LD1117 Adjustable and fixed low drop positive voltage regulator Datasheet - production data flows mostly into the load. Only a very common 10 F minimum capacitor is needed for stability. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1 % at 25 C. The adjustable LD1117 is pin to pin compatible with the other standard. Adjustable voltage regulators maintaining the better performances in terms of drop and tolerance. DPAK TO-220 SOT-223 SO-8 Features * Low dropout voltage (1 V typ.) * 2.85 V device performances are suitable for SCSI-2 active termination * Output current up to 800 mA * Fixed output voltage of: 1.2 V, 1.8 V, 2.5 V, 3.3 V, 5.0 V * Adjustable version availability (VREF = 1.25 V) * Internal current and thermal limit * Available in 1 % (at 25 C) and 2 % in full temperature range * Supply voltage rejection: 75 dB (typ.) Description The LD1117 is a low drop voltage regulator able to provide up to 800 mA of output current, available even in adjustable version (VREF = 1.25 V). Concerning fixed versions, are offered the following output voltages: 1.2 V, 1.8 V, 2.5 V, 2.85 V, 3.3 V and 5.0 V. The device is supplied in: SOT-223, DPAK, SO-8 and TO-220. The SOT223 and DPAK surface mount packages optimize the thermal characteristics even offering a relevant space saving effect. High efficiency is assured by NPN pass transistor. In fact in this case, unlike than PNP one, the quiescent current November 2013 This is information on a product in full production. DocID2572 Rev 33 1/44 www.st.com 44 Contents LD1117 Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7 LD1117 adjustable: application note . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 Packing mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 10 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 2/44 DocID2572 Rev 33 LD1117 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical characteristics of LD1117#12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Electrical characteristics of LD1117#18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electrical characteristics of LD1117#25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Electrical characteristics of LD1117#33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Electrical characteristics of LD1117#50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Electrical characteristics of LD1117 (adjustable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Electrical characteristics of LD1117#12C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical characteristics of LD1117#18C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Electrical characteristics of LD1117#25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Electrical characteristics of LD1117#33C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Electrical characteristics of LD1117#50C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Electrical characteristics of LD1117C (adjustable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 TO-220 mechanical data (type STD-ST Dual Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 TO-220 mechanical data (type STD-ST Single Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SOT-223 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SO-8 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DPAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Footprint data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SOT-223 tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 SO-8 tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 DPAK tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 DocID2572 Rev 33 3/44 List of figures LD1117 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. 4/44 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Application circuit (for 1.2 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Application circuit (for other fixed output voltages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Negative supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Circuit for increasing output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Voltage regulator with reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Battery backed-up regulated supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Post-regulated dual supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Adjustable output voltage application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Adjustable output voltage application with improved ripple rejection . . . . . . . . . . . . . . . . . 