LM3481
VIN
ISEN
COMP
FB
AGND
UVLO VCC
DR
PGND
FA/SYNC/SD
+
+
VIN = 5V
VOUT = 12V
R7
121 k:
R8
121 k:
CC
82 nF
C8
390 pF
RC
22.6 k:RF2
20 k:
RF1
169 k:
RFA
90.9 k:
RSEN
20 m:
CSEN
1 nF
1 PF
CIN1, CIN2
150 PF
L1
6.8 PH
IOUT = 1.8A
COUT1, COUT2
150 PF
C9 D1
Q1
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
LM3481 / -Q1 High-Efficiency Controller for Boost, SEPIC and Flyback DC-DC Converters
1
1 Features
1 LM3481QMM are Automotive-Grade Products
That are AEC-Q100 Grade 1 Qualified (–40°C to
+125°C Operating Junction Temperature)
10-Lead VSSOP Package
Internal Push-Pull Driver With 1-A Peak Current
Capability
Current Limit and Thermal Shutdown
Frequency Compensation Optimized With a
Capacitor and a Resistor
Internal Softstart
Current Mode Operation
Adjustable Undervoltage Lockout With Hysteresis
Pulse Skipping at Light Loads
Key Specifications
Wide Supply Voltage Range of 2.97 V to 48 V
100-kHz to 1-MHz Adjustable and
Synchronizable Clock Frequency
±1.5% (Over Temperature) Internal Reference
10-µA Shutdown Current (Over Temperature)
Create a Custom Design Using the LM3481 with
the WEBENCH Power Designer
2 Applications
Automotive Start-Stop Applications
Automotive ADAS Driver Information
One Cell/Two Cell Li-ion Battery Powered
Portable Bluetooth Audio Systems
Notebooks, PDAs, Digital Cameras, and Other
Portable Applications
Offline Power Supplies
Set-Top Boxes
Boost for Audio Amplifiers
3 Description
The LM3481 device is a versatile Low-Side N-FET
high-performance controller for switching regulators.
The device is designed for use in Boost, SEPIC and
Flyback converters and topologies requiring a low-
side FET as the primary switch. The LM3481 device
can be operated at very high switching frequencies to
reduce the overall solution size. The switching
frequency of the LM3481 device can be adjusted to
any value between 100kHz and 1MHz by using a
single external resistor or by synchronizing it to an
external clock. Current mode control provides
superior bandwidth and transient response in addition
to cycle-by-cycle current limiting. Current limit can be
programmed with a single external resistor.
The LM3481 device has built-in protection features
such as thermal shutdown, short-circuit protection
and overvoltage protection. Power-saving shutdown
mode reduces the total supply current to 5 µA and
allows power supply sequencing. Internal soft-start
limits the inrush current at start-up. Integrated current
slope compensation simplifies the design and, if
needed for specific applications, can be increased
using a single resistor.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LM3481 VSSOP (10) 3.00 mm × 3.00 mm
LM3481-Q1
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Figure 1. LM3481 Typical 5V to 12V Boost Converter Application
2
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 Handling Ratings: LM3481........................................ 4
6.3 Handling Ratings: LM3481-Q1.................................. 4
6.4 Recommended Operating Ratings............................ 4
6.5 Thermal Information.................................................. 5
6.6 Electrical Characteristics........................................... 5
6.7 Typical Characteristics.............................................. 8
7 Detailed Description............................................ 11
7.1 Overview................................................................. 11
7.2 Functional Block Diagram....................................... 12
7.3 Feature Description................................................. 12
7.4 Device Functional Modes........................................ 18
8 Application and Implementation ........................ 19
8.1 Application Information............................................ 19
8.2 Typical Applications ................................................ 19
9 Power Supply Recommendations...................... 30
10 Layout................................................................... 30
10.1 Layout Guidelines ................................................. 30
10.2 Layout Example .................................................... 31
11 Device and Documentation Support................. 32
11.1 Documentation Support ........................................ 32
11.2 Related Links ........................................................ 32
11.3 Trademarks........................................................... 32
11.4 Electrostatic Discharge Caution............................ 32
11.5 Glossary................................................................ 32
12 Mechanical, Packaging, and Orderable
Information........................................................... 33
4 Revision History
Changes from Revision E (April 2012) to Revision F Page
Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device
Functional Modes,Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
LM3481
VIN
ISEN
COMP
FB
AGND
UVLO VCC
DR
PGND
FA/SYNC/SD
1
2
3
4
56
7
8
9
10
3
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
5 Pin Configuration and Functions
10-Pin
VSSOP Package
Top View
Pin Functions
PIN I/O DESCRIPTION
NO. NAME
1 ISEN A Current sense input pin. Voltage generated across an external sense resistor is fed into this pin.
2 UVLO A Under voltage lockout pin. A resistor divider from VIN to ground is connected to the UVLO pin. The
ratio of these resistances determine the input voltage which allows switching and the hysteresis to
disable switching.
3 COMP A Compensation pin. A resistor and capacitor combination connected to this pin provides
compensation for the control loop.
4 FB A Feedback pin. Inverting input of the error amplifier.
5 AGND G Analog ground pin. Internal bias circuitry reference. Should be connected to PGND at a single
point.
6 FA/SYNC/SD I/A Frequency adjust, synchronization, and shutdown pin. A resistor connected from this pin to ground
sets the oscillator frequency. An external clock signal at this pin will synchronize the controller to
the frequency of the clock. A high level on this pin for 30 µs will turn the device off and the device
will then draw 5 µA from the supply typically.
7 PGND G Power ground pin. External power circuitry reference. Should be connected to AGND at a single
point.
8 DR O Drive pin of the IC. The gate of the external MOSFET should be connected to this pin.
9 VCC O Driver supply voltage pin. A bypass capacitor must be connected from this pin to PGND. See
Driver Supply Capacitor Selection section. Do not bias externally.
10 VIN P Power supply input pin.
4
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Ratings indicates
conditions for which the device is intended to be functional, but does not ensure specific performance limits. For ensured specifications
and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions.
(2) Part is MSL1-260C qualified
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
VIN Pin Voltage –0.4 50 V
FB Pin Voltage –0.4 6 V
FA/SYNC/SD Pin Voltage –0.4 6 V
COMP Pin Voltage –0.4 6 V
UVLO Pin Voltage –0.4 6 V
VCC Pin Voltage –0.4 6.5 V
DR Pin Voltage –0.4 6 V
ISEN Pin Voltage –400 600 mV
Peak Driver Output Current 1 A
Power Dissipation Internally Limited
Junction Temperature 150 °C
Lead Temperature
(only applies to
operating conditions) DGS Package 220 °C
Peak Body
Temperature (2) 260 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.2 Handling Ratings: LM3481 MIN MAX UNIT
Tstg Storage temperature range –65 150 °C
V(ESD) Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins(1) –2000 +2000 V
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins(2) –750 +750
(1) AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Handling Ratings: LM3481-Q1 MIN MAX UNIT
Tstg Storage temperature range –65 150 °C
V(ESD) Electrostatic discharge
Human body model (HBM), per AEC Q100-002(1) –2000 +2000
V
Charged device model (CDM), per
AEC Q100-011
Corner pins (1, 5, 6,
and 10) –750 +750
Other pins –750 +750
6.4 Recommended Operating Ratings MIN MAX UNIT
Supply Voltage 2.97 48 V
Junction Temperature Range –40 125 °C
Switching Frequency Range 100 1 kHz/MHz
5
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.5 Thermal Information
THERMAL METRIC(1) LM3481
UNITVSSOP
10 PINS
RθJA Junction-to-ambient thermal resistance 157.3
°C/W
RθJC(top) Junction-to-case (top) thermal resistance 51.1
RθJB Junction-to-board thermal resistance 76.9
ψJT Junction-to-top characterization parameter 5.0
ψJB Junction-to-board characterization parameter 75.6
RθJC(bot) Junction-to-case (bottom) thermal resistance -
(1) The drive pin voltage, VDR, is equal to the input voltage when input voltage is less than 6 V. VDR is equal to 6 V when the input voltage
is greater than or equal to 6 V.
