CML Microcircuits
COMMUNICATION SEMICONDUCTORS
CMX589A
GMSK Modem
2002 CML Microsystems Plc
D/589A/4 April 2002
Features and Applications
Data Rates from 4kbps to 200kbps
Full or Half Duplex Gaussian Filter and Data
Recovery for Minimum Shift Keying (GMSK)
Designs
Selectable BT: (0.3 or 0.5)
Low Power
3.0V, 20kbps, 1.5mA typ.
5.0V, 64kbps, 4.0mA typ.
Low Current Non-DSP Solution
Small TSSOP Packs fit PCMCIA/PC Cards
Portable Wireless Data Applications
Cellular Digital Packet Data (CDPD)
Mobitex Mobile Data System
Spread Spectrum Data Links
GPS/Differential GPS Wireless Links
Point-of-Sale Terminals
Low Power Wireless Data Link for PCs,
Laptops, and Printers
Brief Description
The CMX589A is a single-chip synchronous data pump/modem designed for Wireless Data Applications.
Employing Gaussian filtering for Minimum shift Keying (GMSK) baseband modulation applications, the
CMX589A features a wide range of available data rates from 4k to 200k bps. Data Rates and the choice of
BT (0.3 or 0.5) are pin programmable to provide for different system requirements.
The Tx and Rx digital data interfaces are bit serial, synchronized to generated Tx and Rx data clocks.
Separate Tx and Rx Powersave inputs allow full or half-duplex operation. Rx input levels can be set by
suitable AC and DC level adjusting circuitry built with external components around an on-chip Rx Input
Amplifier.
Acquisition, Lock, and Hold of Rx data signals are made easier and faster by the use of Rx Control Inputs
to clamp, detect, and /or hold input data levels and can be set by the µProcessor as required. The Rx S/N
output provides an indication of the quality of the received signal.
The CMX589A may be used with a 3.0V to 5.5V power supply and is available in the following packages:
24-pin TSSOP (CMX589AE2), 24-pin SSOP (CMX589AD5), 24-pin SOIC (CMX589AD2), and 24-pin PDIP
(CMX589AP4).
GMSK Modem CMX589A
2002 CML Microsystems Plc 2 D/589A/4
Contents
Section Page
Features and Applications .................................................................................................1
Brief Description.................................................................................................................1
Block Diagram.....................................................................................................................3
2 Signal List.........................................................................................................................4
3 External Components......................................................................................................6
4 General Description.........................................................................................................8
4.1 Clock Oscillator Divider.........................................................................................................8
4.2 Receive.................................................................................................................................8
4.2.1 Rx Signal Path Description.....................................................................................................8
4.2.2 Rx Circuit Control Modes .......................................................................................................9
4.2.3 Rx Clock Extraction..............................................................................................................10
4.2.4 Rx Data Extraction...............................................................................................................10
4.2.6 Rx Signal Quality.................................................................................................................12
4.3 Transmit..............................................................................................................................12
4.3.1 Tx Signal Path Description...................................................................................................12
4.4 Data Formats......................................................................................................................14
4.5 Acquisition and Hold Modes...............................................................................................14
5 Application......................................................................................................................15
5.1 Radio Channel Requirements.............................................................................................15
5.1.1 Bit Rate, BT, and Bandwidth ................................................................................................15
5.1.2 FM Modulator, Demodulator and IF......................................................................................15
5.1.3 Two-Point Modulation...........................................................................................................16
5.2 AC Coupling of Tx and Rx Signals .....................................................................................17
6 Performance Specifications..........................................................................................18
6.1 Electrical Specifications......................................................................................................18
6.1.1 Absolute Maximum Limits....................................................................................................18
6.1.2 Operating Limits...................................................................................................................19
6.1.3 Operating Characteristics.....................................................................................................20
6.2 Packages............................................................................................................................22
GMSK Modem CMX589A
2002 CML Microsystems Plc 3 D/589A/4
Block Diagram
Figure 1: Block Diagram
Figure 2: System Block Diagram
GMSK Modem CMX589A
2002 CML Microsystems Plc 4 D/589A/4
2 Signal List
Pin No.
E2/D5/
D2/P4
Signal Type Description
1 XTALN O/P The output of the on-chip clock oscillator.
2 XTAL/CLOCK I/P The input to the on-chip Xtal oscillator. A Xtal, or externally derived
clock (fXTAL) pulse input should be connected here. If an externally
generated clock is to be used, it should be connected to this pin and the
XTALN pin left unconnected. Note: Operation without a suitable Xtal or
clock input may cause device damage.
3 ClkDivA I/P Logic level inputs control the internal clock divider and therefore the
transmit and receive data rate. See Table 4.
4 ClkDivB I/P Logic level inputs control the internal clock divider and therefore the
transmit and receive data rate. See Table 4.
5 RxHOLDN I/P A logic ‘0’ applied to this input will freeze the Clock Extraction and Level
Measurement circuits unless they are in ‘Acquire’ mode.