24 Drawing dimension TO-220 (type STD-ST Dual Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Drawing dimension TO-220 (type STD-ST Single Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . 28 Drawing dimension SOT-223 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Drawing dimension SO-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Drawing dimension DPAK (type STD-ST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Drawing dimension DPAK (type Fujitsu-subcon.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Drawing dimension DPAK (type IDS-subcon.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 DPAK footprint recommended data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Drawing dimension tube for TO-220 Dual Gauge (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Drawing dimension tube for TO-220 Single Gauge (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . 36 Tape for SOT-223 (dimensions are in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Reel for STO-223 (dimensions are in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 SO-8 tape and reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 DPAK footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Tape for DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Reel for DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 DocID2572 Rev 33 LD1117 1 Diagram Diagram Figure 1. Block diagram DocID2572 Rev 33 5/44 Pin configuration 2 LD1117 Pin configuration Figure 2. Pin connections (top view) SO-8 SOT-223 TO-220 DPAK Note: 6/44 The TAB is connected to the VOUT. DocID2572 Rev 33 LD1117 Maximum ratings 3 Maximum ratings Table 1. Absolute maximum ratings Symbol Value Unit DC input voltage 15 V PTOT Power dissipation 12 W TSTG Storage temperature range -40 to +150 C -40 to +125 C TOP Operating junction temperature range 0 to +125 C VIN (1) Parameter for C version for standard version 1. Absolute maximum rating of VIN = 18 V, when IOUT is lower than 20 mA. Table 2. Thermal data Symbol Parameter SOT-223 SO-8 DPAK TO-220 Unit RthJC Thermal resistance junction-case 15 20 8 5 C/W RthJA Thermal resistance junction-ambient 110 55 100 50 C/W DocID2572 Rev 33 7/44 Schematic application 4 LD1117 Schematic application Figure 3. Application circuit (for 1.2 V) Figure 4. Application circuit (for other fixed output voltages) 8/44 DocID2572 Rev 33 LD1117 5 Electrical characteristics Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, CO = 10 F, R = 120 between GND and OUT pins, unless otherwise specified. Table 3. Electrical characteristics of LD1117#12 Symbol Parameter Test condition Min. Typ. Max. Unit VO Output voltage Vin = 3.2 V, IO = 10 mA, TJ = 25 C 1.188 1.20 1.212 V VO Output voltage IO = 10 to 800 mA Vin - VO = 1.4 to 10 V 1.140 1.20 1.260 V VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA 0.035 0.2 % VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA 0.1 0.4 % VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage Iadj Adjustment pin current Vin 15 V Adjustment pin current change 0.5 % 0.3 % 15 V 60 120 A Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 A Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin - VO = 3 V, Vripple = 1 VPP Iadj IO(min) SVR Vd Dropout voltage Thermal regulation 800 60 0.003 % 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W 9/44 Electrical characteristics LD1117 Refer to the test circuits, TJ = 0 to 125 C, CO = 10 F, unless otherwise specified. Table 4. Electrical characteristics of LD1117#18 Symbol Parameter Test condition Min. Typ. Max. Unit 1.8 1.82 V 1.84 V VO Output voltage Vin = 3.8 V, IO = 10 mA, TJ = 25 C 1.78 VO Output voltage IO = 0 to 800 mA, Vin = 3.3 to 8 V 1.76 VO Line regulation Vin = 3.3 to 8 V, IO = 0 mA 1 6 mV VO Load regulation Vin = 3.3 V, IO = 0 to 800 mA 1 10 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 8 V IO Output current Vin = 6.8 V, TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 10/44 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, CO = 10 F, unless otherwise specified. Table 5. Electrical characteristics of LD1117#25 Symbol Parameter Test condition Min. Typ. Max. Unit 2.5 2.525 V 2.55 V VO Output voltage Vin = 4.5 V, IO = 10 mA, TJ = 25 C 2.475 VO Output voltage IO = 0 to 800 mA, Vin = 3.9 to 10 V 2.45 VO Line regulation Vin = 3.9 to 10 V, IO = 0 mA 1 6 mV VO Load regulation Vin = 3.9 V, IO = 0 to 800 mA 1 10 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 10 V IO Output current Vin = 7.5 V TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W 11/44 Electrical characteristics LD1117 Refer to the test circuits, TJ = 0 to 125 C, CO = 10 F, unless otherwise specified. Table 6. Electrical characteristics of LD1117#33 Symbol Parameter Test condition Min. Typ. Max. Unit 3.3 3.333 V 3.365 V VO Output voltage Vin = 5.3 V, IO = 10 mA, TJ = 25 C 3.267 VO Output voltage IO = 0 to 800 mA, Vin = 4.75 to 10 V 3.235 VO Line regulation Vin = 4.75 to 15 V, IO = 0 mA 1 6 mV VO Load regulation Vin = 4.75 V, IO = 0 to 800 mA 1 10 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 15 V IO Output current Vin = 8.3 V, TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 6.3 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 12/44 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, CO = 10 F, unless otherwise specified. Table 7. Electrical characteristics of LD1117#50 Symbol Parameter Test condition Min. Typ. Max. Unit 5 5.05 V 5.1 V VO Output voltage Vin = 7 V, IO = 10 mA, TJ = 25 C 4.95 VO Output voltage IO = 0 to 800 mA, Vin = 6.5 to 15 V 4.9 VO Line regulation Vin = 6.5 to 15 V, IO = 0 mA 1 10 mV VO Load regulation Vin = 6.5 V, IO = 0 to 800 mA 1 15 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 15 V IO Output current Vin = 10 V, TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 8 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W 13/44 Electrical characteristics LD1117 Refer to the test circuits, TJ = 0 to 125 C, CO = 10 F, unless otherwise specified. Table 8. Electrical characteristics of LD1117 (adjustable) Symbol Parameter Test condition Min. Typ. Max. Unit 1.238 1.25 1.262 V 1.275 V 0.035 0.2 % 0.1 0.4 % Vref Reference voltage Vin - VO = 2 V, IO = 10 mA, TJ = 25 C Vref Reference voltage IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V 1.225 VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA VO Temperature stability VO Long term stability Vin Operating input voltage Iadj Adjustment pin current 1000 hrs, TJ = 125 C 0.5 % 0.3 % 15 V 60 120 A Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA 1 5 A Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin - VO = 3 V, Vripple = 1 VPP Iadj IO(min) SVR Vd Dropout voltage Thermal regulation 14/44 Vin 15 V 800 60 0.003 % 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = -40 to 125 C, CO = 10 F, R = 120 between GND and OUT pins, unless otherwise specified. Table 9. Electrical characteristics of LD1117#12C Symbol Parameter Test condition Min. Typ. Max. Unit VO Output voltage Vin - VO = 2 V, IO = 10 mA, TJ = 25 C 1.176 1.20 1.224 V VO Output voltage IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V 1.120 1.20 1.280 V VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA 1 % VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA 1 % VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage Iadj Adjustment pin current Vin 15 V Iadj Adjustment pin current change IO(min) 0.5 % 0.3 % 15 V 60 120 A Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 A Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin - VO = 3 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 800 60 0.003 % 75 dB IO = 100 mA, TJ = 0 to 125 C 1 1.1 IO = 500 mA, TJ = 0 to 125 C 1.05 1.2 IO = 800 mA, TJ = 0 to 125 C 1.10 1.3 Ta = 25 C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 33 V %/W 15/44 Electrical characteristics LD1117 Refer to the test circuits, TJ = -40 to 125 C, CO = 10 F, unless otherwise specified. Table 10. Electrical characteristics of LD1117#18C Symbol Parameter Test condition Min. Typ. Max. Unit 1.8 1.84 V 1.87 V VO Output voltage Vin = 3.8 V, IO = 10 mA, TJ = 25 C 1.76 VO Output voltage IO = 0 to 800 mA, Vin = 3.9 to 10 V 1.73 VO Line regulation Vin = 3.3 to 8 V, IO = 0 mA 1 30 mV VO Load regulation Vin = 3.3 V, IO = 0 to 800 