(2) For this test, the FA/SYNC/SD Pin is pulled to ground using a 40-kresistor.
6.6 Electrical Characteristics
VIN= 12 V, RFA= 40 k, TJ= 25°C, unless otherwise indicated.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VFB Feedback Voltage VCOMP = 1.4 V, 2.97 VIN 48 V 1.275 V
VCOMP = 1.4 V, 2.97 VIN 48 V,
–40°C TJ125°C 1.256 1.294
ΔVLINE Feedback Voltage Line Regulation 2.97 VIN 48 V 0.003 %/V
ΔVLOAD Output Voltage Load Regulation IEAO Source/Sink ±0.5 %/A
VUVLOSEN Undervoltage Lockout Reference
Voltage
VUVLO Ramping Down 1.430 V
VUVLO Ramping Down, –40°C TJ
125°C 1.345 1.517
IUVLO UVLO Source Current Enabled 5 µA
Enabled, –40°C TJ125°C 3 6
VUVLOSD UVLO Shutdown Voltage 0.55 0.7 0.82 V
ICOMP COMP pin Current Sink VFB = 0V 640 µA
VCOMP VFB = 1.275V 1 V
fnom Nominal Switching Frequency RFA = 40 k475 kHz
RFA = 40 k, –40°C TJ125°C 406 550
Vsync-HI Threshold for Synchronization on
FA/SYNC/SD pin Synchronization Voltage Rising 1.4 V
Vsync-LOW Threshold for Synchronization on
FA/SYNC/SD pin Synchronization Voltage Falling 0.7 V
RDS1 (ON) Driver Switch On Resistance (top) IDR = 0.2A, VIN= 5 V 4 Ω
RDS2 (ON) Driver Switch On Resistance (bottom) IDR = 0.2A 2 Ω
VDR (max) Maximum Drive Voltage Swing(1) VIN < 6V VIN V
VIN 6V 6
Dmax Maximum Duty Cycle RFA=40 k81% 85%
tmin (on) Minimum On Time 250 363 ns
worst case over temperature 571 ns
ISUPPLY Supply Current (switching) See(2) 3.7 mA
See(2), –40°C TJ125°C 5.0
6
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Electrical Characteristics (continued)
VIN= 12 V, RFA= 40 k, TJ= 25°C, unless otherwise indicated.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
(3) For this test, the FA/SYNC/SD Pin is pulled to 3 V using a 40-kresistor.
(4) The overvoltage protection is specified with respect to the feedback voltage. This is because the overvoltage protection tracks the
feedback voltage. The overvoltage threshold can be calculated by adding the feedback voltage (VFB) to the overvoltage protection
specification.
(5) The FA/SYNC/SD pin should be pulled to VIN through a resistor to turn the regulator off. The voltage on the FA/SYNC/SD pin must be
above the max limit for the Output = High longer than 30 µs to keep the regulator off and must be below the minimum limit for Output =
Low to keep the regulator on.
IQQuiescent Current in Shutdown Mode
VFA/SYNC/SD = 3 V(3), VIN = 12 V 9
µA
VFA/SYNC/SD = 3 V(3), VIN = 12 V,
–40°C TJ125°C 15
VFA/SYNC/SD = 3 V(3), VIN = 5 V 5
VFA/SYNC/SD = 3 V(3), VIN = 5 V, –40°C
TJ125°C 10
VSENSE Current Sense Threshold Voltage 160 mV
–40°C TJ125°C 100 190
VSC Over Load Current Limit Sense Voltage 220 mV
–40°C TJ125°C 157 275
VSL Internal Compensation Ramp Voltage 90 mV
VOVP Output Over-voltage Protection (with
respect to feedback voltage)(4) VCOMP = 1.4 V 85 mV
VCOMP = 1.4 V, –40°C TJ125°C 26 135
VOVP(HYS) Output Over-Voltage Protection
Hysteresis VCOMP = 1.4 V 70 mV
VCOMP = 1.4 V, –40°C TJ125°C 28 106
Gm Error Amplifier Transconductance VCOMP = 1.4 V 450 µmho
VCOMP = 1.4 V, –40°C TJ125°C 216 690
AVOL Error Amplifier Voltage Gain
VCOMP = 1.4 V, IEAO = 100 µA
(Source/Sink) 60 V/V
VCOMP = 1.4 V, IEAO = 100 µA
(Source/Sink), –40°C TJ125°C 35 66
IEAO Error Amplifier Output Current (Source/
Sink)
Source, VCOMP = 1.4 V, VFB = 1.1 V 640 µA
Source, VCOMP = 1.4 V, VFB = 1.1 V,
–40°C TJ125°C 475 837
Sink, VCOMP = 1.4 V, VFB = 1.4 V 65 µA
Sink, VCOMP = 1.4 V, VFB = 1.4 V,
–40°C TJ125°C 31 100
VEAO Error Amplifier Output Voltage Swing
Upper Limit: VFB = 0 V, COMP Pin
Floating 2.70 V
Upper Limit: VFB = 0 V, COMP Pin
Floating, –40°C TJ125°C 2.45 2.93
Lower Limit: VFB = 1.4 V 0.60 V
Lower Limit: VFB = 1.4 V, –40°C TJ
125°C 0.32 0.90
tSS Internal Soft-Start Delay VFB = 1.2 V, COMP Pin Floating 8.7 15 21.3 ms
trDrive Pin Rise Time Cgs = 3000 pf, VDR = 0 V to 3 V 25 ns
tfDrive Pin Fall Time Cgs = 3000 pf, VDR = 3 V to 0 V 25 ns
VSD Shutdown signal
threshold(5)FA/SYNC/SD pin
Output = High (Shutdown) 1.31 V
Output = High (Shutdown), –40°C
TJ125°C 1.40
Output = Low (Enable) 0.68 V
Output = Low (Enable), –40°C TJ
125°C 0.40
7
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Electrical Characteristics (continued)
VIN= 12 V, RFA= 40 k, TJ= 25°C, unless otherwise indicated.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
ISD Shutdown Pin Current FA/SYNC/SD
pin VSD = 5 V 1µA
VSD = 0 V 20
TSD Thermal Shutdown 165 °C
Tsh Thermal Shutdown Hysteresis 10 °C
8
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
6.7 Typical Characteristics
Unless otherwise specified, VIN = 12 V, TJ= 25°C.
