CIN: TAIYO YUDEN X5R JMK325BJ226MM
CCUK: TAIYO YUDEN X5R EMK316BJ105MF
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CR32-150
L2: SUMIDA CR32-470
CCUK
1 PF
COUT
22 PF
L2
47 PH
VIN
5V
D
CFF
330 pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22 PF
L1
15 PHVOUT - 5V
300 mA
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
LM2611 1.4-MHz Cuk Converter
1 Features 3 Description
The LM2611 is a current mode, PWM inverting
1• 1.4-MHz Switching Frequency switching regulator. Operating from a 2.7-V to 4-V
• Low RDS(ON) DMOS FET supply, it is capable of producing a regulated
• 1-mVp-p Output Ripple negative output voltage of up to −(36 VIN(MAX)). The
LM2611 utilizes an input and output inductor, which
•−5 V at 300 mA From 5-V Input enables low voltage ripple and RMS current on both
• Better Regulation Than a Charge Pump the input and the output. With a switching frequency
• Uses Tiny Capacitors and Inductors of 1.4 MHz, the inductors and output capacitor can be
physically small and low cost. High efficiency is
• Wide Input Range: 2.7 V to 14 V achieved through the use of a low RDS(ON) FET.
• Low Shutdown Current: <1 µA The LM2611 features a shutdown pin, which can be
• 5-Pin SOT-23 Package activated when the part is not needed to lower the Iq
and save battery life. A negative feedback (NFB) pin
2 Applications provides a simple method of setting the output
• MR Head Bias voltage, using just two resistors. Cycle-by-cycle
• Digital Camera CCD Bias current limiting and internal compensation further
simplify the use of the LM2611.
• LCD Bias The LM2611 is available as a small 5-pin, SOT-23
• GaAs FET Bias package and comes in two grades. Grade A has a
• Positive to Negative Conversion 1.2-A current limit and 0.5-ΩRDS(ON), and Grade B
has a 0.9-A current limit and 0.7-ΩRDS(ON).
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LM2611 SOT-23 (5) 1.60 mm × 2.90 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application Circuit
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
Table of Contents
7.3 Feature Description................................................... 8
1 Features.................................................................. 17.4 Device Functional Modes........................................ 12
2 Applications ........................................................... 18 Application and Implementation ........................ 13
3 Description............................................................. 18.1 Application Information............................................ 13
4 Revision History..................................................... 28.2 Typical Application.................................................. 13
5 Pin Configuration and Functions......................... 39 Power Supply Recommendations...................... 19
6 Specifications......................................................... 310 Layout................................................................... 20
6.1 Absolute Maximum Ratings ...................................... 310.1 Layout Guidelines ................................................. 20
6.2 ESD Ratings.............................................................. 310.2 Layout Example .................................................... 20
6.3 Recommended Operating Conditions....................... 411 Device and Documentation Support................. 21
6.4 Thermal Information.................................................. 411.1 Community Resources.......................................... 21
6.5 Electrical Characteristics........................................... 411.2 Trademarks........................................................... 21
6.6 Typical Characteristics.............................................. 611.3 Electrostatic Discharge Caution............................ 21
7 Detailed Description.............................................. 811.4 Glossary................................................................ 21
7.1 Overview................................................................... 812 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagram......................................... 8Information........................................................... 21
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision I (April 2013) to Revision J Page
• Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section.................................................................................................. 1
Changes from Revision H (April 2013) to Revision I Page
• Changed layout of National Data Sheet to TI format ........................................................................................................... 19
2Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
1
2
3NFB
SW
GND
5VIN
4 SHDN
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
5 Pin Configuration and Functions
DBV Package
5-Pin SOT-23
Top View
Pin Functions
PIN TYPE(1) DESCRIPTION
NO. NAME
1 SW A Drain of internal switch. Connect at the node of the input inductor and Cuk capacitor.
2 GND GND Analog and power ground.
3 NFB A Negative feedback. Connect to output via external resistor divider to set output voltage.
4 SHDN I Shutdown control input. VIN = Device on. Ground = Device in shutdown.
Analog and power input. Filter out high frequency noise with a 0.1-µF ceramic capacitor
5 VIN PWR placed close to the pin.
(1) A = Analog, I = Input, GND = Ground, PWR = Power
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Input voltage, VIN 14.5 V
SW voltage –0.4 36 V
NFB voltage –6 0.4 V
SHDN voltage –0.4 14.5 V
Maximum junction temperature 125 °C
Power dissipation (2) Internally limited
Lead temperature 300 °C
Storage temperature, Tstg −65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, θJA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance of various layouts.
