U8201A - KEYSIGHT TECHNOLOGIES

Agilent U3606A

Multimeter|DC Power Supply

Data Sheet

The real two instruments in one box

Features

•Two independent instruments

in one box

•Nine basic measurements

as well as 4-wire milliohm

measurement and eight math

functions

•Measurement speed: up to

37 readings/s

•Low error rate: up to 0.025%

DCV accuracy

•30-W dual-range power supply

with remote sensing

•Excellent load regulation: up to

0.01%+3 mV

•OVP and OCP load protection

•Auto scan and ramp, and

built-in 4.8 kHz square-wave

generator

•USB-TMC488.2 and GPIB

connectivity

•Kensington lock slot security

Pick both

Digital multimeter (DMM) and power

supply? Simultaneous and inde-

pendent? Small and cost-effective?

Get all this and more in the Agilent

U3606A multimeter|DC power supply.

This convenient new hybrid combines

a 5½-digit DMM and 30-W dual-range

supply in a single unit. Operating

simultaneously and independently,

the instruments provide efficient,

affordable testing while saving space

on the bench or in a rack.

The 5.5-digit DMM

The 5.5-digit DMM includes nine

essential multimeter capabilities as

well as 4-wire milliohm measurement

and eight built-in math functions. The

DMM also provides a fast measure-

ment speed of up to 37 readings/s,

and a low error rate of up to 0.025%

DCV accuracy.

Physical security and seamless

system integration

Instruments may be at risk of theft or

misplacement when left unattended

on the bench. With the hybrid multi-

meter’s rear Kensington lock slot, you

can secure your instrument and be

assured that it is where you expect it

to be for your continued testing the

next day. The rackmountable U3606A

also enables seamless integration

into your system via popular GPIB

and USB-TMC488.2 interfaces,

programmable with standard SCPI

commands.

Get to know the U3606A’s

replacement - the U3606B

www.agilent.com/find/dmm-power

The 30-W DC power supply

The 30-W DC power supply provides

a dual-range output of 30 V/1 A

and 8V/3 A, with an excellent load

regulation of up to 0.01%+3 mV. The

power supply adds overvoltage and

overcurrent load protection (OVP and

OCP), a built-in square-wave genera-

tor, and auto scan and ramp for multi-

level DC bias testing. Remote sensing

capability further ensures accurate

supply of power at load end.

Square-wave generator

Square-wave output is a unique

function for many applications, such

as pulse-width modulation (PWM)

output, adjustable voltage control,

and synchronous clock (baud rate

generator). You can also use this

function to check and calibrate flow-

meter displays, counters, tachom-

eters, oscilloscopes, frequency

converters, frequency transmitters,

and other frequency input devices.

The U3606A’s square-wave output

provides selectable frequencies up to

4.8 kHz with variable duty cycles and

amplitudes.

Sweep functions

Sweep functions in the U3606A are

auto ramp and scan outputs for low-

speed multilevel DC bias tests, such

as margin tests, power cycling tests

and relay control. Both functions are

conveniently configurable from the

front panel to sweep up to 100 steps

for scan and 10,000 steps for ramp,

programmable to 105% of full scale.



Auto scan output

Auto ramp output

Amplitude (V/A)

Amplitude

end position

Amplitude

end position

Scan dwelling time

Total dwelling time

Time (t)

Number

of steps

Number of steps

Take a closer look

VFD display

Source

terminals

Local/Shift key

Source operation keys

Power

On/Off

button

Multimeter

operation keys

Kensington

lock slot

GPIB (IEEE-488)

connector

USB 2.0 Type B

connector

Rear output terminals

for remote sense

Autorange

and manual

range keys

Multimeter

terminals

Figure 1. Front panel of the U3606A.

Figure 2. Rear panel of the U3606A.