Figure 3. Comp Pin Voltage vs. Load Current Figure 4. Switching Frequency vs. RFA
Figure 5. Efficiency vs. Load Current (3.3 VIN and 12 VOUT)Figure 6. Efficiency vs. Load Current (5 VIN and 12 VOUT)
Figure 7. Efficiency vs. Load Current (9 VIN and 12 VOUT)Figure 8. Frequency vs. Temperature
9
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified, VIN = 12 V, TJ= 25°C.
Figure 9. COMP Pin Source Current vs. Temperature Figure 10. ISupplyvs. Input Voltage (Nonswitching)
Figure 11. ISupply vs. Input Voltage (Switching) Figure 12. Shutdown Threshold Hysteresis vs. Temperature
Figure 13. Drive Voltage vs. Input Voltage Figure 14. Short Circuit Protection vs. VIN
10
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise specified, VIN = 12 V, TJ= 25°C.
Figure 15. Current Sense Threshold vs. Input Voltage Figure 16. Compensation Ramp Amplitude vs. Input Voltage
Figure 17. Minimum On-Time vs. Temperature
PWM
Comparator
Oscillator Sets
the RS Latch
PWM Comparator resets
the RS latch
Blank-Out prevents false
reset
+
_
VSL
Tmin (on) Blank-Out time
11
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
7 Detailed Description
7.1 Overview
The LM3481 device uses a fixed frequency, Pulse Width Modulated (PWM), current mode control architecture. In
a typical application circuit, the peak current through the external MOSFET is sensed through an external sense
resistor. The voltage across this resistor is fed into the ISEN pin. This voltage is then level shifted and fed into the
positive input of the PWM comparator. The output voltage is also sensed through an external feedback resistor
divider network and fed into the error amplifier (EA) negative input (feedback pin, FB). The output of the error
amplifier (COMP pin) is added to the slope compensation ramp and fed into the negative input of the PWM
comparator.
At the start of any switching cycle, the oscillator sets the RS latch using the SET/Blank-out and switch logic
blocks. This forces a high signal on the DR pin (gate of the external MOSFET) and the external MOSFET turns
on. When the voltage on the positive input of the PWM comparator exceeds the negative input, the RS latch is
reset and the external MOSFET turns off.
The voltage sensed across the sense resistor generally contains spurious noise spikes, as shown in Figure 18.
These spikes can force the PWM comparator to reset the RS latch prematurely. To prevent these spikes from
resetting the latch, a blank-out circuit inside the IC prevents the PWM comparator from resetting the latch for a
short duration after the latch is set. This duration, called the blank-out time, is typically 250 ns and is specified as
tmin (on) in the Electrical Characteristics section.
Under extremely light load or no-load conditions, the energy delivered to the output capacitor when the external
MOSFET is on during the blank-out time is more than what is delivered to the load. An overvoltage comparator
inside the LM3481 prevents the output voltage from rising under these conditions by sensing the feedback (FB
pin) voltage and resetting the RS latch. The latch remains in a reset state until the output decays to the nominal
value. Thus the operating frequency decreases at light loads, resulting in excellent efficiency.
Figure 18. Basic Operation of the PWM Comparator
FB
FA/SYNC/SD
COMP
ISEN
AGND PGND
DR
VIN
Shutdown Detect
SYNC/Fixed
Frequency detect
Soft-start
+
EA
+
-
+
Slope
Compensation
Thermal
Shutdown
Set/Blankout
Switch
Logic
Switch
Driver
1.275V
Reference
Oscillator
+
220 mV
Level Shifter
6
+
One Shot
Bias
Voltages
6V
Overvoltage
Comparator
Short-circuit
Comparator
Ramp
Adjust
V-I
Converter
I-V
Converter
PWM
Comparator R S
Q
VCC
UVLO
UVLO
40 éA
Vfb + Vovp -
-
-
-
12
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
7.2 Functional Block Diagram
Figure 19. LM3481 Simplified Functional Block Diagram
7.3 Feature Description
7.3.1 Overvoltage Protection
The LM3481 has overvoltage protection (OVP) for the output voltage. OVP is sensed at the feedback pin (FB). If
at anytime the voltage at the feedback pin rises to VFB + VOVP, OVP is triggered. See the Electrical
Characteristics section for limits on VFB and VOVP.
OVP will cause the drive pin (DR) to go low, forcing the power MOSFET off. With the MOSFET off, the output
voltage will drop. The LM3481 will begin switching again when the feedback voltage reaches VFB + (VOVP -
VOVP(HYS)). See the Electrical Characteristics section for limits on VOVP(HYS). The Error Amplifier is operationnal
during OVP events.
7.3.2 Bias Voltage
The internal bias of the LM3481 comes from either the internal bias voltage generator as shown in the block
diagram or directly from the voltage at the VIN pin. At input voltages lower than 6 V the internal IC bias is the
input voltage and at voltages above 6 V the internal bias voltage generator of the LM3481 provides the bias. The
voltage for the gate driver is output on the VCC pin for compensation by an external capacitor (0.47µF to 4.7µF
depending on the FET requirements). Biasing the VCC pin by an external voltage source should not be
attempted.
<
1
M2
M1
-
'Vsamp1 = - M2
M1
D
1-D 'Vsamp0
'Vsamp0 = -
13
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Feature Description (continued)
7.3.3 Slope Compensation Ramp
The LM3481 uses a current mode control scheme. The main advantages of current mode control are inherent
cycle-by-cycle current limit for the switch and simpler control loop characteristics. It is easy to parallel power
stages using current mode control because current sharing is automatic. However there is a natural instability
that will occur for duty cycles, D, greater than 50% if additional slope compensation is not addressed as
described below.
