19
5900 Shepherd Mountain Cove • Austin, TX 78730
Phone: 512 / 794-0081 • Fax: 512 / 794-0087 • Toll Free: 800 / 950-8365
e-mail: sales@venkel.com • www.venkel.com
High Voltage
Dielectric Strength is equal to 1.5 times rated voltage (WVDC) for 500 volt capacitors
and 1.2 times (WVDC) for 1,000 through 5,000 volt capacitors. Circuit applications
in excess of 1,000 volts may require a surface coating to prevent external arcing.
How To Order
C1206 C0G 501 — 101 J N h E
Series Temperature Rated Voltage Capacitance Tolerance Code: Termination Marking Packaging
See Chart Characteristic 1st two digits (pico - Farads) *F = ± 1% P = Palladium Silver 6 = EIA “J” Code E = Embossed Tape
are significant, 1st two digits *G = ± 2% N = Nickel barrier, “Leave blank if
followed by are significant J = ± 5% Tinned Termination No Marking”
number of zeros followed by number K = ± 10% Standard termination finish for this product
201 = 200V of zeroes. M = ± 20% is 100% matte Tin (Sn)
251 = 250V 101 = 100 pF
501 = 500V R denotes decimal *NP0/C0G only
*601 = 600V 6R8 = 6.8 pF
*631 = 630V
102 = 1000V
202 = 2000V
302 = 3000V
402 = 4000V
502 = 5000V
SPECIFICATIONS:
OPERATING TEMPERATURE RANGE: -55°C to +125°C
TEMPERATURE COEFFICIENT: 0 ± 30PPM/°C
TEMPERATURE VOLTAGE COEFFICIENT: 0 ± 30PPM/°C
DISSIPATION FACTOR: 0.1% MAX.
INSULATION RESISTANCE: >1000 ohms F or 100 G ohms,
whichever is less at 25°C, VDCW.
(The IR at 125°C is 10% of the value at 25°C)
WITHSTANDING VOLTAGE: See below
TEST PARAMETERS: 1MHZ ± 50KHZ at 1.0 ± 0.2 Vrms ≤ 100 pF, 25°C
1KHZ ± 50HZ at 1.0 ± 0.2 Vrms > 100 pF, 25°C
CAPACITANCE TOLERANCE: *F, *G, J, K *NP0/C0G only
NP0/C0G:
Class I dielectric;
ultra stable electrical
characteristics over time,
voltage, frequency and
temperature changes.
Low dielectric loss.
SPECIFICATIONS:
OPERATING TEMPERATURE RANGE: -55°C to +125°C
TEMPERATURE COEFFICIENT: 0 ± 15%∆°C MAX.
TEMPERATURE VOLTAGE COEFFICIENT: X7R not applicable
DISSIPATION FACTOR: 2.5% MAX.
IINSULATION RESISTANCE: >1000 ohms F or 100 G ohms,
whichever is less at 25°C, VDCW.
(The IR at 125°C is 10% of the value at 25°C)
WITHSTANDING VOLTAGE: See below
TEST PARAMETERS: 1KHz ± 50Hz at 1.0 ± 0.2 Vrms, 25°C
CAPACITANCE TOLERANCE: J, K, M
X7R:
Stable Class II dielectric.
All components in this section are RoHS compliant per the EU directives and definitions.
* 600V and 630V capacitors are available for any 500V capacitor ranges.
Ceramic Chip Capacitors
5900 Shepherd Mountain Cove • Austin, TX 78730
Phone: 512 / 794-0081 • Fax: 512 / 794-0087 • Toll Free: 800 / 950-8365
e-mail: sales@venkel.com • www.venkel.com
20
NOTE: (1) Standard ranges begin at 10pF. Please consult your sales representative if values below 10pF
are required.
(2) Thickness may exceed the T(Max) specification if capacitance and rated voltage are near the
end of the range. Please advise your sales representative if thickness is a concern.
102
T
L
WEND
BAND
250V
500V
1,000V
2,000V
3,000V
4,000V
273102
123
272
250V
500V
1,000V
2,000V
102 153
250V
500V
1,000V
2,000V
3,000V
4,000V
332 683
562 124
152 183
221 332
121 102
470 471
500V
1,000V
2,000V
3,000V
4,000V
5,000V
682
472 124
224
222 473
471 103
221 222
101 681
103 224
562 104
102 682
471 472
271 821
101 391
500V
1,000V
2,000V
3,000V
4,000V
5,000V
333 394
822 104
122 273
102 392
471 152
181 681
1210
SIZE
*L
.125 3.18
*W
.095 2.41
T(Max)
.085 2.16
Max E/B
.020 .508
1808
SIZE
*L
.180 4.57
*W
.080 2.03
T(Max)
.095 2.41
Max E/B
.020 .508
1812
SIZE
*L
.177 4.49
*W
.125 3.18
T(Max)
.118 3.00
Max E/B
.020 .508
1825
SIZE
*L
.180 4.57
*W
.250 6.35
T(Max)
.128 3.25
Max E/B
.020 .508
VOLTAGE AND CAPACITANCE RANGE
250V
500V
1,000V
2,000V
332 104
102 473
681 562
472 474
222 563
151 102
221 152
1206
SIZE
*L
.125 3.18
*W
.062 1.58
T(Max)
.080 2.03
Max E/B
.020 .508
250V
500V
1,000V
0805
SIZE
*L
.080 2.03
*W
.050 1.27
T(Max)
.065 1.65
Max E/B
.020 .508
2225
SIZE
*L
.225 5.72
*W
.250 6.35
T(Max)
.145 3.68
Max E/B
.020 .508
CAPACITOR
CASE SIZE
RATED
WVDC
in. mm
10 pF 100 pF 1000 pF .01 µF .1 µF
821
471
*
Tolerance: ± 0.010"
NPO or X7R
X7R only
X7R non-RoHS compliant
