User's Manual IE-784046-NS-EM1 Emulation Board Target device PD784046 Subseries Document No. U13744EJ1V0UM00 (1st edition) Date Published May 1999 N CP(K) (c) 1999 Printed in Japan PD784054 [MEMO] 2 User's Manual U13744EJ1V0UM00 Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. The information in this document is subject to change without notice. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or of others. M7A 96. 10 User's Manual U13744EJ1V0UM00 3 Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, pIease contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) NEC Electronics (Germany) GmbH NEC Electronics Hong Kong Ltd. Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 Benelux Office Eindhoven, The Netherlands Tel: 040-2445845 Fax: 040-2444580 Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 NEC Electronics (France) S.A. Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC Electronics (France) S.A. NEC Electronics Singapore Pte. Ltd. Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290 Spain Office Madrid, Spain Tel: 91-504-2787 Fax: 91-504-2860 United Square, Singapore 1130 Tel: 65-253-8311 Fax: 65-250-3583 NEC Electronics Italiana s.r.l. NEC Electronics (Germany) GmbH Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 Scandinavia Office Taeby, Sweden Tel: 08-63 80 820 Fax: 08-63 80 388 NEC Electronics (Germany) GmbH Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490 NEC Electronics (UK) Ltd. NEC Electronics Hong Kong Ltd. NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 Fax: 02-2719-5951 NEC do Brasil S.A. Electron Devices Division Rodovia Presidente Dutra, Km 214 07210-902-Guarulhos-SP Brasil Tel: 55-11-6465-6810 Fax: 55-11-6465-6829 J99.1 4 User's Manual U13744EJ1V0UM00 INTRODUCTION Product Overview The IE-784046-NS-EM1 is designed to be used with the IE-78K4-NS to debug the following target devices that belong to the 78K/IV Series of 16-bit single-chip microcontrollers. Target Readers * PD784046 Subseries: PD784044, 784046, 78F4046 * PD784054: PD784054 This manual is intended for engineers who will use the IE-784046-NS-EM1 with the IE78K4-NS to perform system debugging. Engineers who use this manual are expected to be thoroughly familiar with the target device's functions and use methods and to be knowledgeable about debugging. Organization When using the IE-784046-NS-EM1, refer to not only this manual (supplied with the IE784046-NS-EM1) but also the manual that is supplied with the IE-78K4-NS. IE-78K4-NS User's Manual * Basic specifications IE-784046-NS-EM1 User's Manual * General * System configuration * Part names * External interface functions * Installation * Differences between target devices and target interface circuits Purpose This manual's purpose is to explain various debugging functions that can be performed when using the IE-784046-NS-EM1 and the IE-78K4-NS. User's Manual U13744EJ1V0UM00 5 Terminology The meanings of certain terms used in this manual are listed below. Term Meaning Emulation device This is a general term that refers to the device in the emulator that is used to emulate the target device. It includes the emulation CPU. Emulation CPU This is the CPU block in the emulator that is used to execute user-generated programs. Target device This is the device (a real chip) that is the target for emulation. Target system This includes the target program and the hardware provided by the user. When defined narrowly, it includes only the hardware. IE system This refers to the combination of the IE-78K4-NS and the IE-784046-NS-EM1. Conventions Related Documents Data significance: Higher digits on the left and lower digits on the right Note: Footnote for item marked with Note in the text Caution: Information requiring particular attention Remark: Supplementary information The related documents (user's manuals) indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such. Document Name Document Number English IE-78K4-NS U13356E U13356J IE-784046-NS-EM1 This manual U13744J ID78K4-NS Integrated Debugger Reference WindowsTM Based U12796E U12796J PD784046 Subseries Hardware U11515E U11515J PD784054 Hardware U11719E U11719J Caution The documents listed above are subject to change without notice. Be sure to use the latest documents when designing. 6 Japanese User's Manual U13744EJ1V0UM00 CONTENTS CHAPTER 1 GENERAL ..............................................................................................................................11 1.1 System Configuration ............................................................................................................................... 12 1.2 Hardware Configuration............................................................................................................................ 14 1.3 Basic Specifications.................................................................................................................................. 15 CHAPTER 2 PART NAMES........................................................................................................................17 2.1 Parts of Main Unit ...................................................................................................................................... 18 CHAPTER 3 INSTALLATION .....................................................................................................................19 3.1 Connection ................................................................................................................................................. 20 3.2 Clock Settings............................................................................................................................................ 21 3.3 3.2.1 Overview of clock settings ............................................................................................................. 21 3.2.2 Main system clock settings............................................................................................................ 23 Pin Mask Function Settings...................................................................................................................... 28 3.3.1 Wait (WAIT) mask function............................................................................................................ 28 3.3.2 Wait display function setting .......................................................................................................... 28 3.3.3 NMI interrupt mask function........................................................................................................... 28 3.4 Low-Voltage Emulation Setting................................................................................................................ 29 3.5 External Trigger ......................................................................................................................................... 30 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS ......31 APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE..............................................................35 User's Manual U13744EJ1V0UM00 7 LIST OF FIGURES Figure No. Title Page 1-1. System Configuration .............................................................................................................................. 12 1-2. Basic Hardware Configuration .................................................................................................................. 14 2-1. IE-784046-NS-EM1 Part Names ............................................................................................................... 18 3-1. Connection of Emulation Probe ................................................................................................................ 20 3-2. External Circuits Used as System Clock Oscillator ..................................................................................... 21 3-3. When Using Clock That Is Already Mounted on Emulation Board ................................................................ 22 3-4. When Using User-Mounted Clock ............................................................................................................. 22 3-5. When Using an External Clock ................................................................................................................. 23 3-6. Connections on Parts Board (When Using Main System Clock or User-Mounted Clock) ................................ 24 3-7. Crystal Oscillator (When Using Main System Clock or User-Mounted Clock) ................................................ 26 3-8. Pin Alignment of Crystal Oscillator and Socket ........................................................................................... 26 3-9. External Trigger Input Position .................................................................................................................. 30 4-1. Equivalent Circuit 1 of Emulation Circuit .................................................................................................... 32 4-2. Equivalent Circuit 2 of Emulation Circuit .................................................................................................... 33 8 User's Manual U13744EJ1V0UM00 LIST OF TABLES Table No. Title Page 1-1. Basic Specifications ............................................................................................................................................. 15 3-1. Main System Clock Settings................................................................................................................................. 23 3-2. DIP Switch Setting for Wait (WAIT) Mask Function.............................................................................................. 28 3-3. DIP Switch Setting for Wait Display Function....................................................................................................... 28 3-4. DIP Switch Setting for NMI Interrupt Mask Function ............................................................................................ 28 A-1. NP-80GC Pin Assignments.................................................................................................................................. 35 User's Manual U13744EJ1V0UM00 9 [MEMO] 10 User's Manual U13744EJ1V0UM00 CHAPTER 1 GENERAL The IE-784046-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78K/IV Series of 16-bit single-chip microcontrollers. This chapter describes the IE-784046-NS-EM1's system configuration and basic specifications. * Target device * PD784046 Subseries * PD784054 User's Manual U13744EJ1V0UM00 11 CHAPTER 1 GENERAL 1.1 System Configuration Figure 1-1 illustrates the IE-784046-NS-EM1's system configuration. Figure 1-1. System Configuration Device fileNote 1 (sold separately) Debugger ID78K4-NS (sold separately) Control software Host machine PC-9800 Series or IBM PC/ATTM or compatibles Interface board IE-70000-98-IF-C (sold separately) Interface board IE-70000-PC-IF-C (sold separately) Interface card or Interface cable (NS IF Cable) IE-78K4-NS (sold separately) Interface cable In-circuit emulator NS CARD Cable MC CARD Cable IE-70000-CD-IF (sold separately) FG Cable IE-784046-NS-EM1 (This product) AC adapter IE-70000-MC-PS-B (sold separately) Emulation probeNote 2 (sold separately) Conversion socket/conversion adapterNote 3 (sold separately) 12 User's Manual U13744EJ1V0UM00 CHAPTER 1 GENERAL Notes 1. The device file is as follows, in accordance with the subseries. SxxxxDF784046: PD784046 Subseries, PD784054 2. The emulation probe is as follows, in accordance with the package. NP-80GC: 80-pin plastic QFP (GC-3B9 type) The NP-80GC is a product of Naito Densei Machida Mfg. Co., Ltd. For further information, contact Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-44-822-3813) 3. The conversion socket/conversion adapter are as follows, in accordance with the package. EV-9200GC-80: 80-pin plastic QFP (GC-3B9 type) User's Manual U13744EJ1V0UM00 13 CHAPTER 1 GENERAL 1.2 Hardware Configuration Figure 1-2 shows the IE-784046-NS-EM1's position in the basic hardware configuration. Figure 1-2. Basic Hardware Configuration Dedicated bus interface IE system IE-78K4-NS (sold separately) Host machine Interface board (sold separately) Interface card (sold separately) 14 78K4 main board (G-78K4 MAIN Board) IE-784046-NS-EM1 Emulation board (This product) 78K4 emulation board (G-78K4 EM Board) User's Manual U13744EJ1V0UM00 Emulation probe (sold separately) CHAPTER 1 GENERAL 1.3 Basic Specifications The IE-784046-NS-EM1's basic specifications are listed in Table 1-1. Table 1-1. Basic Specifications Parameter Description Target device PD784046 Subseries, PD784054 System clock Maximum: 16 MHz Factory setting: 16 MHz Clock supply External: Pulse input Internal: Maximum 32 MHz, factory setting 32 MHz Low-voltage support 4 V or higher User's Manual U13744EJ1V0UM00 15 [MEMO] 16 User's Manual U13744EJ1V0UM00 CHAPTER 2 PART NAMES This chapter introduces the parts of the IE-784046-NS-EM1 main unit. The packing box contains the emulation board (IE-784046-NS-EM1). If there are any missing or damaged items, please contact an NEC sales representative. Fill out and return the guarantee document that comes with the main unit. User's Manual U13744EJ1V0UM00 17 CHAPTER 2 PART NAMES 2.1 Parts of Main Unit Figure 2-1. IE-784046-NS-EM1 Part Names TP1 GND TP1 IE-784046-NS-EM1 Low Volt CN1 80GC EXTIN external trigger OFF SW1 DIP switch EXTOUT X1 UMCLK socket Probe connector CN1 80GC TVCC 18 User's Manual U13744EJ1V0UM00 CHAPTER 3 INSTALLATION This chapter describes methods for connecting the IE-784046-NS-EM1 to the IE-78K4-NS, emulation probe, etc. Mode setting methods are also described. Caution Connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the IE system and the target system has been switched OFF. User's Manual U13744EJ1V0UM00 19 CHAPTER 3 INSTALLATION 3.1 Connection (1) Connection with IE-78K4-NS main unit See the IE-78K4-NS User's Manual for a description of how to connect the IE-784046-NS-EM1 to the IE-78K4NS. (2) Connection with emulation probe See the IE-78K4-NS User's Manual for a description of how to connect an emulation probe to the IE-784046-NSEM1. On this board, connect the emulation probe to CN1. Caution Incorrect connection may damage the IE system. Be sure to read the emulation probe's user's manual for a detailed description of the connection method. Figure 3-1. Connection of Emulation Probe Emulation probe (NP-80GC) , , , , Emulation board (G-78K4 EM board) Main board (G-78K4 MAIN board) 20 User's Manual U13744EJ1V0UM00 CN1 80GC I/O emulation board (IE-784046-NS-EM1) CHAPTER 3 INSTALLATION 3.2 Clock Settings 3.2.1 Overview of clock settings The main system clock to be used during debugging can be selected from (1) to (3) below. (1) Clock that is already mounted on emulation board (2) Clock that is mounted by user (3) External clock If the target system includes an internal clock, select either "(1) Clock that is already mounted on emulation board" or "(2) Clock that is mounted by user". For an internal clock, the target device is connected to a resonator and the target device's internal oscillator is used. An example of the external circuit is shown in part (a) of Figure 3-2. During emulation, the resonator that is mounted on the target system is not used. Instead, it uses the clock that is mounted on the emulation board, which is installed for the IE-78K4-NS. If the target system includes an external clock, select "(3) External clock". For an external clock, a clock signal is supplied from outside of the target device and the target device's internal oscillator is not used. An example of the external circuit is shown in part (b) of Figure 3-2. Figure 3-2. External Circuits Used as System Clock Oscillator (a) Internal clock (b) External clock Target device X1 Target device External clock X2 X1 X2 User's Manual U13744EJ1V0UM00 21 CHAPTER 3 INSTALLATION (1) Clock that is already mounted on emulation board A crystal oscillator is already mounted on the emulation board. Its frequency is 32 MHz. Figure 3-3. When Using Clock That Is Already Mounted on Emulation Board IE-78K4-NS Target system IE-784046-NS-EM1 Mounted oscillator (to be used) Emulation probe Resonator (not used) Remark The clock that is supplied by the IE-784046-NS-EM1's oscillator (encircled in the figure) is used. (2) Clock that is mounted by user The user is able to mount any clock supported by the set specifications on the IE-784046-NS-EM1. First mount the resonator on the parts board, then attach the parts board to the IE-784046-NS-EM1. This method is useful when using a different frequency from that of the pre-mounted clock. Figure 3-4. When Using User-Mounted Clock IE-78K4-NS IE-784046-NS-EM1 Parts board Target system Emulation probe Resonator (to be used) Resonator (not used) Remark The clock that is supplied by the IE-784046-NS-EM1's resonator (encircled in the figure) is used. 22 User's Manual U13744EJ1V0UM00 CHAPTER 3 INSTALLATION (3) External clock An external clock connected to the target system can be used via an emulation probe. Figure 3-5. When Using an External Clock IE-78K4-NS Target system Emulation probe Clock generator (to be used) Remark The clock supplied by the target system's clock generator (encircled in the figure) is used. 3.2.2 Main system clock settings Table 3-1. Main System Clock Settings Frequency of Main System Clock IE-784046-NS-EM1 Parts Board (UMCLK) When using clock that is already mounted on emulation board 32 MHz Oscillator used When using clock mounted by user Other than 32 MHz Oscillator assembled by user When using external clock Caution Oscillator not used CPU Clock Source Selection (ID) Internal External When using an external clock, open the configuration dialog box when starting the integrated debugger (ID78K4-NS) and select "External" in the area (Clock) for selecting the CPU's clock source (this selects the user's clock). Remark The IE-784046-NS-EM1's factory settings are those listed above under "when using clock that is already mounted on emulation board". (1) When using clock that is already mounted on emulation board When the IE-784046-NS-EM1 is shipped, a 32-MHz crystal oscillator is already mounted in the IE-784046-NSEM1's UMCLK socket. When using the factory-set mode settings, there is no need to make any other hardware settings. When starting the integrated debugger (ID78K4-NS), open the configuration dialog box and select "Internal" in the area (Clock) for selecting the CPU's clock source (this selects the emulator's internal clock). User's Manual U13744EJ1V0UM00 23 CHAPTER 3 INSTALLATION (2) When using clock mounted by user The settings described under either (a) or (b) are required, depending on the type of clock to be used. When starting the integrated debugger (ID78K4-NS), open the configuration dialog box and select "Internal" in the area (Clock) for selecting the CPU's clock source (this selects the emulator's internal clock). (a) When using a ceramic resonator or crystal resonator * Items to be prepared * Parts board (supplied with IE-78K4-NS) * Capacitor CA * Ceramic resonator or crystal resonator * Capacitor CB * Resistor Rx * Solder kit <Steps> <1> Solder the target ceramic resonator or crystal resonator, resistor Rx, capacitor CA, and capacitor CB (all with suitable oscillation frequency) onto the supplied parts board (as shown below). Figure 3-6. Connections on Parts Board (When Using Main System Clock or User-Mounted Clock) Parts board (UMCLK) 1 14 Pin No. 2 13 2-13 Capacitor CB 3 12 3-12 Capacitor CA 4 11 5 10 4-11 Ceramic resonator or crystal resonator 6 9 5-10 Resistor Rx 7 8 8-9 Short Connection Circuit diagram 1 M HCU04 HCU04 5 Rx 10 4 3 CA 12 98 CLOCK OUT 11 13 CB 2 Remark The sections enclosed in broken lines indicate parts that are attached to the parts board. 24 User's Manual U13744EJ1V0UM00 CHAPTER 3 INSTALLATION <2> Prepare the IE-784046-NS-EM1. <3> Remove the crystal oscillator that is mounted in the IE-784046-NS-EM1's socket (the socket marked as UMCLK). <4> Connect the parts board (from <1> above) to the socket (UMCLK) from which the crystal oscillator was removed. Check the pin 1 mark to make sure the board is mounted in the correct direction. <5> Make sure that the parts board mounted in the UMCLK socket on the emulation board is wired as shown in Figure 3-6 above. <6> Install the IE-784046-NS-EM1 in the IE-78K4-NS. The above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. IE-78K4-NS side (Emulation device) VCC 1 M 4.7 k 6 HCU04 HCU04 9 VHC244 CLK IN 8 5 A B Rx 10 X 4 LVCC CA 12 ALS157 11 4.7 k 3 13 CB 2 Y VHC244 X1 Remark The sections enclosed in broken lines indicate parts that are attached to the parts board. User's Manual U13744EJ1V0UM00 25 CHAPTER 3 INSTALLATION (b) When using a crystal oscillator * Items to be prepared * Crystal oscillator (see pinouts shown in Figure 3-7) Figure 3-7. Crystal Oscillator (When Using Main System Clock or User-Mounted Clock) VCC NC GND CLOCK OUT <Steps> <1> Prepare the IE-784046-NS-EM1. <2> Remove the crystal oscillator that is mounted in the IE-784046-NS-EM1's socket (the socket marked as UMCLK). <3> Connect the crystal oscillator (from <2> above) to the socket (UMCLK) from which the crystal oscillator was removed. Insert the crystal oscillator pin into the socket aligning the pins as shown in the figure below. Figure 3-8. Pin Alignment of Crystal Oscillator and Socket Crystal oscillator NC GND Socket VCC CLOCK OUT 1 14 2 13 3 12 4 11 5 10 6 9 7 8 Crystal Oscillator Pin Name Socket Pin No. NC 1 GND 7 CLOCK OUT 8 VCC 14 <4> Install