TSOP341..YA1 Vishay Semiconductors IR Receiver Modules for Remote Control Systems Description The TSOP341..YA1 - series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the operation with short burst transmission codes and high data rates at a supply voltage of 3 V. 1 2 16668 3 Features Mechanical Data * Photo detector and preamplifier in one package * Internal filter for PCM frequency e3 * Improved shielding against electrical field disturbance * TTL and CMOS compatibility * Output active low * Supply voltage range: 2.7 V to 5.5 V * High immunity against ambient light * Lead (Pb)-free component * Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC Pinning: 1 = OUT, 2 = GND, 3 = VS Parts Table Part Carrier Frequency TSOP34130YA1 30 kHz TSOP34133YA1 33 kHz TSOP34136YA1 36 kHz TSOP34137YA1 36.7 kHz TSOP34138YA1 38 kHz TSOP34140YA1 40 kHz TSOP34156YA1 56 kHz Special Features * Enhanced data rate up to 4000 bit/s * Operation with short short bursts possible ( 6 cycles/burst) Block Diagram Application Circuit 17170 3 30 k VS 1 Input AGC Band Pass Demodulator OUT 2 PIN Document Number 82256 Rev. 1.1, 19-Apr-06 Control Circuit GND Transmitter TSOPxxxx with TSALxxxx Circuit 16833 R1 = 100 VS + VS C1 = 4.7 F C OUT GND VO GND R1 and C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously at a voltage below VO = 2.0 V by the external circuit. www.vishay.com 1 TSOP341..YA1 Vishay Semiconductors Absolute Maximum Ratings Absolute Maximum Ratings Tamb = 25 C, unless otherwise specified Symbol Value Supply Voltage Parameter (Pin 3) Test condition VS - 0.3 to + 6.0 V Supply Current (Pin 3) IS 3 mA Output Voltage (Pin 1) VO - 0.3 to (VS+ 0.3) V Output Current (Pin 1) IO 10 mA Tj 100 C Tstg - 25 to + 85 C Junction Temperature Storage Temperature Range Operating Temperature Range Unit Tamb - 25 to + 85 C Power Consumption (Tamb 85 C) Ptot 30 mW Soldering Temperature t 10 s, 1 mm from case Tsd 260 C Electrical and Optical Characteristics Tamb = 25 C, unless otherwise specified Parameter Supply Current (Pin 3) Symbol Min Typ. Max Ev = 0 Test condition ISD 0.7 1.2 1.5 Ev = 40 klx, sunlight ISH Supply Voltage VS Transmission Distance Ev = 0, test signal see fig.1, IR diode TSAL6200, IF = 250 mA Output Voltage Low (Pin 1) IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum Irradiance (30 - 40 kHz) VS = 3 V Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Ee min Minimum Irradiance (56 kHz) VS = 3 V Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Minimum Irradiance (30 - 40 kHz) 1.3 2.7 d Unit mA mA 5.5 35 V m 250 mV 0.2 0.4 mW/m2 Ee min 0.3 0.5 mW/m2 VS = 5 V Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Ee min 0.35 0.5 mW/m2 Minimum Irradiance (56 kHz) VS = 5 V Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Ee min 0.45 0.6 mW/m2 Maximum Irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee max Directivity Angle of half transmission distance www.vishay.com 2 1/2 30 W/m2 45 deg Document Number 82256 Rev. 1.1, 19-Apr-06 TSOP341..YA1 Vishay Semiconductors Typical Characteristics Tamb = 25 C unless otherwise specified Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, T = 10 ms) 1.0 t tpi *) T *) tpi 6/fo is recommended for optimal function Output Signal VO 1) 2) VOH VOL 14337 3/f0 < td < 9/f0 tpi - 4/f 0 < tpo < tpi + 6/f0 td1 ) t tpo2 ) Ton ,Toff - Output Pulse Width (ms) Ee 0.9 0.8 0.6 0.5 0.3 0.2 0.0 0.1 1.0 16910 10.0 100.0 1000.010000.0 Ee - Irradiance (mW/m2) Figure 4. Output Pulse Diagram E e min / E e - Rel. Responsivity 1.2 0.30 Output Pulse 0.25 0.20 0.15 Input Burst Duration 0.10 = 950 nm, optical test signal, fig.1 0.05 0.00 0.1 1.0 10.0 Ee - Irradiance (mW/m) 16907 1.0 0.8 0.6 0.4 f = f0 5 % f (3 dB) = f0/7 0.2 0.0 0.7 100.0 1000.0 10000.0 0.9 1.1 f/f0 - Relative Frequency 16926 Figure 2. Pulse Length and Sensitivity in Dark Ambient 1.3 Figure 5. Frequency Dependence of Responsivity Optical Test Signal 4.0 600 s t 600 s T = 60 ms 94 8134 Output Signal, (see Fig. 4) VOH VOL Ton Toff t Ee min - Threshold Irradiance (mW/m2 ) t po - Output Pulse Width (ms) = 950 nm, optical test signal, fig. 3 0.1 0.35 VO Toff 0.4 Figure 1. Output Function Ee Ton 0.7 3.5 3.0 2.5 2.0 1.5 Document Number 82256 Rev. 1.1, 19-Apr-06 Ambient, = 950 nm 1.0 0.5 0.0 0.01 16911 Figure 3. Output Function Correlation with ambient light sources: 10 W/m2 1.4 klx (Std.illum.A, T= 2855 K) 10 W/m2 8.2 klx (Daylight, T = 5900 K) 0.10 1.00 10.00 100.00 E - Ambient DC Irradiance (W/m 2) Figure 6. Sensitivity in Bright Ambient www.vishay.com 3 TSOP341..YA1 Vishay Semiconductors 0.6 f = fo 1.5 f = 10 kHz 1.0 f = 1 kHz 0.5 f = 100 Hz 16912 0.0 0.1 1.0 10.0 100.0 1000.0 VsRMS - AC Voltage on DC Supply Voltage (mV) 2.0 f(E) = f0 1.6 1.2 0.8 0.4 0.0 0.0 0.4 0.8 1.2 1.6 Figure 8. Sensitivity vs. Electric Field Disturbances Sensitivity in dark ambient 0.4 0.3 0.2 0.1 0.0 - 30 - 15 0 15 30 45 60 75 16918 Tamb - Ambient Temperature (C) 90 Figure 10. Sensitivity vs. Ambient Temperature 1.2 1.0 0.8 0.6 0.4 0.2 0.0 750 2.0 E - Field Strength of Disturbance (kV/m) 94 8147 0.5 S ( ) rel - Relative Spectral Sensitivity E e min- Threshold Irradiance (mW/m) Figure 7. Sensitivity vs. Supply Voltage Disturbances Ee min - Threshold Irradiance (mW/m) Ee min- Threshold Irradiance (mW/m) 2.0 850 950 1050 1150 - Wavelength (nm) 16919 Figure 11. Relative Spectral Sensitivity vs. Wavelength 0 10 20 1.0 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 1.0 0.6 0.5 0.9 50 0.8 60 0.4 0.3 f = 38 kHz, Ee = 2 mW/m2 0.2 70 0.7 0.1 80 0.0 0 16914 20 40 60 80 100 120 Burst Length (number of cycles/burst) Figure 9. Max. Envelope Duty Cycle vs. Burstlength www.vishay.com 4 0.6 96 12223p2 0.4 0.2 0 0.2 0.4 0.6 drel - Relative Transmission Distance Figure 12. Directivity Document Number 82256 Rev. 1.1, 19-Apr-06 TSOP341..YA1 Vishay Semiconductors 1.0 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 17185 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VS - Supply Voltage (V) IR Signal E e min - Sensitivity (mW/m 2 ) 0.9 * Continuous signal at 38 kHz or at any other frequency * Signals from fluorescent lamps with electronic ballast (an example of the signal modulation is in the figure below). IR Signal from fluorescent lamp with low modulation Figure 13. Sensitivity vs. Supply Voltage 0 Suitable Data Format The circuit of the TSOP341..YA1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpass filter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fulfill the following conditions: * Carrier frequency should be close to center frequency of the bandpass (e.g. 38 kHz). * Burst length should be 6 cycles/burst or longer. * After each burst which is between 6 cycles and 70 cycles a gap time of at least 10 cycles is necessary. * For each burst which is longer than 1.8 ms a corresponding gap time is necessary at some time in the data stream. This gap time should have at least same length as the burst. * Up to 2200 short bursts per second can be received continuously. Some examples for suitable data format are: NEC Code, Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, RCMM Code, R-2000 Code, RECS-80 Code. When a disturbance signal is applied to the TSOP341..YA1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occur. Some examples for such disturbance signals which are suppressed by the TSOP341..YA1 are: * DC light (e.g. from tungsten bulb or sunlight) Document Number 82256 Rev. 1.1, 19-Apr-06 16920 5 10 Time (ms) 15 20 Figure 14. IR Signal from Fluorescent Lamp with low Modulation www.vishay.com 5 TSOP341..YA1 Vishay Semiconductors Package Dimensions in mm 14399 www.vishay.com 6 Document Number 82256 Rev. 1.1, 19-Apr-06 TSOP341..YA1 Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Document Number 82256 Rev. 1.1, 19-Apr-06 www.vishay.com 7 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1