www.osram-os.com Produktdatenblatt | Version 1.1 PL 450B PL 450B Metal Can (R) TO38 Blue Laser Diode in TO38 ICut Package Applications ----Projection Home LED & Laser ----Smoke Detectors ----Projection Professional LED & Laser ----Stage Lighting (LED & Laser) Features: ----Typical emission wavelength: 450 nm ----Efficient radiation source for cw and pulsed operation ----Single tranverse mode semiconductor laser ----High modulation bandwidth ----Miniaturized TO38 ICut package ----Laser diode isolated against package Ordering Information Type PL 450B 1 Version 1.0 | 2019-03-18 Peak output power typ. Popt 80 mW Ordering Code Q65111A0518 PL 450B Maximum Ratings TC=25C Parameter Symbol Values Operating temperature Top min. max. -40 C 70 C Storage temperature Tstg min. max. -40 C 85 C Junction temperature Tj max. 120 C Peak output power Popt max. 120 mW Forward current IF max. 165 mA Reverse voltage1) VR max. 2V Reverse voltage1) VR max. 12 V Soldering temperature tmax=10s TS max. 260 C Operation outside these conditions may damage the device. Operation at maximum ratings may influence lifetime. 2 Version 1.0 | 2019-03-18 PL 450B Characteristics Popt=80mW; Tcase = 25 C Parameter Symbol Reverse current1) IR max. 10 A Peak wavelength2) peak min. typ. max. 440 nm 450 nm 460 nm Operating current Iop typ. max. 75 mA 125 mA Spectral bandwidth at 50% Ie,rel,max typ. 1 nm Beam divergence (FWHM) parallel to pn-junction min. typ. max. 4 6.5 7.5 Beam divergence (FWHM) perpendicular to pn-junction min. typ. max. 18 22.5 25 Threshold current Ith typ. max. 17 mA 40 mA Forward voltage VF typ. max. 5.2 V 6.5 V TE polarization PTE typ. 100:1 Modulation frequency f min. 100 Thermal resistance junction case real RthJC typ. 38 K / W 3 Version 1.0 | 2019-03-18 Values PL 450B Relative Spectral Emission Popt=f() Beam Divergence 3) Popt = f(); Tcase = 25 C 4 Version 1.0 | 2019-03-18 3) PL 450B Optical Output Power Popt=f(IF) Threshold Current 3) Operating Voltage VF=f(IF) 3) Ith=f(Tcase); 5 Version 1.0 | 2019-03-18 3) PL 450B Dimensional Drawing 4) Further Information Approximate Weight: 1.0 mg ESD advice: ATTENTION - Observe Precautions For Handling - Electrostatic Sensitive Device. 6 Version 1.0 | 2019-03-18 PL 450B Electrical Internal Circuit Pin Description PIN 1 LD Anode PIN 2 Case PIN 3 LD Cathode 7 Version 1.0 | 2019-03-18 PL 450B Tray 4) 200 pieces per Tray Barcode-Product-Label (BPL) 8 Version 1.0 | 2019-03-18 (X ) PR OD NO : (1 T) LO T Width Length 215 5 mm 265 5 mm 9 Version 1.0 | 2019-03-18 P) : 12 (6 BA O : (9 D) D/ C: 01 44 8 5 14 2 110 0 (Q )Q 00 M (G ) GR OU ul LS ti Y TO T6 P 76 LE P: P -1 +Q 18 -1 R DE MY D Bi Bin1 Bi n2 : Pn3 : Q- 1ML : 1- 20 20 2 Te 2a 22 mp 3 24 0 ST Ad 26 0 C R 0 C R0 dit ion C R PA 77 al RT CK TE VA XT R: Muster 20 34 2199 : 12 2100 TY H S S em R ic AM on du O ct pto or H NO s TC 3G Schematic Transportation Box NO PL 450B 4) Box Barcode label Original packing label OHA02886 Dimensions of Transportation Box Height 95 5 mm PL 450B Notes Depending on the mode of operation, these devices emit highly concentrated visible and non visible light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions given in IEC 60825-1. Subcomponents of this device contain, in addition to other substances, metal filled materials including silver. Metal filled materials can be affected by environments that contain traces of aggressive substances. Therefore, we recommend that customers minimize device exposure to aggressive substances during storage, production, and use. Devices that showed visible discoloration when tested using the described tests above did show no performance deviations within failure limits during the stated test duration. Respective failure limits are described in the IEC60810. Important notes of operation for laser diode a) Electrical operation OSRAMs laser diodes are designed for maximum performance and reliability. Operating the laser diode above the maximum rating even for very short periods of time can damage the laser diode or reduce its lifetime. The laser diode must be operated with a suitable power supply with minimized electrical noise. The laser diode is very sensitive to electrostatic discharge (ESD). Proper precautions must be taken. b) Mounting instructions In order to maintain the lifetime of the laser diode proper heat management is essential. Due to the design of the laser diode heat is dissipated only through the base plate of the diode`s body. A proper heat conducting interconnection between the diodes base plate and the heat sink must be maintained. For further application related information please visit www.osram-os.com/appnotes 10 Version 1.0 | 2019-03-18 PL 450B Disclaimer Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version on the OSRAM OS webside. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Product safety devices/applications or medical devices/applications OSRAM OS components are not developed, constructed or tested for the application as safety relevant component or for the application in medical devices. In case Buyer - or Customer supplied by Buyer- considers using OSRAM OS components in product safety devices/applications or medical devices/applications, Buyer and/or Customer has to inform the local sales partner of OSRAM OS immediately and OSRAM OS and Buyer and /or Customer will analyze and coordinate the customer-specific request between OSRAM OS and Buyer and/or Customer. 11 Version 1.0 | 2019-03-18 PL 450B Glossary 1) Reverse Operation:Reverse Operation of 10 hours is permissible in total. Continuous reverse operation is not allowed. 2) Wavelength:peak is measured with an internal reproducibility of 0.3 nm (acc. to GUM with a coverage factor of k = 3). 3) Typical Values:Due to the special conditions of the manufacturing processes of semiconductor devices, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice. 4) Tolerance of Measure:Unless otherwise noted in drawing, tolerances are specified with 0.1 and dimensions are specified in mm. 12 Version 1.0 | 2019-03-18 PL 450B Revision History Version Date Change 1.0 2019-03-18 Initial Version 13 Version 1.0 | 2019-03-18 PL 450B Published by OSRAM Opto Semiconductors GmbH Leibnizstrae 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. 14 Version 1.0 | 2019-03-18