DS18S20+T&R - Hytronics - Datasheet.Live

AVAILABLE

Functional Diagrams

Pin Configurations appear at end of data sheet.

Functional Diagrams continued at end of data sheet.

UCSP is a trademark of Maxim Integrated Products, Inc.

For pricing, delivery, and ordering information, please contact Maxim Direct

at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.

FEATURES

 Unique 1-Wire® Int er face Requires Onl y O ne

P o r t P in for Co mmunication

 Each Dev ice has a Unique 64-Bit Serial Code

S to re d in an On-Boar d RO M

 Multidrop Capability Simplifies Distributed

Temperat u r e S ensing Appl icatio ns

 R equires No Exter nal Components

 Can Be Po w er ed fr om Data Line. Power

Supp ly Ra nge is 3.0V to 5.5V

 Measure s T emper atur es from -55°C to

+125°C (-67°F to +257°F)

 ±0.5°C Accuracy from -10°C to +85°C

 9-Bit Thermom ete r Resolution

 Co nverts Temperatur e in 750ms ( max)

 User-Definab le No nvolat ile (NV) Alarm

Settings

 Ala rm Se a rch Command Id e ntifie s and

Addresses De v ices Whose Temperatur e is

Outsid e P rogrammed Limits (T emper atur e

A l a rm C on dition )

 Applications Include T her mostat ic Co nt ro ls,

Indu strial Syste ms, Consu mer Products,

Thermometers, o r Any Ther mally Se nsitive

System

PIN CONFIGURATIONS

DESCRIPTION

The DS18S20 digital thermometer provides 9-bit Celsius temperature measurements and has an alarm

function with nonvolatile user-programmable upper and lower trigger points. The DS18S20

communicates over a 1-Wire bus that by definition requires only one data line (and ground) for

co mmu nicat io n with a ce ntral micro pro cesso r. It has an o perat ing t emperat ure r ange o f –55°C to +125°C

and is ac curat e to ±0.5°C o ver t he range o f –10°C to +85°C. In addit io n, t he DS18S20 can der ive power

d irectly from t he data line (“p ar asite po w er ”) , eliminating the need for an external power supply.

Each DS18S20 has a unique 64-bit ser ial code, whic h allo ws mu lt iple DS18S20s t o fu nc tio n o n t he sa me

1-Wire bus. Thus, it is simple to use one microprocessor to control many DS18S20s distributed over a

large area. Applications that can benefit from this feature include HVAC environmental controls,

temperature monitoring systems inside buildings, equipment, or machinery, and process monitoring and

con trol sy stems.

1-Wire is a regi stered trademark of Maxim Integrated Products, Inc.

TO-92

(DS18S20)

(BOTTOM VIE W)

MAXIM

DS1820

GND

SO ( 150 mil s)

(DS18S20Z)

N.C.

GND

N.C.

DS1820

19-5474; Rev 8/10

DS18S20

High-Precision 1-

Wire Digital Thermometer

DS18S20

2 of 23

ORDERING INFORMATION

PART

TEMP RANGE

PIN-PACKAGE

DS18S20

–55°C to +125°C

3 TO-92

DS18S20+

–55°C to +125°C

3 TO-92

DS18S20/T&R

–55°C to +125°C

3 TO-92 (2000 P iece)

DS18S20+T&R

–55°C to +125°C

3 TO-92 (2000 P iece)

DS18S20-SL/T&R

–55°C to +125°C

3 TO-92 (2000 P iece)*

DS18S20-SL+T&R

–55°C to +125°C

3 TO-92 (2000 P iece)*

DS18S20Z

–55°C to +125°C

8 SO

DS18S20Z+

–55°C to +125°C

8 SO

DS18S20Z/T&R

–55°C to +125°C

8 SO (2500 Piece)

DS18S20Z+T&R

–55°C to +125°C

8 SO (2500 Piece)

+Denotes a lead(Pb)-free/RoHS-compliant package. A “+” appears on t he to p mark of le ad(Pb)-f re e pac k ages .

T&R = Tape and reel.

*TO-92 pack ages in ta pe an d re el ca n be or der ed w ith s tra ight or fo rmed lea ds. Ch oose “ SL ” for s tra ight leads . B ulk TO -92 or de rs are s t raigh t

leads only.

PIN DESCRIPTION

PIN NAME FUNCTION

TO-92 SO

1 5 GND Ground

2 4 DQ

Data Inp ut/ Outp ut. Op e n-dr ain 1 -Wire interface pin. Also p r ovid es

power to the devi ce whe n used in parasite power mode (see the

Powering the DS18S20 section.)

3 3 VDD

O p tional V

. V

must be grounded for o per at io n in parasite

po wer mo de.

—

1, 2, 6, 7,

8 N.C. No Connection

OVERVIEW

Figure 1 shows a block diagram of the DS18S20, and pin descriptions are given in the Pin Description

t able. The 64-bit ROM stores the device’ s unique serial code. The scratchpad memo ry co nt ains the 2-byte

t emper atu re reg ister t hat stor es the d ig it a l out put fro m t he te mper at ure senso r. In addit io n, t he scrat chpad

provides access to the 1-byte upper a nd low er alarm trigg er registers (T H a nd TL) . The TH and TL registers

are non vo lat ile (EE PROM) , so t hey will retain data when t he device is po wer ed do wn.

The DS18S20 uses Maxim’s exclusive 1-Wire bus protocol that implements bus communication using

one co ntrol signal. The control line require s a weak pullup resistor since all devices are linked to the bus

via a 3-state or open-drain port (the DQ pin in the case of the DS18S20). In this bus system, the

micro p ro cesso r (the mast er dev ice) identifies and addr esses de v ices on the bus using each de vice’s unique

64-bit code. Because each device has a unique code, the number o f devices t hat can be addressed on one

bus is virtually unlimited. The 1-Wire bus pr otocol, including det a iled explanatio ns o f the commands and

“t ime slots,” is covered in the 1-Wire Bus S yst e m section.

Another feature of the DS18S20 is the ability to operate without an external power supply. Power is

instead supplied through the 1-Wire pullup resistor via the DQ pin when the bus is high. The high bus

signal also charges an internal capacitor (CPP), whic h then supplies po wer to the device w hen t he bus is

low. This method of deriving power from the 1-Wire bus is referred to as “parasite power.” As an

alt er native , the DS1 8S 20 may als o be pow er ed by a n exte rnal s upply on V DD.