The current mode control scheme samples the inductor current, IL, and compares the sampled signal, Vsamp, to a
internally generated control signal, Vc. The current sense resistor, RSEN, as shown in Figure 23, converts the
sampled inductor current, IL, to the voltage signal, Vsamp, that is proportional to ILsuch that:
Vsamp = ILx RSEN (1)
The rising and falling slopes, M1and M2respectively, of Vsamp are also proportional to the inductor current rising
and falling slopes, Mon and Moff respectively. Where Mon is the inductor slope during the switch on-time and
Moff is the inductor slope during the switch off-time and are related to M1and M2by:
M1= Mon x RSEN (2)
M2=Moff x RSEN (3)
For the boost topology:
Mon = VIN / L (4)
Moff = (VIN VOUT) / L (5)
M1= [VIN / L] x RSEN (6)
M2= [(VIN VOUT) / L] x RSEN (7)
M2= [(VOUT VIN) / L] x RSEN (8)
Current mode control has an inherent instability for duty cycles greater than 50%, as shown in Figure 20, where
the control signal slope, MC, equals zero. In Figure 20, a small increase in the load current causes the sampled
signal to increase by ΔVsamp0. The effect of this load change, ΔVsamp1, at the end of the first switching cycle is :
(9)
From Equation 9, when D > 0.5, ΔVsamp1 will be greater than ΔVsamp0. In other words, the disturbance is
divergent. So a very small perturbation in the load will cause the disturbance to increase. To ensure that the
perturbed signal converges we must maintain:
(10)
Figure 20. Subharmonic Oscillation for D>0.5
Control Signal
Compensation Ramp
without RSL
-MC
VSL
'VSL
Control Signal
Compensation Ramp
with RSL
<1
M2 - MC
M1 + MC
-
M2 - MC
'Vsamp1 = - M1 + MC
'Vsamp0
+
_
PWM
Comparator
Control Signal
Compensation Ramp
-M2
-MC
DTS(1-D)TS
M1
'Vsamp1
'Vsamp0
Steady State
Signal Vsamp
Perturbed Signal
VSL Control
Signal
Vsamp
14
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Feature Description (continued)
Figure 21. Compensation Ramp Avoids Subharmonic Oscillation
To prevent the subharmonic oscillations, a compensation ramp is added to the control signal, as shown in
Figure 21.
With the compensation ramp, ΔVsamp1 and the convergence criteria are expressed by,
(11)
(12)
The compensation ramp has been added internally in the LM3481. The slope of this compensation ramp has
been selected to satisfy most applications, and it's value depends on the switching frequency. This slope can be
calculated using the formula:
MC= VSL x fS(13)
In Equation 13, VSL is the amplitude of the internal compensation ramp and fSis the controller's switching
frequency. Limits for VSL have been specified in the Electrical Characteristics section.
To provide the user additional flexibility, a patented scheme has been implemented inside the IC to increase the
slope of the compensation ramp externally, if the need arises. Adding a single external resistor, RSL(as shown in
Figure 23) increases the amplitude of the compensation ramp as shown in Figure 22.
Figure 22. Additional Slope Compensation Added Using External Resistor RSL
Where,
ΔVSL = K x RSL (14)
K = 40 µA typically and changes slightly as the switching frequency changes. Figure 24 shows the effect the
current K has on ΔVSLand different values of RSL as the switching frequency changes.
A more general equation for the slope compensation ramp, MC, is shown below to include ΔVSL caused by the
resistor RSL.
MC= (VSL +ΔVSL) x fS(15)
RFA = fS
22 x 103- 5.74
LM3481
DR
ISEN
RSEN
VIN
L1
D1
Q1
COUT
VOUT
RSL
+
CSEN
15
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Feature Description (continued)
It is good design practice to only add as much slope compensation as needed to avoid subharmonic oscillation.
Additional slope compensation minimizes the influence of the sensed current in the control loop. With very large
slope compensation the control loop characteristics are similar to a voltage mode regulator which compares the
error voltage to a saw tooth waveform rather than the inductor current.
Figure 23. Increasing the Slope of the Compensation Ramp
Figure 24. ΔVSL vs RSL
7.3.4 Frequency Adjust, Synchronization, and Shutdown
The switching frequency of the LM3481 can be adjusted between 100 kHz and 1 MHz using a single external
resistor. This resistor must be connected between the FA/SYNC/SD pin and ground, as shown in Figure 25.
Refer to the Typical Characteristics to determine the value of the resistor required for a desired switching
frequency.
Equation 16 can also be used to estimate the frequency adjust resistor.
Where fSis in kHz and RFA in k.
(16)
FA/SYNC/SD >1.3V
10 k:
RFA
MOSFET State
On-Normal Operation
OFF- Shutdown
LM3481
FA/SYNC/SD
Freq. clock
100 kHz to 1 MHz
RFA
LM3481
FA/SYNC/SD
RFA
LM3481
16
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Feature Description (continued)
The LM3481 can be synchronized to an external clock. The external clock must be connected between the
FA/SYNC/SD pin and ground, as shown in Figure 26. The frequency adjust resistor may remain connected while
synchronizing a signal, therefore if there is a loss of signal, the switching frequency will be set by the frequency
adjust resistor.
It is also necessary to have the width of the synchronization pulse wider than the duty cycle of the converter and
to have the synchronization pulse width 300 ns.
The FA/SYNC/SD pin also functions as a shutdown pin. If a high signal (refer to the Electrical Characteristics
section for definition of high signal) appears on the FA/SYNC/SD pin, the LM3481 stops switching and goes into
a low current mode. The total supply current of the IC reduces to 5 µA, typically, under these conditions.
Figure 27 and Figure 28 show an implementation of a shutdown function when operating in frequency adjust
mode and synchronization mode, respectively. In frequency adjust mode, connecting the FA/SYNC/SD pin to
ground forces the clock to run at a certain frequency. Pulling this pin high shuts down the IC. In frequency adjust
or synchronization mode, a high signal for more than 30 µs shuts down the IC.
Figure 25. Frequency Adjust
Figure 26. Frequency Synchronization
Figure 27. Shutdown Operation in Frequency Adjust Mode
UVLO
VIN
R7
R8
IUVLO
VUVLOSEN
-
+
+
-
2
R7 =
§
¨
©
§
¨
©-1
VEN
1.43V
x
R8
R8 =
§
¨
©
§
¨
©1 +1.43V ± VSH
VEN ± 1.43V
IUVLO x
1.43V
FA/SYNC/SD 40 k:
DR
30 Ps
LM3481
17
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Feature Description (continued)
Figure 28. Shutdown Operation in Synchronization Mode
7.3.5 Undervoltage Lockout (UVLO) Pin
The UVLO pin provides user programmable enable and shutdown thresholds. The UVLO pin is compared to an
internal reference of 1.43 V (typical), and a resistor divider programs the enable threshold, VEN. When the IC is
enabled, a 5-μA current is sourced out of the UVLO pin, which effectively causes a hysteresis, and the UVLO
shutdown threshold, VSH, is now lower than the enable threshold. Setting these thresholds requires two resistors
connected from the VIN pin to the UVLO pin and from the UVLO pin to GND (see Figure 29). Select the desired
enable, VEN, and UVLO shutdown, VSH, threshold voltages and use the Equation 17 and Equation 18 to
determine the resistance values:
(17)
(18)
Figure 29. UVLO Pin Resistor Divider
If the system is designed to work over wide input voltages, the voltage at the UVLO pin could exceed the voltage
limit for the UVLO pin. In this case a zener diode can be connected between the UVLO pin and ground to
prevent the UVLO voltage from rising above the maximum value.
If the UVLO pin function is not desired, select R8 and R7 of equal magnitude greater than 100 k. This will allow
VIN to be in control of the UVLO thresholds. The UVLO pin may also be used to implement the enable/disable
function. If a signal pulls the UVLO pin below the 1.43 V (typical) threshold, the converter will be disabled.
7.3.6 Short-Circuit Protection
When the voltage across the sense resistor (measured on the ISEN Pin) exceeds 220 mV, short-circuit current
limit gets activated. A comparator inside the LM3481 reduces the switching frequency by a factor of 8 and
maintains this condition until the short is removed.