6 RxDCacq I/P A logic ‘1’ applied to this input will set the Rx Level Measurement
circuitry to the ‘Acquire’ mode. See Table 6.
7 PLLacq I/P A logic ‘1’ applied to this input will set the Rx Clock Extraction circuitry
to the ‘Acquire’ mode. See Table 5.
8 Rx PSAVE I/P A logic ‘1’ applied to this input will powersave all receive circuits except
for Rx CLK output (which will continue at the set bit-rate) and cause the
Rx Data and Rx S/N outputs to go to a logic ‘0’.
9 VBIAS power The internal circuitry bias line, held at VDD/2. This pin must be
bypassed to VSS by a capacitor mounted close to the pin.
10 Rx FB O/P Output of the Rx Input Amplifier.
11 Rx Signal In I/P Input to Rx input amplifier.
12 VSS power Negative supply (GND).
13 DOC1 O/P Connections to the Rx Level Measurement Circuitry. A capacitor should
be connected from this pin to VSS.
14 DOC2 O/P Connections to the Rx Level Measurement Circuitry. A capacitor should
be connected from this pin to VSS.
15 BT I/P A logic level to select the modem BT (the ratio of the Tx Filter's -3dB
frequency to the Bit-Rate). A logic ‘1’ = BT of 0.5 and a logic ‘0’ = BT of
0.3.
GMSK Modem CMX589A
2002 CML Microsystems Plc 5 D/589A/4
Pin No.
E2/D5/
D2/P4
Signal Type Description
16 Tx Out O/P Gaussian filtered Tx output signal. In powersave mode the Tx Out pin
is high impedance.
17 Tx Enable I/P A logic ‘1’ applied to this input, enables the transmit data path, through
the Tx Filter to the Tx Out pin. A logic ‘0’ will place the Tx Out pin to
VBIAS via a high impedance.
18 Tx PSAVE I/P A logic ‘1’ applied to this input will powersave all transmit circuits except
for the Tx Clock.
19 Tx Data I/P The logic level input for the data to be transmitted. This data should be
synchronous with Tx CLK.
20 Rx Data O/P A logic level output carrying the received data, synchronous with
Rx CLK.
21 Rx CLK O/P A logic level clock output at the received data bit-rate.
22 Tx CLK O/P A logic level clock output at the transmit data bit-rate.
23 Rx S/N O/P A logic level output which may be used as an indication of the quality of
the received signal.
24 VDD power Positive supply. Levels and voltages within the device are dependent
upon this supply. This pin should be bypassed to VSS by a capacitor
mounted close to the pin.
Table 1: Signal List
GMSK Modem CMX589A
2002 CML Microsystems Plc 6 D/589A/4
3 External Components
Figure 3: Recommended External Components
Component Notes Value Tolerance Component Notes Value Tolerance
R1 1 ±5% C4 0.1µF ±20%
R2 1.0M ±10% C5 1.0µF ±20%
R3 2 ±10% C6 5 ±20%
R4 3 ±10% C7 6
C1 1 ±10% C8 6
C2 4 C9 7
C3 4 X1 8
Table 2: Recommended External Components
Recommended External Component Notes:
1. The RC network formed by R1 and C1 is required between the Tx Out pin and the input to the modulator.
This network, which can form part of any DC level shifting and gain adjustment circuitry, forms an
important part of the transmit signal filtering. The ground connection to the capacitor C1 should be
positioned to give maximum attenuation of high-frequency noise into the modulator.
The component values should be chosen so that the product of the resistance and the capacitance is:
For a BT of 0.3 R1.C1 = 0.34/bit rate (bps)
For a BT of 0.5 R1.C1 = 0.22/bit rate (bps)
GMSK Modem CMX589A
2002 CML Microsystems Plc 7 D/589A/4
Data Rates
(kbps) BT = 0.3 BT = 0.5
R1 C1 R1 C1
4 120k 680pF 120k 470pF
4.8 100k 680pF 100k 470pF
8 91k 470pF 120k 220pF
9.6 91k 390pF 47k 470pF
16 47k 470pF 91k 150pF
19.2 100k 180pF 91k 120pF
32 47k 220pF 47k 150pF
38.4 * 47k 180pF 47k 120pF
64 * 56k 100pF 51k 68pF
80 * 39k 68pF
128 * 82k 22pF
144 * 68k 22pF
160 * 62k 22pF
176 * 56k 22pF
192 * 51k 22pF
* VDD 4.5V, external clock
Table 3: Data Rate vs. BT and Selected External Component Values
Note: In all cases, the value of R1 should not be less than 20.0k, and that the calculated value of C1
includes calculated parasitic capacitance.
2. R3, R4 and C6 form the gain components for the Rx Input signal. R3 should be chosen as required by the
signal input level.
