DO NOT
SCALE FROM
THIS PRINT
EHF-1XX-01-XX-D-XX-XX-XX
No OF POSITIONS
-03, -04,-05, -08, -10,
-13, -17, -20, -25
ROW SPECIFICATION
-D: DOUBLE
LEAD STYLE
-01
PLATING SPECIFICATION
-L: LIGHT GOLD (USE T-1SXX-XX-L)
-F: FLASH SELECTIVE GOLD
(USE T-1SXX-XX-F)
-S: SELECTIVE (USE T-1SXX-XX-S)
-H: HEAVY GOLD,
GOLD FLASH ON TAIL
(USE T-1SXX-XX-H)
-LM: LIGHT SELECTIVE GOLD,
MATTE TIN ON TAIL
(USE T-1SXX-XX-L)
-SM: HEAVY SELECTIVE GOLD,
MATTE TIN ON TAIL
(USE T-1SXX-XX-S)
-FM: FLASH SELECTIVE GOLD,
MATTE TIN ON TAIL
(USE T-1SXX-XX-F)
OPTION
-LC: LOCKING CLIP (FOR -D-SM ONLY)
(SEE NOTE 7)
-P: PICK & PLACE PAD (FOR -D-SM ONLY)
(FOR -03 & -04, USE PPP-25, SEE FIG 7, SHT 3)
(FOR -05 THRU -25, USE PPP-48, SEE FIG 2)
-K: POLYIMIDE FILM
(USE K-500-300, SEE FIG 3)
-TR: TAPE & REEL PACKAGING
(FOR -D-SM, -D-SM-P, & -D-SM-K ONLY)
(NOT AVAILABLE ON -D-SM-LC)
TAIL OPTION
POLARIZED OPTION
-XX = PIN OMITTED
(N/A ON -RA OPTION)
(LEAVE BLANK FOR THROUGH HOLE,
SEE FIG 4, SHEET 2, USE T-1S63-01-XX)
-SM: SURFACE MOUNT (USE T-1S15-02-XX)
-RA: RIGHT ANGLE
(USE T-1S63-02-XX AND T-1S63-03-XX)
(SEE FIG 5, SHEET 2)
.570 [14.48] REF
(No OF POS x .050 [1.27]) +
.100 2.54
(TYP) REF
.135
REF
3.43
+ .200 [5.08] REF
(No OF POS x.050 [1.27])
.020 0.51
REF
.263 6.67
REF
.05 1.270
.310
REF
7.87
2
MAX SWAY
REF
(No OF POS - 1)
x .050 [1.27]
"A"
"A"
01
02
XX
90°
-
+
.296
±.010
7.52
±0.25
.335 8.51
.004[0.10]
.325 8.26
REF
.060 1.52
.120
REF
3.05
.016
REF
0.41
SECTION "A"-"A"
EHF-XX-D
LC-09-TM
EHF-110-01-XX-D-SM-LC
T-1S15-02-XX
ARM ASSEMBLY & ROTATION
EHA-02
.445 11.31
REF
.180 4.57
-SM IN-PROCESS 1
(SCALE: 1.5:1)
.084 2.13
.296
±.010
7.52
±0.25
90°
±3°
-SM IN-PROCESS 2
(SCALE: 1.5:1)
POS 1 INDICATOR
.200
REF
5.08
.020[0.51]
{(No OF POS X .050[1.27] + .370[9.40]) / 2}
C
L
(SCALE 1.5:1)
.293 7.44
REF
PPP-48
.295
REF
7.50
.020[0.51]
{(NO OF POS X .050[1.27] + .275[6.98]) / 2}
C
L
(SCALE: 1.5:1)
.260 6.60
REF
+ .290 [7.37] REF
(No OF POS x .050 [1.27])
.170
(TYP)
4.318
.083 2.111
C
FIG 1
-P: PICK AND PLACE PAD
FIG 2
FIG 3
-K: POLYIMIDE FILM
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
.050 EJECTOR HEADER ASSEMBLY
BY:
EHF-1XX-01-XX-D-XX-XX-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
ERIC M.
08/17/01
3
1
SHEET SCALE: 1.75:1
INSULATOR: VECTRA E130i, COLOR BLACK
50% REGRIND
TERMINAL: PHOS BRONZE 510 SPRING
F:\DWG\MISC\MKTG\EHF-1XX-01-XX-D-XX-XX-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY TO BE WITHIN .004 [.10].
3. BURR ALLOWANCE: .0015 [.038] MAX.
4. MINIMUM PUSHOUT FORCE: 1 LB MIN.
5. MAXIMUM ALLOWABLE BOW: .002 [.05] INCH/INCH AFTER ASSEMBLY.
6. NOTE DELETED.
7. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC OPTION IS NOT
COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL PLACEMENT
FOR ALL ASSEMBLIES WITH THE –LC OPTION.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION AC
PT-1-24-16-29
PT-1-24-01-51
(LOAD PARTS WITH POSITION #1 INDICATOR
IN SAME DIRECTION AS ARROW ON TUBE)
PACKAGING VIEWS
"B"
"B"
STANDARD THROUGH HOLE
(SHOWN: EHF-110-01-XX-D)
(SAME AS FIG 1, UNLESS OTHERWISE STATED)
FIG 4
.107 2.72
.350 8.89
REF
SECTION "B"-"B"
T-1S63-01-XX
PT-1-24-05-09
PT-1-24-01-52
"C"
"C"
-RA: RIGHT ANGLE OPTION
(SHOWN: EHF-110-01-XX-D-RA)
(SAME AS FIG 1, UNLESS OTHERWISE STATED)
FIG 5
.480 12.19
.120 3.05
T-1S63-03-XX
-RA IN-PROCESS 1
.120 3.05
.580 14.73
.09
REF
2.3
.050 1.27
90°
±3°
T-1S63-02-XX
-RA IN-PROCESS 2
2
MAX SWAY
(TYP)
02
01
.120
REF
3.05
.050 1.27
.050 1.27
.090
REF
2.29
90°
±3°
SECTION "C"-"C"
T-1S63-03-XX
T-1S63-02-XX
C
EJECTOR ARM MUST BE IN UPPRIGHT
POSITION WHEN LOADED INTO TUBES
SHEET OF
.050 EJECTOR HEADER ASSEMBLY
BY:
EHF-1XX-01-XX-D-XX-XX-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
ERIC M.
08/17/01
3
2
SHEET SCALE: 2:1
REVISION AC
F:\DWG\MISC\MKTG\EHF-1XX-01-XX-D-XX-XX-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.400 10.17
REF (TYP)
.097 2.46
REF (TYP)
R
.028 0.70
REF (TYP)
FIG 6
-SM: SURFACE MOUNT OPTION
(SHOWN: EHF-110-01-XX-D-SM-LC)
(SHOWN WITH LATCHES OPEN)
.200 5.08
REF
FIG 7
-03 & -04 PICK AND PLACE PAD
(SHOWN: EHF-104-01-XX-D-SM-XX-P)
PPP-25
.283 7.19
REF
LATCHES OMITTED FOR CLARITY
.526 13.36
REF
FIG 8
EHF MATED WITH FFSD AND ECF
.343 8.70
REF
+.715 [18.16] REF
(NO. OF POSITIONS x .050 [1.27])
APPLICATION VIEW
SHEET OF
.050 EJECTOR HEADER ASSEMBLY
BY:
EHF-1XX-01-XX-D-XX-XX-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
ERIC M.
08/17/01
3
3
SHEET SCALE: 2:1
REVISION AC
F:\DWG\MISC\MKTG\EHF-1XX-01-XX-D-XX-XX-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322