18
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
7.4 Device Functional Modes
The device is set to run as soon as the input voltage crosses above the UVLO set point and at a frequency set
according to the FA/SYNC/SD pin pull-down resistor or to run at a frequency set by the waveform applied to the
FA/SYNC/SD pin.
If the FA/SYNC/SD pin is pulled high, the LM3481 enters shut-down mode.
VOUT + VD1 - VQVIN - VQ
1-D
=
LM3481
VIN
ISEN
COMP
FB
AGND
UVLO VCC
DR
PGND
FA/SYNC/SD
+
+
VIN = 5V
VOUT = 12V
R7
121 k:
R8
121 k:
CC
82 nF
C8
390 pF
RC
22.6 k:RF2
20 k:
RF1
169 k:
RFA
90.9 k:
RSEN
20 m:
CSEN
1 nF
1 PF
CIN1, CIN2
150 PF
L1
6.8 PH
IOUT = 1.8A
COUT1, COUT2
150 PF
C9 D1
Q1
19
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM3481 may be operated in either continuous or discontinuous conduction mode. The following applications
are designed for continuous conduction operation. This mode of operation has higher efficiency and lower EMI
characteristics than the discontinuous mode.
8.2 Typical Applications
8.2.1 Boost Converter
Figure 30. Typical High Efficiency Step-Up (Boost) Converter using LM3481
The most common topology for the LM3481 is the boost or step-up topology. The boost converter converts a low
input voltage into a higher output voltage. The basic configuration for a boost regulator is shown in Figure 31. In
continuous conduction mode (when the inductor current never reaches zero at steady state), the boost regulator
operates in two cycles. In the first cycle of operation, MOSFET Q is turned on and energy is stored in the
inductor. During this cycle, diode D1 is reverse biased and load current is supplied by the output capacitor, COUT.
In the second cycle, MOSFET Q is off and the diode is forward biased. The energy stored in the inductor is
transferred to the load and output capacitor. The ratio of these two cycles determines the output voltage. The
output voltage is defined as:
(19)
(ignoring the voltage drop across the MOSFET and the diode), or
(20)
where D is the duty cycle of the switch, VD1 is the forward voltage drop of the diode, and VQis the drop across
the MOSFET when it is on. The following sections describe selection of components for a boost converter.
+ +
PWM
VOUT
VIN
+
VIN
-+
L
L
RLOAD
+
-
VOUT
+
VIN
-+
L
RLOAD
+
-
VOUT
D1
D1
COUT
COUT
Q
COUT
20
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
A. First Cycle of Operation
B. Second Cycle of Operation
Figure 31. Simplified Boost Converter Diagram
8.2.1.1 Design Requirements
To properly size the components for the application, the designer needs the following parameters: Input voltage
range, output voltage, output current range and required switching frequency. These four main parameters will
affect the choices of component available to achieve a proper system behavior.
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Custom Design with WEBENCH Tools
Click here to create a custom design using the LM3481 device with the WEBENCH®Power Designer.
1. Start by entering your VIN, VOUT and IOUT requirements.
2. Optimize your design for key parameters like efficiency, footprint and cost using the optimizer dial and
compare this design with other possible solutions from Texas Instruments.
3. WEBENCH Power Designer provides you with a customized schematic along with a list of materials with real
time pricing and component availability.
4. In most cases, you will also be able to:
Run electrical simulations to see important waveforms and circuit performance,
Run thermal simulations to understand the thermal performance of your board,
Export your customized schematic and layout into popular CAD formats,
Print PDF reports for the design, and share your design with colleagues.
5. Get more information about WEBENCH tools at www.ti.com/webench.
8.2.1.2.2 Power Inductor Selection
The inductor is one of the two energy storage elements in a boost converter. Figure 32 shows how the inductor
current varies during a switching cycle. The current through an inductor is quantified as:
(21)
=
'iLDVIN
2LfS
IL =IOUT
1-D
t (s)
t (s)
IL_AVG
ISW_AVG
D*Ts Ts
D*Ts Ts
IL (A)
ID (A) (a)
(b)
t (s)
D*Ts Ts
ISW (A)
(c)
ID_AVG
= IOUT_AVG
L
-VOUT
VIN
L
VIN
L
-VOUT
VIN
L
VIN
L
i'
21
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
Figure 32. (a) Inductor Current (b) Diode Current (c) Switch Current
If VL(t) is constant, diL(t)/dt must be constant. Hence, for a given input voltage and output voltage, the current in
the inductor changes at a constant rate.
The important quantities in determining a proper inductance value are IL(the average inductor current) and ΔiL
(the inductor current ripple difference between the peak inductor current and the average inductor current). If ΔiL
is larger than IL, the inductor current drops to zero for a portion of the cycle and the converter operates in
discontinuous conduction mode. If ΔiLis smaller than IL, the inductor current stays above zero and the converter
operates in continuous conduction mode. All the analysis in this data sheet assumes operation in continuous
conduction mode. To operate in continuous conduction mode, the following conditions must be met:
IL>ΔiL(22)
(23)
(24)
Choose the minimum IOUT to determine the minimum L. A common choice is to set (2 x ΔiL) to 30% of IL.
Choosing an appropriate core size for the inductor involves calculating the average and peak currents expected
through the inductor. In a boost converter,
(25)
IL_peak = IL(max) + ΔiL(max) (26)
(27)
DR
VOUT
FB
L
D1
Q
ISEN
COUT
RF2
VIN
LM3481
RSEN
RF1
+
RSEN = VSENSE - (D x VSL)
IOUT(max)
(1-D) +(D x VIN)
(2 x fS x L)
Isw(peak) = IOUT(max)
(1-D) +(D x VIN)
(2 x fS x L)
VOUT = 1.275 (1+ RF1
RF2)
22
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
A core size with ratings higher than these values should be chosen. If the core is not properly rated, saturation
will dramatically reduce overall efficiency.
The LM3481 can be set to switch at very high frequencies. When the switching frequency is high, the converter
can operate with very small inductor values. With a small inductor value, the peak inductor current can be
extremely higher than the output currents, especially under light load conditions.
The LM3481 senses the peak current through the switch. The peak current through the switch is the same as the
peak current calculated above.
8.2.1.2.3 Programming the Output Voltage and Output Current
The output voltage can be programmed using a resistor divider between the output and the feedback pins, as
shown in Figure 33. The resistors are selected such that the voltage at the feedback pin is 1.275 V. RF1 and RF2
can be selected using the equation,
(28)
A 100-pF capacitor may be connected between the feedback and ground pins to reduce noise.
The maximum amount of current that can be delivered at the output can be controlled by the sense resistor,
RSEN. Current limit occurs when the voltage that is generated across the sense resistor equals the current sense
threshold voltage, VSENSE. Limits for VSENSE have been specified in the Electrical Characteristics section. This can
be expressed as:
Isw(peak) x RSEN = VSENSE- D x VSL (29)
The peak current through the switch is equal to the peak inductor current.
Isw(peak) = IL(max) + ΔiL(30)
Therefore for a boost converter,
(31)
Combining the two equations yields an expression for RSEN,
(32)
Evaluate RSEN at the maximum and minimum VIN values and choose the smallest RSEN calculated.
