High Voltage NP0/C0G: Class I dielectric; ultra stable electrical characteristics over time, voltage, frequency and temperature changes. Low dielectric loss. X7R: Stable Class II dielectric. SPECIFICATIONS: OPERATING TEMPERATURE RANGE: -55C to +125C TEMPERATURE COEFFICIENT: 0 30PPM/C TEMPERATURE VOLTAGE COEFFICIENT: 0 30PPM/C DISSIPATION FACTOR: 0.1% MAX. INSULATION RESISTANCE: >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (The IR at 125C is 10% of the value at 25C) WITHSTANDING VOLTAGE: See below TEST PARAMETERS: 1MHZ 50KHZ at 1.0 0.2 Vrms 100 pF, 25C 1KHZ 50HZ at 1.0 0.2 Vrms > 100 pF, 25C CAPACITANCE TOLERANCE: *F, *G, J, K *NP0/C0G only SPECIFICATIONS: OPERATING TEMPERATURE RANGE: -55C to +125C TEMPERATURE COEFFICIENT: 0 15%C MAX. TEMPERATURE VOLTAGE COEFFICIENT: X7R not applicable DISSIPATION FACTOR: 2.5% MAX. IINSULATION RESISTANCE: >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (The IR at 125C is 10% of the value at 25C) WITHSTANDING VOLTAGE: See below TEST PARAMETERS: 1KHz 50Hz at 1.0 0.2 Vrms, 25C CAPACITANCE TOLERANCE: J, K, M How To Order C1206 C0G Series Temperature See Chart Characteristic 501 -- 101 J Rated Voltage Capacitance Tolerance Code: 1st two digits (pico - Farads) *F = 1% are significant, 1st two digits *G = 2% followed by are significant J = 5% number of zeros followed by number K = 10% 201 = 200v of zeroes. M = 20% 251 = 250v 101 = 100 pF 501 = 500v R denotes decimal *NP0/C0G only *601 = 600V 6R8 = 6.8 pF *631 = 630V 102 = 1000v 202 = 2000v 302 = 3000v 402 = 4000v 502 = 5000v * 600V and 630V capacitors are available for N h Termination Marking P = Palladium Silver 6 = EIA "J" Code N = Nickel barrier, "Leave blank if Tinned Termination No Marking" Standard termination finish for this product is 100% matte Tin (Sn) any 500V capacitor ranges. Dielectric Strength is equal to 1.5 times rated voltage (WVDC) for 500 volt capacitors and 1.2 times (WVDC) for 1,000 through 5,000 volt capacitors. Circuit applications in excess of 1,000 volts may require a surface coating to prevent external arcing. All components in this section are RoHS compliant per the EU directives and definitions. 19 5900 Shepherd Mountain Cove * Austin, TX 78730 Phone: 512 / 794-0081 * Fax: 512 / 794-0087 * Toll Free: 800 / 950-8365 e-mail: sales@venkel.com * www.venkel.com E Packaging E = Embossed Tape Ceramic Chip Capacitors L W END BAND VOLTAGE AND CAPACITANCE RANGE T CAPACITOR CASE SIZE 0805 SIZE * L * W T(Max) Max E/B RATED WVDC in. mm .080 .050 .065 .020 2.03 1.27 1.65 .508 1206 SIZE * L * W T(Max) Max E/B .125 .062 .080 .020 3.18 1.58 2.03 .508 250V 500V 821 1,000V 471 .125 .095 .085 .020 3.18 2.41 2.16 .508 4.57 2.03 2.41 .508 1812 332 104 473 681 562 151 102 472 500V 1,000V 563 102 2,000V 153 221 152 562 500V 4.49 3.18 3.00 .508 1,000V 683 152 2,000V 221 183 332 121 102 470 102 471 682 500V 1825 124 222 473 471 2,000V 103 221 222 101 681 500V .180 .250 .128 .020 4.57 6.35 3.25 .508 103 1,000V 102 3,000V 471 4,000V 2225 682 472 271 101 104 821 391 500V .225 .250 .145 .020 5.72 6.35 3.68 .508 333 1,000V 822 2,000V 122 3,000V 102 4,000V 5,000V 224 562 2,000V 5,000V 224 472 1,000V 4,000V 124 332 250V .177 .125 .118 .020 474 222 3,000V SIZE * L * W T(Max) Max E/B 272 102 1,000V 4,000V SIZE * L * W T(Max) Max E/B 273 250V .180 .080 .095 .020 .1 F 123 500V 2,000V .01 F 102 3,000V SIZE * L * W T(Max) Max E/B 1000 pF 250V 1808 SIZE * L * W T(Max) Max E/B 100 pF 250V 1210 SIZE * L * W T(Max) Max E/B 10 pF 471 181 394 104 273 392 152 681 * Tolerance: 0.010" NOTE: (1) Standard ranges begin at 10pF. Please consult your sales representative if values below 10pF are required. (2) Thickness may exceed the T(Max) specification if capacitance and rated voltage are near the end of the range. Please advise your sales representative if thickness is a concern. 5900 Shepherd Mountain Cove * Austin, TX 78730 Phone: 512 / 794-0081 * Fax: 512 / 794-0087 * Toll Free: 800 / 950-8365 e-mail: sales@venkel.com * www.venkel.com NPO or X7R X7R only X7R non-RoHS compliant 20