mA 1 30 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 8 V IO Output current Vin = 6.8 V TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 16/44 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA, TJ = 0 to 125 C 1 1.1 IO = 500 mA, TJ = 0 to 125 C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 C, 30 ms Pulse DocID2572 Rev 33 0.01 0.1 V V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = -40 to 125 C, CO = 10 F, unless otherwise specified. Table 11. Electrical characteristics of LD1117#25C Symbol Parameter Test condition Min. Typ. Max. Unit 2.5 2.55 V 2.6 V VO Output voltage Vin = 4.5 V, IO = 10 mA, TJ = 25 C 2.45 VO Output voltage IO = 0 to 800 mA, Vin = 3.9 to 10 V 2.4 VO Line regulation Vin = 3.9 to 10 V, IO = 0 mA 1 30 mV VO Load regulation Vin = 3.9 V, IO = 0 to 800 mA 1 30 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 10 V IO Output current Vin = 7.5 V TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA, TJ = 0 to 125 C 1 1.1 IO = 500 mA, TJ = 0 to 125 C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 C, 30 ms Pulse DocID2572 Rev 33 0.01 0.1 V V %/W 17/44 Electrical characteristics LD1117 Refer to the test circuits, TJ = -40 to 125 C, CO = 10 F, unless otherwise specified. Table 12. Electrical characteristics of LD1117#33C Symbol Parameter Test condition Min. Typ. Max. Unit 3.3 3.36 V 3.44 V VO Output voltage Vin = 5.3 V, IO = 10 mA, TJ = 25 C 3.24 VO Output voltage IO = 0 to 800 mA, Vin = 4.75 to 10 V 3.16 VO Line regulation Vin = 4.75 to 15 V, IO = 0 mA 1 30 mV VO Load regulation Vin = 4.75 V, IO = 0 to 800 mA 1 30 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 15 V IO Output current Vin = 8.3 V, TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 6.3 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 18/44 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA, TJ = 0 to 125 C 1 1.1 IO = 500 mA, TJ = 0 to 125 C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 C, 30 ms Pulse DocID2572 Rev 33 0.01 0.1 V V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = -40 to 125 C, CO = 10 F, unless otherwise specified. Table 13. Electrical characteristics of LD1117#50C Symbol Parameter Test condition Min. Typ. Max. Unit 5 5.1 V 5.2 V VO Output voltage Vin = 7 V, IO = 10 mA, TJ = 25 C 4.9 VO Output voltage IO = 0 to 800 mA, Vin = 6.5 to 15 V 4.8 VO Line regulation Vin = 6.5 to 15 V, IO = 0 mA 1 50 mV VO Load regulation Vin = 6.5 V, IO = 0 to 800 mA 1 50 mV VO Temperature stability VO Long term stability 1000 hrs, TJ = 125 C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin 15 V IO Output current Vin = 10 V, TJ = 25 C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin = 8 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 V 75 dB IO = 100 mA, TJ = 0 to 125 C 1 1.1 IO = 500 mA, TJ = 0 to 125 C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 C, 30 ms Pulse DocID2572 Rev 33 0.01 0.1 V V %/W 19/44 Electrical characteristics LD1117 Refer to the test circuits, TJ = -40 to 125 C, CO = 10 F, unless otherwise specified. Table 14. Electrical characteristics of LD1117C (adjustable) Symbol Parameter Test condition Min. Typ. Max. Unit 1.225 1.25 1.275 V 1.3 V Vref Reference voltage Vin - VO = 2 V, IO = 10 mA, TJ = 25 C Vref Reference voltage IO = 10 to 800 mA, Vin - VO= 1.4 to 10 V VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA 1 % VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA 1 % VO Temperature stability VO Long term stability Vin Operating input voltage Iadj Adjustment pin current 1.2 1000 hrs, TJ = 125 C 0.5 % 0.3 % 15 V 60 120 A Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA 1 10 A Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 C Vin - VO = 3 V, Vripple = 1 VPP Iadj IO(min) SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 20/44 Vin 15 V 800 60 0.003 % 75 dB IO = 100 mA, TJ = 0 to 125 C 1 1.1 IO = 500 mA, TJ = 0 to 125 C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 C, 30 ms Pulse DocID2572 Rev 33 0.01 0.1 V V %/W LD1117 6 Typical application Typical application Figure 5. Negative supply Figure 6. Circuit for increasing output voltage Figure 7. Voltage regulator with reference DocID2572 Rev 33 21/44 Typical application LD1117 Figure 8. Battery backed-up regulated supply 22/44 DocID2572 