Figure 33. Adjusting the Output Voltage
VIN(MIN)
VOUT
1-
DMAX =
IOUT(max) 2DMAXRDS(ON)
PCOND(MAX) =1 - DMAX
RSEN = IOUT(max)
(1-D) +(D x VIN)
(2 x fS x L)
VSENSE - D x (VSL+'VSL)
23
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
8.2.1.2.4 Current Limit With Additional Slope Compensation
If an external slope compensation resistor is used (see Figure 23) the internal control signal will be modified and
this will have an effect on the current limit.
If RSL is used, then this will add to the existing slope compensation. The command voltage, VCS, will then be
given by:
VCS = VSENSE D x (VSL +ΔVSL) (33)
Where VSENSE is a defined parameter in the Electrical Characteristics section and ΔVSL is the additional slope
compensation generated as discussed in the Slope Compensation Ramp section. This changes the equation for
RSEN to:
(34)
Note that because ΔVSL = RSL x K as defined earlier, RSLcan be used to provide an additional method for setting
the current limit. In some designs RSL can also be used to help filter noise to keep the ISEN pin quiet.
8.2.1.2.5 Power Diode Selection
Observation of the boost converter circuit shows that the average current through the diode is the average load
current, and the peak current through the diode is the peak current through the inductor. The diode should be
rated to handle more than the inductor peak current. The peak diode current can be calculated using the formula:
ID(Peak) = [IOUT/ (1D)] + ΔiL(35)
In Equation 35, IOUT is the output current and ΔiLhas been defined in Figure 32.
The peak reverse voltage for a boost converter is equal to the regulator output voltage. The diode must be
capable of handling this peak reverse voltage. To improve efficiency, a low forward drop Schottky diode is
recommended.
8.2.1.2.6 Power MOSFET Selection
The drive pin, DR, of the LM3481 must be connected to the gate of an external MOSFET. In a boost topology,
the drain of the external N-Channel MOSFET is connected to the inductor and the source is connected to the
ground. The drive pin voltage, VDR, depends on the input voltage (see Typical Characteristics). In most
applications, a logic level MOSFET can be used. For very low input voltages, a sub-logic level MOSFET should
be used.
The selected MOSFET directly controls the efficiency. The critical parameters for selection of a MOSFET are:
Minimum threshold voltage, VTH(MIN)
On-resistance, RDS(ON)
Total gate charge, Qg
Reverse transfer capacitance, CRSS
Maximum drain to source voltage, VDS(MAX)
The off-state voltage of the MOSFET is approximately equal to the output voltage. VDS(MAX) of the MOSFET must
be greater than the output voltage. The power losses in the MOSFET can be categorized into conduction losses
and ac switching or transition losses. RDS(ON) is needed to estimate the conduction losses. The conduction loss,
PCOND, is the I2R loss across the MOSFET. The maximum conduction loss is given by:
(36)
where DMAX is the maximum duty cycle.
(37)
At high switching frequencies the switching losses may be the largest portion of the total losses.
=
'iLDVIN
2LfS
VIN VIN
RIN
CIN
CBYPASS
LM3481
ICIN(RMS) ='iL/3(VOUT - VIN)VIN
=VOUTLfS
12
RGate
tLH = VDR - Vgsth
Qgs
2
Qgd + x
PSW = ILmax x Vout
2x fSW x (tLH + tHL)
24
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
The switching losses are very difficult to calculate due to changing parasitics of a given MOSFET in operation.
Often, the individual MOSFET datasheet does not give enough information to yield a useful result. Equation 38
and Equation 39 give a rough idea how the switching losses are calculated:
(38)
(39)
8.2.1.2.7 Input Capacitor Selection
Due to the presence of an inductor at the input of a boost converter, the input current waveform is continuous
and triangular, as shown in Figure 32. The inductor ensures that the input capacitor sees fairly low ripple
currents. However, as the input capacitor gets smaller, the input ripple goes up. The rms current in the input
capacitor is given by:
(40)
The input capacitor should be capable of handling the rms current. Although the input capacitor is not as critical
in a boost application, low values can cause impedance interactions. Therefore a good quality capacitor should
be chosen in the range of 100 µF to 200 µF. If a value lower than 100 µF is used, then problems with impedance
interactions or switching noise can affect the LM3481. To improve performance, especially with VIN below 8 V, it
is recommended to use a 20resistor at the input to provide a RC filter. This resistor is placed in series with the
VIN pin with only a bypass capacitor attached to the VIN pin directly (see Figure 34). A 0.1-µF or 1-µF ceramic
capacitor is necessary in this configuration. The bulk input capacitor and inductor will connect on the other side
of the resistor with the input power supply.
Figure 34. Reducing IC Input Noise
8.2.1.2.8 Output Capacitor Selection
The output capacitor in a boost converter provides all the output current when the inductor is charging. As a
result it sees very large ripple currents. The output capacitor should be capable of handling the maximum rms
current. The rms current in the output capacitor is:
(41)
Where
(42)
and D, the duty cycle is equal to (VOUT VIN)/VOUT.
The ESR and ESL of the output capacitor directly control the output ripple. Use capacitors with low ESR and ESL
at the output for high efficiency and low ripple voltage. Surface mount tantalums, surface mount polymer
electrolytic and polymer tantalum, Sanyo- OSCON, or multi-layer ceramic capacitors are recommended at the
output.
8.2.1.2.9 Driver Supply Capacitor Selection
A good quality ceramic bypass capacitor must be connected from the VCC pin to the PGND pin for proper
operation. This capacitor supplies the transient current required by the internal MOSFET driver, as well as
filtering the internal supply voltage for the controller. A value of between 0.47 µF and 4.7 µF is recommended.
25
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
8.2.1.2.10 Compensation
For detailed explanation on how to select the right compensation components to attach to the compensation pin
for a boost topology please see AN-1286 Compensation for the LM3478 Boost Controller (SNVA067). When
calculating the Error Amplifier DC gain, AEA, ROUT = 152 kfor the LM3481.
8.2.1.3 Application Curve
Figure 35. Start-Up Pattern for a 5-Vin, 12-Vout Boost Converter Using LM3481 Boost Evaluation Module
(C1: Inductor Current, C2: Vin, C3:Vout)
LM3481
VIN
ISEN
COMP
FB
AGND
UVLO VCC
DR
PGND
FA/SYNC/SD
+
+
VIN = 3.0V to 24V
VOUT = 5V, 1A
CIN
15 PF, 35V x2
COUT
100 PF, 10V
1 PF, ceramic
RSEN
0.05:
L1
10 PH
L2
10 PH
0.47 µFMBRS130LT3
RFA
40 k:
CSEN
1 nF
Q1
IRF7807
CS
RC
4.7 k:
CC
0.1 PF
RF1
60 k:
RF2
20 k:
R7
10 k:
D2
5.1V
D1
26
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
8.2.2 Typical SEPIC Converter
Figure 36. Typical SEPIC Converter using LM3481
Because the LM3481 controls a low-side N-Channel MOSFET, it can also be used in SEPIC (Single Ended
Primary Inductance Converter) applications. An example of SEPIC using the LM3481 is shown in Figure 36. As
shown in Figure 36, the output voltage can be higher or lower than the input voltage. The SEPIC uses two
inductors to step-up or step-down the input voltage. The inductors L1 and L2 can be two discrete inductors or
two windings of a coupled transformer because equal voltages are applied across the inductor throughout the
switching cycle. Using two discrete inductors allows use of catalog magnetics, as opposed to a custom
transformer. The input ripple can be reduced along with size by using the coupled windings of transformer for L1
and L2.
