SITRANS F
Electromagnetic flowmeters
SITRANS F M MAG 5100 W
Operating Instructions • 11/2010
SITRANS F
1
Introduction
2
Safety notes
3
Description
SITRANS F 4
Installing/Mounting
Electromagnetic Flowmeters
SITRANS F M MAG 5100 W
5
Connecting
6
Service and maintenance
Operating Instructions 7
Troubleshooting/FAQs
8
Technical data
A
Appendix
Electromagnetic sensor type SITRANS F M MAG
5100 W for use with transmitter types SITRANS F M
MAG 5000/6000/6000I
11/2010
A5E03063678-02
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG order number: A5E03063678 Copyright © Siemens AG 2010.
Industry Sector Ⓟ 11/2010 Technical data subject to change
Postfach 48 48
90026 NÜRNBERG
GERMANY
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 3
Table of contents
1 Introduction................................................................................................................................................ 5
1.1 Items supplied................................................................................................................................5
1.2 History............................................................................................................................................5
1.3 Further Information ........................................................................................................................6
2 Safety notes............................................................................................................................................... 7
2.1 Laws and directives .......................................................................................................................7
2.2 Installation in hazardous area........................................................................................................9
2.3 Certificates ...................................................................................................................................10
3 Description............................................................................................................................................... 11
3.1 System components ....................................................................................................................11
3.2 Theory of operation......................................................................................................................12
4 Installing/Mounting................................................................................................................................... 15
4.1 Installation safety precautions......................................................................................................15
4.2 Determining a location .................................................................................................................16
4.3 Orienting the sensor.....................................................................................................................18
4.4 Mounting ......................................................................................................................................19
4.5 Potential equalization...................................................................................................................21
5 Connecting .............................................................................................................................................. 23
5.1 Remote installation ......................................................................................................................24
5.2 Installation check .........................................................................................................................26
5.3 Potting..........................................................................................................................................26
5.4 Direct burial..................................................................................................................................28
6 Service and maintenance ........................................................................................................................ 29
6.1 Maintenance.................................................................................................................................29
6.2 Recalibration ................................................................................................................................29
6.3 Transportation/storage.................................................................................................................29
6.4 Unit repair.....................................................................................................................................30
6.5 Technical support.........................................................................................................................30
6.6 Return procedures .......................................................................................................................31
7 Troubleshooting/FAQs............................................................................................................................. 33
7.1 Sensor check ...............................................................................................................................33
7.2 Fluctuating process values ..........................................................................................................35
Table of contents
SITRANS F M MAG 5100 W
4 Operating Instructions, 11/2010, A5E03063678-02
8 Technical data ......................................................................................................................................... 37
8.1 MAG 5100 W...............................................................................................................................37
8.2 Cable data................................................................................................................................... 40
8.3 Effect of temperature on working pressure ................................................................................. 41
8.4 Process fluid conductivity............................................................................................................ 42
8.5 Liner selection ............................................................................................................................. 43
8.6 Electrode selection...................................................................................................................... 43
8.7 Sizing tables................................................................................................................................ 44
8.8 Dimensions and weight............................................................................................................... 46
A Appendix.................................................................................................................................................. 51
A.1 Flange mating dimensions (metric)............................................................................................. 51
A.2 Factory settings........................................................................................................................... 53
A.3 Coil resistance............................................................................................................................. 55
A.4 Ordering ...................................................................................................................................... 57
Glossary .................................................................................................................................................. 59
Index........................................................................................................................................................ 61
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 5
Introduction 1
These instructions contain all the information you need for using the device.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it as well as service and
maintenance engineers.
Note
It is the responsibility of the customer that the instructions and directions provided in the
manual are read, understood and followed by the relevant personnel before installing the
device.
1.1 Items supplied
SITRANS F M MAG 5100 W
Calibration report
SITRANS F M literature CD
Quick Start guide
1.2 History
The contents of these instructions are regularly reviewed and corrections are included in
subsequent editions. We welcome all suggestions for improvement.
The following table shows the most important changes in the documentation compared to
each previous edition.
Edition Remarks
11/2010 Minor updates
07/2010 First edition
Replaces MAG 5100 W part of SITRANS F M Handbook (A5E02435647) and MAG 5100
W instruction (A5E00718677)
Introduction
1.3 Further Information
SITRANS F M MAG 5100 W
6 Operating Instructions, 11/2010, A5E03063678-02
1.3 Further Information
The contents of these Operating Instructions shall not become part of or modify any prior or
existing agreement, commitment or legal relationship. All obligations on the part of Siemens
AG are contained in the respective sales contract which also contains the complete and
solely applicable warranty conditions. Any statements contained herein do not create new
warranties or modify the existing warranty.
Product information on the Internet
The Operating Instructions are available on the CD-ROM shipped with the device, and on
the Internet on the Siemens homepage, where further information on the range of SITRANS
F flowmeters may also be found:
Product information on the internet (http://www.siemens.com/flowdocumentation)
Worldwide contact person
If you need more information or have particular problems not covered sufficiently by the
operating instructions, please get in touch with your contact person. You can find contact
information for your local contact person on the Internet:
Local contact person (http://www.automation.siemens.com/partner)
See also
Technical support (Page 30)
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 7
Safety notes 2
CAUTION
Correct, reliable operation of the product requires proper transport, storage, positioning and
assembly as well as careful operation and maintenance. Only qualified personnel should
install or operate this instrument.
Note
Alterations to the product, including opening or improper repairs of the product, are not
permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.
2.1 Laws and directives
General requirements
Installation of the equipment must comply with national regulations.
Instrument safety standards
The device has been tested at the factory, based on the safety requirements. In order to
maintain this condition over the expected life of the device the requirements described in
these Operating Instructions must be observed.
CAUTION
Material compatibility
Siemens Flow Instruments can provide assistance with the selection of wetted sensor
parts. However, the full responsibility for the selection rests with the customer and Siemens
Flow Instruments can take no responsibility for any failure due to material incompatibility.
Safety notes
2.1 Laws and directives
SITRANS F M MAG 5100 W
8 Operating Instructions, 11/2010, A5E03063678-02
CE marked equipment
All meters carry either a CE mark or a CE mark followed by eg.200
● CE200: This indicates that the product conforms to:
– PED 97/23/EC
– LVD 2006/95/EC
– EMC 2004/108/EC
● CE: This indicates that the product conforms to:
– LVD 2006/95/EC
– EMC 2004/108/EC
Compliance with PED directive
"Pressure Equipment Directive" (PED) is mandatory for all pressure equipment sold within
the EU and EFTA.
Siemens Flow Instruments products confirms to PED by following the tables below.
Table 2- 1 MAG 5100 W (7ME6580 only DN15 ... 600 (½" ... 24"))
Flange mm PN 10 PN 16 PN 40 150 lb 300 lb
15 N/A N/A SEP SEP N/A
25 N/A N/A SEP SEP N/A
40 N/A N/A SEP SEP N/A
50 N/A SEP N/A SEP N/A
65 N/A SEP N/A SEP N/A
80 N/A SEP N/A SEP N/A
100 SEP SEP N/A SEP N/A
125 N/A SEP N/A PED N/A
150 N/A PED N/A PED N/A
200 SEP PED N/A PED N/A
250 LVD PED N/A PED N/A
300 LVD PED N/A PED N/A
350 LVD PED N/A PED N/A
400 LVD PED N/A PED N/A
450 LVD PED N/A PED N/A
500 LVD PED N/A PED N/A
600 LVD PED N/A PED N/A
700 LVD PED* N/A N/A PED
750 N/A N/A N/A N/A PED
Safety notes
2.2 Installation in hazardous area
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 9
800 LVD PED* N/A N/A PED
900 LVD PED* N/A N/A PED
1000 LVD PED* N/A N/A PED
1050 N/A N/A N/A N/A PED
1100 N/A N/A N/A N/A PED
1200 LVD PED* N/A N/A PED
The key to the tables is as follows:
PED Product covered by PED and only available as fully PED-conforming
PED* Product covered by PED but available as either conforming or non-conforming to
PED
SEP Excluded from PED under Sound Engineering Practice
LVD Excluded from PED under the Low Voltage Directive
2.2 Installation in hazardous area
WARNING
Equipment used in hazardous areas must be approved for use in hazardous area and
marked accordingly. It is required that the special conditions for safe use provided in the
manual and in the FM / CSA certificates are followed!
Safety notes
2.3 Certificates
SITRANS F M MAG 5100 W
10 Operating Instructions, 11/2010, A5E03063678-02
Hazardous area approvals
The device is approved for use in hazardous area and has the following approvals:
● MAG 5100 W DN 15 ... 1200: FM / CSA Class I, Div. 2
WARNING
Make sure the hazardous area approval is suitable for the environment in which the
device will be installed.
WARNING
All approvals are based on non-flammable processes only!
WARNING
Potential equalization
In operation, the output is earthed through the conductive medium being measured and
therefore potential equalisation is necessary throughout the hazardous area.
The apparatus housing shall be connected to the potential equalising conductor in the
hazardous area.
