10/97 N/UK 5.10.040.01
Brass Ball Valves
60 Series
Ideally suited for most industrial applications
Easy installation, simple operation and maintenance free
Full bore passage giving minimum flow resistance
Technical Data
Medium:
Compressed air, water, inert gases and any other fluid
compatible with the valve materials
Port Sizes:
G18, G14, G38, G12, G34, G1, G114, G112, G2, G212, G3, G4.
Operating Pressure:
See individual details
Operating Temperature:
Refer to table over the page
Materials
Nickel plated brass body to UNI 5705-65, virgin PTFE seats,
virgin PTFE, Viton or Nitrile seals, chromium plated brass ball,
zinc plated steel handle with PVC grip (plastic handle on mini
ball range).
Ordering Information
To order quote the appropriate product numbers
from the tables on the following pages.
18" – 4" BSP
Standard
Exhausting
3–way
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
Back to Selector Page
Symbol Series Type Application Materials Max Temp Thread
Body Seats & Seals Pressure (bar) Range Standards
6011 Mini General, light duty Brass PTFE & Nitrile “O” ring 10 –10 to +90ºC ISO 228/1
6018 Lockable Exhausting General, with exhaust Brass PTFE 13,6 4-60°C ISO 228/1
6021 Standard General purpose Brass PTFE & Viton “O” ring 45 to 10 –20 to +150ºC ISO 228/1
6021 Three Way General diverting Brass PTFE & Nitrile “O” ring 25 to 16 –15 to +150ºC ISO 228/1
6021 Exhausting
General with exhaust
Brass PTFE 40 to 64 –20 to +100ºC ISO 228/1
6041 Standard Commercial gas and Brass PTFE 55 to 20 –20 to +150ºC ISO 228/1
general
12
1
210
12
1
3
210
12
13
210
12
1
3
210
12
1
210
60 Series Ball Valves
N/UK 5.10.040.02 10/97
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
6011 Series
Miniball
Reduced bore, female/female
A
B
CF
D
E
A
B
CF
D
E
D
A
B
CF
D
E
D
General Information
12
1
210
6011 Series: Light duty in-line brass ball valves suitable for a wide variety of low pressure industrial uses.
6018 Series: Medium duty in-line brass exhausting ball valves. Venting action & lockout design adds safety feature to valve.
6021 Series: Medium duty in-line brass ball valves for most applications. Available as a standard valve, a three way diverting
valve or with a downstream exhaust option.
6041 Series: Special, high quality in-line ball valves with approvals from British Gas, DIN-DVGW, Danish Gas, Svenska
Gasfoereningen. Suitable for gas and water applications as well as more general industrial uses.
Model Thread Max. A B C D E F
size Press.
601112118 G1810 19 20 37 22 5,5 19
601112128 G1410 19 20 37 22 5,5 19
601112138 G3810 19 21 41 24 8,0 21
601112148 G1210 22 25 48 30 10,0 25
Reduced bore, male/female
Model Thread Max. A B C D E F
size Press.
601112218 G1810 19 20 37 22 5,5 19
601112228 G1410 19 20 37 22 5,5 19
601112238 G3810 19 21 41 24 8,0 21
601112248 G1210 22 25 48 30 10,0 25
Reduced bore, male/male
Model Thread Max. A B C D E F
size Press.
601112318 G1810 19 20 48 22 5,5 19
601112328 G1410 19 20 48 22 5,5 19
601112338 G3810 19 21 53 24 8,0 21
601112348 G1210 22 25 62 30 10,0 25
10/97 N/UK 5.10.040.03
60 Series Ball Valves
6021
Standard Ball Valve
Pressure/Temperature diagram
Full bore, female/female
Model Thread Max. A B C E F
size Press.
602112128 G1445 85 36 48 8 23
602112138 G3840 85 36 49 10 24
602112148 G1235 85 40 60 15 30
602112168 G3430 105 47 69 20 38
602112188 G1 25 105 51 83 25 46
6021121A8 G11420 130 63 96 32 58
6021121B8 G11220 130 69 106 40 70
6021121C8 G2 16 165 83 129 50 86
6021121D8 G21216 248 99 159 65 111
6021121E8 G3 10 248 110 182 80 135
6021121F8 G4 10 248 129 219 100 167
Full bore, male/female
Model Thread Max. A B C E F
size Press.