The maximum allowable power dissipation at any ambient temperature is calculated using: PD(MAX) = (TJ(MAX) −TA)/θJA. Exceeding
the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown.
6.2 ESD Ratings VALUE UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)(2) ±2000
V(ESD) Electrostatic discharge V
Machine Model (MM)(3) ±200
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) The human body model is a 100-pF capacitor discharged through a 1.5-kΩresistor into each pin.
(3) The machine model is a 200-pF capacitor discharged directly into each pin.
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM2611
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
6.3 Recommended Operating Conditions MIN NOM MAX UNIT
Supply voltage 2.7 14 V
Operating junction temperature, TJ−40 125 °C
6.4 Thermal Information LM2611
THERMAL METRIC(1) DBV (SOT-23) UNIT
5 PINS
RθJA Junction-to-ambient thermal resistance 163.5 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 115.2 °C/W
RθJB Junction-to-board thermal resistance 27.4 °C/W
ψJT Junction-to-top characterization parameter 12.9 °C/W
ψJB Junction-to-board characterization parameter 26.9 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance n/a °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics
Specifications in standard type face are for TJ= 25°C, unless otherwise specified. VIN = 5 V and IL= 0 A, unless otherwise
specified. PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
VIN Input voltage TJ=−40°C to +85°C 2.7 14 V
Grade A 1.2
Grade A; TJ=−40°C to +85°C 1 2
ISW Switch current limit A
Grade B 0.9
Grade B; TJ=−40°C to +85°C 0.7
Grade A 0.5 0.65
RDSON Switch ON resistance Ω
Grade B 0.7 0.9
Device enabled; TJ=−40°C to +85°C 1.5
SHDNTH Shutdown threshold V
Device disabled; TJ=−40°C to +85°C 0.5
VSHDN = 0 V 0
ISHDN Shutdown pin bias current VSHDN = 5 V 0 µA
VSHDN = 5 V; TJ=−40°C to +85°C 1
VIN = 3 V −1.23
NFB Negative feedback reference V
VIN = 3 V; TJ=−40°C to +85°C −1.205 −1.255
VNFB =−1.23 V −4.7
INFB NFB pin bias current µA
VNFB =−1.23 V; TJ=−40°C to +85°C −2.7 −6.7
VSHDN = 5 V, Switching 1.8 mA
VSHDN = 5 V, Switching; 3.5
TJ=−40°C to +85°C
VSHDN = 5 V, Not Switching 270
IqQuiescent current µA
VSHDN = 5 V, Not Switching; 500
TJ=−40°C to +85°C
VSHDN = 0 V 0.024 µA
VSHDN = 0 V; TJ=−40°C to +85°C 1
%VOUT/Reference line regulation 2.7 V ≤VIN ≤14 V 0.02 %/V
ΔVIN
(1) All limits are specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits
are 100% tested through statistical analysis. All limits at temperature extremes via correlation using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(2) Typical numbers are at 25°C and represent the expected value of the parameter.
4Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Electrical Characteristics (continued)
Specifications in standard type face are for TJ= 25°C, unless otherwise specified. VIN = 5 V and IL= 0 A, unless otherwise
specified. PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
TJ= 25°C 1.4
fSSwitching frequency MHz
TJ=−40°C to +85°C 1 1.8
TJ= 25°C 88%
DMAX Maximum duty cycle TJ=−40°C to +85°C 82%
ILSwitch leakage VSW = 5 V, Not Switching 1 µA
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM2611
1.30
1.32
1.34
1.36
1.38
1.40
1.42
1.44
1.46
1.48
0246 8 10 12 14
VIN (V)
OSCILLATOR FREQUENCY (MHz)
1.32
1.34
1.36
1.38
1.40
1.42
1.44
1.46
1.48
1.50
TEMPERATURE (oC)
OSCILLATOR FREQUENCY (MHz)
1.30
-60-40 -20 020 40 60 80 100120140 160
1.15
1.2
1.25
1.3
1.35
1.4
1.45
246810 12
VIN (V)
SWITCH CURRENT LIMIT (A)
-50 TEMPERATURE (oC)
SWITCH CURRENT LIMIT (A)
0 50 100 150
1.35
1.36
1.37
1.38
1.39
1.4
RDS(ON) (:)
0
0.2
0.4
0.6
0.8
1
-50 0 50 100 150
TEMPERATURE (oC)
0.3
0.35
0.4
0.45
0.5
0.55
2 4 6 8 10 12 14
VIN (V)
RDS(ON) (:)
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
6.6 Typical Characteristics