WARNING
Laying of cables
Cables for use in hazardous area must satisfy the requirements for having a proof
voltage < AC 500 V applied between the conductor/ground, conductor/shield and
shield/ground.
Connect the devices that are operated in hazardous areas as per the stipulations
applicable in the country of operation.
2.3 Certificates
Certificates are posted on the Internet and on the documentation CD-ROM shipped with the
device.
See also
Technical data (Page 37)
Certificates on the Internet (http://www.siemens.com/processinstrumentation/certificates)
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 11
Description 3
The main applications of the SITRANS F M electromagnetic flow sensors can be found in the
following fields:
● Process industry
● Chemical industry
● Steel industry
● Mining
● Utility
● Power generation & distribution
● Oil & gas / HPI
● Water & waste water
● Pulp & paper
3.1 System components
The SITRANS F M USM II flowmeter system includes:
● Transmitter (types: SITRANS F M MAG 5000/6000 or MAG 6000 I)
● Sensor (types: SITRANS F M MAG 1100/1100F, MAG 3100/3100 P or MAG 5100 W)
● Communication module (optional) (types: HART, PROFIBUS PA/DP, MODBUS RTU RS
485, Foundation Fieldbus H1, Devicenet)
● SENSORPROM memory unit
Communication solutions
The SITRANS F USM II range of add on modules, presently including HART, Foundation
Fieldbus. MODBUS RTU RS 485, PROFIBUS PA / DP and Devicenet, are all applicable with
the SITRANS F M MAG 6000 transmitter.
Description
3.2 Theory of operation
SITRANS F M MAG 5100 W
12 Operating Instructions, 11/2010, A5E03063678-02
The SITRANS F M MAG 5100 W sensor housing and flanges are designed in carbon steel
and terminal box in fibre glass reinforced polyamide. Measuring pipe is made of stainless
steel (AISI 304) and liners are available in NBR Hard Rubber, Ebonite Hard Rubber, or
EPDM, which makes the sensor highly resistant to a wide range of chemicals. Electrodes are
made of Hastelloy.
MAG 5100W DN15 ... 40 MAG 5100W DN50 ... 300 MAG 5100W DN350 ... 1200
(7ME6520)
MAG 5100W DN25 ... 2000
(7ME6580)
MAG 5100W compact
installation with MAG
5000/6000 IP67
MAG 5100W compact
installation with MAG 6000 I
The sensors carry a wide range of approvals, see Technical data (Page 37).
3.2 Theory of operation
The flow measuring principle is based on Faraday’s law of electromagnetic induction.
0DJQHWLF)LHOG
)ORZ
Description
3.2 Theory of operation
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 13
Ui = When an electrical conductor of length L is moved at velocity v, perpendicular to the
lines of flux through a magnetic field of strength B, the voltage Ui is induced at the ends of
the conductor
Ui = L x B x v
● Ui = Induced voltage
● L = Conductor length = Inner pipe diameter = k1
● B = Magnetic field strength = k2
● v = Velocity of conductor (media)
● k = k1 x k2
Ui = k x v, the electrode signal is directly proportional to the fluid velocity
Operating principle
The coil current module generates a pulsating magnetizing current that drives the coils in the
sensor. The current is permanently monitored and corrected. Errors or cable faults are
registered by the self-monitoring circuit.
Input circuit amplifies the flow-proportional induced voltage signal from the electrodes. The
input impedance is extremely high: >1014 Ω which allows flow measurements on fluids with
conductivities as low as 5 µS/cm. Measuring errors due to cable capacitance are eliminated
due to active cable screening.
Digital signal processor converts the analog flow signal to a digital signal and suppresses
electrode noise through a digital filter. Inaccuracies in the transmitter as a result of long-term
drift and temperature drift are monitored and continuously compensated for via the self-
monitoring circuit. The analog to digital conversion takes place in an ultra low noise ASIC
with 23 bit signal resolution. This has eliminated the need for range switching. The dynamic
range of the transmitter is therefore unsurpassed with a turn down ratio of minimum 3000:1.
Description
3.2 Theory of operation
SITRANS F M MAG 5100 W
14 Operating Instructions, 11/2010, A5E03063678-02
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 15
4
Installing/Mounting
SITRANS F flowmeters with minimum IP67/NEMA 4X enclosure rating are suitable for in-
and outdoor installations.
● Make sure that pressure and temperature specifications indicated on the device
nameplate / label will not be exceeded.
WARNING
Installation in hazardous location
Special requirements apply to the location and interconnection of sensor and
transmitter. See "Installation in hazardous area" (Page 9)
4.1 Installation safety precautions
WARNING
In applications with working pressures/media that can be dangerous to people,
surroundings, equipment or others in case of pipe fracture, we recommend that special
precautions such as special placement, shielding or installation of a security guard or a
security valve are taken when the sensor is mounted.
● Ensure that stresses and loading caused by e.g. earthquakes, traffic, high winds and fire
damage if appropriate are taken into account during installation.
● Ensure that the flowmeter is installed such that it does not act as a focus for pipeline
stresses. External loadings are not taken into account in the flowmeter design.
● Provide adequate protection to minimise any risk of contact with hot surfaces.
WARNING
Prevent personal injuries by assuring that operation below pressure guards cannot take
place, if working with vacuum or fluids boiling readily.
Installing/Mounting
4.2 Determining a location
SITRANS F M MAG 5100 W
16 Operating Instructions, 11/2010, A5E03063678-02
4.2 Determining a location
NOTICE
The sensor must always be completely filled with liquid.
● Locate the the flowmeter in u-shaped pipes if pipes are only partially filled or have free
outlet
Figure 4-1 Correct installation in U-tube
● Avoid the following installations
– Installation at the highest point in the pipe system
– Installation in vertical pipes with free outlet
Figure 4-2 Correct installation with filled pipes
Figure 4-3 Correct installation at low point in system before outlet
Inlet and outlet conditions
To achieve accurate flow measurement it is essential to have straight lengths of inlet and
outlet pipes and a certain distance to pumps and valves.
It is also important to centre the flowmeter in relation to pipe flanges and gaskets.
Installing/Mounting
4.2 Determining a location
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 17
Figure 4-4 Inlet and outlet conditions
Installation in large pipes
The flowmeter can be installed between two reducers (e.g. DIN 28545). At 8° the following
pressure drop curves apply. The curves are applicable to water.
Example:
A flow of 3 m/s (V) in a sensor with a diameter reduction from DN 100 to DN 80 (d1/d2 = 0.8)
gives a pressure drop of 2.9 mbar.
Installing/Mounting
4.3 Orienting the sensor
SITRANS F M MAG 5100 W
18 Operating Instructions, 11/2010, A5E03063678-02
4.3 Orienting the sensor
The sensor operates in all orientations, but Siemens has the following recommendations:
● Vertical installation with an upwards flow
Figure 4-5 Vertical orientation, upwards flow
CAUTION
Abrasive liquids / liquids containing solid particles
A vertical installation minimizes wear and deposits in the sensor
NOTICE
Gas/air bubbles in the liquid
A vertical installation minimizes any negative effect of gas/air bubbles in the liquid
● Horizontal installation, terminal box upwards or downwards
Figure 4-6 Horizontal installation, various terminal box positions
CAUTION
Do NOT mount the sensor with the terminal box sideways
This will position the electrodes at the top where there is possibility for air bubbles and
at the bottom where there is possibility for mud, sludge, sand etc.
NOTICE
Empty pipe detection
For applications with empty pipe detection, the sensor can be tilted 45°, as shown
above.
Installing/Mounting
4.4 Mounting
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 19
4.4 Mounting
● Install the sensor in rigid pipelines in order to support the weight of the meter.
● Center the connecting pipelines axially in order to avoid turbulent flow profiles.
● Use proper gaskets according to liner type
Figure 4-7 Correct installation with gaskets
Vibrations
Avoid strong vibrations.
Figure 4-8 Avoid vibrations
CAUTION
In applications with strong vibrations, Siemens recommend remote mounting of the
transmitter!
Installing/Mounting
4.4 Mounting
SITRANS F M MAG 5100 W
20 Operating Instructions, 11/2010, A5E03063678-02
Torques
Fasten screws according to the torques values below
Figure 4-9 Torques values
NOTICE
Torque values are calculated on the basis of use of gaskets.
