WM8973-EV1M Evaluation Board User Handbook Rev 1.0 WM8973-EV1M TABLE OF CONTENTS TABLE OF CONTENTS .................................................................................. 2 INTRODUCTION ............................................................................................. 4 GETTING STARTED ....................................................................................... 4 EVALUATION BOARD CHECKLIST ...................................................................... 4 CUSTOMER REQUIREMENTS.............................................................................. 4 POWER SUPPLIES ............................................................................................... 5 BOARD FUNCTIONALITY ..................................................................................... 5 BOARD INPUT ....................................................................................................... 6 BOARD OUTPUT ................................................................................................... 6 INTERFACES......................................................................................................... 7 HEADERS .............................................................................................................. 7 LINKS, JUMPERS AND SWITCHES ...................................................................... 9 WM8973 OPERATION .................................................................................. 10 SOFTWARE CONTROL....................................................................................... 10 SERIAL INTERFACE SOFTWARE DESCRIPTION...................................... 12 SOFTWARE DOWNLOAD ................................................................................... 12 SOFTWARE INSTALLATION............................................................................... 12 SOFTWARE OPERATION ................................................................................... 12 DOWER DOWN AND INTERFACE CONTROL ................................................... 16 DAC AND ADC CONTROL................................................................................... 17 VOLUME CONTROL ............................................................................................ 18 MIXER CONTROL................................................................................................ 19 TONE CONTROL ................................................................................................. 20 SCHEMATIC LAYOUT .................................................................................. 21 WM8973-EV1B PCB LAYOUT...................................................................... 29 WM8973-EV1B BILL OF MATERIAL............................................................ 33 APPENDIX .................................................................................................... 35 EXTERNAL DSP CONNECTION TO THE WM8973-EV1B .......................... 35 AUDIO INTERFACE CONNECTIONS.................................................................. 35 SOFTWARE INTERFACE .................................................................................... 37 CONNECTION DIAGRAMS.................................................................................. 37 ADDITIONAL WM8973-EV1B SETUP RECOMMENDATIONS .................... 39 ADC TO DAC LOOPBACK................................................................................... 39 CONNECTION OF AN 8 MONO SPEAKER ...................................................... 40 HEADPHONE AUTO-DETECT FUNCTION ......................................................... 43 w Rev 1.0, February 2005 2 WM8973-EV1M EVALUATION SUPPORT ............................................................................. 44 IMPORTANT NOTICE ................................................................................... 45 ADDRESS: ........................................................................................................... 45 w Rev 1.0, February 2005 3 WM8973-EV1M INTRODUCTION The WM8973 is a stereo CODEC for portable audio applications. This evaluation platform and documentation should be used in conjunction with the latest version of the WM8973 datasheet. The datasheet gives device functionality information as well as timing and data format requirements. This evaluation platform has been designed to allow the user ease of use and give optimum performance in device measurement as well as providing the user with the ability to listen to the excellent audio quality offered by the WM8973. GETTING STARTED EVALUATION BOARD CHECKLIST The following items are available from Wolfson: * WM8973-EV1B Evaluation Board - 6097_QFN32_EV1_REV1 * WM8973-EV1S Control Software (download from http://www.wolfsonmicro.com) * WM8973-EV1M User Handbook (download from http://www.wolfsonmicro.com) CUSTOMER REQUIREMENTS Minimum customer requirements are: * D.C. Power supply of +5V * D.C. Power supply of +1.8V to +3.6V * PC and printer cable (for software control) Minimum PC spec requirements are: * Win95/98/NT/2000/XP * 486 Processor * Approximately 1.5Mb of free hard disk space DAC Signal Path Requires: * Digital coaxial or optical data source * One set of active stereo speakers ADC Signal Path Requires: * Analogue coaxial or 3.5mm jack plug signal source * Digital coaxial or optical data receiving unit Analogue Signal Path Requires: w * Analogue coaxial or 3.5mm jack plug signal source * One set of active stereo speakers Rev 1.0, February 2005 4 WM8973-EV1M POWER SUPPLIES Using appropriate power leads with 4mm connectors, power supplies should be connected as described in Table 1. REF-DES SOCKET NAME J8 +5V SUPPLY +5V J2 DBVDD +1.8V to +3.6V J4 AVDD +1.8V to +3.6V J10 DCVDD +1.42V to +3.6V J47 HPVDD +1.8V to +3.6V J1 DGND 0V J5 AGND 0V Table 1 Power Supply Connections The DGND and AGND connections may be connected to a common GND on the supply with no reduction in performance. To reduce the supply connections that need to be attached to the EVB, sites L1 and L8 are populated with 0R resistors shorting AVDD, HPVDD and DBVDD. In this configuration it is recommended that the supply only be attached to AVDD. If separate supplies are required the 0R resistors should be removed from sites L1 and L8. Note: Refer to WM8973 datasheet for limitations on individual supply voltages. Important: Exceeding the recommended maximum voltage can damage EVB components. Under voltage may cause improper operation of some or all of the EVB components. BOARD FUNCTIONALITY There are three options for inputting digital data into the WM8973 evaluation board. There is a coaxial input (J19) via a standard phono connector or an optical input (U3) via a standard optical receiver module. A direct digital input is also available via one side of a 2x8 pin header (H1). The analogue input signals are applied to the evaluation board via phono connectors J7 (RLINE_IN1), J12 (LLINE_IN1), J14 (RLINE_IN2), J22 (LLINE_IN2), J26 (RLINE_IN3) and J45 (LLINE_IN3). Analogue inputs can also be applied to the evaluation board via 3.5mm jack sockets J9 (MIC_IN1); J16 (MIC_IN2) and J30 (MIC_IN3). There are two options for outputting digital data from the WM8973 evaluation board. There is a coaxial output (J29) via a standard phono connector. The digital signals may also be accessed via one side of a 2x8 pin header (H2). The analogue outputs of the board are via phono connectors J43 (ROUT1), J44 (LOUT1), J41 (LOUT2), J42 (ROUT2), J39 (MONO OUT) and J40 (OUT3). There is also an analogue output via a 3.5mm jack socket J46 (HP_OUT). All WM8973 device pins are accessible for easy measurement via the 2x4 pin headers (J13, J15, J17 and J21) running up each side of the device. Level-shift IC (U4) is used to shift the fixed +5V digital input from the CS8427 (U5) down to the same level as DBVDD and vice-versa. w Rev 1.0, February 2005 5 WM8973-EV1M BOARD INPUT REF-DES SOCKET NAME SIGNAL J19 SPDIF_IN Digital (AES/EBU, UEC958, S/PDIF, EIAJ CP340/1201) signal. U3 OPTICAL_IN Digital (AES/EBU, UEC958, S/PDIF, EIAJ CP340/1201) optical signal. Table 2 Digital Inputs REF-DES SOCKET NAME J7 RLINE_IN1 Analogue signal SIGNAL J12 LLINE_IN1 Analogue signal J14 RLINE_IN2 Analogue signal J22 LLINE_IN2 Analogue signal J26 RLINE_IN3 Analogue signal J45 LLINE_IN3 Analogue signal J9 MIC_IN1 Analogue signal (MIC Input) J16 MIC_IN2 Analogue signal (MIC Input) J30 MIC_IN3 Analogue signal (MIC Input) Analogue signals applied to these connectors are AC coupled before being input to the WM8973. Table 3 Analogue Inputs Note: When used in Master Mode, an SPDIF signal must still be applied to phono connector J19. This input signal is used to allow correct operation of the CS8427 as well as being used to generate the MCLK for the WM8973. BOARD OUTPUT REF-DES J29 SOCKET NAME SPDIF_OUT SIGNAL Digital (AES/EBU, UEC958, S/PDIF, EIAJ CP340/1201) signal. Table 4 Digital Output REF-DES J43 SOCKET NAME ROUT1 SIGNAL Line/Headphone Output J44 LOUT1 Line/Headphone Output J42 ROUT2 Speaker Output J41 LOUT2 Speaker Output J39 MONO OUT J40 OUT3 J46 HP_OUT Mono Output ROUT1/VREF/MONO OUT Headphone Output Table 5 Analogue Outputs w Rev 1.0, February 2005 6 WM8973-EV1M INTERFACES Figure 1 Interfaces HEADERS H1 SIGNAL H2 SIGNAL 1/2 MCLK 12/11 3/4 GND 10/9 ADCDAT 5/6 DACDAT 8/7 GND 7/8 GND 6/5 ADCLRC 9/10 DACLRC 4/3 GND 11/12 GND 2/1 BCLK 13/14 BCLK 15/16 GND J24 SIGNAL 1 ADCLRC_IN 2 GND w J31 GND SIGNAL 1 DACLRC_OUT 2 GND Rev 1.0, February 2005 7 WM8973-EV1M J15 WM8973 PIN NAME J17 WM8973 PIN NAME 1 1 MCLK 1 17 HPVDD 2 2 DCVDD 2 18 AVDD 3 3 DBVDD 3 19 AGND 4 4 DGND 4 20 VREF 5 5 BCLK 5 21 VMID 6 6 DACDAT 6 22 MICBIAS 7 7 DACLRC 7 23 RINPUT3/HPDETECT 8 8 ADCDAT 8 24 LINPUT3 J21 WM8973 PIN NAME J13 WM8973 PIN NAME 1 9 ADCLRC 1 25 RINPUT2 2 10 MONOOUT 2 26 LINPUT2 3 11 OUT3 3 27 RINPUT1 4 12 ROUT1 4 28 LINPUT1 5 13 LOUT1 5 29 MODE 6 14 HPGND 6 30 CSB 7 15 ROUT2 7 31 SDIN 8 16 LOUT2 8 32 SCLK Table 6 Headers w Rev 1.0, February 2005 8 WM8973-EV1M LINKS, JUMPERS AND SWITCHES LINKS AND JUMPERS LINK/JUMPER STATUS DESCRIPTION J18 (BCLK) OPEN SHORT Master mode Slave mode [default setting] J20 (ADCLRC) OPEN SHORT Master mode Slave mode [default setting] J25 (DACLRC) OPEN SHORT Master mode Slave mode [default setting] J23 OPEN SHORT Master mode Slave mode (Ties ADCLRC to DACLRC) [default setting] J32, J33, J34 and J35 OPEN SHORT OUT signals are AC coupled [default setting] OUT signals are not AC coupled J37 (external speaker connection) Pin 1 - AGND Pin 2 - +ve speaker connection J38 (external speaker connection) Pin 1 - AGND Pin 2 - -ve speaker connection J6 (DC input connection) Pin 1 - DC signal input Pin 2 - AGND J11 (DC input connection) Pin 1 - DC signal input Pin 2 - AGND Table 7 Links SWITCHES SWITCH STATUS SW6 DESCRIPTION After an input data format change has been made using SW3, the CS8427 will only latch the new settings after SW6 has been pressed and released. SW3 (DATA FORMAT) 1 1 1 1 2 0 0 0 3 0 0 0 4 1 0 0 5 0 0 0 6 0 1 0 DATA FORMAT I2S Compatible [default setting] 24-bit Right Justified Left Justified SW4 (Software Control) Pins 1 and 2 SHORT Pins 2 and 3 SHORT 3-wire (SPI) Control Mode [default setting] 2-wire Control Mode SW1, SW2 (R/Line Input 1 Select) Pins 1 and 2 SHORT Pins 2 and 3 SHORT MIC Input Select (3.5mm Jack Socket) Line Input Select (Phono Socket) [default setting] SW5, SW7 (R/Line Input 2 Select) Pins 1 and 2 SHORT Pins 2 and 3 SHORT MIC Input Select (3.5mm Jack Socket) Line Input Select (Phono Socket) [default setting] SW8, SW9 (R/Line Input 3 Select) Pins 1 and 2 SHORT Pins 2 and 3 SHORT MIC Input Select (3.5mm Jack Socket) Line Input Select (Phono Socket) [default setting] SW27, SW28 (R/LOUT 1 Select) Pins 1 and 2 SHORT Pins 2 and 3 SHORT HP Output Select (3.5mm Jack Socket) Line Output Select (Phono Socket) [default setting] SW36 Pins 1 and 2 SHORT Pins 2 and 3 SHORT Connects to OUT3 for HP output DC reference Connects to GND for HP output reference [default setting] Table 8 Switches w Rev 1.0, February 2005 9 WM8973-EV1M WM8973 OPERATION SOFTWARE CONTROL There are two possible serial software control modes that may be selected to operate the WM8973. The standard SPI user interface is a 3-wire solution with the second option being a 2-wire solution. 3-WIRE MODE To operate the WM8973 in SPI (3-wire) mode, jumper switch SW4 must be set so that pins 1 and 2 are SHORT. The 3-wire serial interface then becomes active on pins 30(CSB), 31(SDIN) and 32(SCLK). The serial interface on the board can be connected to a PC via the printer port or any other standard parallel port. The port used can be selected through the software provided. The software supplied with this kit gives the user access to all the possible features provided by the WM8973. The 3-wire latch, data and clock lines may also be connected to the board via the test points TP2 (CSB), TP4 (SDIN) and TP3 (SCLK). Please refer to the WM8973 datasheet for full details of the serial interface timing and all register features. CSB SCLK SDIN B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Figure 2 3-Wire Serial Interface 2-WIRE MODE To operate the WM8973 in 2-wire mode, jumper switch SW4 must be set so that pins 2 and 3 are SHORT. The 2-wire serial interface becomes active on pins 31(SDIN) and 32(SCLK). The serial interface on the board can be connected to a PC via the printer port or any other standard parallel port. Note: a bi-directional parallel port is required for 2-wire operation1. The 2-wire data and clock lines may also be connected to the board via the test points TP4 (SDIN) and TP3 (SCLK). When used in 2-wire mode, the WM8973 has two possible addresses (0011010 [0x34h] or 0011011 [0x36h]) that are selectable by pulling CSB low or high. If connecting a probe to the Test Points it must be noted that the CSB line is pulled high on the WM8973 evaluation board selecting address 0011011. CSB must be pulled low or driven low through the software writes if address 0011010 is used (as is done in the WM8973-EV1S software provided). R ADDR SDIN R/W ACK DATA B15-8 ACK DATA B7-0 ACK SCLK START STOP Figure 3 2-Wire Serial Interface Note: 1If the 2-wire mode does not operate as expected, the likely cause is the configuration of the parallel port interface mode. Check that the port is configured for bi-directional communication. Most PCs allow the parallel port to be configured in the BIOS settings during initial PC power up. w Rev 1.0, February 2005 10 WM8973-EV1M ADDRESS remarks REGISTER Bit[8] Bit[7] Bit[6] Bit[5] Bit[4] Bit[3] Bit[2] Bit[1] Bit[0] default (Bit 15 - 9) R0 (00h) 0000000 Left Input volume LIVU LINMUTE LIZC LINVOL 010010111 R1 (01h) 0000001 Right Input volume RIVU RINMUTE RIZC RINVOL 010010111 R2 (02h) 0000010 LOUT1 volume LO1VU LO1ZC LOUT1VOL[6:0] 001111001 R3 (03h) 0000011 ROUT1 volume RO1VU RO1ZC ROUT1VOL[6:0] 001111001 R4 (04h) 0000100 Reserved 0 0 R5 (05h) 0000101 ADC & DAC Control R6 (06h) 0000110 Reserved 0 0 0 R7 (07h) 0000111 Audio Interface 0 BCLKINV MS R8 (08h) 0001000 Sample rate R9 (09h) 0001001 Reserved 0 R10 (0Ah) 0001010 Left DAC volume LDVU 0 ADCDIV2 DACDIV2 BCM[1:0] 0 0 0 HPOR DACMU 0 0 0 LRSWAP LRP ADCPOL[1:0] 0 0 0 000000000 ADCHPD 000001000 0 000000000 0 WL[1:0] CLKDIV2 0 0 DEEMPH[1:0] FORMAT[1:0] 000001010 USB 000000000 0 000000000 SR[4:0] 0 0 0 0 0 0 LDACVOL[7:0] 011111111 R11 (0Bh) 0001011 Right DAC volume RDVU R12 (0Ch) 0001100 Bass control 0 BB BC 0 RDACVOL[7:0] 0 BASS[3:0] 011111111 000001111 R13 (0Dh) 0001101 Treble control 0 0 TC 0 0 TRBL[3:0] 000001111 0 MODE3D R15 (0Fh) 0001111 Reset R16 (10h) 0010000 3D control writing to this register resets all registers to their default state R17 (11h) 0010001 ALC1 ALCSEL[1:0] R18 (12h) 0010010 ALC2 0 R19 (13h) 0010011 ALC3 0 R20 (14h) 0010100 Noise Gate 0 R21 (15h) 0010101 Left ADC volume LAVU LADCVOL[7:0] 011000011 R22 (16h) 0010110 Right ADC volume RAVU RADCVOL[7:0] 011000011 R23 (17h) 0010111 Additional control(1) TSDEN R24 (18h) 0011000 Additional control(2) OUT3SW[1:0] R25 (19h) 0011001 Pwr Mgmt (1) VMIDSEL[1:0] DACL ALCZC 3DUC 3DLC MAXGAIN[2:0] 0 0 0 DCY[3:0] DACR 3DEN 000000000 ALCL[3:0] 001111011 HLD[3:0] 000000000 ATK[3:0] NGTH[4:0] VSEL[1:0] not reset 3DDEPTH[3:0] 000110010 NGG[1:0] DMONOMIX[1:0] HPSWEN HPSWPOL ROUT2INV NGAT 000000000 DATSEL[1:0] DACINV TOEN 011000000 TRI LRCM ADCOSR DACOSR 000000000 DIGENB 000000000 VREF AINL AINR ADCL ADCR MICB LOUT1 ROUT1 LOUT2 ROUT2 MONO OUT3 0 000000000 VROI 0 0 0 0 0 0 000000000 RDCM R26 (1Ah) 0011010 Pwr Mgmt (2) R27 (1Bh) 0011011 Additional Control (3) R31 (1Fh) 0011111 ADC input mode DS MONOMIX[1:0] R32 (20h) 0100000 ADCL signal path 0 LINSEL[1:0] R33 (21h) 0100001 ADCR signal path 0 R34 (22h) 0100010 Left out Mix (1) LD2LO LI2LO LI2LOVOL[2:0] 0 R35 (23h) 0100011 Left out Mix (2) RD2LO RI2LO RI2LOVOL[2:0] 0 R36 (24h) 0100100 Right out Mix (1) LD2RO LI2RO LI2ROVOL[2:0] 0 R37 (25h) 0100101 Right out Mix (2) RD2RO RI2RO RI2ROVOL[2:0] 0 0 R38 (26h) 0100110 Mono out Mix (1) LD2MO LI2MO LI2MOVOL[2:0] 0 R39 (27h) 0100111 Mono out Mix (2) RD2MO RI2MO RI2MOVOL[2:0] 0 R40 (28h) 0101000 LOUT2 volume LO2VU LO2ZC LOUT2VOL[6:0] 001111001 R41 (29h) 0101001 ROUT2 volume RO2VU RO2ZC ROUT2VOL[6:0] 001111001 R42 (2Ah) 0101010 MONOOUT volume 0 MOZC MOUTVOL[6:0] 001111001 ADCLRM[1:0] RINSEL[1:0] LDCM 0 0 0 0 000000000 LMICBOOST[1:0] 0 0 0 0 000000000 RMICBOOST[1:0] 0 0 0 0 000000000 LMIXSEL[2:0] 0 0 001010000 0 001010000 0 0 001010000 0 0 0 001010000 0 0 0 001010000 RMIXSEL[2:0] 001010000 Table 9 Mapping of Program Registers Please refer to the WM8973 datasheet for full details of the serial interface timing and all register features. w Rev 1.0, February 2005 11 WM8973-EV1M SERIAL INTERFACE SOFTWARE DESCRIPTION The following section will detail the downloading and installation of evaluation software and also the operation of the software and the functionality of each control button. SOFTWARE DOWNLOAD The current evaluation board control software WM8973-EV1S should be downloaded from the Wolfson website [www.wolfsonmicro.com]. From the homepage it is recommended to carry out a search for `WM8973' and select the evaluation board 'more' button. Select `download' from the top right hand corner under the software label. Once the licence agreement has been accepted, select the WM8973_EV1S_REVx.x.ZIP link and download to your hard drive. SOFTWARE INSTALLATION Once the .zip file has been downloaded, to install the software: * Open the .zip file. * Double click on the setup.exe file. * Follow the on-screen installation instructions and save to the desired location. The software can then be opened by either running the extracted WM8973_EV1_REVx.x.exe file from the saved location or alternatively, selecting: Start > Programs > WM8973-EV1SREVx.x > WM8973-EV1S. SOFTWARE OPERATION Due to the many features offered by the WM8973, the software has been split into five different panels. This eases the complexity of the software making each panel less busy, the panels have also been grouped so that it makes it simple to control each section of the device. The main menu panel shown in Figure 4 is used to call up the other panels as well as offering a number of pull-down menus. Figure 4 Software Menu Panel w Rev 1.0, February 2005 12 WM8973-EV1M The `Submit All' button will submit values to every register of the WM8973. The `Reset' button writes to the reset register (R15) but does not reset the control panel values. If the previous values are to be resubmitted then the `Submit All' button should be pressed, if the user would like to start afresh then the `Reset Software Panel Settings' button should also be pressed. Pressing this button does not write to the device, it only resets the panel settings to their default state. Left clicking on the Wolfson logo will open the PCs default web browser and go to the Wolfson Microelectronics website (`www.wolfsonmicro.com'). The DAC, ADC and Line setup buttons have also been provided as a quick start approach. Pressing either of these buttons will power up the DAC, ADC or Line signal paths in a known state as described in the following pages. Important: The CS8427 SPDIF decoder IC will only work at a rate of 256fs. This will limit the sample rates that may be set using the WM8973 unless an external source is used to supply signals directly to the relevant pins of header H1 or taking the signals from the relevant pins of header H2. DAC SUBMIT SETUP By pressing the `DAC Setup' button, the software writes to the device setting the following path: SPDIF_In through the DAC to the L/ROUT1 and L/ROUT2 outputs. The default format setting is 24-bit, I2S. Table 6 lists the required board settings to allow this signal path to be used. This button is intended to ease the initial use of the WM8973 until the user becomes familiar with both device and software operation. Figure 5 Recommended DAC Setup w Rev 1.0, February 2005 13 WM8973-EV1M LINKS AND JUMPERS LINK/JUMPER STATUS DESCRIPTION H1 All jumpers in place DAC clocks and data input H2 No jumpers in place ADC clocks and data output SW36 Pins 2 and 3 SHORT Connects to GND for HP output reference J18 (BCLK) SHORT Slave mode J20 (ADCLRC) SHORT Slave mode J25 (DACLRC) SHORT Slave mode J23 SHORT Slave mode J32, J33, J34 and J35 OPEN OUT signals are AC coupled SW3 1 1 2 0 3 0 4 1 5 0 6 0 DATA FORMAT I2S Compatible SW4 Pins 1 and 2 SHORT 3-wire (SPI) Control Mode SW1, SW2 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW5, SW7 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW8, SW9 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW27, SW28 Pins 2 and 3 SHORT Line Output Select (Phono Socket) Table 10 DAC Setup Jumper Settings (Slave Mode) ADC SUBMIT SETUP By pressing the `ADC Setup' button, the software writes to the device setting the L/RLINE_IN1 through ADC to SPDIF_Out path active. As with the DAC setup described previously, this is to ease the initial use of the WM8973 until the user becomes familiar with both device and software operation. It should be noted that the SPDIF_In connection is still required to provide the necessary clocks to the WM8973 in this mode. Figure 6 Recommended ADC Setup w Rev 1.0, February 2005 14 WM8973-EV1M LINKS AND JUMPERS LINK/JUMPER STATUS DESCRIPTION H1 All jumpers in place except for the jumper connecting pins 5 and 6 and 7 and 8. DAC clocks and data input H2 All jumpers in place ADC clocks and data output SW36 Pins 2 and 3 SHORT Connects to GND for HP output reference J18 (BCLK) SHORT Slave mode J20 (ADCLRC) SHORT Slave mode J25 (DACLRC) SHORT Slave mode J23 SHORT Slave mode J32, J33, J34 and J35 OPEN OUT signals are AC coupled SW3 1 1 2 0 3 0 4 1 5 0 6 0 DATA FORMAT I2S Compatible SW4 Pins 1 and 2 SHORT 3-wire (SPI) Control Mode SW1, SW2 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW5, SW7 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW8, SW9 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW27, SW28 Pins 2 and 3 SHORT Line Output Select (Phono Socket) Table 11 ADC Setup Jumper Setup (Slave Mode) LINE SUBMIT SETUP By pressing the `Line Setup' button, the software writes to the device setting the L/RLINE_IN1 through the analogue path to the L/ROUT1 and L/ROUT2 outputs. As with the setups previously described, this is to ease the initial use of the WM8973 until the user becomes familiar with both device and software operation. DGND DBVDD +1.8V to +3.6V J1 J2 AVDD +1.8V to +3.6V AGND J4 J5 PARALLEL PORT +5V J8 J6 DCVDD +1.42V to +3.6V OPEN SW3 1 2 3 4 5 J10 RLINE IN1 SW1 0 1 6 SW4 SW2 LLINE IN1 J11 H1 J13 SW6 RLINE IN2 J17 J15 SW5 J18 OPT _IN SW7 J20 J24 SPDIF_ IN LLINE IN2 J23 J21 J25 H2 RLINE IN3 1 1 SW9 1 LLINE IN3 1 J38 J37 1 SW36 1 J31 J33 J32 J35 J34 SW8 SW28 SW27 1 SPDIF_ OUT 1 J47 HPVDD +1.8V to +3.6V Figure 7 Recommended Line Setup w Rev 1.0, February 2005 15 WM8973-EV1M LINKS AND JUMPERS LINK/JUMPER STATUS DESCRIPTION H1 No jumpers in place DAC clocks and data input H2 No jumpers in place ADC clocks and data output SW36 Pins 2 and 3 SHORT Connects to GND for HP output reference J18 (BCLK) SHORT Slave mode J20 (ADCLRC) SHORT Slave mode J25 (DACLRC) SHORT Slave mode J23 SHORT Slave mode J32, J33, J34 and J35 OPEN OUT signals are AC coupled SW3 1 1 2 0 3 0 4 1 5 0 6 0 DATA FORMAT I2S Compatible SW4 Pins 1 and 2 SHORT 3-wire (SPI) Control Mode SW1, SW2 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW5, SW7 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW8, SW9 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW27, SW28 Pins 2 and 3 SHORT Line Output Select (Phono Socket) Table 12 Line Setup Jumper Setup (Slave Mode) DOWER DOWN AND INTERFACE CONTROL Figure 8 Power and Interface Control The Power Down and Interface Control panel is used to enable/disable the various sections of the WM8973. It is also used to set the audio interface to the required data format. Pressing the `Power Submit' button will cause the settings shown on this panel to be written to the WM8973. A full device register write is not sent. w Rev 1.0, February 2005 16 WM8973-EV1M DAC AND ADC CONTROL Figure 9 DAC and ADC Control The DAC and ADC Control panel is used to control the many DAC and ADC related features of the WM8973. Pressing the `ADC and DAC Submit' button will cause the settings shown on this panel to be written to the WM8973. A full device register write is not sent. w Rev 1.0, February 2005 17 WM8973-EV1M VOLUME CONTROL Figure 10 Volume Control The Volume Control panel is used to control both analogue and digital volume settings of the WM8973. The volume sliders update in `real' time (i.e. the `Volume Submit' button does not have to be pressed to update the output volume level) but will only have an effect on the output if the Volume Update bits are set. Once changes are made to the Volume Update bits, the `Volume Submit' button must be left clicked for the change to take effect. Pressing the `Volume Submit' button will cause the settings shown on this panel to be written to the WM8973. A full device register write is not sent. w Rev 1.0, February 2005 18 WM8973-EV1M MIXER CONTROL Figure 11 Mixer Control The Mixer Control panel is used to control the many signal mixing options offered by the WM8973. The volume sliders update in `real' time (i.e. the `Mixer Submit' button does not have to be pressed to update the mixer volume level). Pressing the `Mixer Submit' button will cause the settings shown on this panel to be written to the WM8973. A full device register write is not sent. w Rev 1.0, February 2005 19 WM8973-EV1M TONE CONTROL Figure 12 Tone Control The Tone Control panel is used to control the various tone options (3D, Bass, Treble, etc) offered by the WM8973. The sliders update in `real' time (i.e. the `Tone Submit' button does not have to be pressed to update the relevant tone slider level). Pressing the `Tone Submit' button will cause the settings shown on this panel to be written to the WM8973. A full device register write is not sent. It is important to note that to change the `3D Select' control setting from Record to Playback, the ADC and DAC must be set to a power down state in the Power Down and Interface Control panel. After the `3D Select' setting has been made and written to the WM8973 the ADC and DAC should be powered up. Once any of the WM8973 default settings are changed on the control panel, the relevant section is highlighted in blue to show the section where the setting has changed. The highlight around the relevant section also has the purpose of letting the user know that they have not yet submitted the required changes to the WM8973. After a Submit from the relevant panel or a main panel Submit, the sections will default back to their original 'panel grey' colour. The Submit button also becomes inactive until another change is made to the register settings. Refer to the Appendix Section of this user manual for additional evaluation board setup details. w Rev 1.0, February 2005 20 WM8973-EV1M SCHEMATIC LAYOUT Figure 13 Functional Diagram w Rev 1.0, February 2005 21 WM8973-EV1M Figure 14 Digital Input w Rev 1.0, February 2005 22 WM8973-EV1M Figure 15 Software Control w Rev 1.0, February 2005 23 WM8973-EV1M Figure 16 Level Shift w Rev 1.0, February 2005 24 WM8973-EV1M Figure 17 Analogue Input w Rev 1.0, February 2005 25 WM8973-EV1M Figure 18 WM8973 w Rev 1.0, February 2005 26 WM8973-EV1M Figure 19 Analogue Output w Rev 1.0, February 2005 27 WM8973-EV1M Figure 20 Power w Rev 1.0, February 2005 28 WM8973-EV1M WM8973-EV1B PCB LAYOUT Figure 21 Top Layer Silkscreen w Rev 1.0, February 2005 29 WM8973-EV1M Figure 22 Top Layer w Rev 1.0, February 2005 30 WM8973-EV1M Figure 23 Bottom Layer w Rev 1.0, February 2005 31 WM8973-EV1M Figure 24 Bottom Layer Silkscreen w Rev 1.0, February 2005 32 WM8973-EV1M WM8973-EV1B BILL OF MATERIAL REFERENCE DESCRIPTION QUANTITY 74ALVC164245 16 Bit Dual Supply Bus Transceiver SSO U4 1 10uF 6.3 Dia 2.5 pitch Oscon Through Hole Cap. 16V 20% C5-6 C9 C18 C21 C23 C27 C29 C38 C41 C48-49 C70-71 C78 15 1uF 4 Dia 2 pitch Oscon Through Hole Cap. 25V 20% C35 C57 2 220uF 10 Dia 5 pitch Oscon Through Hole Cap. 10V 20% C65-66 2 0.01uF 0805 SMD Ceramic Capacitor 50V X7R C46 C2-3 C8 C14-16 C20 C26 C30-33 C37 C40 C43 C45 C51 C53-54 C56 C58-60 C68 C80 1 0.1uF 0805 SMD Ceramic Capacitor 50V X7R 25 1nF 0805 SMD Ceramic Capacitor 50V NPO C47 C55 2 1uF 0805 SMD Ceramic Capacitor 10V X7R C4 C17 C24 C39 C64 C72-75 C79 10 220pF 0805 SMD Ceramic Capacitor 50V X7R C1 C7 C13 C19 C22 C25 C34 C50 C63 C67 C69 C76-77 C81-87 20 Unpop 0805 SMD Ceramic Capacitor site C10-12 C28 C36 C42 C44 C52 C62 9 4.7nF 1206 SMD Ceramic Capacitor 50V COG C61 1 3.5mm Jack Socket 6.5mm Centre Height J9 J16 J30 J46 4 2x4 2.54mm pitch PCB Pin Header VERTICAL J13 J15 J17 J21 4 2x6 2.54mm pitch PCB Pin Header VERTICAL H2 1 2x8 2.54mm pitch PCB Pin Header VERTICAL H1 1 36-way Centronics/IEE488 PCB mountable Connector J3 SW1-2 SW4-5 SW7-9 SW27-28 SW36 1 JSK9-16-G0 PCB 1x3 Jumper Switch 0.1" Center-off VERTICAL 10 4mm Non-Insulated Panel Socket 16A J1-2 J4-5 J8 J10 J47 7 Phono Socket PCB mount BLACK J29 J39-40 3 Phono Socket PCB mount RED J7 J14 J26 J42-43 5 Phono Socket PCB mount WHITE J12 J22 J41 J44-45 5 Phono Socket PCB mount YELLOW J19 1 Unpop SMB Connector PCB Mount J48 1 CS8427 96KHz Audio Transceiver U5 1 DS1813 5V active Low Power-On-Reset chip SOT U2 1 0R 1206 Resistor on 1210 Inductor site L1-5 L8 L10 7 3.3uH 1210 Surface Mount Inductor '1210A series' L7 1 47uH 1210 Surface Mount Inductor 'PA series' L6 1 Unpop 1210 Surface Mount Inductor site L9 1 HSMY-C670 0805 SMD Chip LED YELLOW D1 J6 J11 J18 J20 J23-25 J31-35 J3738 1x2 PCB Pin Header 0.1" VERTICAL 1 14 Slotted Panhead Screw - M3 thread; 12mm long SC1-4 Hexagonal brass M3 size spacer 20mm length P1-4 4 Plain M3 size washer W1-4 R4 R6 R8 R21 R60-62 R75 R78 R80 R82 4 0R 0805 SMD chip resistor 1% 0.1W 4 11 100K 0805 SMD chip resistor 1% 0.1W R43 1 100R 0805 SMD chip resistor 1% 0.1W R58-59 R63-64 R71-72 6 10K 0805 SMD chip resistor 1% 0.1W R48 R56-57 R65-66 5 1K2 0805 SMD chip resistor 1% 0.1W R5 R7 R9 R47 4 330R 0805 SMD chip resistor 1% 0.1W R15 1 47K 0805 SMD chip resistor 1% 0.1W R10 R18 R22-32 R36 R52 R67-70 19 4K7 0805 SMD chip resistor 1% 0.1W R11-13 R1 R3 R16-17 R20 R35 R40-41 R46 R51 R73-74 3 5K6 0805 SMD chip resistor 1% 0.1W w 12 Rev 1.0, February 2005 33 WM8973-EV1M REFERENCE DESCRIPTION QUANTITY 620R 0805 SMD chip resistor 1% 0.1W R55 1 680R 0805 SMD chip resistor 1% 0.1W R33 1 75R 0805 SMD chip resistor 1% 0.125W R42 1 Unpopulated 0805 resistor site R2 R14 R19 R34 R37-39 R44-45 R49-50 R53-54 R76-77 R79 R81 17 DIL Switch 6-Way Rocker SW3 1 B3F1000 SPNO PCB mount switch SW6 1 1.32mm PCB Test Terminal BLACK TP1 TP5-9 6 1.32mm PCB Test Terminal RED TP2-4 3 Unpop 1.32mm PCB Test Terminal TP10 1 TORX176 Digirtal Audio Optical Receiver U3 1 2:1 Ratio 96KHz SPDIF Digital Audio transformer SOIC(1) U6 1 TN0200T N- Channel MOSFET SOT23 Q1-3 3 WM8973L Stereo CODEC for Portable Audio QFN U1 1 Table 13 WM8973-EV1M Bill of Materials Note: 1 The audio transformer used on this board is manufactured by Scientific Conversion Inc. (www.scientificonversion.com). w Rev 1.0, February 2005 34 WM8973-EV1M APPENDIX EXTERNAL DSP CONNECTION TO THE WM8973-EV1B The WM8973-EV1B evaluation board has been designed to allow it to be easily connected to an external DSP platform with error free operation. The following information is provided to ease the connection process and ensure that all signals sent and received by the WM8973-EV1B are reliable and at the correct voltage levels. AUDIO INTERFACE CONNECTIONS It is recommended that twisted pair (signal twisted with GND) or shielded wires are used to make the audio interface connections between the DSP and WM8973-EV1B platforms. This is to ensure that no interference or noise is picked up by the clocks or data lines, thus reducing performance and reliability. When the WM8973 is set in Slave Mode, the jumpers on header H1 should be removed, disconnecting the digital input section of the evaluation board. The audio interface timing and data signals from the DSP platform should then be connected as shown in Figure 25. The signals should be connected to H1 and not to the header strips J15 and J21 running up each side of the device. Connecting the signals to the output side of the level-shift IC (U4) will cause drive contention between U4 and the DSP and could result in damage to either or both devices. In most cases, the DSP supplies will be set around 3V for low power portable applications. The inputs to the level-shift IC (74ALVC164245) have a TTL threshold (i.e. Logic High = +2V(min); Logic Low = +0.8V(max)) and low input current requirements (i.e. 15uA max) allowing most DSPs to connect directly. MCLK GND DACDAT GND DACLRC GND BCLK GND H1 Figure 25 Connections from DSP Platform The digital inputs to the WM8973 have a CMOS threshold (i.e. Logic High (min) = DBVDDx0.7; Logic Low (max) = DBVDDx0.3). These are met directly by the level shift IC outputs. The jumpers on H2 should also be removed, disconnecting the digital output section of the WM8973 evaluation board. The ADCDAT data from the WM8973 should then be connected to the DSP via pin 8 of header strip J15 and the GND connection should be taken from pin 4 of header strip J15. The ADCDAT signal should be taken direct from the WM8973 digital output as the output side of the level-shift IC (U4) from the WM8973 is pulled up to +5V which may overdrive and cause damage to the DSP inputs. The digital output levels of the WM8973 are Logic High (min) = DBVDDx0.9; Logic Low (max) = DBVDDx0.1 which should meet the input level requirements of most DSPs running at +3V supplies. If the DSP is running with +5V supplies then the connections to it should be made from the output side of the level-shift IC (U4), connecting the signals as shown in Figure 26. w Rev 1.0, February 2005 35 WM8973-EV1M GND ADCDAT H2 Figure 26 Data Connection to the DSP Platform (+5V tolerant input levels) When the WM8973 is set to Master Mode, the jumpers on header H1 should be removed, disconnecting the digital input section of the evaluation board. If an external MCLK signal is being used (i.e. supplied by the DSP) then the DSP platform should be connected as shown in Figure 27. The signal should be connected to H1 and not to the header strip J15 running up the side of the device. Connecting the signal to the output side of the level-shift IC (U4) will cause drive contention between U4 and the DSP and could result in damage to either or both devices. In most cases, the DSP supplies will be set around +3V for low power portable applications. The inputs to the level-shift IC (74ALVC164245) have a TTL threshold (i.e. Logic High = +2V(min); Logic Low = +0.8V(max)) and low input current requirements (i.e. 15uA max) allowing most DSPs to connect directly. MCLK GND H1 Figure 27 Timing Connections from DSP Platform The digital inputs to the WM8973 have a CMOS threshold (i.e. Logic High (min) = DBVDDx0.7; Logic Low (max) = DBVDDx0.3). These are met directly by the level shift IC outputs. The jumpers on H2 should also be removed, disconnecting the digital output section of the WM8973 evaluation board. The ADCDAT, BCLK and ADCLRC signals from the WM8973 should then be connected to the DSP from headers J15 and J21 running up each side of the WM8973. The ADCDAT, BCLK and ADCLRC signals should be taken direct from the WM8973 digital output as the output side of the level-shift IC (U4) from the WM8973 is pulled up to +5V which may overdrive and cause damage to the DSP inputs. The digital output levels of the WM8973 are Logic High (min) = DBVDDx0.9; Logic Low (max) = DBVDDx0.1 which should meet the input level requirements of most DSPs running at +3V supplies. If the DSP is running with +5V supplies (and +5V tolerant inputs) then the connections from the WM8973 evaluation board to the DSP should be made from H2 on the output side of the level-shift IC from the WM8973 as shown in Figure 28. GND ADCDAT GND ADCLRC GND BCLK H2 Figure 28 Connections to the DSP Platform (+5V tolerant input levels) This will ensure that the DSP input level specifications are met. w Rev 1.0, February 2005 36 WM8973-EV1M SOFTWARE INTERFACE When using the WM8973-EV1B evaluation board with a DSP platform, the registers may be set using the supplied software with a PC and parallel port cable as shown in Figure 29. If the DSP is used to write to the WM8973 registers as well as supplying/receiving the audio interface timing and data signals, it is recommended that twisted pair or shielded wires are used to connect the DSP platform to the WM8973-EV1B. If the DSP supplies are set to the same voltage as the DBVDD supplies of the WM8973, a direct connection can be made to pin 6 (CSB), pin 7 (SDIN) and pin 8 (SCLK) of header strip J13 for 3-wire software mode as shown in Figure 30. If the DSP is running at a higher voltage (e.g. +5V) than the WM8973, the signals from the DSP platform should be connected to test points TP2 (CSB), TP4 (SDIN) and TP3 (SCLK). Connecting the higher voltage signals from the DSP to the test points will level shift through the transistors down to the same level as the DBVDD supply as shown in Figure 31. This will ensure that the WM8973 input CMOS thresholds (i.e. Logic High (min) = DBVDDx0.7; Logic Low (max) = DBVDDx0.3) are met and the device will not be damaged. The same connections apply for controlling the WM8973 via 2-wire software mode (i.e. only pin 7 (SDIN) and pin 8 (SCLK) of header strip J13 are used). Pin 6 (CSB) can be pulled low on the board if device address 0011010 [0x34h] is required or pulled high address 0011011 [0x36h] is required. CONNECTION DIAGRAMS Figure 29 DSP Connection with PC Control using Wolfson Software w Rev 1.0, February 2005 37 WM8973-EV1M Figure 30 Full DSP Control with Equal Voltage Supplies for DSP and WM8973 Figure 31 Full DSP Control with Higher Voltage DSP Supply than WM8973 w Rev 1.0, February 2005 38 WM8973-EV1M ADDITIONAL WM8973-EV1B SETUP RECOMMENDATIONS ADC TO DAC LOOPBACK Setting up the WM8973-EV1 in loopback mode allows an analogue signal to be applied to L/RLINE_IN1, passed through the ADC, looped into the DAC and output on the L/ROUT outputs. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 LOUT1 ROUT1 ROUT2 LOUT2 OUT3 MONO OUT Figure 32 Recommended ADC to DAC Loopback Setup Note: Pin 6 of H1 MUST be linked to pin 9 of H2. A digital input must also be applied to U3 or J19 so that the correct clocks are supplied to the WM8973. w Rev 1.0, February 2005 39 WM8973-EV1M LINKS AND JUMPERS LINK/JUMPER STATUS DESCRIPTION H1 All jumpers in place except for links shorting pins 5 and 6 and 7 and 8. DAC clocks and data input H2 All jumpers in place except for links shorting pins 9 and 10 and 11 and 12. ADC clocks and data output SW36 Pins 2 and 3 SHORT Connects to GND for HP output reference J18 (BCLK) SHORT Slave mode J20 (ADCLRC) SHORT Slave mode J25 (DACLRC) SHORT Slave mode J23 SHORT Slave mode J32, J33, J34 and J35 OPEN OUT signals are AC coupled SW3 1 1 2 0 3 0 4 1 5 0 6 0 DATA FORMAT I2S Compatible SW4 Pins 1 and 2 SHORT 3-wire (SPI) Control Mode SW1, SW2 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW5, SW7 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW8, SW9 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW27, SW28 Pins 2 and 3 SHORT Line Output Select (Phono Socket) Table 14 Loopback Setup Jumper Settings (Slave Mode) SOFTWARE SETUP 1. Press the `ADC Setup' button. 2. Open the Power Down Control panel and set the DAC and L/ROUT1 bits `active'. 3. Open the ADC and DAC Control panel. Uncheck the DAC Mute button. 4. Open the Volume Control panel. Set the DAC and L/ROUT1 Volume Update buttons. 5. Open the Mixer Control panel. Set the Right DAC to Right Mixer and Left DAC to Left Mixer switches to `Enable'. CONNECTION OF AN 8 MONO SPEAKER The WM8973-EV1 can be set up to drive an 8 mono speaker from the R/LOUT2 outputs. Figure 33 shows the setup required for a signal applied to the DAC signal path to be output on a speaker being driven from the phono connectors J41 and J42. As stated in Table 7, the speaker may also be attached to jumpers J37 and J38. w Rev 1.0, February 2005 40 WM8973-EV1M DGND DBVDD +1.8V to +3.6V AVDD +1.8V to +3.6V AGND J4 J5 PARALLEL PORT J1 +5V J2 1 J8 J6 SW1 OPEN 1 0 SW3 1 2 3 4 5 J10 RLINE IN1 1 1 DCVDD +1.42V to +3.6V 6 SW4 SW2 1 1 LLINE IN1 J11 H1 J13 SW6 RLINE IN2 J17 SW5 1 1 J15 1 1 SW7 1 LLINE IN2 1 SPDIF_ IN J20 J23 J21 J25 H2 RLINE IN3 1 1 1 1 SW9 1 1 LLINE IN3 1 J38 J37 1 1 J31 J33 J32 J35 J34 SW36 SW8 SW28 SW27 1 SPDIF_ OUT 1 J24 1 J18 OPT _IN 1 J47 LOUT1 ROUT1 ROUT2 LOUT2 OUT3 MONO OUT -ve Output +ve Output 8 HPVDD +1.8V to +3.6V Figure 33 Recommended Mono Speaker Connection Setup Note: LOUT2 = +ve output; ROUT2 = -ve output. w Rev 1.0, February 2005 41 WM8973-EV1M LINKS AND JUMPERS LINK/JUMPER STATUS DESCRIPTION H1 All jumpers in place. DAC clocks and data input H2 No jumpers in place. ADC clocks and data output SW36 Pins 2 and 3 SHORT Connects to GND for HP output reference J18 (BCLK) SHORT Slave mode J20 (ADCLRC) SHORT Slave mode J25 (DACLRC) SHORT Slave mode J23 SHORT Slave mode J32 and J33 OPEN OUT signals are AC coupled J34 and J35 SHORT OUT signals are DC coupled SW3 1 1 2 0 3 0 4 1 5 0 6 0 DATA FORMAT I2S Compatible SW4 Pins 1 and 2 SHORT 3-wire (SPI) Control Mode SW1, SW2 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW5, SW7 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW8, SW9 Pins 2 and 3 SHORT Line Input Select (Phono Socket) SW27, SW28 Pins 2 and 3 SHORT Line Output Select (Phono Socket) Table 15 DAC to Mono Speaker Setup Jumper Settings (Slave Mode) SOFTWARE SETUP w 1. Press the `DAC Setup' button. 2. Open the Mixer Control panel. Set the `ROUT2 Invert' switch to Signal Inverted followed by the `Mixer Submit' button. Rev 1.0, February 2005 42 WM8973-EV1M HEADPHONE AUTO-DETECT FUNCTION DGND DBVDD +1.8V to +3.6V J1 J2 AVDD +1.8V to +3.6V AGND J4 J5 PARALLEL PORT J8 DCVDD +1.42V to +3.6V J10 1 +5V J6 OPEN SW3 RLINE IN1 SW1 1 0 1 1 1 2 3 4 5 6 SW4 SW2 1 1 LLINE IN1 J11 H1 J13 SW6 RLINE IN2 J17 SW5 1 1 J15 SW7 1 1 1 J24 LLINE IN2 1 SPDIF_ IN J20 J23 J21 J25 H2 RLINE IN3 1 1 1 1 SW9 1 1 LLINE IN3 1 J38 J37 1 1 J31 J33 J32 J35 J34 J36 1 SPDIF_ OUT SW8 J28 J27 1 OPT _IN 1 J18 1 J47 LOUT1 ROUT1 LOUT2 ROUT2 OUT3 MONO OUT HPVDD +1.8V to +3.6V Figure 34 Headphone Auto Detect Setup One of the features of the WM8973 is a headphone auto-detect function. This can be enabled on the WM8973-EV1B by the making the following hardware and software settings. HARDWARE SETUP 1. Designator R50 should be populated with a 0R resistor. 2. Switch SW8 should be set to the OFF (centre) position. 3. Designator R49 should be populated with a 47K resistor. 4. Connect speakers to the R/LOUT2 outputs. 5. For this recommended setup the rest of the jumper and switch settings should be as shown in Table 7. SOFTWARE SETUP 1. Press the `DAC Setup' button. 2. Open the Tone Control panel and set the `Headphone Switch' to Enable. Press the Tone Submit button. The headphone auto-detect function should now be active. With no headphone connected to the 3.5mm jack socket (J46) audio should be output from the speakers connected to R/LOUT2. When the headphone is plugged into 3.5mm jack socket (J46), the audio should not be output from the speakers connected to R/LOUT2 and only be output from the headphones. Refer to the WM8973 datasheet for further details of this, and all other functions offered by the WM8973. w Rev 1.0, February 2005 43 WM8973-EV1M EVALUATION SUPPORT The aim of this evaluation kit is to help you to become familiar with the functionality and performance of the WM8973 CODEC. If you require more information or require technical support please contact Wolfson Microelectronics Applications group through the following channels: Email: apps@wolfsonmicro.com Telephone Apps: (+44) 131 272 7070 Fax: (+44) 131 272 7001 Mail: Applications Department at address on last page. or contact your local Wolfson representative. Additional information may be made available from time to time on our web site at http://www.wolfsonmicro.com w Rev 1.0, February 2005 44 WM8973-EV1M IMPORTANT NOTICE Wolfson Microelectronics plc (WM) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current. All products are sold subject to the WM terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. WM warrants performance of its products to the specifications applicable at the time of sale in accordance with WM's standard warranty. Testing and other quality control techniques are utilised to the extent WM deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. In order to minimise risks associated with customer applications, adequate design and operating safeguards must be used by the customer to minimise inherent or procedural hazards. Wolfson products are not authorised for use as critical components in life support devices or systems without the express written approval of an officer of the company. Life support devices or systems are devices or systems that are intended for surgical implant into the body, or support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided, can be reasonably expected to result in a significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. WM assumes no liability for applications assistance or customer product design. WM does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of WM covering or relating to any combination, machine, or process in which such products or services might be or are used. WM's publication of information regarding any third party's products or services does not constitute WM's approval, license, warranty or endorsement thereof. Reproduction of information from the WM web site or datasheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated WM product or service, is an unfair and deceptive business practice, and WM is not responsible nor liable for any such use. Resale of WM's products or services with statements different from or beyond the parameters stated by WM for that product or service voids all express and any implied warranties for the associated WM product or service, is an unfair and deceptive business practice, and WM is not responsible nor liable for any such use. ADDRESS: Wolfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: apps@wolfsonmicro.com w Rev 1.0, February 2005 45 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cirrus Logic: WM8973L-6097-FL32-M WM8973L-6097-FL32-M-S