Due to the presence of the inductor L1 at the input, the SEPIC inherits all the benefits of a boost converter. One
main advantage of SEPIC over a boost converter is the inherent input to output isolation. The capacitor CS
isolates the input from the output and provides protection against shorted or malfunctioning load. Hence, the
SEPIC is useful for replacing boost circuits when true shutdown is required. This means that the output voltage
falls to 0V when the switch is turned off. In a boost converter, the output can only fall to the input voltage minus a
diode drop.
The duty cycle of a SEPIC is given by:
(43)
In Equation 43, VQis the on-state voltage of the MOSFET, Q1, and VDIODE is the forward voltage drop of the
diode.
8.2.2.1 Design Requirements
To properly size the components for the application, the designer needs the following parameters: Input voltage
range, output voltage, output current range and required switching frequency. These four main parameters will
affect the choices of component available to achieve a proper system behavior.
8.2.2.2 Detailed Design Procedure
8.2.2.2.1 Power MOSFET Selection
As in a boost converter, the parameters governing the selection of the MOSFET are the minimum threshold
voltage, VTH(MIN), the on-resistance, RDS(ON), the total gate charge, Qg, the reverse transfer capacitance, CRSS,
and the maximum drain to source voltage, VDS(MAX). The peak switch voltage in a SEPIC is given by:
VSW(PEAK) = VIN + VOUT + VDIODE (44)
The selected MOSFET should satisfy the condition:
VDS(MAX) > VSW(PEAK) (45)
2
'VOUT = IOUT
1-D +
'IL2
( ) ESR
L2 > (VIN - VQ)D
2IOUTfS
L1 > (VIN - VQ)(1-D)
2IOUTfS
ISWPEAK = IL1(AVG) + IOUT +'IL1 + 'IL2
2
27
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
The peak switch current is given by:
(46)
Where ΔIL1 and ΔIL2 are the peak-to-peak inductor ripple currents of inductors L1 and L2 respectively.
The rms current through the switch is given by:
(47)
8.2.2.2.2 Power Diode Selection
The Power diode must be selected to handle the peak current and the peak reverse voltage. In a SEPIC, the
diode peak current is the same as the switch peak current. The off-state voltage or peak reverse voltage of the
diode is VIN + VOUT. Similar to the boost converter, the average diode current is equal to the output current.
Schottky diodes are recommended.
8.2.2.2.3 Selection of Inductors L1 and L2
Proper selection of the inductors L1 and L2 to maintain constant current mode requires calculations of the
following parameters.
Average current in the inductors:
(48)
IL2AVE = IOUT (49)
Peak-to-peak ripple current, to calculate core loss if necessary:
(50)
(51)
Maintaining the condition IL>ΔIL/2 to ensure continuous conduction mode yields the following minimum values
for L1 and L2:
(52)
(53)
Peak current in the inductor, to ensure the inductor does not saturate:
(54)
(55)
IL1PK must be lower than the maximum current rating set by the current sense resistor.
The value of L1 can be increased above the minimum recommended value to reduce input ripple and output
ripple. However, once ΔIL1 is less than 20% of IL1AVE, the benefit to output ripple is minimal.
By increasing the value of L2 above the minimum recommendation, ΔIL2 can be reduced, which in turn will
reduce the output ripple voltage:
(56)
where ESR is the effective series resistance of the output capacitor.
ICIN(RMS) ='IL1/12 VIN - VQ
(L1)fS
D
3
2
=
CS tL1 IOUT2
(VIN - VQ)2
'IL1 =(VIN - VQ) D
(L1)fS
CS'VS2 = (L1)'IL12
1
21
2
ISWPEAK
VSENSE - D x (VSL+'VSL)
RSEN =
28
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
If L1 and L2 are wound on the same core, then L1 = L2 = L. All the equations above will hold true if the
inductance is replaced by 2L. A good choice for transformer with equal turns is Coiltronics CTX series Octopack.
8.2.2.2.4 Sense Resistor Selection
The peak current through the switch, ISWPEAK, can be adjusted using the current sense resistor, RSEN, to provide
a certain output current. Resistor RSEN can be selected using the formula:
(57)
8.2.2.2.5 SEPIC Capacitor Selection
The selection of SEPIC capacitor, CS, depends on the rms current. The rms current of the SEPIC capacitor is
given by:
(58)
The SEPIC capacitor must be rated for a large ACrms current relative to the output power. This property makes
the SEPIC much better suited to lower power applications where the rms current through the capacitor is small
(relative to capacitor technology). The voltage rating of the SEPIC capacitor must be greater than the maximum
input voltage. Tantalum capacitors are the best choice for SMT, having high rms current ratings relative to size.
Ceramic capacitors could be used, but the low C values will tend to cause larger changes in voltage across the
capacitor due to the large currents, and high C value ceramics are expensive. Electrolytics work well for through
hole applications where the size required to meet the rms current rating can be accommodated. There is an
energy balance between CSand L1, which can be used to determine the value of the capacitor. The basic
energy balance equation is:
(59)
Where
(60)
is the ripple voltage across the SEPIC capacitor, and
(61)
is the ripple current through the inductor L1. The energy balance equation can be solved to provide a minimum
value for CS:
(62)
8.2.2.2.6 Input Capacitor Selection
Similar to a boost converter, the SEPIC has an inductor at the input. Hence, the input current waveform is
continuous and triangular. The inductor ensures that the input capacitor sees fairly low ripple currents. However,
as the input capacitor gets smaller, the input ripple goes up. The rms current in the input capacitor is given by:
(63)
The input capacitor should be capable of handling the rms current. Although the input capacitor is not as critical
in a SEPIC application, low values can cause impedance interactions. Therefore a good quality capacitor should
be chosen in the range of 100 µF to 200 µF. If a value lower than 100 µF is used, then problems with impedance
interactions or switching noise can affect the LM3481. To improve performance, especially with VIN below 8 V, it
is recommended to use a 20resistor at the input to provide a RC filter. This resistor is placed in series with the
VIN pin with only a bypass capacitor attached to the VIN pin directly (see Figure 34). A 0.1 µF or 1 µF ceramic
capacitor is necessary in this configuration. The bulk input capacitor and inductor will connect on the other side
of the resistor with the input power supply.