Table 4- 1 Maximum allowable torques
DN PN 10 PN 16 PN 40 Class 150 AWWA
Mm Inch Nm F/lbs Nm F/lbs Nm F/lbs Nm F/lbs Nm F/lbs
15 ½ N/A N/A N/A N/A 10 7 6 5 N/A N/A
25 1" N/A N/A N/A N/A 10 7 7 5 N/A N/A
40 1½" N/A N/A N/A N/A 16 12 9 7 N/A N/A
50 2" N/A N/A N/A N/A N/A N/A 25 18 N/A N/A
65 2½" N/A N/A 25/25 18/18 N/A N/A 25 18 N/A N/A
80 3" N/A N/A 25/25 18/18 N/A N/A 34 25 N/A N/A
100 4" N/A N/A 25/25 18/18 N/A N/A 26 19 N/A N/A
125 5" N/A N/A 29/32 21/24 N/A N/A 42 31 N/A N/A
150 6" N/A N/A 50/50 37/37 N/A N/A 57 42 N/A N/A
200 8" 50/50 37/37 50/52 37/38 N/A N/A 88 65 N/A N/A
250 10" 50/50 37/37 82/88 61/65 N/A N/A 99 73 N/A N/A
300 12" 57/62 42/46 111/117 82/86 N/A N/A 132 97 N/A N/A
350 14" 60/60 44/44 120/120 89/89 N/A N/A 225 166 N/A N/A
400 16" 88/88 65/65 170/170 125/125 N/A N/A 210 155 N/A N/A
450 18" 92/92 68/68 170/170 125/125 N/A N/A 220 162 N/A N/A
500 20" 103/103 76/76 230/230 170/170 N/A N/A 200 148 N/A N/A
600 24" 161/161 119/119 350/350 258/258 N/A N/A 280 207 N/A N/A
700 28" 200/200 148/148 304/304 224/224 N/A N/A N/A N/A 200 148
750 30" N/A N/A N/A N/A N/A N/A N/A N/A 240 177
Installing/Mounting
4.5 Potential equalization
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 21
Class 150 AWWA DN PN 10 PN 16 PN 40
800 32" 274/274 202/202 386/380 285/285 N/A N/A N/A N/A 260 192
900 36" 288/288 213/213 408/408 301/301 N/A N/A N/A N/A 240 177
1000 40" 382/382 282/282 546/546 403/403 N/A N/A N/A N/A 280 207
1050 42" N/A N/A N/A N/A N/A N/A N/A N/A 280 207
1100 44" N/A N/A N/A N/A N/A N/A N/A N/A 290 214
1200 48" 395/395 292/292 731/731 539/538 N/A N/A N/A N/A 310 229
1400 54" -/503 -/317 -/736 -/543 N/A N/A N/A N/A 528 389
1600 66" -/684 -/505 -/913 -/674 N/A N/A N/A N/A 698 515
1800 72" -/771 -/569 -/937 -/692 N/A N/A N/A N/A 700 516
2000 78" -/867 -/640 -/1128 -/832 N/A N/A N/A N/A 890 656
4.5 Potential equalization
To obtain optimum results from the measuring system, the sensor must have the same
electrical potential as the liquid being measured.
This is achieved by means of built-in grounding electrodes.
Figure 4-10 Potential equalization with earthing electrodes
Cathodic protected piping
Special attention must be paid to systems with cathodic protection
WARNING
Use in hazardous area!
Cathodic pipe protection is not allowed in hazardous areas
Installing/Mounting
4.5 Potential equalization
SITRANS F M MAG 5100 W
22 Operating Instructions, 11/2010, A5E03063678-02
Figure 4-11 Cathodic protection
● Isolate the sensor from cathodic protected pipes using insulated bolts.
● Use bypass cable between the mating flanges
NOTICE
Remote mounted sensor versions
If the above is not acceptable, remote mounted sensors can alternatively be connected
as follows:
Connect coil current cable shield at sensor end via a 1.5 µF condensator
Make sure that electrode cable shield is not connected at both ends
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 23
5
Connecting
The following contains a short description of how to connect a remote mounted sensor to a
transmitter type SITRANS F M MAG 5000 / 6000 or MAG 6000 I. For more information, e.g.
about wiring of power supply and outputs, refer to the Operating Instructions for the
respective transmitters.
Before connecting
● Check that serial numbers on sensor and SENSORPROM® unit are identical.
WARNING
The pertinent regulations must be observed for electrical installation.
Never install the device with the mains voltage switched on!
Danger of electric shock!
The electrodes and magnetic current line may only be connected when the device is not
connected to the power supply.
If the housing is under voltage (power supply), the cover may be unscrewed by qualified
personnel only.
WARNING
Mains supply from building installation Class II
A switch or circuit breaker (max. 15 A) must be installed in close proximity to the equipment
and within easy reach of the operator. It must be marked as the disconnecting device for
the equipment.
Cable specifications
● Only use cables with at least the same degree of protection as the sensor to install the
sensor.
● The line length from the cable gland to the terminals must be kept as short as possible.
Line loops in the terminal box must be avoided.
Connecting
5.1 Remote installation
SITRANS F M MAG 5100 W
24 Operating Instructions, 11/2010, A5E03063678-02
● To guarantee the IP 67 degree of protection, use cables with the required specifications.
WARNING
Protective conductor terminal
The required cable is min. AGW16 or 1.5 Cu.
WARNING
Wire insulation
The insulation between the connected mains supply and 24 V AC/DC supply for the
flowmeter must at least be rated with double or reinforced insulation at mains voltage.
For field wiring installation: Ensure that the National Installation Code of the country in
which the flowmeters are installed is met.
See also
Cable data (Page 40)
5.1 Remote installation
NOTICE
Remote installation only
The following applies to remote installation of MAG 5000 / 6000 or MAG 6000 I.
1. Unscrew and remove terminal box lid.
Connecting
5.1 Remote installation
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 25
2. Remove SENSORPROM® unit from sensor and mount it on connection plate in
transmitter, see relevant transmitter operating instructions.
3. Fit the ½" NPT or M20 cable glands for supply and output cables.
4. Fit and connect electrode and coil cables as shown below.
6KLHOG
CAUTION
Unshielded cable ends
Keep unscreened cable ends as short as possible.
CAUTION
Prevent interference
Separate electrode and coil cables to prevent interference.
Connecting
5.2 Installation check
SITRANS F M MAG 5100 W
26 Operating Instructions, 11/2010, A5E03063678-02
5. Tighten cable glands well to obtain optimum sealing.
WARNING
Mount terminal box lid before power up.
5.2 Installation check
The meter is now ready to go into normal operation - for commissioning and setting of
parameters refer to the relevant transmitter manual.
Before commissioning it must be checked that:
● The device has been installed and connected in accordance with the guidelines provided
in chapter 4 Installing/mounting (Page 15) and 5 Connecting (Page 23)
5.3 Potting
If sensor is buried or permanently submerged, terminal box must be encapsulated with
silicon dielectric gel (non-toxic, transparent and self-healing gel)
CAUTION
Do not pot meter before electrical connections have been made.
● Mix the two components of the potting kit well and pour into terminal box.
● Let cure for approximately 24 hours at approximately 25°C (77°F). Curing time increases
by 100% per -10°C (-18°F).
Connecting
5.3 Potting
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 27
Horizontal orientation Vertical orientation
NOTICE
Gel can be penetrated with test instruments or be removed in case of cable replacement.
Connecting
5.4 Direct burial
SITRANS F M MAG 5100 W
28 Operating Instructions, 11/2010, A5E03063678-02
5.4 Direct burial
Recommendations for direct burial of remote sensor:
● Check for visible damages in paint finish !
● Use protection conduit !
● Protect sensor with pea gravel at least 3000 mm around sensor. This provides some
drainage and also avoids caking sensor with earth. It also helps to locate sensor in case
excavation takes place.
Figure 5-1 Direct burial of sensor
CAUTION
Sensor should not be subject to heavy vehicles applying excessive weight above sensor
or pipeline
CAUTION
SENSORPROM® memory unit
Remove the SENSORPROM® from terminal box on sensor and relocate in remote
transmitter prior to burying sensor.
All sensor data plate information and serial number should be recorded for each sensor
prior to burying. This will ensure correct matching with SENSORPROM® unit.
WARNING
Electrical cable identification
Use suitable coil and electrode cables
Lay electrical cable identification tape above pea gravel before it is covered with earth.
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 29
6
Service and maintenance
6.1 Maintenance
The device is maintenance-free, however, a periodic inspection according pertinent
directives and regulations must be carried out.
An inspection can include check of:
● Ambient conditions
● Seal integrity of the process connections, cable entries, and cover screws
● Reliability of power supply, lightning protection, and grounds
6.2 Recalibration
Siemens A/S Flow Instruments offers to recalibrate the sensor. The following calibrations are
offered as standard:
● Standard matched pair calibration
Note
For recalibration the memory unit must always be returned with the sensor
6.3 Transportation/storage
The sensor is a fragile piece of equipment. Impact and shock can
cause measuring inaccuracy. Therefore during transportation it must
be placed in the transportation box delivered by Siemens Flow
Instruments. If this is not possible, the alternative sensor packaging
must be able to withstand the hazards from transportation.
Service and maintenance
6.4 Unit repair
SITRANS F M MAG 5100 W
30 Operating Instructions, 11/2010, A5E03063678-02
Handling
Figure 6-1 Handling of sensor
6.4 Unit repair
CAUTION
Repair and service must be carried out by Siemens authorized personnel only.
Note
Siemens Flow Instruments defines sensors as non-repairable products.
