3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series
Physical
Electrical
Environmental
MetPak is a trademark of 3M Company.
* Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. (IEEE).
Insulation
Material: High Temp LCP
Flammability: UL 94V-0
Color: Beige
Contact
Material: Copper Alloy
Plating
Underplating: 50 μ″ (1.27 μm) Nickel
Wiping Area: See Ordering Information
Solder Tails: See Ordering Information
Current Rating: Signal: 1.5 A - All contacts simultaneously
Insulation Resistance: 103 MΩ
Withstanding Voltage: 1000 VAC
Temperature Rating: -55°C to +125°C
Process Temperature Rating: 260°C (Profile per J-STD-020C)
Moisture Sensitivity Level: 1 (per J-STD-020C)
TS-1117-06
Sheet 1 of 4
Date Modified: April 6, 2007
• End-to-end stackable
• Offset dual-beam contact minimizes
insertion force
• Molded guide fingers provide
integrated alignment
• Alignment wafer for true position
• Mates with MP2-P inverse headers
and elevated inverse headers, MP2-PXXXE,
for extended card applications
• Protective Push-Cap on Press-Fit Only
• Meets IEC 61076-4-104 Futurebus+®
global standard
• See Regulatory Information Appendix (RIA)
for chemical compliance information
UL File No: E68080
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series
TS-1117-06
Sheet 2 of 4
Ordering Information
MP2 - SXXXG - 5XXX-C - XXXXX
S = Socket
Contact Count
See Table
Rows
5 = 5 Rows
Contact Arrangement
1 = All positions filled*
Termination Style
M = Solder Tail (Press Peg)
P = Press-Fit (w/Tail Cover)
Tail Length
See Table 2
Guide Finger
*Contact 3M Sales Representative for information on special fill patterns and mono blocked pairs.
Plating Options:
(See Table 3)
C = Capped Solder Tail
Blank = Press-Fit
ROW
C
D
E
POSITION X
B
A
"A"
2
POSITION 1
"B"
2.00
.079
TYP.
5.00
.197 TYP.
ASSEMBLED TO PCB AND MATED WITH MP2-PXXX-5XXX-XXXX
1.50
.059
CENTER LINE OF ROW A
23.30
.917
0.05 ±.05
.002 ±.002
PRESS-FIT AND SOLDER TAIL PRODUCT (CAPPED)
MATED WITH MP2-PXXXE-5XXX-XXXX
23.00
.906
32.97
1.298
22.42
.883
13.50
.532
3.75
.148
13.30
.524
14.50
.571 11.30
.445
"C" TAIL LENGTH
2.00
.079
4X
21.95
.864
23.30
.917
Note:
1. Refer to IEC 61076-4-104 Futurebus+® global standard.
2. "Press Fit" describes a contact tail having a compliant section designed to make a reliable electrical connection
with a plated through-hole (PTH) in a printed circuit board, typically a "back plane.”
0 0.0 0.00
mm ±3 ±0.3 ±0.13
mm
[inch]
Tolerance Unless Noted
[ ] Dimensions for Reference Only
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series
TS-1117-06
Sheet 3 of 4
Plating
Suffix Press-Fit Tails* Solder Tails Plating Composition
0.25 µm [10 µ"] Min. Au Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.76 µm [30 µ"] Min. Au Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.08 µm [3 µ"] Min. Au Contact Area
0.67 µm [27 µ"] Min. PdNi Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated
1.02 µm [40 µ"] Min. PdNi Contact Area
0.10 µm [4 µ"] Min. Pd Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.25 µm [10 µ"] Min. Au Contact Area
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.76 µm [30 µ"] Min. Au Contact Area
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
1.27 µm [50 µ"] Min. Au Contact Area, Lubricated
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.08 µm [3 µ"] Min. Au Contact Area
0.67 µm [27 µ"] Min. PdNi Contact Area
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated
1.02 µm [40 µ"] Min. PdNi Contact Area
0.10 µm [4 µ"] Min. Pd Contact Area
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
*Compliant-Pin Tail
KR
RF
Table 3 - Plating & Regulatory
TG
TG30
TR30
RIA E2 & C2
apply
RIA E3 & C2
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
LR
PD
RIA E2 & C2
apply
RIA E3 & C2
apply
RIA E2 & C2
apply
RIA E3 & C2
apply
RIA E2 & C2
apply
RIA E3 & C2
apply
TR40B
FJ
RIA E1 & C1
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
RIA E1 & C1
apply
Pin
Count Rows
Block
Count
030 11.95 [0.471] 10.00 [0.394] 5 1
060 23.95 [0.943] 22.00 [0.866] 5 2
090 35.95 [1.415] 34.00 [1.339] 5 3
120 47.95 [1.888] 46.00 [1.811] 5 4
150 59.95 [2.361] 58.00 [2.283] 5 5
180 71.95 [2.833] 70.00 [2.756] 5 6
210 83.95 [3.305] 82.00 [3.228] 5 7
240 95.95 [3.778] 94.00 [3.701] 5 8
Table 1 - Connector & Row Lengths
Dim. "A"
mm [inch]
Dim "B"
mm [inch]
Solder Press-Fit*
1 2.72 [0.107]
2 1 3.53 [0.139]
*Compliant-Pin Tail
Table 2 - Tail Length
Contact-to-PC Board Tail
Termination Option No. Dim. "C"
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series
TS-1117-06
Sheet 4 of 4
RECOMMENDED PCB HOLE
MOUNTING PATTERN
lO0.10
lO0.10
lO0.10
A1
"B"
4.00
.157
3.00
.118
1.00
.039
4.00
.157
"D" PLATED THRU HOLE
O2.05 +.05
-.00
.081 +.002
-.000
UNPLATED THRU HOLE
O1.50 +.10
-.00
.059 +.004
-.000
UNPLATED THRU HOLE
THESE HOLES CONSTITUTE MODULAR
REPEATING PATTERN
8.00
.315
2.00
.079
TYP.
2.00
.079
4X
Hole Finished Dia.
mm [in]
Cu Thickness
mm [in]
Immersion Matte Sn
Thickness
microns [µ"]
Electrolitic Au
Thickness
microns [µ"]
OSP ENTEK
Thickness
microns [µ"]
Drilled Hole Dia.
mm [in]
0.700-0.800 0.025-0.045 0.5 - 2.5 0.1 - 0.5 0.2 - 0.5 0.830-0.860 [.0330-.0340] or
[.0276-.0315] [0.001-0.002] [20 - 100] [4 - 20] [8 - 20] 0.85mm [ #66] TWIST DRILL
Table 5 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY
"D"
HOLE Finished Dia.
mm [in]
Cu Thickness mm
[in]
SnPb Thickness
microns [µ"]
Drilled Hole Dia.
mm [in]
"D" 0.65-0.80 [.0256-.0315] 0.025 [.001] min 15 [600] max 0.81-0.86 [.0319-.0339]
Table 4 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY
UNPLATED THROUGH-HOLE
UNPLATED THROUGH-HOLE
“D” PLATED THROUGH-HOLE
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-A
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
20
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO
OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s
option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for
any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
Name and Content of Hazardous Substances or Elements
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
www.3M.com/interconnects RIA-2217-A
© 3M 2007