DS18S20

3 of 23

Figure 1. DS18S20 Block Diagram

OPERATION—MEASURING TEMPERATURE

The core fu nct ionality of t he DS18S20 is it s direc t-to-dig it al temperature sensor. The temperatur e sensor

output has 9-bit resolution, which corresponds to 0.5°C steps. The DS18S20 powers-up in a low-power

idle st at e; to init iat e a t emperat ur e measure ment and A-to-D co nver sio n, t he mast er mu st issue a Co nvert

T [44h] command. Following the conversion, the resulting thermal data is stored in the 2-byte

temperat ure register in the scrat chpad memor y and the DS18S20 ret ur ns t o it s idle state. If the DS18S20

is powered by an external supply, the master can issue “read-time slots” (see the 1-Wire Bus System

section) after the Convert T command and the DS18S20 will respond by transmitting 0 while the

t emperat ur e convers io n is in prog r ess and 1 whe n the convers io n is do ne. If the DS18S2 0 is po wer ed wit h

parasite power, this notificat ion technique cannot be used since the bus must be pulled high by a strong

pu llup during the entir e temp er atur e conversion. T he bus require ment s for p ar as ite power are explained in

detail in the Powering the DS18S20 section.

The DS18S20 out put data is ca librated in degrees cent igrade; fo r Fahr enheit applicatio ns, a lookup table

or conversion routine must be used. The temperature data is stored as a 16-bit sign-extended two’s

complement number in the temperature register (see Figure 2). The sign bits (S) indicate if the

temperature is positive or negative: for posit ive numbers S = 0 and for negative numbers S = 1. Table 1

gives examples of digital output data and the corresponding temperature read ing.

Reso lu t io ns great er t han 9 bits can be ca lculat ed using t he dat a fro m t he t e mp erat ure, COUNT RE MAI N

and COUNT PER °C registers in t he scratchpad. Note that the COUNT PE R °C register is hard-w ir e d to

16 (10h). After reading the scratchpad, the TEMP_READ value is obtained by truncating the 0.5°C bit

(bit 0) from the temperature data (see Figure 2). The extended resolution temperature can then be

calculat ed using the follow ing equation:

CPERCOUNT REMAINCOUNTCPERCOUNT

READTEMPETEMPERATUR __ ___

25.0_ −

+−=

4.7k

POWER-

SUPPLY

SENSE

64-BIT ROM

AND

1-Wir e POR T

VDD

INTERNAL V

PARASITE POWER

CIRCUIT

MEMORY CONTROL

LOGIC

SCRATCHPAD

8-BIT CRC GENERATOR

TEM PERATU RE SENS OR

ALARM HIGH TRIGGER (T

)

ALARM LOW TRIGGER (T

)

GND

DS18S20

4 of 23

Figure 2. Tem p eratu r e Register Format

BIT 7

BIT 6

BIT 5

BIT 4

BIT 3

BIT 2

BIT 1

BIT 0

L S BYTE

26 25 24 23 22 21 20 2-1

BIT 15

BIT 14

BIT 13

BIT 12

BIT 11

BIT 10

BIT 9

BIT 8

MS BYT E

S S S S S S S S

S = SIGN

Table 1. Temperatur e/D ata Relationsh ip

TEMPERATURE

(

C) DIG ITAL OUTPUT

(BINARY) DIGITA L O U TPUT

(HEX)

+85.0*

0000 0000 1010 1010

00AAh

+25.0 0000 0000 0011 0010 0032h

+0.5

0000 0000 0000 0001

0001h

0000 0000 0000 0000

0000h

-0.5

1111 1111 1111 1111

FFFFh

-25.0

1111 1111 1100 1110

FFCEh

-55.0

1111 1111 1001 0010

FF92h

*The power-on reset value of the temperature register i s +85°C.

OPERATION—ALARM SIGNALING

After the DS18S20 performs a temperature conversion, the temperature value is compared to the user-

defined two’s complement alarm trigger values stored in the 1-byte TH and TL registers (see Figure 3).

The s ig n bit ( S) in d ic at e s if the va lu e is pos itive o r negative: for posit ive numbers S = 0 and for negative

numbers S = 1. The TH and TL registers are nonvolatile (EEPROM) so they will retain data when the

device is po wered do wn. T H and T L can be access ed t hrough byt e s 2 and 3 o f t he scr at chpad as e xp laine d

in the Memory section.

Figure 3. TH and TL Register Format

BIT 7

BIT 6

BIT 5

BIT 4

BIT 3

BIT 2

BIT 1

BIT 0

S 26 25 25 25 22 21 20

Only bits 8 through 1 of the temperature register are used in the TH and TL compar ison since TH and TL

are 8-bit registers. If the measured temperature is lo we r t han or equa l t o TL or higher than TH, an alar m

condit ion exists and an alarm flag is set inside the DS18S20. This flag is updated a ft er ever y t e mper atur e

measurement; therefore, if the alarm condition goes away, the flag will be turned off after the next

temper atur e conversion.

The mast er dev ice can c heck the alar m flag st atus o f all DS18S20s on t he bus by issuing an A lar m Sear ch

[ECh] command. Any DS18S20s with a set alarm flag will respond to the command, so the master can

deter mine exact ly which DS18S20s ha ve experienced an alarm condition. If an alar m co ndition e xist s and

t he T H or TL sett ings have c ha nged , a not her t emp era ture conver s io n s hould be do ne to va lida te t he ala r m

condition.

DS18S20

5 of 23

POWERING THE DS18S20

The DS18S20 can be powered by an e xter nal supply on the VDD pin, or it ca n o perat e in “paras ite power ”

mode, which allows the DS18S20 to function without a local external supply. Parasite power is very

useful for applications that require remote temperature sensing or those with space constraints.

Figure 1 shows the DS18S20’s parasite-power control circuitry, which “steals” power from the 1-Wire

bus via the DQ pin when the bus is high. The stolen charge powers the DS18S20 while the bus is high,

and so me o f t he charge is st ored on t he parasite po wer capacit or (CPP) to pro vide power when t he bus is

low. Whe n t he DS18S 20 is used in parasite power mo d e, t he VDD pin must be conne cte d to g r ound .

In parasite power mode, the 1-Wire bus and CPP can provide sufficient current to the DS18S20 for most

operations as long as the specified timing and voltage requirements are met (see the DC Electrical

Characteristics and the AC Electrical Characteristics). However, when the DS18S20 is performing

t emper atu re convers io ns o r copying data fro m the scrat chpad me mo r y to EEPROM, the oper at ing cur rent

can be as high as 1.5mA. This current can cause an unacceptable voltage drop across the weak 1-Wire

pu llup res ist or and is more cur r ent than can be supplied by CPP. T o assure that t he DS18S 20 ha s suf fi cient

supply current, it is necessary to provide a strong pullup on the 1-Wire bus whenever temperature

conversions are taking place or data is being copied from the scratchpad to EEPROM. This can be

accomplished by using a MOSFET to pull the bus directly to the rail as shown in Figure 4. The 1-Wire

bus must be sw it ched to t he strong pullup w it hin 1 0µs (ma x) a fter a Convert T [44h] or Copy Scratchpa d

[48h] comma nd is issued, and t he bus must be held high by t he pu llup for the duration of t he conve rsion

(tCONV) or data transfer (tWR = 1 0ms). No o ther act iv ity ca n t ake place on t he 1-Wire bu s w h i le the pullup

is enab le d.