3. For bit rate 64kbps, R4 = 100k. For bit rate > 64kbps, R4 = 10k.
4. The values chosen for C2 and C3 (including stray capacitance), should be suitable for the applied VDD
and the frequency of X1.
As a guide: C2 = C3 = 33pF at 1.0MHz falling to 18pF at the maximum frequency.
At 3.0V, C2 = C3 = 33pF falling to 18pF at 5.0MHz the equivalent series resistance of X1 should be less
than 2.0K falling to 150 at the maximum frequency. Stray capacitance on the Xtal/Clock circuit pins
must be minimized.
5. For bit rate 64kbps, C6 = 22pF. For bit rate > 64kbps, C6 = ×π×× 10k 2 rate bit 31
e.g. for 128kbps, C6 = 41.1pF.
6. C7 and C8 should both be .015µF for a data rate of 8kbps, and inversely proportional to the data rate for
other data rates, e.g. 0.030µF at 4kbps, 1800pF at 64kbps, 680pF at 192kbps.
7. The tolerance of C9 is not very critical because it primarily serves as a dc blocking capacitor.
8. The CMX589A can operate correctly with the Xtal frequencies between 1.0MHz and 16.0MHz
(VDD = 5.0V) and 1.0MHz to 5.0MHz (VDD = 3.0V). External clock frequencies up to 25.6MHz
(VDD 4.5V) are also supported (See Table 4 for examples.) For best results, a crystal oscillator design
should drive the clock inverter input with signal levels of at least 40% of VDD, peak to peak. Tuning fork
crystals generally cannot meet this requirement. To obtain crystal oscillator design assistance, consult
your crystal manufacturer. Operation of this device without a Xtal or Clock input may cause device
damage.
GMSK Modem CMX589A
2002 CML Microsystems Plc 8 D/589A/4
4 General Description
4.1 Clock Oscillator Divider
The Tx and (nominal) Rx data rates are determined by division of the frequency present at the XTALN pin as
generated by the on-chip Xtal oscillator, with external components, or supplied from an external source.
The division ratio is controlled by the logic level inputs on ClkDivA and ClkDivB pins as shown in Table 4,
together with an indication of how various standard data rates may be derived from common µP Xtal
frequencies.
A/B)(ClkDiv Ratio Division Frequency Xtal/Clk
Rate Data =
Xtal/Clock Frequency (MHz)
24.576*
8.192 4.9152 4.096 2.4576 2.048
Inputs 12.288/3 12.288/5 6.144/3
ClkDivA ClkDivB
Rate
Data
Freq Xtal/Clk
Data Rate (kbps)
0 0 128 192* 64* 38.4* 32 19.2 16
0 1 256 96* 32 19.2 16 9.6 8
1 0 512 48* 16 9.6 8 4.8 4
1 1 1024 24* 8 4.8 4
* VDD 4.5V, external clock
Table 4: Example Clock/Data Rates
Note: The device operation is not guaranteed above 200kbps or below 4kbps at the relevant supply voltage.
Figure 4: Minimum µµController System Connections
4.2 Receive
4.2.1 Rx Signal Path Description
The function of the Rx circuitry is to:
1. Set the incoming signal to a usable level.
2. Clean the signal by filtering.
3. Provide dc level thresholds for clock and data extraction.
4. Provide clock timing information for data extraction and external circuits.
5. Provide Rx data in a binary form.
6. Assess signal quality and provide Signal-to-Noise information.
GMSK Modem CMX589A
2002 CML Microsystems Plc 9 D/589A/4
The output of the radio receiver's Frequency Discriminator should be fed to the CMX589A's Rx Filter by a
suitable gain and DC level adjusting circuit. This circuit can be built with external components around the on-
chip Rx Input Amplifier. The gain should be set so that the signal level at the Rx Feedback pin is nominally
1V peak to peak (for VDD=5.0V) centered around VBIAS when receiving a continuous 1111000011110000..
data pattern.
Positive going signal excursions at Rx Feedback pin will produce a logic ‘0’ at the Rx Data Output. Negative
going excursions will produce a logic ‘1’.
The received signal is fed through the lowpass Rx Filter, which has a -3dB corner frequency of 0.56 times the
data bit-rate, before being applied to the Level Measure and Clock and Data extraction blocks.
The Level Measuring block consists of two voltage detectors, one of which measures the amplitude of the
positive parts of the received signal. The other measures the amplitude of the negative portions. (Positive
refers to signal levels higher than VDD/2, and negative to levels lower than VDD/2.) External capacitors are
used by these detectors, via the Doc1 and Doc2 pins, to form voltage ‘hold’ or ‘integrator’ circuits. These two
levels are then used to establish the optimum DC level decision-thresholds for the Clock and Data extraction,
depending upon the Rx signal amplitude and any DC offset.
4.2.2 Rx Circuit Control Modes
The operating characteristics of the Rx Level Measurement and Clock Extraction circuits are controlled, as
shown in Table 6, by logic level inputs applied to the PLLacq, Rx HOLDN and RxDCacq pins to suit a
particular application, or to cope with changing reception conditions, reference Figure 5.
