1209
Related Information
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Static
Removers
Pulse Air-gun
Cleaning Box
Electrostatic
Sensor
EC-G02
Pulse Air-gun Ionizer High-frequency AC Method
EC-G02
Air-gun type ionizer that can remove dust in a single burst
using pulsed ion air
■General terms and conditions ............. F-3 ■Selection guide ........................... P.1155~
■Glossary of terms.......................... P.1591 ■General precautions ..................... P.1595
panasonic.net/id/pidsx/global
The EC-G02 features two pulse air
modes in addition to the standard
continuous mode.
Compact, highly usable
design
A high-voltage power supply
circuit and solenoid valve are built
into the air gun, providing a high
level of usability and eliminating
the need to install an external
controller or route thick, high-
voltage cables.
Additionally, since the lightweight
unit weighs just 270 g, it reduces
stress on the operator, even when
used for extended periods of time.
Pulse air mode
Improved dust removal effectiveness
thanks to pulse (intermittent) air
External input
External input allows the unit to be used in combination
with a foot switch or other device.
No-oil compliance
All parts along the air path (air nozzle, solenoid valve,
joints, etc.) are no-oil compliant.
Since pulse air causes dust to oscillate and lifts it up,
even difcult-to-dislodge dust inside concave pockets
can be easily removed. The EC-G02 can deliver
greater dust removal effectiveness than continuous
airow models.
Pulse air
Three discharge modes
The EC-G02 features a high-
brightness white LED above the
ionized air outlet, allowing you to
target and spray dust revealed by
the light with a stream of ionized
air.
White LED illumination
Pulse Air-gun Ionizer EC-G02
1210
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Static
Removers
Pulse
Air-gun
Cleaning
Box
Electrostatic
Sensor
EC-G02
ORDER GUIDE
Note: Typical value for pulse air mode: CONT at 100 mm 3.937 in from the
front of discharge nozzle at an applied air pressure of 0.50 MPa.
Type Charge removal time
(±1,000 V → ±100 V) Model No.
Gun type 0.5 sec. approx. or less (Note) EC-G02
Designation Model No. Description
Discharge needle EC-GANT For replacement (1 pc.)
Solenoid valve EC-GAV For replacement (1 pc.)
OPTIONS
SPECIFICATIONS
Item
Type Gun type
Model No. EC-G02
CE marking directive compliance
EMC Directive, RoHS Directive
Charge removal time 0.5 sec. approx. or less (±1,000 V → ±100 V) (Note 2)
Applicable uid Air (dried clean air) (Note 3)
Supplied air ow 300 ℓ/min. (ANR) or less
Air pressure range 0.05 to 0.50 MPa
Supply voltage Accessory AC adapter INPUT: 100-240 V AC ±10 % 50/60 Hz
(OUTPUT: 24 V DC)
Power consumption
30 VA or less
Discharge method High-frequency AC method
Pulse air mode Pulse 1 (long) / Pulse 2 (short) / CONT (continuous) selectable by switch
LED illumination mode ON (always ON) / SYNC (synchronized with trigger) / OFF (always OFF)
External input
Ionized air emission operation ON/OFF using OR control with trigger switch
Ionized air emission operation ON: Short-circuited to COM (-)
Ionized air emission operation OFF: Open
Ambient temperature 0 to +50 °C +32 to +122 °F (No dew condensation allowed), AC adapter: 0 to +40 °C +32 to +104 °F
Ambient humidity 35 to 65 % RH (No dew condensation allowed)
Weight 270 g approx. (main unit only)
Accessories
AC adapter: 1pc.
Exclusive intermediate cable (oil-resistant, heat-resistant, bending-resistant type) length 2 m 6.562 ft: 1 pc.
Straight joints
• Tube outer diameter ø8-ø8 mm ø0.315-ø0.315 in compatible type: 1 pc. (Note 4)
• Tube outer diameter ø8-ø6 mm ø0.315-ø0.236 in compatible type: 1 pc.
• Connector connection terminal (Manufactured by Molex): 3 pcs.
Notes: 1) Where measurement conditions have not been specied precisely, the conditions used were an ambient temperature of +20 °C +68 °F.
2) Typical value for pulse air mode: CONT at 100 mm 3.937 in from the front of discharge nozzle at an applied air pressure of 0.50 MPa.
3) Dried clean air is the air passing through air dryer (dew point –20 °C –4 °F approx.) and air lter (mesh size 0.01 μm 0.0004 mil approx.)
4) At the time of shipment from the factory, ø8-ø8 mm ø0.315-ø0.315 in type is attached.
PRECAUTIONS FOR PROPER USE DIMENSIONS (Unit: mm in)
• This product includes precision components,
so do not drop it or hit it against other
objects. If this is not observed, accidents or
problems with operation may occur.
• Never use this product in a device for
personnel protection.
• Do not use this product in places where
there may be danger of ammable or
combustible items being present.
• High voltages are applied to the discharge
needle, so never touch the discharge needle
while the power for the product is turned on,
otherwise electric shocks may result.
• Since the tip of the discharge needle is
sharp, take sufcient care in handling the
discharge needle, or injuries may result.
• If this product is used in an airtight room,
ozone emitted from this product may be
detrimental. Therefore, in order for this
product to be used in an airtight room, be
sure to keep the room ventilated.
• Do not direct ionized air toward the face.
Ozone may cause irritation to places such as
the nose and throat.
• Do not look directly into the white LED
spotlight. It may cause injury to the eyes.
EC-G02 Ionizer main unit
(12.5 0.492)
51
2.026
144 5.670
(4 0.157)
173
6.811
Cable connector (Note)
Straight joint
Trigger
Solenoid valve
indicator
White LED
Mode select
switches
(31 1.220)
(31 1.220)
Nozzle
14
0.551 10
0.394
185
7.283
(
)(
)
( )
( )
8
0.315
Note: An exclusive intermediate cable (oil-resistant, heat-resistant, bending-
resistant type, ø3.7 mm ø0.146 in, 2 m 6.562 ft long) is attached.
The CAD data can be downloaded from our website.Refer to p.1595 for general precautions.