NXP Semiconductors Technical Data Document Number: MC33978 Rev. 8.0, 7/2018 22 channel multiple switch detection interface with programmable wetting current 33978 34978 MULTIPLE SWITCH DETECTION INTERFACE The 33978 is designed to detect the closing and opening of up to 22 switch contacts. The switch status, either open or closed, is transferred to the microprocessor unit (MCU) through a serial peripheral interface (SPI). This SMARTMOS device also features a 24-to-1 analog multiplexer for reading the input channels as analog inputs. The analog selected input signal is buffered and provided on the AMUX output pin for the MCU to read. Independent programmable wetting currents are available as needed for the application. A battery and temperature monitor are included in the IC and available via the AMUX pin. The 33978 device has two modes of operation, Normal and Low-power mode (LPM). Normal mode allows programming of the device and supplies switch contacts with pull-up or pull-down current as it monitors the change of state on the switches. The LPM provides low quiescent current, which makes the 33978 ideal for automotive and industrial products requiring low sleep-state currents. Features * Fully functional operation 4.5 V VBATP 36 V * Full parametric operation 6.0 V VBATP 28 V * Operating switch input voltage range from -1.0 V to 36 V * Eight programmable inputs (switches to battery or ground) * 14 switch-to-ground inputs * Selectable wetting current (2, 6, 8, 10, 12, 14, 16, or 20 mA) * Interfaces directly to an MCU using 3.3 V / 5.0 V SPI protocol * Selectable wake-up on change of state * Typical standby current IBATP = 30 A and IDDQ = 10 A * Active interrupt (INT_B) on change-of-switch state * Integrated battery and temperature sensing EK SUFFIX (PB-FREE) 98ASA10556D 32-PIN SOICW-EP ES SUFFIX (PB-FREE) 98ASA00656D 32-PIN QFN (WF-TYPE) Applications * Automotive * Heating ventilation and air conditioning (HVAC) * Lighting * Central gateway/in-vehicle networking * Gasoline engine management * Industrial * Programmable logic control (PLC) * Process control, temperature control * Input-output control (I/O Control) * Single board computer * Ethernet switch Notes 1. The IC is functional from 4.5 V < VBATP < 6.0 V, but with degraded parametric values. The parameters may not meet the minimum and maximum specifications when VBATP drops below 6.0 V. VDDQ Battery Power Supply 33978 SG1 Battery SP0 VBATP WAKE_B SP1 SP7 SG0 Power Supply MCU VDDQ INT_B INTB CS_B MISO MOSI SCLK CSB MISO MOSI SCLK AMUX AN0 SG12 SG13 EP GND Figure 1. 33978 simplified application diagram (c) NXP B.V. 2018. Table of Contents 1 2 3 Orderable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Internal block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.2 Pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.2 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.2 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 General IC functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.1 Battery voltage ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.2 Power sequencing conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7 Functional block description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.1 State diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.2 Low-power mode operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.3 Input functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.4 Oscillator and timer control functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 7.5 Temperature monitor and control functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 7.6 WAKE_B control functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 7.7 INT_B functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.8 AMUX functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.9 Serial peripheral interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7.10 SPI control register definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 8.1 Application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 8.2 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 8.3 Abnormal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 9.1 Package mechanical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 10 Reference section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 33978 NXP Semiconductors 2 1 Orderable parts This section describes the part numbers available to be purchased along with their differences. Table 1. Orderable part variations Part number Temperature (TA) Package Notes MC33978EK MC33978AEK (2), (3) -40 C to 125 C MC33978AES SOICW-EP 32 pins (2) QFN (WF-TYPE) 32 pins MC34978EK MC34978AEK MC34978AES (2), (3) -40 C to 105 C SOICW-EP 32 pins (2) QFN (WF-TYPE) 32 pins Notes 2. To order parts in tape and reel, add the R2 suffix to the part number. 3. Refer to errata MC33978ER ER01 for details on current conditions present on the MC33978EK and MC34978EK devices only. 33978 3 NXP Semiconductors 2 Internal block diagram Inputs VBATP SG0 Internal 2.5 V VBATP, VDDQ Internal 2.5 V/5.0 V Power On Reset Bandgap reference Sleep Power VBATP Wetting (2.0 mA to 20 mA) Sustain (2.0 mA) Low Power Mode (1.0 mA) VBATP VDDQ GND EP SG0 Internal 2.5 V To SPI 4.0 V reference SG1 Oscillator and Clock control SG2 VBATP VBATP SG5 Internal 2.5 V Temperature Monitor and Control Wetting (2.0 mA to 20 mA) Sustain (2.0 mA) Low Power Mode (1.0 mA) VDDQ 125 k SG5 Internal 2.5 V To SPI 4.0 V reference WAKE_B WAKE_B control 1/6 Ratio Internal 2.5 V VBATP SGx VDDQ 125 k INT_B Interrupt control Wetting (2.0 mA to 20 mA) Sustain (2.0 mA) Low Power Mode (1.0 mA) Internal 2.5 V SG13 SPI Interface and Control To SPI 4.0 V reference VDDQ 125 k CS_B SCLK VBATP SP0-7 VDDQ Mux control Wetting (2.0 mA to 20 mA) Sustain (2.0 mA) Low Power Mode (1.0 mA) SP0 SP1 MOSI MISO 24 To SPI VDDQ + - AMUX 4.0 V reference Wetting (2.0 mA to 20 mA) Sustain (2.0 mA) Low Power Mode (2.0 mA) SP7 Figure 2. 33978 internal block diagram 33978 NXP Semiconductors 4 3 Pin connections 3.1 Pinout Transparent Top View 29 5 28 6 27 7 Exposed Pad 8 EK Suffix Only 9 10 26 25 24 23 11 22 12 21 13 20 25 24 3 22 SP5 SP3 4 21 SP4 SG0 5 20 SG13 SG1 6 19 SG12 SG2 7 18 SG11 SG3 8 17 SG10 9 10 11 12 13 14 15 16 SG9 SP2 SG8 SP6 SG7 SP7 SP1 WAKE_B 17 26 VBATP 16 27 SG6 18 28 23 1 SG5 19 15 29 2 SP0 SG4 14 30 INT_B 4 32 31 AMUX 30 VDDQ 3 MISO VDDQ AMUX INT_B SP7 SP6 SP5 SP4 SG13 SG12 SG11 SG10 SG9 SG8 SG7 WAKE_B GND 31 MISO 32 2 MOSI 1 SCLK CS_B GND MOSI SCLK CS_B SP0 SP1 SP2 SP3 SG0 SG1 SG2 SG3 SG4 SG5 SG6 VBATP Figure 3. 33978 SOICW-EP and QFN (WF-Type) pinouts 3.2 Pin definitions Table 2. 33978 pin definitions Pin number Pin number Pin name SOIC QFN Pin function Formal name Definition 1 29 GND Ground Ground Ground for logic, analog 2 30 MOSI Input/SPI SPI Slave In SPI control data input pin from the MCU 3 31 SCLK Input/SPI Serial Clock SPI control clock input pin 4 32 CS_B Input/SPI Chip Select SPI control chip select input pin 5-8 25 - 28 1-4 21 - 24 SP0 - 3 SP4 - 7 Input Programmable Switches 0 - 7 9 - 15, 18 - 24 5 - 11 14 - 20 SG0 - 6, SG7 -13 Input Switch-to-Ground Inputs 0 - 13 16 12 VBATP Power Battery Input 17 13 WAKE_B Input/Output Wake-up Open drain wake-up output. Designed to control a power supply enable pin. Input used to allow a wake-up from an external event. 29 25 INT_B Input/Output Interrupt Open-drain output to MCU. Used to indicate an input switch change of state. Used as an input to allow wake-up from LPM via an external INT_B falling event. 30 26 AMUX Output 31 27 VDDQ Input Switch to programmable input pins (SB or SG) Switch-to-ground input pins Battery supply input pin. Pin requires external reverse battery protection Analog Multiplex Output Analog multiplex output. Voltage Drain Supply 3.3 V/ 5.0 V supply. Sets SPI communication level for the MISO driver and I/O level buffer 33978 5 NXP Semiconductors Table 2. 33978 pin definitions (continued) Pin number Pin number Pin name SOIC QFN 32 28 Pin function Formal name Definition MISO Output/SPI SPI Slave Out Provides digital data from the 33978 to the MCU. EP Ground Exposed Pad It is recommended that the exposed pad is terminated to GND (pin 1) and system ground. 33978 NXP Semiconductors 6 4 General product characteristics 4.1 Maximum ratings Table 3. Maximum ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Symbol Description (rating) Min. Max. Unit Notes Electrical ratings VBATP Battery Voltage -0.3 40 V VDDQ Supply Voltage -0.3 7.0 V CS_B, MOSI, MISO, SCLK SPI Inputs/Outputs -0.3 7.0 V SGx, SPx Switch Input Range -14(4) 38 V AMUX AMUX -0.3 7.0 V INT_B INT_B -0.3 7.0 V WAKE_B -0.3 40 V WAKE_B VESD1-2 VESD1-3 VESD3-1 VESD2-1 VESD2-2 ESD Voltage * Human Body Model (HBM) (VBATP versus GND) MC33978 and MC34978 MC33978A and MC34978A * Human Body Model (HBM) (All other pins) * Machine Model (MM) * Charge Device Model (CDM) (Corners pins) * Charge Device Model (CDM) (All other pins) 2000 4000 2000 200 750 500 V (5) V (6) Contact Discharge VESD5-3 VESD5-4 VESD6-1 VESD6-2 * VBATP(8) * WAKE_B (series resistor 10 k) * SGx and SPx pins with 100 nF capacitor (100 series R) based on external protection performance(7) * SGx and SPx pins with 100 nF capacitor (50 series R) 8000 8000 15000 8000 Notes 4. Minimum value of -18 V is guaranteed by design for switch input voltage range (SGx, SPx). 5. ESD testing is performed in accordance AEC Q100, with the Human Body Model (HBM) (CZAP = 100 pF, RZAP = 1500 ), the Machine Model (MM) (CZAP = 200 pF, RZAP = 0 ), and the Charge Device Model (CDM). 6. CZAP = 330 pF, RZAP = 2.0 k (Powered and unpowered) / CZAP = 150 pF, RZAP = 330 (Unpowered) 7. 8. 15000V capability in powered condition, 8000V in all other conditions. External component requirements at system level: Cbulk = 100uF aluminum electrolytic capacitor Cbypass= 100nF 37 % ceramic capacitor Reverse blocking diode from Battery to VBATP (0.6 V < VF < 1 V). See Figure 23, Typical application diagram. 33978 7 NXP Semiconductors 4.2 Thermal characteristics Table 4. Thermal ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Symbol Description (rating) Min. Max. Unit Operating Temperature * Ambient * Junction -40 -40 125 150 C TSTG Storage Temperature -65 150 C TPPRT Peak Package Reflow Temperature During Reflow - - C Notes Thermal ratings TA TJ Thermal resistance RJA Junction-to-Ambient, Natural Convection, Single-Layer Board * 32 SOIC-EP * 32 QFN 79 94 C/W (9),(10) RJB Junction-to-Board * 32 SOIC-EP * 32 QFN 9.0 12 C/W (11) RJC Junction-to-Case (Bottom) * 32 SOIC-EP * 32 QFN 3.0 2.0 C/W (12) Junction-to-Package (Top), Natural convection * 32 SOIC-EP * 32 QFN 11 2.0 C/W (13) JT Package dissipation ratings TSD Thermal Shutdown * 32 SOIC-EP * 32 QFN 155 185 C TSDH Thermal Shutdown Hysteresis * 32 SOIC-EP * 32 QFN 3.0 15 C Notes 9. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 10. Per JEDEC JESD51-2 with natural convection for horizontally oriented board. Board meets JESD51-9 specification for 1s or 2s2p board, respectively. 11. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 12. Thermal resistance between the die and the solder pad on the bottom of the package based on simulation without any interface resistance. 13. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD512. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. 33978 NXP Semiconductors 8 4.3 Operating conditions This section describes the operating conditions of the device. Conditions apply to the following data, unless otherwise noted. Table 5. Operating conditions All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Symbol Ratings Min. Max. Unit VBATP Battery Voltage 4.5 36 V VDDQ Supply Voltage 3.0 5.25 V CS_B, MOSI, MISO, SCLK SPI Inputs / Outputs 3.0 5.25 V SGx, SPx Switch Input Range -1.0 36 V AMUX, INT_B 0.0 5.25 V WAKE_B 0.0 36 V AMUX, INT_B WAKE_B 4.4 Notes Electrical characteristics 4.4.1 Static electrical characteristics Table 6. Static electrical characteristics TA = - 40 C to +125 C, VDDQ = 3.1 V to 5.25 V, VBATP = 6.0 V to 28.0 V, unless otherwise noted. Symbol Characteristic Min. Typ. Max. Units VBATP Supply Voltage POR * VBATP Supply Power on Reset voltage. 