Ventilation fan

Chassis

ground lug

AC power

connector

AC line fuse

Digital multimeter specifications

Specification assumptions:

•Specifications stated are after 60-minutes of warm-up and for 5½-digit resolution

•One-year calibration cycle, with calibration temperature of 18 °C to 20 °C

•Operating temperature: 18 °C to 28 °C (64.4 °F to 82.4 °F)

•Accuracy is expressed as ±(% of reading + % of range)

•Temperature coefficient: Add [0.1 x (the specified accuracy) / °C] for 0 °C to 18 °C and 28 °C to 55 °C

•Relative humidity (RH) up to 80% at 30 °C, proportional to 50% for 30 °C to 55 °C

DC specifications

Function Range1

Test current

or burden

voltage

Accuracy ±(% of reading + % of range)

Temperature

coefficient

0 ºC to 18 ºC

28 ºC to 55 ºC

24 hours2

23 ºC ± 1 ºC

90 days

23 ºC ± 5 ºC

1 year

23 ºC ± 5 ºC

DC voltage 100.000 mV

1.00000 V

10.0000 V

100.000 V

1000.00 V

–

0.012 + 0.008

0.012 + 0.005

0.015 + 0.008

0.015 + 0.005

0.025 + 0.008

0.025 + 0.005

0.0015 + 0.0005

0.0010 + 0.0005

0.0020 + 0.0005

0.0015 + 0.0005

DC current310.0000 mA

100.000 mA

1.00000 A

3.0000 A

< 0.2 V

< 0.3 V

< 0.7 V

0.05 + 0.015

0.05 + 0.005

0.05 + 0.007

0.05 + 0.015

0.05 + 0.005

0.05 + 0.007

0.05 + 0.015

0.05 + 0.005

0.15 + 0.007

0.0060 + 0.0005

0.0100 + 0.0005

0.0150 + 0.0010

Resistance4100.000 

1000.00 

10.0000 k

100.000 k

1.00000 M

10.0000 M

100.000 M

0.83 mA

100 A

10 A

900 nA

205 nA

205 nA || 10 M

0.04 + 0.008

0.04 + 0.005

0.05 + 0.005

0.20 + 0.005

1.60 + 0.005

0.04 + 0.008

0.04 + 0.005

0.05 + 0.005

0.20 + 0.005

1.60 + 0.005

0.05 + 0.008

0.05 + 0.005

0.06 + 0.005

0.25 + 0.005

2.00 + 0.005

0.0050 + 0.0005

0.0150 + 0.0005

0.1500 + 0.0005

Continuity 1.0000 k 0.83 mA 0.04 + 0.005 0.04 + 0.005 0.05 + 0.005 0.0050 + 0.0005

Diode51.0000 V 0.83 mA 0.04 + 0.005 0.04 + 0.005 0.05 + 0.005 0.0050 + 0.0005

Capacitance61.000 nF

10.00 nF

100.00 nF

1.000 F

10.00 F

100.0 F

1000 F

10000 F

0.75 A

8.3 A

83 A

0.83 mA

–

2.0 + 0.8

1.0 + 0.5

2.0 + 0.5

0.02 + 0.001

1. 20% over-range on all ranges, except for 1000 Vdc range.

2. Relative to calibration standards.

3. Any current measurement greater than 500 mA will have a temporary thermo-effect. If you wish to measure a lower current or offset current im-

mediately after a high-current measurement, ensure that the U3606A has cooled down.

4. Specifications stated are for 2-wire resistance measurements using Null math operation. Without Null, add a 0.2 Ω error. To eliminate noise interfer-

ence which may be induced by the test leads, a shielded test cable is recommended for resistances above 100 kΩ.

5. Specifications stated are for the voltage measured at the input terminals only. The test current (1 mA) is typical. Variation in the current source will

create some variation in the voltage dropped across a diode junction.

6. Specifications stated are for open test lead measurements with film capacitor or better, using Null math operation.

Digital multimeter specifications (continued)

Low-resistance specifications

Range Test current

Accuracy ±(% of reading + % of range)1

1 year (23 ºC ± 5 ºC)

100 m 1.0000 A 0.25 + 0.05

1000 m 0.1000 A 0.25 + 0.03

10  0.1000 A 0.25 + 0.03

1. Four-wire measurement method is used. Test current is sent from the FORCE terminals and resistance is measured at the SENSE terminals.

