DENSEI-LAMBDA
ZWS 10
A153-01-01D MODEL ZWS10-3 ZWS10-5 ZWS10-12 ZWS10-15 ZWS10-24
ITEMS
1 Nominal Output Voltage V3.3 5 12 15 24
2 Minimum Output Current A00000
3 Maximum Output Current A2.0 2.0 0.85 0.7 0.45
4 Maximum Peak Output Current (*1) A2.4 2.4 1.02 0.84 0.54
5 Maximum Output Power W6.6 10.0 10.2 10.5 10.8
6 Maximum Peak Output Power (*1) W7.92 12.0 12.24 12.6 12.96
7 Efficiency (Typ) (*2) %62 70 70 71 71
8 Input Voltage Range (*3) -85 - 265VAC (47 - 440Hz) or 110 - 330VDC
9 Input Current(Typ) -0.30A at 100VAC, 0.15A at 200VAC
10 Inrush Current(Typ) -15A at 100VAC, 30A at 200VAC, Ta=25°C, Cold Start
11 Output Voltage Range -
+/
-10%
12 Maximum Ripple & Noise 0 - +60°C mV 120 120 150 150 200
(*10) -10 - 0°C mV 160 160 180 180 200
13 Maximum Line Regulation (*4,10) mV 20 20 48 60 96
14 Maximum Load Regulation (*5,10) mV 40 40 96 120 150
15 Maximum Temperature Drift (*6) mV 60 60 140 180 280
16 Over Current Protection (*7) -125% -
17 Over Voltage Protection (*8) -140% -
18 Hold-up Time (Typ) (*2) -17ms at 100VAC, 10W, Ta=25°C
19 Parallel Operation - -
20 Series Operation (*9) - Possible
21 Operating Temperature (*11) --10°C - +50°C : 100%, +60°C : 70%
22 Operating Humidity - 30 - 90%RH
23 Storage Temperature --30°C - +85°C
24 Storage Humidity - 10 - 95%RH
25 Cooling -Convection Cooling
26 Withstand Voltage - Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Output - FG : 500VAC (100mA) for 1min
27
Isolation Resistance
-
More than 100M
Ω
at 25°C and 70%RH Output - FG 500VDC
28 Vibration -10-55Hz (Sweep 1min) Less than 19.6m/s
X,Y,Z 1h each
29 Shock -Less than 196.1m/s
30 Safety -Approved by UL60950-1,CSA60950-1,EN60950-1. Built to meet DENAN
31 Conducted Noise -Built to meet EN55022-B, FCC-ClassB, VCCI-B
32 Weight (Typ) g 120
33 Size (WxHxD) mm 50 x 21 x 105
=NOTES=
*1. Operating time at peak output is less than
10 seconds. (Duty=0.35)
*2.
At 100VAC and maximum output current , Ta=25°C.
*3.
For cases where conformance to various safety
specs (UL,CSA) are required, to be described
as 100 - 240VAC, 50/60Hz on name plate.
*4.
From 85 - 265VAC and constant load.
*5.
From Min load - Full load (Maximum Power)
and constant input voltage.
*6.
From -10 - +50°C constant input voltage and load.
*7.
Current limiting with automatic recovery.
Avoid to operate over load or dead short for 30 seconds.
*8.
Over voltage clamping by Zener Diode.
*9.
Refer to Instruction Manual.
*10.
Please refer to Fig A for measurement of line
& load regulation and ripple voltage.
*11.
At standard mounting method, Fig B.
SPECIFICATIONS
DENSEI-LAMBD
A
ZWS 10
OUTPUT DERATING
A153-01-02
COOLING : CONVECTION COOLIN
G
Ta(°C) MOUNTING A MOUNTING B MOUNTING C MOUTING D MOUTING E
-10 ~+50 100 100 100 100 100
55 85 85 85 100 100
60 70 70 70 70 70
LOAD(%)
OUTPUT DERATING CURVE
0
10
20
30
40
50
60
70
80
90
100
110
-100 10203040506070
Ta(°C)
LOAD(%)
MOUNTING A,B,C
MOUNTING D,E
COMPONENT
SIDE
OUTPUT
CONNECTOR
INPUT
CONNECTOR
OUTPUT
CONNECTOR
INPUT
CONNECTOR
INPUT
CONNECTOR INPUT
CONNECTOR
MOUNTING A MOUNTING B MOUNTING C MOUNTING D MOUNTING E DON'T USE
(STANDARD MOUNTING)