In general, a data transmission will begin with a preamble, for example, 1100110011001100, to allow the
receive modem to establish timing and level-lock as quickly as possible. After the Rx carrier has been
detected, and during the time that the preamble is expected, the RxDCacq and PLLacq Inputs should be
switched from a logic ‘0’ to a logic ‘1’ so that the Level Measuring and Clock Extraction modes are operated
and sequenced as shown.
The Rx HOLDN input should normally be held at a logic ‘1’ while data is being received, but may be driven to
a logic ‘0’ to freeze the Level Measuring Clock Extraction circuits during a fade. If a fade lasts for less than
200 bit periods, normal operation can be resumed by returning the Rx HOLDN input to a logic ‘1’ at the end of
the fade. For longer fades, it may be better to reset the Level Measuring circuits by placing the RxDCacq to a
logic ‘1’ for 10 to 20 bit periods.
Rx HOLDN has no effect on the Level Measuring circuits while RxDCacq is at a logic ‘1’, and has no effect on
the PLL while PLLacq is at a logic ‘1’.
A logic ‘0’ on Rx HOLDN does not disable the Rx Clock output, and the Rx Data Extraction and S/N Detector
circuits will continue to operate.
Figure 5: Rx Mode Control Diagram
GMSK Modem CMX589A
2002 CML Microsystems Plc 10 D/589A/4
PLLacq Rx
HOLDN PLL Action
1 1 Acquire Sets the PLL bandwidth wide enough to allow a lock to the
received signal in less than 8 zero crossings. This mode will
operate as long as PLLacq is a logic “1”.
1 to 0 1 Medium
Bandwidth The correction applied to the extracted clock is limited to a
maximum of ±1/16th bit-period for every two received zero-
crossings. The PLL operates in this mode for a period of
about 30 bits immediately following a 1 to 0 transition of the
PLLacq input, provided that the Rx HOLDN input is a logic
‘1’.
0 1 Narrow
Bandwidth The correction applied to the extracted clock is limited to a
maximum of ±1/64th bit-period for every two received zero-
crossings. The PLL operates in this mode whenever the Rx
HOLDN Input is a logic ‘1’ and PLLacq has been a logic ‘0’
for at least 30 bit periods (after Medium Bandwidth operation
for instance).
0 0 Hold The PLL feedback loop is broken, allowing the Rx Clock to
freewheel during signal fade periods.
Table 5: PLL Action Measurement Operational Modes
RxDCacq Rx
HOLDN Rx Level Measure Action
0 to 1 X Clamp Operates for one bit-time after a 0 to 1 transition of the
RXDCacq input. The external capacitors are rapidly charged
towards a voltage mid-way between the received signal input
level and VBIAS, with the charge time-constant being of the
order of 0.5 bit-time.
1 X Fast Peak Detect The voltage detectors act as peak-detectors, one capacitor is
used to capture the positive-going signal peaks of the Rx
Filter output signal and the other capturing the negative-
going peaks. The detectors operate in this mode whenever
the RXDCacq input is at a logic ‘1’, except for the initial 1-bit
Clamp-mode time.
0 1 Averaging Peak
Detect Provides a slower but more accurate measurement of the
signal peak amplitudes.
0 0 Hold The capacitor charging circuits are disabled so that the
outputs of the voltage detectors remain substantially at the
last readings (discharging very slowly [time-constant approx.
2,000 bits] towards VBIAS).
X = Do not care
Table 6: Rx Level Measurement Operational Modes
4.2.3 Rx Clock Extraction
Synchronized by a PLL circuit to zero-crossings of the incoming data, the Rx Clock Extraction circuitry
controls the Rx Clock output. The Rx Clock is also used internally by the Data Extraction circuitry. The PLL
parameters can be varied by the Rx Circuit Control inputs PLLacq and Rx HOLDN to operate in one of four
PLL modes as described in Table 5 and Table 6.
4.2.4 Rx Data Extraction
The Rx Data Extraction circuit decides whether each received bit is a 1 or 0 by sampling the received signal,
after filtering, and comparing the sample values to an adaptive threshold derived from the Level Measuring
circuit. This threshold is adapted from bit to bit to compensate for intersymbol interference caused by the and
limiting of the overall transmission path and the Gaussian premodulation filter. Extracted data is output from
the Rx Data pin, and should be sampled externally on the rising edge of the Rx CLK.
GMSK Modem CMX589A
2002 CML Microsystems Plc 11 D/589A/4
4.2.5 Rx S/N Detection
The Rx S/N Detector system classifies the incoming zero-crossings as GOOD or BAD depending upon the
time when each crossing actually occurs with respect to its expected time as determined by the Clock
Extraction PLL. This information is then processed to provide a logic level output at the Rx S/N pin. A high
level indicates a series of GOOD crossings; a low level indicates a BAD crossing.