AC specifications

Function Range1

Frequency

range

Accuracy ±(% of reading + % of range)

Temperature

coefficient

0 ºC to 18 ºC

28 ºC to 55 ºC

24 hours2

23 ºC ± 1 ºC

90 days

23 ºC ± 5 ºC

1 year

23 ºC ± 5 ºC

True rms AC

voltage3

100.000 mV

to 750.00 V4

20 Hz to 45 Hz

45 Hz to 10 kHz

10 kHz to 30 kHz

30 kHz to 100 kHz7

0.60 + 0.1

0.16 + 0.1

0.80 + 0.1

3.00 + 0.2

0.60 + 0.1

0.16 + 0.1

0.80 + 0.1

3.00 + 0.2

1.00 + 0.15

0.20 + 0.1

1.00 + 0.16

3.00 + 0.28, 9

0.02 + 0.02

0.05 + 0.02

True rms AC

current

10.0000 mA

to 3.0000 A10

20 Hz to 45 Hz

45 Hz to 1 kHz

1 kHz to 10 kHz11

0.80 + 0.1

0.40 + 0.1

2.00 + 0.2

0.80 + 0.1

0.40 + 0.1

2.00 + 0.2

1.50 + 0.1

0.50 + 0.1

2.00 + 0.2

0.02 + 0.02

1. 20% over-range on all ranges, except for 750 Vac range.

2. Relative to calibration standards.

3. Specifications stated are for input signals greater than 5% of range.

4. Available ranges: 100.000 mV, 1.00000 V, 10.0000 V, 100.000 V, 750.00 V.

5. For 750 V range accuracy is specified for input less than 200 Vrms.

6. For 100 mV range, the 10 kHz to 30 kHz accuracy is 1.5 + 0.3.

7. Additional error 0.003% of full scale per kHz to be added when signal input changes less than 10% of range.

8. For 100 mV range, the 30 kHz to 100 kHz accuracy is 5 + 0.3.

9. For 750 V range accuracy is specified for input less than 300 Vrms.

10. Available ranges: 10.0000 mA, 100.000 mA, 1.00000 A, 3.0000 A.

11. For 1 A and 3 A ranges, the accuracy is specified for frequencies less than 5 kHz.

Digital multimeter specifications (continued)

Frequency specifications

Function Input range

Frequency range:

minimum input

frequency = 1 Hz

Accuracy

±(% of reading + % of range)

Temperature

coefficient

0 ºC to 18 ºC

28 ºC to 55 ºC1 year (23 ºC ± 5 ºC)

Frequency Voltage:

100 mV to 750 V1

< 2 Hz

< 20 Hz

20 Hz to 100 kHz

100 kHz to 300 kHz

0.18 + 0.003

0.04 + 0.003

0.02 + 0.003

0.005

Current:

10 mA to 3 A

< 2 Hz

< 20 Hz

20 Hz to 10 kHz

0.18 + 0.003

0.04 + 0.003

0.02 + 0.003

0.005

Input range2

Minimum frequency sensitivity for voltage measurement (RMS sine wave)

20 Hz to 100 kHz 100 kHz to 300 kHz 300 kHz to 1 MHz

100 mV

1.0 V

10 V

100 V

750 V

50 mV

100 mV

1 V

10 V

100 V

50 mV

120 mV

1.2 V

12 V

–

0.5 V

–

Input range

Minimum frequency sensitivity for current measurement (RMS sine wave)

20 Hz to 100 kHz

10 mA

100 mA

1 A

3 A

1 mA

10 mA

100 mA

300 mA

1. For 100 mV and 1 V ranges, the measurable frequency is up to 1 MHz at 0.5 V input signal.

2. Maximum input for the specified accuracy = 10 x range or 1000 Vdc.

All frequency counters are susceptible to errors when measuring low-voltage, low-frequency signals. Shielding inputs from

external noise pickup is critical for minimizing measurement errors.

Duty cycle and pulse width specifications

Function Range Resolution Accuracy at full scale

Duty cycle 100.000%10.001% 0.3% + 0.2% per kHz

Pulse width 199.999 ms2

1999.99 ms2

0.001 ms

0.01 ms

Duty cycle/frequency

1. The range is from {10 µs × frequency × 100%} ~ {[1 – (10 µs × frequency)] × 100%}. For example, a 1 kHz signal can be measured from

1% ~ 99%.

2. The positive or negative pulse width must be greater than 10 µs. The range of the pulse width is determined by the frequency of the signal.