2.7 3.3 3.8 V VBATP Undervoltage Rising Threshold -- 4.3 4.5 V VBATP Undervoltage Hysteresis 250 -- 500 mV VBATP Overvoltage Rising Threshold 32 -- 37 V VBATP Overvoltage Hysteresis 1.5 -- 3.0 V VBATP Supply Current * All switches open, Normal mode, Tri-state disabled (all channels) -- 7.0 12 mA -- -- -- -- 40 40 A VBATP Polling Current * Polling 64 ms, 11 inputs of wake enabled -- -- 20 A Normal mode (IVDDQ) * SCLK, MOSI, WakeB = 0 V, CS_B, INT_B =VDDQ, no SPI communication, AMUX selected no input -- -- 500 uA Logic Low-power mode Supply Current * SCLK, MOSI = 0 V, CS_B, INT_B, WAKE_B = VDDQ, no SPI communication -- -- 10 A Ground Offset * Ground offset of Global pins to IC ground -1.0 -- 1.0 V VDDQ Undervoltage Falling Threshold 2.2 -- 2.8 V VDDQ Undervoltage Hysteresis 150 -- 350 mV Notes Power input VBATP(POR) VBATPUV VBATPUVHYS VBATPOV VBATPOVHYS IBAT(ON) IBATP,IQ,LPM,P IBATP,IQ,LPM,F IPOLLING,IQ IVDDQ,NORMAL IVDDQ,LPM VGNDOFFSET VDDQUV VDDQUVHYS VBATP Low-power Mode Supply Current (polling disabled) * Parametric VBATP, 6.0 V < VBATP < 28 V * Functional Low VBATP, 4.5 V < VBATP < 6.0 V (14) 33978 9 NXP Semiconductors Table 6. Static electrical characteristics (continued) TA = - 40 C to +125 C, VDDQ = 3.1 V to 5.25 V, VBATP = 6.0 V to 28.0 V, unless otherwise noted. Symbol Characteristic Min. Typ. Max. Units ILEAKSG_GND Leakage (SGx/SPx pins) to GND * Inputs tri-stated, analog mux selected for each input, voltage at SGx = VBATP -- -- 2.0 A ILEAKSG_BAT Leakage (SGx/SPx pins) to Battery * Inputs tri-stated, analog mux selected for each input, voltage at SGx = GND -- -- 2.0 A SG Sustain current / Mode 0 Wetting current * VBATP 6.0 to 28 V 1.6 2.0 2.4 SG Sustain current / Mode 0 Wetting current LV * VBATP 4.5 V to 6.0 V 1.0 -- 2.4 SB Sustain current / Mode 0 Wetting current 1.75 2.2 2.85 mA -- mA % Notes Switch input ISUSSG ISUSSGLV ISUSSB IWET IWETSG Wetting current level (SG & SB) * Mode 1 = 6mA * Mode 2 = 8mA * Mode 3 = 10mA * Mode 4 = 12mA * Mode 5 = 14mA * Mode 6 = 16mA * Mode 7 = 20mA -- SG wetting current tolerance * Mode 1 to 7 6 8 10 12 14 16 20 mA mA (15) -10 -- 10 2.0 2.0 2.0 2.0 2.0 2.0 2.0 -- -- -- -- -- -- -- 6.6 8.8 11.0 13.2 15.4 17.6 22.0 SB wetting current tolerance * Mode 1 to 7 -20 -- 20 IMATCH(SUS) Sustain Current Matching Between Channels -- -- 10 % (16), (17) IMATCH(WET) Wetting Current Matching Between Channels -- -- 6.0 % (18), (19) Switch Detection Threshold 3.7 4.0 4.3 V (20) 0.55 * VBATP -- 4.3 V IWETSGLV IWETSB VICTHR VICTHRLV SG wetting current tolerance LV (VBATP 4.5 to * Mode 1 = 6mA * Mode 2 = 8mA * Mode 3 = 10mA * Mode 4 = 12mA * Mode 5 = 14mA * Mode 6 = 16mA * Mode 7 = 20mA 6.0V)(15) Switch Detection Threshold Low Battery * VBATP 4.5 V to 6.0 V mA % VICTHRLPM Switch Detection Threshold Low-power Mode (SG only) 100 -- 300 mV VICTHRH Switch Detection Threshold Hysteresis (4.0 V threshold) 80 -- 300 mV VICTH2P5 Input Threshold 2.5 V, * Used for Comp Only and for AMUX Hardwired Select (SG1/2/3) 2.0 2.5 3.0 V IACTIVEPOLLSG Low-power Mode Polling Current SG * VBATP 4.5 V to 28 V 0.7 1.0 1.44 mA IACTIVEPOLLSB Low-power Mode Polling Current SB 1.75 2.2 2.85 mA (21) 33978 NXP Semiconductors 10 Table 6. Static electrical characteristics (continued) TA = - 40 C to +125 C, VDDQ = 3.1 V to 5.25 V, VBATP = 6.0 V to 28.0 V, unless otherwise noted. Symbol Characteristic Min. Typ. Max. Units -2.0 -- 2.0 A Notes Digital interface IHZ Tri-state Leakage Current (MISO) * VDDQ = 0.0 to VDDQ VINLOGIC Input Logic Voltage Thresholds * SI, SCLK, CS_B, INT_B VDDQ * 0.25 -- VDDQ * 0.7 V VINLOGICHYS Input Logic Hysteresis * SI, SCLK, CS_B, INT_B 300 -- -- mV VINLOGICWAKE Input Logic Voltage Threshold WAKE_B 0.8 1.25 1.7 V VINWAKEBHYS Input Logic Voltage Hysteresis WAKE_B 200 -- 800 mV ISCLK, IMOSI SCLK / MOSI Input Current * SCLK / MOSI = 0 V -3.0 -- 3.0 A ISCLK, IMOSI SCLK / MOSI Pull-down Current * SCLK / MOSI = VDDQ 30 -- 100 A ICS_BH CS_B Input Current * CS_B = VDDQ -10 -- 10 A RCS_BL CS_B Pull-up Resistor to VDDQ * CS_B = 0.0 V 40 125 270 k VOHMISO MISO High-side Output Voltage * IOHMISO = -1.0 mA VDDQ - 0.8 -- VDDQ V VOLMISO MISO Low-side Output Voltage * IOLMISO = 1.0 mA -- -- 0.4 V Input Capacitance on SCLK, MOSI, Tri-state MISO (GBD) -- -- 20 pF -10 -15 -- -- 10 15 mV CIN Analog MUX output VOFFSET Input Offset Voltage When Selected as Analog * EK suffix (SOICW) * ES suffix (QFN at TA = -40 C to 25 C) VOLAMUX Analog Operational Amplifier Output Voltage * Sink 1.0 mA -- -- 50 mV VOHAMUX Analog Operational Amplifier Output Voltage * Source 1.0 mA VDDQ - 0.1 -- -- V -- 8.0 -- mV/C (22) AMUX selectable outputs Temp-Coeff Chip Temperature Sensor Coefficient VBATSNSACC Battery Sense (SG5 config) Accuracy * Battery voltage (SG5 input) divided by 6 * Accuracy over full temperature range -5.0 -- 5.0 % VBATSNSDIV Divider By 6 coefficient accuracy * Offset over operating voltage range (VBATP=6.0 V to 28 V) -3.0 -- 3.0 % (23) 33978 11 NXP Semiconductors Table 6. Static electrical characteristics (continued) TA = - 40 C to +125 C, VDDQ = 3.1 V to 5.25 V, VBATP = 6.0 V to 28.0 V, unless otherwise noted. Symbol Characteristic Min. Typ. Max. Units Notes INT_B VOLINT INT_B Output Low Voltage * IOUT = 1.0 mA -- 0.2 0.5 V VOHINT INT_B Output High Voltage * INT_B = Open-circuit VDDQ - 0.5 -- VDDQ V Pull-up Resistor to VDDQ 40 125 270 k Leakage Current INT_B * INT_B pulled up to VDDQ -- -- 1.0 A RPU ILEAKINT_B Temperature limit tFLAG Temperature Warning * First flag to trip 105 120 135 C tLIM Temperature Monitor 155 -- 185 C (24) Temperature Monitor Hysteresis 5.0 -- 15 C (24) RWAKE_B(RPU) WAKE_B Internal pull-up Resistor to VDDQ 40 125 270 k VWAKE_B(VOH) WAKE_B Voltage High * WAKE_B = Open-circuit VDDQ -1.0 -- VDDQ V VWAKE_B(VOL) WAKE_B Voltage Low * WAKE_B = 1.0 mA (RPU to VBATP = 16 V) -- -- 0.4 V IWAKE_BLEAK WAKE_B Leakage * WAKE_B pulled up to VBATP = 16 V through 10 k -- -- 1.0 A tLIM(HYS) WAKE_B Notes 14. Guaranteed by design 15. During low voltage range operation SG wetting current may be limited when there is not enough headroom between VBATP and SG pin voltage. 16. (ISUS(MAX)- ISUS(MIN)) X 100/ISUS(MIN) 17. 18. Sustain current source (SGs only) (IWET(MAX) - IWET(MIN)) X 100/IWET(MIN) 19. 20. Wetting current source (SGs only) The input comparator threshold decreases when VBATP 6.0 V. 21. SP (as SB) only use the 4.0 V VICTHR for LPM wake-up detection. 22. For applications requiring a tight AMUX offset through the whole operating range, it is recommended to use the MC33978AEK or MC34978AEK (SOICW package) variant. Calibration of divider ratio can be done at VBAT = 12 V, 25 C to achieve a higher accuracy. See Figure 4 for AMUX offset linearity waveform through the operating voltage range. Guaranteed by characterization in the Development Phase, parameter not tested. 23. 24. 33978 NXP Semiconductors 12 4.4.2 Dynamic electrical characteristics Table 7. Dynamic electrical characteristics TA = -40 C to +125 C. VDDQ = 3.1 V to 5.25 V, VBATP = 6.0 V to 28 V, unless otherwise specified. All SPI timing is performed with a 100 pF load on MISO, unless otherwise noted. Symbol Parameter Min. Typ. Max. Units POR to Active time * Undervoltage to Normal mode 250 340 450 s Pulse Wetting Current Timer * Normal mode 17 20 23 ms Interrupt Delay Time * Normal mode -- -- 18.5 s Polling Timer Accuracy * Low-power mode -- -- 15 % Interrupt Timer Accuracy * Low-power mode -- -- 15 % Tactivepoll Timer SG 49.5 58 66.5 s Tactivepoll Timer SB * SBPOLLTIME=0 * SBPOLLTIME=1 1.0 49.5 1.2 58 1.4 66.5 ms s Input Glitch Filter Timer * Normal mode 5.0 -- 18 s LPM Debounce Additional Time * Low-power mode 1.0 1.2 1.4 ms AMUX Access Time (Selected Output to Selected Output) * CMUX = 1.0 nF, Rising edge of CS_B to selected -- (26) -- s AMUX Access Time (Tristate to ON) * CMUX = 1.0 nF, Rising edge of CS_B to selected -- -- 20 s OSCTOLLPM Oscillator Tolerance at 192 kHz in Low-power Mode -15 -- 15 % OSCTOLNOR Oscillator Tolerance Normal Mode at 4.0 MHz -15 -- 15 % INT Pulse Duration * Interrupt occurs or INT_B request 90 100 110 s fOP Transfer Frequency -- -- 8.0 MHz tSCK SCLK Period * Figure 7 - 1 160 -- -- ns tLEAD Enable Lead Time * Figure 7 - 2 140 -- -- ns tLAG Enable Lag Time * Figure 7 - 3 50 -- -- ns tSCKHS SCLK High Time * Figure 7 - 4 56 -- -- ns Notes General tACTIVE Switch input tPULSE(ON) tINT-DLY tPOLLING_TIMER tINT-TIMER tACTIVEPOLLSGTI ME tACTIVEPOLLSBTI ME tGLITCHTIMER tDEBOUNCE AMUX output AMUXVALID AMUXVALIDTS Oscillator Interrupt INTPULSE SPI interface 33978 13 NXP Semiconductors Table 7. Dynamic electrical characteristics (continued) TA = -40 C to +125 C. VDDQ = 3.1 V to 5.25 V, VBATP = 6.0 V to 28 V, unless otherwise specified. All SPI timing is performed with a 100 pF load on MISO, unless otherwise noted. Symbol Parameter Min. Typ. Max. Units Notes SCLK Low Time * Figure 7 - 5 56 -- -- ns tSUS MOSI Input Setup Time * Figure 7 - 6 16 -- -- ns tHS MOSI Input Hold Time * Figure 7 - 7 20 -- -- ns tA MISO Access Time * Figure 7 - 8 -- -- 116 ns tDIS MISO Disable Time (25) * Figure 7 - 9 -- -- 100 ns tVS MISO Output Valid Time * Figure 7 - 10 -- -- 116 ns tHO MISO Output Hold Time (No cap on MISO) * Figure 7 - 11 20 -- -- ns tRO Rise Time * Figure 7 - 12 -- -- 30 ns (25) tFO Fall Time * Figure 7 - 13 -- -- 30 ns (25) tCSN CS_B Negated Time * Figure 7 - 14 500 -- -- ns -- 755 1000 s SPI interface (continued) tSCKLS WAKE-UP tCSB_WAKEUP LPM mode wake-up time triggered by edge of CS_B (27) Notes 25. Guaranteed by characterization. 26. AMUX settling time to be within the 10 mV offset specification. AMUXVALID is dependant of the voltage step applied on the input SGx/SPx pin or the difference between the first and second channel selected as the multiplexed analog output. See Figure 9 for a typical AMUX access time VS voltage step waveform. 27. The parameter is guaranteed at VBATP = 4.5 V to 28 V. 33978 NXP Semiconductors 14 Divide By 6 Coefficient Accuracy 6.04 6.03 Divider factor 6.02 6.01 6 25C 5.99 5.98 5.97 5.96 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VBATP (Volts) Figure 4. Divide by 6 coefficient accuracy LPM CLK SG_Pin tglitchTIMER Input Glitch filter timer 500ns tINT- DLY INT_B Figure 5. Glitch filter and interrupt delay timers LPM CLK SG_Pin INT_B tINT- DLY INTPulse Figure 6. Interrupt pulse timer 33978 15 NXP Semiconductors 3 14 CSb 1 4 2 SCLK 5 10 8 MISO DATA MSB OUT MOSI DON'T CARE LSB OUT 12 13 7 6 9 11 MSB IN DATA LSB IN Figure 7. SPI timing diagram +5.0 V VDDQ 4.0 V MISO 1kohm 1.0 V MISO 0V 1kohm 9 CS_B Figure 8. MISO loading for disable time measurement AMUX settling time vs voltage step 250 Settling time (us) 200 150 100 AMUX Access Time 50 0 0 500 1000 1500 2000 2500 3000 Step Size (mV) 3500 4000 4500 5000 Figure 9. AMUX access time waveform 33978 NXP Semiconductors 16 5 General description The 33978 is designed to detect the closing and opening of up to 22 switch contacts. The switch status, either open or closed, is transferred to the microprocessor unit (MCU) through a serial peripheral interface (SPI). Individually selectable input currents are available in Normal and Low-power (LPM) modes, as needed for the application. It also features a 24-to-1 analog multiplexer for reading inputs as analog. The analog input signal is buffered and provided on the AMUX output pin for the MCU to read. A battery and temperature monitor are included in the IC and available via the AMUX pin. The 33978 device has two modes of operation, Normal and Low-power mode (LPM). Normal mode allows programming of the device and supplies switch contacts with pull-up or pull-down current as it monitors the change of state of switches. The LPM provides low quiescent current, which makes the 33978 ideal for automotive and industrial products requiring low sleep-state currents. 5.1 Features * * * * * * * Fully functional operation from 4.5 V to 36 V Full parametric operation from 6.0 V to 28 V Low-power mode current IBATP = 30 A and IDDQ = 10 A 22 Switch detection channels * 14 Switch-to-Ground (SG) inputs * Eight Programmable switch (SP) inputs * Switch-to-Ground (SG) or Switch-to-Battery (SB) * Operating switch input voltage range from -1.0 V to 36 V * Selectable wetting current (2, 6, 8, 10, 12, 14, 16, or 20 mA) * Programmable wetting operation (Pulse or Continuous) * Selectable wake-up on change of state 24 to 1 Analog Multiplexer * Buffered AMUX output from SG/SP channels * Integrated divider by 6 on SG5 for battery voltage sensing * Integrated die temperature sensing through AMUX output * Two or three pin hardwire AMUX selection. Active interrupt (INT_B) on change-of-switch state Direct MCU Interface through 3.3 V / 5.0 V SPI protocol 33978 17 NXP Semiconductors 5.2 Functional block diagram 33978 Functional Internal Block Diagram Switch Status Detection Input Power VBATP Battery Supply VDDQ Logic Supply Bias & References 1.25 V internal Bandgap 4.0 V SW detection reference. 