Rev 33 LD1117 Typical application Figure 9. Post-regulated dual supply DocID2572 Rev 33 23/44 LD1117 adjustable: application note 7 LD1117 LD1117 adjustable: application note The LD1117 adjustable has a thermal stabilized 1.25 0.012 V reference voltage between the OUT and ADJ pins. IADJ is 60 A typ. (120 A max.) and IADJ is 1 A typ. (5 A max.). R1 is normally fixed to 120 . From Figure 9 we obtain: VOUT = VREF + R2 (IADJ +IR1) = VREF + R2 (IADJ +VREF /R1) = VREF (1 + R2 / R1) + R2 x IADJ. In normal application R2 value is in the range of few k, so the R2 x IADJ product could not be considered in the VOUT calculation; then the above expression becomes: VOUT = VREF (1 + R2 / R1). In order to have the better load regulation it is important to realize a good Kelvin connection of R1 and R2 resistors. In particular R1 connection must be realized very close to OUT and ADJ pin, while R2 ground connection must be placed as near as possible to the negative Load pin. Ripple rejection can be improved by introducing a 10 F electrolytic capacitor placed in parallel to the R2 resistor (see Figure 10). Figure 10. Adjustable output voltage application Figure 11. Adjustable output voltage application with improved ripple rejection 24/44 DocID2572 Rev 33 LD1117 8 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Table 15. TO-220 mechanical data (type STD-ST Dual Gauge) mm Dim. Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 P 3.75 3.85 Q 2.65 2.95 DocID2572 Rev 33 25/44 Package mechanical data LD1117 Figure 12. Drawing dimension TO-220 (type STD-ST Dual Gauge) BW\SH$B5HYB7 26/44 DocID2572 Rev 33 LD1117 Package mechanical data Table 16. TO-220 mechanical data (type STD-ST Single Gauge) mm Dim. Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 0.51 0.60 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 P 3.75 3.85 Q 2.65 2.95 DocID2572 Rev 33 27/44 Package mechanical data LD1117 Figure 13. Drawing dimension TO-220 (type STD-ST Single Gauge) BUHY' 28/44 DocID2572 Rev 33 LD1117 Package mechanical data Table 17. SOT-223 mechanical data mm Dim. Min. Typ. A Max. 1.80 A1 0.02 0.1 B 0.60 0.70 0.85 B1 2.90 3.00 3.15 c 0.24 0.26 0.35 D 6.30 6.50 6.70 e 2.30 e1 4.60 E 3.30 3.50 3.70 H 6.70 7.00 7.30 V 10 Figure 14. Drawing dimension SOT-223 0046067_M DocID2572 Rev 33 29/44 Package mechanical data LD1117 Table 18. SO-8 mechanical data mm Dim. Min. Typ. A Max. 1.75 A1 0.10 0.25 A2 1.25 b 0.28 0.48 c 0.17 0.23 D 4.80 4.90 5.00 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 e 1.27 h 0.25 0.50 L 0.40 1.27 L1 k 1.04 0 8 ccc 0.10 Figure 15. Drawing dimension SO-8 0016023_Rev_G 30/44 DocID2572 Rev 33 LD1117 Package mechanical data Table 19. DPAK mechanical data Dim. Min. Type Fujitsu-subcon. Type IDS-subcon mm. mm. mm. Typ. Max. Min. Typ. Max. Min. Typ. Max. 2.30 2.35 2.19 2.38 A 2.20 2.40 2.25 A1 0.90 1.10 0.96 1.06 0.89 1.14 A2 0.03 0.23 0 0.10 0.03 0.23 b 0.64 0.90 0.76 0.86 0.64 0.88 b4 5.20 5.40 5.28 5.38 5.21 5.46 c 0.45 0.60 0.46 0.56 0.46 0.58 c2 0.48 0.60 0.46 0.56 0.46 0.58 D 6.00 6.20 6.05 6.15 5.97 6.22 5.27 5.47 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 2.23 4.40 4.60 H 9.35 10.10 L 1.00 L1 2.80 L2 0.80 0.60 R V2 6.55 6.65 6.35 1.00 2.28 2.33 2.28 4.51 4.61 10.42 10.30 9.40 1.40 1.60 0.90 2.50 2.65 1.03 1.13 0.89 1.27 0.70 0.90 0.64 1.02 0.40 8 6.73 4.70 9.90 0.20 0 6.60 5.20 4.77 e1 L4 Note: Type STD-ST 0 0.20 8 0 8 The DPAK package coming from the two subcontractors (Fujitsu and IDS) are fully compatible with the ST's package suggested footprint. DocID2572 Rev 33 31/44 Package mechanical data LD1117 Figure 16. Drawing dimension DPAK (type STD-ST) 0068772/G Note: 32/44 1 Maximum resin gate protrusion: 0.5 mm. 2 Maximum resin protrusion: 0.25 mm. DocID2572 Rev 33 LD1117 Package mechanical data Figure 17. Drawing dimension DPAK (type Fujitsu-subcon.) 0068772/G DocID2572 Rev 33 33/44 Package mechanical data LD1117 Figure 18. Drawing dimension DPAK (type IDS-subcon.) 