DENSEI-LAMBDA ZWS 10 SPECIFICATIONS A153-01-01D 13 14 15 16 17 18 19 20 21 22 23 24 25 26 MODEL ITEMS Nominal Output Voltage V Minimum Output Current A Maximum Output Current A Maximum Peak Output Current (*1) A Maximum Output Power W Maximum Peak Output Power (*1) W Efficiency (Typ) (*2) % Input Voltage Range (*3) Input Current(Typ) Inrush Current(Typ) Output Voltage Range Maximum Ripple & Noise 0 - +60C mV (*10) -10 - 0C mV Maximum Line Regulation (*4,10) mV Maximum Load Regulation (*5,10) mV Maximum Temperature Drift (*6) mV Over Current Protection (*7) Over Voltage Protection (*8) Hold-up Time (Typ) (*2) Parallel Operation Series Operation (*9) Operating Temperature (*11) Operating Humidity Storage Temperature Storage Humidity Cooling Withstand Voltage - 27 28 29 30 31 32 33 Isolation Resistance Vibration Shock Safety Conducted Noise Weight (Typ) Size (WxHxD) 1 2 3 4 5 6 7 8 9 10 11 12 ZWS10-3 ZWS10-12 ZWS10-15 ZWS10-24 5 12 15 24 0 0 0 0 2.0 0.85 0.7 0.45 2.4 1.02 0.84 0.54 10.0 10.2 10.5 10.8 12.0 12.24 12.6 12.96 70 70 71 71 85 - 265VAC (47 - 440Hz) or 110 - 330VDC 0.30A at 100VAC, 0.15A at 200VAC 15A at 100VAC, 30A at 200VAC, Ta=25C, Cold Start +/-10% 120 120 150 150 200 160 160 180 180 200 20 20 48 60 96 40 40 96 120 150 60 60 140 180 280 125% 140% 17ms at 100VAC, 10W, Ta=25C Possible -10C - +50C : 100%, +60C : 70% 30 - 90%RH -30C - +85C 10 - 95%RH Convection Cooling Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA) Output - FG : 500VAC (100mA) for 1min More than 100M at 25C and 70%RH Output - FG 500VDC 10-55Hz (Sweep 1min) Less than 19.6m/s2 X,Y,Z 1h each Less than 196.1m/s2 - Approved by UL60950-1,CSA60950-1,EN60950-1. Built to meet DENAN Built to meet EN55022-B, FCC-ClassB, VCCI-B g 120 mm 50 x 21 x 105 =NOTES= *1. Operating time at peak output is less than 10 seconds. (Duty=0.35) *2. At 100VAC and maximum output current , Ta=25C. *3. For cases where conformance to various safety specs (UL,CSA) are required, to be described as 100 - 240VAC, 50/60Hz on name plate. *4. From 85 - 265VAC and constant load. *5. From Min load - Full load (Maximum Power) and constant input voltage. *6. From -10 - +50C constant input voltage and load. *7. Current limiting with automatic recovery. Avoid to operate over load or dead short for 30 seconds. *8. Over voltage clamping by Zener Diode. *9. Refer to Instruction Manual. *10. Please refer to Fig A for measurement of line & load regulation and ripple voltage. *11. At standard mounting method, Fig B. 3.3 0 2.0 2.4 6.6 7.92 62 ZWS10-5 DENSEI-LAMBDA ZWS 10 OUTPUT DERATING A153-01-02 COOLING : CONVECTION COOLING Ta(C) -10 ~+50 55 60 MOUNTING A 100 85 70 MOUNTING B 100 85 70 LOAD(%) MOUNTING C 100 85 70 MOUTING D 100 100 70 MOUTING E 100 100 70 OUTPUT DERATING CURVE LOAD(%) 110 100 90 80 70 60 MOUNTING A,B,C MOUNTING D,E 50 40 30 20 10 0 -10 0 10 20 30 40 50 60 70 Ta(C) MOUNTING A MOUNTING B MOUNTING C MOUNTING D MOUNTING E (STANDARD MOUNTING) INPUT CONNECTOR INPUT CONNECTOR INPUT CONNECTOR OUTPUT CONNECTOR COMPONENT SIDE OUTPUT CONNECTOR INPUT CONNECTOR DON'T USE