By averaging this output, it is possible to derive a measure of the Signal-to-Noise-Ratio and hence the
Bit-Error-Rate of the received signal.
Figure 6: Typical Bit-Error-Rate Performance at VDD = 5.0V
Note: Figure 6 indicates typical performance, independent of bit rate (although the applied noise bandwidth is
considered to match the bit rate used), radio performance (e.g. IF filter distortion), supply voltage (higher bit
rates require VDD 4.5V), and other ‘real world’ factors.
GMSK Modem CMX589A
2002 CML Microsystems Plc 12 D/589A/4
4.2.6 Rx Signal Quality
The effect of input Rx Signal quality on the Rx S/N output is shown in Figure 7.
Figure 7: Typical Rx S/N Output High Time (%) vs. Input S/N
4.3 Transmit
4.3.1 Tx Signal Path Description
The binary data applied to the Tx Data input is retimed within the chip on each rising edge of the Tx Clock and
then converted to a 1-volt peak-to-peak binary signal centred at VBIAS (for VDD= 5.0V)
If the Tx Enable input is high, then this internal binary signal will be connected to the input of the Lowpass Tx
Filter, and the output of the filter connected to the Tx Out pin.
Tx Enable Tx Filter Input Tx Out Pin
1 Data @ 5
VDD VP-P
e.g. 1VP-P for VDD=5V
Filtered ‘Tx Filter Input’
0 VBIAS VBIAS via 500k
A ‘low’ input to the Tx Enable will connect the input of the Tx Filter to VBIAS, and disconnect the Tx Out pin
from the filter, connecting it instead to VBIAS through a high resistance (nominally 500k).
The Tx Filter has a lowpass frequency response, which is approximately gaussian in shape as shown in Figure
9, to minimize amplitude and phase distortion of the binary signal while providing sufficient attenuation of the
high frequency-components which would otherwise cause interference into adjacent radio channels. The actual
filter bandwidth to be used in any particular application will be determined by the overall system requirements.
The attenuation-vs.-frequency response of the transmit filtering provided by the CMX589A has been designed to
meet the specifications for most GMSK modem systems that are -3dB bandwidth switchable between 0.3 and
0.5 times the data bit-rate (BT).
Note: An external RC network is required between the Tx Out pin and the input to the Frequency Modulator
(see Figure 2 and Figure 3). This network, which can form part of any DC level shifting and gain adjustment
circuitry, forms an important part of the transmit signal filtering. The ground connection to capacitor C1
should be positioned to give maximum attenuation of high-frequency noise into the modulator.
The signal at Tx Out is centered around VBIAS, going positive for logic ‘1’ (high) level inputs to the Tx Data
input and negative for logic ‘0’ (low) inputs.
When the transmit circuits are put into a powersave mode (by a logic ‘1’ to the Tx PS pin) the output voltage
of the Tx Filter will go to high impedance.
GMSK Modem CMX589A
2002 CML Microsystems Plc 13 D/589A/4
When power is subsequently restored to the Tx filter, its output will take several bit-times to settle. The Tx
Enable input can be used to prevent these abnormal voltages from appearing at the Tx Out pin.
Figure 8: Rx and Tx Clock Data Timings
Figure 9: Tx Filter Response
GMSK Modem CMX589A
2002 CML Microsystems Plc 14 D/589A/4
Figure 10: Typical Transmit Eye Patterns
Figure 11: Tx Output Spectrum (Random Data)
4.4 Data Formats
The receive section of the CMX589A works best with data which has a reasonably random structure --the
data should contain approximately the same number of ‘ones’ as ‘zeroes’ with no long sequences (>100 bits)
of consecutive ones or zeroes. Also, long sequences (>100 bits) of 10101010 ... patterns should be avoided.
For this reason, it is recommended that data be made random in some manner before transmission, for
example by exclusive-ORing it with the output of a binary pseudo-random pattern generator.
Where data is transmitted in bursts, each burst should be preceded by a preamble designed to allow the
receive modem to establish timing and level lock as quickly as possible. This preamble for BT=0.3 should be
at least 16 bits long, and should preferably consist of alternating pairs of ones and zeros i.e.
110011001100....; the eye of pattern 10101010 .... has the most gradual slope and will yield poor peak levels
for the Rx circuits. For BT=0.5 the eye pattern of 10101010... has reduced intersymbol interference and may
be used as the preamble (DC Acq pin should be held high during preamble). See Figure 5.
4.5 Acquisition and Hold Modes
The RXDCacq and PLLacq inputs must be pulsed High for about 16 bits at the start of reception to ensure that
the DC measurement and timing extraction circuits lock-on to the received signal correctly. Once lock has
been achieved, the above inputs should be taken Low again.
In most applications, there will be a DC step in the output voltage from the receiver FM discriminator due to
carrier frequency offsets as channels are changed or when the remote transmitter is turned on.
The CMX589A can tolerate DC offsets in the received signal of at least ±10% of VDD with respect to VBIAS,
(measured at the Rx Feedback pin). However, to ensure that the DC offset compensation circuit operates
correctly and with minimum delay, the Low to High transition of the RXDCacq and PLLacq inputs should occur
after the mean input voltage to the CMX589A has settled to within about 0.1V of its final value.
Note: This can place restrictions on the value of any series signal coupling capacitor.
GMSK Modem CMX589A
2002 CML Microsystems Plc 15 D/589A/4
As well as using the Rx Hold input to freeze the Level Measuring and Clock Extraction circuits during a signal
fade, it may also be used in systems which use a continuously transmitting control channel to freeze the Rx
circuitry during transmission of a data packet, allowing reception to resume afterwards without losing bit
synchronization. To achieve this, the CMX589A Xtal clock needs to be accurate enough that the derived
RxClock output does not drift by more than about 0.1 bit time from the actual received data-rate during the
time that the RxHold input is ‘Low’.
However; the RXDCacq input may need to be pulsed High for 2 bit durations to re-establish the level
measurements if the RxHold input is Low for more that a few hundred bit-times (exact number depends on
system crystal tolerances).
The voltages on the Doc1 and Doc2 pins reflect the average peak positive and negative excursions of the
(filtered) receive signal, and could therefore be used to derive a measure of the data signal amplitude.
Note: These pins are driven from very high-impedance circuits, so that the DC load presented by any
external circuitry should exceed 10M to VBIAS.
5 Application
5.1 Radio Channel Requirements
To achieve legal adjacent channel performance at high bit-rates, a radio with an accurate carrier frequency
and an accurate modulation index is required. For optimum channel utilization, (e.g. low BER and high data-
rates) attention must be paid to the phase and frequency response of both the IF and baseband circuitry.
5.1.1 Bit Rate, BT, and Bandwidth
The maximum data rate that can be transmitted over a radio channel depends on the following:
Channel spacing
Allowable adjacent channel interference
Tx filter bandwidth
Peak carrier deviation (Modulation Index)
Tx and Rx carrier frequency accuracies
Modulator and Demodulator linearity
Rx IF filter frequency and phase characteristics
Use of error correction techniques
Acceptable error-rate
As a guide to MOBITEX operation, a raw data-rate of 8kbps at 12.5kHz channel spacing may be achievable -
depending on local regulatory requirements- using a ±2kHz maximum deviation, a BT of 0.3, and no more
than 1.5kHz discrepancy between Tx and Rx carrier frequencies. Forward error correction (FEC) could then
be used with interleaving to reduce the effect of burst errors.
Reducing the data-rate to 4.8kbps would allow the BT to be increased to 0.5, improving the error-rate
performance.
5.1.2 FM Modulator, Demodulator and IF
For optimum performance, the eye pattern of the received signal (when receiving random data) applied to the
CMX589A should be as close as possible to the Transmit eye pattern examples shown in Figure 10.
Of particular importance are general symmetry, cleanliness of the zero-crossings, and for a BT of 0.3, the
relative amplitude of the inner eye opening.
To achieve this, attention must be paid to:
Linearity and frequency/phase response of the Tx frequency modulator. Unless the transmit data is
especially encoded to remove low frequency components, the modulator frequency response should
extend down to a few hertz. This is because two-point modulation is necessary for synthesized
radios.
Bandwidth and phase response of the Rx IF filters.
Accuracy of the Tx and Rx carrier frequencies -any difference will shift the received signal towards
one of the skirts of the IF filter response.
GMSK Modem CMX589A
2002 CML Microsystems Plc 16 D/589A/4
Ideally, the Rx demodulator should be DC coupled to the CMX589A Rx Signal In pin (with a DC bias
added to center the signal at the Rx Feedback pin at VDD/2 [VBIAS]). However, AC coupling can be
used provided that:
The 3dB cut-off frequency is 20Hz or below (i.e. a 0.1µF capacitor in series with 100k).
The data does not contain long sequences of consecutive ones or zeroes.
Sufficient time is allowed after a step change at the discriminator output (resulting from channel
changing or the appearance of a RF carrier) for the voltage into the CMX589A to settle before the
RXDCacq line is strobed.
5.1.3 Two-Point Modulation
When designing the CMX589A into a radio that uses a frequency synthesizer, a two-point modulation
technique is recommended. This is both to prevent the radio's PLL circuitry from counteracting the
modulation process, and to provide a clean flat modulation response down to DC.
Figure 12 shows a suggested basic configuration to provide a two-point modulation drive from the CMX589A
Tx Output using the FX019 or MX019 Digitally Controlled Quad Amplifier Array. The FX019/MX019 elements
provide individual set-up, calibration and dynamic control of modulation levels. Level setting control of the
amplifiers/attenuators of the FX019/MX019 is via an 8-bit data word. Note that the FX019/MX019 frequency
response only supports data rates as high as 8kbps.
