Please note that Cypress is an Infineon Technologies Company. The document following this cover page is marked as "Cypress" document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio. Continuity of document content The fact that Infineon offers the following product as part of the Infineon product portfolio does not lead to any changes to this document. Future revisions will occur when appropriate, and any changes will be set out on the document history page. Continuity of ordering part numbers Infineon continues to support existing part numbers. Please continue to use the ordering part numbers listed in the datasheet for ordering. www.infineon.com S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide Document Number: 002-08632 Rev. *B Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 www.cypress.com Copyrights (c) Cypress Semiconductor Corporation, 2015-2019. This document is the property of Cypress Semiconductor Corporation and its subsidiaries ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, "Security Breach"). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. "High-Risk Device" means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other medical devices. "Critical Component" means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, its directors, officers, employees, agents, affiliates, distributors, and assigns harmless from and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i) Cypress's published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 2 Preface This manual explains how to use the evaluation board. Be sure to read this manual before using the product. For this product, please consult with sales representatives or support representatives. Handling and Use Handling and use of this product and notes regarding its safe use are described in the manuals. Follow the instructions in the manuals to use this product. Keep this manual at hand so that you can refer to it anytime during use of this product. Notice on This Document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 3 Cautions Caution of the Products Described in This Document The following precautions apply to the product described in this manual. WARNING Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the user's system if the product is not used correctly. WARNING Do not look directly at LED. There is a possibility that your eye is hurt. Electric shock, Damage Electric shock, Damage CAUTION Cuts, Damage Cuts Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or devices connected to it, or may cause to loose software resources and other properties such as data, if the device is not used appropriately. Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your step when carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault. The product contains sharp edges that are left unavoidably exposed, such as jumper plugs. Handle the product with due care not to get injured with such pointed parts. Damage Do not place anything on the product or expose the product to physical shocks. Do not carry the product after the power has been turned on. Doing so may cause a malfunction due to overloading or shock. Damage Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage environments may cause a fault. Damage Use the product within the ranges given in the specifications. Operation over the specified ranges may cause a fault. Damage To prevent electrostatic breakdown, do not let your finger or other object come into contact with the metal parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body. Damage When turning the power on or off, follow the relevant procedure as described in this document. Before turning the power on, in particular, be sure to finish making all the required connections. Furthermore, be sure to configure and use the product by following the instructions given in this document. Using the product incorrectly or inappropriately may cause a fault. Damage Because the product has no casing, it is recommended that it be stored in the original packaging. Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when reshipping the product. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 4 Contents 1. Description ..................................................................................................................................................................... 