0068772/G 34/44 DocID2572 Rev 33 LD1117 Package mechanical data Table 20. Footprint data Values mm. inch. A 6.70 0.264 B 6.70 0.64 C 1.8 0.070 D 3.0 0.118 E 1.60 0.063 F 2.30 0.091 G 2.30 0.091 Figure 19. DPAK footprint recommended data DocID2572 Rev 33 35/44 Packaging mechanical data 9 LD1117 Packaging mechanical data Figure 20. Drawing dimension tube for TO-220 Dual Gauge (mm.) Figure 21. Drawing dimension tube for TO-220 Single Gauge (mm.) 36/44 DocID2572 Rev 33 LD1117 Packaging mechanical data Table 21. SOT-223 tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Typ. Max. Min. Max. A0 6.75 6.85 6.95 A B0 7.30 7.40 7.50 N K0 1.80 1.90 2.00 W1 12.4 F 5.40 5.50 5.60 W2 18.4 E 1.65 1.75 1.85 W3 W 11.7 12 12.3 P2 1.90 2 2.10 Base quantity pcs 1000 P0 3.90 4 4.10 Bulk quantity pcs 1000 P1 7.90 8 8.10 T 0.25 0.30 0.35 D 1.50 1.55 1.60 D1 1.50 1.60 1.70 180 60 11.9 15.4 Figure 22. Tape for SOT-223 (dimensions are in mm) *Cumulative tolerance of 10 sprocket holes is 0.20 mm DocID2572 Rev 33 37/44 Packaging mechanical data LD1117 Figure 23. Reel for SOT-223 (dimensions are in mm) 38/44 DocID2572 Rev 33 LD1117 Packaging mechanical data Table 22. SO-8 tape and reel mechanical data mm Dim. Min. Typ. A Max. 330 C 12.8 D 20.2 N 60 13.2 T 22.4 Ao 8.1 8.5 Bo 5.5 5.9 Ko 2.1 2.3 Po 3.9 4.1 P 7.9 8.1 Figure 24. SO-8 tape and reel dimensions DocID2572 Rev 33 39/44 Packaging mechanical data LD1117 Table 23. DPAK tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 18.4 22.4 Figure 25. DPAK footprint(a) 6.7 1.8 3 1.6 2.3 6.7 2.3 1.6 a. All dimensions are in millimeters 40/44 DocID2572 Rev 33 AM08850v1 LD1117 Packaging mechanical data Figure 26. Tape for DPAK 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 W K0 B0 For machine ref. only including draft and radii concentric around B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 27. Reel for DPAK T REEL DIMENSIONS 40mm min. Access hole At sl ot location B D C N A Full radius Tape slot in core for tape start 25 mm min. width G measured at hub AM08851v2 DocID2572 Rev 33 41/44 Order codes 10 LD1117 Order codes Table 24. Order codes Packages SOT-223 SO-8 DPAK (Tape and reel) TO-220 TO-220 (Dual Gauge) Output voltages LD1117S12TR LD1117DT12TR 1.2 V LD1117S12CTR LD1117DT12CTR 1.2 V LD1117S18TR LD1117DT18TR LD1117S18CTR LD1117DT18CTR 1.8 V LD1117S25TR LD1117DT25TR 2.5 V LD1117S25CTR LD1117DT25CTR 2.5 V LD1117S33TR LD1117S33CTR LD1117S50TR LD1117D33TR LD1117D33CTR LD1117DT33TR LD1117V18 LD1117V33 LD1117DT33CTR LD1117V33C LD1117DT50TR LD1117V50 1.8 V LD1117V33-DG 3.3 V LD1117V33C-DG 3.3 V 3.3 V LD1117V50-DG 5V 5V LD1117S50CTR LD1117DT50CTR LD1117V50C LD1117STR LD1117DTTR LD1117V 5V LD1117V-DG ADJ from 1.25 to 15 V ADJ from 1.25 to 15 V LD1117SC-R 42/44 LD1117DTC-R DocID2572 Rev 33 ADJ from 1.25 to 15 V LD1117 11 Revision history Revision history Table 25. Document revision history Date Revision 22-Sep-2004 15 Add new part number #12C; typing error: note on table 2. 25-Oct-2004 16 Add Vref reference voltage on table 12. 18-Jul-2005 17 The DPAK mechanical data updated. 25-Nov-2005 18 The TO220FM package removed. 14-Dec-2005 19 The Top on table 2 updated. 06-Dec-2006 20 DPAK mechanical data updated and added footprint data. 05-Apr-2007 21 Order codes updated. 30-Nov-2007 22 Added Table 1. 16-Apr-2008 23 Modified: Table 24 on page 42. 08-Jul-2008 24 Added note 1. on page 7. 30-Mar-2009 25 Modified: VIN max value Table 4 on page 10 and Figure 9 on page 23. 29-Jul-2009 26 Modified: Table 24 on page 42. 03-Feb-2010 27 Modified Table 9 on page 15. 22-Mar-2010 28 Added: Table 16 on page 22, Figure 13 on page 23, Figure 14 on page 24, Figure 17 and Figure 18 on page 33. 15-Nov-2010 29 Modified: RthJC value for TO-220 Table 2 on page 7. 30-Nov-2011 30 Added: order code LD1117V33-DG Table 24 on page 42. 13-Feb-2012 31 Added: order codes LD1117V50-DG and LD1117V-DG Table 24 on page 42. 19-Oct-2012 32 Added: RthJA value for DPAK, SOT-223 and SO-8Table 2 on page 7. 33 Part number LD1117xx changed to LD1117. Updated the Description in cover page, Section 8: Package mechanical data and Table 24: Order codes. Cancelled Table 1: Device summary. Added Section 9: Packaging mechanical data. Minor text changes. 20-Nov-2013 Changes DocID2572 Rev 33 43/44 LD1117 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER'S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR "AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL" INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 44/44 DocID2572 Rev 33 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: STMicroelectronics: STEVAL-MKI111V1