The DS18S 20 can also be powered by the conventional metho d of connecting an exter nal power supp ly to

the VDD pin, as shown in Figure 5. The advantage of this method is that the MOSFET pullup is not

requir ed , and the 1-Wire bus is free t o car r y other traffic during the temperat u r e conver sion time.

The use of parasite po w er is not recommended for temp er atur es above 1 00 °C since the DS18S20 may not

be able to sust ain communicat io ns due t o t he higher leakage cur rents t hat can e xist at t hese te mperat ur es.

For applicat ions in which suc h t emperat ures are likely, it is strongly reco mmended that the DS18S20 be

po wered by an ext er nal power supply.

In so me sit uat ions t he bu s ma st er ma y no t know whet her t he DS 18S2 0s o n t he bus ar e par asit e p ow er ed

o r powere d by ext ernal sup plies. The mast er need s t his in fo r mat ion t o det er mine if t he st ro ng bus p u llup

shou ld be used during temperat ur e co nversions. To g et t h is information, the mast er can issue a Skip ROM

[CCh] command followed by a Read Power Supply [B4h] command followed by a “read-time slot”.

During the read-time slot, parasite powered DS18S20s will pull the bus low, and externally powered

DS18S20s will let the bus re main hig h. I f t he bus is pu lled lo w, t he master knows t hat it must supp ly the

strong pullup o n t he 1-Wire bus dur ing temperat ure conversions.

DS18S20

6 of 23

Figure 4. Supplying the Parasite-Pow er ed DS18S 20 During Temperature Conversions

Figure 5. Powering the DS18S20 with an External Supply

64-BIT LASERED ROM CODE

Each DS18S20 co ntains a uniqu e 64-bit code (see Figure 6) stor ed in ROM . The leas t signif icant 8 b its of

the ROM code contain the DS18S20’s 1-Wire family code: 10h. The next 48 bits contain a unique ser ia l

numb er . The mos t sign ificant 8 bit s contain a cyclic redundancy check (CRC) byte t hat is calculat ed from

the first 56 bits of the ROM code. A detailed explanation of the CRC bits is provided in the CRC

Generation section. The 64-bit ROM code and associated ROM function control logic allow the

DS18S20 to opera te as a 1-Wire device using the protocol detailed in the 1-Wir e Bus S yst e m section.

Figure 6. 64-Bit Lasered ROM Code

8-BIT CRC

48-BIT SERIAL NUMBER

8-BIT FAMI LY CODE (10h)

4.7k

1-Wire BUS

DS18S20

GND

TO OTHER

1-WIRE DEVICES

(EXTER NAL SUPPL Y)

DS18S20

GND

4.7k

TO OTHER

1-WIRE DEVICES

1-Wire BUS

MSB

LSB

MSB

DS18S20

7 of 23

MEMORY

The DS18S20’s memory is organized as shown in Figure 7. The memory consists of an SRAM

scratchpad with nonvolatile EEPROM storage for the high and low alarm trigger registers (TH and TL).

Note t hat if the DS18S2 0 alarm fu nction is not used, the TH and TL registers can ser ve a s general-purpose

memory. All memo ry commands ar e des c ribe d in detail in the DS18S20 Function Commands section.

Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,

respect ivel y. T hese byt es are read-o nly. Byt e s 2 and 3 provide access to TH and T L reg isters. Bytes 4 and

5 are r es er ved for inte rnal use b y the dev ice and c annot be ove rw rit te n; these byt es wil l re tu rn all 1s when

read. Bytes 6 a nd 7 co ntain t he COUNT REMAI N and CO UNT PER ºC registers, which can be u sed to

calculat e ext ended r esolution resu lts as exp lained in the Operation—Measuring Temperature section.

Byte 8 of t he scr atchpad is read-on ly a nd c o nt ai ns the C R C code fo r byt e s 0 through 7 o f t he scratchpad.

The DS18S20 generates this CRC using the method described in the CRC Generation section.

Data is written to bytes 2 and 3 of the scratchpad using the Write Scratchpad [4Eh] command; the data

must be transmitted to the DS18S20 starting with the least significant bit of byte 2. To verify data

integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is

written. When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least

signif ica nt bit of byte 0. T o transfer the TH and T L data from the scratchpad t o EEP ROM, t he mast er must

issue t he Co py Scr atchpad [48h] command.

Data in t he EEPROM registers is reta ined when t he de vic e is power ed down; at power-up t he EE PROM

dat a is r eload ed into the corresponding scratchpad locations. D ata ca n also be reloaded fr om EEP ROM to

the scratchpad at any time using the Recall E2 [B8h] command. The master can issue “read-time slots”

(see t he 1-Wire B us Sy ste m sect io n) follo w ing t he Reca ll E2 command and t he DS18S20 w ill indicate t he

st atu s of the reca ll by tr ansmitting 0 while t he recall is in pro g r ess and 1 when the reca ll is done.

Figure 7. DS18S20 Memory Map

SCRATCHPAD

(POWER-UP STATE)

Byte 0 Temperature LSB (AAh)

Byte 1 Temperat ur e MSB (00h) EEPROM

Byte 2 TH Reg ister o r User B yte 1* TH Reg ister o r User B yte 1

Byte 3 TL Register or User Byte 2* TL Reg ist er o r User Byte 2

Byte 4 Reserved (FFh)

Byte 5 Reserved (FFh)

Byte 6 COUNT RE MAIN (0Ch)

Byte 7 COUN T PER °C (1 0h)

Byte 8 CRC*

Power-up st ate depends on value(s) stored i n EEPROM.