With reference to Figure 12:
The buffer amplifier is required to prevent loading of the CMX589A external RC circuit.
Stage B, with R1/R2, provides suitable signal and DC levels for the VCO varactor; C1 is RF
decoupling. The drive level should be adjusted (digitally) to provide the desired deviation.
Stage C, with R3/R4, provides the Reference Oscillator drive (application dependent). This
parameter is set by adjusting for minimum AC signal on the PLL control voltage with a low-frequency
modulating signal (inside the PLL bandwidth) applied.
Stage D could be used with the components shown if a negative reference drive is required.
Stage A provides buffering and overall level control.
Figure 12: An Example of Two-Point Modulation Drive with Individual Adjustment Using the
FX019/MX019
GMSK Modem CMX589A
2002 CML Microsystems Plc 17 D/589A/4
5.2 AC Coupling of Tx and Rx Signals
In practical applications, it is possible to arrange AC coupling between the CMX589A Tx Output and the
frequency modulator to cut-off at a very low frequency, such as 5.0Hz. AC coupling between the receive
discriminator and the input of the CMX589A may need a shorter time-constant to avoid problems from voltage
steps at the output of the discriminator when changing channels or when the distant transmitter turns on.
For these reasons, as well as to maintain reasonable BER, the optimum 3dB cut-off frequencies are around
5.0Hz in the Tx path and 20.0Hz in the Rx path.
Figure 13 shows the typical static Bit-Error-Rate performance of the CMX589A operating under nominal
conditions for various degrees of AC coupling at the Rx input and the Tx output.
Data Rate = 8kbps VDD = 5.0V TAMB = 25°C Tx BT = 0.3
Figure 13: Effect of AC Coupling on Typical Bit-Error Rate
Any AC Coupling at the receive input will transform any step in the voltage at the discriminator output to a
slowly decaying pulse which can confuse the modem’s level measuring circuits. As illustrated in Figure 14,
the time for this step to decay to 37% of its original value is ‘RC’ where:
network) RC the offrequency cutoff 3dB (the21
RC π
=
which is 32ms, or 256 bit times at 8kbps, for a 5Hz network.
Figure 14: Decay time-AC Coupling
GMSK Modem CMX589A
2002 CML Microsystems Plc 18 D/589A/4
6 Performance Specifications
6.1 Electrical Specifications
6.1.1 Absolute Maximum Limits
Exceeding these maximum ratings can result in damage to the device.
General Notes Min. Typ. Max. Units
Supply (VDD-VSS) -0.3 7.0 V
Voltage on any pin to VSS -0.3 VDD + 0.3 V
Current
VDD -30 30 mA
VSS -30 30 mA
Any other pin -20 20 mA
D2 / P4 Packages
Total allowable Power dissipation
at TAMB = 25°C 800 mW
Derating above 25°C 13 mW/°C
Operating Temperature -40 85 °C
Storage Temperature -55 125 °C
D5 Package
Total allowable Power dissipation
at TAMB = 25°C 550 mW
Derating above 25°C 9 mW/°C
Operating Temperature -40 85 °C
Storage Temperature -55 125 °C
E2 Package
Total allowable Power dissipation
at TAMB = 25°C
320
mW
Derating above 25°C 5.3 mW/°C
Operating Temperature -40 85 °C
Storage Temperature -55 125 °C
Table 7: Absolute Maximum Ratings
GMSK Modem CMX589A
2002 CML Microsystems Plc 19 D/589A/4
6.1.2 Operating Limits
Correct Operation of the device outside these limits is not implied.
Notes Min. Typ. Max. Units
Supply (VDD-VSS) 3.0 3.3/5.0 5.5 V
Operating Temperature -40 85 °C
Rx and Tx Data Rate
VDD 3.0V 4 32 kbps
VDD 4.5V 4 200 kbps
Xtal Frequency
VDD 3.0V 1.0 5.0 MHz
VDD 4.5V 1.0 16.0 MHz
External Clock Frequency
VDD 3.0V 1 1.0 5.0 MHz
VDD 4.5V 1 1.0 25.6 MHz
High Pulse Width 1 15 ns
Low Pulse Width 1 15 ns
Table 8: Operating Limits
Operating Limits Notes
1. Timing for an external clock input to the Xtal/Clock pin.
GMSK Modem CMX589A
2002 CML Microsystems Plc 20 D/589A/4
6.1.3 Operating Characteristics
For the following conditions unless otherwise specified.
VDD = 5.0V @ TAMB = 25°C
Xtal/Clock Frequency = 4.096MHz, Data Rate = 8kbps, Noise Bandwidth = Bit Rate
Static Values Notes Min. Typ. Max. Units
Supply Current Tx PS Rx PS 1
IDD (VDD = 3.0V)
1 1 - 0.5 - mA
0 1 - 1.0 - mA
1 0 - 1.0 - mA
0 0 - 1.5 - mA
IDD (VDD = 5.0V)
1 1 - 1.0 - mA
0 1 - 2.0 - mA
1 0 - 3.0 - mA
0 0 - 4.0 - mA
Input Logic Level
Logic 1 Input Level 3.5 - - V
Logic 0 Input Level - - 1.5 V
Logic Input Current 2 -5.0 - 5.0 µA
Output Logic Level
Logic 1 Output Level (IOH = 120µA) 4.6 - - V
Logic 0 Output Level (IOL = -120µA) - - 0.4 V
Transmit Parameters -
Tx OUT pin DC bias shift caused by change from
Tx Enable = 0 to Tx Enable = 1 while
Tx PSAVE = 0 at 25°C
-85.0 - 85.0 mV
Tx OUT, Output Impedance 3 - 1.0 - k
Tx Out, Level 4, 10 0.8 1.0 1.2 VP-P
Output DC Offset 12 -0.125 - 0.125 V
Tx Data Delay
BT = 0.3 5 - 2.0 2.5 bit-
periods
BT = 0.5 5 - 1.5 2.0 bit-
periods
Tx PS to Output-Stable time 6 - 4.0 - bit-
periods
Receive Parameters
Rx Amplifier
Input Impedance 1.0 - - M
Output Impedance 7 - 10.0 - K
Voltage Gain - 50.0 - dB
Rx Filter Signal Input Level 8, 10 0.7 1.0 1.3 VP-P
Rx Time Delay 9 - - 3.0 bit-
periods
GMSK Modem CMX589A
2002 CML Microsystems Plc 21 D/589A/4
Static Values Notes Min. Typ. Max. Units
On-Chip Xtal Oscillator
RIN 10.0 - - M
ROUT 11 - 50.0 - k
Voltage Gain 11 - 25.0 - dB
Table 9: Operating Characteristics
Operating Characteristics Notes:
1. Not including current drawn from the CMX589A pins by external circuitry. See Absolute Maximum
Ratings.
2. For VIN in the range VSS to VDD.
3. For a load of 10K or greater. Tx PS input at logic ‘0’; Tx Enable = ‘1’.
4. Data pattern of 1111000011110000…
5. Measured between the rising edge of Tx Clock and the centre of the corresponding bit at Tx Out.
6. Time between the falling edge of the TXPSAVE and the Tx Out voltage stabilizing to normal output
levels.
7. For a load of 10k or greater. RXPSAVE input at logic ‘0’.
8. For optimum performance, Measured at the Rx Feedback pin for an 1111000011110000… pattern.
9. Measured between the center of bit at Rx Signal In and corresponding rising edge of the Rx Clock.
10. Levels are proportional to applied VDD
11. Small signal measurement at 1.0kHz with no load on Xtal output.
12. (Tx OUT enabled DC level) (Tx Out disabled DC level) when transmitting a repeating 11110000 bit
pattern.
GMSK Modem CMX589A
2002 CML Microsystems Plc 22 D/589A/4
6.2 Packages
Figure 15: 24-pin TSSOP Mechanical Outline: Order as part no. CMX589AE2
Figure 16: 24-pin SSOP Mechanical Outline: Order as part no. CMX589AD5
GMSK Modem CMX589A
Handling precautions: This product includes input protection, however, precautions should be taken to prevent device damage from
electro-static discharge. CML does not assume any responsibility for the use of any circuitry described. No IPR or circuit patent
licences are implied. CML reserves the right at any time without notice to change the said circuitry and this product specification. CML
has a policy of testing every product shipped using calibrated test equipment to ensure compliance with this product specification.
Specific testing of all circuit parameters is not necessarily performed.
CML Microcircuits
(UK ) Ltd
Oval Park - Langford - Maldon -
Essex - CM9 6WG - England.
Tel: +44 (0)1621 875500
Fax: +44 (0)1621 875600
Sales: sales@cmlmicro.com
Technical Support:
techsupport@cmlmicro.com
CML Microcircuits
(USA) Inc.
4800 Bethania Station Road -
Winston-Salem - NC 27105 - USA.
Tel: +1 336 744 5050,
800 638 5577
Fax: +1 336 744 5054
Sales: us.sales@cmlmicro.com
Technical Support:
us.techsupport@cmlmicro.com
CML Microcircuits
(Singapore) Pte Ltd
COMMUNICATIONSEMICONDUCTORS
No 2 Kallang Pudding Road - 09 to
05/06 Mactech Industrial Building -
Singapore 349307
Tel: +65 7450426
Fax: +65 7452917
Sales: sg.sales@cmlmicro.com
Technical Support:
sg.techsupport@cmlmicro.com
Figure 17: 24-pin SOIC Mechanical Outline: Order as part no. CMX589AD2
Figure 18: 24-pin PDIP Mechanical Outline: Order as part no. CMX589AP4