602112228 G1445 85 36 50 8 23
602112238 G3840 85 36 54 10 24
602112248 G1235 85 40 65 15 30
602112268 G3430 105 47 75 20 38
602112288 G1 25 105 51 86 25 46
6021122A8 G11420 130 63 99 32 58
10
20
30
40
50
Bar
–20° +25° +50° +75° +100° +125° +150° °C
1/4
"
3/8
"
1/2
"
3/4
"
1
"
11/4
" -
11/2
"
2
"
3
" - 4"
A
C
F
B
E
A
C
F
B
E
6021
Exhausting Ball Valve
Full bore, female/female
Model Thread Max. A B C D L M
size Press. Thro Bore A/F
602113128EX G1464 100 61 29 8 52 22
602113138EX G3864 100 61 29 10 54 22
602113148EX G1250 100 64 36 15 69 27
602113168EX G3450 120 76 45 20 77 33
602113188EX G1 50 120 80 54 25 89 40
6021131A8EX G11440 150 98 65 32 103 50
A
C
B
D
M (Across Flats)
LExhaust
For T handle valves, substitute 2 for 1 at 4th digit.
For T handle valves, substitute 2 for 1 at 4th digit.
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
60 Series Ball Valves
N/UK 5.10.040.04 10/97
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
6041
Gas Approved Ball Valve
Full bore, female/female
Model Thread Max. A B C E F
size Press.
604112128 G1455 85 41 48 8 23
604112138 G3850 85 41 49 10 24
604112148 G1245 85 44 61 15 32
604112168 G3440 105 53 70 20 40
604112188 G1 35 105 57 84 25 48
6041121A8 G11425 130 70 98 32 60
6041121B8 G11225 130 76 108 40 72
6041121C8 G2 20 165 92 130 50 88
10
20
30
40
50
60
Bar
–20° +25° +50° +75° +100° +125° +150° °C
1/4
"
3/8
"
1/2
"
3/4
"
1
"
11/4
" -
11/2
"
2
"
A
C
F
B
E
6021
3–Way Ball Valve
Full bore, female/female/female
Model Thread Max. A B C E F J
size Press.
602114428 G1425 98 42 52 10 22 26,0
602114438 G3825 98 42 52 10 22 26,0
602114448 G1225 98 45 64 15 27 33,5
602114468 G3416 118 57 74 20 32 39,5
6021144A8 G11410 118 66 100 32 50 54,5
A
F
C
J
B
E
E
E
Test specification differs from standard. Please consult our Technical
Service for futher details.
Pressure/Temperature diagram
For T handle valves, substitute 2 for 1 at 4th digit.
10/97 N/UK 5.10.040.05
60 Series Ball Valves
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
Warning
These products are intended for use in industrial compressed air systems only. Do not use these products where
pressures
and
temperatures
can
exceed those listed under ‘Technical Data’.
Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not
within published specifications, consult Norgren.
Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to
consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or
damage to equipment in the event of such failure.
System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be
adequately provided.
System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products
where applicable.
6018
Lockable Exhausting Ball Valve
Full bore, female/female
Model Thread Max. A B C F G
size Press. Thro Bore A/F
601812128 1413,6 bar 93 45 8 44 20
601812138 3813,6 bar 93 45 9 44 20
601812148 1213,6 bar 93 50 14 58 24
601812168 3413,6 bar 114 57 19 64 30
601812188 1 13,6 bar 114 61 24 81 40
F
7,5
B
C
A
G (Across Flats)
M5 x 0,8 Exhaust Port
Lever lockable only in closed position. Standard handle accepts Ø 7mm
shackle.
Test specification differs from standard. Please consult our Technical
Service for futher details.
11/97 N/UK 5.10.042.01
Carbon Steel Ball Valves
62 Series
Ideally suited for most industrial applications
Easy installation, simple operation and maintenance free
14,38, 12BSP ball valves for high pressure applications
Lever or tee handle options
Technical Data
Medium:
Compressed air, water, inert gases and any other fluid
compatible with the valve materials
Port Sizes:
14, 38, 12, 34, 1 BSPP
Operating Pressure:
140 bar (PTFE seats)
208 bar (Nylon seats)
Operating Temperature:
-30°C to 220°C
Materials:
Body: Steel
Stem: Carbon Steel
Thrust washer: Reinforced PTFE
Stem Seal: Reinforced PTFE
Follower: Stainless steel, type 304
Spring Washer: Zinc plated steel
Handle: Zinc plated steel with vinyl grip
Ball: Chrome plated carbon steel
Seats: Reinforced PTFE or nylon
End Cap: Carbon Steel
Ordering Information
To order quote the appropriate product numbers
from the tables on the following pages.