the IE-784046-NS-EM1 in the IE-78K4-NS. 26 User's Manual U13744EJ1V0UM00 CHAPTER 3 INSTALLATION The above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. IE-78K4-NS side (Emulation device) VCC VCC 4.7 k VHC244 Crystal oscillator CLK IN LVCC 4.7 k A Y B VHC244 ALS157 X1 (3) When using external clock No hardware settings are required for this situation. When starting the integrated debugger (ID78K4-NS), open the configuration dialog box and select "External" in the area (Clock) for selecting the CPU's clock source (this selects the user's clock). User's Manual U13744EJ1V0UM00 27 CHAPTER 3 INSTALLATION 3.3 Pin Mask Function Settings 3.3.1 Wait (WAIT) mask function By setting the DIP switch (SW1) in the IE-784046-NS-EM1, it is possible to mask the alternate function (WAIT) of pin P94 in the PD784046 Subseries, and the PD784054. Table 3-2. DIP Switch Setting for Wait (WAIT) Mask Function Status DIP Switch Setting 1 (WAITMSK) 2 (P94ON) No mask (initial setting) OFF ON Wait masked ON OFF Caution Do not set the DIP switch to settings other than those above. 3.3.2 Wait display function setting By setting the DIP switch (SW1) in the IE-784046-NS-EM1, it is possible to display the status of "waiting" with an LED light. Table 3-3. DIP Switch Setting for Wait Display Function Status DIP Switch Setting 3 (WAITLED) Wait (WAIT) status not displayed (initial setting) OFF Wait (WAIT) status displayed ON Caution When pin P94 is used as a port pin, unless the DIP switch is turned OFF the LED may light up. 3.3.3 NMI interrupt mask function By setting the DIP switch (SW1) in the IE-784046-NS-EM1, it is possible to mask the NMI interrupt, which is the alternate function of the P20 pin. Table 3-4. DIP Switch Setting for NMI Interrupt Mask Function Status DIP Switch Setting 1 (NMIMSK) No NMI mask (initial setting) ON NMI masked OFF Caution Because the NMI interrupt is the alternate function of the P20 pin, this pin cannot operate as the P20 pin when the NMI mask status has been set. 28 User's Manual U13744EJ1V0UM00 CHAPTER 3 INSTALLATION 3.4 Low-Voltage Emulation Setting Low-voltage emulation is possible in the IE system. When the target system is operating on low voltage, supply the same voltage as the target system to the TP1 terminal pin of the IE-784046-NS-EM1. Set the target voltage between 4 and 5 V. * Maximum current consumption of TP1 5V 300 mA . . . . . . 4V 200 mA User's Manual U13744EJ1V0UM00 29 CHAPTER 3 INSTALLATION 3.5 External Trigger To set up an external trigger, connect EXTOUT pin to the IE-784046-NS-EM1's check pin TP2, and EXTIN pin to TP3 as shown below. See the integrated debugger (ID-78K4-NS) User's Manual (U12796E) for descriptions of related use methods. Figure 3-9. External Trigger Input Position OFF CN1 80GC TP1 TP2 (EXTOUT) TVCC 30 TP3 (EXTIN) User's Manual U13744EJ1V0UM00 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS This chapter describes differences between the target device's signal lines and the signal lines of the IE-784046NS-EM1's target interface circuit. Although the target device is a CMOS circuit, the IE-784046-NS-EM1's target interface circuit consists of an emulation CPU, TTL, CMOS-IC, and other emulation circuits. When the IE system is connected with the target system for debugging, the IE system performs emulation so as to operate as the actual target device would operate in the target system. However, some minor differences exist since the operations are performed via the IE system's emulation. (1) Signals directly input/output to/from the emulation CPU (2) Signals input from the target system via a gate (3) Other signals The IE system's circuit is used as follows for signals listed in (1) to (3) above. (1) Signals directly input/output to/from the emulation CPU The following signals perform the same operations as in the PD784046 Subseries and the PD784054. For the signals related to ports excluding ports 7 and 8 (having alternate functions as pins for A/D converter), however, a 1-M pull-down resistor and 22- resistor are inserted in series. * Signals related to port 0 to 9 * CLKOUT signal * Signals related to A/D converter * AVREF * AVSS Caution The AVDD pin on the target system is not connected to the IE system. Either the power supply of the IE system or the power supply supplied to TP1 is supplied to the AVDD pin of the emulation CPU. User's Manual U13744EJ1V0UM00 31 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS Figure 4-1. Equivalent Circuit 1 of Emulation Circuit Probe side IE system side 22 P00 to P03 P00 to P03 1 M 22 P10 to P13 P10 to P13 1 M 22 AC244 P20 P20 1 M 22 P21 to P27 P21 to P27 1 M 22 P30 to P37 P30 to P37 1 M 22 P40 to P47 P40 to P47 1 M 22 P50 to P57 P50 to P57 1 M 22 P60 to P63 P60 to P63 1 M P70/ANI0 to P77/ANI7 P70/ANI0 to P77/ANI7 P80/ANI8 to P87/ANI15 P80/ANI8 to P87/ANI15 22 P90 to P94 P90 to P94 1 M AVREF AVREF LVCC AVDD Leave open AVSS 32 AVDD AVSS User's Manual U13744EJ1V0UM00 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS (2) Signals input from the target system via a gate Since the following signals are input via a gate, their timing shows a delay compared to that of the PD784046 Subseries and the PD784054. Their AC characteristics and DC characteristics are therefore different from PD784046 Subseries and the PD784054, making it necessary to observe a stricter timing design than in the case of PD784046 Subseries and the PD784054. * RESET signal * Signals related to clock input Figure 4-2. Equivalent Circuit 2 of Emulation Circuit Probe side IE system side LVCC 100 k RESET ACT244 RESET 24 IE-784046-NS-EM1 X1 mounted clock VCC ALS157 4.7 k CLK IN LVCC 4.7 k VHC244 VHC244 X1 Target probe X1 pin Leave open X2 (3) Other signals * VDD pin When the emulation CPU is operating at 5 V, its power is supplied from the internal IE system, but when operating at low voltage, its power is supplied from the low-voltage pin (TP1). The VDD pin of the target system is only used to control the LED (TVCC) in the IE system that monitors the input of the target system's power supply. * VSS pin The VSS pin is connected to GND inside the IE system. * TEST pin The TEST pin is not used in the IE system. User's Manual U13744EJ1V0UM00 33 [MEMO] 34 User's Manual U13744EJ1V0UM00 APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. NP-80GC Pin Assignments (1/2) Emulation Probe CN1 Pin No. Emulation Probe CN1 Pin No. 1 114 34 49 2 113 35 50 3 108 36 45 4 107 37 46 5 104 38 41 6 103 39 42 7 100 40 35 8 99 41 8 9 94 42 7 10 93 43 14 11 30 44 13 12 29 45 18 13 24 46 17 14 23 47 22 15 20 48 21 16 19 49 28 17 16 50 27 18 15 51 92 19 10 52 91 20 9 53 98 21 37 54 97 22 43 55 102 23 44 56 101 24 47 57 106 25 48 58 105 26 51 59 112 27 52 60 111 28 57 61 83 29 58 62 77 30 59 63 78 31 60 64 73 32 55 65 74 33 56 66 69 Remarks 1. The NP-80GC is a product of Naito Densei Machida Mfg. Co., Ltd. 2. The numbers in the "Emulation probe" column indicate the corresponding pin number on the emulation probe tip. User's Manual U13744EJ1V0UM00 35 APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. NP-80GC Pin Assignments (2/2) Emulation Probe CN1 Pin No. Emulation Probe CN1 Pin No. 67 70 74 71 68 63 75 72 69 64 76 75 70 61 77 76 71 62 78 79 72 65 79 80 73 66 80 85 Remarks 1. The NP-80GC is a product of Naito Densei Machida Mfg. Co., Ltd. 2. The numbers in the "Emulation probe" column indicate the corresponding pin number on the emulation probe tip. 36 User's Manual U13744EJ1V0UM00 [MEMO] User's Manual U13744EJ1V0UM00 37 [MEMO] 38 User's Manual U13744EJ1V0UM00 Facsimile Message From: Name Company Tel. Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation. Please complete this form whenever you'd like to report errors or suggest improvements to us. FAX Address Thank you for your kind support. North America Hong Kong, Philippines, Oceania NEC Electronics Inc. NEC Electronics Hong Kong Ltd. Corporate Communications Dept. Fax: +852-2886-9022/9044 Fax: 1-800-729-9288 1-408-588-6130 Korea Europe NEC Electronics Hong Kong Ltd. NEC Electronics (Europe) GmbH Seoul Branch Technical Documentation Dept. Fax: 02-528-4411 Fax: +49-211-6503-274 South America NEC do Brasil S.A. Fax: +55-11-6465-6829 Asian Nations except Philippines NEC Electronics Singapore Pte. Ltd. Fax: +65-250-3583 Japan NEC Semiconductor Technical Hotline Fax: 044-548-7900 Taiwan NEC Electronics Taiwan Ltd. Fax: 02-2719-5951 I would like to report the following error/make the following suggestion: Document title: Document number: Page number: If possible, please fax the referenced page or drawing. Document Rating Excellent Good Acceptable Poor Clarity Technical Accuracy Organization CS 99.1