Digital multimeter specifications (continued)

Measurement speeds (typical)

Function Rate

Reading speed1

(readings/second)

Reading speed

over USB2

(readings/second)

Reading speed

over GPIB3

(readings/second)

DC voltage

(10 V)

Slow (5½ digits)

Fast (4½ digits)

DC current

(1 A)

Slow (5½ digits)

Fast (4½ digits)

AC voltage

(10 V at 1 kHz)

Slow (5½ digits)

Fast (4½ digits)

AC current

(1 A at 1 kHz)

Slow (5½ digits)

Fast (4½ digits)

Resistance

(100 k)

Slow (5½ digits)

Fast (4½ digits)

Capacitance

(10 F)

Slow/Fast (3½ digits) 5 4.4 4.6

Frequency

(voltage path at

10 V, 1 kHz)

Slow (5½ digits)

Fast (4½ digits)

2.7

Frequency

(current path at

10 V, 1 kHz)

Slow (5½ digit)

Fast (4½ digit)

2.7

1. Reading rate of the A/D converter.

2. Number of measurements per second that can be read through USB using SCPI “READ?” command.

3. Number of measurements per second that can be read through GPIB using SCPI “READ?” command.

Supplementary specifications

DC voltage

Measurement method Sigma Delta A-to-D converter

Maximum input voltage 1000 Vdc on all ranges

Input impedance 10 M ± 2% range (typical) in parallel with capacitance < 120 pF

Input protection 1000 Vrms on all ranges, < 0.3 A short circuit

Response time Approximately 0.15 s when the displayed reading reaches 99.9% DC value of the tested

input signal at the same range

DC current

Measurement method Sigma Delta A-to-D converter

Maximum input current 10 mA to 3.0 A DC

Burden voltage and shunt resistance •< 0.2 V, 10  for 10 mA range

•< 0.2 V, 1  for 100 mA range

•< 0.3 V, 0.1  for 1 A range

•< 0.7 V, 0.01  for 3 A range

Input protection Protected with 3.15 A/500 V, FF fuse

Response time Approximately 0.15 s when the displayed reading reaches 99.9% DC value of the tested

input signal at the same range

Digital multimeter specifications (continued)

Supplementary specifications

AC voltage

Measurement method AC coupled true rms

Maximum input voltage 750 Vrms/1200 Vpeak/3 x 107 V-Hz of product

Input impedance 1 M ± 2% range (typical) in parallel with capacitance < 120 pF

Input protection 750 Vrms on all ranges

Crest factor For < 5:1 errors included. Limited by the peak input and 100 kHz bandwidth. Maximum 3.0 at

full scale.

Peak input 300% of range. Limited by maximum input.

Response time Approximately 2.5 s when the displayed reading reaches 99.9% AC rms value of the tested

input signal at the same range.

Overload ranging Will select higher range if peak input overload is detected during auto range. Overload is

reported in manual ranging.

AC current

Measurement method AC coupled true rms

Maximum input current 10 mA to 3.0 A DC or AC rms

Burden voltage and shunt resistance •< 0.2 V, 10  for 10 mA range

•< 0.2 V, 1  for 100 mA range

•< 0.3 V, 0.1  for 1 A range

•< 0.7 V, 0.01  for 3 A range

Input protection Protected with 3.15 A/500 V, FF fuse

Crest factor For < 5:1 errors included. Limited by the peak input and 100 kHz bandwidth. Maximum 3.0 at

full scale.

Peak input 300% of range. Limited by maximum input.

Response time Approximately 2.5 s when the displayed reading reaches 99.9% AC rms value of the tested

input signal at the same range.

Resistance

Measurement method Two-wire, open-circuit voltage limited to < 5 V

Open circuit voltage < +5.0 Vdc

Input protection 1000 Vrms on all ranges, < 0.3 A short circuit

Response time Approximately 0.15 seconds for 1 M and ranges below 1 M

Low-resistance

Measurement method Four-wire; test current is sent from the FORCE terminals and resistance measured at the

SENSE terminals.