IRMS = ISWPEAK2 - ISWPEAK ('IL1 + 'IL2) +('IL1 + 'IL2)2
3(1-D) - IOUT2
29
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
Typical Applications (continued)
8.2.2.2.7 Output Capacitor Selection
The output capacitor of the SEPIC sees very large ripple currents similar to the output capacitor of a boost
converter. The rms current through the output capacitor is given by:
(64)
The ESR and ESL of the output capacitor directly control the output ripple. Use capacitors with low ESR and ESL
at the output for high efficiency and low ripple voltage. Surface mount tantalums, surface mount polymer
electrolytic and polymer tantalum, Sanyo- OSCON, or multi-layer ceramic capacitors are recommended at the
output for low ripple.
8.2.2.3 Application Curve
Figure 37. Start-Up Pattern for a 5-Vin, 12-Vout SEPIC Converter on LM3481 SEPIC Evaluation Module
(C2: Vin, C3:Vout)
30
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
9 Power Supply Recommendations
The LM3481 is designed to operate from various DC power supply including a car battery. If so, VIN input should
be protected from reversal voltage and voltage dump over 48 Volts. The impedance of the input supply rail
should be low enough that the input current transient does not cause drop below VIN UVLO level. If the input
supply is connected by using long wires, additional bulk capacitance may be required in addition to normal input
capacitor.
10 Layout
10.1 Layout Guidelines
Good board layout is critical for switching controllers such as the LM3481. First the ground plane area must be
sufficient for thermal dissipation purposes and second, appropriate guidelines must be followed to reduce the
effects of switching noise. Switch mode converters are very fast switching devices. In such devices, the rapid
increase of input current combined with the parasitic trace inductance generates unwanted Ldi/dt noise spikes.
The magnitude of this noise tends to increase as the output current increases. This parasitic spike noise may
turn into electromagnetic interference (EMI), and can also cause problems in device performance. Therefore,
care must be taken in layout to minimize the effect of this switching noise. The current sensing circuit in current
mode devices can be easily effected by switching noise. This noise can cause duty cycle jitter which leads to
increased spectral noise. Although the LM3481 has 250 ns blanking time at the beginning of every cycle to
ignore this noise, some noise may remain after the blanking time.
The most important layout rule is to keep the AC current loops as small as possible. Figure 38 shows the current
flow of a boost converter. The top schematic shows a dotted line which represents the current flow during on-
state and the middle schematic shows the current flow during off-state. The bottom schematic shows the currents
we refer to as AC currents. These currents are the most critical currents because current is changing in very
short time periods. The dotted lined traces of the bottom schematic are the once to make as short as possible.
Figure 38. Current Flow in a Boost Application
The PGND and AGND pins have to be connected to the same ground very close to the IC. To avoid ground loop
currents attach all the grounds of the system only at one point.
A ceramic input capacitor should be connected as close as possible to the Vin pin and grounded close to the
GND pin.
For a layout example please see AN-2094 LM3481 SEPIC Evaluation Board (SNVA461). For more information
about layout in switch mode power supplies refer to AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines
(SNVA054).
Rsense
GND IN+OUT+
FB
COMP
UVLO
Isense
FA LM3481
31
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
10.2 Layout Example
Figure 39. Typical Layout for a Boost Converter
32
LM3481
,
LM3481-Q1
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
www.ti.com
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation Feedback Copyright © 2007–2014, Texas Instruments Incorporated
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Custom Design with WEBENCH Tools
Click here to create a custom design using the LM3481 device with the WEBENCH®Power Designer.
1. Start by entering your VIN, VOUT and IOUT requirements.
2. Optimize your design for key parameters like efficiency, footprint and cost using the optimizer dial and
compare this design with other possible solutions from Texas Instruments.
3. WEBENCH Power Designer provides you with a customized schematic along with a list of materials with real
time pricing and component availability.
4. In most cases, you will also be able to:
Run electrical simulations to see important waveforms and circuit performance,
Run thermal simulations to understand the thermal performance of your board,
Export your customized schematic and layout into popular CAD formats,
Print PDF reports for the design, and share your design with colleagues.
5. Get more information about WEBENCH tools at www.ti.com/webench.
11.1.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.1.3 Related Documentation
AN-1286 Compensation for the LM3478 Boost Controller (SNVA067)
AN-2094 LM3481 SEPIC Evaluation Board (SNVA461)
AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines (SNVA054)
SNVU111 330mW AC or DC Tiny Flyback Converter Power Supply (SNVU111)
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL
DOCUMENTS TOOLS &
SOFTWARE SUPPORT &
COMMUNITY
LM3481 Click here Click here Click here Click here Click here
LM3481-Q1 Click here Click here Click here Click here Click here
11.3 Trademarks
WEBENCH is a registered trademark of Texas Instruments.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
33
LM3481
,
LM3481-Q1
www.ti.com
SNVS346F NOVEMBER 2007REVISED NOVEMBER 2014
Product Folder Links: LM3481 LM3481-Q1
Submit Documentation FeedbackCopyright © 2007–2014, Texas Instruments Incorporated
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
PACKAGE OPTION ADDENDUM
www.ti.com 2-May-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM3481MM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SJPB
LM3481MMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SJPB
LM3481QMM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SUAB
LM3481QMMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS
& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 SUAB
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 2-May-2020
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM3481, LM3481-Q1 :
Catalog: LM3481
Automotive: LM3481-Q1
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM3481MM/NOPB VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM3481MMX/NOPB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM3481QMM/NOPB VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM3481QMMX/NOPB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Aug-2017
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM3481MM/NOPB VSSOP DGS 10 1000 210.0 185.0 35.0
LM3481MMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0
LM3481QMM/NOPB VSSOP DGS 10 1000 210.0 185.0 35.0
LM3481QMMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Aug-2017
Pack Materials-Page 2
www.ti.com
PACKAGE OUTLINE
C
TYP
5.05
4.75
1.1 MAX
8X 0.5
10X 0.27
0.17
2X
2
0.15
0.05
TYP
0.23
0.13
0 - 8
0.25
GAGE PLANE
0.7
0.4
A
NOTE 3
3.1
2.9
B
NOTE 4
3.1
2.9
4221984/A 05/2015
VSSOP - 1.1 mm max heightDGS0010A
SMALL OUTLINE PACKAGE
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-187, variation BA.
110
0.1 C A B
6
5
PIN 1 ID
AREA
SEATING PLANE
0.1 C
SEE DETAIL A
DETAIL A
TYPICAL
SCALE 3.200
www.ti.com
EXAMPLE BOARD LAYOUT
(4.4)
0.05 MAX
ALL AROUND 0.05 MIN
ALL AROUND
10X (1.45)
10X (0.3)
8X (0.5)
(R )
TYP
0.05
4221984/A 05/2015
VSSOP - 1.1 mm max heightDGS0010A
SMALL OUTLINE PACKAGE
SYMM
SYMM
LAND PATTERN EXAMPLE
SCALE:10X
1
56
10
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
www.ti.com
EXAMPLE STENCIL DESIGN
(4.4)
8X (0.5)
10X (0.3)
10X (1.45)
(R ) TYP0.05
4221984/A 05/2015
VSSOP - 1.1 mm max heightDGS0010A
SMALL OUTLINE PACKAGE
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
SYMM
SYMM
1
56
10
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:10X
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated