

3. Outline drawing - Marking

Marking 1 : Serial No.

Marking 2 :

A 12 12 50 M1

CRI

CCT

Dies in parallel quantity

Dies in series quantity

CLL032

4. Performance

(1) Absolute Maximum Rating

*1 Input power and forward current are the values when the LED is used within the range of

the derating curve in this data sheet.

*2 Refer to 3. Outline drawing for Tc measurement point

*3 D.C. Current : Tj = Tc + Rj-c X Pi

Forward Current

Mnimum current

min

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL032-1212A5-503M1A2

DATA SHEET

140

Case Temperature Tc 100

Reverse Current

2/11

Junction Temperature

Storage Temperature

-40 ~ +100

Operating Temperature

-30 ~ +85

1440

Symbol

Rating Value

Unit

Parameter

64.4 W

Input Power Pi

Unit : mm

Tolerances unless otherwise specified : +/-0.3

Anode

Cathode

Marking 2

Marking 1

(Tc Measurement Point)

Resin area (including white resin)

Anode Cathode

×12

Protection device

Ref.CE-P2307 03/13 R1(1013)

(2) Electro-optical Characteristics

Tc=25C

Chromaticity coordinates ( Condition : IF=720mA, Tc = 25C

）

Note: The tolerance of measurement at our tester is VF+/-3% , Φv+/-10% , Chromaticity(x,y)+/-0.005 and Ra+/-1.

CITILED

Name CLL032-1212A5-503M1A2

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

C/W

Thermal Resistance

Rj-c

Junction-Case

0.8

- - -80CRI

Φv

IF=720mA

Luminous Flux 3205

IF=720mA -lm

2725

Min. Typ.

39.9 V

Max. Unit

DATA SHEET 3/11

Forward Voltage

Symbol

IF=720mA

33.6

F36.2

Parameter Condition

Reference

(ANSI C78.377)

x y x y

0.3447 0.3553 Center 0.3447 0.3553

a 0.3551 0.3760

a 0.00822 b 0.3376 0.3616

b 0.00354 c 0.3366 0.3369

θ° 59.62 d 0.3515 0.3487

*Color region stay within MacAdam "3-step" ellipse from the chromaticity center.

*The chromaticity center refers to ANSI C78.377:2008.

Please refer to ANSI C78.377 for the chromaticity center.

*θ is the angle between the major axis of the ellipse and the x-axis,

and a and b are the major and minor semi-axes of an ellipse. (Ref. IEC 60081:1997 AnnexD)

Center

5000K

Oval parameter

x-y chart-CIE1931

0.33

0.34

0.35

0.36

0.37

0.38

0.32 0.33 0.34 0.35 0.36 0.37

Color region

(ANSI)

B.B. Locus

4800K

5400K 5000K 4600K

5200K

Ref.CE-P2307 03/13 R1(1013)

5. Characteristics

Forward Current vs. Forward Voltage

Forward Current vs. Relative Luminous Flux

Tc=25C Tc=25C

Forward Current vs. Chromaticity Coordinate

Case Temperature vs. Chromaticity Coordinate

Tc=25C IF=720mA

4/11

DATA SHEET

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL032-1212A5-503M1A2

30.0

31.0

32.0

33.0

34.0

35.0

36.0

37.0

38.0

39.0

40.0

0 300 600 900 1200 1500

IF [mA]

[V]

20%

40%

60%

80%

100%

120%

140%

160%

180%

200%

0 300 600 900 1200 1500

IF [mA]

Relative Luminous Flux [a.u.]

-0.020

-0.015

-0.010

-0.005

0.000

0.005

0.010

0.015

0.020

0 300 600 900 1200 1500

IF [mA]

△

Δｘ

Δｙ

-0.020

-0.015

-0.010

-0.005

0.000

0.005

0.010

0.015

0.020

0 25 50 75 100

Tc [C]

△

Δｘ

Δｙ

Ref.CE-P2307 03/13 R1(1013)

Case Temperature vs. Forward Voltage

Case Temperature vs. Relative Luminous Flux

IF=720mA IF=720mA

Case Temperature vs. Allowable Forward Current

Spectrum

Tc=25C, IF =720 mA

Directive Characteristic

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET 5/11

Symbol

CITILED

Name CLL032-1212A5-503M1A2

33.0

34.0

35.0

36.0

37.0

38.0

39.0

0 25 50 75 100

Tc [C]

[V]

20%

40%

60%

80%

100%

120%

0 25 50 75 100

Tc [C]

Relative Luminous Flux [a.u.]

200

400

600

800

1000

1200

1400

1600

0 25 50 75 100 125

Tc [C]

[mA]

20%

40%

60%

80%

100%

120%

350 450 550 650 750 850

λ [nm]

Relative Emission Intensity [a.u.]

20%

40%

60%

80%

100%

80°

70°

60°

50°

40°30°20°10°

-80°

-70°

-60°

-50°

-20°-30°-40° -10°

90°

-90°

X direction

Y direction

Ref.CE-P2307 03/13 R1(1013)

6. Reliability

（１）

Datails of the tests

(2)Judgement Criteria of Failure for Reliability Test

(Ta=25C)

U defines the upper limit of the specified characteristics. S defines the initial value.

Note : Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be

return to the normal ambient conditions after the completion of each test.

6/11

-40 C × 30 minutes – 100 C × 30 minutes, 100 cycle

Symbol

CITILED

85 C, 85 %RH for 500 hours

IF=720mA

Ta=25C (with Al-fin) × 1000 hours

IF=720mA

Tj=140C (with Al-fin) × 1000 hours

-40 C × 1000 hours

100 C × 1000 hours

Name CLL032-1212A5-503M1A2

IF=720mA

Φv

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET

>U X 1.1

<S X 0.85

IF=720mAForward Voltage

Total Luminous Flux

Symbol

Measuring Condition

Judgement Criteria for Failure

Test Item

Test Condition

Measuring Item

Continuous Operation Test

Low Temperature Storage Test

High Temperature Storage Test

Moisture-proof Test

Thermal Shock Test

Ref.CE-P2307 03/13 R1(1013)

7. Packing Specifications

(1) Packing

An empty tray is placed on top of a 6-tier tray which contain 48 pieces each.

(Smallest packing unit: 288 pieces)

A label with product name, quantity, lot number is placed on the upper empty tray.

Tray (Dimensions: 310 x 210 x 12 mm / Materials: Electrically conductive PS)

Product 48pcs/tray

< Example of indication label > 1. TYPE e.g. CLL032-1212A5-503M1A2

2. P.No. (Cutomer's P/N)

3. Lot No.

- First and second letter: Last digit of the year e.g. 13 : year 2013

- Third letter: Production month e.g. 3 : Mar

Note: October, November and December are designated

- Forth letter: CE's control number e.g. 5035

4. Quantity

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

DATA SHEET 7/11

CITILED

Name CLL032-1212A5-503M1A2

< Packing figure >

CUSTOMER

PASS

CITIZEN ELECTRONICS

TYPE

P. NO

Lot No

Q'ty

: ******-******-*******

: ******

: *******

: ***

---(1)

---(2)

---(3)

---(4)

< Packing figure >< Packing figure >< Packing figure >

Ref.CE-P2307 03/13 R1(1013)

．

Precautions

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL032-1212A5-503M1A2

DATA SHEET 8/11

(1) 1. Handling with care for this product

-Both the light emitting area and white dam over the light emitting area is composed of resin materials.

Please avoid the resin area from being pressed, stressed, rubbed, come into contact with sharp metal nail

(e.g. edge of reflector part) because the function, performance and reliability of this product

are negatively impacted.

-Please be aware that this product should not come into contact with any other parts

while incorporating in your lighting apparatus or your other products.

(2) Countermeasure against static electricity

-Handling of this product needs countermeasures against static electricity

because this is a semiconductor product.

-Please take adequate measures to prevent any static electricity being produced

such as the wearing of a wristband or anti-static gloves when handling this product.

-Every manufacturing facility in regard to the product (plant, equipment, machine, carrier machine

and conveyance unit) should be connected to ground and please avoid the product to be electric-charged.

-ESD sensitivity of this product is over 1000V (HBM, based on JEITA ED-4701/304).

-After assembling the LEDs into your final product(s), it is recommended to check

whether the assembled LEDs are damaged by static electricity (electrical leak phenomenon) or not.

-It is easy to find static damaged LED dies by a light-on test with the minimum current value.

(3) Caution of product assembly

-Regarding this product assembling on the heat sink, it is recommended to use M3 screw.

It might be good for screw tightening on the heat sink to do temporary tightening and final tightening.

In addition, please don’t press with excess stress on the product.

-The condition of the product assembling on the heat sink and the control of screw tightening torque

needs to be optimized according to the specification of the heat sink.

-Roughness, unevenness and burr of surface negatively impact thermal bonding

between the product and heat sink and increase heat thermal resistance between them.

Confidence of thermally and mechanical coupling between the product and heat sink are confirmed

by checking the mounting surface and measuring the case temperature of the product.

-In order to reduce the thermal resistance at assembly, it might be good to use

TIM (Thermal Interface Material) on whole contact surface of the product.

In case of using thermal grease for the TIM, it might be good to apply uniformly

on the contact surface of the product. In case of using thermal sheet for the TIM,

it might be good to make sure that the product is NOT strained by stress

when the screws are tightened for assembly.

Ref.CE-P2307 03/13 R1(1013)

8. Precautions (continued)

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET 9/11

Symbol

CITILED

Name CLL032-1212A5-503M1A2

(4) Thermal Design

-The thermal design to draw heat away from the LED junction is most critical parameter

for an LED illumination system. High operating temperatures at the LED junction adversely affect

the performance of LED’s light output and lifetime. Therefore the LED junction temperature should

not exceed the absolute maximum rating in LED illumination system.

-The LED junction temperature while operation of LED illumination system depends upon

thermal resistance of internal LED package (Rj-c), outer thermal resistances of LED package,

power loss and ambient temperature. Please take both of the thermal design specifications

and ambient temperature conditions into consideration for the setting of driving conditions.

-For more information, please refer to application note "Thermal Management".

(5) Driving Current

-A constant current is recommended as an applying driving current to this product.

In the case of constant voltage driving, please connect current-limiting resistor to each products in series

and control the driving current to keep under the absolute maximum rating forward current value.

-Electrical transient might apply excess voltage, excess current and reverse voltage to the product(s).

They also affect negative impact on the product(s) therefore please make sure that no excess voltage,

excess current and reverse voltage is applied to the product(s)

when the LED driver is turn-on and/or turn-off.

-For more information, please refer to application note "Driving".

(6) Lighting at a minimum current value

-In a case where the minimum current(IF min) is applied to the product,

some of LED dice in the product might look different in their brightness

due to the individual difference of the LED dice, and they are not failed.

(7) Electrical Safety

-This product is designed and produced according to IEC 62031:2008

(IEC 62031:2008 LED modules for general lighting. Safety specification)

-Dielectric voltage withstand test has been conducted on this product to see any failure

after applying voltage between active pads and aluminum section of the product,

and to pass at least 500V.

-Considering conformity assessment for IEC62031:2008, almost all items of the specification

depend upon your final product of LED illumination system.

Therefore, please confirm with your final product for electrical safety of your product.

As well, the products comply with the criteria of IEC62031:2008 as single LED package.

Ref.CE-P2307 03/13 R1(1013)

8. Precautions (continued)

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL032-1212A5-503M1A2

DATA SHEET 10/11

(9) Eye Safety

-The International Electrical Commission (IEC) published in 2006 IEC 62471

”2006 Photobiological safety of lamps and lamp systems ” which includes LEDs within its scope.

When sorting single LEDs according to IEC 62471, almost all white LEDs can be classified

as belonging to either Exempt Group (no hazard) or Risk Group 1 (low risk).

-However, Optical characteristics of LEDs such as radiant flux,

spectrum and light distribution are factors that affect the risk group determination of the LED,

and especially a high-power LED, that emits light containing blue wavelengths,

might have properties equivalent to those of Risk Group 2 (moderate risk).

-Great care should be taken when directly viewing an LED that is driven at high current,

has multiple uses as a module or when focusing the light with optical instruments,

as these actions might greatly increase the hazard to your eyes.

-It is recommended to regard the evaluation of stand-alone LED packages as a reference

and to evaluate your final product.

(10) This product is not designed for usage under the following conditions.

If the product might be used under the following conditions, you shall evaluate its effect

and appropriate them. In places where the product might:

-directly and indirectly get wet due to rain and/or at place with the fear.

-be damage by seawater and/or at place with the fear

-be exposed to corrosive gas (such as Cl2, H2S, NH3, SOx, NOx and so on) and/or at place with the fear.

-be exposed to dust, fluid or oil and/or at place with the fear.

(8) Recommended soldering Condition (This product is not adaptable to reflow process.)

-For manual soldering

Please use lead-free soldering.

Soldering shall be implemented using a soldering bit at a temperature lower than 350C,

and shall be finished within 3.5 seconds for one land.

No external force shall be applied to resin part while soldering is implemented.

Next process of soldering should be carried out after the product has return to ambient temperature.

-For soldering correction

Regarding soldering correction, above conditions shall be applied.

Contacts number of soldering bit should be within twice for each terminal as a correction.

* Citizen Electronics cannot guarantee if usage exceeds these recommended conditions.

Please use it after sufficient verification is carried out on your own risk if absolutely necessary.

Ref.CE-P2307 03/13 R1(1013)

9. Precautions with regard to product use

(1) This document is provided for reference purposes only so that CITIZEN ELECTRONICS'

products are used as intended. CITIZEN ELECTRONICS neither makes warranties or

representations with respect to the accuracy or completeness of the information contained

in this document nor grants any license to any intellectual property rights or any other

rights of CITIZEN ELECTRONICS or any third party with respect to the information

in this document.

(2) All information included in this document such as product data, diagrams, charts,

is current as of the date this document is issued.

Such information, however, is subject to change without any prior notice.

Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document,

please confirm the latest product information with a CITIZEN ELECTRONICS' sales office,

and formal specifications must be exchanged and signed by both parties prior to mass production.

(3) CITIZEN ELECTRONICS has used reasonable care in compiling the information

included in this document,

but CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as

a result of errors or omissions in the information included in this document.

(4) Absent

ａ

written signed agreement, except as provided in the relevant terms and conditions of

sale for product, and to the maximum extent allowable by law, CITIZEN ELECTRONICS

assumes no liability whatsoever, including without limitation, indirect, consequential, special,

or incidental damages or loss, including without limitation, loss of profits, loss of opportunities,

business interruption and loss of data, and disclaims any and all express or implied warranties

and conditions related to sale, use of product, or information, including warranties

or conditions of merchantability, fitness for a particular purpose, accuracy of information,

or no infringement.

(5) Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability,

products can malfunction or fail. Customers are responsible for complying with safety standards

and for providing adequate designs and safeguards to minimize risk and avoid situations

in which a malfunction or failure of a product could cause loss of human life,

bodily injury or damage to property, including data loss or corruption.

In addition, customers are also responsible for determining the appropriateness of

use of any information contained in this document such as application cases not only with

evaluating by their own but also by the entire system.

CITIZEN ELECTRONICS assumes no liability for customers' product design or applications.

(6) Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding

the information contained in this document, or if you have any other inquiries.

CITIZEN Micro HumanTech is a registered trademark of Citizen Holding Co., Japan.

CITILED is a registered trademark of CITIZEN ELECTRONICS CO., LTD. Japan

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET 11/11

Symbol

CITILED

Name CLL032-1212A5-503M1A2

Ref.CE-P2307 03/13 R1(1013)