VIN = 5 V
Figure 1. RDS(ON) vs VIN Figure 2. RDS(ON) vs Ambient Temperature
VIN = 5 V
Figure 4. Switch Current Limit vs Ambient Temperature
Figure 3. Switch Current Limit vs VIN
VIN = 5 V
Figure 5. Oscillator Frequency vs VIN Figure 6. Oscillator Frequency vs Ambient Temperature
6Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
220
225
230
235
240
245
250
255
260
-50 0 50 100 150
IQ(PA)
TEMPERATURE (oC)
0.5
0.55
0.6
0.65
0.7
0.75
0.8
0.85
0.9
-50 0 50 100 150
TEMPERATURE (oC)
SHUTDOWN VOLTAGE (V)
Off Threshold
On Threshold
3.9
4.0
4.1
4.2
4.3
4.4
-50 0 50 100 150
TEMPERATURE (oC)
INFB (PA)
-25 25 75 125
4.2
4.25
4.3
4.35
4.4
4.45
0510 15
VIN (V)
INFB (PA)
-1.232
-1.230
-1.228
-1.226
-1.224
-1.222
-1.220
-1.218
-55 -30 -5 20 45 70 95 120
VNFB (V)
TEMPERATURE (oC)
-1.25
-1.245
-1.24
-1.235
-1.23
-1.225
-1.22
-1.215
0510 15
VIN (V)
VNFB (V)
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Typical Characteristics (continued)
TA= 25°C VOUT =−5 V VIN = 5 V
Figure 7. VNFB vs VIN Figure 8. VNFB vs Ambient Temperature
TA= 25°C VOUT =−5 V VIN = 3.5 V VOUT =−5 V
Figure 9. INFB vs VIN Figure 10. INFB vs Ambient Temperature
VIN = 5 V
Figure 12. VSHUTDOWN vs Ambient Temperature
Figure 11. Iqvs Ambient Temperature (No Load)
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM2611
+ L1 - - L2 + + L1 - - L2 +
VIN
VIN COUT COUT
VOUT
+ CCUK -
+
-
VOUT
+ CCUK -
+
-
ab
PWM COMPARATOR
¦
Q1 Q2
x10
R3
30k
R4
140k
R5 R6
RC
CC
RAMP
GENERATOR
1.4MHz
OSCILLATOR
Q
R
s
R
0.05
CURRENT LIMIT
COMPARATOR
DRIVER
+
-
-
+
gm
-
+
R1
EXTERNAL
R2
EXTERNAL
CFF
(OPTIONAL)
1 SW
2 GND
5
3 NFB
4
VI
N
SHDN
SHUTDOWN
FF
VO
R
THERMAL
SHUTDOWN
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LM2611 consists of a current mode controller with an integrated primary switch and integrated current
sensing circuitry. The feedback is connected to the internal error amplifier and a type II/III internal compensation
scheme is used. A ramp generator provides some slope compensation to the system. SHDN pin is a logic input
designed to shut down the converter.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Cuk Converter
Figure 13. Operating Cycles of a Cuk Converter
The LM2611 is a current mode, fixed frequency PWM switching regulator with a −1.23-V reference that makes it
ideal for use in a Cuk converter. The Cuk converter inverts the input and can step up or step down the absolute
value. Using inductors on both the input and output, the Cuk converter produces very little input and output
current ripple. This is a significant advantage over other inverting topologies such as the buck-boost and flyback.
The operating states of the Cuk converter are shown in Figure 13. During the first cycle, the transistor switch is
closed and the diode is open. L1 is charged by the source and L2 is charged by CCUK, while the output current is
provided by L2. In the second cycle, L1 charges CCUK and L2 discharges through the load. By applying the volt-
second balance to either of the inductors, use Equation 1 to determine the relationship of VOUT to the duty cycle
(D).
8Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
CIN: VISHAY/SPRAGUE 595D226X0020C2T
CCUK: TAIYO YUDEN X5R LMK212BJ105MG
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CLS62-220 or MURATA LZH3C220 (UNCOUPLED)
L1A
22PHCCUK
2.2PF
COUT
22PF
L1B
22PH
VIN
12V
VOUT-5V
375mA
VDD
5V D
CFF
1000pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22PF
IL1
vL1(V)
iL1(A)
'IL1
VIN
VOUT
t
t
OUT IN
D
V V
1-D
= -
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Feature Description (continued)
(1)
The following sections review the steady-state design of the LM2611 Cuk converter.
7.3.2 Output and Input Inductor
Figure 14 and Figure 15 show the steady-state voltage and current waveforms for L1 and L2, respectively.
Referring to Figure 13 (a), when the switch is closed, VIN is applied across L1. In the next cycle, the switch opens
and the diode becomes forward biased, and VOUT is applied across L1 (the voltage across CCUK is VIN −VOUT.)
Figure 14. Voltage and Current Waveforms in Inductor L1 of a Cuk Converter
The voltage and current waveforms of inductor L2 are shown in Figure 15. During the first cycle of operation,
when the switch is closed, VIN is applied across L2. When the switch opens, VOUT is applied across L2.
Figure 15. Schematic of the Cuk Converter Using LM2611
Equation 2 to Equation 5 define the values given in Figure 14 and Figure 15:
IL2 = IOUT (2)
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM2611
IN
CIN(RMS)
i
s 1
o
V
1
I2 3 V
f L 1
V
=æ ö
+
ç ÷
ç ÷
è ø
iSW(A)
IL1+ IL2
t
ICL
ISW
'iL1 +'iL2
iSW
SW(PEAK ) L1 L2 L1 L2 L1 L2
IN S
OUT
1 2
i i i I I i i
V D T
D 1 1
I 1 1-D 2 L L
= + = + + D + D
æ ö
´ ´
æ ö
= ´ + + ´ +
ç ÷
ç ÷
è ø è ø
IN S
L1
1
V D T
i
2 L
´ ´
D =
´
L1 L2 OUT
D D
I I I
1-D 1-D
= =
IN S
L2
2
V D T
i
2 L
´ ´
D =
´
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
Feature Description (continued)
(3)
(4)
(5)
Use these equations to choose correct core sizes for the inductors. The design of the LM2611's internal
compensation assumes L1 and L2 are equal to 10 to 22 µH, thus TI recommends staying within this range.
7.3.3 Switch Current Limit
The LM2611 incorporates a separate current limit comparator, making current limit independent of any other
variables. The current limit comparator measures the switch current versus a reference that represents current
limit. If at any time the switch current surpasses the current limit, the switch opens until the next switching period.
To determine the maximum load for a given set of conditions, both the input and output inductor currents must be
considered. The switch current is equal to iL1 + iL2, and is drawn in Figure 16. In summary, Equation 6 shows:
(6)
ISW(PEAK) must be less than the current limit (1.2 A typical), but will also be limited by the thermal resistivity of the
LM2611 device's 5-pin, SOT-23 package (θJA = 265°C/W).
The peak value is equal to the sum of the average currents through L1 and L2 and the average-to-peak current
ripples through L1 and L2.
Figure 16. Switch Current Waveform in a Cuk Converter.
7.3.4 Input Capacitor
The input current waveform to a Cuk converter is continuous and triangular, as shown in Figure 14. The input
inductor insures that the input capacitor sees fairly low ripple currents. However, as the input inductor gets
smaller, the input ripple goes up. The RMS current in the input capacitor is shown in Equation 7.
(7)
The input capacitor should be capable of handling the RMS current. Although the input capacitor is not so critical
in a Cuk converter, a 10-µF or higher value good quality capacitor prevents any impedance interactions with the
input supply. TI recommends connecting a 0.1-µF or 1-µF ceramic bypass capacitor on the VIN pin (pin 5) of the
IC. This capacitor must be connected very close to pin 5 (within 0.2 inches).
10 Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
FB1
p
FF FB1 FB2
R
11 (rad / s)
C R R
æ ö
w = +
ç ÷
è ø
Z
FF FB1
1(rad / s)
C R
w =
ESR
OUT
1
f (Hz)
2 C ESR
=
p
L2 IN
COUT(RMS)
i
s 2
o
i V
1
I3 2 3 V
f L 1
V
D
= = æ ö
+
ç ÷
ç ÷
è ø
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Feature Description (continued)
7.3.5 Output Capacitor
Like the input current, the output current is also continuous, triangular, and has low ripple (see IL2 in Figure 15).
The output capacitor must be rated to handle its RMS current:
(8)
For example, ICOUT(RMS) can range from 30 mA to 180 mA with 10 µH ≤L1,2 ≤22 µH, −10 V ≤VOUT ≤ −3.3 V, and
2.7 V ≤VIN ≤30 V (VIN may be 30 V if using separate power and analog supplies, see Split Supply Operation in
the Typical Application section). The worst case conditions are with L1,2, VOUT(MAX), and VIN(MAX). Many capacitor
technologies will provide this level of RMS current, but ceramic capacitors are ideally suited for the LM2611.
Ceramic capacitors provide a good combination of capacitance and equivalent series resistance (ESR) to keep
the zero formed by the capacitance and ESR at high frequencies. Use Equation 9 to calculate the ESR zero.
(9)
A general rule of thumb is to keep fESR > 80 kHz for LM2611 Cuk designs. Low ESR tantalum capacitors will
usually be rated for at least 180 mA in a voltage rating of 10 V or above. However the ESR in a tantalum
capacitor (even in a low ESR tantalum capacitor) is much higher than in a ceramic capacitor and could place fESR
low enough to cause the LM2611 to become unstable.
7.3.6 Improving Transient Response and Compensation
The compensator in the LM2611 is internal. However, a zero-pole pair can be added to the open-loop frequency
response by inserting a feed-forward capacitor, CFF, in parallel to the top feedback resistor (RFB1). Phase margin
and bandwidth can be improved with the added zero-pole pair. This in turn improves the transient response to a
step load change (see Figure 17 and Figure 18). The position of the zero-pole pair is a function of the feedback
resistors and the capacitor value:
(10)
(11)
The optimal position for this zero-pole pair will vary with circuit parameters such as D, IOUT, COUT, L1, L2, and
CCUK. For most cases, the value for the zero frequency is between 5 kHz to 20 kHz. Notice how the pole
position, ωp, is dependant on the feedback resistors RFB1 and RFB2, and therefore also dependant on the output
voltage. As the output voltage becomes closer to −1.26 V, the pole moves towards the zero, tending to cancel it
out. If the absolute magnitude of the output voltage is less than 3.3 V, adding the zero-pole pair will not have
much effect on the response.
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM2611
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
Feature Description (continued)
Figure 17. 130-mA to 400-mA Transient Response Figure 18. 130-mA to 400-mA Transient Response
of the Circuit in Figure 24 With CFF= 1 nF of the Circuit in Figure 24 With CFF Disconnected
7.4 Device Functional Modes
7.4.1 Hysteretic Mode
As the output current decreases, the energy stored in the Cuk capacitor eventually exceeds the energy required
by the load. The excess energy is absorbed by the output capacitor, causing the output voltage to increase out of
regulation. The LM2611 detects when this happens and enters a pulse-skipping, or hysteretic mode. In pulse-
skipping mode, the output voltage increases as illustrated in Figure 20 as opposed to the regular PWM operation
shown in Figure 19.Figure 19 shows the LM2611 in PWM Mode with very-low ripple. Figure 20 shows the
LM2611 in pulse-skipping mode at low loads. In this mode, the output ripple increases slightly.
Figure 19. PWM Mode Figure 20. Pulse-Skipping Mode
7.4.1.1 Thermal Shutdown
If the junction temperature of the LM2611 exceeds 163°C, the device enters thermal shutdown. In thermal
shutdown, the part deactivates the driver and the switch turns off. The switch remains off until the junction
temperature drops to 155°C, at which point the part begins switching again. It will typically take 10 ms for the
junction temperature to drop from 163°C to 155°C with the switch off.
12 Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
CIN: VISHAY/SPRAGUE 595D226X0020C2T
CCUK: TAIYO YUDEN X5R LMK212BJ105MG
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CLS62-220 or MURATA LZH3C220 (UNCOUPLED)
L1A
22PHCCUK
2.2PF
COUT
22PF
L1B
22PH
VIN
12V
VOUT-5V
375mA
VDD
5V D
CFF
1000pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22PF
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM2611 is a Cuk controller with an integrated switch. The following section provides an approach to sizing
the components for the target application and shows some typical examples of applications to help the designer.
8.2 Typical Application
8.2.1 Cuk Converter With Integrated Switch
Figure 21. Typical Cuk Converter Implementation Using LM26211
8.2.1.1 Design Requirements
The first variables needed are the output voltage and the input voltage range (min to max). The input voltage
range ensures that the IC is suitable for the application and that the absolute maximum voltage are respected.
The expected maximum output current is also needed to verify that the IC can deliver the required current.
8.2.1.2 Detailed Design Procedure
The first components to choose are the power inductors. Typically a smaller inductance yields a smaller solution
footprint and lower cost but the higher ripple makes a smaller inductance not compatible with every application.
Due to the internal compensation, TI recommends a 10-µH to 22-µH inductor. Try to choose the inductors so that
the peak-to-peak ripple is lower than 0.3 A of the average current by using Equation 3 and Equation 5.
Using the maximum output current and the input voltage range, calculate the worst case peak current in the
switch using Equation 6. If the peak current is above the peak current limit for this part, consider increasing the
inductance and re-calculate. If the inductance is above 22 µH for each inductor, the designer will have to pay
special attention to stability over the extended range of operation (it's always a good practice to do so even if the
inductance is within the recommended range).
Using the desired output voltage, calculate the value of the feedback resistors. The reference voltage is 1.23 V.
Resistors of 50 kΩor less must be used due to the leakage at the NFB pin.
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM2611
CIN: TAIYO YUDEN X5R JMK325BJ226MM
CCUK: TAIYO YUDEN X5R EMK316BJ105MF
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CR32-150
L2: SUMIDA CR32-470
CCUK
1 PF
COUT
22 PF
L2
47 PH
VIN
5V
D
CFF
330 pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22 PF
L1
15 PHVOUT - 5V
300 mA
46 8 10 12 14 16 18 20
0
100
200
300
400
500
600
700
57 9 11 13 15 17 19
OUTPUT VOLTAGE (-V)
MAXIMUM OUTPUT CURRENT (mA)
46 8 10 12 14 16 18 20
0
100
200
300
400
500
600
700
57 9 11 13 15 17 19
OUTPUT VOLTAGE (-V)
MAXIMUM OUTPUT CURRENT (mA)
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
Typical Application (continued)
It is a good idea to add a placeholder for a small capacitor across the top feedback resistor to act as a feed-
forward component to optimize transient response. Optimization of the feed-forward capacitor depends a lot on
the specific parameters including the parasitic components associated with the capacitors. Experimentation is
key to ensure ideal sizing of the capacitor (either using load transient response or a loop response analyzer).
See Improving Transient Response and Compensation for details regarding the CFF capacitor.
8.2.1.3 Application Curves
Figure 22. Maximum Output Current vs Output Voltage at Figure 23. Maximum Output Current vs Output Voltage at
VIN = 12 V (L1 = L2 = 22 µH) VIN = 5 V (L1 = L2 = 22 µH)
8.2.2 5-V to –5-V Inverting Converter
Figure 24. 5-V to –5-V Inverting Converter Schematic
8.2.2.1 Design Requirements
This design converts 5 V (VIN) to –5 V (VOUT). Adjust RFB2 to set a different output voltage.
14 Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
CIN: TAIYO YUDEN X5R JMK325BJ226MM
CCUK: TAIYO YUDEN X5R EMK316BJ105MF
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CR32-100
L2: SUMIDA CR32-100
CCUK
1 PF
COUT
22 PF
L2
10 PH
VIN
9V
D
CFF
330 pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22 PF
L1
10 PHVOUT - 5V
46 8 10 12 14 16 18 20
0
100
200
300
400
500
600
700
57 9 11 13 15 17 19
OUTPUT VOLTAGE (-V)
MAXIMUM OUTPUT CURRENT (mA)
0.05 0.15 0.25
40
45
50
55
60
65
70
75
80
85
90
LOAD CURRENT (A)
EFFICIENCY (%)
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Typical Application (continued)
8.2.2.2 Application Curves
Figure 25. Efficiency vs Load Current Figure 26. Maximum Output Current vs Output Voltage, 5
V to –5 V
8.2.3 9-V to –5-V Inverting Converter
Figure 27. 9-V to –5-V Inverting Converter Schematic
8.2.3.1 Design Requirements
This design converts 9 V (VIN) to –5 V (VOUT). Adjust RFB2 to set a different output voltage.
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM2611
CIN: TAIYO YUDEN X5R JMK325BJ226MM
CCUK: TAIYO YUDEN X5R EMK316BJ225ML
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CR32-220
L2: SUMIDA CR32-220
CCUK
2.2 PF
COUT
22 PF
L2
22 PH
VIN
12V
D
CFF
1000 pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22 PF
L1
22 PHVOUT - 5V
46 8 10 12 14 16 18 20
0
10
0
20
0
30
0
40
0
50
0
60
0
OUTPUT VOLTAGE (-V)
MAXIMUM OUTPUT CURRENT (mA)
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
700
600
500
400
300
200
100
0
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
Typical Application (continued)
8.2.3.2 Application Curve
Figure 28. Maximum Output Current vs Output Voltage, 9 V to – 5 V
8.2.4 12-V to –5-V Inverting Converter
The maximum output current vs output voltage (adjust RFB2 to set a different output voltage) when the input voltage is
12 V.
Figure 29. 12-V to –5-V Inverting Converter Schematic
8.2.4.1 Design Requirements
This design converts 12 V (VIN) to –5 V (VOUT). Adjust RFB2 to set a different output voltage.
16 Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
CIN: VISHAY/SPRAGUE 595D226X0020C2T
CCUK: TAIYO YUDEN X5R EMK316BJ225ML
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1: SUMIDA CR32-220
L1A
22PHCCUK
2.2PF
COUT
22PF
L1B
22PH
VIN
12V
VOUT-5V
375mA
VDD
5V D
CFF
1000pF
RFB1
29.4k
RFB2
10k
VIN SW
NFB
GND
SHDN LM2611A
1
2
34
5
CIN
22PF
CBYP
0.1PF
46 8 10 12 14 16 18 20
0
100
200
300
400
500
600
700
57 9 11 13 15 17 19
OUTPUT VOLTAGE (-V)
MAXIMUM OUTPUT CURRENT (mA)
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Typical Application (continued)
8.2.4.2 Application Curve
Figure 30. Maximum Output Current vs Output Voltage, 12 V to –5 V
8.2.5 LM2611 Operating With Separate Power and Biasing Supplies
Figure 31. LM2611 Operating With Separate Power and Biasing Supplies Schematic
8.2.5.1 Design Requirements
Follow the design requirements in Cuk Converter With Integrated Switch.
8.2.5.2 Detailed Design Procedure
8.2.5.2.1 Split Supply Operation
The LM2611 may be operated with separate power and bias supplies. In the circuit shown in Figure 31, VIN is the
power supply that the regulated voltage is derived from, and VDD is a low current supply used to bias the
LM2611. Equation 12 and Equation 13 show the conditions for the supplies are:
2.7 V ≤VDD ≤14 V (12)
0 V ≤VIN ≤(36 - IVOUTI) V (13)
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM2611
L1A
22uH
L1B
22uH
CCUK
1uF
CIN
22uF COUT
22uF
CFF
1000pF
RFB1
29.4k
RFB2
10k
D
VIN
5
SW
1
3
SHDN
4
GND
2
VIN VOUT
RSS
100k VSHDN CSS
0.1uF
NFB
LM2611A
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
Typical Application (continued)
As the input voltage increases, the maximum output current capacbility increases. Using a separate, higher
voltage supply for power conversion enables the LM2611 to provide higher output currents than it would with a
single supply that is limited in voltage by VIN(MAX).
8.2.6 Shutdown and Soft-Start
Figure 32. LM2611 Soft-Start Circuit
8.2.6.1 Design Requirements
Follow the design requirements in Cuk Converter With Integrated Switch.
8.2.6.2 Detailed Design Procedure
8.2.6.2.1 Shutdown and Soft-Start
A soft-start circuit is used in switching power supplies to limit the input inrush current upon start-up. Without a
soft-start circuit, the inrush current can be several times the steady-state load current, and thus apply
unnecessary stress to the input source. The LM2611 does not have soft-start circuitry, but implementing the
circuit in Figure 32 lowers the peak inrush current. The SHDN pin is coupled to the output through CSS. The
LM2611 is toggled between shutdown and run states while the output slowly decreases to its steady-state value.
The energy required to reach steady state is spread over a longer time and the input current spikes decrease
(see Figure 33 and Figure 34).
8.2.6.3 Application Curves
Figure 34. Start-Up Waveforms Without a Soft-Start Circuit
Figure 33. Start-Up Waveforms With a Soft-Start Circuit
18 Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
L1
22uH
L2
22uH
CCUK
1uF
CIN
10uF COUT
22uF
CFF1
1000pF
RFB1
29.4k
RFB2
1k
D
LM2611A
VIN
5
SW
1
NFB
3
SHDN
4
GND
2
VOUT
-5V
CIN: TAIYO YUDEN X5R JMK325BJ106MN
CCUK: TAIYO YUDEN X5R TMK316BJ105ML
COUT: TAIYO YUDEN X5R JMK325BJ226MM
D: ON SEMICONDUCTOR MBR0520
L1, L2: SUMIDA CDRH6D28-220
CFF2
1uF
RFB3
9k
2.7V VIN
d
14V
d
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
Typical Application (continued)
8.2.7 High Duty Cycle and Load Current
Figure 35. LM2611 High Current Schematic
8.2.7.1 Design Requirements
Follow the design requirements in Cuk Converter With Integrated Switch.
8.2.7.2 Detailed Design Procedure
8.2.7.2.1 High Duty Cycle and Load Current Operation
The circuit in Figure 35 is used for high duty cycles (D > 0.5) and high load currents. The duty cycle begins to
increase beyond 50% as the input voltage drops below the absolute magnitude of the output voltage. RFB3 and
CFF2 are added to the feedback network to introduce a low frequency lag compensation (pole-zero pair)
necessary to stabilize the circuit under the combination of high duty cycle and high load currents.
9 Power Supply Recommendations
The power supply must never exceed the absolute maximum rating of the device given in Absolute Maximum
Ratings. If the regulator is connected to the input supply through long wires or PCB traces, special care is
required to achieve good performance. The parasitic inductance and resistance of the input cables can have an
adverse effect on the operation of the regulator. The parasitic inductance, in combination with the low ESR
ceramic input capacitors, can form an under-damped resonant circuit. This circuit may cause overvoltage
transients at the VIN pin, each time the input supply is cycled on and off.
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM2611
LM2611
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
www.ti.com
10 Layout
10.1 Layout Guidelines
• Connection between L1 and SW pin should be kept as short as possible to minimize inductance
• Connection between CCUK and SW should also be kept short
• The feedback resistor should be placed close to the NFB pin to minimize the path of the higher impedance
feedback node
• The feedback trace leading from Vout to the output to the feedback resistors should not pass under the
switch node between L1 and CCUK and the switch node between CCUK, L2 and D
• The feedback trace leading from Vout to the output to the feedback resistors should not pass under the
inductors L1 and L2
• A bypass capacitor CBYP of 0.1 µF should be placed close to VIN and GND pin
10.2 Layout Example
Figure 36. Example Layout Top
Figure 37. Example Layout Bottom
20 Submit Documentation Feedback Copyright © 2001–2015, Texas Instruments Incorporated
Product Folder Links: LM2611
LM2611
www.ti.com
SNOS965J –JUNE 2001–REVISED DECEMBER 2015
11 Device and Documentation Support
11.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.2 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2001–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM2611
PACKAGE OPTION ADDENDUM
www.ti.com 23-Sep-2015
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2611AMF NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 S40A
LM2611AMF/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 S40A
LM2611AMFX/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 S40A
LM2611BMF/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 S40B
LM2611BMFX/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 S40B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 23-Sep-2015
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2611AMF SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM2611AMF/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM2611AMFX/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM2611BMF/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM2611BMFX/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 20-Dec-2016
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2611AMF SOT-23 DBV 5 1000 210.0 185.0 35.0
LM2611AMF/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM2611AMFX/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM2611BMF/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM2611BMFX/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 20-Dec-2016
Pack Materials-Page 2
www.ti.com
PACKAGE OUTLINE
C
TYP
0.22
0.08
0.25
3.0
2.6
2X 0.95
1.9
1.45 MAX
TYP
0.15
0.00
5X 0.5
0.3
TYP
0.6
0.3
TYP
8
0
1.9
A
3.05
2.75
B
1.75
1.45
(1.1)
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
4214839/C 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
0.2 C A B
1
34
5
2
INDEX AREA
PIN 1
GAGE PLANE
SEATING PLANE
0.1 C
SCALE 4.000
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ARROUND 0.07 MIN
ARROUND
5X (1.1)
5X (0.6)
(2.6)
(1.9)
2X (0.95)
(R0.05) TYP
4214839/C 04/2017
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
PKG
1
34
5
2
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
EXPOSED METAL
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
EXPOSED METAL
www.ti.com
EXAMPLE STENCIL DESIGN
(2.6)
(1.9)
2X(0.95)
5X (1.1)
5X (0.6)
(R0.05) TYP
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
4214839/C 04/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
SYMM
PKG
1
34
5
2
www.ti.com
PACKAGE OUTLINE
C
TYP
0.22
0.08
0.25
3.0
2.6
2X 0.95
1.9
1.45 MAX
TYP
0.15
0.00
5X 0.5
0.3
TYP
0.6
0.3
TYP
8
0
1.9
A
3.05
2.75
B
1.75
1.45
(1.1)
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
4214839/C 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
0.2 C A B
1
34
5
2
INDEX AREA
PIN 1
GAGE PLANE
SEATING PLANE
0.1 C
SCALE 4.000
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ARROUND 0.07 MIN
ARROUND
5X (1.1)
5X (0.6)
(2.6)
(1.9)
2X (0.95)
(R0.05) TYP
4214839/C 04/2017
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
PKG
1
34
5
2
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
EXPOSED METAL
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
EXPOSED METAL
www.ti.com
EXAMPLE STENCIL DESIGN
(2.6)
(1.9)
2X(0.95)
5X (1.1)
5X (0.6)
(R0.05) TYP
SOT-23 - 1.45 mm max heightDBV0005A
SMALL OUTLINE TRANSISTOR
4214839/C 04/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
SYMM
PKG
1
34
5
2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