6 2. S6SAL211A31-DALI-SA2 Board Specification ............................................................................................................ 7 3. PIN Descriptions ............................................................................................................................................................ 8 3.1 3.2 4. Setup and Verification ................................................................................................................................................... 9 4.1 4.2 5. S6SAL211A31-DALI-SA2 Component Layout ..................................................................................................... 21 S6SAL211A31-DALI-SA2 Wiring Layout ............................................................................................................. 22 S6SATU03 Component Layout ........................................................................................................................... 24 Circuit Schematic ........................................................................................................................................................ 25 6.1 6.2 7. Contents in a Package .......................................................................................................................................... 9 Evaluation with DALI Communication for S6SAL211A31SA3001 ....................................................................... 11 Layout ........................................................................................................................................................................... 21 5.1 5.2 5.3 6. Input/Output Connecter Descriptions ..................................................................................................................... 8 Switch Descriptions ............................................................................................................................................... 8 S6SAL211A31-DALI-SA2 Schematic .................................................................................................................. 25 S6SATU03 Schematic ......................................................................................................................................... 29 Component List ........................................................................................................................................................... 30 7.1 7.2 S6SAL211A31-DALI-SA2 Components List ........................................................................................................ 30 S6SATU03 Components List ............................................................................................................................... 33 8. S6SAL211A31-DALI-SA2 Property Data .................................................................................................................... 34 9. Board Picture ............................................................................................................................................................... 36 9.1 9.2 10. S6SAL211A31-DALI-SA2 Board Picture ............................................................................................................. 36 S6SATU03 Board Picture .................................................................................................................................... 37 Ordering Information ................................................................................................................................................... 38 Revision History ................................................................................................................................................................... 39 Document Revision History ........................................................................................................................................... 