(85°C)

DS18S20

8 of 23

CRC GENERATION

CRC byt es are provided as p art of the DS18S20’s 64-bit ROM co de a nd in t he 9t h byt e of t he scrat chpad

memory. The ROM co de CRC is ca lcu lat ed fro m t he first 5 6 b it s of t he ROM cod e and is co nt ained in t he

most significant byte of the ROM. The scratchpad CRC is calculated from the data stored in the

scrat chpad, and t here fore it changes when the data in the scratchpad chang es. The CRCs pro vide the bus

mast er with a method o f data validation when data is read fr om the DS18S2 0. To ver ify that data has been

read correctly, the bus master must re-calculate the CRC from the received data and then compare this

value to eit her the ROM co de CRC ( for ROM reads) or to the scrat chpad CRC ( for scrat chpad reads). If

t he calcu lated CRC mat ches the read C RC, the dat a ha s been rece ived err or free. T he comparison of CRC

values a nd t he dec ision to co ntinue w it h a n oper ation are det er mined e nt ir ely by t he bus mast er. T here is

no circuitry inside the DS18S20 that prevents a command sequence from proceeding if the DS18S20

CRC (ROM or scr atchpad) d oes not mat ch t he va lue generat ed by the bus mast er .

T he equivalent p olynom i al f unction of the C RC (ROM or s cr atc hpad) is:

CRC = X8 + X5 + X4 + 1

The bus master can re-calcu lat e the CRC and compare it to the CRC valu es from the DS18S20 using t he

po lyno mial generator shown in Figure 8. This circuit consists of a shift register and XOR gates, and the

shift register bits are init ialized to 0. Starting with the least significant bit o f the ROM code or the least

significant bit of byte 0 in the scratchpad, one bit at a time should shifted into the shift register. After

shifting in the 56th bit from the ROM or the most significant bit of byte 7 from the scratchpad, the

po lyno mial generator will cont ain the re-calculated CRC. Next, the 8-bit ROM code or scratchpad CRC

from the DS18S20 must be shifted into the circuit. At this po int, if the re-calcu lat ed CRC was corr ect, the

sh ift re gis ter w ill contain all 0s . Ad ditional info rm a tio n abou t t he M axim 1-Wire cyclic redundancy check

is available in Application Note 27: Understanding and Using Cyclic Redundancy Checks with Maxim

iButton Products.

Figure 8. CRC Generator

(MSB) (LSB)

XOR XOR

XOR

INPUT

DS18S20

9 of 23

1-WIRE BUS SYSTEM

The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS18S20 is

always a slave. When there is only one slave on the bus, the system is referred to as a “single-drop”

s ys tem; the sys tem is “multid rop ” if t he re a re multiple s laves on the bu s .

All data and commands are t r ansmitted least signif ica nt bit f irst ov er the 1-Wire bus.

The following discussion of the 1-Wire bus system is broken down into three topics: hardware

co nfiguration, transaction sequence, a nd 1-Wire signaling (sig nal types and timing) .

HARDWARE CONFIGURATION

The 1-Wire bus has by definit io n only a single data line. Each device (master or slave) interfaces to the

data line via an open drain or 3-state port. This allows each device to “release” the data line when the

device is no t t ransmitt ing data so t he bus is available for use by another device. The 1-Wire port of the

DS1 8S 20 ( the DQ p in) is ope n dr ain with a n internal cir cuit eq ui valent to tha t shown in Figure 9.

The 1-Wire bus requires an external pullup resistor of approximately 5kΩ; thus, the idle state for the

1-Wire bus is high. If for any r eason a trans action ne eds to be s uspend e d, the bus M US T be left i n the idl e

state if the transaction is to resume. Infinite recovery time can occur between bits so long as the 1-Wire

bus is in the inact ive ( hig h) st ate during the reco very period. If t he bus is held low fo r more t han 480µs,

all c omponents on t he bus wi ll be reset.

Figure 9. Hardware Configuration

4.7k

5μA

TYP

DS18S20 1-Wire PORT

100

Ω

MOSFET

Rx = RECEIVE

Tx = TRANSMIT

1-Wire BUS

DS18S20

10 of 23

TRANSACTION SEQUENCE

The t r ansaction sequence for access ing the DS18S20 is as fo llows:

S tep 1. Initialization

S tep 2. ROM Command (follo wed by an y required data exchange)

S tep 3. DS18S20 Function Comma nd ( followed by any r equired dat a exchange)

I t is very im porta nt t o follow th is se qu ence every time the DS18S20 is acces sed, a s t he DS18S 20 w i ll not

respond if any steps in the sequence are missing or out of order. Exceptions to this rule are the Search

ROM [F0h] and Alarm Search [ECh] commands. After issuing either of these ROM commands, the

master must r eturn to Step 1 in the seque nce.

INITIALIZATION

All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence

consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the

sla ve(s). T he presence pulse let s the bus master kn ow that slave devices ( such as t he DS18S 20 ) ar e on t h e

bus a nd are read y t o op erate. T iming for t he re set and pre se nce pu lses is det a iled in t he 1-Wire Sign aling

section.

ROM COMMANDS

After the bus master has detected a presence pulse, it can issue a ROM command. These commands

operate on the unique 64-bit ROM co des of each sl ave de vice a nd a llow the mast er to single o ut a specific

device if many are present on the 1-Wire bus. These co mmands also allow the ma ster to determine how

many and what types of devices are present on the bus or if any device has experienced an alarm

condition. There are five ROM commands, and each command is 8 bits long. The master device must

issue an appropriate ROM command before issuing a DS18S20 function command. A flowchart for

op er ation of the R OM c ommands is shown in Figure 14.

SEARCH ROM [F0h]

When a system is initially powered up, the master must identify the ROM codes of all slave devices on

the bus, which allows the master to determine the number of slaves and their device types. The master

learns t he ROM codes t hrough a process o f elimination that r eq uires the ma ster to per for m a Search RO M

cycle ( i. e. , Sear ch RO M co mma nd fo llo wed b y d at a exchange) as many t imes as neces sar y t o ide nt ify al l

of t he slave devices. If t here is o nly one slave on t he bus, the simpler Read ROM co mmand (see be low )

can be used in place of the Search ROM process. For a detailed explanation of the Search ROM

procedure, refer to the iButton® Book of Standards at www.maxim-ic.com/ibuttonbook. After every

Search ROM cyc le, the bu s mast er must ret ur n to St ep 1 (Initia lization) in the t r ansact io n sequ ence.

READ ROM [33h]

This co mmand ca n o nly be used when there is one slave o n the bu s. It allo ws the bu s mast er to read the

s la ve ’ s 6 4-bit ROM code w it ho ut using t he Se arch ROM procedure. I f t his command is us ed when there

is more than one slave present on the bus, a data collision will occur when all the slaves attempt to

respond at the same t ime.

MATCH ROM [55h]

The match ROM co mmand follo wed by a 64-bit ROM code sequence allow s the bus master to address a

specific slave device on a multidrop or single-drop bus. Only the slave that exactly matches the 64-bit

ROM code sequence will respond to the function command issued by the master; all other slaves on the

bus will wa it fo r a r eset p ulse.

iButton is a registered trademark of Maxim Integrated Products, Inc.