192 kHz LPM Oscillator 4.0 MHz Oscillator 8 x Programmable Switch SG0 - SG13 SP0 - SP7 Switch to Ground (SG) Only Switch to Ground (SG) Switch to Battery (SB) Selectable Wetting Current Level Pulse/Continuous Wetting Current Analog Multiplexer (AMUX) Logic and Control WAKE_B I/O 14 x Switch to Ground INT_B I/O SPI Serial Communication & Registers 24 to 1 SPI AMUX select Hardwire selectable SPx/SGx Inputs to AMUX Battery Voltage sensing (divided by 6 ) Fault Detection and Protection Over Temperature Protection OV Detection VBATP UV detect SPI Error detect HASH error detect Die Temperature Sensing Modes of Operation Normal Mode Low Power Mode SPI communication/ Switch status read Programmable Polling/ Interrupt Time Figure 10. Functional block diagram 33978 NXP Semiconductors 18 6 General IC functional description The 33978 device interacts with many connections outside the module and near the end user. The IC detects changes in switch state and reports the information to the MCU via the SPI protocol. The input pins generally connected to switches located outside the module and in proximity to battery in car harnesses. Consequently, the IC must have some external protection including an ESD capacitor and series resistors, to ensure the energy from the various pulses are limited at the IC. The IC requires a blocking diode be used on the VBATP pin to protect from a reverse battery condition. The inputs are capable of surviving reverse battery without a blocking diode and also contain an internal blocking diode from the input to the power supply (VBATP), to ensure there is no backfeeding of voltage/current into the IC, when the voltage on the input is higher than the VBATP pin. 6.1 Battery voltage ranges The 33978 device operates from 4.5 V VBATP 36 V and is capable to withstand up to 40 V. The IC operates functionally from 4.5 V < VBATP < 6.0 V, but with degraded parametrics values. Voltages in excess of 40 V must be clamped externally in order to protect the IC from destruction. The VBATP pin must be isolated from the main battery node by a diode. 6.1.1 Load dump (overvoltage) During load dump the 33978 operates properly up to the VBATP overvoltage. Voltages greater than load dump (~32 V) causes the current sources to be limited to ~2.0 mA, but the register values are maintained. Upon leaving this overvoltage condition, the original setup is returned and normal operation begins again. 6.1.2 Jump start (double battery) During a jump start (double battery) condition, the device functions normally and meets all the specified parametric values. No internal faults are set and no abnormal operation noted as a result of operating in this range. 6.1.3 Normal battery range The normal voltage range is fully functional with all parametrics in the given specification. 6.1.4 Low-voltage range (degraded parametrics) In the VBATP range between 4.5 V to 6.0 V the 33978 functions normally, but has some degraded parametric values. The SPI functions normally with no false reporting. The degraded parameters are noted in Table 6 and Table 7. During this condition, the input comparator threshold is reduced from 4.0 V and remain ratiometrically adjusted, according to the battery level. 6.1.5 Undervoltage lockout During undervoltage lockout, the MISO output is tri-stated to avoid any data from being transmitted from the 33978. Any CS_B pulses are ignored in this voltage range. If the battery enters this range at any point (even during a SPI word), the 33978 ignores the word and enters lockout mode. A SPI bit register is available to notify the MCU that the 33978 has seen an undervoltage lockout condition once the battery is high enough to leave this range. 6.1.6 Power on reset (POR) activated The Power on Reset is activated when the VBATP is within the 2.7 V to 3.8 V range. During the POR all SPI registers are reset to default values and SPI operation is disabled. The 33978 is initialized after the POR is de-asserted. A SPI bit in the device configuration register is used to note a POR occurrence and all SPI registers are reset to the default values. 6.1.7 No operation The device does not function and no switch detection is possible. 33978 19 NXP Semiconductors VBATP (IC Level) Battery Voltage (System Level) 41 V Over Voltage 40 V Overvoltage 37 V Load Dump 36 V Functional 29 V 28 V Normal Mode Full Parametrics Normal Battery 6.0 V 7.0 V Low Battery 5.5 V 4.8 V 3.7 V 0V Degraded Parametrics Undervoltage lockout POR No Operation 4.5 V 3.8 V 2.7 V Reset 0V Figure 11. Battery voltage range 6.2 Power sequencing conditions The chip uses two supplies as inputs into the device for various usage. The pins are VBATP and VDDQ. The VBATP pin is the power supply for the chip where the internal supplies are generated and power supply for the SG circuits. The VDDQ pin is used for the I/O buffer supply to talk to the MCU or other logic level devices, as well as AMUX. The INT_B pin is held low upon POR until the IC is ready to operate and communicate. Power can be applied in various ways to the 33978 and the following states are possible: 6.2.1 VBATP before VDDQ The normal condition for operation is the application of VBATP and then VDDQ. The chip begin to operate logically in the default state but without the ability to drive logic pins. When the VDDQ supply is available the chip is able to communicate correctly. The IC maintains its logical state (register settings) with functional behavior consistent with logical state. No SPI communications can occur. 6.2.2 VDDQ before VBATP The VDDQ supply in some cases may be available before the VBATP supply is ready. In this scenario, there is no back feeding current into the VDDQ pin that could potentially turn on the device into an unknown state. VDDQ is isolated from VBATP circuits and the device is off until VBATP is applied; when VBATP is available the device powers up the internal rails and logic within tACTIVE time. Communication is undefined until the tACTIVE time and becomes available after this time frame. 6.2.3 VBATP okay, VDDQ lost After power up, it is possible that the VDDQ may turn off or be lost. In this case, the chip remains in the current state but is not able to communicate. After the VDDQ pin is available again, the chip is ready to communicate. 6.2.4 VDDQ okay, VBATP lost After power up, the VBATP supply could be lost. The operation is consistent as when VDDQ is available before VBATP. 33978 NXP Semiconductors 20 7 Functional block description 7.1 State diagram IC OFF VBATP applied RESET VBAT applied > por VBATP > UV threshold Wait 50 s Read fuses VBAT too low: POR SPI RESET command UV OV / OT Iwet-> Isus VBATP > OV or OT VBATP < UV Not VBATP > OV or OT Run Normal Mode Detect change in switch status (opn/close) Wake Event SPI CMD Polling time expires Low Power Mode Polling Polling timer initiates Figure 12. 33978 state diagram 7.1.1 State machine After power up, the IC enters into the device state machine, as illustrated in Figure 12. The voltage on VBATP begins to power the internal oscillators and regulator supplies. The POR is based on the internal 2.5 V digital core rail. When the internal logic regulator reaches approximately 1.8 V (typically 3.3 V on the VBATP node), the IC enters into the UV range. Below the POR threshold, the IC is in RESET mode where no activity occurs. 33978 21 NXP Semiconductors 7.1.2 UV: undervoltage lockout After the POR circuit has reset the logic, the IC is in undervoltage. In this state, the IC remembers all register conditions, but is in a lockout mode, where no SPI communication is allowed. The AMUX is inactive and the current sources are off. The user does not receive a valid response from the MISO, as it is disabled in this state. The chip oscillators (4.0 MHz for most normal mode activities, 192 kHz for LPM, and limited normal mode functions) are turned on in the UV state. The chip moves to the Read fuses state when the VBATP voltage rises above the UV threshold (~4.3 V rising). The internal fuses read in approximately 50 s and the chip enters the Normal mode. 7.1.3 Normal mode In normal mode, the chip operates as selected in the available registers. Any command may be loaded in normal mode, although not all (Low-power mode) registers are used in the Normal mode. All the LPM registers must be programmed in Normal mode as the SPI is not active in LPM. The Normal mode of the chip is used to operate the AMUX, communicate via the SPI, Interrupt the IC, wetting and sustain currents, as well as the thresholds available to use. The WAKE_B pin is asserted (low) in Normal mode and can be used to enable a power supply (ENABLE_B). Various fault detections are available in this mode including overvoltage, overtemperature, thermal warning, SPI errors, and Hash faults. 7.1.4 Low-power mode When the user needs to lower the IC current consumption, a low-power mode is used. The only method to enter LPM is through a SPI word. After the chip is in low-power mode, the majority of circuitry is turned off including most power rails, the 4.0 MHz oscillator, and all the fault detection circuits. This mode is the lowest current consumption mode on the chip. If a fault occurs while the chip is in this mode, the chip does not see or register the fault (does not report via the SPI when awakened). Some items may wake the IC in this mode, including the interrupt timer, falling edge of INT_B, CS_B, or WAKE_B (configurable), or a comparator only mode switch detection. 7.1.5 Polling mode The 33978 uses a polling mode which periodically (selectable in LPM config register) interrogates the input pins to determine in what state the pins are, and decide if there was a change of state from when the chip was in Normal mode. There are various configurations for this mode, which allow the user greater flexibility in operation. This mode uses the current sources to pull-up (SG) or down (SB) to determine if a switch is open or closed. More information is available in section 7.2, "Low-power mode operation". In the case of a low VBATP, the polling pauses and waits until the VBATP rises out of UV or a POR occurs. The pause of the polling ensures all of the internal rails, currents, and thresholds are up at the required levels to accurately detect open or closed switches. The chip does not wake-up in this condition and simply waits for the VBATP voltage to rise or cause a POR. After the polling ends, the chip either returns to the low-power mode, or enters Normal mode when a wake event was detected. Other events may wake the chip as well, such as the falling edge of CS_B, INT_B, or WAKE_B (configurable). A comparator only mode switch detection is always on in LPM or Polling mode, so a change of state for those inputs would effectively wake the IC in Polling mode as well. If the Wake-up enable bits are disable on all channels (SG and SP) the device will not wake up with a change of state on any of the input pins; in this case, the device will disable the polling timer to allow the lowest current consumption during low-power mode. 7.2 Low-power mode operation Low-power mode (LPM) is used to reduce system quiescent currents. LPM may be entered only by sending the Enter Low-power mode command. All register settings programmed in Normal mode are maintained while in LPM. The 33978 exits LPM and enter Normal mode when any of the following events occur: * Input switch change of state (when enabled) * Interrupt timer expire * Falling edge of WAKE_B (as set by the device configuration register) * Falling edge of INT_B (with VDDQ = 5.0 V) * Falling edge of CS_B (with VDDQ = 5.0 V) * Power-ON Reset (POR) The VDDQ supply may be removed from the device during LPM, however removing VDDQ from the device disables a wake-up from falling edge of INT_B and CS_B. The IC checks the status of VDDQ after a falling edge of WAKE_B (as selected in the device configuration register), INT_B and CS_B. The IC returns to LPM and does not report a Wake event, if VDDQ is low. If the VDDQ is high, the IC wakes up and reports the Wake event. In cases where CS_B is used to wake the device, the first MISO data message is not valid. 33978 NXP Semiconductors 22 The LPM command contains settings for two programmable registers: the interrupt timer and the polling timer, as shown in Table 26. The interrupt timer is used as a periodic wake-up timer. When the timer expires, an interrupt is generated and the device enters Normal mode. The polling timer is used periodically to poll the inputs during Low-power mode to check for change of states. The tACTIVEPOLL time is the length of time the part is active during the polling timer to check for change of state. The Low-power mode voltage threshold allows the user to determine the noise immunity versus lower current levels that polling allows. Figure 14 shows the polling operation. When polling and Interrupt timer coincide, the Interrupt timer wakes the device and the polling does not occur. When an input is determined to meet the condition Open (when entering LPM), yet while Open (on polling event) the chip does not continue the polling event for that input(s) to lower current in the chip (Figure 13 shows SG, SB is logically the same). Compare voltage to initial (Delta > 0.25 or > 4.0v) End Polling (current off if no change detected) LPM Voltage threshold (~0.25v) La tc h vo lt a ge Voltage on SG pin 55s Polling timer (64ms def) Figure 13. Low-power mode polling check Go To LPM CS_B 64ms (config) Normal Normal Mode LPM Polling Time 20us Polling startup 78us Tactive time 58us 330uA IC Current 20uA X * 1mA SG (2mA SB) Load Current 0uA Figure 14. Low-power mode typical timing 33978 23 NXP Semiconductors VBATP VDDQ Wake up from Interrupt Timer expire WAKE_B INT_B CS_B Wake up from Closed Switch SGn Power - up Normal Mode Tri- state Command Sleep Command Sleep Mode Normal Mode Sleep Command Sleep Mode Normal Mode Sleep Command Figure 15. Low-power mode to normal mode operation 7.3 Input functional block The SGx pins are switch-to-ground inputs only (pull-up current sources). The SPx pins are configurable as either switch to ground or switch to battery (pull-up and pull-down current sources). The input is compared with a 4.0 V (input comparator threshold configurable) reference. Voltages greater than the input comparator threshold value are considered open for SG pins and closed for SB configuration. Voltages less than the input comparator threshold value are considered closed for SG pins and open for the SB configurations. Programming features are defined in the SPI control register definition section of this data sheet. The input comparator has hysteresis with the thresholds based on the closing of the switch (falling on SG, rising on SB). The user must take care to keep power conditions within acceptable limits (package is capable of 2.0 W). Using many of the inputs with continuous wetting current levels causes overheating of the IC and may cause an overtemperature (OT) event to occur. 33978 NXP Semiconductors 24 VBATP Pre-reg = ~8v 6 - 20 mA 2.0 mA 1.0mA (LPM) To AMUX To SPI 4.0 V ref comparator Or 250mV Delta V Or 2.5v Comparator only Figure 16. SG block diagram 33978 25 NXP Semiconductors VBATP Pre-reg 6 - 20 mA 2.0 mA 1.0mA (LPM) To SPI 4.0 V ref comparator 6 - 20 mA 2.0 mA 21.0mA (LPM) Figure 17. SP block diagram 7.4 Oscillator and timer control functional block Two oscillators are generated in this block. A 4.0 MHz clock is used in Normal mode only, as well as a Low-power mode 192 kHz clock, which is on all the time. All timers are generated from these oscillators. The oscillator accuracy is 15 % for both, the 4.0 MHz clock and the 192 kHz clock. No calibration is needed and the accuracy is over voltage and temperature. 7.5 Temperature monitor and control functional block The device has multiple thermal limit (tLIM) cells to detect thermal excursions in excess of 155 C. The tLIM cells from various locations on the IC are logically ORed together and communicated to the MCU as one tLIM fault. When the tLIM value is seen, the wetting current is lowered to 2.0 mA until the temperature has decreased beyond the tLIM(HYS) value (the sustain current remains on or as selected). A hysteresis value of 15 C exists to keep the device from cycling. A thermal flag also exists to alert the system to increasing temperatures more than approximately 120 C. 7.6 WAKE_B control functional block The WAKE_B pin can operate as an open-drain output or a wake-up input. In the Normal Mode, the WAKE_B pin is LOW. In the Lowpower mode, the WAKE_B pin is pulled HIGH. The WAKE_B pin has an internal pull-up to VDDQ supply with an internal series diode to allow an external pull-up to VBATP if required. 33978 NXP Semiconductors 26 As an input, in Low-power mode with the WAKE_B pin pulled HIGH, when commanded LOW by MCU, the falling edge of WAKE_B places the MC33978 in Normal mode. In Low-power mode if VDDQ goes low, the WAKE_B pin can still wake the device based on the status of the WAKE_B bit in the device configuration register, this allows the user to pull the WAKE_B pin up to VBATP such that it can be used in VDDQ off setup. As an output, WAKE_B pin can drive either an MCU input or the EnableB of a regulator (possibly for VDDQ). WAKE_B is driven Low during Normal mode regardless of the state of VDDQ. When the 33978 is in LPM, the WAKE_B pin is released and is expected to be pulled up internally to VDDQ or externally to VBATP. When a valid wake-up event is detected, the 33978 wakes up from LPM and the WAKE_B is driven Low (regardless of the state of VDDQ). 7.7 INT_B functional block INT_B is an input/output pin in the 33978 device to indicate an interrupt event has occurred, as well as receiving interrupts from other devices when the INT_B pins are wired ORed. The INT_B pin is an open-drain output with an internal pull-up to VDDQ. In Normal mode, a switch state change triggers the INT_B pin (when enabled). The INT_B pin and INT_B bit in the SPI register are latched on the falling edge of CS_B. This permits the MCU to determine the origin of the interrupt. When two 33978 devices are used, only the device initiating the interrupt has the INT_B bit set. The INT_B pin and INTflg bit are cleared 1.0 s after the falling edge of CS B. The INT_B pin does not clear with the rising edge of CS_B if a switch contact change has occurred while CS_B was Low. In a multiple 33978 device system with WAKE_B High and VDDQ on (Low-power mode), the falling edge of INT_B places all 33978s in Normal mode. The INT_B has the option of a pulsed output (pulsed low for INTpulse duration) or a latched low output. The default case is the latched low operation; the pulsed option is selectable via the SPI. An INT_B request by the MCU can be done by a SPI word and results in an INTPULSE of 100 s duration on the INT_B pin. The chip causes an INT_B assertion for the following cases: 1. A change of state is detected 2. Interrupt timer expires 3. Any Wake-up event 4. Any faults detected 5. After a POR, the INT_B pin states asserted during startup until the chip is ready to communicate 7.8 AMUX functional block The analog voltage on switch inputs may be read by the MCU using the analog command (Table 43). Internal to the IC is a 24-to-1 analog multiplexer. The voltage present on the selected input pin is buffered and made available on the AMUX output pin. The output pin is clamped to a maximum of VDDQ regardless of the higher voltages present on the input pin. After an input has been selected as the analog, the corresponding bit in the next MISO data stream is logic [0]. When selecting a channel to be read as analog input, the user can also set the current level allowed in the AMUX output. Current level can be set to the programmed wetting current for the selected channel or set to high-impedance as defined in Table 42. When selecting an input to be sent to the AMUX output, that input is not polled or a wake-up enabled input from Low-power mode. The user should set the AMUX to "No input selected" or "Temp diode" before entering Low-power mode. The AMUX pin is not active during Low-power mode. The SG5 pin can also be used as a VBATP sense pin. An internal resistor divider of 1/6 is provided for conditioning the VBATP higher voltage to a level within the 0 V to VDDQ range. Besides the default SPI input selection method, the AMUX has two hardwire operation such that the user can select an specific input channel by physically driving the SG1, SG2 or SG3 pin (HW 3-bit), or by driving the SG1 and SG2 pins (HW 2-bit) as shown in Table 9 and Table 10. When using the AMUX hardwired options, the SG1, SG2, and SG3 inputs use a 2.5 V input voltage threshold to read a logic 0 or logic 1. Table 8 shows the AMUX selection methods configurable by the Aconfig0 and Aconfig1 bits in the Device Configuration register. Table 8. AMUX selection method Aconfig1 Aconfig0 AMUX Selection method 0 0 SPI (def) 0 1 SPI 1 0 HW 2-bit 1 1 HW 3-bit 33978 27 NXP Semiconductors Table 9. AMUX hardware 3-bit Pins [SG3, SG2, SG1] Output of AMUX 000 SG0 001 SG5 010 SG6 011 SG7 100 SG8 101 SG9 110 Temperature Diode 111 Battery Sense Table 10. AMUX hardware 2-bit Pins [SG2, SG1] Output of AMUX 00 SG0 01 SG5 10 SG6 11 SG7 Since the device is required to meet the 1.0 V offset with ground, it is imperative that the user bring the sensor ground back to the 33978 when using the AMUX for accurate measurements to ensure any ground difference does not impact the device operation. 7.9 Serial peripheral interface (SPI) The 33978 contains a serial peripheral interface consisting of Serial Clock (SCLK), Serial Data Out (MISO), Serial Data In (MOSI), and Chip Select Bar (CS_B). The SPI interface is used to provide configuration, control, and status functions; the user may read the registers contents as well as read some status bits of the IC. This device is configured as an SPI slave. All SPI transmissions to the 33978 must be done in exact increments of 32 bits (modulo 0 is ignored as well). The 33978 contains a data valid method via SCLK input to keep non-modulo-32 bit transmissions from being written into the IC. The SPI module also provides a daisy chain capability to accommodate MOSI to MISO wrap around (see Figure 21). The SPI registers have a hashing technique to ensure that the registers are consistent with the programmed values. If the hashed value does not match the register status, a SPI bit is set as well as an interrupt to alert the MCU to this issue. 7.9.1 Chip select low (CS_B) The CS_B input selects this device for serial transfers. On the falling edge of CS_B, the MISO pin is released from tri-state mode, and all status information are latched in the SPI shift register. While CS_B is asserted, register data is shifted in the MOSI pin and shifted out the MISO pin on each subsequent SCLK. On the rising edge of CS_B, the MISO pin is tri-stated and the fault register reloaded (latched) with the current filtered status data. To allow sufficient time to reload the fault registers, the CS_B pin must remain low for a minimum of tCSN prior to going high again. The CS_B input contains a pull-up current source to VDDQ to command the de-asserted state should an open-circuit condition occur. This pin has threshold compatible voltages allowing proper operation with microprocessors using a 3.3 V to 5.0 V supply. 7.9.2 Serial clock (SCLK) The SCLK input is the clock signal input for synchronization of serial data transfer. This pin has a threshold compatible voltages allowing proper operation with microprocessors using a 3.3 V to 5.0 V supply. When CS_B is asserted, both the Master Microprocessor and this device latch input data on the rising edge of SCLK. The SPI master typically shifts data out on the falling edge of SCLK, while this device shifts data out on the rising edge of SCLK, to allow more time to drive the MISO pin to the proper level. 33978 NXP Semiconductors 28 This input is used as the input for the modulo-32 bit counter validation. Any SPI transmissions which are NOT exact multiples of 32 bits (i.e. clock edges) is treated as an illegal transmission. The entire frame is aborted and no information is changed in the configuration or control registers. 7.9.3 Serial data output (MISO) The MISO output pin is in a tri-state condition when CS_B is negated. When CS_B is asserted, MISO is driven to the state of the MSB of the internal register and start shifting out the requested data from the MSB to the LSB. This pin supplies a "rail to rail" output, depending on the voltage at the VDDQ pin. 7.9.4 Serial data input (MOSI) The MOSI input takes data from the master microprocessor while CS_B is asserted. The MSB is the first bit of each word received on MOSI and the LSB is the last bit of each word received on MOSI. This pin has threshold level compatible input voltages allowing proper operation with microprocessors using a 3.3 V to 5.0 V (VDDQ) supply. CS_B Control word Configure words MOSI/ SCLK 31 30 29 28 27 26 25 24 23 22 21 20 ... 3 2 1 0 MISO INTflg Switch Status Register Fault Status SG/SP input status Figure 18. First SPI operation (after POR) CS_B CS_B Control word Next Control word Configure word Next Configure words MOSI/ SCLK MOSI/ SCLK 31 30 29 28 27 26 25 24 23 22 21 20 ... 3 2 MISO 1 0 31 30 29 28 27 26 25 24 23 22 21 20 ... 