6.5 Technical support
If you have any technical questions about the device described in these Operating
Instructions and do not find the right answers, you can contact Technical Support:
● Via the Internet using the Support Request:
Support request (http://www.siemens.com/automation/support-request)
● Via Phone:
– Europe: +49 (0)911 895 7222
– America: +1 423 262 5710
– Asia-Pacific: +86 10 6475 7575
Further information about our technical support is available in the Internet at
Technical support (http://support.automation.siemens.com/WW/view/en/16604318)
Service and maintenance
6.6 Return procedures
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 31
Service & Support on the Internet
In addition to our documentation, we offer a comprehensive knowledge base online on the
Internet at:
Service and support (http://www.siemens.com/automation/service&support)
There you will find:
● The latest product information, FAQs, downloads, tips and tricks.
● Our newsletter, providing you with the latest information about your products.
● A Knowledge Manager to find the right documents for you.
● Our bulletin board, where users and specialists share their knowledge worldwide.
● You can find your local contact partner for Industry Automation and Drives Technologies
in our partner database.
● Information about field service, repairs, spare parts and lots more under "Services."
Additional Support
Please contact your local Siemens representative and offices if you have additional
questions about the device
Find your contact partner at:
Local contact person (http://www.automation.siemens.com/partner)
6.6 Return procedures
Enclose the delivery note, the cover note for return delivery together with the declaration of
decontamination form on the outside of the package in a well-fastened clear document
pouch.
Required forms
● Delivery Note
● Cover Note for Return Delivery with the following information
Cover note (http://support.automation.siemens.com/WW/view/en/16604370)
– product (ordering number)
– number of devices or spare parts returned
– reason for the return
Service and maintenance
6.6 Return procedures
SITRANS F M MAG 5100 W
32 Operating Instructions, 11/2010, A5E03063678-02
● Declaration of Decontamination
Declaration of Decontamination
(http://pia.khe.siemens.com/efiles/feldg/files/Service/declaration_of_decontamination_en.
pdf)
With this declaration you certify
that the returned products/spare parts have been
carefully cleaned and are free from any residues.
If the device has been operated together with toxic, caustic, flammable or water-
damaging products, clean the device before return by rinsing or neutralizing. Ensure that
all cavities are free from dangerous substances. Then, double-check the device to ensure
the cleaning is completed.
We shall not service a device or spare part unless the declaration of decontamination
confirms proper decontamination of the device or spare part. Shipments without a
declaration of decontamination shall be cleaned professionally at your expense before
further proceeding.
You can find the forms on the Internet and on the CD delivered with the device.
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 33
Troubleshooting/FAQs 7
7.1 Sensor check
Requirement
To check the SITRANS F M sensors the following test instruments will be required:
● Digital Meter/Multimeter
● Megger
● (Moving Coil Meter)
Sensor check
Remove the transmitter from the sensor or remote position before making the following
checks.
Coil resistance check
● Measure the coil resistance between connection numbers 85 and 86 using a digital
meter.
Resistance should be around 100 ohms ±10 ohms. (See Coil resistence table)
A low reading may indicate moisture within the coil housing or shorted coil tums.
A high reading would indicate an open circuit coil.
NOTICE
In case of deviation from nominal coil values, the sensor is damaged and must be replaced
Coil insulation check
WARNING
Potential hazard!
Only carry our a coil insulation check in non-hazardous area!
● Megger between connection number 85 and the sensor body.
The resistance should be above 20 Megohms.
A low megger reading would indicate the coil insulation is braking down. This is normally due
to fluid ingress into the coil housing.
Troubleshooting/FAQs
7.1 Sensor check
SITRANS F M MAG 5100 W
34 Operating Instructions, 11/2010, A5E03063678-02
Sensors with an insulation resistance down to 1 Megohms may still work satisfactorily but
this is not guaranteed.
Electrode resistance check
● Measure the electrode resistance between connections 82 and Zero with a moving coil
meter.
With a sensor full of fluid the resistance should be between 5Kohms and 50Kohms.
If the sensor is empty the resistance will be infinite.
● Repeat the resistance measurements between connections 83 and Zero.
The results should be the same.
If the resistance is low there may be a short on the electrodes or wiring (in the case of a
remote mounted transmitter). Alternatively there may be water ingress or moisture in the
terminal box.
If the resistance is high and the pipe is completely full of fluid check the following:
1. The fluid is electrically conductive.
2. Electrodes are not coated with grease or any deposit.
3. Electrode circuit is not open
4. The remote mounted transmitter has a 3 core cable with an overall shield continuously
from the sensor to the transmitter, including junction boxes and terminal rails inside
panels.
5. The shield is connected to the Zero or to the earth terminal (PE) on the sensor.
NOTICE
Sensors removed from line
For sensors removed from line with dry bore, use megger between terminal 82 and
compression plate, and 83 and compression plate to show any water ingress behind
electrodes or within enclosure.
Troubleshooting/FAQs
7.2 Fluctuating process values
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 35
7.2 Fluctuating process values
Question
Why do the displayed process values fluctuate when the electrode cable is moved?
Answer
There are several causes to the fluctuating process values:
● Deposits on electrodes
– Clean the electrodes.
● Defect electrode cable
– Replace the cable
● Incorrect cable connection
– Connect the electrode cable (82, 83, 0 and shield) according to the instructions in
chapter Connecting (Page 23)
NOTICE
Vibrating environments
It is recommended to use special low noise cables for sensor sizes DN 2 and 3
installed in vibrating environments.
Troubleshooting/FAQs
7.2 Fluctuating process values
SITRANS F M MAG 5100 W
36 Operating Instructions, 11/2010, A5E03063678-02
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 37
Technical data 8
8.1 MAG 5100 W
Table 8- 1 Technical data
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
Product characteristic Mainly for the European market
EPDM or NBR lining
Mainly for the non-European market
Ebonite lining
Design and nominal size
Coned sensor:
DN 15 ... 300 (½" ... 12")
Full bore sensor:
DN 350 ... 1200 (14" ... 48")
Full bore sensor:
DN 25 ... 2000 (1" ... 78")
Measuring principle Electromagnetic induction
Excitation frequency
(Mains supply: 50 Hz/60 Hz)
DN 15 ... 65 (½" ... 2½"):
12.5 Hz / 15 Hz
DN 80 ... 150 (3" ... 6"):
6.25 Hz / 7.5 Hz
DN 200 ... 300 (8" ... 12"):
3.125 Hz / 3.75 Hz
DN 350 ... 1200 (14" ... 48"):
1.5625 Hz / 1.875 Hz
DN 25 ... 65 (1" ... 2½"):
12.5 Hz / 15 Hz
DN 80 ... 150 (3" ... 6"):
6.25 Hz / 7.5 Hz
DN 200 ... 1200 (8" ... 48"):
3.125 Hz / 3.75 Hz
DN 1400 ... 2000 (54" ... 78"):
1.5625 Hz / 1.875 Hz
Table 8- 2 Process connections
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
EN 1092-1
PN 10 (145 psi):
DN 200 ... 300 (8" ... 12")
Flat face flanges
PN 10 (145 psi):
DN 350 ... 1200 (14" ... 48")
Raised face flanges
PN 16 (232 psi):
DN 50 ... 300 (2" ... 12")
Flat face flanges
PN 16 (232 psi):
DN 350 ... 1200 (14" ... 48")
Raised face flanges
PN 40 (580 psi):
DN 15 ... 40 (½" ... 1½")
Flat face flanges
Raised face
(EN 1092-1, DIN 3501 and BS4504
have the same mating dimensions)
PN 16 (87 psi):
DN 1400 ... 2000 (54" ... 78")
PN 10 (145 psi):
DN 200 ... 2000 (8" ... 78")
PN16 (232 psi):
DN 65 ... 600 (2½" ... 24")
PN 40 (580 psi):
DN 25 ... 50 (1" ... 2")
ANSI B16.5 Class 150 lb: ½" ... 24" Class 150 lb: 1" ... 24"
Technical data
8.1 MAG 5100 W
SITRANS F M MAG 5100 W
38 Operating Instructions, 11/2010, A5E03063678-02
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
AWWA C-207 Class D:
28" ... 48", Flat face flanges
Class D:
28" ... 78", Flat face flanges
AS4087
PN 16 (230 psi):
DN 50 ... 1200 (2" ... 48")
PN 16 (230 psi):
DN 50 ... 1200 (2" ... 48")
JIS B 2220:2004 - K10 (1" ... 24")
Table 8- 3 Rated operating conditions
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
Ambient temperature
Sensor
-40 ... +70 °C (-40 ... +158 °F) -40 ... +70 °C (-40 ... +158 °F)
With compact transmitter
MAG 5000/6000 -20 ... +60 °C (-4 ... +140 °F) -20 ... +60 °C (-4 ... +140 °F)
MAG 6000 I -20 ... +60 °C (-4 ... +140 °F) -20 ... +60 °C (-4 ... +140 °F)
Operating pressure [abs. bar]1 DN 15 ... 40 (½" ... 1½")
0.01 ... 40 bar (0.15 ... 580 psi)
DN 50 ... 300 (2" ... 12")
0.03 ... 20 bar (0.44 ... 290 psi)
DN 350 ... 1200 (14" ... 48")
0.01 ... 16 bar (0.15 ... 232 psi)
DN 25 ... 50 (1" ... 2")
0.01 ... 40 bar (0.15 ... 580 psi)
DN 65 ... 1200 (2½" ... 48")
0.01 ... 16 bar (0.15 ... 232 psi)
DN 1400 ... 2000 (54" ... 78")
0.01 ... 10 bar (0.15 ... 145 psi)
Enclosure rating
Standard IP67 to EN 60529 / NEMA 4X/6 (1
mH2O for 30 minutes)
IP67 to EN 60529 / NEMA 4X/6 (1
mH2O for 30 minutes)
Option IP68 to EN 60529 / NEMA 6P (10
mH2O continuously)
IP68 to EN 60529 / NEMA 6P (10
mH2O continuously)
Corrosive category C4 according to ISO 12944-2 C4 according to ISO 12944-2
Pressure drop DN 15 and 25 (½" and 1"):
Max. 20 mbar (0.29 psi) at 1 m/s (3
ft/s)
DN 40 ... 300 (1½" ... 12"):
Max. 25 mbar (0.36 psi) at 3 m/s
(10ft/s)
DN 350 ... 1200 (14" ... 48"):
Insginificant
Insignificant
Test pressure 1.5 x PN (where applicable) 1.5 x PN (where applicable)
Mechanical load (vibration) 18 ... 1000 Hz random in x,y, z
directions for 2 hours according to EN
60068-2-36
Sensor: 3.17 grms
Sensor with compact MAG 5000/6000
transmittter mounted: 3.17 grms
Sensor with compact MAG 6000 I
transmitter mounted: 1.14 grms
18 ... 1000 Hz random in x,y, z
directions for 2 hours according to EN
60068-2-36
Sensor: 3.17 grms
Sensor with compact MAG 5000/6000
transmittter mounted: 3.17 grms
Sensor with compact MAG 6000 I
transmitter mounted: 1.14 grms
Technical data
8.1 MAG 5100 W
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 39
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
Process fluid temperature
NBR
-10 ... +70 °C (14 ... 158 °F) -
EPDM
-10 ... +70 °C (14 ... 158 °F) -
EPDM (MI-001)
+0.1 ... +30 °C (32 ... 76 °C) -
Ebonite
- -10 ... +70 °C (14 ... 158 °F)
EMC EMC 2004/108/EC EMC 2004/108/EC
Maximum operating pressure decreases with increasing operating temperature
Table 8- 4 Design
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
Housing and flange material Carbon steel, with corrosion-resistant
two-component epoxy coating (min.
150 µm)
Corrosive category C4, according to
ISO 12944-2
Carbon steel ASTM A 105, with
corrosion-resistant two-component
epoxy coating (min. 150 µm)
Measuring pipe AISI 304 (1.4301) AISI 304 (1.4301)
Electrodes Hastelloy Hastelloy
Grounding electrodes (standard Hastelloy Hastelloy
Terminal box Fibre glass reinforced polyamide Fibre glass reinforced polyamide
Table 8- 5 Certificates and approvals
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
Calibration
Standard production calibration,
calibration report shipped with sensor
DN 15 ... 300:
Zero-point, 2 x 25 % and 2 x 90 %
DN 350 ... 1200:
Zero-point, 1 x 25 % and 1 x 90 %
Zero-point, 2 x 25 % and 2 x 90 %
Custody transfer (only with MAG
5000/6000 CT)
OIML R 49 pattern approval cold water
(Denmark and Germany):
DN 50 ... 300 (2" ... 12")
MI 001 cold water (EU):
DN 50 ... 300 (2" ... 12")
-
Technical data
8.2 Cable data
SITRANS F M MAG 5100 W
40 Operating Instructions, 11/2010, A5E03063678-02
Version MAG 5100W (7ME6520) MAG 5100W (7ME6580)
Drinking water approvals
EPDM liner:
ANSI/NSF 61 Standard (Cold water,
US)
WRAS (WRc, BS6920 cold water,
GB)
ACS (F)
DVGW W270 (D)
Belgaqua (NBR)
NBR liner:
ANSI/NSF 61 Standard (Cold water,
US), only ANSI and AWWA flanges)
NSF/ANSI Standard 61 (Cold water,
US)
WRAS (WRc, BS6920 cold water,
GB)
Other approvals MCERTS
PED - 97/23 EC1), CRN
FM Class 1, Div 2
CSA Class 1, Div 2
PED - 97/23 EC1) (only < DN 600 (<
24"))
FM Class 1, Div 2
CSA Class 1, Div 2
1) : For sizes larger than 600 mm (24") in PN 16, PED conformity is available as cost-added option. The basic unit will
carry the LVD (Low Voltage Directive) and EMC approval.
8.2 Cable data
Description
Cable for standard electrode or coil
Electrode cable, double shielded
Cable kit with standard coil cable and electrode cable double
shielded (also available as low noise cable for MAG 1100
sensor )
Standard applications
Table 8- 6 Technical data, standard application cables
Coil cable Standard electrode
cable
No. of conductors 2 3
Min. sqr. area
Basic data
0.5 mm2 0.2 mm2
Shield Yes Yes
Max. capacitance N/A 350 pF/m
Technical data
8.3 Effect of temperature on working pressure
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 41
Coil cable Standard electrode
cable
Media temperature:
< 100 °C 40 Ω N/A
Max. cable loop resistance
> 200 °C 6 Ω N/A
M20x1.5 gland - Cable ø 5 ... 13 mm (0.20 ... 0.51 inches) Cable glands on sensor
and transmitter ½ NPT gland - cable ø 5 ... 9 mm (0.20 ... 0.35 inches)
Special applications, e.g. low conductivity or electrical noise
Table 8- 7 Technical data, special application cables
Coil cable Special electrode cable
No. of conductors 3 3
Sqr. area 1.5 mm2 0.25 mm2
Shield Yes Double
Color code Brown, blue, black Brown, blue, black
Outside color Grey Grey
Ext. diameter 7.8 mm 8.1 mm
Conductor Flexible CU Flexible CU
Basic data
Isolation material PVC PVC
Flexible installation -5 ... +70°C
(23 ... 158°F)
-5 ... +70°C
(23 ... 158°F)
Ambient temperature
Non-flexible installtaion -30 ... +70°C
(-22 ... 158°F)
-30 ... +70°C
(-22 ... 158°F)
Capacity 161.50 pF/m N/A
Inductance 0.583 μH/m N/A
Cable parameter
L/R 43.83 þH/Ω N/A
8.3 Effect of temperature on working pressure
Effect of temperature on working pressure.
Table 8- 8 Metric measures (pressure in bar)
Temperature (°C)
Flange
specifications
Flange rating
-5 10 50 90
Sizes DN25 ... 2000
PN 10 10.0 10.0 9.7 9.4
PN 16 16.0 16.0 15.5 15.1
EN 1092-1
PN 40 40.0 40.0 38.7 37.7
ANSI B16.5 150 lb 19.7 19.7 19.3 18.0
AWWA C-207 Class D 10.3 10.3 10.3 10.3
Technical data
8.4 Process fluid conductivity
SITRANS F M MAG 5100 W
42 Operating Instructions, 11/2010, A5E03063678-02
Temperature (°C) Flange
specifications
Flange rating
-5 10 50 90
Sizes DN 15 ... 300 (order no. 7ME6520 only)
PN 10 10.0 10.0 10.0 8.2
PN 16 10.0 16.0 16.0 13.2
EN 1092-1
PN 40 40.0 40.0 38.7 37.7
ANSI B16.5 150 lb 10.0 19.7 19.7 16.2
Table 8- 9 Imperial measures (pressure in psi)
Temperature (°F)
Flange
specifications
Flange rating
23 50 120 200
Sizes 1" ... 78"
PN 10 145 145 141 136
PN 16 232 232 225 219
EN 1092-1
PN 40 580 580 561 547
ANSI B16.5 150 lb 286 286 280 261
AWWA C-207 Class D 150 150 150 150l
Sizes ½"... 12" (order no. 7ME6520 only)
PN 10 145 145 145 119 EN 1092-1
PN 16 145 232 232 191
ANSI B16.5 150 lb 145 286 286 235
8.4 Process fluid conductivity
Compact installation
Liquids with an electrical conductivity ≥ 5 μS/cm.
Remote installation
Standard cable
Cabel length
Conductivity
of medium
[µS/cm]
[m]
300
200
1005
300
200
100
5
150 600 900 [ft]
300
Technical data
8.5 Liner selection
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 43
[µS/cm]
50
40
20
5
30
10
50 300 400 500 [m]
100 200
[ft]
15001200900
150 300 600
Conductivity
of medium
Special cable
Cable length
WARNING
For detection of empty sensor the min. conductivity must always be >50 μS/cm and the
max. length of the electrode cable when remote mounted is 50 meters (164 ft). Special
cable must be used!
For remote MID installations the max. cable length is 3 meters (9.8 ft). For other CT
application standard requirements are applicable.
8.5 Liner selection
Liner Applications
EPDM Drinking water applications (not hydrocarbons)
Ebonite Drinking water applications wastewater applications and
certain chemicals applications
NBR General purpose. Drinking water, sea waters
8.6 Electrode selection
Electrodes
Hastelloy C The preferred choice for water and wastewater, chemicals,
food and beverage, and pharmaceutical industries
Technical data
8.7 Sizing tables
SITRANS F M MAG 5100 W
44 Operating Instructions, 11/2010, A5E03063678-02
8.7 Sizing tables
Sizing table (DN 2 ... DN 2000)
Technical data
8.7 Sizing tables
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 45
Sizing table (DN 1/12" ... DN 78")
The tables show the relationship between flow velocity v, flow quantity Q and sensor
dimension DN.
Guidelines for selection of sensor
Min. measuring range: 0 ... 0.25 m/s (0 ... 0.8 ft/s)
Max. measuring range: 0 ... 10 m/s (0 ... ft/s)
Normally the sensor size is selected so that the nominal flow velocity v lies within the
measuring range 1 ... 3 m/s (1 ... 15 ft/s).
Technical data
8.8 Dimensions and weight
SITRANS F M MAG 5100 W
46 Operating Instructions, 11/2010, A5E03063678-02
Flow velocity calculation formula:
(metric measures)
1273.24 x Q [l/s]
DN
2
[mm] [m/s] or V =V = 353.68 x Q [m
3
/h]
DN
2
[mm] [m/s]
(imperial measures)
0.408 x Q [GPM]
(Pipe ID)
2
[inch] [ft/s] or V =V = 283.67 x Q [MGD]
(Pipe ID)
2
[inch] [ft/s]
8.8 Dimensions and weight
83N58.11
$
$
//
$
$
/
$
$
83N58.11
[0
0
ರ137
[0
[0
0
ರ137
0
ರ137
Figure 8-1 MAG 5100 W with MAG 6000 I / MAG 6000 I Ex d
/
$
$
/
$
/
$
$
$
0
ರ137
0
ರ137
0
ರ137
Figure 8-2 MAG 5100 W with MAG 5000 / 6000
Technical data
8.8 Dimensions and weight
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 47
Dimensions
Table 8- 10 Nominal size A
A
Nominal size
Order no.
7ME6520 NBR or EPDM liner
Order no.
7ME6580 Ebonite liner
mm inch mm inch mm inch
15 ½ 177 7 - -
25 1 187 7.4 187 7.4
40 1½ 202 8 197 7.8
50 2 188 7.4 205 8.1
65 2½ 194 7.6 212 8.3
80 3 200 7.9 222 8.7
100 4 207 8.1 242 9.5
125 5 217 8.5 255 10.0
150 6 232 9.1 276 10.9
200 8 257 10.1 304 12.0
250 10 284 11.2 332 13.1
300 12 310 12.2 357 14.1
350 14 382 15.0 362 14.3
400 16 407 16.0 387 15.2
450 18 438 17.2 418 16.5
500 20 463 18.2 443 17.4
600 24 514 20.2 494 19.4
700 28 564 22.2 544 21.4
750 30 591 23.3 571 22.5
800 32 616 24.3 606 23.9
900 36 663 26.1 653 25.7
1000 40 714 28.1 704 27.7
1050 42 714 28.1 704 27.7
1100 44 765 30.1 755 29.7
1200 48 820 32.3 810 31.9
1400 54 N/A N/A 925 36.4
1500 60 N/A N/A 972 38.2
1600 66 N/A N/A 1025 40.4
1800 72 N/A N/A 1123 44.2
2000 78 N/A N/A 1223 48.1
Technical data
8.8 Dimensions and weight
SITRANS F M MAG 5100 W
48 Operating Instructions, 11/2010, A5E03063678-02
Table 8- 11 Nominal size L
L
Nominal size
PN 10 PN 16 PN 16
non-PED
PN 40 Class 150
AWWA
AS / JIS10K
mm inch mm inch mm inch mm inch mm inch mm inch mm inch
15 ½ N/A N/A N/A N/A N/A N/A 200 7.9 200 7.9 N/A N/A
25 1 N/A N/A N/A N/A N/A N/A 200 7.9 200 7.9 200 7.9
40 1½ N/A N/A N/A N/A N/A N/A 200 7.9 200 7.9 200 7.9
50 2 N/A N/A 200 7.9 N/A N/A N/A N/A 200 7.9 200 7.9
65 2½ N/A N/A 200 7.9 N/A N/A N/A N/A 200 7.9 200 7.9
80 3 N/A N/A 200 7.9 N/A N/A N/A N/A 200 7.9 200 7.9
100 4 N/A N/A 250 9.8 N/A N/A N/A N/A 250 9.8 250 9.8
125 5 N/A N/A 250 9.8 N/A N/A N/A N/A 250 9.8 2501) 9.8
1)
150 6 N/A N/A 300 11.8 N/A N/A N/A N/A 300 11.8 300 11.8
200 8 350 13.8 350 13.8 N/A N/A N/A N/A 350 13.8 350 13.8
250 10 450 17.7 450 17.7 N/A N/A N/A N/A 450 17.7 450 17.7
300 12 500 19.7 500 19.7 N/A N/A N/A N/A 500 19.7 500 19.7
350 14 550 21.7 550 21.7 N/A N/A N/A N/A 550 21.7 550 21.7
400 16 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 N/A 23.6
450 18 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 600 23.6
500 20 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 600 23.6
600 24 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 600 23.6
700 28 700 27.6 700 27.6 N/A N/A N/A N/A 700 27.6 7002) 27.62)
750 30 N/A N/A N/A N/A N/A N/A N/A N/A 750 29.5 7502) N/A
800 32 800 31.5 800 31.5 N/A N/A N/A N/A 800 31.5 8002) 31.52)
900 36 900 35.4 900 35.4 N/A N/A N/A N/A 900 35.4 9002) 35.42)
1000 40 1000 39.4 1000 39.4 N/A N/A N/A N/A 1000 39.4 10002) 39.42)
1050 42 N/A N/A N/A N/A N/A N/A N/A N/A 1000 39.4 N/A N/A
1100 44 N/A N/A N/A N/A N/A N/A N/A N/A 1100 43.3 N/A N/A
1200 48 1200 47.2 1200 47.2 N/A N/A N/A N/A 1200 47.2 12002) 47.22)
1400 54 1400 55.1 N/A N/A 1400 55.1 N/A N/A 1200 47.2 N/A N/A
1500 60 1500 59.1 N/A N/A 1500 59.1 N/A N/A 1200 47.2 N/A N/A
1600 66 1600 63.0 N/A N/A 1600 63.0 N/A N/A 1200 47.2 N/A N/A
1800 72 1800 70.9 N/A N/A 1800 70.9 N/A N/A 1200 47.2 N/A N/A
2000 78 2000 78.7 N/A N/A 2000 78.7 N/A N/A 1200 47.2 N/A N/A
1) Not available with AS flange
2) Not available with JIS 10K flange
Technical data
8.8 Dimensions and weight
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 49
Weight
Table 8- 12 Weight
Order no.
7ME6520
Order no.
7ME6580
Nominal size
PN 10 PN 16 PN 40 Class 150 /
AWWA
AS PN / ANSI /
AWWA / AS
mm inch kg lbs kg lbs kg lbs kg lbs kg lbs kg lbs
15 ½ N/A N/A N/A N/A 4 9 4 9 N/A N/A - -
25 1 N/A N/A N/A N/A 6 12 5 11 N/A N/A 5 11
40 1½ N/A N/A N/A N/A 8 18 7 15 N/A N/A 8 17
50 2 N/A N/A 9 20 N/A N/A 8 20 N/A N/A 9 20
65 2½ N/A N/A 10.7 24 N/A N/A 11 24 N/A N/A 11 24
80 3 N/A N/A 11.6 26 N/A N/A 13 28 N/A N/A 12 24
100 4 N/A N/A 15.2 33 N/A N/A 19 41 N/A N/A 16 35
125 5 N/A N/A 20.4 45 N/A N/A 24 52 N/A N/A 19 42
150 6 N/A N/A 26 57 N/A N/A 29 64 N/A N/A 27 60
200 8 48 106 48 106 N/A N/A 56 124 N/A N/A 40 68
250 10 64 141 69 152 N/A N/A 79 174 N/A N/A 60 132
300 12 76 167 86 189 N/A N/A 110 243 N/A N/A 80 176
350 14 104 229 125 274 N/A N/A 139 307 N/A N/A 110 242
400 16 119 263 143 314 N/A N/A 159 351 N/A N/A 125 275
450 18 136 299 173 381 N/A N/A 182 400 N/A N/A 175 385
500 20 163 359 223 491 N/A N/A 225 495 N/A N/A 200 440
600 24 236 519 338 744 N/A N/A 320 704 N/A N/A 187 633
700 28 270 595 314 692 N/A N/A 273 602 320 70 330 728
750 30 N/A N/A N/A N/A N/A N/A 329 725 N/A N/A 360 794
800 32 346 763 396 873 N/A N/A 365 804 428 944 450 992
900 36 432 951 474 1043 N/A N/A 495 1089 618 1362 53 1168
1000 40 513 1130 600 1321 N/A N/A 583 1282 636 1399 66 1455
1050 42 N/A N/A N/A N/A N/A N/A 687 1512 N/A N/A N/A N/A
1100 44 N/A N/A N/A N/A N/A N/A 763 1680 N/A N/A 1140 2513
1200 48 643 1415 885 1948 N/A N/A 861 1896 813 1789 1180 2601
1400 54 1592 3510 N/A N/A N/A N/A N/A N/A N/A N/A 1600 3528
1500 60 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 2460 5423
1600 66 2110 4652 N/A N/A N/A N/A N/A N/A N/A N/A 2525 5566
1800 72 2560 5644 N/A N/A N/A N/A N/A N/A N/A N/A 2930 6460
2000 78 3640 8025 N/A N/A N/A N/A N/A N/A N/A N/A 3665 8080
Technical data
8.8 Dimensions and weight
SITRANS F M MAG 5100 W
50 Operating Instructions, 11/2010, A5E03063678-02
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 51
A
Appendix
A.1 Flange mating dimensions (metric)
Figure A-1 Flange mating dimensions
Table A- 1 Flange mating dimensions (metric)
Dimensions (mm) Bolting
mm D PCD T B Holes Bolts
PN10
200 340 295 24 22 8 M20
250 395 350 26 22 12 M20
300 445 400 26 22 12 M20
350 505 460 28 22 16 M20
400 565 515 32 26 16 M24
450 615 565 36 26 20 M24
500 670 620 38 26 20 M24
600 780 725 42 3 20 M27
700 895 840 30 30 24 M27
800 1015 950 32 33 24 M30
900 1115 1050 34 33 28 M30
1000 1230 1160 34 36 28 M33
1200 1455 1380 38 39 32 M36
PN16
50 165 125 19 18 4 M16
65 185 145 20 18 8 M16
80 200 160 20 18 8 M16
100 220 180 22 18 8 M16
125 250 210 22 18 8 M16
150 285 240 24 22 8 M20
200 340 295 26 22 12 M20
250 405 355 29 26 12 M24
Appendix
A.1 Flange mating dimensions (metric)
SITRANS F M MAG 5100 W
52 Operating Instructions, 11/2010, A5E03063678-02
Dimensions (mm) Bolting
mm D PCD T B Holes Bolts
300 460 410 32 26 12 M24
350 520 470 35 26 16 M24
400 580 525 38 30 16 M27
450 640 585 42 30 20 M27
500 715 650 46 33 20 M30
600 840 770 52 36 20 M33
700 910 840 36 36 24 M33
800 1025 950 38 39 24 M36
900 1125 1050 40 39 28 M36
1000 1255 1170 42 42 28 M39
1200 1485 1390 48 48 32 M45
PN40
15 95 65 14 14 4 M12
25 115 85 16 14 4 M16
40 150 110 18 18 4 M16
150 lb
15 89 60 12 16 4 M12
25 108 79 16 16 4 M16
40 127 98 18 16 4 M16
50 152 121 19 19 4 M16
65 178 140 22 19 4 M16
80 190 152 24 19 4 M16
100 229 191 24 19 8 M16
125 254 216 24 22 8 M20
150 279 241 25 22 8 M20
200 343 298 29 22 8 M20
250 406 362 30 25 12 M24
300 483 432 32 25 12 M24
350 533 476 35 28 12 M27
400 597 540 36.5 28 16 M27
450 635 578 40 32 16 M30
500 699 635 43 32 20 M30
600 813 749 48 35 20 M33
Appendix
A.2 Factory settings
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 53
Dimensions (mm) Bolting
mm D PCD T B Holes Bolts
AWWA
700 927 864 33 35 28 M33
750 984 914 35 35 28 M33
800 1060 978 38 41 28 M39
900 1168 1068 41 41 32 M39
1000 1289 1200 41 41 36 M39
1050 1346 1257 44 41 36 M39
1200 1511 1422 48 41 44 M39
A.2 Factory settings
Dimension-dependent factory settings
Table A- 2 50 Hz version
Qmax
DN
Order no. 7ME6520 Order no. 7ME6580
Unit Volume/
pulse
Pulse
unit
Totalizer
unit
mm Inch Fac
settings
Min. Max. Min. Max.
15 ½ 2000 159 6361 - - l/h 1 l l
25 1 5000 441 17671 441 17671 l/h 10 l l
40 1½ 12 1.1 45 1.1 45 m3/h 10 l l
50 2 20 1.7 63 1.7 70 m3/h 10 l l
65 2½ 30 2.9 100 2.9 119 m3/h 100 l l
80 3 50 4.0 160 4.5 180 m3/h 100 l l
100 4 120 6.2 250 7 282 m3/h 100 l l
125 5 180 10.0 400 11 441 m3/h 100 l m3
150 6 250 15.7 629 15.9 636 m3/h 100 l m3
200 8 400 24.9 997 28.2 1130 m3/h 1 m3 m
3
250 10 700 40.0 1600 44.1 1767 m3/h 1 m3 m
3
300 12 1000 62.5 2500 63.6 2544 m3/h 1 m3 m
3
350 14 1200 86.5 3463 86.5 3463 m3/h 1 m3 m
3
400 16 1800 113 4523 113 4523 m3/h 1 m3 m
3
450 18 2000 143.1 5725 143.1 5725 m3/h 1 m3 m
3
500 20 3000 176.7 7068 176.7 7068 m3/h 1 m3 m
3
600 24 4000 254.4 10178 254.4 10178 m3/h 10 m3 m
3
700 28 5000 346.3 13854 346.3 13854 m3/h 10 m3 m
3
750 30 6000 397.6 15904 397.6 15904 m3/h 10 m3 m
3
800 32 7000 452.3 18095 452.3 18095 m3/h 10 m3 m
3
Appendix
A.2 Factory settings
SITRANS F M MAG 5100 W
54 Operating Instructions, 11/2010, A5E03063678-02
Qmax DN
Order no. 7ME6520 Order no. 7ME6580
Unit Volume/
pulse
Pulse
unit
Totalizer
unit
900 36 9000 572.5 22902 572.5 22902 m3/h 10 m3 m
3
1000 40 12000 706.8 28274 706.8 28274 m3/h 10 m3 m
3
1050 42 12000 706.8 28274 706.8 28274 m3/h 10 m3 m
3
1100 44 14000 855.2 34211 855.2 34211 m3/h 10 m3 m
3
1200 48 15000 1017.8 40715 1017.8 40715 m3/h 10 m3 m
3
1400 54 25000 - - 1385.4 55417 m3/h 10 m3 m
3
1500 60 30000 - - 1590.4 63617 m3/h 10 m3 m
3
1600 66 35000 - - 1809.5 72382 m3/h 10 m3 m
3
1800 72 40000 - - 2290.2 91608 m3/h 10 m3 m
3
2000 78 45000 - - 2827.4 113097 m3/h 10 m3 m
3
Table A- 3 60 Hz version
Qmax
DN
Order no. 7ME6520 Order no. 7ME6580
Unit Volume/
pulse
Pulse
unit
Totalizer
unit
mm Inch Fac.
settings
Min. Max. Min. Max.