DS18S20

11 of 23

SKIP ROM [CCh]

The master can use this co mmand to address all devices on the bus simultaneously without sending out

any ROM code information. For example, the master can make all DS18S20s on the bus perform

simultaneous temperature convers io ns by issuing a Skip ROM co mmand fo llowed by a Convert T [44h]

command.

Note that the Read Scratchpad [BEh] command can follow the Skip ROM command only if there is a

single slave device on the bus. In this case, time is saved by allowing the master to read from the slave

without sending the device’s 64-bit ROM code. A Skip ROM command followed by a Read Scratchpad

command wil l ca us e a data coll ision on the bus i f there is mor e th an one slave sin ce multiple devices wi ll

attempt to transmit data simultan eously.

ALARM SEARCH [ECh]

The operation of this command is identical to the operation of the Search ROM command except that

only slaves with a set alarm flag will respond. This command allows the master device to determine if

any DS18S20s experienced an alarm condition during the most recent temperature conversion. After

every A lar m S earc h c ycle ( i. e., Alar m Search co mmand fo llo wed by d at a exc ha nge), t he bus ma st er must

return to Step 1 (Init ialization) in the transaction sequence. See the Operation—Alarm Signaling section

for an e xpla natio n o f alar m flag op er ation.

DS18S20 FUNCTION COMMANDS

After the bus master has used a ROM command to address the DS18S20 with which it wishes to

communicate, t he mast er can issue o ne o f t he DS18S20 funct ion co mma nd s. These co mmands allow the

mast er to write to and read from the DS18S 20 ’ s s cratchpad memory, initiat e te mperat ur e convers io ns and

determine the power supply mode. The DS18S20 function commands, which are described below, are

su mma r iz ed in Table 2 and il lustr ated b y the flowchart in Figure 15.

CONVERT T [44h]

This co mmand init iates a single temperature convers io n. Follo w ing t he c onvers io n, t he resu lt ing t he r ma l

dat a is st or ed in t he 2-byt e t emperat ur e register in t he scratchpad memo r y and t he DS18S20 r et urns to it s

low-power idle state. If the device is being used in parasite power mode, within 10µs (max) after this

command is issued the master must enable a strong pullup on the 1-Wire bus for the duration of the

co nvers io n (t CONV) as descr ibed in the Powe ring the DS18S20 section. I f the DS18S20 is powered by an

ext erna l su pp ly, t he ma ster can issue read-time slot s aft er t he Co nvert T co mma nd a nd the DS18S 20 wi ll

respond by transmitt ing 0 while the temperature conversion is in progress and 1 when t he conversio n is

done. In parasite power mode this notification technique cannot be used since the bus is pulled high by

t he st ro ng pullup dur ing the conversion.

WRITE SCRATCHPAD [4Eh]

This command allows the master to write 2 bytes of data to the DS18S20’s scratchpad. The first byte is

wr itt en int o t he T H reg ist er (byte 2 o f the scrat chpad), and t he second byte is writt en into t he T L register

(byte 3 of the scratchpad). Data must be transmitted least significant bit first. Both bytes MUST be

written be fore the mast er issues a r eset, or the data may be cor r u pt ed.

READ SCRAT CHPAD [BEh]

This co mmand allo ws t he ma ster to read t he contents of the scratchpad. The data transfer starts w it h t he

least significant bit of byte 0 and continues through the scratchpad until the 9th byte (byte 8 – CRC) is

read. The master may issue a reset t o ter minate reading at any t ime if only part of the scrat chpad d at a is

needed.

DS18S20

12 of 23

COPY SCRATCHPAD [48h]

This co mmand cop ies the cont ents of the scrat chpad TH and TL r egist ers (byt es 2 and 3) to E EPROM. I f

the device is being used in parasite power mode, within 10µs (max) after this command is issued the

master mu st enable a strong pu llup on the 1-Wire bus fo r at least 10ms as descr ibed in the Powe rin g the

DS18S20 section.

RECALL E2 [B8h]

T his comma nd r ec a lls t he ala r m tr igg e r va lu e s ( T H and TL) fr o m E EP ROM and p laces t he dat a in bytes 2

and 3, respect ively, in the scratchpad memo ry. The mast er device can issue read-time s lo t s follo w in g t he

Recall E2 command and the DS18S20 will indicate the status of the recall by transmitting 0 while the

recall is in progr ess a nd 1 w hen t he reca ll is do ne . The recall operat io n happe ns aut omat ic ally at power-

up, so valid dat a is avai la ble in the scratchpad as soon as power is applied to the device.

READ POWER SUPPLY [B4h]

The mast er dev ice issues this command fo llowed by a read-t ime slot to determine if any DS18S20 s on the

bus are using par as ite power. D uring the read-time slot, parasite powered DS18S20s will pu ll t he bus lo w,

and externally powered DS18S20s will let the bus remain high. See the Powering the DS18S20 section

for usage info rmation for this comma nd.

Table 2. DS18S20 Function Command Set

COMMAND DESCRIPTION PROTOCOL

1-Wire BUS ACTIVITY

AFTER COMM AND IS

ISSUED

NOTES

TEMPERATURE CONVERSION COM MANDS

Convert T

Initiates temperature

conversion. 44h

DS18S20 tran smits conv ersion

st atu s to mast er ( not applicable

for p ar as ite-powered

DS18S20s).

MEMORY COM MANDS

Read

Scratchpad

Reads t he ent ire

scratchpad including the

CRC byt e . BEh

DS18S20 transmits up to 9

dat a b yt es to ma ster. 2

Write

Scratchpad

Writ es data int o

scratchpad bytes 2 and 3

(TH and TL).

4Eh

Master t r ansmits 2 data bytes

to DS18S20. 3

Copy

Scratchpad

Copies T

and T

data

fr om the scrat chpad to

EEPROM.

48h

None

Recal l E

Recal ls T

and T

data

from EEPROM to the

scratchpad.

B8h

DS18S20 tran smits recall

status to master.

Read Power

Supply

S ignals DS18S20 power

supply mode to the

master.

B4h

DS18S20 tran smits supply

status to master.

Note 1:

For par a sit e-powered DS18S20s, the m aster must enabl e a strong pullup on the 1-Wire bus during tempe rature

conver sions and copies from the scratch pad to EEPROM. No oth er bus activity may take place during this time.

Note 2:

The master can interrupt the transmission of data at any time by issuin g a reset.

Note 3:

Both byt es must be written befor e a reset is issued.