14" – 1" BSP
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
Back to Selector Page
Model Thread Max Press A B C F
BSPP (bar)
Through Bore
625212128 14140 10 51 25,4 13,5
625212138 38140 10 51 25,4 13,5
625212148 12140 14 63,5 32 16
625212168 34140 17 75 37,5 20,5
625212188 1 140 22 89 44 25,4
62 Series Ball Valves
N/UK 5.10.042.02 11/97
Lever Handle - 625112
D
CB
A
FE
Model Thread Max Press A B C D E F
BSPP (bar)
Through Bore
625112128 14140 10 51 25,4 96 41 13,5
625112138 38140 10 51 25,4 96 41 13,5
625112148 12140 14 63,5 32 96 44 16
625112168 34140 17 75 37,5 129,5 53 20,5
625112188 1 140 22 89 44 129,5 58 25,4
Tee Handle - 625212
CB
A
F
Tee Handle - 626212 (High Pressure)
CB
A
F
Model Thread Max Press A B C F
BSPP (bar)
Through Bore
626212128 14208 10 51 25,4 13,5
626212138 38208 10 51 25,4 13,5
626212148 12208 14 63,5 32 16
General Information
Series Handle Material Max Thread
Seat Pressure (bar) Standards
625112 Lever PTFE 140 ISO 228/1
625212 Tee PTFE 140 ISO 228/1
626212 Tee Nylon 208 ISO 228/1
Warning
These products are intended for use in industrial compressed air systems only. Do not use these products where
pressures
and
temperatures
can
exceed those listed under ‘Technical Data’.
Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not
within published specifications, consult Norgren.
Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider
the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to
equipment in the event of such failure.
System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be
adequately provided.
System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products
where applicable.
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
11/97 N/UK 5.10.041.01
Stainless Steel Ball Valves
61 Series
Ideally suited for most industrial applications
Easy installation, simple operation and maintenance free
Full bore passage giving minimum flow resistance
Suitable for process, chemical or food industries
Lever or tee handle options
Technical Data
Medium:
Compressed air, water, inert gases and any other fluid
compatible with the valve materials
Port Sizes:
14, 38, 12, 34, 1
Operating Pressure:
100 bar (14,38,12), 64 bar (34,1)
Operating Temperature:
-20°C to 150°C
Materials
Body: Stainless Steel Investment casting AISI 316
Stem: Stainless Steel AISI 316
Ball Seats: Virgin PTFE
Lower & upper stem packing: virgin PTFE
Static gasket: Virgin PTFE
Ball: Stainless Steel AISI 316
Viton ‘O’ rings
Lever handle: Stainless Steel AISI 304
End connection: Stainless Steel investment casting AISI 316
Ordering Information
To order quote the appropriate product numbers
from the tables on the following pages.
14" – 1" BSP
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB
Back to Selector Page
Model Thread Max Press A B C D L M
Rp (bar) through A/F
bar
615212128 14100 47 38 29,0 8 50 21,5
615212138 38100 47 38 29,0 10 50 21,5
615212148 12100 47 41 34,0 15 60 26,5
615212168 3464 56 52 42,5 20 70 31,5
615212188 1 64 56 56 50,5 25 85 40,5
61 Series Ball Valves
N/UK 5.10.041.02 11/97
Warning
These products are intended for use in industrial compressed air systems only. Do not use these products where
pressures
and
temperatures
can
exceed those listed under ‘Technical Data’.
Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not
within published specifications, consult Norgren.
Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider
the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to
equipment in the event of such failure.
System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be
adequately provided.
System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products
where applicable.
General Information
Lever Handle - 615112
A
L
D
B
C
Model Thread Max Press A B C D L M
Rp (bar) through A/F
bore
615112128 14100 110 52,0 29,0 8 50 21,5
615112138 38100 110 52,0 29,0 10 50 21,5
615112148 12100 110 55,0 34,0 15 60 26,5
615112168 3464 140 66,0 42,5 20 70 31,5
615112188 1 64 140 70,0 50,5 25 85 40,5
Tee Handle - 615212
Series Handle Thread
Standards
615112 Lever ISO 7/1 Rp
615212 Tee ISO 7/1 Rp
A
L
D
C
B
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.
For your local Norgren Technical Sales Centre phone 0345 662266. For your local Norgren Distributor phone 0345 227777.
IMI Norgren Limited, PO Box 22, Eastern Avenue, Lichfield, Staffordshire WS13 6SB