Input protection •FORCE terminals: 3.15 A/250 V

•SENSE terminals: 1000 Vrms on all ranges, < 0.3 A short circuit

Continuity

Measurement method 0.83 mA ± 0.2% constant current source

Open circuit voltage < +5.0 Vdc

Audible tone Continuous beeping when reading is less than the threshold resistance of 10  at 1.0 k

range

Input protection 1000 Vrms on all ranges, < 0.3 A short circuit

Digital multimeter specifications (continued)

Supplementary specifications

Diode

Measurement method 0.83 mA ± 0.2% constant current source

Open circuit voltage < +5.0 Vdc

Audible tone •Continuous beeping when level is below +50 mV DC

•Single tone for normal forward-biased diode or semiconductor junction where

0.3 V ≤ reading ≤ 0.8 V

Input protection 1000 Vrms on all ranges, < 0.3 A short circuit

Capacitance

Measurement method Computed from constant current source charge time, typical 0.2 V to 1.4 Vac signal level

Maximum voltage at full scale •For 1 nF to 10 F range: < 1.5 V

•For 100 F to 10000 F: 0.33 V

Input protection 1000 Vrms on all ranges, < 0.3 A short circuit

Response time Approximately 1 s for 100 F and ranges below 100 F

Charge and discharge voltage 5 Vpp (approximately from +3 V to –2 V)

Frequency

Measurement method Reciprocal counting technique

Signal level 0.2 V to 1.4 V

Input protection •Voltage path: 1000 Vrms on all ranges, < 0.3 A short circuit

•Current path: Protected with 3.15 A/500 V, FF fuse

Maximum display counts (excluding frequency)

5½ digits 120,000

4½ digits 12,000

Noise rejection

Common mode rejection ratio (CMRR)

for 1 k unbalanced in LO lead

•DC: 140 dB

•AC: 70 dB

Normal mode rejection ratio (NMRR) •60 Hz ± 0.1%:

5½ digits: 65 dB, 4½ digits: 0 dB

•50 Hz ± 0.1%:

5½ digits: 55 dB, 4½ digits: 0 dB

Power supply specifications

Specification assumptions:

•Specifications stated are after 60-minutes of warm-up with no load

•Operating temperature: 18 °C to 28 °C (64.4 °F to 82.4 °F)

•Accuracy is expressed as ±(% of output + offset) at 23 °C ± 5 °C

•Temperature coefficient: Add [0.1 x (the specified accuracy) / °C] for 0 °C to 18 °C and 28 °C to 55 °C

•Relative humidity (RH) up to 80% at 30 °C, proportional to 50% for 30 °C to 55 °C

DC power supply specifications

Output ratings •Range S1: 0 V to 30 V, 0 A to 1 A

•Range S2: 0 V to 8 V, 0 A to 3 A

Programming accuracy

1 year (@ 23 ºC ± 5 ºC), ±(% of output + offset)

•0.05% + 5 mV

•0.15% + 3 mA

Readback accuracy

1 year over GPIB and USB or front panel with respect to

actual output (@ 23 ºC ± 5 ºC), ±(% of output + offset)

•0.05% + 5 mV

•0.15% + 3 mA

Ripple and noise

With outputs ungrounded, or with either output

terminal grounded, 20 Hz to 1 MHz3

•< 2 mVrms; < 30 mVpp

•< 1 mArms

Front terminal load regulation

±(% of output + offset)

•< 3 mV1

•< 0.03% + 0.3 mA

Rear terminal load regulation

±(% of output + offset)

•< 0.01% + 3 mV

•< 0.03% + 0.3 mA

Line regulation Voltage: 3 mV

Current: 1.5 mA

Programming resolution 1 mV, 0.1 mA

Readback resolution 1 mV, 0.1 mA

Front panel resolution 1 mV, 0.1 mA

Transient response time Less than 450 ms for output to recover to within 50 mV following a

change in output current from full load to half load or vice versa

Command processing time Average time for output voltage to begin to change after receipt of

digital data when instrument is connected directly to the USB or GPIB

is less than 100 ms

Overvoltage protection (for CC mode) •Accuracy: 0.5% + 0.5 V

•Activation time2: < 2ms

Overcurrent protection (for CV mode) •Accuracy: 0.5% + 0.05 A

•Activation time2: < 2 ms

1. Contacts and leads resistance may contribute an additional error of 6 mV/A (typical).

2. Average time for the detection of OVP or OCP condition.

3. Refer to U3606A User’s and Service Guide (U3606-90013); CV noise effect measurement on page 166.

Power supply specifications (continued)

Sweep specifications

Function Range Amplitude1Step Dwelling time

Scan Constant voltage S1 (30 V/1 A)

S2 (8 V/3 A)

0 to 31.500 V

0 to 8.4000 V

1 step to 100 steps 1 s to 99 s

Constant current S1 (30 V/1 A)

S2 (8 V/3 A)

0 to 1.0500 A

0 to 3.1500 A

1 step to 100 steps 1 s to 99 s

Ramp Constant voltage S1 (30 V/1 A)

S2 (8 V/3 A)

0 to 31.500 V

0 to 8.4000 V

1 step to 10,000 steps 300 ms/step (typical)

Constant current S1 (30 V/1 A)

S2 (8 V/3 A)

0 to 1.0500 A

0 to 3.1500 A

1 step to 10,000 steps 300 ms/step (typical)

1. Amplitude start position is fixed at 0 (V or A) by default.

Square-wave output specifications

Parameter Range Resolution Accuracy

Frequency 0.5, 2, 5, 6, 10, 15, 25, 30, 40, 50, 60, 75, 80, 100, 120, 150,

200, 240, 300, 400, 480, 600, 800, 1200, 1600, 2400, 4800 Hz

0.01 Hz 0.005% + 1 count

Duty cycle 0.39% to 99.60% 0.39%10.4%1, 2

Pulse width 1/frequency Range/256 Duty cycle/frequency1, 3

Amplitude S1 (30 V/1 A)

S2 (8 V/3 A)

1 mV

0.2 V

1. Specification applies when the positive or negative pulse width is greater than 50 µs.

2. For frequency signals greater than 100 Hz, an additional 0.1% per 100 Hz is to be added.

Accuracy = 0.4% + ( frequency – 1 ) × 0.1%

100

3. The accuracy of pulse width could also be calculated as [0.4% + (frequency/100 – 1) × 0.1%]/frequency.

Rise/fall time is less than 25 s. Specifications are based on a resistive load.

Supplementary specifications

Output programming range

Range Output programming OV/OC OVP/OCP

S1 0 V to 31.500 V/0 A to 1.05 A 31.500 V/1.05 A 33.000 V/1.1 A

S2 0 V to 8.4 V/0 A to 3.15 A 8.4 V/3.15 A 8.8 V/3.3 A

Remote sensing capability

Range S1 (30 V/1 A) Up to a 0.75-volt drop per load lead

Range S2 (8 V/3 A) Up to a 0.5-volt drop per load lead

Temperature coefficient: ± (% of output + offset)/ °C for 0 °C to 18 °C and 28 °C to 55 °C

Voltage 0.005% + 0.5 mV/°C

Current 0.02% + 1 mA/°C

Voltage programming speed (excludes command processing time)

Up 300 ms (full load and no load)

Down 400 ms (full load and no load)

General characteristics

Power supply •Universal 100 Vac to 240 Vac ±10%

•AC line frequency 45 Hz to 66 Hz (360 Hz to 440 Hz for 100/120 V operation)

Power consumption 150 VA maximum

Current Input Fuse 3.15 A, 500 V FF fuse (on front panel)

Display Highly visible vacuum-fluorescent display (VFD)

Operating environment •Operating temperature from 0 °C to +55 °C

•Relative humidity up to 80% at 30 °C RH (non-condensing)

•Altitude up to 2000 meters

•Pollution degree 2

•For indoor use only

Storage compliance –40 °C to 70 °C

Safety compliance Certified with:

•IEC 61010-1:2001/EN61010-1:2001 (2nd Edition)

•Canada: CAN/CSA-C22.2 No. 61010-1-04

•USA: ANSI/UL 61010-1:2004

EMC compliance Certified with:

•IEC61326-1:2005 / EN61326-1:2006

•CISPR 11:2003 / EN55011:2007 (Group 1 Class A)

•Canada: ICES/NMB-001:2004

•Australia/New Zealand: AS/NZS CISPR11:2004

Shock and vibration Tested to IEC/EN 60068-2

Remote interface •GPIB IEEE-488

•Full Speed USB 2.0 (Type B)

•USBTMC 488.2 Class device

•USB-CDC

Programming language Standard Commands for Programmable Instruments (SCPI)

Measurement category •CAT II, 300 V

•CAT I, 1000 Vdc, 750 Vac rms

•2500 Vpk transient over voltages

Dimensions (H × W × D) 105 × 255 × 329 mm (with rubber bumpers)

87 x 215 x 312 mm (without rubber bumpers)

Weight 3.775 kg (with rubber bumpers)

3.535 kg (without rubber bumpers)

Warranty Three years

Calibration cycle One year

Warm-up time 60 minutes

Ordering information

Standard shipped items

•Quick Start Guide

•Product Reference CD

•Agilent IO Library Suite

•Certificate of Calibration

•U8201A Combo Test Lead Kit

•USB 2.0 High-Speed Type-A to

Type-B cable

•AC power cord

Warranty options

•R-51B-001-3C Extended warranty

from one year to three years

•R-51B-001-5C Extended warranty

from one year to five years

U8201A Combo Test Lead Kit U3606A-1CM Rack Mount Kit U8202A Electronic Test Lead Kit

(for DMM function)

34133A Precision Electronic Test Leads

(for DMM function)

34330A Current Shunt (30 A)

(for DMM function)

34136A 40 kV high-voltage probe

(for DMM function)

11059A Kelvin Probe Set and

11062A Kelvin Clip Set (for DMM function)

E3600A-100 Test Lead Kit

(for DC power supply function)

I/O connectivity options

For control via GPIB interface

•82350B/82351A PCI/PCIe

high-performance GPIB

interface card

•82357B USB/GPIB converter

•E5810A LAN/GPIB gateway

•10833D/A/B/C/F/G GPIB cables

•10834A GPIB-to-GPIB adapter

For control via USB interface

•E5813A networked 5-port USB hub

Optional accessories

myAgilent

www.agilent.com/find/myagilent

A personalized view into the information most relevant to you.

www.axiestandard.org

AdvancedTCA® Extensions for Instrumentation and Test (AXIe)

is an open standard that extends the AdvancedTCA for general

purpose and semiconductor test. Agilent is a founding member of

the AXIe consortium.

www.lxistandard.org

LAN eXtensions for Instruments puts the power of Ethernet and the

Web inside your test systems. Agilent is a founding member of the

LXI consortium.

www.pxisa.org

PCI eXtensions for Instrumentation (PXI) modular instrumentation

delivers a rugged, PC-based high-performance measurement and

automation system.

Three-Year Warranty

www.agilent.com/find/ThreeYearWarranty

Beyond product specification, changing the ownership experience.

Agilent is the only test and measurement company that offers

three-year warranty on all instruments, worldwide.

Agilent Assurance Plans

www.agilent.com/find/AssurancePlans

Five years of protection and no budgetary surprises to ensure your

instruments are operating to specifications and you can continually

rely on accurate measurements.

www.agilent.com/quality

Agilent Electronic Measurement Group

DEKRA Certified ISO 9001:2008

Quality Management System

Agilent Channel Partners

www.agilent.com/find/channelpartners

Get the best of both worlds: Agilent’s measurement expertise and

product breadth, combined with channel partner convenience.

www.agilent.com

www.agilent.com/ﬁnd/U3606A

For more information on Agilent

Technologies’ products, applications or

services, please contact your local Agilent

office. The complete list is available at:

www.agilent.com/find/contactus

Americas

Canada (877) 894 4414

Brazil (11) 4197 3600

Mexico 01800 5064 800

United States (800) 829 4444

Asia Paciﬁc

Australia 1 800 629 485

China 800 810 0189

Hong Kong 800 938 693

India 1 800 112 929

Japan 0120 (421) 345

Korea 080 769 0800

Malaysia 1 800 888 848

Singapore 1 800 375 8100

Taiwan 0800 047 866

Other AP Countries (65) 375 8100

Europe & Middle East

Belgium 32 (0) 2 404 93 40

Denmark 45 45 80 12 15

Finland 358 (0) 10 855 2100

France 0825 010 700*

*0.125 €/minute

Germany 49 (0) 7031 464 6333

Ireland 1890 924 204

Israel 972-3-9288-504/544

Italy 39 02 92 60 8484

Netherlands 31 (0) 20 547 2111

Spain 34 (91) 631 3300

Sweden 0200-88 22 55

United Kingdom 44 (0) 118 927 6201

For other unlisted countries:

www.agilent.com/find/contactus

(BP-09-27-13)

Product specifications and descriptions in

this document subject to change without

notice.

Published in USA, January 10, 2014

5990-3971EN