DS18S20

13 of 23

1-WIRE SIGNALING

The DS18S20 uses a strict 1-Wire co mmunication protocol to ensure data integrity. Several signal types

are defined by this protocol: reset pulse, presence pulse, write 0, write 1, read 0, and read 1. All these

signa ls, with the exception of the prese nce pu lse, are initiat ed b y t he bus master.

INIT IALIZATION PROCEDURE—RESET AN D PRESENCE PULSES

All co mmunicat io n w ith t he DS18S20 beg ins with an in it ia liz at ion sequen ce that co nsist s of a reset pu lse

from the master fo llowed by a presence pulse from the DS18S20. This is illustrated in Figure 10. Whe n

the DS18S20 sends the presence pulse in response to the reset, it is indicating to the master that it is on

the bus and r eady to operate.

Dur ing t he init ializatio n sequ ence t he bu s master transmits (T X) t he reset pu lse by pu lling t he 1-Wire bus

low for a minimum of 480µs. The bus master then releases the bus and goes into receive mode (RX).

When t he bus is released, the 5kΩ pullup re sist o r pu lls t he 1-Wire bus high. When the DS18S20 detects

this rising edge, it wait s 15µs to 60µs and then transmit s a presence pulse by pu lling t he 1-Wire bus low

for 60µs to 240µs.

Figure 10. Initializati on Timing

READ/WRITE TIME SLOTS

The bus master writes data to the DS18S20 during write time slots and reads data from the DS18S20

dur ing read-t ime slots. One bit o f data is t r ansmitted over t he 1-Wire bus per time slo t.

WRITE TIME SLOTS

There are two types of write time slots: “Write 1” time slots and “Write 0” time slots. The bus master

uses a Wr it e 1 time slo t to wr it e a lo g ic 1 t o t he DS18S20 and a Write 0 time slo t to wr it e a lo g ic 0 to t he

DS18S20. All wr it e time slot s must be a minimum o f 60µs in dur atio n with a mini mum of a 1µs recovery

t ime bet ween ind ivid ua l wr it e s lo t s. Bo t h type s o f wr it e t ime s lot s a re init iat ed by the mast er pu llin g t he

1-Wire bus low (see Figure 11).

To generat e a Writ e 1 t ime slo t , after p ulling t he 1-Wire bus lo w, t he bus mast er mu st r elease t he 1-Wire

bus wit hin 15µs. When the bus is relea sed, the 5kΩ pullup resistor will pull the bus high. To generate a

Write 0 time slo t, aft er pulling the 1-Wire bus low, t he bu s ma st er mu st co nt inue t o ho ld the bus low for

the duration of the time slot (at least 60µs). The DS18S20 samples t he 1-Wire bu s dur ing a w ind ow t hat

lasts from 15µs to 6 0 µs after the master initiat es the write time slot . If the bus is high during t he sa m pling

wind ow, a 1 is w ritte n to the DS18S20. I f the line is low, a 0 is writ ten to the DS18S20.

LINE TYPE LEGEND

Bus master pulling low

DS 18S20 pull ing low

Resistor pul lu p

VPU

GND

1-WIRE BUS

480µs minimum

DS18S20 T

presence pulse

60-240

MASTER T

RESET PULSE

MASTER R

DS18S20

waits 15-60

DS18S20

14 of 23

READ-TIME SLOTS

The DS18S 20 ca n on ly tr ansmit dat a to the mast er whe n the mast er issues r ead-time s lo t s. T he r e fo r e , t he

master must generat e read-time slots immed iately a ft er issuing a Read Scratchpad [BE h] or Read Power

Supp ly [B4h] co mmand, so t hat the DS18S20 can pro vide t he r equested dat a. In addition, t he mast er can

generat e read-t ime slo t s a ft er iss u ing Conve r t T [ 44 h] or Re ca ll E 2 [ B8h] co mma nds t o find o ut the st at us

of the operation as expla ined in the DS18S20 Function Commands section.

All read-time slots must be a minimum of 60µs in duration with a minimum of a 1µs recovery time

between slots. A read-time slot is initiated by the master device pulling the 1-Wire bus low for a

minimum o f 1µs a nd t hen r e lea sin g t he bus ( see Figure 11) . Aft er the ma ster init iates t he r ead-time slot,

t he DS18S20 w ill beg in t ransmit t ing a 1 or 0 on bus. T he DS18S20 t ransmits a 1 by lea ving t he bus hig h

and t ransmit s a 0 by pulling t he bus low. When transmitting a 0, t he DS18S20 will re lease t he bus by the

end of the time slot, and the bus will be pulled back to its high idle state by the pullup resister. Output

data from t he DS18S20 is valid for 15µs after t he fall ing edge t hat initiated the read-t ime s lo t . T herefore,

t he master must r elease t he bus and the n samp le t he bus st ate wit hin 15µs from the start of the slot.

Figure 12 illustrates that the sum of TINIT, TRC, and TSAMPLE must be less t han 15µs for a read-time slot.

Figure 13 shows that system timing margin is maximized by keeping TINIT and TRC as short as possible

and by locating the mast er sample time dur ing read -time slots to war d s the end of the 15µs perio d.

Figure 11. Read/Write Time Slot Timing Diagram

VPU

GND

1-WIRE BUS

60µs < T

“0” < 120µs

s < TREC < ∞

DS18S20

Samples

MIN TYP MAX

15µs

30µs

> 1

MASTER WRITE “0” SLOT

MASTER WRITE “1” SLOT

VPU

GND

1-WIRE BUS

15µs

MASTER READ “0” SLOT

MASTER READ “1” SLOT

Master samples

START

OF SLOT

START

OF SLOT

> 1

s < TREC < ∞

15µs

30µs

DS18S20 Samples

MIN TYP MAX

> 1µs

LINE TYPE LEGEND

Bus master pulling low DS 18S20 pull ing low

Resis tor pull up

DS18S20

15 of 23

Figure 12. Detailed Master Read 1 Timing

Figure 13. Reco mmended Master Read 1 Timing

GND

1-WIRE B US

15µs

VIH of Master

INT

> 1µs

Master samples

LINE TYPE LEGEND

Bus master pulling low

Resistor pul lu p

GND

1-WIRE B US

15µs

VIH of Master

small

INT

small

Master samples

DS18S20

16 of 23

Figure 14. ROM Commands Flowchart

CCh

SKIP ROM

COMMAND

MASTER TX

RESET PULSE

DS18S20 T

PRESENCE

PULSE

MASTER T

ROM

COMMAND

33h

READ ROM

COMMAND

55h

MATCH ROM

COMMAND

F0h

SEARCH ROM

COMMAND

ECh

ALARM SEARCH

COMMAND

MASTER T

BIT 0

DS18S20 T

BIT 0

DS18S20 TX BIT 0

MASTER TX BIT 0

BIT 0

MATCH?

MASTER TX

BIT 1

MATCH?

BIT 63

MATCH?

MASTER T

BIT 63

Y Y Y Y Y

DS18S20 TX BIT 1

MASTER T

BIT 1

DS18S20 TX BIT 63

MASTER TX BIT 63

BIT 0

MATCH?

BIT 1

MATCH?

BIT 63

MATCH?

DS18S20 TX

FAMILY CODE

1 BYTE

DS18S20 TX

SERIAL NUMBER

6 BYTES

DS18S20 TX

CRC BYTE

DS18S20 TX BIT 0

MASTER TX BIT 0

DEVICE(S)

WITH ALARM

FLAG SET?

Initialization

Sequence

MASTER TX

FUNCTION

COMMAND

(FIGURE 15)

DS18S20

17 of 23

Figure 15. DS18S20 Function Commands Flowchart

MASTER TX

FUNCTION

COMMAND

44h

CONVERT

TEMPERATURE

PARASITE

POWER

DS18S20 BEGINS

CONVERSION

DEVICE

CONVERTING

TEMPERATURE

MASTER

RX “0s”

MASTER

RX “1s”

MASTER ENABLES

STRONG PUL LUP ON DQ

DS18S 20 CONVERTS

TEMPERATURE

MASTER DISABLES

STRONG PUL LUP

48h

COPY

SCRATCHPAD

PARASITE

POWER

MASTER ENABLES

STRONG PULL-

UP ON DQ

DATA COPIED FROM

SCRATCHPAD TO EEPROM

MASTER DISABLES

STRONG PUL LUP

MASTER

RX “0s”

COPY IN

PROGRESS

MASTER

“1s”

RETURN TO INI TIALIZA TION

SEQUENCE (FIGURE 14) FOR

NEXT TRANSACTION

B4h

READ

POWER SUPPLY

PARASITE

POWERED

MASTER

RX “1s”

MASTER

RX “0s”

MASTER TX TH BYTE

TO SCRATCHPAD

4Eh

WRITE

SCRATCHPAD

MASTER TX TL BYTE

TO SCRATCHPAD

BEh

READ

SCRATCHPAD

HAVE 8 BYTES

BEEN READ

MASTER

TX RESET

MASTER R

DATA BYTE

FROM SCRATCHPAD

MASTER RX SCRATCHPAD

CRC BYTE

MASTER

RX “1s”

B8h

RECALL E2

MASTER BEGINS DATA

RECALL FROM E2 PROM

DEVICE

BUSY RECALLING

DATA

MASTER

RX “0s”

DS18S20

18 of 23

DS18S20 OPERATION EXAMPL E 1

In this example there are multiple DS18S20s on the bus and they are using parasite power. The bus

master initiates a temperature conversion in a specific DS18S20 and then reads its scratchpad and

recalculates the CRC to verify the dat a.

MASTER MO DE

DATA (LSB FIRST )

COMMENTS

Reset

Master i ssues reset pu l se.

Presence

DS18S20s respond with presence pulse.

55h

Master issues Match R OM command.

64-bit ROM code

Master sends DS18S20 ROM code.

44h

Master issues Conver t T comma nd.

DQ line held high by

strong pullup

Master applies str ong pullup to DQ for the duration of the

conver sion (tCONV).

Reset

Master issues r eset pulse.

Presence

DS18S20s respond with presence pulse.

55h

Master issues Match R OM command.

64-bit ROM code

Master sends DS18S20 ROM code.

BEh

Master issues Read Scratchpa d command.

Rx 9 dat a bytes

M ast er reads enti re s c ratc hpad i ncludi ng C RC. The mast er

then recalculates the CRC of the first eight data bytes from the

s c ratchpad a nd com pares th e calculated CRC with the read

CR C (byte 9). If they match, the master continues; if not, the

read o peratio n is repeated.

DS18S20 OPERATION EXAMPL E 2

In this example there is only o ne DS18S20 on the bus and it is us ing paras it e po wer. T he master writ es t o

the TH and TL registers in the DS18S20 scratchpad and then reads the scratchpad and recalculates the

CRC to ver ify t he data. The master t hen co pies t he scratchpad cont ent s to EEPROM.

MASTER MO DE

DATA (LSB FIRST )

COMMENTS

Reset

Master issues r eset pulse.

Presence

DS18S20 re sponds w i th presence p ul se.

CCh

Master issues Skip ROM command.

4Eh

Master issues Write S cra tchpad command.

2 data byt es

M ast er s en ds two data b ytes to s cra tc hpa d (TH and TL)

Reset

Master issues r eset pulse.

Presence

DS18S20 responds with presence pulse.

CCh

Master issues Skip ROM command.

BEh

Master issues Read Scratchpa d command.

Rx 9 dat a bytes

M ast er reads enti re s c ratc hpad i ncludi ng C RC. The mast er

then recalculates the CRC of the first eight data bytes from

the scrat chpad and c ompares the ca lc ulate d CRC with th e

rea d CRC (byte 9 ). If they matc h, the master cont inues ; if not ,

th e read operation i s repeated.

Reset

Master issues r eset pulse.

Presence

DS18S20 responds with presence pulse.

CCh

Master issues Skip ROM command.

48h

Mast er issues Copy S c rat c hpad co m mand.

DQ line held high by

strong pullup

Master applies str ong pullup to DQ for at lea st 10ms while

copy oper ation i s i n progress.

DS18S20

19 of 23

DS18S20 OPERATION EXAMPL E 3

In this example there is only one DS18S20 on the bus and it is using parasite power. The bus master

initiates a temperature conversio n then reads the DS18S20 scratchpad and calculates a higher resolution

resu lt using the dat a from the t emperatur e, COUNT REM AIN and COUNT P E R °C registers.

MASTER MO DE

DATA (LSB FIRST)

COMMENTS

Reset

Master issues r eset pulse.

Presence

DS18S20 responds with presence pulse.

CCh

Master issues Skip ROM command.

44h

Master issues Conver t T comma nd.

DQ line held high by

strong pullup

Master applies str ong pullup to DQ for t he durat i on of th e

conver sion (tCONV).

Reset

Master issues r eset pulse.

Presence

DS18S20 responds with presence pulse.

CCh

Master issues Skip ROM command.

BEh

Master issues Read Scratchpa d command.

Rx 9 dat a bytes

M aster reads e n ti re scratchpad i ncludi ng CR C. The mast er

then recalculates the CRC of the first eight data bytes from the

s c ratchpad a nd com pares th e calculated CRC with the read

CRC (byte 9). If they match, the master continues; if not, the

read o peratio n is repeated. The master al so cal culates the

TE MP_ READ value and st ores th e co ntents of t he COUNT

R EM AI N and COUNT PER °C registers.

Reset

Master issues r eset pulse.

Presence

DS18S20 responds with presence pulse.

— —

CPU calculates extended r esolution temperatur e using the

equation in the Operation—Measuring Temperature section.

DS18S20

20 of 23

ABSOLUTE MAXIMUM RA TINGS

Volta ge Rang e on Any Pin Re lat ive to Ground ........................................................................................ -0.5V to +6. 0V

Continuous Pow e r Dissipation (TA = +70°C)

8-Pin SO (der ate 5.9mW/°C abov e +7 0°C) .......................................................................................... 470.6mW

3-Pin TO-92 (derate 6.3m W/°C abov e +70°C)..................................................................................... 500mW

Operating Temperature Range ................................................................................................................ -55°C to +125°C

Storage Tempe rature Range .................................................................................................................... -55°C to + 125 °C

Lea d T emperature (soldering, 10s) .......................................................................................................... +260°C

Soldering Temperature (reflow)

Lead(Pb)-free ..................................................................................................................................... .+260°C

C ontain i ng l e ad( P b) ............................................................................................................................ +240°C

These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this

specification is not implied. Expos ure to absolute maximum r ating co nditions for extended periods of time may affect reliabil ity.

DC ELECTRICAL CHARACTERISTICS

(VDD = 3.0V to 5.5V, TA = -55°C to +125°C, unless otherwise noted.)

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

NOTES

Supply Voltage

VDD

L o cal Po wer

+3.0

+5.5

Pullup Supply

Voltage VPU

Pa rasite Power

+3.0

+5.5

V 1, 2

L o cal Po wer

+3.0

Thermom eter Error tERR

-10°C to +85°C

±0.5

°C 3

-55°C to +125°C

±2

Input Logic-Low

VIL

-0.3

+0.8

1, 4, 5

Input Logic-High VIH L o cal Po wer +2.2

The lower of

5.5

VDD + 0.3

V 1, 6

Pa rasite Power +3.0

S i nk C urrent

VI/O = 0.4V

4.0

S tandb y Current

IDDS

750

1000

7, 8

Ac tive Curren t

IDD

VDD = 5V

1.5

DQ Input C urrent

µA

Drift

±0.2

°C

NOTES:

1) All voltages a r e refer enc ed to gr ound.

2) The Pul lup Supply Voltage specifica t ion assumes that the pul lup device is ideal, a nd t herefore the high level of

the pullup is equal to VPU. I n ord er to m e et the VIH spec of the DS18S20, the a ctua l supply r a il for t he strong

pullup trans istor mus t inc l ude margi n for th e v oltag e drop ac ross the transist or w hen i t is t urned on; thus:

VPU_ACTUAL = VPU_IDEAL + VTRANSISTOR.

3) S ee typi cal performan ce cur ve in Figure 16.

4) Logic-low voltages a re specified at a sink curr ent of 4mA.

5) To gua ra ntee a presenc e pulse under low voltage pa r a s ite power c onditions, VILMAX may hav e to be reduc ed to

as l ow as 0.5 V.

6) Logic-high volt a ges are specified at a source current of 1mA.

7) S tandb y c urrent s pec ifie d up to +70°C . St andby c urrent typi c all y i s 3 µA at +125°C.

8) To minimize IDDS, DQ should be within the f ollowing ranges: GND ≤ DQ ≤ GND + 0.3V or

VDD – 0.3V ≤ DQ ≤ VDD.

9) Active cur r ent refer s t o supply current during active t emperature conver sions or EEPROM writes.

10) DQ line is high (“high-Z” state).

11) Drift da ta is based on a 1000-hour stress test at +125°C with VDD = 5.5V.

DS18S20

21 of 23

AC ELECTRICAL CHARACTERISTICS—NV MEMORY

(VDD = 3.0V to 5.5V, TA = -55°C to +100°C, unless otherwise noted.)

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

N V Wri te Cy cle Tim e

tWR

EEPROM Writes

NEEWR

-55°C to +55°C

50k

writes

EEPR O M D ata R etention

tEEDR

-55°C to +55°C

years

AC ELECTRICAL CHARACTERISTICS

(VDD = 3.0V to 5.5V; TA = -55°C to +125°C, unless otherw ise noted. )

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

NOTES

Tempera ture C onver si on

Time

tCONV 750 ms 1

Time to Strong P ullu p On tSPON

S ta rt Conv ert T

Command Issued 10 µs

Time Sl ot tSLOT 60 120 µ

Recov ery Tim e tREC 1 µs 1

Writ e 0 L ow T ime

LOW0

120

Writ e 1 L ow T ime tLOW1 1 15 µ

Read Data Valid tRDV 15 µs 1

Reset Tim e Hig h

RSTH

480

µs

Reset Tim e Low

RSTL

480

1, 2

Presence-Det ect H i g h tPDHIGH 15 60 µs 1

Presence-Det ect L o w

PDLOW

240

µs

Capacitance

CIN/OUT

NOTES:

1) See the t iming diagr ams in Figure 17.

2) Under par a site power , if tRSTL > 960µs, a power-on r es et may occur.

Figure 16. Typical Performance Curve

DS18S20 Typical Error Curve

-0.5

-0.4

-0.3

-0.2

-0.1

0.1

0.2

0.3

0.4

0.5

010 20 30 40 50 60 70

Temperature (°C)

Mean Error

+3s Error

-3s Error

DS18S20

22 of 23

Figure 17. Timing Diagrams

PACKAGE INFORMATION

For th e lat est p ack age out l in e in for m ati on and land patt ern s, go to www.maxim-ic.com/packages. Not e tha t a “+” , “#”, or “-”

in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing

pertains to the package regardless of RoHS sta t us.

PACKAGE TYPE PACK AG E CODE OU TLINE NO. LAND PATTERN NO.

8 SO

S8-2

21-0041

90-0096

3 TO-92

(st r aig ht leads)

Q3-1 21-0248 —

3 TO-92

(for med leads)

Q3-4 21-0250 —

DS18S20

REVISION HISTORY

REVISION

DATE

DESCRIPTION

PAGES

CHANGED

042208

I n the Ordering Inf ormation t able, added T O-92 str aig ht-lead packages a nd

included a note that the TO-92 p ackage in tape and reel can be order ed wit h

either for med o r straight lead s 2

8/10

Removed the Top Mark co lumn from t he Ordering I nformation table;

added the continuous po wer diss ipation and lead and solder ing

temperatures to the A bsolute Maximum Ratings section 2, 20

Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.

Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical

Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.