15 ½ 9 0.7 28 - - US GPM 1 US G US G
25 1 22 1.9 77.8 1.9 77.8 US GPM 1 US G US G
40 1½ 52 4.9 199.1 4.9 199.1 US GPM 1 US G US G
50 2 88 6.9 277.2 7.7 311.2 US GPM 1 US G US G
65 2½ 132 11.0 440.2 13.1 525.9 US GPM 1 US G US G
80 3 220 17.6 705.1 19.9 796.7 US GPM 1 US G US MG
100 4 528 27.5 1101 31.1 1244.8 US GPM 1 US G US MG
125 5 793 44.0 1762.2 48.6 1945.1 US GPM 1 US G US MG
150 6 1101 69.3 2772.9 70 2800.9 US GPM 1 US G US MG
200 8 1761 109.7 4391.9 124.4 4979.5 US GPM 1 US G US MG
250 10 3082 176.1 7045.2 194.5 7780.5 US GPM 1 US G US MG
300 12 4402 275.1 11007.8 280 11203.9 US GPM 1 US G US MG
350 14 5283 381.2 15249.7 381.2 15249.7 US GPM 1 US G US MG
400 16 7925 497.9 19918.1 497.9 19918.1 US GPM 1 US G US MG
450 18 8806 630.2 25208.8 630.2 25208.8 US GPM 1 US G US MG
500 20 13209 778 31122 778 31122 US GPM 1 US G US MG
600 24 17611 1120.3 44815.7 1120.3 44815.7 US GPM 10 US G US MG
700 28 19812 1524.9 60999.1 1524.9 60999.1 US GPM 10 US G US MG
750 30 22014 1750.6 70024.5 1750.6 70024.5 US GPM 10 US G US MG
800 32 30820 1991.8 79672.4 1991.8 79672.4 US GPM 10 US G US MG
900 36 39626 2522.8 100835.3 2522.8 100835.3 US GPM 10 US G US MG
1000 40 52834 3112.2 124488.1 3112.2 124488.1 US GPM 10 US G US MG
1050 42 52834 3431.2 137248.1 3431.2 137248.1 US GPM 10 US G US MG
1100 44 61640 3765.7 150630.6 3765.7 150630.6 US GPM 10 US G US MG
Appendix
A.3 Coil resistance
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 55
Qmax DN
Order no. 7ME6520 Order no. 7ME6580
Unit Volume/
pulse
Pulse
unit
Totalizer
unit
1200 48 66043 4481 179262.9 4481 179262.9 US GPM 10 US G US MG
1400 54 110072 - - 6099.9 243993.7 US GPM 1000 US G US MG
1500 60 132086 - - 7002.4 280098.3 US GPM 1000 US G US MG
1600 66 154100 - - 7967.2 318689.6 US GPM 1000 US G US MG
1800 72 176115 - - 10083.5 403341.5 US GPM 1000 US G US MG
2000 78 198129 - - 12448.8 497952.5 US GPM 1000 US G US MG
A.3 Coil resistance
Table A- 4 Coil resistance
MAG 1100, MAG 1100F MAG 3100, MAG 3100P,
MAG 5100 W
(Order no. 7ME6580)
MAG 5100 W
(Order no. 7ME6520)
DN Inch Resistance Tolerance Resistance Tolerance Resistance Tolerance
2 1/12 104 Ω +/− 5 104
3 1/8 104 Ω +/− 5 104
6 1/4 99 Ω +/− 17 104
10 3/8 99 Ω +/− 17 104
151) 1/2 91 Ω +/− 9 104
25 1 91 Ω +/− 17 104 +/− 2 104 +/− 10
40 11/2 91 Ω +/− 9 92 +/− 2 92 +/− 10
50 2 91 Ω +/− 9 92 +/− 2 119.4 +/− 10
65 21/2 99 Ω +/− 17 100 +/− 2 127 +/− 10
80 3 91 Ω +/− 17 94 +/− 2 126 +/− 10
100 4 91 Ω +/− 9 92 +/− 2 125 +/− 10
125 5 92 +/− 2 126 +/− 10
150 6 94 +/− 2 116 +/− 10
200 8 90 +/− 2 109 +/− 10
250 10 92 +/− 2 104 +/− 10
300 12 100 +/− 2 108 +/− 10
350 14 112 +/− 2 100 +/− 6
400 16 100 +/− 4 100 +/− 6
450 18 108 +/− 4 100 +/− 6
500 20 122 +/− 4 100 +/− 6
600 24 115 +/− 4 98 +/− 6
700 28 128 +/− 4 98 +/− 6
750 30 133
800 32 128 +/− 4 98 +/− 6
900 36 131 +/− 4 98 +/− 6
Appendix
A.3 Coil resistance
SITRANS F M MAG 5100 W
56 Operating Instructions, 11/2010, A5E03063678-02
MAG 1100, MAG 1100F MAG 3100, MAG 3100P,
MAG 5100 W
(Order no. 7ME6580)
MAG 5100 W
(Order no. 7ME6520)
1000 40 131 +/− 4 88 +/− 6
1100 44 126
1200 48 130 +/− 4 88 +/− 6
1400 54 130
1500 60 124
1600 66 133
1800 72 133
2000 78 147
1) On MAG 1100 DN 15 produced as from May 1999 the coil resistance must be 86 ohm, +8/−4 ohm.
NOTICE
Reference values
All resistance values are at 20 °C
The resistance changes proportionally 0.4% / °C
Spare parts
Description
Cable glands, 2 pcs.
M20
½" NPT
Sealing screws for sensor/transmitter, 2 pcs.
Terminal box, in polyamide, inclusive of lid
M20
½" NPT
Appendix
A.4 Ordering
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 57
Description
Terminal box lid, in polyamide
Terminal box, in stainless steel, inclusive of lid
M20
½" NPT
Potting kit for terminal box of MAG sensors for I
P68/NEMA 6P (not for EX)
A.4 Ordering
In order to ensure that the ordering data you are using is not outdated, the latest ordering
data is always available on the Internet: Catalog process instrumentation
(http://www.siemens.com/processinstrumentation/catalogs)
Appendix
A.4 Ordering
SITRANS F M MAG 5100 W
58 Operating Instructions, 11/2010, A5E03063678-02
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 59
Glossary
ASIC
Application-Specific Integrated Circuit is an integrated circuit (IC) customized for a particular
use, rather than intended for general-purpose use.
EMC
Electromagnetic compatibility (EMC) is the branch of electrical sciences which studies the
unintentional generation, propagation and reception of electromagnetic energy with
reference to the unwanted effects (Electromagnetic Interference, or EMI) that such energy
may induce. The goal of EMC is the correct operation, in the same electromagnetic
environment, of different equipment which use electromagnetic phenomena, and the
avoidance of any interference effects.
IP
An IP (Ingress Protection) number is used to specify the environmental protection of
enclosures around electronic equipment. These ratings are determined by specific tests. The
IP number is composed of two numbers, the first referring to the protection against solid
objects and the second against liquids. The higher the number, the better the protection. For
example, in IP67 the first Number (6) means that the device is totally protected against dust,
and the second (7) that it is protected against the effect of immersion between 15cm and 1m
PED
The Pressure Equipment Directive (97/23/EC) is the legislative framework on European level
for equipment subject to a pressure hazard. It was adopted by the European Parliament and
the European Council in May 1997 and has been obligatory throughout the European Union
since May 2002.
SENSORPROM
All sensor related settings/data saved on an EPROM. SENSORPROM technology
automatically configures the transmitter at start up providing calibration data, pipe size,
sensor type, and output settings. The SENSORPROM automatically stores values or
settings changed by users, and automatically re-programs any new transmitter without loss
of accuracy.
USM
USM II is a Communication Platform. The Siemens USM II concept enables fitting of add-on
bus modules without loss of functionality:
1. All modules can be fitted as true "plug & play"
2. Module and transmitter are automatically configured through the SENSORPROM
Glossary
SITRANS F M MAG 5100 W
60 Operating Instructions, 11/2010, A5E03063678-02
SITRANS F M MAG 5100 W
Operating Instructions, 11/2010, A5E03063678-02 61
Index
A
Abrasive liquids, 18
Add-on modules, (See Communication module)
Applications, 11
C
Cable specifications, 24, 40
Cathodic protection, 21
Coil insulation check, 33
Coil resistance check, 33
Communication modules, 11
Compliance, 7
Contact person, 6
Customer Support Hotline, 30
D
Decontamination, 31
Dimensions, 47
Direct burial, 28
Document history, 5
E
Electrical connection
Cable specifications, 24
Remote installations, 24
Safety instructions, 23
Electrode resistance check, 34
Empty pipe detection, 18
F
FAQ
Fluctuating process values, 34
Flange mating dimensions, 51
G
Gas / Air bubbles, 18
H
Hazardous area
Approvals, 10
Horizontal pipes
Installation in, 18
Hotline, 30
I
Inlet / outlet conditions, 16
Installation
in U-tube, 16
Indoor/outdoor, 15
Large pipes, 17
Location in system, 16
Mounting of sensor, 19
Pipes with free outlet, 16
Remote, 24
Safety instructions, 15
Internet
Contact person, 6, 31
Flowdocumentation, 6
Support, 31
Introduction, 5
Items supplied, 5
L
Laws and directives, 7
M
Mains supply, 23
Maintenance, 29
Material compatibility, 7
Measurement principle, 12
Mounting, (See Installation)
P
Potential equalization, 21
Potting, 27
Pressure
Safety instructions, 15
Index
SITRANS F M MAG 5100 W
62 Operating Instructions, 11/2010, A5E03063678-02
Pressure Equipment Directive, 8
Process fluid
Conductivity, 42
Protective conductor terminal, 24
Protective earth, 24
R
Recalibration, 29
Repair, 30
Return procedures, 31
S
Safety
Instrument safety standards, 7
Safety instructions
Electrical connection, 23
Installation, 15
Safety notes, 7
Sensor check, 33
Sensor orientation, 18
Service, 30, 31
Support, 31
System components, 11
T
Theory of operation, 12
Torques values, 20
Transportation, 29
V
Vertical pipes
Installation in, 18
Vibrations, 19
W
Weight, 49
Wire insulation, 24
Wiring, (See Electrical connection)
Siemens Flow Instruments A/S
Nordborgvej 81
DK-6430 Nordborg
www.siemens.com/processautomation
Subject to change without prior notice
Order No.: A5E03063678
Literature No.: A5E03063678-02
Copyright Siemens AG 11.2010
All rights reserved
For more information
www.siemens.com/flow
Siemens A/S
Flow Instruments
DK-6430 Nordborg
Denmark
www.siemens.com/processautomation
*A5E03063678*