3 2 1 0 MISO Previous Address Previous command data Control Word Configure Word Figure 19. SPI write operation 33978 29 NXP Semiconductors CS_B CS_B Control word (READ) Next Control word DON'T CARE Next Configure words MOSI/ SCLK MOSI/ SCLK 31 30 29 28 27 26 25 24 23 22 21 20 ... 3 2 MISO 1 0 31 30 29 28 27 26 25 24 23 22 21 20 ... 3 2 1 0 MISO Previous Address Previous command data Control Word (READ) Register Data Figure 20. SPI read operation CSb SCLK DI DO 1 st IC CSb SCLK MISO MISI MCU CSb SCLK DI DO 2 nd IC CSb SCLK DI DO 3 rd IC CSb Don' t Care MOSI - 3 rd IC MOSI- 2 nd IC MOSI- 1 st IC MOSI - 1 st IC MCU MISO MISO - 1 st IC MOSI - 2 nd IC MISO - 2 st IC MOSI - 3 rd IC MISO - 3 rd IC MCU MOSI MISO - 3 rd IC MISO - 2 nd IC MISO - 1 st IC Don' t Care Figure 21. Daisy chain SPI operation 33978 NXP Semiconductors 30 7.10 SPI control register definition A 32-bit SPI allows the system microprocessor to configure the 33978 for each input as well as read out the status of each input. The SPI also allows the Fault Status and INTflg bits to be read via the SPI. The SPI MOSI bit definitions are given in Table 11: Table 11. MOSI input register bit definition Register # 0 Register name Address Rb/W SPI check 0 0 0 0 0 0 0 0 02/03 Device configuration register 0 0 0 0 0 0 1 0/1 04/05 Tri-state SP register 0 0 0 0 0 1 0 0/1 06/07 Tri-state SG register 0 0 0 0 0 1 1 0/1 08/09 Wetting current level SP register 0 0 0 0 1 0 0 0/1 0A/0B Wetting current level SG register 0 0 0 0 0 1 0 1 0/1 0C/0D Wetting current level SG register 1 0 0 0 0 1 1 0 0/1 16/17 Continuous wetting current SP register 0 0 0 1 0 1 1 0/1 18/19 Continuous Wetting Current SG Register 0 0 0 1 1 0 0 0/1 1A/1B Interrupt enable SP register 0 0 0 1 1 0 1 0/1 1C/1D Interrupt enable SG register 0 0 0 1 1 1 0 0/1 1E/1F Low-power mode configuration 0 0 0 1 1 1 1 0/1 20/21 Wake-up enable register SP 0 0 1 0 0 0 0 0/1 22/23 Wake-up enable register SG 0 0 1 0 0 0 1 0/1 24/25 Comparator only SP 0 0 1 0 0 1 0 0/1 26/27 Comparator only SG 0 0 1 0 0 1 1 0/1 28/29 LPM voltage threshold SP configuration 0 0 1 0 1 0 0 0/1 2A/2B LPM voltage threshold SG configuration 0 0 1 0 1 0 1 0/1 2C/2D Polling current SP configuration 0 0 1 0 1 1 0 0/1 2E/2F Polling current SG configuration 0 0 1 0 1 1 1 0/1 30/31 Slow polling SP 0 0 1 1 0 0 0 0/1 32/33 Slow polling SG 0 0 1 1 0 0 1 0/1 34/35 Wake-up debounce SP 0 0 1 1 0 1 0 0/1 36/37 Wake-up debounce SG 0 0 1 1 0 1 1 0/1 39 Enter low-power mode 0 0 1 1 1 0 0 1 3A/3B AMUX control register 0 0 1 1 1 0 1 0/1 3E Read switch status 0 0 1 1 1 1 1 0 42 Fault status register 0 1 0 0 0 0 1 0 47 Interrupt request 0 1 0 0 0 1 1 1 49 Reset register 0 1 0 0 1 0 0 1 The 32-bit SPI word consists of a command word (8-bit) and three configure words (24-bit). The 8 MSB bits are the command bits that select what type of configuration is to occur. The remaining 24-bits are used to select the inputs to be configured. * Bit 31 - 24 = Command word: Use to select what configuration is to occur (example: setting wake-up enable command) * Bit 23 - 0 = SGn input select word: Use these bits in conjunction with the command word to determine which input is setup. Configuration registers may be read or written to. To read the contents of a configuration register, send the register address + `0' on the LSB of the command word; the contents of the corresponding register will be shifted out of the MISO buffer in the next SPI cycle. When a Read command is sent, the answer (in the next SPI transaction) includes the Register address in the upper byte (see Figure 20). 33978 31 NXP Semiconductors Read example: * Send 0x0C00_0000 Receive: 8000_0000 (for example after a POR) * Send 0x0000_0000 Receive: 0C00_0000 (address + register data) The first response from the device after a POR event is a Read Status register (0x3Exxxxxx where x is the status of the inputs). This is the same for exiting the Low-power mode (see Figure 18.). To write into a configuration register, send the register Address + `1' on the LSB of the command word and the configuration data on the next 24 bits. The new value of the register will be shifted out of the MISO buffer in the next SPI cycle, along with the register address. Table 7.10.1 provides a general overview of the functional SPI commands and configuration bits. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 X X X X X X X X X X X X X X X X X X X X X X X X 0000001 0/1 FS INT X X X X X X X X aconfig1 0000000 Device Configuration X X X X X SP7 SPI check SP0 16 SP1 17 SP2 18 SP3 19 SP4 20 SP5 21 IntB_Out 24 R/W SP6 22 WAKE_B Pull up [31-25] Address aconfig0 23 VBATP OV Disable Commands SBPOLL TIME Table 12. Functional SPI register map Tri-State Enable SP 0000010 0/1 FS INT X X X X X X X X Tri-State Enable SG 0000011 0/1 FS INT X X X X X X X X Wetting Current Level SP 0000100 0/1 SP7[2-0] SP6[2-0] SP5[2-0] SP4[2-0] SP3[2-0] SP2[2-0] SP1[2-0] SP0[2-0] Wetting Current Level SG 0 0000101 0/1 SG7[2-0] SG6[2-0] SG5[2-0] SG4[2-0] SG3[2-0] SG2[2-0] SG1[2-0] SG0[2-0] Wetting Current Level SG 1 0000110 0/1 FS INT X X X X SG13[2-0] SG12[2-0] SG11[2-0] SG10[2-0] SG9[2-0] SG8[2-0] Continuous Wetting Current Enable SP 0001011 0/1 FS INT X X X X X X X X Continuous Wetting Current Enable SG 0001100 0/1 FS INT X X X X X X X X Interrupt Enable SP 0001101 0/1 FS INT X X X X X X X X Interrupt Enable SG 0001110 0/1 FS INT X X X X X X X X Low-power mode configuration 0001111 0/1 FS INT X X X X X X X X Wake-Up Enable SP 0010000 0/1 FS INT X X X X X X X X Wake-Up Enable SG 0010001 0/1 FS INT X X X X X X X X LPM Comparator Only SP 0010010 0/1 FS INT X X X X X X X X LPM Comparator Only SG 0010011 0/1 FS INT X X X X X X X X LPM Voltage Threshold SP 0010100 0/1 FS INT X X X X X X X X LPM Voltage Threshold SG 0010101 0/1 FS INT X X X X X X X X LPM Polling current config SP 0010110 0/1 FS INT X X X X X X X X LPM Polling current config SG 0010111 0/1 FS INT X X X X X X X X LPM Slow Polling SP 0011000 0/1 FS INT X X X X X X X X LPM Slow Polling SG 0011001 0/1 FS INT X X X X X X X X Wake-Up Debounce SP 0011010 0/1 FS INT X X X X X X X X Wake-Up Debounce SG 0011011 0/1 FS INT X X X X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SG13 SG12 SG11 SG10 SG9 X X X X X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X int3 int2 int2 int0 poll3 poll2 poll1 poll0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X X X X X X X X X X X X X X X X X X X X X X X X X X X Read Switch Status 0011111 0 SP1 SP0 SG13 SG12 SG11 SG10 SG9 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 Fault Status 0100001 0 X X X X X SPI Error hash fault X UV OV TempFlag OT INT_B wake WAKE_B SpiWake POR X X X X X X INT SP2 X INT FS X X FS 0/1 SP3 X 1 0011101 X X 0011100 SP4 X Enter Low-power mode AMUX Channel Select SPI X SP0 SG0 SP5 SP1 SG1 X SP2 SG2 SP6 SP3 SG3 X SP4 SG4 SP7 SP5 SG5 X SP6 SG6 INTflg SP7 SG7 INTflg X SG8 FAULT STATUS SG13 SG12 SG11 SG10 SG9 X SG8 Interrupt Pulse Request 0100011 1 FS INT X X X X X X X X X X X X X X X X X X X X X X Reset 0100100 1 X X X X X X X X X X X X X X X X X X X X X X X X asett asel5 asel4 asel3 asel2 asel1 asel0 Notes 28. FS = FAULT STATUS (available for reading on MISO return word) 29. INT = INTflg (available for reading on MISO return word) 33978 NXP Semiconductors 32 7.10.1 SPI check The MCU may check the communication with the IC by using the SPI Check register. The MCU sends the command and the response during the next SPI transaction will be 0x123456. The SPI Check command does not return Fault Status or INTflg bit, thus interrupts will not be cleared. Table 13. SPI check command Register address R SPI data bits [23 - 0] [31-25] [24] bits [23 - 16] 0000_000 0 0000_0000 bits [15 - 8] 0000_0000 bits [7 - 0] 0000_0000 MISO return word 7.10.2 0x00123456 Device configuration register The device has various configuration settings that are global in nature. The configuration settings are as follows: * When the 33978 is in the overvoltage region, a Logic [0] on the VBATP OV bit limits the wetting current on all input channels to 2 mA and the 33978 will not be able to enter into the Low-power mode. A Logic [1] allows the device to operate normally even in the overvoltage region. The OV flag will be set when the device enters in the OV region, regardless the value of the VBATP OV bit. * WAKE_B can be used to enable an external power supply regulator to supply the VDDQ voltage rail. When the WAKE_B VDDQ check bit is a Logic [0], the WAKE_B pin is expected to be pulled-up internally or externally to VDDQ and VDDQ is expected to go low, therefore the 33978 does not wake-up on the falling edge of WAKE_B. A Logic [1], assumes the user is using an external pull-up to VBATP or VDDQ (when VDDQ is not expected to be off) and the IC wakes up on a falling edge of WAKE_B. * INT_B out is used to select how the INT_B pin operates when an interrupt occurs. The IC is able to pulse low [1] or latch low [0]. * Aconfig[1-0] is used to determine the method of selecting the AMUX output, either a SPI command or using a hardwired setup using SG[3-1]. * Inputs SP0-7 may be programmable for switch-to-battery or switch-to-ground. These inputs types are defined using the settings command. To set a SPn input for switch-to-battery, a logic [1] for the appropriate bit must be set. To set a SPn input for switch-toground, a logic [0] for the appropriate bit must be set. The MCU may change or update the programmable switch register via software at any time in Normal mode. Regardless of the setting, when the SPn input switch is closed a logic [1] is placed in the serial output response register. 33978 33 NXP Semiconductors Table 14. Device configuration register Register address R/W [31-25] [24] 0000_001 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SBPOLL TIME VBATP OV disable WAKE_B VDDQ Check INT_B out Aconfig1 Aconfig0 Unused 0 0 0 0 1 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0000_001[R/W] FAULT STATUS INTflg Register Data Default on POR SP0 1 Table 15. Device configuration bits definition Bit Functions Default value Description 23-14 Unused 0 Unused 13 SBPOLLTIME 0 Select the polling time for SP channels configured as SB. * A logic [0] set the active polling timer to 1ms, * A logic [1] sets the active polling timer to 55 s. 12 VBATP OV Disable 0 VBATP Overvoltage protection * 0 - Enabled * 1 - Disable 11 WAKE_B VDDQ Check 1 Enable/Disable WAKE_B to wake-up the device on falling edge when VDDQ is not present. * 0 - WAKE_B is pulled up to VDDQ (internally and/or externally). WAKE_B is ignored while in LPM if VDDQ is low. * 1 - WAKE_B is externally pulled up to VBATP or VDDQ and wakes upon a falling edge of the WAKE_B pin regardless of the VDDQ status.(VDDQ is not expected to go low) 10 Int_B_Out 0 Interrupt pin behavior * 0 - INT pin stays low when interrupt occurs * 1 - INT pin pulse low and return high Configure the AMUX output control method * 00 - SPI (default) * 01 - SPI * 10 - HW 2bit * 11 - HW 3bit Refer to section 7.8, "AMUX functional block" for details on 2 and 3 bit hardwire configuration. 9-8 Aconfig(1-0) 00 7-0 SP7 - SP0 1111_1111 Configure the SP pin as Switch to Battery (SB) or Switch to ground (SG) * 0 - Switch to Ground * 1 - Switch to Battery 33978 NXP Semiconductors 34 7.10.3 Tri-state SP register The tri-state command is use to set the input nodes as high-impedance (Table 16). By setting the tri-state register bit to logic [1], the input is high-impedance regardless of the Wetting current setting. The configurable comparator (4.0 V default) on each input remains active. The MCU may change or update the tri-state register via software at any time in Normal mode. The tri-state register defaults to 1 (inputs are tri-stated). Any inputs in tri-state is still polled in LPM but the current source is not active during this time. The determination of change of state occurs at the end of the tACTIVEPOLL and the wake-up decision is made. Table 16. Tri-state SP register Register address R/W [31-25] [24] 0000_010 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0000_010[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.4 Tri-state SG register The tri-state command is used to set the input nodes as high-impedance (Table 17). By setting the tri-state register bit to logic [1], the input is high-impedance regardless of the Wetting command setting. The configurable comparator (4.0 V default) on each input remains active. The MCU may change or update the tri-state register via software at any time in Normal mode. The tri-state register defaults to 1 (inputs are tri-stated. Any inputs in tri-state is still polled in LPM but the current source is not active during this time. The determination of change of state occurs at the end of the tACTIVEPOLL and the wake-up decision is made. Table 17. Tri-state SG register Register address R/W [31-25] [24] 0000_011 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 1 1 1 1 1 1 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0000_011[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 35 NXP Semiconductors 7.10.5 Wetting current level SP register The IC contains configurable wetting currents (Default = 16 mA). Three bits are used to control each individual input pin with the values set in Table 18. The MCU may change or update the wetting current register via software at any time in Normal mode. Table 18. Wetting current level SP register Register address R/W [31-25] [24] bit [23 - 21] bit [20 - 18] bit [17 - 16] 0000_100 0/1 SP7 [2-0] SP6[2-0] SP5[2-1] 110 110 11 Default on POR SPI data bits [23 - 0] bit [15] bit [14 - 12] bit [11 - 9] bit [8] SP5[0] SP4 [2-0] SP3[2-0] SP2[2] 0 110 110 1 bit [7 - 6] bit [5 - 3] bit [2 - 0] SP2[1-0] SP1[2-0] SP0[2-0] 10 110 110 MISO return word bits [23 - 0] 0000_100[R/W] Register Data See Table 21 for the selectable Wetting Current level values for both SPx and SGx pins. 7.10.6 Wetting current level SG register 0 The IC contains configurable wetting currents (Default = 16 mA). Three bits are used to control each individual input pin with the values set in Table 19. The MCU may change or update the wetting current register via software at any time in Normal mode. Table 19. Wetting current level SG register 0 Register address R/W [31-25] [24] bit [23 - 21] bit [20 - 18] bit [17 - 16] 0000_101 0/1 SG7 [2-0] SG6[2-0] SG5[2-1] 110 110 11 Default on POR SPI data bits [23 - 0] bit [15] bit [14 - 12] bit [11 - 9] bit [8] SG5[0] SG4 [2-0] SG3[2-0] SG2[2] 0 110 110 1 bit [7 - 6] bit [5 - 3] bit [2 - 0] SG2[1-0] SG1[2-0] SG0[2-0] 10 110 110 MISO return word bits [23 - 0] 0000_101[R/W] Register Data See Table 21 for the selectable Wetting Current level values for both SPx and SGx pins. 33978 NXP Semiconductors 36 7.10.7 Wetting current level SG register 1 The IC contains configurable wetting currents (Default = 16 mA). Three bits are used to control each individual input pin with the values set in Table 20. The MCU may change or update the wetting current register via software at any time in Normal mode. Table 20. Wetting current level SG register 1 Register address R/W [31-25] [24] 0000_110 0/1 Default on POR SPI data bits [23 - 0] bit [23 - 21] bit [20 - 18] bit [17 - 16] Unused SG13[2-1] 0 11 bit [15] bit [14 - 12] bit [11 - 9] bit [8] SG13[0] SG12 [2-0] SG11[2-0] SG10[2] 0 110 110 1 bit [7 - 6] bit [5 - 3] bit [2 - 0] SG10[1-0] SG9[2-0] SG8[2-0] 10 110 110 MISO return word bits [23 - 0] 0000_110[R/W] Register Data See Table 21 for the selectable Wetting Current level values for both SPx and SGx pins. Table 21. SPx/SGx selectable wetting current levels SPx/SGx[2-0] Wetting Current Level bit 2 bit 1 bit 0 0 0 0 2.0 mA 0 0 1 6.0 mA 0 1 0 8.0 mA 0 1 1 10 mA 1 0 0 12 mA 1 0 1 14 mA 1 1 0 16 mA 1 1 1 20 mA 33978 37 NXP Semiconductors 7.10.8 Continuous wetting current SP register Each switch input has a designated 20 ms timer. The timer starts when the specific switch input crosses the comparator threshold. When the 20 ms timer expires, the contact current is reduced from the configured wetting current (16 mA) to the Sustain current. The wetting current is defined to be an elevated level that reduces to the lower sustain current level after the timer has expired. With multiple wetting current timers disabled, power dissipation for the IC must be considered. The MCU may change or update the continuos wetting current register via software at any time in Normal mode. This allows the MCU to control the amount of time wetting current is applied to the switch contact. Programming the continuos wetting current bit to logic [0] operates normally with a higher wetting current followed by sustain current after 20 ms (pulsed Wetting current operation). Programming to logic [1] enables the continuous wetting current (Table 22) and results in a full time wetting current level. The continuous wetting current register defaults to 0 (pulse wetting current operation). Table 22. Continuous wetting current SP register Register address R/W [31-25] [24] 0001_011 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0001_011[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.9 Continuous Wetting Current SG Register Each switch input has a designated 20 ms timer. The timer starts when the specific switch input crosses the comparator threshold. When the 20 ms timer expires, the contact current is reduced from the configured wetting current (16 mA) to 2.0 mA. The wetting current is defined to be at an elevated level that reduces to the lower sustain current level after the timer has expired. With multiple wetting current timers disabled, power dissipation for the IC must be considered. The MCU may change or update the continuous wetting current register via software at any time in Normal mode. This allows the MCU to control the amount of time wetting current is applied to the switch contact. Programming the continuos wetting current bit to logic [0] operates normally with a higher wetting current followed by sustain current after 20 ms (Pulse wetting current operation). Programming to logic [1] enables the continuous wetting current (Table 23) and results in a full time wetting current level. The continuous wetting current register defaults to 0 (pulse wetting current operation). 33978 NXP Semiconductors 38 Table 23. Continuous wetting current SG register Register address R/W [31-25] [24] 0001_100 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0001_100[R/W] FAULT STATUS INTflg Register Data Default on POR Switch to Ground Closed Switch to Ground open IWET Continuous wetting current enabled 0 ma IWET Continuous wetting current disabled ISUS=~2mA 0 ma 20 ms Figure 22. Pulsed/continuous wetting current configuration 33978 39 NXP Semiconductors 7.10.10 Interrupt enable SP register The interrupt register defines the inputs that are allowed to Interrupt the 33978 Normal mode. Programming the interrupt bit to logic [0] disables the specific input from generating an interrupt. Programming the interrupt bit to logic [1] enables the specific input to generate an interrupt with switch change of state The MCU may change or update the interrupt register via software at any time in Normal mode. The Interrupt register defaults to logic [1] (Interrupt enabled). Table 24. Interrupt enable SP register Register address R/W [31-25] [24] 0001_101 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0001_101[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.11 Interrupt enable SG register The interrupt register defines the inputs that are allowed to Interrupt the 33978 Normal mode. Programming the interrupt bit to logic [0] disables the specific input from generating an interrupt. Programming the interrupt bit to logic [1] enables the specific input to generate an interrupt with switch change of state The MCU may change or update the interrupt register via software at any time in Normal mode. The Interrupt register defaults to logic [1] (Interrupt enabled). Table 25. Interrupt enable SG register Register address R/W [31-25] [24] 0001_110 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 1 1 1 1 1 1 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0001_110[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 NXP Semiconductors 40 7.10.12 Low-power mode configuration The device has various configuration settings for the Low-power mode operation. The configuration settings are as follows: int[3-0] is used to set the interrupt timer value. With the interrupt timer set, the IC wakes up after the selected timer expires and issue an interrupt. This register can be selected to be OFF such that the IC does not wake-up from an interrupt timer. poll[3-0] is used to set the normal polling rate for the IC. The polling rate is the time between polling events. The current sources become active at this time for a time of tACTIVESGPOLLING or tACTIVESBPOLLING for SG or SB channels respectively. Table 26. Low-power mode configuration register Register address R/W [31-25] [24] 0001_111 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 int3 int2 int1 int0 poll3 poll2 poll1 poll0 0 0 0 0 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0001_111[R/W] FAULT STATUS INTflg Register Data Default on POR Table 27. Low-power mode configuration bits definition Bit Functions Default value 23 - 8 Unused 0 Description Unused Set the Interrupt timer value 7-4 int[3-0] 0000 * * * * * * * * 0000 - OFF 0001 - 6.0 ms 0010 - 12 ms 0011 - 24 ms 0100 - 48 ms 0101 - 96 ms 0110 - 192 ms 0111 - 394 ms * * * * * * * * 1000 - 4.0 ms 1001 - 8.0 ms 1010 - 16 ms 1011 - 32 ms 1100 - 64 ms 1101 - 128 ms 1110 - 256 ms 1111 - 512 ms * * * * * * * * 1000 - 32 ms 1001 - 36 ms 1010 - 40 ms 1011 - 44 ms 1100 - 52 ms 1101 - 56 ms 1110 - 60 ms 1111 - 64 ms (default) Set the polling rate for switch detection 3-0 poll[3-0] 1111 * * * * * * * * 0000 - 3.0 ms 0001 - 6.0 ms 0010 - 12 ms 0011 - 24 ms 0100 - 48 ms 0101 - 68 ms 0110 - 76 ms 0111 - 128 ms 33978 41 NXP Semiconductors 7.10.13 Wake-up enable register SP The wake-up register defines the inputs that are allowed to wake the 33978 from Low-power mode. Programming the wake-up bit to logic [0] disables the specific input from waking the IC (Table 28). Programming the wake-up bit to logic [1] enables the specific input to wake-up with switch change of state The MCU may change or update the wake-up register via software at any time in Normal mode. The Wake-up register defaults to logic [1] (wake-up enabled). If all channels (SG and SB) have the Wake-up bit disabled, the device disables the polling timer to reduce the current consumption during Low-power mode. Table 28. Wake-up enable SP register Register address R/W [31-25] [24] 0010_000 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0010_000[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.14 Wake-up enable register SG The wake-up register defines the inputs that are allowed to wake the 33978 from Low-power mode. Programming the wake-up bit to logic [0] disables the specific input from waking the IC (Table 29). Programming the wake-up bit to logic [1] enables the specific input to wake-up with any switch change of state The MCU may change or update the wake-up register via software at any time in Normal mode. The Wake-up register defaults to logic [1] (wake-up enabled). If all channels (SG and SB) have the Wake-up bit disabled, the device disables the polling timer to reduce the current consumption during Low-power mode. Table 29. Wake-up enable SG register Register address R/W [31-25] [24] 0010_001 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 1 1 1 1 1 1 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 1 1 1 1 1 1 1 1 MISO return word bit [23] bit [22] bits [21 - 0] 0010_001[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 NXP Semiconductors 42 7.10.15 Comparator only SP The comparator only register allows the input comparators to be active during LPM with no polling current. In this case, the inputs can receive a digital signal on the order of the LPM clock cycle and wake-up on a change of state. This register is intended to be used for signals that are driven by an external chip and drive to 5.0 V. Table 30. Comparator only SP Register Register address R/W [31-25] [24] 0010_010 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0010_010[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.16 Comparator only SG The comparator only register allows the input comparators to be active during LPM with no polling current. In this case, the inputs can receive a digital signal on the order of the LPM clock cycle and wake-up on a change of state. This register is intended to be used for signals that are driven by an external chip and drive to 5.0 V. Table 31. Comparator only SG register Register address R/W [31-25] [24] 0010_011 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0010_011[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 43 NXP Semiconductors 7.10.17 LPM voltage threshold SP configuration The 33978 is able to use different voltage thresholds to wake-up from LPM. When configured as SG, a Logic [0] means the input will use the LPM delta voltage threshold to determine the state of the switch. A Logic [1] means the input uses the Normal