Document Number: 57092
Revision 03-Oct-02
www.vishay.com
138
Model RPS
Vishay Spectrol
FEATURES
• Tight Linearity of 2% or Less
• Programmable Temperature Coefficient
• Precision Ultra Long Life Device
• Rugged 10 Million Cycle Life
• Cost Effective in Harsh Environment
• Customised Offset and Gain Control Available
Hall Effect Rotary Position Sensor
PARAMETER UNIT
Electrical Angle Degrees 45, 60, 80, 90° ± 2 degrees
180°, optional*
Electrical Output Range % 0 - 100, 5 - 45, 5 - 95, 10 - 90 of applied Vdd
Customer specific linear outputs available*
Linearity ± % 2 (less than 1 typical)
Output Current mA 2 max. (source or sink)
Over Voltage Protection VDC 18 max
Reverse Voltage Protection VDC - 14.5 max
Supply Voltage VDC 5 ± 10%
Supply Current mA 5 typical
Load Life Hrs Greater than 10,000 at rated load
ESD Sensitivity – 7KV max (Human body model)
Standard electronic assembly practices should be observed
EMI V/M 30, 10Khz to 1000Mhz at 3 meters
ELECTRICAL SPECIFICATIONS
ENVIRONMENTAL SPECIFICATIONS
Low Temperature Operation - 40°C
High Temperature Operation + 85°C
Storage Temperature + 105°C max
Shock 50Gs, 11 ms
Vibration 15Gs. 10 to 2000Hz
*Consult the factory
ORDERING INFORMATION
RPS F W A A 060
MODEL SHAFT SOLDER LINEARITY VOLTAGE ELECTRICAL
ANGLE
F: Flatted S: Solder lug (90° from shaft) 2% A: 0.2V - 2.5V 45 - 180
S: Slotted F: S bent 90° to front B: 0.2V - 4.8V Electrical
B: S bent 90° to back angle in degrees
W: Cable wire length (to be specified)
C: Cable wire W/connector (to be specified)
www.vishay.com
139
Model RPS
Vishay Spectrol
Document Number: 57092
Revision 03-Oct-02
MECHANICAL SPECIFICATIONS
PARAMETER UNIT
Housing – 0.598, 0.015 Depth F.M.S x 1.094, 0.015
diameter. Stainless steel can
Bushing – 3/8 - 32, 0.375 max Length F.M.S Excludes C - RING*
Shaft – 0.249 ± 0.001 diameter, Flatted, Slotted,
Lengths to 1.5 inches*
AR Lugs °2 at 180, on 0.531 radius, 0.125W x 0.128 F.M.S
1 lug optional*
Terminal Style – Solder lugs or wire leads
Mechanical Angle deg 45, 60, 80, 90, 2° 180°, optional*
Rotational Life M 10 (min)
Rotational Torque in - oz 2.0 max. at 25°C with shaft seal
Stop Torque – 5 inch pounds
Push Out – 20 pounds min
Pull Out – 10 pounds min
DIMENSIONS in inches (millimeters)
Hall Effect Rotary Position Sensor
APPLICATIONS
MARINE
Throttle position sensor
Outboard motor
Inboard/outboard (ΙO) based power systems
Diesel engine, electronic injector control
Control position sensor:
Rudder position
Trim tab and plain position
Drive tilt and drive gimbal position
Auto pilot feed back and controls
Drive by wire systems, control and feedback
AUTOMOTIVE
Foot pedal position sensor
Throttle position sensor
Steering position sensor
Suspension system position sensors
Seat position sensor
Mirror position sensor
FORKLIFT - INDUSTRIAL TRUCK - FARM EQUIPMENT:
Throttle/speed control (Forward, Neutral, Reverse)
Foot pedal position sensor
Lift and shuttle position and control
Tilt control and feedback of tilt position
Implement grimbal position and control
Steering position
AIRCRAFT
Rudder, pitch - trim or aileron position
Servo tab position
Flap and slat position
Flap asymmetry sensors/detection
Elevator position
Nose wheel position
Throttle position
Foot pedal position sensor
Fly by wire feedback systems
1.094
0.875
0.112
0.520
0.80
0.375
0.128 123
GND Vdd
0.063 + 0.015
- 0.005
0.047 ± 0.005
0.218 ± 0.002
0.375 ±0.010
NOTE; FLAT WILL EXTEND TO WITHIN 0.062
OF BUSHING WHERE SHAFT LENGTH WILL
NOT PERMIT STANDARD FLAT
MOUNTING SHAFT OUTPUT SLOTTED SHAFT
FLATTED SHAFT
OUTPUT