39 S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 5 1. Description S6SAL211A31SA2001 and S6SAL211A31SA3001 are starter kit tool for DALI communication system. A master board (S6SATU03) and a slave board (S6SAL211A31-DALI-SA2) are included in S6SAL211A31SA3001. A slave board (S6SAL211A31-DALI-SA2) is included in S6SAL211A31SA2001. Master board implements the communication circuits for DALI. Slave board is LED control board of 4CH 72W for intelligent LED lighting driver IC S6AL211A31. It is necessary to prepare a PC, 24V power supply, software, LED module and connection cable. When using S6SAL211A31SA2001, please prepare DALI Master additionally. Figure 1-1 DALI System Outline PC S6SATU03 Master GUI USB cable Power supply 24Vdc S6SAL211A31-DALI-SA2 DALI communication cable LED,Thermistor Slave S6SAL211A31SA2001 LED,Thermistor cable x4ch S6SAL211A31SA3001 S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 6 2. S6SAL211A31-DALI-SA2 Board Specification Figure 2-1 S6SAL211A31-DALI-SA2 Board Specification Item Symbol Min. Typ. Max. Unit Input voltage VIN 22 24 26 V Input current (VIN = 24V, ACTUAL LEVEL = 254 (max.)) IIN - 3.1 - A Input current (VIN = 24V, LED OFF, Include LED001 indicator current (1.7 mA)) IINoff - 3 - mA Output LED voltage VLEDout 0 18 VIN V Output LED current (Each channel, ACTUAL LEVEL = 254 (max.)) ILEDout - 1000 - mA Efficiency (VIN = 24V, ACTUAL LEVEL = 254 (max.)) - 95.8 - % The board size: 53 mm x 71.5 mm POWE ON LEVEL: 0.4% (*1) SYSTEM FAILRE LEVEL: 31% (*1) *1: The specification of DALI is 100%, but it's changed because it's safe. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 7 3. PIN Descriptions 3.1 Input/Output Connecter Descriptions Table 3-1 S6SAL211A31-DALI-SA2 Input/Output Pin Descriptions Connecter Symbol I/O Function Description CN_VIN I 24Vdc power supply terminal CN101,CN201,CN301,CN401 I/O CH1 -CH4 LED , thermistor terminal CN_DALI I/O DALI communication terminal Table 3-2 S6SATU03 Input/Output Pin Descriptions Connecter Symbol I/O Function Description CN101 I/O Mini USB connector CN_DALI I/O DALI communication terminal 3.2 Switch Descriptions Table 3-3 S6SAL211A31-DALI-SA2 Switch Descriptions Switch Description DALI short address physical selection Push in physical selection SW081 Initial Setting - Table 3-4 S6SATU03 Switch Descriptions Switch SW101 Description Reset push switch for MCU Initial Setting - S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 8 4. Setup and Verification 4.1 Contents in a Package Table 4-1 S6SAL211A31SA3001 Contents List No. Contents Description Quantity Notes 1 S6SAL211A31-DALI-SA2 LED control board of 4CH 72W with S6AL211A31 1 - 2 S6SATU03 DALI and USB communication board with FM3 1 - 3 USB cable USB to USB mini B cable 1 - Table 4-2 S6SAL211A31SA2001 Contents List No. 1 Contents S6SAL211A31-DALI-SA2 Description LED control board of 4CH 72W with S6AL211A31 Quantity 1 Notes - S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 9 Setup and Verification Figure 4-1 Contents Picture 1 2 3 S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 10 Setup and Verification 4.2 Evaluation with DALI Communication for S6SAL211A31SA3001 Using Items for Evaluation with I2C Control S6SAL211A31-DALI-SA2 1pic (*1) S6SATU03 1pic (*1) USB cable 1pic (*1) PC installed Windows7 or later OS 1pic (*2) Driver file 1pic (*3) DALI communication software 1pic (*3) 24V power supply 1pic (*2) LED module(IF 1A, VF 3.2V, 5 series x 4ch) 1set (*2) Connection cable 1set (*2) *1: Included in a package. *2: Please prepare. *3: Please download it from our device home page, S6AL211A31: Driver file install.bat in S6AL211_DALI_drivers.cab DALI communication software S6AL211_DALI_GUI.exe in S6AL211_DALI_GUI.cab 4.2.1 PC Setup for S6SATU03 1. Unpack the driver file to a folder of PC running Windows 7 or later version OS, and run install.bat file. 2. Connect S6SATU03 to PC using USB cable. 3. After installed a device, open the device manager and confirm the new COM port. Start menu Control panel Device manager 4. PC Setup is success if you can see "SIL Virtual Communication Port(COMx)" in Ports(COM & LPT). S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 11 Setup and Verification 4.2.2 Operation Check When Using S6SATU03 WARNING Do not look directly at LED. There is a possibility that your eye is hurt. 1. Connect CN_101,201,301,401 of S6SAL211A31-DALI-SA2 and LED by connection cable. *1 2. Connect CN_DALI of S6SATU03 and CN_DALI of S6SAL211A31-DALI-SA2 by DALI cable. *2 3. Connect CN101 of S6SATU03 and PC by USB cable. (LED101 near CN101 of S6SATU03 on board will shine in red.) 4. Run DALI communication software. 5. 24Vdc is applied to CN_VIN of S6SAL211A31-DALI-SA2. 6. LED of all channel are lighting. (Bright level is set POWER ON LEVEL of DALI command) 7. Send DALI command DAPC to BROADCAST ADDRESS from S6SATU03. You can control LED brightness. (Look at "Control Lighting by the broadcast") Figure 4-2 Board Connection CN DALI PC (*3) S6SATU03 GUI USB cable CN101 Power supply 24Vdc CN_VIN DALI communication line (*2) (No Polarity) CN DALI CN_101 CN_201 CN_301 CN_401 LED, Thermistor (*1) S6SAL211A31-DALI-SA2 LED,Thermistor cable x4ch 24Vdc CN_VIN CN DALI CN_101 CN_201 CN_301 CN_401 S6SAL211A31-DALI-SA2 (*4) Maximum DALI LIghting module (slave) number is 64. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 12 Setup and Verification *1: Connect LED to all CH from CN_101 to CN_401. Refer to Figure 4-3. *2: S6SATU03 can provide power to DALI communication lines from CN_DALI. This current limit is 50 mA (Supply voltage = 12V-20V).We must consider this current when determining the number of connected DALI Slave. We have to select the cable in consideration of the rated current and then rated voltage *3: Beforehand, make a setup of PC and install software. *4: A board of S6SAL211A31-DALI-SA2 is possible to buy as single item. (Part Number: S6SAL211A31SA2001) Figure 4-3 Connection of 6SAL211A31-DALI-SA2 and LED S6SAL211A31-DALI-SA2 CN_401 CN_301 CN_201 CN_101 LED,Thermistor THm THp LEDm LEDp THm THp LEDm LEDp THm THp LEDm LEDp THm THp LEDm LEDp (*2) (*1) (*2) (*1) *1: Connect LED to all CH from CN_101 to CN_401. LED module(IF 1A, VF 3.2V, 5- series ) Be careful about polarity. *2: Thermistor (THp,THm) is an option. Even if that isn't connected, a board operates. 4.2.3 GUI Control Function When Using S6SATU03 4.2.3.1 Preparing the Control GUI Run DALI communication software (S6AL211_DALI_GUI.exe) after connecting the USB cable. Show the message box below if the connecting GUI and DALI controller is success. Otherwise, check USB cable connection or installation of the device driver. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 13 Setup and Verification Later a few second, GUI shows the dialog box. Complete preparation. Note: Don't disconnect the USB cable while this GUI is running. Because it breaks down. 4.2.3.2 Exiting the Control GUI Crick "x" mark in the upper right. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 14 Setup and Verification 4.2.3.3 Checking State of the DALI Slave You can check the state of connecting DALI slaves in "Management" tab. Crick "SEARCH SHORT ADDRESS" button, then GUI will search some connected DALI slave. If you see no highlighted number, Please refer to 4.2.3.6 Control Lighting by the Short Address. And set the address. GUI found 4 DALI slaves above picture. Crick "CHECK STATUS" button, then GUI will show some connected DALI slave. If you crick "CHECK STATUS" button after checking "Repeat" check box, this GUI will update status of DALI slaves every second. GUI shows you that 2 DALI slaves are bright above picture. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 15 Setup and Verification 4.2.3.4 Control Lighting by the Broadcast DALI MASTER send to all connected DALI SLAVE by the broadcast in "control" tab. (Selected "BroadCast" Radio button in "Address Select" Group) Click Some Button and you can control lighting. ON(Max) button: Lighting starts at maximum level(default level 254). ON(Min) button: Lighting starts at minimum level(default level 1). OFF button: turn off lighting. UP: Increase lighting level at some pitch with fade. DOWN: reduce at some pitch with fade. STEP UP: One step up the lighting level. STEP DOWN: One step down the lighting level. DAPC: Direct Arc Power Control. Push this button after choosing the number (0-254) of the vertical scrollbar. Lighting level will set on the chosen number. GO TO SCENE: Set the lighting level to some scene after choosing number (0-15) of the drop box at left this button. Show later for "SCENE". Show below message box by selecting "Broadcast" radio button in "Address Select" group. If you select "Yes", you can use "CHECK STATUS" button and "SCENE". *Later mention: "CHECK STATUS", "SCENE". These functions by broadcast address can work correctly in the case of connecting only one DALI slave S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 16 Setup and Verification 4.2.3.5 Control Lighting by the Group DALI MASTER sends to each DALI group in "control" tab. (Selected "Group" Radio button in "Address Select" Group) Click Some Button and you can control lighting. The operations of each button (ON, OFF, (STEP) UP, (STEP) DOWN, DAPC, SCENE function) are same in broadcast. Group setting method is shown in "For the Group" of "Control Lighting by the short address". 4.2.3.6 Control Lighting by the Short Address DALI MASTER send to the particular DALI SLAVE by the short address. DALI SLAVE needs to choose short address number. Crick "Short Address Setting" tab. Push "SET SHORT ADDRESS" button after choosing from the drop box of left button. Short address selection is completed. Show blow window after choosing "Short Address" Radio button in "Address Select" Group S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 17 Setup and Verification Choose the short address the drop box in "Address Select" group, and you can control he lighting that have same short address. CHECK STATUS: Show the status of DALI slave. View Setting Panel: You can set SCENE, GROUP and each item by checking this check box. GUI will show the dialog box below Setting Panel Level, Fade, etc. For the LEVEL You can set each level from 1 to 254. (MAX LEVEL, MIN LEVEL, POWER ON LEVEL, SYSTEM FAILURE LEVEL). The fade time affects DAPC and SCENE. The fade rate affects UP and DOWN. For the FADE You can set the fade time and the fade rate. The fade time affects DAPC and SCENE. The fade rate affects UP and DOWN. Setting the FADE TIME 1. Select the fade time number (No fade-90.5sec) by drop box at left "SET FADE TIME" button. 2. Push "SET FADE TIME" button. You can confirm in running the fade function as pushing "CHECK STATUS" button. If DALI slave is in the fade function, "Fade Running" indicates "Running". S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 18 Setup and Verification Setting the FAST FADE TIME 1. Select the fast fade time number (<25ms - 675msec) by drop box at left "SET FAST FADE TIME" button with choosing No fade by SET FADE TIME. 2. Push "SET FAST FADE TIME" button. Setting the FADE RATE 1. Select the fade time number (1-15) by drop box at left "SET FADE RATE" button. 2. Push "SET FADE RATE" button. Select DIMMING CURVE You can select dimming curve, Logarithm or linear For the SCENE You can set lighting level as scene from 0 to 15. You can select lighting level in 1 action as choosing the scene number without using UP, DOWN, DPAC and etc. Using the SCENE You can set 16 scenes lighting level by below window. Example: Setting 125 in SCENE 2 1. Set Lighting level (0-254) to 125 by No. 2 Vscroll bar. 2. Select "2" scene number by drop box at left "STORE SCENE" button. 3. Push "STORE SCENE" button. 3 2 1 S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 19 Setup and Verification 4. Select "2" scene number by drop box at left "GOTO SCENE" button. 5. Push "GO TO SCENE" button, then the lighting level will be set to 125. 5 4 For the GROUP You can set lighting group from 0 to 15. Example: Setting group to No.5. 1. Select "5" group number by drop box at left "ADD GROUP" button. 2. Push "ADD GROUP" button. You can set group more than one for one DALI slave. 1 RESET Button 2 GUI shows "RESET" button with checking "View Setting Panel" check box. You can reset DALI slave with pushing "RESET" button. Note: This operation causes the lighting maximum level of LED. Below each level are reset by "RESET" button. (Example: MAX LEVEL=254, MIN LEVEL=1, POWER ON LEVEL=254, SYSTEM FAILURE LEVEL=254 At the time of 6SAL211A31-DALI-SA2 shipment, POWER ON LEVEL=1, SYSTEM FAILURE LEVEL=80) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 20 5. Layout 5.1 S6SAL211A31-DALI-SA2 Component Layout 53mm Figure 5-1 S6SAL211A31-DALI-SA2 Component Layout 71.5mm 53mm S6SAL211A31-DALI-SA2 Top side (Top view) 71.5mm S6SAL211A31-DALI-SA2 Bottom side (Top view) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 21 Layout 5.2 S6SAL211A31-DALI-SA2 Wiring Layout Figure 5-2 S6SAL211A31-DALI-SA2 Wiring Layout (Layer 1, Layer 2) S6SAL211A31-DALI-SA2 Layer 1 (Top view) S6SAL211A31-DALI-SA2 Layer 2 (Top view) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 22 Layout Figure 5-3 S6SAL211A31-DALI-SA2 Wiring Layout (Layer 3, Layer 4) S6SAL211A31-DALI-SA2 Layer 3 (Top view) S6SAL211A31-DALI-SA2 Layer 4 (Top view) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 23 Layout 5.3 S6SATU03 Component Layout 50mm Figure 5-4 S6SATU03 Component Layout 65mm 50mm S6SATU03 Top side (Top view) 65mm S6SATU03 Bottom side (Top view) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 24 6. Circuit Schematic 6.1 S6SAL211A31-DALI-SA2 Schematic Figure 6-1 S6SAL211A31-DALI-SA2 Circuit Schematic S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 25 Circuit Schematic Figure 6-2 S6SAL211A31-DALI-SA2 Circuit Schematic S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 26 Circuit Schematic Figure 6-3 S6SAL211A31-DALI-SA2 Circuit Schematic CH1 CH2 S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 27 Circuit Schematic Figure 6-4 S6SAL211A31-DALI-SA2 Circuit Schematic CH3 CH4 S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 28 Circuit Schematic 6.2 S6SATU03 Schematic Figure 6-5 S6SATU03 DALI Communication Circuit S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 29 7. Component List 7.1 S6SAL211A31-DALI-SA2 Components List Table 7-1 S6SAL211A31-DALI-SA2 Components List Rated Voltage(V) Rated Current(A) - 200 500m - 10 F 35 - - TDK 4.7 F 35 - - TDK 0.1 F 50 - - C1608X5R1V475K TDK 4.7 F 35 - - C1608X5R1V475K TDK 4.7 F 35 - - C006 C1608CH1H101J TDK 100 pF 50 - - C007 C1608CH1H101J TDK 100 pF 50 - - 9 C009 EKMG350ELL101MF11D NIPPON-CHEMI-CON 100 F 35 - - 10 C061 C3216X5R1V226M160AC TDK 22 F 35 - - 11 C101-1 C3216X5R1V475K160AB TDK 4.7 F 35 - - 12 C102-1 C3225X5R1H106K TDK 10 F 50 - - 50 No. Component Parts Number Vendor 1 BD061 MB2S FAIRCHILD 2 C001 C2012X5R1V106K125AC TDK 3 C002 C1608X5R1V475K 4 C003 C1608X5R1H104K080AA 5 C004 6 C005 7 8 Value Remarks 13 C102-3 C1608CH1H102J TDK 0.001 F 14 C120 C1608X5R1H104K080AA TDK 0.1 F 50 - NMT 15 C201-1 C3216X5R1V475K160AB TDK 4.7 F 35 - - 16 C202-1 C3225X5R1H106K TDK 10 F 50 - - 17 C202-3 C1608CH1H102J TDK 0.001 F 50 18 C220 C1608X5R1H104K080AA TDK 0.1 F 50 - NMT 19 C301-1 C3216X5R1V475K160AB TDK 4.7 F 35 - - - - - - NMT NMT 20 C302-1 C3225X5R1H106K TDK 10 F 50 21 C302-3 C1608CH1H102J TDK 0.001 F 50 22 C320 C1608X5R1H104K080AA TDK 0.1 F 50 - NMT 23 C401-1 C3216X5R1V475K160AB TDK 4.7 F 35 - - 24 C402-1 C3225X5R1H106K TDK 10 F 50 - - TDK 0.001 F 25 C402-3 C1608CH1H102J 50 - - NMT NMT S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 30 Component List Rated Voltage(V) Rated Current(A) 0.1 F 50 - NMT SATOPARTS - 50 3 - SATOPARTS - 50 3 - ML-700-NH-4P SATOPARTS - 50 3 - ML-700-NH-4P SATOPARTS - 50 3 - CN_DALI ML-2100-2P SATOPARTS - 300 7 - CN_VIN ML-2100-2P SATOPARTS - 300 7 - 33 D061 MBR140SFT1 ONSEMICONDUCTOR - 30 500m - 34 D101 SS23 FAIRCHILD - 30 2 - 35 D201 SS23 FAIRCHILD - 30 2 - 36 D301 SS23 FAIRCHILD - 30 2 - 37 D401 SS23 FAIRCHILD - 30 2 - 38 L101 SLF12575T-221M1R3 TDK 220 H - 1.3 - 39 L201 SLF12575T-221M1R3 TDK 220 H - 1.3 - 40 L301 SLF12575T-221M1R3 TDK 220 H - 1.3 - 41 L401 SLF12575T-221M1R3 TDK 220 H - 1.3 - 42 LED001 OSHR1608C1A OptoSupply - - 30m - 43 LED061 OSTG1608C1A OptoSupply - - 30m NMT 44 M001 S6AL211A SPANSION - - - - 45 PC061 PS2561L-1-A CEL - - - - 46 PC062 PS2561L-1-A CEL - - - - 47 Q061 FMMT491A DIODES - 40 1 - 48 Q101 FDC658AP FAIRCHILD - 30 4 - 49 Q102 FDC8886 FAIRCHILD - 30 6.5 - 50 Q201 FDC658AP FAIRCHILD - 30 4 - 51 Q202 FDC8886 FAIRCHILD - 30 6.5 - 52 Q301 FDC658AP FAIRCHILD - 30 4 - 53 Q302 FDC8886 FAIRCHILD - 30 6.5 - 54 Q401 FDC658AP FAIRCHILD - 30 4 - 55 Q402 FDC8886 FAIRCHILD - 30 6.5 - 56 R004 RR0816P-123-D SSM 12 k - - - 57 R020 RR0816P-103-D SSM 10 k - - - 58 R021 RR0816P-103-D SSM 10 k - - - 59 R061 RR0816P-681-D SSM 680 - - - 60 R062 RR0816P-331-D SSM 330 - - - 61 R063 RR0816P-332-D SSM 3.3 k - - - 62 R064 RK73H1JTTD4R70F KOA 4.7 - - - 63 R065 RR0816P-103-D SSM 10 k - - - 64 R066 RR0816P-562-D SSM 5.6 k - - - 65 R081 RR0816P-103-D SSM 10 k - - NMT 66 R082 RR0816P-104-D SSM 100 k - - - 67 R101 RL1632R-R200-F SSM 200 m - - - 68 R103 RK73Z1J KOA 0 - 1 - No. Component Parts Number Vendor 26 C420 C1608X5R1H104K080AA TDK 27 CN101 ML-700-NH-4P 28 CN201 ML-700-NH-4P 29 CN301 30 CN401 31 32 Value Remarks S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 31 Component List Rated Voltage(V) Rated Current(A) 1 M - - NMT KOA 1 M - - NMT KOA 0 - 1 - RR0816P-752-D SSM 7.5 k - - - RL1632R-R200-F SSM 200 m - - - R203 RK73Z1J KOA 0 - 1 - R204 RK73H1JTTD1004F KOA 1 M - - NMT 76 R206 RK73H1JTTD1004F KOA 1 M - - NMT 77 R207 RK73Z1J KOA 0 - 1 - 78 R220 RR0816P-752-D SSM 7.5 k - - - 79 R301 RL1632R-R200-F SSM 200 m - - - 80 R303 RK73Z1J KOA 0 - 1 - 81 R304 RK73H1JTTD1004F KOA 1 M - - NMT 82 R306 RK73H1JTTD1004F KOA 1 M - - NMT 83 R307 RK73Z1J KOA 0 - 1 - 84 R320 RR0816P-752-D SSM 7.5 k - - - 85 R401 RL1632R-R200-F SSM 200 m - - - 86 R403 RK73Z1J KOA 0 - 1 - 87 R404 RK73H1JTTD1004F KOA 1 M - - NMT 88 R406 RK73H1JTTD1004F KOA 1 M - - NMT 89 R407 RK73Z1J KOA 0 - 1 - 90 R420 RR0816P-752-D SSM 7.5 k - - - 91 SW081 SKRPACE010 ALPS - - 50m - 92 ZD061 MMSZ5229B FAIRCHILD - - - - No. Component Parts Number Vendor 69 R104 RK73H1JTTD1004F KOA 70 R106 RK73H1JTTD1004F 71 R107 RK73Z1J 72 R120 73 R201 74 75 Value Remarks NMT: No mount. These components are compliant with RoHS, and please ask each vendor for details if necessary. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 32 Component List 7.2 S6SATU03 Components List Table 7-2 S6SATU03 DALI Communication Components List No . Component Rated Voltage(V) Rated Current(A) Remarks 1 C01 C3216X5R1V226M160AC TDK 22 F 35 - - 2 D01 MBR140SFT1 3 D02 MBR140SFT1 ONSEMICONDUCTOR - 30 500m - ONSEMICONDUCTOR - 30 500m - 4 D14 MB2S FAIRCHILD - 200 500m - 5 6 IC01 NJM317DL1 NJR - 40 400m - LED_DALI OSYG1608C1A OptoSupply - - 30m - 7 R01 RK73H2BTTD24R0F KOA 24 - - - 8 R02 RR0816P-153-D SSM 15 k - - - 9 R03 RR0816P-681-D SSM 680 - - - 10 R04 RR0816P-331-D SSM 330 - - - 11 R05 RR0816P-332-D SSM 3.3 k - - - 12 R06 RR0816P-562-D SSM 5.6 k - - - 13 R07 RR0816P-562-D SSM 5.6 k - - - 14 R08 RR0816P-103-D SSM 10 k - - - 15 R09 RK73H1JTTD4R70F KOA 4.7 - - - 16 R10 RK73H2BTTD10R0F KOA 10 - - - 17 PC01 PS2561L-1-A CEL - - - - 18 PC02 PS2561L-1-A CEL - - - - 19 Q01 FMMT491A DIODES - 40 1 - 20 ZD01 MMSZ5229B FAIRCHILD 4.3 - - - 21 ZD02 MMSZ5229B FAIRCHILD - - - NMT 22 CN_DALI ML-2100-2P SATOPARTS - 300 7 - Parts Number Vendor Value NMT: No mount. These components are compliant with RoHS, and please ask each vendor for details if necessary. S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 33 8. S6SAL211A31-DALI-SA2 Property Data Figure 8-1 Switching Waveform CH1 100% Dimming VIN=24V, ILEDout=1A LEDLUW W5AM (5 series x 4ch) ACTUAL LEVEL=254(Logarithm) CH1: LED current (ILEDout) CH2: LEDp voltage (VLEDout) CH4: Switching node voltage CH1 1% Dimming VIN=24V, ILEDout=10 mA LEDLUW W5AM (5 series x 4ch) ACTUAL LEVEL=85(Logarithm) CH1: LED current (ILEDout) CH2: LEDp voltage (VLEDout) CH4: Switching node voltage S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 34 S6SAL211A31-DALI-SA2 Property Data CH1 0.1% Dimming VIN=24V, ILEDout=1 mA LEDLUW W5AM (5 series x 4ch) ACTUAL LEVEL=1(Logarithm) CH1: LED current (ILEDout) CH2: LEDp voltage (VLEDout) CH4: Switching node voltage S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 35 9. Board Picture 9.1 S6SAL211A31-DALI-SA2 Board Picture Figure 9-1 S6SAL211A31-DALI-SA2 Board Picture S6SAL211A31-DALI-SA2 (Top View) S6SAL211A31-DALI-SA2 (Bottom View) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 36 Board Picture 9.2 S6SATU03 Board Picture Figure 9-2 S6SATU03 Board Picture S6SATU03 (Top View) S6SATU03 (Bottom View) S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 37 10. Ordering Information Table 10-1 Ordering Information Part Number EVB Revision Note S6SAL211A31SA3001 S6SAL211A31-DALI-SA2 Rev1.0 S6SATU03 Rev1.0 - S6SAL211A31SA2001 S6SAL211A31-DALI-SA2 Rev1.0 - S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 38 Revision History Document Revision History Document Title: S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide Document Number: 002-08632 Revision Issue Date Origin of Description of Change Change ** 03/31/2015 HSAT Initial release *A 04/26/2016 HSAT Migrated Spansion Guide from S6SAL211A31SA3001_SS405-00003-1v0-E to Cypress format *B 04/04/2019 ATTS Updated Cypress logo and copyright S6SAL211A31SA2001, S6SAL211A31SA3001 4ch 72W LED Driver and Communication Board Operation Guide, Document Number: 002-08632 Rev. *B 39