threshold (VICTHR) to determine the state of the switch. When configured as an SB, it only uses the 4.0 V threshold regardless the status of the LPM voltage threshold bit. The user must ensure that the correct current level is set to allow the crossing of the normal mode threshold (typ. 4.0 V) Table 32. LPM voltage threshold configuration SP register Register address R/W [31-25] [24] 0010_100 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0010_100[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.18 LPM voltage threshold SG configuration This means the input uses the LPM delta voltage threshold to determine the state of the switch. A Logic [1] means the input uses the Normal threshold to determine the state of the switch. The user must ensure that the correct current level is set to allow the crossing of the normal mode threshold (typ. 4.0 V) Table 33. LPM voltage threshold configuration SG register Register address R/W [31-25] [24] 0010_101 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0010_101[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 NXP Semiconductors 44 7.10.19 Polling current SP configuration The normal polling current for LPM is 2.2 mA for SB channels and 1.0 mA for SG channels, A logic [0] selects the normal polling current for each individual channel. The user may choose to select the IWET current value as defined in the wetting current level registers by writing a Logic [1] on this bit; this will result in higher LPM currents but may be used in cases when a higher polling current is needed. Table 34. Polling current configuration SP register Register address R/W [31-25] [24] 0010_110 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0010_110[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.20 Polling current SG configuration A Logic [0] selects the normal polling current for LPM =1.0 mA. The user may choose to select the IWET current value as defined in the wetting current registers for LPM by writing a Logic [1] in this bit; this results in higher LPM currents but may be used in cases when a higher polling current is needed. Table 35. Polling current configuration SG register Register address R/W [31-25] [24] 0010_111 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0010_111[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 45 NXP Semiconductors 7.10.21 Slow polling SP The normal polling rate is defined in the Low-power mode configuration register. If the user is able to poll at a slower rate (4x) the LPM current level decreases significantly. Setting the bit to [0] results in the input polling at the normal rate as selected. Setting the bit to [1] results in the input being polled at a slower frequency at 4x the normal rate. Table 36. Slow polling SP Register Register Address R/W [31-25] [24] 0011_000 0/1 SPI Data Bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 0 0 0 0 0 0 MISO Return Word bit [23] bit [22] bits [21 - 0] 0011_000[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.22 Slow polling SG The normal polling rate is defined in the Low-power mode configuration register. If the user is able to poll at a slower rate (4x) the LPM current level decreases significantly. Setting the bit to [0] results in the input polling at the normal rate as selected. Setting the bit to [1] results in the input being polled at a slower frequency at 4x the normal rate. Table 37. Slow Polling SG Register Register address R/W [31-25] [24] 0011_001 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0011_001[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 NXP Semiconductors 46 7.10.23 Wake-up debounce SP The IC is able to extend the time that the active polling takes place to ensure that a true change of state has occurred in LPM and reduce the chance that noise has impacted the measurement. If this bit is [0], the IC uses a voltage difference technique to determine if a switch has changed sate. If this bit is set [1], the IC debounces the measurement by continuing to source the LPM polling current for an additional 1.2 ms and take the measurement based on the final voltage level. This helps to ensure that the switch is detected correctly in noisy systems. Table 38. Wake-up debounce SP register Register address R/W [31-25] [24] 0011_010 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0011_010[R/W] FAULT STATUS INTflg Register Data Default on POR 7.10.24 Wake-up debounce SG The IC is able to extend the time that the active polling takes place to ensure that a true change of state has occurred in LPM and reduce the chance that noise has impacted the measurement. If this bit is [0], the IC uses a voltage difference technique to determine if a switch has changed sate. If this bit is set [1], the IC debounces the measurement by continuing to source the LPM polling current for an additional 1.2 ms and take the measurement based on the final voltage level. This helps to ensure that the switch is detected correctly in noisy systems. Table 39. Slow polling SG Register Register address R/W [31-25] [24] 0011_011 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SG13 SG12 SG11 SG10 SG9 SG8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 0 0 0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0011_011[R/W] FAULT STATUS INTflg Register Data Default on POR 33978 47 NXP Semiconductors 7.10.25 Enter low-power mode Low-power mode (LPM) is used to reduce system quiescent currents. Low-power mode may be entered only by sending the Low-power command. When returning to Normal mode, all register settings is maintained. The Enter Low-power mode register is write only and has the effect of going to LPM and beginning operation as selected (polling, interrupt timer). When returning form Low-power mode, the first SPI transaction will return the Fault Status and the intflg bit set to high, as well as the actual status of the Input pins. Table 40. Enter low-power mode command Register address W SPI data bits [23 - 0] [31-25] [24] bits [23 - 16] 0011_100 1 0000_0000 bits [15 - 8] 0000_0000 bits [7 - 0] 0000_0000 MISO return word - 7.10.26 AMUX control register The analog voltage on switch inputs may be read by the MCU using the analog command (Table 41). Internal to the33978 is a 24-to-1 analog multiplexer. The voltage present on the selected input pin is buffered and made available on the AMUX output pin. The AMUX output pin is clamped to a maximum of VDDQ volts regardless of the higher voltages present on the input pin. After an input has been selected as the analog, the corresponding bit in the next MISO data stream is logic [0]. Setting the current to wetting current (configurable) may be useful for reading sensor inputs. The MCU may change or update the analog select register via software at any time in Normal mode. The analog select defaults to no input. Table 41. Slow polling SG register Register address R/W [31-25] [24] 0011_101 0/1 SPI data bits [23 - 0] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 Unused 0 0 0 0 0 0 0 0 bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 Unused 0 0 0 0 0 0 0 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Unused asett0 0 0 0 0 0 MISO return word bit [23] bit [22] bits [21 - 0] 0011_101[R/W] FAULT STATUS INTflg Register Data Default on POR asel[5-0] 0 0 0 Table 42. AMUX current select asett[0] Zsource 0 hi Z (default) 1 IWET 33978 NXP Semiconductors 48 Table 43. AMUX channel select asel 5 asel 4 asel3 asel 2 asel 1 asel 0 Analog channel select 0 0 0 0 0 0 No Input Selected 0 0 0 0 0 1 SG0 0 0 0 0 1 0 SG1 0 0 0 0 1 1 SG2 0 0 0 1 0 0 SG3 0 0 0 1 0 1 SG4 0 0 0 1 1 0 SG5 0 0 0 1 1 1 SG6 0 0 1 0 0 0 SG7 0 0 1 0 0 1 SG8 0 0 1 0 1 0 SG9 0 0 1 0 1 1 SG10 0 0 1 1 0 0 SG11 0 0 1 1 0 1 SG12 0 0 1 1 1 0 SG13 0 0 1 1 1 1 SP0 0 1 0 0 0 0 SP1 0 1 0 0 0 1 SP2 0 1 0 0 1 0 SP3 0 1 0 0 1 1 SP4 0 1 0 1 0 0 SP5 0 1 0 1 0 1 SP6 0 1 0 1 1 0 SP7 0 1 0 1 1 1 Temp Diode 0 1 1 0 0 0 Battery Sense 7.10.27 Read switch status The Read switch status register is used to determine the state of each of the inputs and is read only. All of the inputs (SGn and SPn) are returned after the next command is sent. A Logic [1] means the switch is closed while a Logic [0] is an open switch. Included in the status register are two more bits, the Fault Status bit and intflg bit. The Fault Status bit is a combination of the extended status bits and the wetting current fault bits. If any of these bits are set, the Fault Status bit is set. The intflg bit is set when an interrupt occurs on this device. After POR, both the Fault Status bit and the intflg bit are set high to indicate an interrupt due to a POR occurred. The intflg bit will be cleared upon reading the Read Switch Status register, and the Fault Status bit will remain high until the Fault status register is read and thus the POR fault bit and all other fault flags are cleared. The Fault Status and Intflg bits are semi-global flags, if a fault or an interrupt occurs, these bit will be returned after writing or reading any command, except for the SPICheck and the Wetting Current configuration registers, which use those bits to set/display the device configuration. 33978 49 NXP Semiconductors Table 44. Read switch status command Register address R SPI data bits [23 - 0] [31-25] [24] bit 23 bit 22 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 0011_111 0 FAULT STATUS INTflg SP7 SP6 SP5 SP4 SP3 SP2 1 1 X X X X X X bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 SP1 SP0 SG13 SG12 SG11 SG10 SG9 SG8 X X X X X X X X bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0 X X X X X X X X MISO return word bit [23] bit [22] bits [21-14] bits [13-0] 0011_1110 FAULT STATUS INTflg SP7 -SP0 Switch Status SG13 - SG0 Switch Status Default After POR The fault/status diagnostic capability consists of one internal 24 bit register. The content of the fault/status register is shown in Table 45. Bits 0 - 21 shows the status of each input where logic [1] is a closed switch and logic [0] is an open switch. In addition to input status information, Fault status such as die over-temp, Hash fault, SPI errors, as well as interrupts are reported. A SPI read cycle is initiated by a CS_B logic `1' to `0' transition, followed by 32 SCLK cycles to shift the fault / status registers out the MISO pin. The INT_B pin is cleared 1.0 ms after the falling edge of CS_B. The fault is immediately set again if the fault condition is still present. The Fault Status bit sets any time a Fault occurs, and the Fault register (Table 46) must be read in order to clear the Fault status flag. The intflg bit sets any time an interrupt event occurs (change of state on switch, any fault status bit gets set). Any SPI message that will return intflg bit will clear this flag (even if the event is still occurring, for example an overtemp, will cause an interrupt. The interrupt can be cleared but the chip will not interrupt again based on the overtemp until that fault has gone away). SG0 SG1 SG2 SG3 SG4 SG5 SG6 SG7 SG8 SG9 SG10 SG11 SG12 SG13 SP0 SP1 SP2 SP3 SP4 SP5 SP6 SP7 INTflg MISO Response Sends Fault Status Table 45. MISO output register definition Bit 23 : Fault Status: * 0 = No Fault * 1 = Indicates a fault has occurred and should be viewed in the fault status register. Bit 22 : Intflg: * 0 = No Change of state * 1 = Change of state detected. Bit 21 - 0 : SPx /SGx input status: * 0 = Open switch; * 1 =Closed switch 33978 NXP Semiconductors 50 7.10.28 Fault status register To read the fault status bits the user should first sent a message to the IC with the fault status register address followed by any given second command. The MISO response from the second command will contain the fault flags information. Table 46. Fault status register Register address R SPI data bits [23 - 0] [31-25] [24] bit 23 bit 22 0100_001 0 Unused INTflg 0 1 0 0 bit 15 bit 14 bit 13 bit 12 bit 21 bit 20 bit 19 bit 18 bit 17 bit 16 0 0 0 0 bit 11 bit 10 bit 9 bit 8 SPI error Hash Fault Unused Unused Unused 0 0 0 0 0 X X 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 UV OV TempFlag OT INT_B Wake WAKE_B Wake SPI Wake POR X X X X X X X X MISO return word bit [23] bit [22] bits [21-0] 0100_0010 FAULT STATUS INTflg FAULT/FLAG BITS Default After POR Table 47. MISO response for fault status command Bit Functions Default value Description 23 Unused 0 Unused 22 INTflg X Reports that an Interrupt has occurred, user should read the status register to determine cause. * Set: Various (SGx change of state, SPx change of state, Extended status bits). * Reset: Clear of fault or read of Status register 21-11 Unused 0 Unused 10 SPI error X Any SPI error generates a bit (Wrong address, incorrect modulo). * Set: SPI message error. * Reset: Read fault status register and no SPI errors. 9 Hash Fault X SPI register and hash mismatch. * Set: Mismatch between SPI registers and hash. * Reset: No mismatch and SPI flag read. 8 Unused 0 Unused 7 UV X Reports that low VBATP voltage was in undervoltage range * Set: Voltage drops below UV level. * Reset: VBATP rises above UV level and flag read (SPI) 6 OV X Report that the voltage on VBATP was higher than OV threshold * Set: Voltage at VBATP rises above overvoltage threshold. * Reset: Overvoltage condition is over and flag read (SPI) 5 Temp Flag X Temperature warning to note elevated IC temperature * Set: tLIM warning threshold is passed. * Reset: Temperature drops below thermal warning threshold + hysteresis and flag read (SPI) 4 OT X Tlim event occurred on the IC * Set: Tlim warning threshold is passed. * Reset: Temperature drops below thermal warning threshold + hysteresis and flag read (SPI) 33978 51 NXP Semiconductors Table 47. MISO response for fault status command (continued) 3 INT_B Wake X Part awakens via an external INT_B falling edge * Set: INT_B Wakes the part from LPM (external falling edge) * Reset: flag read (SPI). 2 WAKE_B Wake X Part awakens via an external WAKE_B falling edge * Set: External WAKE_B falling edge seen * Reset: flag read (SPI). 1 SPI Wake X Part awaken via a SPI message * Set: SPI message wakes the IC from LPM * Reset: flag read (SPI). 0 POR X Reports a POR event occurred. * Set: Voltage at VBATP pin dropped below VBATP(POR) voltage * Reset: flag read (SPI) 7.10.29 Interrupt request The MCU may request an Interrupt pulse of duration 100 s by sending the Interrupt request command. After an Interrupt request commands, the 33978 returns the Interrupt request command word, as well as the Fault status and INTflg bits set if a fault/interrupt event occurred. Sending an interrupt request command does not set the INTflg bit itself. Table 48. Interrupt request command Register address W SPI data bits [23 - 0] [31-25] [24] bits [23 - 16] 0100_011 1 0000_0000 bits [15 - 8] 0000_0000 bits [7 - 0] 0000_0000 MISO return word bit [23] bit [22] bits [21-0] 0100_0111 FAULT STATUS INTflg 0 7.10.30 Reset register Writing to this register causes all of the SPI registers to reset. Table 49. Reset command Register address W SPI data bits [23 - 0] [31-25] [24] bits [23 - 16] 0100_100 1 0000_0000 bits [15 - 8] 0000_0000 bits [7 - 0] 0000_0000 MISO return word bit [23] bit [22] bits [21-0] 0011_1110 FAULT STATUS INTflg Switch Status 33978 NXP Semiconductors 52 8 Typical applications 8.1 Application diagram Figure 23. Typical application diagram 8.2 Bill of materials Table 50. Bill of materials Item Quantity Reference Value Description 1 24 C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C25, C27 0.1 F CAP CER 0.1 uF 100 V X7R 10 % 0603 2 2 C23,C24 1.0 nF CAP CER 1000 PF 100 V 10 % X7R 0603 3 1 C26 100 F CAP ALEL 100 F 50 V 20 % -- SMD 4 1 D1 - 5 22 R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22 100 RES MF 100 0.5 W 1% 0805 6 1 R23 10 k RES MF 10 k 0.5 W 5 % 0805 (optional) 7 1 R25 10 k RES MF 10 k 0.5 W 5 % 0805 8 1 R24 1.0 k RES MF 1 k 0.5 W 5 % 0805 9 1 U1 MC33978 DIODE RECT 3.0 A 50 V AEC-Q101 SMB IC MULTIPLE DETECTION SWITCH INTERFACE SOIC32 33978 53 NXP Semiconductors 8.3 Abnormal operation The 33978 could be subject to various conditions considered abnormal as defined within this section. 8.3.1 Reverse battery This device with applicable external components will not be damaged by exposure to reverse battery conditions of -14 V. This test is performed for a period of one minute at 25 C. In addition, this negative voltage condition does not force any of the logic level I/O pins to a negative voltage less than -0.6 V at 10 mA or to a positive voltage greater the 5.0 V. This insures protection of the digital device interfacing with this device. 8.3.2 Ground offset The applicable driver outputs and/or current sense inputs are capable of operation with a ground offset of 1.0 V. The device will not be damaged by exposure to this condition and will maintain specified functionality. 8.3.3 Shorts to ground All I/Os of the device that are available at the module connector are protected against shorts to ground with maximum ground offset considered (i.e. -1.0 V referenced to device ground or other application specific value). The device will not be damaged by this condition. 8.3.4 Shorts to battery All I/Os of the device that are available at the module connector are protected against a short to battery (voltage value is application dependent, there may be cases where short to jump start or load dump voltage values are required). The device will not be damaged by this condition. 8.3.5 Unpowered shorts to battery All I/Os of the device that are available at the module connector are protected against unpowered (battery to the module is open) shorts to battery per application specifics. The device will not be damaged by this condition, will not enable any outputs nor backfeed onto the power rails (VBATP, VDDQ) or the digital I/O pins. 8.3.6 Loss of module ground The definition of a loss of ground condition at the device level is that all pins of the IC detects very low-impedance to battery. The nomenclature is suited to a test environment. In the application, a loss of ground condition results in all I/O pins floating to battery voltage, while all externally referenced I/O pins are at worst case pulled to ground. All applicable driver outputs and current sense inputs are protected against excessive leakage current due to loads that are referenced to an external ground (high-side drivers). 8.3.7 Loss of module battery The loss of battery condition at the parts level is that the power input pins of the IC see infinite impedance to the battery supply voltage (depending upon the application) but there is some undefined impedance looking from these pins to ground. All applicable driver outputs and current sense inputs are protected against excessive leakage current due to loads that are referenced to an external battery connection (low-side drivers). 33978 NXP Semiconductors 54 9 Packaging 9.1 Package mechanical dimensions Package dimensions are provided in package drawings. To find the most current package outline drawing, go to www.nxp.com and perform a keyword search for the drawing's document number. Table 51. Packaging information Package Suffix Package outline drawing number 32-Pin SOICW-EP EK 98ASA10556D 32-Pin QFN (WF-type) ES 98ASA00656D 33978 55 NXP Semiconductors 33978 NXP Semiconductors 56 33978 57 NXP Semiconductors 33978 NXP Semiconductors 58 33978 59 NXP Semiconductors 33978 NXP Semiconductors 60 33978 61 NXP Semiconductors 10 Reference section Table 52. 33978 reference documents Reference Description CDF-AEC-Q100 Stress Test Qualification For Automotive Grade Integrated Circuits Q-1000 Qualification Specification for Integrated Circuits SQ-1001 Specification Conformance ISO 7637 Electrical Disturbances from Conduction and Coupling ISO 61000 Electromagnetic Compatibility 33978 NXP Semiconductors 62 11 Revision history Revision Date Description of changes 1.0 3/2014 * Initial release 2.0 3/2014 * Removed Z from part numbers PCZ33978EK and PCZ33978ES in the Orderable part variations table * Major formatting and information arrangement * Updated Figure 1, 33978 simplified application diagram, removed CS_B pull-up resistor, not needed. * Added Industrial Part numbers MC34978EK and MC34978ES to Table 1 * Table 3 Clarified Switch Input Range specification (not a differential voltage between inputs and VBATP) * Table 3 Reduced Human Body Model (HBM) (VBATP versus GND) to 2500 V * Table 3 VESD6-2 Series resistor corrected to 50 , Added missing CZAP and RZAP conditions * Table 4 Updated Thermal Resistance specification * Added Figure 10, Functional block diagram * Added Figure 11, Battery voltage range * Added Figure 5, Glitch filter and interrupt delay timers and Figure 6, Interrupt pulse timer * Updated POR minimum specification to 2.7 V (previous 2.9 V) * Updated VBATP Normal mode maximum supply current to 12 mA (previous 8.0 mA) * Updated VDDQ undervoltage threshold maximum to 2.8 V (previous 2.7 V) * Updated sustain current at low battery to 2.4 mA (previous 2.0 mA) * Added a specification to cover the Normal mode switch detection threshold hysteresis. * Updated minimum limit on Switch detection threshold in LPM to 80 mV * Updated minimum ratio for switch threshold at low battery to 0.55x (previous 0.8x) * Fixed typo on Input threshold specifications to VDD*0.25 and VDD*0.7 * Updated the INT_B VOL maximum level to 0.5 V (previous 0.4 V) * Updated limits on the POR to Active time to 250 s (min) to 450 s (max) (previous min was 40 s) * Clarified Operating voltage range (4.5 V to 28 V) 3.0 12/2014 * Corrected WAKE_B Max rating to 40 V. * Added Figure 19, SPI write operation and Figure 20, SPI read operation * Added Table 7.10.1, SPI check * Corrected Rb/W bits on Table 11 From 1/0 to 0/1 * Clarified SPI Read/write operation and SPI registers information. * Updated VBATP(POR) maximum voltage to 3.8 V. * Updated VBATP under voltage hysteresis minimum voltage to 250 mV * Updated VBATP low-power mode supply current to 40 uA * Input logic voltage threshold WAKE_B typical value added at 1.25 V, max value updated to 1.7 V * Added new Specification for WAKE_B input logic hysteresis. * Clarified AMUX accuracy and Coefficient accuracy specifications, added Figure 4, Divide by 6 coefficient accuracy. * Update internal pull-up resistance to 270 K (INT_B, WAKE_B, CS_B) * Low-power mode oscillator frequency centered at 192 KHz with +/- 15% tolerance. * Updated all timing specs derived from the 192 kHz oscillator (Low-power mode) * Added SBPOLLTIME (bit 13) selection functionality on 7.10.2, "Device configuration register" * Added SB Tactive Polling time specification (58 s or 1.2 ms Typical) * Table 6 Clarified wetting current specification for SB and SG channels. * SB sustain Current and Low-power mode polling current SB Typical value centered at 2.2mA, Min = 1.75 mA and Max = 2.65 mA, (+/- 20% tolerance). * Wetting current matching, Max value updated to 6% * Updated Switch detection Threshold in Low Voltage maximum value to 4.3 V. * Added Figure 22, Pulsed/continuous wetting current configuration * Removed section (Electrical Test requirement, Stress testing, and EMC consideration) 33978 63 NXP Semiconductors Revision Date Description of changes * Changed VESD1-2 to 2000 4.0 12/2014 * Changed ISUSSB max. value to 2.85 mA * Changed IACTIVEPOLLSB max. value to 2.85 mA * Changed PC33978EK and PC34978EK parts to MC in the Orderable part variations table * Deleted PC33978ES and PC34978ES part numbers * Updated case outline 8/2015 * Updated AMUX specification for QFN package 5.0 * Added thermal characteristics for QFN package 8/2015 6.0 * Added new part numbers MC33978AEK, MC33978AES, MC34978AEK, and MC34978AES to the Orderable part variations table * Updated VBATP HBM specification to 4.0 KV * Added additional line to VESD1-2 spec in Table 3 to show the max. value for MC33978/MC34978 and MC33978A/ MC34978A 8/2016 * Updated to NXP document form and style 2/2017 * Added note (4) to switch input voltage range in Table 3 * Added a new parameter tCSB_WAKEUP to Table 7 7.0 8/2017 * Updated the dynamic electrical characteristics condition statement in Table 7 (changed "VBATP = 4.5 V to 28 V" to "VBATP = 6.0 V to 28 V") 8.0 7/2018 * Changed document status from Advance Information to Technical Data 33978 NXP Semiconductors 64 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use NXP products. Home Page: NXP.com There are no expressed or implied copyright licenses granted hereunder to design or fabricate any integrated circuits Web Support: http://www.nxp.com/support anyproducts herein. based on the information in this document. NXP reserves the right to make changes without further notice to NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation, consequential or incidental damages. "Typical" parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by the customer's technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be found at the following address: http://www.nxp.com/terms-of-use.html. NXP, the NXP logo, Freescale, the Freescale logo and SMARTMOS are trademarks of NXP Semiconductors B.V. All other product or service names are the property of their respective owners. All rights reserved. (c) NXP B.V. 2018. Document Number: MC33978 Rev. 8.0 7/2018